Quantum M1800 Instruction Manual

Add to my manuals
10 Pages

advertisement

Quantum M1800 Instruction Manual | Manualzz

Introduction

Removing the Library from the Shipping Carton

Removing the Remaining Packing Materials

Checking the Contents

Quantum ATL M1500

Unpacking Instructions

5

10

3

3

Document 6421002-06 A01, July 2003 1

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

2 6207947-04fN 5

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

Introduction

This document explains how to unpack a Quantum ATL M1500. The unpacking procedure consists of the following major steps:

• Removing the library from the shipping carton

• Removing the remaining packing materials

• Checking the contents

Removing the Library from the Shipping Carton

0

To unpack the library:

Note: Be careful not to damage the packaging materials while unpacking the library. Save all packaging materials for possible future use.

1

2

The following tools are required for this operation:

• Scissors

• No. 2 POZIDRIV

® minimum)

screwdriver, long (10 in. or 250 mm

• Antistatic wrist strap

Place the shipping carton and pallet as close to the installation site as possible.

Warning: The shipping carton is secured to the pallet by two plastic straps. The straps are under tension and snap away when cut.

3

4

Using the scissors, carefully cut the two plastic straps securing the

shipping carton to the pallet (see figure 1

).

Lift the lid off of the shipping carton.

0

Introduction 3

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

Figure 1 Removing the

Library from the Shipping

Carton

Lid

Accessories kit

Library

Shipping carton

Pallet

Plastic straps

5

6

Remove the accessories kit and set it aside.

With the help of a second person, lift the library up and out of the shipping carton.

Warning: The library weighs 54 lbs (24.5 kg). At least two people are required to move the library.

Caution: Lift the library by its sides, not by the front bezel.

7 Place the wrapped library on a table or desk.

4 Removing the Library from the Shipping Carton

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

Removing the Remaining Packing Materials

0

Now that you have removed the library from its shipping carton, remove the remaining packing materials from the library:

1

2

Remove the antistatic sheet from the library as follows: a Cut the tape strips securing the sheet.

b c d

Fold the sheet down.

With the help of a second person, lift the library up off of the antistatic sheet.

Place the library on the table or desk next to the antistatic sheet.

Save the antistatic sheet for possible future use.

At the back of the library, remove the handle protection pad.

Caution: The library is equipped with a StackLink cover plate.

Do not remove the StackLink cover plate if the library is a stand-alone unit.

3 If the library will be installed in a rack with a StackLink mechanism, remove the StackLink cover plate from the back of the library using a no. 2 POZIDRIV screwdriver (10 in. or 250 mm long) (see

figure 2 ).

Figure 2 Removing the

Cover Plate

4 Put on an antistatic wrist strap and clip it to the antistatic stud on the back of the library (near the power supply).

Removing the Remaining Packing Materials 5

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

5 Push the button next to the right magazine access door (see

figure 3

).

The right magazine access door opens.

Figure 3 Opening the

Right Magazine Access

Door

Right magazine access door

Button

6 Grasping the handle at the front of the magazine, slide it forward and out of the library (see

figure 4 ).

Figure 4 Removing the

Magazine

Magazine

7 Push the button next to the left magazine access door (see

figure 5 ).

The left magazine access door opens.

6 Removing the Remaining Packing Materials

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

Figure 5 Opening the Left

Magazine Access Door

Figure 6 Magazine

Release Button, Left Side

Only

Button

Left magazine access door

8 Using a slender object such as a pen, press and hold the magazine

release button (see figure 6

).

9

10

Grasping the handle at the front of the left magazine, slide it forward and out of the library.

Use the following steps to remove the two foam pads that stabilize and support the X-Y tray inside the library (see

figure 7 ):

a b

Grasp the tape that secures each foam pad.

Lift the tape and foam pad up and pull towards the door.

Caution: Avoid touching the printed circuit board and its ribbon cable connector. Do not move or remove the foam pad on the robotic hand until instructed to do

so (this occurs during step 13 ).

Removing the Remaining Packing Materials 7

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

Figure 7 Removing the

Foam Pads that Support the X-Y Tray

Left foam pad

Right foam pad

11 Move the robotic hand to the back of the library by reaching through the right magazine access door. Grip the steel flange on the “Y” slide (see

figure 8 ) and push the robotic hand to the back of

the library.

Caution: Avoid touching the printed circuit board and its ribbon cable connector.

8 Removing the Remaining Packing Materials

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

Figure 8 Pushing the

Robotic Hand toward the

Back of the Library

Figure 9 Removing the

Foam Pad from the

Robotic Hand

Steel flange

12 Being careful to touch only the foam pad on the robotic hand, gently rotate the robotic hand 90° counterclockwise until it reaches its limit.

13 Gripping the lower edge of the foam pad, pull to the right and remove it off the robotic hand and out from the library (see

figure 9

).

Pull right and out of the library

Removing the Remaining Packing Materials 9

Quantum ATL M1500 Unpacking Instructions

Document 6421002-06 A01

July 2003

14

15

Replace the left and right magazines.

Close the magazine access doors.

The library is now unpacked and ready to be installed in its final location. Refer to the Quantum ATL M-Series Installation Guide

(6423001) for installation instructions.

Checking the Contents

0

Compare the contents of the shipping carton and the accessories kit with the items listed on the label on the outside of the shipping carton.

If any items are missing or damaged, contact your authorized reseller.

Note: The tape drives and media are sent separately from the library.

10 Checking the Contents

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement