QSC Speaker SUBWOOFER FILTER User's Manual

Add to my manuals

advertisement

QSC Speaker SUBWOOFER FILTER User's Manual | Manualzz

SF-1

Subwoofer

Filter

9

FPO

Rev. A

10

SF-1 SUBWOOFER FILTER

INTRODUCTION

The SF-1 Subwoofer Filter is an upper slot accessory for QSC MXa Series amplifiers, which feature Level

One Open Input Architecture. The accessory mounts in the back of the amplifier above the standard input panel.

Ideal for adding subwoofer amplification to an existing full-range system, the SF-1 offers adjustable and selectable low-pass filtering for both channels of the amplifier, in addition to adjustable high-pass subsonic filtering. The filter slopes are 12 dB per octave, and the filter frequencies are programmable via provided

SIP resistor networks.

A slide switch, SW1, allows you to configure the SF-1 with a low-end “boost” which provides a suitable equalization for use with B6 speaker enclosures. A 10-position DIP switch, SW2, affords you the versatility of setting the accessory in many different configurations, such as mono summing and single channel bypass. The configuration process is detailed below.

The use of the SF-1 for cinema subwoofer installations can reduce the chance of speaker damage by digital soundtracks. Low frequency information, below the box tuning frequency, can destroy speakers at power levels far below their rated capacity. The SF-1 can remove these damaging frequencies and also provide the needed equalization to flatten and extend the response of popular cinema subwoofers. These include:

Electro-Voice models TL880D, TL550D, TL3512, TL440 and JBL 4645 and 4645B.

Existing cinema surround systems typically have limited low frequency response. New digital surround formats now have full-range surround channels that extend frequency response much lower than previous optical surround formats. The SF-1 may be used to protect surround speakers from damage, due to excessive low frequency operation. It is desirable, however, to eventually upgrade the capability of the surround systems to handle the increased power and low frequency response requirements of digital soundtracks.

25

Figure 1

Figure 1 shows where the pertinent switches, resistor networks, and connectors are located on the SF-1 board.

1

CONFIGURATION

SETTING THE SUBSONIC FILTER FREQUENCY

The subsonic (highpass) filter on Channel 1 cannot be bypassed, and Channel 2 should only be bypassed in the bridged mono mode. Plug-in SIP resistor network RN3 sets the high-pass frequency for both channels

1 and 2. Table 2 shows the resistor value to be used for the frequency you desire. Typical subsonic frequencies available with the provided SIP resistor networks are 20, 25, 32, 35, 40, 50, 63, and 80 Hz.

Consult your subwoofer manufacturer if you are unsure of what frequency to use.

If you desire a 6-dB boost at the low end of the subwoofer frequency range, set the slide switch SW1 to “ON”; otherwise set it to “OFF.” Such a boost is popular with users of Electro-Voice B6 subwoofer enclosures.

Frequency

20

25

32

35

40

50

63

80

100

135

160

200

250

TABLE 2

Resistor Network Value (RN3 or RN4)

82K

68K

56K

47K

39K

33K

27K

Factory set for RN3

20K

18K

12K

10K

8.2K

6.8K

Factory set for RN4

SETTING THE SUBWOOFER UPPER FREQUENCY LIMIT

The low-pass filter sets the upper limit of the subwoofer frequency range. Plug-in SIP resistor network RN4 sets the low-pass frequency for both channels 1 and 2. Table 2 shows the resistor value to be used for the frequency you desire. Typical frequencies available with the provided SIP resistor networks are 100, 135,

160, 200, and 250 Hz. Consult your subwoofer manufacturer if you are unsure of what frequency to use.

Whatever frequency you choose should be higher than that of the subsonic filter.

SETTING DIP SWITCH SW2

Determine the configuration you desire and set the DIP switches as described below.

Positions 1 through 4 and 9 and 10

First, decide whether you need “Mono Sum” or “Stereo” operation. This will determine the settings of positions 1 through 4 and 9 and 10 of DIP switch SW2.

• Mono Sum

Because it is difficult for listeners to sense directionality of low audio frequencies, many subwoofer systems are set up for monaural operation, with both channels summed together. For mono summed operation, set the amplifier mode switch to “STEREO” and SW2 as follows:

Position 1

Position 2

Position 3

Position 4

Position 9

Position 10

OFF

ON

ON

OFF

OFF

ON

Continue to “Positions 5 through 8” and set those switches to engage both channels’ low-pass filtering.

2

• Stereo, Bridged Mono, and Parallel Mono

If the two subwoofer channels are to carry different or independent program material, as in stereo or bridged mono, set the SF-1 for “Stereo” operation. Use this also for parallel mono operation from a single program signal source. For stereo, bridged mono, or parallel mono operation, set the amplifier mode switch to “STEREO,” “BRIDGED,” or “PARALLEL,” respectively, and SW2 as follows:

Position 1

Position 2

Position 3

Position 4

Position 9

Position 10

ON

OFF

OFF

ON

ON if bridged mono, OFF otherwise

OFF if bridged mono, ON otherwise

Positions 5 through 8

Next determine whether you wish to bypass the low-pass filtering on either channel for use with a full-range speaker system. This will determine the settings of positions 5 through 8 of DIP switch SW2.

• Channel 1: bypass or engage low-pass?

If you’re connecting a full-range speaker to Channel 1, bypass its low-pass filtering. If you’re connecting it to a subwoofer, engage the filtering. Typical cinema subwoofers are an exception, the low pass filter should be bypassed in this application, as cinema processors typically perform this function.

Position 5

Position 6

ON if bypassed, OFF if engaged

OFF if bypassed, ON if engaged

• Channel 2: bypass or engage low-pass?

Likewise, if you’re connecting a full-range speaker to Channel 2, bypass its low-pass filtering, and if you’re connecting it to a subwoofer, engage the filtering. Typical cinema subwoofers are an exception, the low pass filter should be bypassed in this application, as cinema processors typically perform this function.

Position 7

Position 8

ON if bypassed, OFF if engaged

OFF if bypassed, ON if engaged

CAUTION: On DIP switch SW2, the switch pairs, i.e., positions 1 and 2, 3 and 4, 5 and 6, 7 and 8, and

9 and 10, are complementary. That is, if position 1 is “ON,” 2 must be “OFF” and vice versa; if 3 is

“ON,” 4 must be off, and so on. To prevent improper operation of the SF-1 and the amplifier, and possible damage that may result to the accessory, amplifier, or loudspeaker, check your switch settings carefully before you install the SF-1 in your amplifier.

3

INSTALLATION

Before installing the SF-1, disconnect the amplifier’s power cable from the AC mains.

1. Position the amplifier so that the rear panel is facing you. Locate the input panel and the blank accessory panel above it.

2. Remove the four mounting screws—the two holding the blank panel and the two holding the standard input panel. Remove the blank panel (which the SF-1 will replace) and carefully pull the input panel out from the amplifier chassis (figure 2a).

3. Disconnect the ribbon cable from the circuit board of the input panel.

4. Position the SF-1 so that its component side faces the ribbon connector of the input panel card.

5. Connect the included short ribbon interface cable from the SF-1 to the ribbon connector on the input panel card. The ribbon cable attaches to J4 on the SF-1 (figure 2b).

The connectors are keyed; make sure they line up properly and the ribbon cable is not twisted before you carefully press them together. Be sure to press the connectors together firmly.

6. Connect the ribbon cable from the amplifier (the cable you disconnected from the input panel card) to the SF-1 circuit board, using J3 (figure 2c). Make sure the cable is not twisted; the red stripe on the cable should be toward the right, from your point of view. Newer amplifiers have a keyed connector on the ribbon cable. Press the connectors together firmly.

7. Tuck the interface ribbon cable neatly between the SF-1 and the input panel card. Insert the two cards carefully into the amplifier chassis and secure them with the four screws you removed in step

2. Don’t over-torque the screws (figure 2d).

a b c

Figure 2

4 d

SPECIFICATIONS

SIGNAL TO NOISE RATIO (22 Hz to 22 kHz):

TOTAL HARMONIC DISTORTION

103 dB

<0.1 %

CROSSTALK

CMRR:

FILTER TYPE

70 dB below rated power within passband better than 50 dB second-order butterworth, Q=0.707

(LPF and unboosted subsonic filter) second-order, +6 dB boost, Q=2

(boosted subsonic filter)

DIP SWITCH FUNCTIONS

Mode

Mono Sum

Stereo

Bypass Channel 2 (bridged mono)

Engage Channel 2

Bypass Channel 1 LPF

Bypass Channel 2 LPF

Engage Channel 1 LPF

Engage Channel 2 LPF

TABLE 3—DIP SWITCH SW2

1 2 3 4

OFF ON ON OFF

ON OFF OFF ON

5 6

ON OFF

OFF ON

7 8

ON OFF

OFF ON

9 10

ON OFF

OFF ON

BLOCK DIAGRAM

5

APPLICATION NOTES

For cinema surround channels and subwoofers that do not require an EQ boost, use the following switch settings.

SW1 slide switch- BOOST OFF

SW2 DIP switch

Position 1

Position 2

Position 3

Position 4

Position 5

Position 6

Position 7

Position 8

Position 9

Position 10

ON

OFF

OFF

ON

ON

OFF

ON

OFF

ON if bridged mono, OFF otherwise

OFF if bridged mono, ON otherwise

The high pass filter frequency for non-boosted subwoofers, such as the JBL 4645 and Electro-Voice systems NOT being used in the step-down box tuning mode, should be selected at about 0.8 times the box tuning frequency of the subwoofer. A frequency of 20, 25, or 32 Hz will usually give the best results. Select an appropriate SIP resistor pack and install it in position RN3. Consult your speaker manufacturer for more details about your specific subwoofer system. Surround channels may benefit from the use of a high pass filter at 80 Hz, also installed in position RN3.

