WARNING!
Electronic Emission Notices
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with instructions
contained in this manual, may cause harmful interference to radio and television communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-
-
-
-
REORIENT OR RELOCATE THE RECEIVING ANTENNA
INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER
CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE:
Connecting this device to peripheral devices that do not comply with Class B requirements, or
using an unshielded peripheral data cable, could also result in harmful interference to radio or
television reception.
The user is cautioned that any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
To ensure that the use of this product does not contribute to interference, it is necessary to use
shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for
errors or omissions is assumed. Neither is any liability assumed for damages resulting from the
use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective
owners.
CAUTION:
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled
where possible. Disposal of used batteries must be in accordance with local environmental
regulations.
1
Intel D2700-ITX series Motherboard
Table of Contents
Motherboard Specifications----------------------------------------------------------------------------------4
Motherboard Layout--------------------------------------------------------------------------------------------6
Hardware Installation-------------------------------------------------------------------------------------------10
Safety Instructions-------------------------------------------------------------------------------------------10
Installing Memory Modules--------------------------------------------------------------------------------11
Installing the Motherboard---------------------------------------------------------------------------------12
Installing the I/O Shield--------------------------------------------------------------------------------12
Securing the Motherboard into the Chassis------------------------------------------------------12
Installing an mSATA SSD module (optional)-----------------------------------------------------13
Connecting Cables and Setting Switches--------------------------------------------------------------14
24-pin ATX Power Connector-PW1 (for ATX version)------------------------------------------15
4-pin ATX_12V Power Connector-PW2 (for ATX version)------------------------------------15
DC OUT Connector-CN12 (for DC-DC version)-------------------------------------------------16
SPDIF-Out Header-CN5------------------------------------------------------------------------------17
COM Header-CN4 (optional)-------------------------------------------------------------------------17
Front Panel Header-FP1------------------------------------------------------------------------------17
USB Headers-FP_U1----------------------------------------------------------------------------------18
Front Pannel Audio Header-FP_S1----------------------------------------------------------------18
Fan Connectors-----------------------------------------------------------------------------------------19
Serial-ATA (SATA) Connectors (SATA1/2)--------------------------------------------------------19
Expansion Slots-----------------------------------------------------------------------------------------20
Jumper Settings-----------------------------------------------------------------------------------------21
Configuring the BIOS-------------------------------------------------------------------------------------------22
Enter BIOS Setup--------------------------------------------------------------------------------------------22
Main Menu-----------------------------------------------------------------------------------------------------22
X-Setting Menu-----------------------------------------------------------------------------------------------23
Advanced Menu----------------------------------------------------------------------------------------------24
OnBoard Device Config-------------------------------------------------------------------------------24
HDD Storage Configuration--------------------------------------------------------------------------24
CPU Configuration--------------------------------------------------------------------------------------25
USB Configuration--------------------------------------------------------------------------------------25
Intel Fast Flash Standby------------------------------------------------------------------------------26
PC Health Menu----------------------------------------------------------------------------------------------26
Power Management Menu---------------------------------------------------------------------------------27
Boot Menu------------------------------------------------------------------------------------------------------28
Save & Exit Menu--------------------------------------------------------------------------------------------29
Save Changes and Exit-------------------------------------------------------------------------------29
Discard Changes and Exit----------------------------------------------------------------------------30
Save Changes and Reset-----------------------------------------------------------------------------30
2
Table of Contents
Discard Changes and Reset-------------------------------------------------------------------------30
Save Changes-------------------------------------------------------------------------------------------30
Discard Changes----------------------------------------------------------------------------------------30
Restore Defaults----------------------------------------------------------------------------------------30
Save as User Defaults---------------------------------------------------------------------------------30
Restore User Defaults---------------------------------------------------------------------------------30
Launch EFI Shell from filesystem device---------------------------------------------------------30
Flash Update Procedure -----------------------------------------------------------------------------------31
Installing Drivers and Software-----------------------------------------------------------------------------32
Drivers Installation -------------------------------------------------------------------------------------------32
Realtek HD Audio Driver Setup --------------------------------------------------------------------------41
Getting Started-------------------------------------------------------------------------------------------41
Digital Output---------------------------------------------------------------------------------------------41
Speakers---------------------------------------------------------------------------------------------------43
Microphone------------------------------------------------------------------------------------------------44
Line In------------------------------------------------------------------------------------------------------45
Device Adavanced Settings---------------------------------------------------------------------------46
Connector Settings--------------------------------------------------------------------------------------46
Information ------------------------------------------------------------------------------------------------47
3
Intel D2700-ITX series Motherboard
Motherboard Specifications
qChipset
v Intel NM10
q Size
v Mini ITX form factor of 6.7 X 6.7 inch
q Microprocessor support
v Intel Atom D2700
q Operating systems
v Supports Windows Vista 32bit/64bit and Windows 7 32bit/64bit
q System Memory
v Two 204-pin SO-DIMMs DDR3-1066
v Maximum memory size: 4 GB
q USB 2.0 ports
v Supports hot plug and play
v Six USB 2.0 ports (four ports on the back panel, two via the USB brackets connected to
the internal USB header)
v Supports USB 2.0 protocol up to 480 Mbps transmission rate
q USB 3.0 ports
v Supports hot plug and play
v Two USB 3.0 ports on the back panel
v Fully backward compatible with USB 2.0 and 1.1 specifications
q Onboard Serial ATA ports
v Independent DMA operation on two ports
v Two SATAII ports (3.0 Gb/s)
q Onboard LAN
v Support Full Duplex flow control (IEEE802.3x)
v 10/100/1000 BASE-T IEEE 802.3 compliant
v Wake On LAN (WOL) power management support
q WiFi/Bluetooth support
v Compliant with IEEE802.11n Draft 2.0 Standard
v High speed wireless connection and enhanced wireless security
v Max transfer rate up to 150 Mbps (optional for different models)
4
Motherboard Specifications
q Audio
v 8 channel High Definition Audio (including one optical SPDIF output port)
v All DACs support 192k/96k/48k/44.1kHz sample rate
v One SPDIF-out header on board
q Green Function
v Supports ACPI (Advanced Configuration and Power Interface)
q Graphics Features
v GeForce GT 520 GPU, DirectX11
v DVI/HDMI/DP output (VGA compatible with adapter)
v Support up to 2560x1600 resolution
q Expansion slots
v One PCI Express x16 slot (single lane)
v One half-sized Mini PCI Express slot (vertical)
v One full-sized Mini PCI Express slot for mSATA SSD
5
Intel D2700-ITX series Motherboard
Motherboard Layout
The motherboard inludes two versions: ATX version and DC-DC version. Users please refer to
the corresponding layout picture below.
Figure 1 for ATX version:
17
1819 20 21
K/B USB2.0
PW2
DP/HDMI
DDRIII-2
DDRIII-1
CPUFAN1
1.5V
1.5V
Chipset
GPU
SYSFAN1
DVI/WIFI
1
PW1
USB3.0
16
15
2
J2
J1
SATA1
LAN/USB
FP_S1
CN5
SW2
CN4
AUDIO
SW1
FP1
JP1
SATA2
FP_U1
SPK1
5
PCIE2
14 13 12
11 10
9
3
4
8 76
Figure 1. Board Layout (ATX version)
1. SYS Fan Connector-SYS_FAN1
2. 24-pin ATX Power Connector-PW1
3. Power on Button_SW2
4. Front Panel Header-FP1
5. Speaker Header-SPK1
6. Clear CMOS Jumper-JP1
7. Reset Button-SW1
8. Mini PCI Express Slot for mSATA SSD-J2
9. PCI Express x16 Slot-PCIE2
10. USB 2.0 Header-FP_U1
11. Serial-ATA (SATA) Connectors (SATA1/2)
6
12. COM Header-CN4
13. SPDIF-Out Header-CN5
14. Front Panel Audio Header-FP_S1
15. Mini PCI Express Slot-J1
16. Backpanel Connectors
17. GPU
18. Chipset
19. 4-pin ATX_12V Power Connector-PW2
20. CPU Fan Connector-CPU_FAN
21. DDRIII Sockets-DDRIII-1~2
Motherboard layout
Figure 2 for DC-DC version:
18
19 20
K/B USB2.0
17
CN12
DDRIII-2
DDRIII-1
CPUFAN1
DP/HDMI
1
1.5V
1.5V
Chipset
GPU
SYSFAN1
DVI/WIFI
2
USB3.0
16
15
J2
J1
SATA1
LAN/USB
FP_S1
CN5
SW2
CN4
AUDIO
SW1
FP1
JP1
SATA2
FP_U1
SPK1
5
PCIE2
14 13 12
Figure 2. Board Layout (DC-DC version)
1. DC-OUT Connector-CN12
2. SYS Fan Connector-SYS_FAN1
3. Power on Button_SW2
4. Front Panel Header-FP1
5. Speaker Header-SPK1
6. Clear CMOS Jumper-JP1
7. Reset Button-SW1
8. Mini PCI Express Slot for mSATA SSD-J2
9. PCI Express x16 Slot-PCIE2
10. USB 2.0 Header-FP_U1
11 10
9
3
4
8 76
11. Serial-ATA (SATA) Connectors (SATA1/2)
12. COM Header-CN4
13. SPDIF-Out Header-CN5
14. Front Panel Audio Header-FP_S1
15. Mini PCI Express Slot-J1
16. Backpanel Connectors
17. GPU
18. Chipset
19. CPU Fan Connector-CPU_FAN
20. DDRIII Sockets-DDRIII-1~2
7
Intel D2700-ITX series Motherboard
Figure 3. Backpanel Connectors
For ATX version
10 9
8
1 2
3
For DC-DC version
7
4
6
1
11
5
1. USB 2.0 Ports
2. HDMI Port
3. DVI Port
4. USB 3.0 Ports
5. Optical SPDIF Output
6. Port
Blue
Green
Pink
Black
Orange
2-Channel
Line-In
Line-Out
Mic In
--
--
7. LAN port LED indicators
Speed LED Activity LED
4-Channel
Line-In
Front Speaker Out
Mic In
-Rear Speaker Out
6-Channel
Line-In
Front Speaker Out
Mic In
Center/Subwoofer
Rear Speaker Out
Speed LED
8-Channel
Side Speaker Out
Front Speaker Out
Mic In
Center/Subwoofer
Rear Speaker Out
Activity LED
Status
Description
Status
Descritption
Off
Speed: 10 Mbps
Off
No link
Green
Speed: 100 Mbps
Orange
Linked
Orange
Speed: 1000 Mbps
Blinking
Data activity
8. WiFi antenna connectors (Optional)
This motherboard can support two WiFi antenna modules. Refer to the following to install
the WiFi antenna modules.
Step 1. Remove the red caps from the WiFi antenna connectors.
Step 2. Install the WiFi antennas to the WiFi antenna connectors, and make sure the screws
are rotated in clockwise direction.
1.5V
1.5V



8

Rear panel
Note: 1. Users please note that the appearance of your WiFi antenna modules may
not be exactly the same as those shown in this manual.
2. Users can install one or two WiFi antennas to the motherboard.
3. Users can bend or rotate the WiFi antennas to the best receiving direction
according to the picture below.



9. DisplayPort
10. PS2 Keyboard Port
11. 19V DC Power input (for DC-DC version)
This motherboard contains a DC power input jack (as picture 1). Users can plug a 19V AC/
DC adapter to the DC power input jack (as picture 2). Please use a 19V DC power adapter
instead of ATX power supply. Picture 3 is the final image.
1.5V
2
1.5V
1
3
9
Intel D2700-ITX series Motherboard
Hardware Installation
This section will guide you through the installation of the motherboard. The topics covered in this
section are:
q Installing Memory Modules
q Installing the Motherboard
qConnecting Cables and Setting Switches
Safety Instructions
To reduce the risk of fire, electric shock, and injury, always follow basic safety precautions.
Remember to remove power from your computer by disconnecting the AC main source before
removing or installing any equipment from/to the computer chassis.
10
Hardware Installation
Installing Memory Modules
1.5V
1.5V
Your new motherboard has two 1.5V 204-pin slots for SO-DIMM DDR3 memory. These slots
support 1 GB/2 GB DDR3 devices. There must be at least one memory bank populated to ensure
normal operation. Refer to the following recommendations to install memory modules.
DDRIII-1
DDRIII-2
Note that a memory module has a notch, so it can only fit in one direction. Refer to the following
procedure to install memory modules into the slots on the motherboard.
1.Unlock a SO-DIMM slot by pressing the module clips outward.
2.Align the memory module to the SO-DIMM slot, and insert the module vertically into the
slot. The plastic clips at both sides of the slot automatically lock the SO-DIMM into the
connector.
Note: When installing only one SO-DIMM DDR3 module, please insert it into the DDRIII-2
slot.
11
Intel D2700-ITX series Motherboard
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis you are
using and if you are replacing an existing motherboard or working with an empty chassis. Determine if it would be easier to make all the connections prior to this step or to secure the motherboard and then make all the connections. It is normally easier to secure the motherboard first.
Use the following procedure to install the I/O shield and secure the motherboard into the chassis.
Note: Be sure that the CPU fan assembly has enough clearance for the chassis covers
to lock into place and for the expansion cards. Also make sure the CPU Fan assembly is
aligned with the vents on the covers.
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow
within the chassis.
Before installing the motherboard, install the I/O shield from the inside of the chassis. Press the
I/O shield into place and make sure it fits securely. If the I/O shield does not fit into the chassis,
you would need to obtain the proper size from the chassis supplier.
Securing the Motherboard into the Chassis
Most computer chassis have a base with mounting studs or spacers to allow the motherboard
to be secured to the chassis and help to prevent short circuits. If there are studs that do not
align with a mounting hole on the motherboard, it is recommended that you remove that stud
to prevent the possibility of a short circuit. In most cases, it is recommended to secure the
motherboard with spacers.
1.Carefully place the motherboard onto the studs/spacers located inside the chassis.
2.Align the mounting holes with the studs/spacers.
3.Align the connectors to the I/O shield.
4.Ensure that the fan assembly is aligned with the chassis vents according to the fan assembly
instruction.
5.Secure the motherboard with screws.
12
Hardware Installation
Installing an mSATA SSD module (optional)
The motherboard supports one mSATA SSD via mini PCIe slot. Users please install the mSATA
SSD module according to the following instructions.
1. Locate the Mini-PCIe slot of the motherboard, and insert an mSATA SSD into the slot at a 45
degree angle.
2. Gently press down on the mSATA SSD with one finger and secure the screws.
Note:
1. The motherboard shipped in the box does not contain an mSATA SSD.
2. You can only use either mSATA or SATA2 device at a time. The default working mode is
SATA2. The SATA2 will become unavailable when mSATA SSD is installed.
3. When the SATA2 device works, the LED indicator D2 red light is on; when the mSATA
device works, the LED indicator D2 green light is on.
LED indicators
D2
13
Intel D2700-ITX series Motherboard
Connecting Cables and Setting Switches
This section takes you through all the connectors and switch settings necessary on the motherboard. This will include:
qPower Connector
v 24-pin ATX Power Connector-PW1 (for ATX version)
v DC OUT Connector-CN12 (for DC-DC version)
v 4-pin ATX_12V Power Connector-PW2 (for ATX version)
q Internal Headers/Connectors
v SPDIF-Out Header-CN5
v COM Header-CN4
v Front Panel Header-FP1
v USB Headers (FP_U1)
v Front Panel Audio Header-FP_S1
q Serial-ATA (SATA) Connectors (SATA1/2)
q Fan Connectors
qExpansion Slots
qCMOS Jumper Settings
See Figure 1 to locate the connectors and jumpers referenced in the following procedure.
14
Hardware Installation
24-pin ATX Power Connector-PW1 (for ATX version)
PW1 is the main power supply connector. Make sure that the power supply cable and pins are
properly aligned with the connector on the motherboard. Firmly plug the power supply cable into
the connector and make sure it is secure.
PW2
1
PW1-Pin Definition
1.5V
1.5V
PW1
12
1
24
13
Pin
Signal
Pin
Signal
1
+3.3V
13
+3.3V
2
+3.3V
14
-12V
3
GND
15
GND
4
+5V
16
PS_ON
5
GND
17
GND
6
+5V
18
GND
7
GND
19
GND
8
PWROK
20
-5V
9
+5V_AUX
21
+5V
10
+12V
22
+5V
11
+12V
23
+5V
12
+3.3V
24
GND
4-pin ATX_12V Power Connector-PW2 (for ATX version)
PW2, the 4-pin ATX 12V power connector, is used to provide power to the CPU. Align the pins to
the connector and press firmly until seated.
PW2-Pin Definition
Pin
Signal
1
GND
2
GND
3
+12V
4
+12V
15
Intel D2700-ITX series Motherboard
DC OUT Connector-CN12 (for DC-DC version)
This motherboard can supply the power to SATA devices with a SATA power cable.
Users can plug a SATA power cable (as picture 7) to the DC out connector (as picture
8). Picture 9 is the final image.
1
CN12
7
9
16
Assignment
1
12V
2
GND
3
GND
4
5V
1.5V
1.5V

1.5V
1
PIN
8
1.5V
1.5V
1.5V
CN12-Pin Difinition
Hardware Installation
SPDIF-Out Header-CN5
This header provides a SPDIF (Sony/Philips Digital Interface) output to digital multimedia
device through coaxial connector.
CN5 - Pin Definition
COM Header-CN4 (optional)
CN4 - Pin Definition
Pin
Signal
Pin
Signal
1
DCD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
10
NC
CN4
Pin
Signal
1
GND
2
SPDIF-out
3
VCC
1
Pin
Signal
Pin
Signal
1
HDD_LED+
2
PW_LED+
3
HDD_LED-
4
PW_LED-
5
GND
6
PWR_SW
7
RESET
8
GND
9
NC
10
KEY
1.5V
The front panel header on this motherboard is
one connector used to connect the following four
cables :
FP1-Pin Definition
1.5V
Front Panel Header-FP1
1
CN5
FP1
q P
WRLED
Attach the front panel power LED cable to these two pins of the connector. The Power LED
indicates the system’s status.
q PWR SW
Attach the power button cable from the case to these two pins. Pressing the power button
on the front panel turns the system on and off rather than using the power supply button.
q HDD LED
Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator LED
indicates the activity status of the hard disks.
q
RST SW
Attach the Reset switch cable from the front panel of the case to these two pins. The system
restarts when the RESET switch is pressed.
Note:Some chassis do not have all four cables. Be sure to match the name on the
connectors to the corresponding pins.
17
Intel D2700-ITX series Motherboard
USB Headers-FP_U1
1.5V
1.5V
This motherboard contains four USB 2.0 and two USB 3.0 ports that are exposed on the rear
panel of the chassis. The motherboard also contains one 10-pin internal USB 2.0 header onboard.
Note: Secure the bracket to either the
front or rear panel of your chassis (not
all chassis are equipped with the front
panel option).
FP_U1-Pin Definition
FP_S1
1
1
PIN
Assignment
PIN
Assignment
1
VCC
2
VCC
3
USBP0-
4
USBP1-
5
USBP0+
6
USBP1+
7
GND
8
GND
9
KEY
10
NC
FP_U1
Front Panel Audio Header-FP_S1
The audio connector supports HD audio standard and provides two kinds of audio output choices:
the Front Audio, the Rear Audio. The front Audio supports retasking function.
FP_S1-Pin Definition
PIN
Assignment
PIN
Assignment
1
MIC2(L)
2
GND
3
MIC(R)
4
-ACZ-DET
5
Front Audio(R)
6
Reserved
7
FAVDIO-JD
8
Key(No pin)
9
Front Audio(L)
10
Reserved
Note:
In order to utilize the front audio header, your chassis must have front audio connector.
Also please make sure the pin assignment on the cable is the same as the pin
assignment on the mainboard header. To find out if the chassis you are buying supports
a front audio connector, please contact your dealer.
18
Hardware Installation
Fan Connectors
There are two fan connectors on the motherboard, including system fan connector-SYSFAN1
and CPU fan connector-CPUFAN1.
CPUFAN1
GND
+12V
Sense
Control
Sense
+12V
1.5V
1.5V
Control
GND
SATA1
SYSFAN1
SATA2
Serial-ATA (SATA) Connectors (SATA1/2)
The Serial ATA connector is used to connect the Serial ATA device to the motherboard. These
connectors support the thin Serial ATA cables for primary storage devices. The motherboard
incorporates two SATA II ports with maximum transfer rate up to 3.0 Gb/s each.
SATA-Pin Definition
Pin
Signal
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
19
Intel D2700-ITX series Motherboard
Expansion Slots
1.5V
1.5V
The motherboard contains three expansion slots, twe Mini PCIe slots and one PCIe x16 slot.
J1
J2
PCIE2
Mini PCI Express Slots-J1/J2
There are two Mini PCI Express slots. J1 supports one half-sized WiFi card. J2 supports one
mSATA SSD. (Please refer to page 13 to install the mSATA SSD module.)
PCI Express x16 Slot-PCIE_X16
There is one PCIe x16 slot reserved for graphics card. It is fully compliant with PCIE 2.0
specification.
20
Hardware Installation
Jumper Settings
This section explains how to configure the motherboard’s hardware. Before using your
computer, make sure all jumpers and DRAM modules are set correctly. Refer to this section
whenever in doubt.
CMOS Clear Jumper-JP1
JP1
Selection
1
1-2*
Normal*
1
2-3
CMOS Clear
Close
Open
* = Default setting.
If you want to clear the system configuration, use the JP1 (Clear CMOS Jumper) or SW1 (Clear CMOS Button) to
clear data.
Notice:
1. Be sure to save the CMOS setting when exit the CMOS.
2. If the CPU is frequency multiplier locked, no CPU speed change will be seen even if the
frequency multiplier setting in CMOS setup is changed.
21
Intel D2700-ITX series Motherboard
Configuring the BIOS
This section discusses how to change the system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
Enter BIOS Setup
The BIOS is the communication bridge between hardware and software. Correctly
setting the BIOS parameters is critical to maintain optimal system performance.
Refer to the following procedure to verify/change BIOS settings.
1. Power on the computer.
2. Press the Del key when the following message briefly displays at the bottom of
the screen during the Power On Self Test (POST).
Pressing Del takes you to the BIOS Setup Utility.
Note: 1. We reserve the right to update the BIOS version presented in the manual. The
BIOS pictures shown in this section are for reference only.
2. It is strongly recommended that you do not change the default BIOS settings.
Changing some settings could damage your system.
Main Menu
This menu gives you an overview of the general system specifications. The BIOS
automatically detects the items in this menu.
Note: Users please note
that the data in gray is nonchangeable, and the others are
for selection.
q
q
22
BIOS Information
Displays the auto-detected BIOS information.
CPU Information
Displays the auto-detected CPU information.
Configuring the BIOS
q
q
q
Memory Information
Displays the auto-detected memory information.
HDD Information
Displays the auto-detected HDD information.
System Date/Time
Allows you to set the system date/time.
X-Setting Menu
The X-Setting menu items show the settings of voltage control.
q
q
q
DRAM voltage Control
Use this item to set the DRAM voltage.
VCC voltage Control
Use this item to set the VCC voltage.
CHIP voltage Control
Use this item to set the chip voltage.
23
Intel D2700-ITX series Motherboard
Advanced Menu
The Advanced menu items allow you to change the setting for the CPU and other
system devices. Press <enter> to display the configuration options:
OnBoard Device Config
The items in this menu allow you to set PCI Express port, HD Audio and so on.
q PCI Express Port 0/1/2/3
Use this item to set the PCI Express Port.
q Launch PXE OpROM
Use this item to enable or disable Launch PXE OpROM.
q Launch Storage OpROM
Use this item to enable or disable Launch Storage OpROM.
q Azalia Controller
Use this item to set Azalia controller.
q Serial Port 0/1 Configuration
Press <Enter> to display the serial port configuration.
q CIR Controller Configuration
Press <Enter> to display the CIR controller configuration.
HDD Storage Configuration
The items in this menu allow you to set or change the storage configurations. Press
<enter> to display the configuration options:
q SATA Controller
Allows you to configure SATA controller.
q Configure SATA as
This item allows you to configure SATA as IDE/AHCI mode.
24
Configuring the BIOS
CPU Configuration
The items in this menu show the CPU-related information that the BIOS automatically
detects. Press <enter> to display the configuration options:
q Hyper-Threading
Enable this function for Windows and Linux4 OS, (OS supports Hyper Threading
Technology). Disable this function for other OS. (OS not optimized for Hyper
Threading Technology).
q Core-Multi Processing
Use this item to enable or disable Core-Multi processing.
q Execute Disable Bit
When disabled forces the XD feature flag to always return 0, defaults choose
[Enable].
q Limit CPUID Maximum
Allows you to determine whether to limit CPUID maximum value. Set this item
to [Disable] Windows operating system; set this item to [Enable] for legacy
operating system such as Windows NT4.0.
q Intel Virtualization Technology
Hardware Virtualization Technology enables processor feature for running multiple
simultaneous virtual machines allowing specialized software applications to run in
full isolation of each other.
USB Configuration
The items in this menu allow you to change the USB-related features. Press <enter>
to display the configuration options:
q USB Support
Allows you to enable or disable USB support.
q Legacy USB Support
Allows you to enable or disable support for USB devices on legacy operating
systems.
q EHCI Hand-Off
Allows you to enable support for operating systems without an EHCI hand-off
feature.
q USB transfer time-out
Allows you to set USB transfer time-out.
q Device reset time-out
Allows you to set device reset time-out.
q Device power-up delay
Allows you to set device power-up delay.
25
Intel D2700-ITX series Motherboard
Intel Fast Flash Standby
The items in this menu allow you to change Intel Fast Flash standby features. Press
<enter> to display the configuration options:
q iFFS Support
Use this item to enable or disable iFFS.
q Entry on S3 RTC Wake
Use this item to enable or disable entry on S3 RTC wake.
q Entry After
Use this item to set the number of minutes of entry after.
q Entry on S3 Critical Battery Wake
Use this item to enable or disable entry on S3 critical battery wake.
PC Health Menu
Select PC Health from the BIOS Setup Utility menu to display the system menu.
q CPU Fan Control Mode
Use this item to select CPU FAN Control mode.
q Duty Cycle
Use this item to select the fan dutycycle.
q Start Temperature
Use this item to select the start temperature.
q Start Fan Duty
Use this item to select the start fan dutycycle.
q Highest Fan Duty
Use this item to select the highest fan dutycycle.
26
Power Management Menu
The items in this menu allow you to control the system power management. Press
<Enter> to display the configuration options:
q Enable Hibernation
Enable or disable system ability to hibernation (OS/S4 Sleep State). This option
may be not effective with some OS.
q ACPI Sleep State
Select the highest ACPI sleep state, the system will enter when the SUSPEND
button is pressed.
q Restore AC Power Loss
This item allows you to configure how the system board responds to a power
failure.
q Logo indicate
Use this item to enable or disable logo indicate.
q DeepSleep (Erp Compliant)
When enabled, wake up from S4/S5 can only be done by power button.
q PS2 Wakeup S4&S5
Use this item to enable or disable PS2 wakeup S4 & S5.
q RTC Wakeup Setting
Use this item to enable or disable RTC wakeup.
27
Intel D2700-ITX series Motherboard
Boot Menu
The Boot menu items allow you to change the system boot options. Press <enter> to
display the configuration options:
q Setup Prompt Timeout
Use this item to set number of seconds to wait for setup activation key.
q Bootup NumLock State
Use this item to select the keyboard NumLock state: [On] or [Off].
q Security Settings
The security menu items allow you to change the system security settings. Press
<enter> to display the configuration options:
* Administrator Password
Select this item to set Setup Administrator Password.
* User Password
Select this item to set the user password.
To set an Administrator/User Password:
1. Select the item [Administrator/User Password] and press <Enter>.
2. From the password box, type a password composed of at least six letters and/or
numbers, then press <Enter>.
3. Confirm the password when prompted:
The message “Password Installed” appears after you successfully set your
password.
To change the administrator/user password, follow the same steps as setting a use
password.
To clear the administrator/user password, select the item [Administrator/User
password], then press <enter>. The message “Password Uninstalled” appears.
28
Configuring the BIOS
q Full Screen Logo
This option allows you to enable or disable the display of the full-screen logo
when the system boots. Use the <Page Up> and <Page Down> keys to toggle
between [Enable] and [Disable].
q GateA20 Active
When set to [Upon Request], GA20 can be disabled using BIOS services. When
set to [Always], GA20 can not be disabled; this option is useful when any RT code
is executed above 1MB.
q Option ROM Messages
Use this item to set display mode for Option.
q Interrupt 19 Capture
When set to [Enabled], this function allows the option ROMS to trap interrupt 19.
q Boot Option #1/2
This item displays the boot option.
Save & Exit Menu
The exit menu items allow you to load the option or failsafe default values for the BIOS
items, and save or discard your changes to the BIOS items. Press <enter> to display
the sub-menu:
Save Changes and Exit
Select this item and press <Enter> to save the changes that you have made in the
BIOS Setup and exit the BIOS Setup. When the diolog box [Save configuration and
exit?] appears, select [Yes] to save and exit, or select [No] to return to the main menu.
29
Intel D2700-ITX series Motherboard
Discard Changes and Exit
Select this option only if you do not want to save the changes that you have made
to the setup program. If you made changes to fields other than system date, system
time, and password, the BIOS asks for a confirmation before exiting.
Save Changes and Reset
Select this item and press <Enter> to reset the system after saving the changes.
When the diolog box [Save configuration and reset?] appears, select [Yes] to save
and reset, or select [No] to return to the main menu.
Discard Changes and Reset
Select this item and press <Enter> to reset system setup without saving any changes.
When the diolog box [Reset without saving?] appears, select [Yes] to discard and
reset, or select [No] to return to the main menu.
Save Changes
Select this item and press <Enter> to save the changes that you have made in the
BIOS Setup and exit the BIOS Setup. When the diolog box [Save configuration?]
appears, select [Yes] to save changes, or select [No] to return to the main menu.
Discard Changes
This option allows you to discard the selections you have made and restore the
previously saved values. When the dialog box [Load Previous Values?] appears,
select [Yes] to discard any change and load the previously saved values.
Restore Defaults
Use this item to restore/load default values for all the setup options.
Save as User Defaults
Use this item to save the changes as User Defaults.
Restore User Defaults
Use this item to restore the User Defaults to all the setup options.
Launch EFI Shell from filesystem device
Use this item to launch EFI Shell application (Shellx64.efi) from one of the available
filesystem devices.
30
Configuring the BIOS
FLASH Update Procedure
The program EFUDOS.exe is included in the driver dsk (X:\Utility\EFUDOS.exe). Please follow
the recommended procedure to update the flash BIOS, as listed below.
(X: your driver disk letter).
1. Create a DOS-bootable floppy diskette. Copy the new BIOS file (just obtained or downloaded)
and the utility program EFUDOS.exe to the diskette.
2. Allow the PC system to boot from the DOS diskette.
3. At the DOS prompt, type
EFUDOS XX.ROM /P /B /N <ENTER>
Note: XX (the BIOS file name) can be defined by users.
4. Wait until the flash-update is complete.
5. Restart the PC.
Warning: - Do not turn off or RESET the computer during the flash process.
- If you are not sure how to upgrade the BIOS, please take your computer to an
Authorized Service Center and have a trained technician do the work for you.
31
Intel D2700-ITX series Motherboard
Installing Drivers and Software
Note:
1. It is important to remember that before installing the driver disk that is shipped in the
kit, you need to load your operating system. The motherboard supports Windows Vista
32 bit/64 bit and Windows 7 32bit/64bit.
2. For best compatibility, please only use the onboard SATA or USB 2.0 ports as the OS
installation source drive connection.
The kit comes with a driver disk that contains utility drivers and additional software.
The driver disk that has been shipped with your motherboard contains the following software
and drivers:
q Intel Chipset Driver
q Realtek Sound Driver
q Nvidia Graphics Driver
q Realtek Network Driver
q Etron USB 3.0 Driver
q Intel Wireless Driver
Note: We reserve the right to update the driver version presented in the manual. The driver
installation pictures shown in this section are for reference only.
Drivers Installation
1. Insert the driver disk into the drive after loading your operating system, and then you can see
the interface below.
32
Installing Drivers And Software
2. Left-click Intel Chipset Driver, begin loading
33
Intel D2700-ITX series Motherboard
3. Left-click Realtek Sound Driver, begin loading
34
Installing Drivers And Software
4. Left-click Nvidia Graphics Driver, begin loading
35
Intel D2700-ITX series Motherboard
5. Left-click Realtek Network Driver, begin loading
36
Installing Drivers And Software
6. Left-click Etron USB 3.0 Driver, begin loading
37
Intel D2700-ITX series Motherboard
7. Left-click Intel Wireless Driver, begin loading
38
Installing Drivers And Software
39
Intel D2700-ITX series Motherboard
At last, you can enter Computer Management that provides information about the hardware
devices on this motherboard to check if the driver installation is complete.
40
Installing Drivers And Software
Realtek HD Audio Driver Setup
Getting Started
After Realtek HD Audio Driver being installed (insert the driver dsk and follow the on-screen
instructions), “Realtek HD Audio Manager” icon
will show in System tray as below. Double
click the icon and the control panel will appear:
Double click to enable
Realtek HD Audio Manager
Digital Output
After clicking on the “Sound Effect” tab, 3 sections “Environment”, “Equalizer” and “Karaoke”
are available for selection.
41
Intel D2700-ITX series Motherboard
Environment Simulation
You will be able to enjoy different sound experience by pulling down the arrow, totally 23 kinds
of sound effect will be shown for selection. Realtek HD Audio Sound Manager also provides five
popular settings “Sewer pipe”, “Bathroom”, “Arena”, “Stone Room”, and “Auditorium” for quick
enjoyment.
Equalizer Selection
Change to graphic EQ by clicking on the Equalizer icon
you to create your own preferred settings by utilizing this tool.
. The Equalizer section allows
In standard 10 bands of equalizer, ranging from 31Hz to 16kHz are available:
Frequently Used Equalizer Setting
Realtek recognizes the needs that you might have. By leveraging our long experience at audio
field, Realtek HD Audio Sound Manager provides you certain optimized equalizer settings that
are frequently used for your quick enjoyment.
How to Use
Other than the buttons “Pop” “Live” “Club” & “Rock” shown on the page, to pull down the arrow
in “Others” , you will find more optimized settings available to you.
Karaoke Mode
Karaoke mode brings Karaoke fun back home by simply using the music you usually play, Karaoke
mode can help you eliminate the vocal of the song or adjust the key to accommodate your range.
Vocal Cancellation: Single click on “Voice Cancellation”, the vocals of the songs will be erased,
while the background music is still playing which lets you take over the vocal part.
Key Adjustment: Using “Up/Down Arrow” to find a key which better fits your vocal range.
42
Installing Drivers And Software
Speakers
Realtek HD Audio Manager frees you from default speaker settings. Speakers includes four tabs:
Speaker Configuration, Sound Effects, Room Correction and Default Format.
Speaker Configuration
In this tab, you can choose speaker configuration: Stereo, Quadraphonic, 5.1 Speaker or 7.1
Speaker using “Up/Down Arrow”.
43
Intel D2700-ITX series Motherboard
Microphone
This page is designed to provide you better microphone/recording quality.
Below picture indicates both “Noise Suppression” & “Acoustic Echo Cancellation” are both enabled.
Noise Suppression
If you feel that the background noise, especially the sound generated from the fan inside PC, is
too loud? Try “Noise Suppression”, which allows you to cut off and suppress disturbing noise.
Acoustic Echo Cancellation
This function prevents playback sound from being recorded by microphone together with your
sound. For example, you might have chance to use VOIP function through Internet with your
friends. The voice of your friend will come out from speakers (playback). However, the voice of your
friend might also be recorded into your microphone then go back to your friend through Internet.
In that case, your friend will hear his/her own voice again. With AEC (Acoustic Echo Cancellation)
enabled at your side, your friend can enjoy the benefit with less echo.
44
Installing Drivers And Software
Line In
Realtek HD Audio Manager integrates “Volume Control” functions into the Line In page. This gives
you the advantage to you to create your favorite sound effect in one single tool.
Single click on the volume icon
mute mode.
, the Recording/Playback Volume will be changed to the
45
Intel D2700-ITX series Motherboard
Device Advanced Settings
Click on “Device advanced settings” at the upper right corner of Realtek HD Audio Manager page,
and you can set the playback device and recording device as below.
Connector Settings
Click on the icon
on the main page of Realtek HD Audio Manager, and the Connector Settings
dialog will display. There are two settings: “Disable front panel jack detection” and “Enable auto
popup dialog, when device has been plugged in”. After changing the settings, click “OK” to confirm.
46
Information
Click on the icon
at the lower right corner of Realtek HD Audio Manager page, the Realtek
HD Audio information will display.
Hardware / Software
information of your audio
system
Language setting
When “Audio” is chosen,
this language setting
would accommodate to
OS language on your
systems.
Quick launch button at system tray
This section provides information about your current system audio device.

The screenshots shown in this section are for Windows® 7 operating system.
47
Intel D2700-ITX series Motherboard
48
291-MA212-01