Marvel 3BARM Luxury Series Troubleshooting guide

MARVEL
Installation
Operation
and
Maintenance
Instructions
Beverage and Wine
Refrigerator
Luxury Series
3BARM
6BARM
6OBARM
TABLE OF CONTENTS
Unpacking your refrigerator............................................2
Removing the packaging.............................................2
Warranty Registration...................................................2
Installing your refrigerator...............................................3
Selecting the location..................................................3
Outdoor installation.....................................................3
Cabinet Clearances.....................................................3
Leveling legs...............................................................3
Grounding method......................................................3
Electrical Requirements................................................3
Using Your MicroSentry™ Control...................................4
Dimensions for 3BARM glass door...................................6
Recommended Rough in Opening Dimensions
for 3BARM glass door..................................................6
Dimensions for 3BARM glass overlay door.......................7
Recommended Rough in Opening Dimensions
for 3BARM glass overlay door......................................7
Dimensions for 3BARM solid overlay door....................... 8
Recommended Rough in Opening Dimensions
for 3BARM solid overlay door.......................................8
Dimensions for 6BARM glass door...................................9
Recommended Rough in Opening Dimensions
for 6BARM glass door..................................................9
Dimensions for 6BARM glass overlay door.......................10
Recommended Rough in Opening Dimensions
for 6BARM glass overlay door......................................10
Dimensions for 6BARM solid overlay door...................... .11
Recommended Rough in Opening Dimensions
for 6BARM solid overlay door........................................11
Dimensions for 6OBARM solid door............................... 12
Recommended Rough in Opening Dimensions
for 6OBARM solid door.................................................12
Full Overlay Panel Installation Instructions......................13
3BARM Features.............................................................16
6BARM and 6OBARM Features.......................................17
Care and Cleaning........................................................18
Cleaning condenser air flow........................................18
Cleaning the cabinet...................................................18
Cleaning the interior....................................................18
Cleaning the shelves...................................................18
Cleaning the door gasket............................................18
Replacing the light bulb...............................................18
Troubleshooting Guide...................................................19
Obtaining Service..........................................................20
Household Product Warranty...........................................21
Appendix A additional MicroSentry™ features..................22
1
UNPACKING YOUR BEVERAGE AND WINE REFRIGERATOR
Important Safety Instructions
Warnings and safety instructions appearing in this
guide are not meant to cover all possible conditions and situations that may occur. Common sense,
caution, and care must be exercised when installing,
maintaining, or operating this appliance.
Recognize Safety Symbols,
Words, and Labels.
CAUTION-Hazards or unsafe practices which could
result in personal injury or property or product damage.
WARNING-Hazards or unsafe practices which could
result in personal injury.
NOTE
NOTE-Important information to make a problem free
installation.
Remove Packaging
Your refrigerator has been packed for shipment with
all parts that could be damaged by movement securely
fastened. Cut the banding material at the bottom of the
carton, unfold the cartoning at the bottom and remove
the carton from the appliance. Remove the plastic bag,
styrofoam corner posts and any tape holding the door
closed and internal components in place.
The owners manual is shipped inside the refrigerator in a
plastic bag along with the warranty registration card.
Important
Keep your carton packaging until your refrigerator has
been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed
as proof of damage in transit. Afterwards please dispose
of all items responsibly in particular the plastic bags
which can be a suffocation hazard.
Note to Customer
This merchandise was carefully packed and thoroughly
inspected before leaving our plant. Responsibility for its safe
delivery was assumed by the retailer upon acceptance of the
shipment. Claims for loss or damage sustained in transit
must be made to the retailer.
DO NOT RETURN DAMAGED MERCHANDISE TO THE
MANUFACTURER - FILE THE CLAIM WITH THE RETAILER.
If the unit was shipped or has been laying on its back for
any period of time allow the refrigerator to sit upright for a
period of at least 24 hours before plugging in. This will assure oil returns to the compressor. Plugging the refrigerator
in immediately may cause damage to internal parts.
Warranty Registration
It is important you send in your warranty registration card immediately after taking delivery of your refrigerator or you can
register online at www.marvelrefrigeration.com.
The following information will be required when registering
your unit.
Model Number
Serial Number
Date of Purchase
Dealers name and address
The model number and serial number can be found on the
serial plate which is located inside the refrigerator on the left
side toward the top of the liner.
Help Prevent Tragedies
Child entrapment and suffocation are not problems of the
past. Junked or abandoned refrigerators are still dangerous - even if they sit out for “just a few days”.
If you are getting rid of your old refrigerator, please follow
the instructions below to help prevent accidents.
Before you throw away your old refrigerator or freezer:
• Take off the doors or remove the drawers.
• Leave the shelves in place so children may not easily
climb inside.
2
INSTALLING YOUR BEVERAGE AND WINE REFRIGERATOR
Select Location
The proper location will ensure peak performance of your
appliance. We recommend a location where the unit will
be out of direct sunlight and away from heat sources. To
assure your product performs to specifications the recommended installation location temperature range is from
65 to 80°F (18 to 27°C) for indoor built in units, 65 to
90°F (18 to 32°C) for indoor freestanding units, and 40 to
100°F (4 to 38°C) for outdoor units.
Outdoor Installation
Only the 6OBARM model is suitable for outdoor installations. A ground fault circuit interrupter electrical receptacle
is to be used to supply electrical power to the refrigerator
for outdoor applications. Contact an electrician if you
need to install one to supply electrical power to your outdoor refrigerator. Do not install in an environment where
the unit will be exposed to direct sun exposure as this may
result in unsatisfactory performance.
Cabinet Clearance
Ventilation is required from the bottom front section of the
unit. Keep this area open and clear of any obstructions.
Adjacent cabinets and counter top can be installed around
the unit as long as the grille and door access remain unobstructed.
Front Grille
Do not obstruct the front grille. The openings within the
front grille provide air to flow into and exit from the refrigerator condenser. For this reason it is important this area to
not be obstructed and be kept clean. Marvel does not recommend the use of custom made grilles as air flow may be
restricted because of inadequate openings. (See Figure 1).
Leveling Legs
Adjustable legs at the front and rear corners of the unit
should be set so the unit is firmly positioned on the floor
and level from side to side and front to back. Turn leveling
legs clockwise to raise unit, counterclockwise to lower it.
(See Figure 1).
• Do not splash or spray water from a hose on the
refrigerator. Doing so may cause an electrical shock,
which may result in severe injury or death.
• This unit should not, under any circumstances, be
ungrounded.
Grounding Method
This product is factory equipped with a power supply cord
that has a three-pronged, grounded plug. It must be
plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see Figure 2). If the circuit does
not have a grounding type receptacle, it is the responsibility
and obligation of the customer to exchange the existing
receptacle in accordance with the National Electrical Code
and applicable local codes and ordinances. The third
ground prong should not, under any circumstances, be cut
or removed.
Electrical Connection
115 volts, 3.3 amps running max. 15 amp dedicated circuit
required. 3 prong grounded receptacle required.
Do not use an extension cord
with this appliance.
Front Grille,
keep this
area open.
Figure 2
Figure 1
3
Leveling Legs
USING YOUR MicroSentry™ REFRIGERATOR CONTROL
Door Switch
NOTE
During initial startup, or anytime power is interrupted,
there will be an approximate 5 minute delay before the
refrigerator starts. During this period the controller will
be assessing the temperature in the refrigerator and the
display will appear erratic, this is normal. The desired
temperature set point can be programmed during this
start up period.
Starting your refrigerator
The refrigerator will begin start up when initially plugged in
or when power resumes after a power outage. At this time
the refrigerator will take approximately 5 minutes to begin
running as noted above. If the refrigerator has been turned
off during use, “OFF” will appear on the display. To start
the refrigerator from the “OFF” position press and hold the
ON/OFF button for three seconds.
Set temperature
To set temperature set point, press and continue to hold
“SET” button. After one second, set point will be displayed.
While holding “SET” button use the “WARMER” or “COLDER” button to desired set point.
NOTE: Momentarily pressing & releasing “SET” button will
access information menu of control. Refer to appendix A for
information on this feature.
Refrigerator operation
The available temperature range of the 3BARM refrigerator is 40° to 65° F (4° to 18° C). The available temperature
range for the 6BARM and 6OBARM refrigerators is 39° to
65°F (4° to 18°C).
It may take up to 24 hours for your refrigerator to reach desired temperature. This will depend on amount of contents
loaded and number of openings and closings of the door.
For best results allow refrigerator to “pull down” to desired
set point before loading. Once contents are loaded, allow
at least 48 hours for temperature to stabilize before making any adjustments to the set point.
Alarms
Your MicroSentry™ refrigerator control will monitor refrigerator function and alert you with a series of audible and
visual alarms.
•Door Ajar Alarm: If the door has been left
open for over five (5) minutes, the alarm
will sound in one (1) second intervals. The
display panel will flash “do” and the LED light will be a
Control
Figure 3
steady amber color. This will stop as soon as the door is
closed.
•High and Low Temperature Alarm: If your
unit reaches an unacceptable temperature
outside of your set point, the alarm will
sound in one (1) second intervals. The
display panel will flash either “hi” or “Lo”
depending upon the condition and the LED light will be a
steady amber color. “hi” indicates that the temperature is
10° F (5.5°C) above the set point and “Lo” indicates that
the temperature is 10° F (5.5°C) below the set point. The
alarm will remain active until the condition is corrected.
NOTE: During initial appliance start-up, the high temperature alarm may sound until the interior temperature reaches
set point.
• Temperature Sensor Fault: If the controller
detects that the temperature sensor is
not properly functioning, a temperature
sensor alarm will sound. “E1” will flash on the display, and
an alarm will sound. Please call Marvel Customer Service or
your dealer if this error code is displayed.
• Condenser Needs Cleaning:
When the refrigerator has reached the
recommended amount of run time to necessitate cleaning the air flow, “cL” will flash on the display
as a reminder. See the “Care and Cleaning” section for
cleaning instructions.
To clear the alarm:
1) Press and release the “SET button four times.
“cnd”
will be displayed on the screen.
2) While “cnd” is displayed, press and hold the “SET” button. The display will show the number of weeks the
refrigerator has been running.
3) While holding the “SET” button, press and release the
ON/OFF button. The number shown on the display will
reset to 0.
4) Release the “SET” key.
Alarm Mute
Press any key to mute the audible portion of an alarm,.
NOTE-This action will only mute the alarm. If the condition
4
USING YOUR MicroSentry™ REFRIGERATOR CONTROL
that caused the alarm continues, the alarm code will continue to flash and will sound for 20 seconds every 60 minutes.
Turning Refrigerator Off
To turn refrigerator off, press and hold “ON/OFF” button
for three (3) seconds. “OFF”
display
will appear on the
Additional MicroSentry™ Features
Refer to Appendix A for details on additional features available.
5
DIMENSIONS FOR 3BARM GLASS DOOR
37”
(93.98cm)
16-9/16”
(39.52cm)
25-7/32
(64.06cm)
14-7/8”
(37.78cm)
23-9/32
(59.13cm)
34-1/4” to 34-1/2”
(87 to 87.6 cm)
3” to 3-1/4”
(7.62 to 8.26cm)
21-3/16”
(53.82cm)
Rough In Opening Dimensions, for 3BARM Glass Door
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
34-1/2”
(87.6 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 100 lbs. (45.5 kg.)
*24” (61 cm)
standard cabinet
depth
15” (38.1 cm)
* Depth dimension may vary depending on
each individual installation.
6
DIMENSIONS FOR 3BARM GLASS OVERLAY DOOR
36-27/32
(93.57cm)
13-29/32”
(35.33cm)
23-1/4”
(59.06cm)
14-7/8”
(37.78cm)
22-17/32”
(57.23cm)
34-1/4” to 34-1/2”
(87 to 87.6cm)
3” to 3-1/4”
(7.62 to 8.26cm)
21-3/16”
(53.82cm)
Rough In Opening Dimensions for 3BARM Glass Overlay Door
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
34-1/2”
(87.6 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 100 lbs. (45.5 kg.)
*24” (61 cm)
standard cabinet
depth
15” (38.1 cm)
7
* Depth dimension may vary depending on
each individual installation.
DIMENSIONS FOR 3BARM SOLID OVERLAY DOOR
37-5/32”
(94.39cm)
13-7/8”
(35.26cm)
23-1/4”
(59.06cm)
22-17/32”
(57.23cm)
14-7/8”
(37.78cm)
34-1/4” to 34-1/2”
(87 to 87.6cm)
3” to 3-1/4”
(7.62 to 8.26cm)
21-3/16”
(53.82cm)
Rough In Opening Dimensions for 3BARM Solid Overlay Door
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
34-1/2”
(87.6 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 100 lbs. (45.5 kg.)
*24” (61 cm)
standard cabinet
depth
15” (38.1 cm)
* Depth dimension may vary depending on
each individual installation.
8
DIMENSIONS FOR 6BARM GLASS DOOR
47”
(119.38cm)
25-21/32”
(65.15cm)
26”
(66.04cm)
23-7/8”
(60.66cm)
24-1/16”
(61.1cm)
34-1/4” to 34-1/2”
(87 to 87.6cm)
3” to 3-1/4”
(7.62 to 8.26cm)
22”
(55.88cm)
Rough In Opening Dimensions for 6BARM Glass Door
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
34-1/2”
(87.6 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 130 lbs. (59.1 kg.)
*24” (61 cm)
standard cabinet
depth
24” (61 cm)
9
* Depth dimension may vary depending on
each individual installation.
DIMENSIONS FOR 6BARM GLASS OVERLAY DOOR
46-25/32
(118.82cm)
23-1/32”
(58.5cm)
23-7/8”
(60.66cm)
24-1/16”
(61.1cm)
34-1/4” to 34-1/2”
(87 to 87.6cm)
3” to 3-1/4”
(7.62 to 8.26cm)
22”
(55.88cm)
23-5/16”
(59.21cm)
Rough In Opening Dimensions for 6BARM Glass Overlay Door
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
34-1/2”
(87.6 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 130 lbs. (59.1 kg.)
*24” (61 cm)
standard cabinet
depth
24” (61 cm)
* Depth dimension may vary depending on
each individual installation.
10
DIMENSIONS FOR 6BARM SOLID OVERLAY DOOR
46-27/32”
(119.02cm)
23”
(58.42cm)
23-7/8”
(60.66cm)
24-1/16”
(61.1cm)
34-1/4” to 34-1/2”
(87 to 87.6cm)
3” to 3-1/4”
(7.62 to 8.26cm)
22”
(55.88cm)
23-5/16”
(59.21cm)
Rough In Opening Dimensions for 6BARM Solid Overlay Door
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
34-1/2”
(87.6 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 130 lbs. (59.1 kg.)
*24” (61 cm)
standard cabinet
depth
24” (61 cm)
11
* Depth dimension may vary depending on
each individual installation.
DIMENSIONS FOR 6OBARM SOLID DOOR
47”
(119.38cm)
25-21/32”
(65.15cm)
26”
(66.04cm)
23-7/8”
(60.66cm)
24-1/16”
(61.1cm)
34-1/4” to 34-1/2”
(87 to 87.6cm)
3” to 3-1/4”
(7.62 to 8.26cm)
22”
(55.88cm)
Rough In Opening Dimensions for 6OBARM Solid Door
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
34-1/2”
(87.6 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 130 lbs. (59.1 kg.)
*24” (61 cm)
standard cabinet
depth
24” (61 cm)
* Depth dimension may vary depending on
each individual installation.
12
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 1: Verify door alignment
The door should be parallel to the sides and top of the
refrigerator. If alignment is necessary the door may be
adjusted by loosening the 2 screws which secure the
hinge adapter brackets to the door and adjusting the
door side to side. Use a 5/32” allen wrench for this procedure. (See Figure 4 below).
Top hinge pin
remove to remove
the door.
Hinge adapter screws loosen these to adjust door, on
the top and bottom of the
door
Step 4: Cut overlay panel
Depending on the refrigerator model cut the overlay
panel to the dimensions shown. Use Figure 5 and Table
A for solid door models or use Figure 6 and Table B for
glass door models.
NOTE
For overlay with lock option panel thickness to be
3/4” (19mm) maximum to 5/8” (16mm) minimum.
Weight of the overlay panel should not exceed 20 pounds
(9.1 kilograms).
NOTE
9/32”
(7mm)
For the door closer to work properly it is necessary to
maintain a minimum space of 9/32” (7mm) between the
door and cabinet flange as shown . This space can be
adjusted by adjusting the top and bottom hinge adapters.
W
Front of
overlay
panel
Figure 4
Door must be
parallel to top
and sides of
refrigerator
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8”
allen wrench. Remove the door by angling the top of the
door outward and lifting the door off the bottom hinge.
(See detail in Figure 4).
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it.
Remove the door gasket by peeling up and out of the
channel.
H
Figure 5
Solid Door Models
Model
W
H
3BARM
14-5/8”
(37.13cm)
30-5/16”
(76.99cm)
6BARM
23-5/8”
(59.99cm)
30-5/16”
(76.99cm)
Table A
Solid Door Models
13
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
W
Material Type
#8 Wood Screw
Hardwood
3/32” (2.4mm) Diameter. Pilot Hole
Softwood
5/64 (2.0mm) Diameter. Pilot Hole
Table C
NOTE
1-23/32” Typical 4
(38.77cm) Sides
H
Front of
overlay
panel
If your refrigerator has a door lock proceed to Step 7.
If your refrigerator does not have a door lock proceed
to Step 9.
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the location of the lock
hole on the overlay panel, this is the hole in the top
corner of the handle side of the door. Remove the clamp
and remove the overlay panel from the door. On the
backside of the panel where you marked the lock location
drill a 13/16” (20.5mm) diameter counter bore 7/16”
(11.0mm) deep into the overlay panel. Drill a 15/32”
(12.0mm) diameter hole through the overlay panel centered on the counterbore being careful not to splinter the
wood on the face side of the panel. (See Figure 7).
Figure 6
Glass Door Models
Model
W
H
3BARM
14-5/16”
(36.35cm)
30-5/16”
(76.99cm)
6BARM
23-7/16”
(59.54cm)
30-5/16”
(76.99cm)
Table B
Glass Door Models
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use
the longer extension for a 3/4” thick overlay panel and
the shorter one for a 5/8” thick panel. Assemble the lock
extension, cam stop washer, spring washer, and set screw
to the lock as shown in Figure 7 and 8.
Install this assembly into the overlay panel and secure
with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vertical.
Step 5: Clamp panel to door
Set the overlay panel on the door front, align the edges,
and clamp together. Clamp the panel firmly but be careful not to crush the foam in the door or scratch the door.
Step 6: Drill holes in overlay panel
Remove the hinge adapter bushings from the top and
bottom door hinge adapters. (See Figure 10).Using the
holes in the hinge adapters drill 5/16” (8mm) diameter
clearance holes into the overlay panels 3/4” (20mm)
deep. These will be clearance holes for the top and bottom hinge pins.
Also at this time drill the screw pilot holes for attaching the overlay panel to the door. Select the size of the
hole from Table C. Be careful not to drill the pilot holes
through the overlay panel but only 1/2” (12.7)mm deep.
BRASS EXTENSION
SPRING WASHER
CAM
NUT
LOCK
PHILLIPS SCREW
15/32 HOLE
13/16 COUNTER
BORE 7/16 DEEP
INNER
DOOR
3/4 INCH
WOOD PANEL
SECTION A-A
SCALE 1 : 1
Figure 7
14
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Figure 8
Step 9: Secure overlay panel to the door.
With the #8 wood screws provided fasten the overlay
panel to the door. (See Figure 9).
Step 10: Install lock cam (Models with locks only).
Attach the lock cam to the back of the lock assembly with
the phillips head machine screw provided. Orient the lock
cam vertically when installing on the lock.
Step 11: Install door gasket
Press the door gasket into the door channel. Make
certain the gasket corners are fully inserted. If applicable
insert the key into the lock and make certain the lock
operates properly.
Step 12: Install the door
Install the top and bottom hinge adapter bushings back
into the hinge adapters that were removed in step 6.
Install the door by reversing the procedure from step 2.
Install the top hinge pin so the screw head is flush with
the top surface of the hinge. If applicable insert key into
lock and verify the lock cam works properly with the
catch bracket on the front of the refrigerator cabinet.
Top hinge
Top hinge pin
Top door hinge
adapter
Top hinge adapter
bushing
Bottom door
hinge adapter
Bottom hinge
adapter bushing
Bottom hinge
with cam
Bottom hinge pin
Clearance hole through
door gasket channel
#8 Wood Screw
Figure 10
Right hand
hinges shown
Back of door
Figure 9
15
3BARM BEVERAGE AND WINE REFRIGERATOR FEATURES
Insert Wine Bottles
The wine rack pull-out shelf holds four (4) bottles. See
Figure 4 for typical wine bottle orientation. The wine rack
should be located at the top part of the interior cabinet.
Place the remaining shelves as desired (see Figure 5).
Front Bottles (Necks Facing Rear)
Rear Bottles (Necks Facing Front)
Loading Tips and Suggestions
The two (2) wire racks are for general beverage storage,
such as beer and soft drinks.
Figure 4
You may store magnums and other large bottles on any
of the racks (except for the top rack) by removing the rack
directly above them.
Keep wines that you plan to use for everyday drinking and
entertaining on the front half of the racks where labels are
completely visible. Place wines for aging or longer term
storing in the rear.
Pull-out Racks
The pull-out wine and wire racks may be pulled out approximately seven (7) inches to facilitate adding or removing bottles. Do NOT lean on or press down heavily on the
wine shelf. Doing so may damage the shelf and the wine
bottles stored on it. Pull the wine rack out gently and carefully to minimize unsettling your wine collection. AVOID
pulling out more than one rack at any time to maintain
stability.
Wine shelf
locate at top
of cabinet
Wire shelves
locate as
desired
The bottles on the top rack directly under the light will be
exposed to a slightly higher temperature when the light is
on. Position your wines accordingly and REMEMBER TO
TURN OFF THE LIGHT WHEN IT IS NO LONGER NEEDED.
Single Bottle Racks
Since bottles are not stacked on top of each other, you can
easily view and access your inventory without disturbing
other bottles (see Figure 6).
Figure 5
Figure 6
16
6BARM AND 6OBARM BEVERAGE AND WINE REFRIGERATOR FEATURES
Insert Wine Bottles
The wine rack pull-out shelf holds eight (8) bottles. See
Figure 6 for typical wine bottle orientation. The wine rack
can be located at the middle or bottom part of the interior
cabinet. For red wines, place wine shelf at bottom shelf
position in the cabinet. Then put a glass shelf in the next
higher position. For white and sparkling wines, put the wine
shelf on the middle shelf position in the cabinet. Place the
remaining shelves as desired (see Figure 7). Also, there is a
fixed, wooden, bottle cradle in the bottom, step section of the
cabinet. Six (6) bottles may be stored there.
Loading Tips and Suggestions
The glass and metal shelves and fixed position wire rack are
for general beverage storage, such as beer and soft drinks.
The glass shelf also acts as a zone seperator to create a
warmer zone (5° - 8°F) for wine storage. To cool your wine
to the same temperature as above, the glass can be removed and if necessary replaced with a second metal shelf.
Opened wine bottles and tall beverage containers may be
stored on the black metal shelf closest to the cabinet top, on
the right side where there is clearance for the bottles and/or
containers to stand upright. (See Figure 7).
The wooden, bottom bottle cradle may be removed for storing “jug” wines. Just remove the two (2) screws that secure
the cradle to the cabinet floor.
You may store magnums and other large bottles on any
of the racks (except for the top rack) by removing the rack
directly above them. Position white wines on the middle or
lower racks and red wines on the upper racks (see Figure 8).
Single Bottle Racks
Since bottles are not stacked on top of each other, you can
easily view and access your inventory without disturbing
other bottles (see Figure 8).
Front Bottles (Necks Facing Rear)
Rear Bottles (Necks Facing Front)
Figure 6
Stationary
shelf
Perforated
metal shelf
Glass shelf
Tall bottle
storage
Wine shelf
Wine cradle
The bottles on the top rack directly under the light will be
exposed to a slightly higher temperature when the light is on.
Position your wines accordingly and REMEMBER TO TURN
OFF THE LIGHT WHEN IT IS NO LONGER NEEDED.
Figure 7
Keep wines that you plan to use for everyday drinking and
entertaining on the front half of the racks where labels are
completely visible. Place wines for aging or longer term storing in the rear.
Pull-out Racks
The pull-out wine rack may be pulled out approximately
seven and a half (7.5) inches to facilitate adding or removing
bottles. Do NOT lean on or press down heavily on the wine
shelf. Doing so may damage the shelf and the wine bottles
stored on it. Pull the wine rack out gently and carefully to
minimize unsettling your wine collection. AVOID pulling out
more than one rack at any time to maintain stability.
Figure 8
17
CARE AND CLEANING OF YOUR BEVERAGE AND WINE REFRIGERATOR
Condenser
The condenser tubing inside the cabinet does not require
frequent cleaning; however, satisfactory cooling depends
on adequate ventilation over the coils. Be sure that nothing obstructs the required air flow openings in front of the
cabinet. At least once or twice a year, brush or vacuum lint
and dirt from the front grille area (see page 3).
Cabinet
The painted cabinet can be washed with mild soap and
water and thoroughly rinsed with clear water. NEVER use
abrasive scouring cleaners.
Interior
Wash interior compartment with mild soap and water. Do
NOT use an abrasive cleaner, solvent, polish cleaner or
undiluted detergent.
To replace the light bulb, disconnect power to the unit. Unscrew the old light bulb located behind the display housing
at the top of the unit. Set the old light bulb aside. Screw
the new light bulb into place. Reconnect power to the unit.
Check to see if the light bulb operates properly to complete
the installation.
The light bulb is not covered by your warranty. A replacement bulb can be obtained from your dealer or from
Northland-Marvel.
In the Event of a Power Failure
If a power failure occurs, try to correct it as soon as possible. Minimize the number of door openings while the
power is off so as not to adversely affect the unit’s temperature.
NOTE: If a power interruption occurs, the unit may take 5
to 10 minutes to restart.
Pull-out Racks
The racks may be cleaned with mild soap and water and a
soft cloth. Do NOT use any abrasive cleaners.
Glass Door
Use a glass cleaner or mild soap and water and soft cloth
to clean the glass door model. Do NOT use any abrasive
cleaners.
Door Gasket
The vinyl gasket may be cleaned with mild soap and water,
a baking soda solution or a mild scouring powder.
Light Bulb Replacement
DISCONNECT THE POWER CORD BEFORE ATTEMPTING
LIGHT BULB REPLACEMENT. Failure to do so may result in
an electrical shock that could severely injure you.
The 30WCM and 61WCM use one, 15 watt incandescent
light bulb to illuminate the interior of the refrigerator. The
light bulb is a very reliable electrical component, but should
it not function properly, please call the dealer where you
purchased your refrigerator from for a replacement light
bulb. Use only an original equipment light bulb from your
dealer or Northland-Marvel.
Do NOT under any circumstance use a light bulb that
exceeds 15 watts!
18
TROUBLESHOOTING YOUR BEVERAGE AND WINE REFRIGERATOR
Before You Call for Service
If the unit appears to be malfunctioning, read through this
manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer
to the cause and its remedy before calling for service. The
problem may be something very simple that can be solved
without a service call. Some remedies listed in the Troubleshooting Guide are very complex. Consulting or contracting
a qualified service technician may be necessary.
Electrocution Hazard - Never attempt to repair or perform maintenance on the unit until the main electrical power has
been disconnected.
Problem
Possible Cause
Unit not cold enough
• Control set too warm
Adjust temperatures (See “Set Temperatures” on page 4)
• Airflow to front grille blocked.
• Excessive usage or prolonged
drawer openings.
• Door gasket not sealing properly.
Unit too cold
Remedy
• Adjust temperature colder. Allow 24 hours for temperature to
stabilize.
• Airflow must not be obstructed to
front grille. See “clearances” on
page 3.
• Allow temperature to stabilize for
at least 24 hours.
• Adjust or replace door gasket.
• Control set too cold
• Adjust temperature warmer. (See
page 12, “set the desired temperature”). Allow 24 hours for temperature to stabilize.
No interior light.
• Failed light bulb
• Replace light bulb, see page 18.
Light will not go out when door is
closed
• Door not activating light switch.
• Unit not level, level unit, (See page
3, “leveling legs”)
• Verify the door is aligned properly,
refer to page 13 for instructions.
Noise or Vibration
• Unit not level
• Level unit, see “Leveling Legs” on
page 3.
Unit will not run.
• Unit turned off
• Turn unit on. See “Starting your
refrigerator” on page 4.
• Plug in power cord.
• Check house circuit.
Adjust temperatures (See “Set Temperatures” on page 4)
• Power cord not plugged in.
• No power at outlet.
19
HOW TO OBTAIN SERVICE
If Service is Required:
• If the product is within the first year warranty period
please call Marvel Customer Service at 800.223.3900
for directions on how to obtain warranty coverage in
your area.
• If the product is outside the first year warranty period,
Marvel Customer Service can provide recommendations
of service centers in your area. A listing of authorized
service centers is also available at www.marvelrefrigeration.com under the service and support section.
• In all correspondence regarding service, be sure to give
the model number, serial number, and proof of purchase.
• Try to have information or description of nature of the
problem, how long the unit has been running, the room
temperature, and any additional information that may
be helpful in quickly solving the problem.
• Fill in pertinent information below regarding your product for future reference.
For You Records
Date of Purchase
Dealer’s name
Dealer’s Address
Dealer’s City
Dealer’s State
Dealer’s Zip Code
Appliance Serial Number
Appliance Model Number
Date Warranty Card Sent (Must
be within 10 days of purchase).
20
HOUSEHOLD PRODUCT WARRANTY
Entire Product
Limited One Year Parts and Labor Warranty
Marvel warrants that it will supply all necessary parts and
labor to repair or replace in the end user’s home or office,
any component which proves to be defective in material
or workmanship, subject to the condition and exclusions
stated below, for a period of one year from the date of
purchase by the end user.
Additional Second Through Fifth Year
Limited Parts Only Warranty
During the four years following expiration of the one year
limited warranty, Marvel will supply replacement parts for
the hermetically sealed refrigeration system which consists
of the compressor, condenser, drier, accumulator, bypass
valve, connecting tubing and the evaporator that are
proven to be defective due to workmanship or materials
subject to the conditions and exclusions below.
The above warranties do not cover:
• Shipping costs of replacement parts or returned defective parts.
• Customer education or instructions on how to use the
appliance.
• Any content loss due to product failure.
• Removal or installation of product.
Nor do the above warranties cover failure of this product or
its components due to:
• Transportation or subsequent damages.
• Commercial use or use other than normal household
or small office.
• Improper installation, misuse, abuse, accident or
alteration, use of wiring not conforming to electrical
codes, low or high voltages, failure to provide necessary maintenance, or other unreasonable use.
Parts or Service
Not Supplied or Designated by Marvel
The above warranties also do not apply if:
• The original bill of sale, deliver date, or serial number
cannot be verified.
• Defective parts are not returned for inspection if so
requested by Marvel.
• The refrigeration equipment is not in the possession of
the original end use purchaser.
The warranties set forth herein are the only warranties
extended by Northland-Marvel. Any implied warranties, including the implied warranty of merchantability, are limited
to the duration of these express warranties. In no event
shall Northland-Marvel be liable for any consequential or
incidental damages or expenses resulting from breach of
these or any other warranties, whether express or implied.
Some states do not allow the exclusion or limitation of consequential damages or a limitation on how long an implied
warranty lasts, so the above exclusion or limitation may not
apply to you. This warranty gives you specific legal rights
and you may have other rights that may vary from state to
state.
No person, firm, or corporation is authorized to make any
other warranty or assume any other obligation for Northland-Marvel. These warranties apply only to products used
in any of the fifty states of the United States and the District
of Columbia.
To obtain performance of this warranty, report any defects
to:
Northland-Marvel
P.O. Box 400
1260 E. Van Deinse St.
Greenville MI 48838
Phone: 800.223.3900
21
APPENDIX A, ADDITIONAL MicroSentry™ FEATURES
Information Menu:
The following features are available on the Information
Menu.
•
Current Temperature
•
Maximum Stored Temperature
•
Minimum Stored Temperature
•
Total Operating Time Of The Condenser
•
Keypad Lockout
To access the Information Menu Press “SET” button momentarily and release.
Once in the information menu, the WARMER and COLDER
keys may be used to scroll through the information menu.
Additionally, pressing and releasing the SET key will advance
the information menu.
The information menu will automatically exit after several
seconds with no key presses.
Keypad Lockout Feature (Loc): This feature
is useful for prohibiting changes in the
temperature set point or accidentally turning
the unit off. Press and hold the “SET” key to display the current “Loc” setting. If “No”
is displayed, Lock
out is OFF and all keys are enabled. If “Yes”
is displayed, Lockout is ON and the “ON/OFF”, “WARMER”, and “COLDER” keys are disabled. However, the key
tones remain enabled. While holding the “SET” key, press
the “WARMER” or “COLDER” key to select the desired state.
Release the “SET” key to confirm the selection.
NOTE: The Information/Lockout Key “SET” remains enabled
regardless of the “Loc” setting.
Current Interior Temperature (tI): Press and
hold the “SET” key to display the current interior temperature.
Maximum Stored Temperature (thi): Maximum stored temperature is the maximum
temperature refrigerator has achieved since
temperature set point was entered. Press and hold the “SET”
key to display the maximum temperature stored. The data
can be cleared by pressing “SET” and “ON/OFF” simultaneously while the value is displayed. NOTE: It is normal
for refrigerator temperature to fluctuate from set point by
several degrees.
Minimum Stored Temperature (tLO): Minimum stored temperature is the minimum
temperature refrigerator has achieved since
temperature set point was entered. Press and hold the “SET”
key to display the minimum temperature stored. The data
can be cleared by pressing “SET” and “ON/OFF” simultaneously while the value is displayed. NOTE: It is normal
for refrigerator temperature to fluctuate from set point by
several degrees.
Total Operating Time of the Condenser Since
the Last Cleaning (cnd): Press and hold the
“SET” key to display the total operating hours
of the compressor since the last cleaning. The control stores
the total operating hours of the compressor to determine the
volume of air that has moved across the condenser coils.
This number is displayed in weeks. A reminder is displayed
when a cleaning is recommended (see Alarm Codes). The
recommended cleaning period is the equivalent of one year
of air volume. The data can be cleared by pressing the
“SET” and “ON/OFF” keys simultaneously while the value is
displayed.
22
www.marvelrefrigeration.com
Northland-Marvel
P.O. Box 400
1260 E. Van Deinse St.
Greenville MI 48838
800.223.3900
41011766-EN Rev G
11/21/09
All specifications and product designs subject to change without notice. Such revisions do not entitle
the buyer to corresponding changes, improvements, additions, replacements or compensation for
previously purchased products.