For cinema subwoofers that require an EQ boost, use the following switch settings.

SW1 slide switch- BOOST ON

SW2 DIP switch

Position 1

Position 2

Position 3

Position 4

Position 5

Position 6

Position 7

Position 8

Position 9

Position 10

ON

OFF

OFF

ON

ON

OFF

ON

OFF

ON if bridged mono, OFF otherwise

OFF if bridged mono, ON otherwise

The high pass filter frequency for boosted, B6 subwoofer alignments should be selected according to the recommendations of the speaker manufacturer. Select an appropriate SIP resistor pack, for the desired boost frequency, and install it in position RN3. Listed below are some suggested filter frequencies for popular subwoofers, consult your speaker manufacturer for more details about your specific subwoofer system. A variance of +/- 5% from the exact boost frequency will have very little effect on the performance of the system.

Electro-Voice:

TL880D

TL550D

TL3512

TL440

JBL:

4645B

25 Hz

32 Hz

32 Hz

32 Hz

25 Hz

6

APPENDIX A: WARRANTY & DISCLAIMERS

DISCLAIMER

QSC Audio Products, Inc. is not liable for any damage to speakers, amplifiers, or any other equipment that is caused by negligence or improper installation and/or use of the SF-1 Subwoofer Filter.

PRODUCT WARRANTY

QSC Audio Products, Inc. guarantees the SF-1 Subwoofer Filter to be free from defective material and/or workmanship for a period of three years from date of sale, and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use— provided the unit is returned to our factory via prepaid transportation with proof of purchase (sales receipt).

This warranty provides that examination of the returned product must disclose, in our judgment, a manufacturing defect. This warranty does not extend to any product which has been subject to misuse, neglect, accident, improper installation, or where the date code has been removed or defaced.

APPENDIX B: TECHNICAL ASSISTANCE & SERVICE

Servicing your unit requires a trained technician capable of performing the type of service you need. There are no user serviceable components inside your unit and the danger of electric shock exists. Additionally, some of the components in your unit are QSC specific parts that require QSC replacements. Comprehensive service manuals for some models are available at QSC.

TECHNICAL ASSISTANCE

If you suspect that your amplifier is defective, check your system configuration and amplifier settings to determine the origin of the problem. In many cases, incorrect audio interfacing, poor cabling, or other system level impairments are the cause of problems in audio systems. For technical assistance beyond the information given in this manual, the QSC Technical Services department may be contacted.

FACTORY SERVICE

In the event that your amplifier does need factory service, you may reach the QSC Technical Services department for return instructions. A Return Authorization (RA) number must be obtained from the QSC

Technical Services department. QSC may not account for products that are returned without a Return

Authorization number.

Product Return Guidelines

1. Pack the product well for protection during shipment. QSC will provide the factory packaging free of charge upon request.

2. Include a copy of the sales receipt, your name, return address, phone number, and defect description with your return correspondence.

3. Call the QSC Technical Services department for a Return Authorization number.

4. Mark the Return Authorization number on the outside of the packaging.

5. Ship the product prepaid to QSC Audio Products. We recommend United Parcel Service (UPS).

7

QSC TECHNICAL SERVICES DEPARTMENT

1675 MacArthur Blvd

Costa Mesa, CA 92626

Telephone: (800) 772-2834

(714) 957-7150

(714) 754-6175

Fax: (714) 754-6173 Bulletin Board: (714) 668-7567

(800) 856-6003

INTERNATIONAL SERVICING

For QSC products that are purchased outside of the United States, service must be referred to the distributor or dealer from where the product was purchased. There are numerous service centers in many countries.

The service centers in your country may be located by your dealer, distributor, or by contacting QSC

Technical Services.

APPENDIX C: IMPORTANT ADDRESS AND TELEPHONE

INFORMATION

Factory address:

QSC Audio Products, Inc.

1675 MacArthur Boulevard

Costa Mesa, California 92626-1468 USA

Factory telephone numbers:

Main Number

Sales Direct Line

Sales

(714) 754-6175

(714) 957-7100

(800) 854-4079

(toll-free in U.S.A. only)

Sales & Marketing FAX (714) 754-6174

Customer Service

Customer Service

(714) 957-7150

(800) 772-2834

(toll-free in U.S.A. only)

Customer Service FAX (714) 754-6173

QSC OnLine (714) 668-7567

(800) 856-6003

8

11

QSC AUDIO PRODUCTS, INC. 1675 MacArthur Blvd., Costa Mesa, CA 92626 USA Ph (714) 754-6175 Fax (714) 754-6174

Email [email protected] Web http://www.qscaudio.com

“QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office.

12

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement