Radio Shack CD-3904 User's Manual

42-6004.fm Page 1 Friday, July 21, 2000 1:18 PM
CD-3904 Portable CD
Please read before using this equipment.
Owner’s Manual
with 10-Second Super Anti-Shock
42-6004.fm Page 2 Friday, July 21, 2000 1:18 PM
ˆ Contents
Features ............................................... 3
Powering the CD Player ......................
Using Batteries .................................
Recharging Nickel-Cadmium
Batteries ......................................
Using AC or DC Power .....................
Connections .........................................
Connecting Earphones or
Headphones .....................................
Listening Safely ...........................
Traffic Safety ................................
Connecting Amplified Speakers .......
Connecting to a Home Audio
System ..............................................
Connecting to an Auto Sound
System ..............................................
5
5
6
6
7
7
7
8
8
8
8
Operation ............................................. 9
Loading a CD .................................... 9
Playing a CD ..................................... 9
Using Super Anti-Shock System
(SAS) .............................................. 10
Using Automatic Search Music
System (ASMS) .............................. 10
Locking the Controls ....................... 10
Using E-Bass .................................. 10
Using Audible Search ..................... 11
Using Intro Scan ............................. 11
Using Repeat Play .......................... 11
Using Random Play ........................ 11
Using Programmed Play ................. 12
Troubleshooting ................................ 13
Care and Maintenance ...................... 14
CD Care Tips .................................. 14
THE FCC WANTS YOU
TO KNOW
This CD player is made and tested to
meet exacting safety standards. It
meets FCC requirements and complies with safety performance standards of the U.S. Department of
Health and Human Services.
Warnings:
• This CD player employs a laser
light beam. Only a qualified service person should remove the
cover or attempt to service this
device, due to possible eye
injury.
• The use of controls, adjustments,
or procedures other than those
specified herein might result in
hazardous radiation exposure.
This equipment complies with the limits for a Class B digital device as
specified in Part 15 of FCC Rules.
These limits provide reasonable protection against radio and TV interference in a residential area. However,
your equipment might cause TV or radio interference, even when it is operating properly.
Specifications .................................... 15
© 2000 RadioShack Corporation.
All Rights Reserved.
RadioShack, RadioShack.com, and Adaptaplug are trademarks used by RadioShack Corporation.
2
42-6004.fm Page 3 Friday, July 21, 2000 1:18 PM
To eliminate interference, you can try
one or more of the following corrective measures:
• use outlets on different electrical
circuits for the equipment and the
radio or TV
• reorient or relocate the receiving
antenna
Consult your local RadioShack store
if the problem still exists.
• increase the distance between
the equipment and the radio or
TV
You must use shielded interface cables with this equipment.
ˆ Features
Your RadioShack Portable CD Player
uses the latest digital audio technology to deliver the clean, crisp sound of
compact discs. You can use optional
stereo earbuds for portable, private
listening, or you can connect the CD
player to your home audio or vehicle’s
sound system using an optional
adapter. The CD player’s other features include:
Auto Power Off — automatically
turns the CD player off 30 seconds after it finishes playing, or when you
press STOP (without pressing another
button), to help preserve battery life.
Super Anti-Shock System — rapidly
scans 10 seconds of data from the
CD and stores it in memory for uninterrupted play with no sound skip,
even when the CD player is exposed
to shocks or vibration. This makes
this CD player excellent for use in
your vehicle.
Eight-Times Over-sampling with
Digital Filtering — improves the
CD’s sound by multiplying the standard 44.1 kHz sample rate by eight
and using a digital filter to reduce or
eliminate distortion.
Programmable Play — lets you program and play up to 20 tracks in any
sequence you choose.
Extended (E-) Bass System — creates a fuller bass sound.
1-Bit DAC — uses the latest in
digital-to-analog conversion circuitry
to accurately reproduce all sound
levels with virtually no distortion.
Intro Scan — scans and plays the
first 10 seconds of each track, so you
can find a specific track.
Repeat Play — lets you automatically
repeat a single track, an entire CD, or
a programmed sequence.
Features
3
42-6004.fm Page 4 Friday, July 21, 2000 1:18 PM
Random Play — lets you randomly
select and play tracks from the loaded
CD in the player.
Hold — prevents accidentally changing the CD player’s control settings
during play and preserves battery life
by locking most controls.
Charge Indicator — lets you monitor
charging status.
Important: You need a pair of stereo
headphones, earphones, or amplified
speakers, or a home audio or auto
sound system to use your CD player.
Your local RadioShack store carries a
complete line of headphones, earphones, speakers, and audio system.
CDs that can be played on this CD
player have this mark on them:
Phones Jack — lets you connect
your CD player to optional headphones, earphones, or speakers.
Line Out Jack and Supplied Y-Cable — make it easy to connect the CD
player to a sound system’s low-level
inputs.
Automatic Search Music System
(ASMS) — lets you quickly locate and
play any track on a CD.
The CD player’s advanced technology makes it simple to operate. However, be sure you read this Owner’s
Manual completely so you can take
advantage of all its advanced features.
Three Power Sources — let you
power your CD player from two standard AA batteries (or special rechargeable Ni-Cd batteries), your
vehicle’s battery using an optional DC
adapter, or standard AC power, using
an optional AC adapter.
Eight-Hour Battery Life — you can
play your CD player for up to 8 hours
on just two fresh alkaline AA batteries
(with the anti-shock feature turned
off).
5- or 3-Inch CD Compatible — you
can play either size CD in your CD
player.
4
Features
42-6004.fm Page 5 Friday, July 21, 2000 1:18 PM
ˆ Powering the CD Player
You can power your CD player from
any of these sources:
• two AA alkaline batteries (not
supplied)
• two rechargeable AA nickelcadmium (Ni-Cd) batteries (not
supplied)
• vehicle battery power using a DC
adapter (not supplied)
• standard AC power using an AC
adapter (not supplied)
Note: The CD player senses whether
or not the batteries you install are rechargeable and turns on the charging
circuit or disconnects the batteries accordingly, provided the correct batteries are installed.
USING BATTERIES
Your CD player can use two AA batteries (not supplied) for power. For
the best performance and longest life,
we recommend RadioShack alkaline
batteries.
You can also use rechargeable Ni-Cd
batteries to power your CD player.
Cautions:
• Use only fresh (or freshly
charged) batteries of the required
size and recommended type.
• Do not mix old and new batteries,
different types of batteries (standard, alkaline, or rechargeable),
or rechargeable batteries of different capacities.
Note: Before you use the CD player
with Ni-Cd batteries, you need to
charge them, either in an external
battery charger (available at your local RadioShack store) or in the CD
player (see “Recharging Nickel-Cadmium Batteries” on Page 6).
Follow these steps to install batteries.
1. Slide the battery compartment
cover in the direction of the arrow
to remove it.
2. Place the batteries in the compartment and on top of the
attached ribbon, as indicated by
the polarity symbols (+ and –)
marked inside.
3. Replace the cover.
When
flashes, the sound becomes weak or distorted, or the CD
player stops operating properly, replace the batteries.
Warning: Dispose of old batteries
promptly and properly. Do not burn or
bury them.
Caution: If you do not plan to use the
CD player with batteries for a month
Powering the CD Player
5
42-6004.fm Page 6 Friday, July 21, 2000 1:18 PM
or longer, remove the batteries. Batteries can leak chemicals that can destroy electronic parts.
Recharging Nickel-Cadmium
Batteries
If you connect an AC or DC adapter
to the CD player (see “Using AC or
DC Power”), you can set the CD player to charge RSU 11672508 Ni-Cd
batteries inside the CD player’s battery compartment.
Cautions:
• Use only an AC or DC adapter
that meets the specifications in
“Using AC or DC Power” to
recharge the batteries in the CD
player. Other adapters could
damage your CD player or the
batteries.
• Ni-Cd batteries charge more efficiently if the temperature is
above 40°F (4.5°C) and below
90°F (32°C).
Follow these steps to charge Ni-Cd
batteries in the CD player.
1. Connect an AC or DC adapter to
your CD player.
2. Place two Ni-Cd batteries in the
compartment and on top of the
attached ribbon, as indicated by
the polarity symbols (+ and –)
marked inside. The CD player
starts to charge the batteries. Ini-
6
tial and subsequent charging
takes about 16 hours.
Note: While charging the
rechargeable Ni-Cd batteries, the
CHARGE indicator lights.
3. When the batteries are fully
charged, disconnect the AC or
DC adapter.
Important: The EPA
certified RBRC® Battery Recycling Seal on a
Ni-Cd battery indicates
RadioShack is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life,
when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Ni-Cd batteries
into the trash or the municipal waste
stream, which may be illegal in your
area. Please call 1-800-THE-SHACK
(1-800-843-7422) for information on
Ni-Cd battery recycling and disposal
bans/restrictions in your area. RadioShack’s involvement in this program is part of the company’s commitment
to
preserving
our
environment and conserving our natural resources.
USING AC OR DC
POWER
You can power the CD player using a
4.5V, 600 mA AC or DC adapter and
a size B Adaptaplug™ connector
Powering the CD Player
42-6004.fm Page 7 Friday, July 21, 2000 1:18 PM
(neither supplied). Both are available
at your local RadioShack store.
Cautions:
from AC power before you disconnect it from the CD player.
Follow these steps to connect the CD
player to AC or DC power.
You must use a (Class
2) power source that
supplies 4.5V DC and
delivers at least 600 mA. Its center tip must be set to positive and
its plug must fit the CD player’s
DC IN 4.5V jack. Using an adapter
that does not meet these specifications could damage the CD
player or the adapter.
!
• Always connect the AC adapter
to the CD player before you connect it to AC power. When you
finish, disconnect the adapter
1. Insert the size B Adaptaplug into
the AC or DC adapter’s cord so it
reads TIP +.
2. Set the adapter’s voltage switch
to 4.5V, as necessary.
3. Insert the barrel plug into the CD
player’s DC IN 4.5V jack.
4. Depending on the type of
adapter you are using, plug the
other end of the adapter into a
standard AC outlet or a 12V
power source.
ˆ Connections
You can listen to your CD player by
connecting optional earphones, headphones, or amplified speakers to the
CD player’s PHONES jack, or by connecting a home audio or vehicle’s
sound system to the CD player’s LINE
OUT jack.
Note: If the jacks on your equipment
do not match the plugs on the supplied Y-cable, check with your local
RadioShack store for the proper cable adapter.
CONNECTING
EARPHONES OR
HEADPHONES
For private listening, connect optional earphones or headphones with a
1
/8-inch (3.5-mm) plug into the
PHONES jack on the CD player.
Listening Safely
To protect your hearing, follow these
guidelines when you use an earphone or headphones.
Connections
7
42-6004.fm Page 8 Friday, July 21, 2000 1:18 PM
• Set the volume to the lowest setting before you begin listening.
After you begin listening, adjust
the volume to a comfortable
level.
• Do not listen at extremely high
volume levels. Extended highvolume listening can lead to permanent hearing loss.
• Once you set the volume, do not
increase it. Over time, your ears
adapt to the volume level, so a
volume level that does not cause
discomfort might still damage
your hearing.
Traffic Safety
Do not wear an earphone or headphones while operating a motor vehicle or riding a bicycle. This can create
a traffic hazard and could be illegal in
some areas.
Even though some earphones or
headphones let you hear some outside sounds when listening at normal
volume levels, they still can present a
traffic hazard.
CONNECTING
AMPLIFIED SPEAKERS
You can listen to your CD player
through amplified speakers. Plug the
speaker cable’s 1/8-inch (3.5-mm)
plug into the CD player’s PHONES
jack.
8
CONNECTING TO A
HOME AUDIO SYSTEM
You can listen to your CD player
through your home audio system’s
amplifier/receiver and full-size speakers. Connect the supplied Y-cable’s
1
/8-inch (3.5-mm) plug to the CD player’s LINE OUT jack. Then connect the
Y-cable’s phono plugs to your audio
system’s left (white) and right (red)
CD, AUX, or TV audio input jacks.
CONNECTING TO AN
AUTO SOUND SYSTEM
You can listen to your CD player
through your vehicle’s sound system
in one of the following ways:
• If your auto sound system has
LINE IN jacks, connect the supplied Y-cable’s 1/8-inch (3.5-mm)
plug to the CD player’s LINE OUT
jack. Then connect the Y-cable’s
phono plugs to your auto sound
system’s LINE IN input jacks.
• If your auto sound system has a
CD input jack, connect one end
of a 1/8-inch (3.5-mm) stereo
patch cable to the CD player’s
LINE OUT jack. Then connect the
other end to your auto sound
system’s CD INPUT jack.
To avoid sound distortion, set VOLUME to the lowest comfortable listening level and adjust it as necessary.
Connections
42-6004.fm Page 9 Friday, July 21, 2000 1:18 PM
Note: You can mount your CD player
in your car using an optional mounting bracket. Your local RadioShack
store has a complete line of mounting
brackets and hardware.
ˆ Operation
LOADING A CD
PLAYING A CD
Caution: To help prevent dust from
entering the CD player, always keep
the CD compartment cover closed,
except when loading or unloading
CDs.
Warning: To protect your hearing if
you are using earphones or headphones, set VOLUME to its lowest setting before you play a CD.
Remove the protective sheet inside
the CD compartment before operating
the CD player.
1. Press OPEN to open the CD
compartment door.
2. Carefully place a CD, label side
up, over the center hub inside the
CD compartment. Then gently
press the CD down over the center hub.
3. Close the compartment cover.
The CD begins to play after -- and
the total track number and play time
appear briefly, if power is on. If power
is not on, press
.
Note: To remove a CD, lift up the CD
while pressing down on the center
hub.
Press
. The CD player automatically turns
on, 10 SEC and the antishock icon appears, then
-- flashes. The total
number of tracks and total play time
appear briefly. Then track 1 begins to
play.
If you connected earphones, headphones, or amplified speakers to the
CD player’s PHONES jack, use VOLUME on the CD player to adjust the
volume.
If you connected the CD player to
your home audio system or vehicle’s
sound system using the LINE OUT
jack, you must use the home audio or
auto sound system’s volume control
to adjust the volume.
To temporarily stop play, press
.
The elapsed time flashes. To resume
play, press
again.
Operation
9
42-6004.fm Page 10 Friday, July 21, 2000 1:18 PM
When the last track finishes playing,
the CD stops and the display shows
the total number of tracks and total
playing time of the CD for about 30
seconds, then the CD player automatically turns off. To turn it off sooner, press .
USING AUTOMATIC
SEARCH MUSIC
SYSTEM (ASMS)
USING SUPER ANTISHOCK SYSTEM (SAS)
You can use ASMS before or during
regular or programmed play to quickly
locate any track on a CD.
Your CD player has a special circuit
to overcome sound skipping problems caused by shock or vibration.
This means you can carry the CD
player anywhere you go, or use it in
your vehicle. When you turn on the
anti-shock system, the CD player
continuously saves 10 seconds of
music in its memory. During a shock
or vibration that would normally make
a track skip or pause, the CD player
plays directly from memory.
The CD player is preset to turn on the
anti-shock system at start up. Repeatedly press SAS to turn anti-shock
on or off. The anti-shock icon appears
when anti-shock is on.
Notes:
• The CD player consumes additional battery power when you
use the anti-shock system. When
you use the CD player in a stable
location, turn off anti-shock to
save battery power.
• When you press SAS to turn antishock on or off, the CD player’s
10
sound briefly cuts out for about 2
seconds.
While the CD is stopped, repeatedly
press
or
to move backward or
forward to the desired track. Press
to play the desired track.
During play, press
to return to the
beginning of the current track. Press
twice to return to the beginning of
the previous track. To move to the beginning of the next track, press
.
LOCKING THE
CONTROLS
You can protect your CD player from
accidental program changes by locking all controls (except E-BASS ON/
OFF, VOLUME, and OPEN).
To lock the controls, slide HOLD to
ON. HOLD appears.
To turn off hold, slide HOLD ON/OFF to
OFF.
USING E-BASS
To enhance the bass sound (when
connecting headphones or external
speakers using the PHONES jack),
Operation
42-6004.fm Page 11 Friday, July 21, 2000 1:18 PM
slide E-BASS ON/OFF to ON. To return
to normal bass sound, slide E-BASS
ON/OFF to OFF.
Note: You can use
or
to skip
through the tracks during scanning.
USING AUDIBLE
SEARCH
USING REPEAT PLAY
To search forward or backward during play, hold down
or
. The
CD plays rapidly and you hear the
sound at a faster speed and lower
volume.
Release
play.
or
When you find the track you want to
play, press
.
to resume normal
Note: If you hold down or
while
the last track is playing, audible
search stops at the end of the last
track. If you hold down
during the
first track, audible search stops at the
beginning of the first track, then begins playing track 1.
USING INTRO SCAN
You can set the CD player to play the
first 10 seconds of each track on the
CD, so you can find the track you
want to listen to.
To begin scanning while a CD is playing, repeatedly press MODE until INTRO flashes. Intro scan starts after
the current track ends.
To begin scanning from the first track,
repeatedly press MODE until INTRO
appears, then press
. Intro scan
starts from the first track.
You can repeat a single track on the
CD, all tracks on the CD, or a programmed sequence (see “Using Programmed Play” on Page 12).
To repeat a single track, press MODE
while the desired track is playing so
appears. The CD player continuously replays the selected track.
To repeat all tracks on a CD or in a
programmed sequence, repeatedly
appears.
press MODE until
When the CD player reaches the end
of the CD or the programmed sequence, it returns to the first track and
replays all the tracks.
To cancel repeat play, repeatedly
or
dispress MODE until
appears.
USING RANDOM PLAY
You can have the CD player randomly play all the tracks (once in random
order), then automatically stop.
To start random play, repeatedly
press MODE until SHUFF appears,
then press
.
Operation
11
42-6004.fm Page 12 Friday, July 21, 2000 1:18 PM
To start random play from the current
track, repeatedly press MODE until
SHUFF appears. Random play begins after the current track ends.
5. To
play
the
programmed
sequence, press
. The first
track in the sequence plays.
While the sequence plays, you
can press
or
to move
backward or forward in the
sequence.
To cancel random play, repeatedly
press MODE until SHUFF disappears.
USING PROGRAMMED
PLAY
You can program up to 20 tracks from
the loaded CD to play in any order
you choose (you can program the
same track to play more than once).
1. While power is on, repeatedly
press PROG. PROG flashes on
the display.
2. Repeatedly press either
or
to display the number of the
first track you want to store.
3. Press PROG again to store the
selected track number and
advance to the next selection
number.
Note: If the CD is playing while
you are programming and you
press
to cancel program
mode, the CD continues play.
6. After the last programmed track
ends, the CD player stops. To
stop the CD sooner, press .
You can replay the programmed sequence within 30 seconds after play
stops. Otherwise, the CD player turns
off and clears the programmed sequence.
To replay the programmed sequence,
press PROG so PROG flashes, then
press
.
To review the programmed track
numbers after programming, press
PROG repeatedly.
To clear the programmed sequence
from memory, press twice or open
the CD compartment cover.
4. Repeat Steps 2 and 3 for each
track you want to store, up to 20
tracks in all.
Note: If you try to store more
than 20 tracks in memory, the CD
player stores each consecutive
track over the first tracks stored.
12
Operation
42-6004.fm Page 13 Friday, July 21, 2000 1:18 PM
ˆ Troubleshooting
If you have problems operating your CD player, try these suggestions. If they do
not solve the problem, contact your local RadioShack service center for assistance.
Problem
The CD player does
not work.
Possible Cause
Solution
The CD Player is set to HOLD.
Slide HOLD in the opposite direction of
the arrow.
No power.
Make sure the batteries are fresh.
Make sure the AC or DC adapter is
properly connected. See “Using AC or
DC Power” on Page 6.
If you are using a DC adapter to power
the DC player, make sure the adapter’s
fuse has not blown.
A CD is loaded, but
the CD player does
not start.
The CD is loaded upside-down.
Reload the CD, label side up.
The CD is dirty or defective.
Clean the CD and reload it, or try a different CD. See “CD Care Tips” on
Page 14.
The CD’s sound
skips.
The CD is dirty or defective.
Clean the CD and reload it, or try a different CD. See “CD Care Tips” on
Page 14.
Vibration is excessive.
Turn on anti-shock. See “Using Super
Anti-Shock System (SAS)” on Page 10.
Place the CD player in a different location.
Moisture has condensed on the
pickup lens.
Troubleshooting
Wait 1 hour for the moisture to evaporate.
13
42-6004.fm Page 14 Friday, July 21, 2000 1:18 PM
ˆ Care and Maintenance
Keep the CD player dry; if it gets wet,
wipe it dry immediately. Use and
store the CD player only in normal
temperature environments. Handle
the CD player carefully; do not drop it.
Keep the CD player away from dust
and dirt, and wipe it with a damp cloth
occasionally to keep it looking new.
case or sleeve when it is not in
use. Fingerprints and scratches
on the CD’s surface can prevent
the laser beam from correctly
reading the digital information. If
the CD gets scratched, use
RadioShack CD repair kit to
repair the disc.
Modifying or tampering with the CD
player’s internal components can
cause a malfunction and might invalidate its warranty. If your CD player is
not performing as it should, take it to
your local RadioShack store for assistance.
• Keep the CD inside the CD
player or in its protective case or
sleeve when you are not playing
it.
CD CARE TIPS
Even though a compact disc is durable, treat the CD surface with care.
• Do not write on either side of the
CD, particularly the non-label
side (signals are read from the
non-label side).
• Never use chemicals such as
record cleaning sprays, antistatic sprays or fluids, benzene,
or thinner to clean CDs. These
chemicals will permanently damage the plastic surface of the CD.
If a CD skips when you try to play it,
the CD might be scratched. Your local
RadioShack store sells a CD repair kit
kit that might stop the skip. See
“Troubleshooting” on Page 13.
• Do not store CDs in high temperature or high humidity areas.
They might warp.
• Keep CDs dry. A water drop can
act as a lens and affect the laser
beam’s focus.
• Always handle a CD by the
edges to avoid fingerprints and
always keep it in its protective
14
Care and Maintenance
42-6004.fm Page 15 Friday, July 21, 2000 1:18 PM
ˆ Specifications
Audio
Frequency Response .............................................................. 20–20,000 Hz (±3 dB)
Dynamic Range ................................................................................................. 80 dB
Signal-to-Noise Ratio ........................................................................................ 80 dB
Harmonic Distortion at 1 kHz ........................................................................... 0.15%
Separation at 1 kHz ........................................................................................... 60 dB
Earphones Output (10% THD at 32Ω) ............................................. 15 mW + 15 mW
Line Output .......................................................................................................... 0.6V
Signal Format
Sampling Frequency .................................................................................... 44.1 kHz
Over sampling ................................................................................................ 8 Times
Quantization Number ................................................................. 1-Bit Linear/Channel
Transmission Bit Rate .................................................................. 4.3218 Mb/Second
Signal-Processing Rate .............................................................................. 352.8 kHz
Pick-Up
Tracking System ........................................................... 3-Beam Tracking Servo Type
Object Lens Drive System ............................................. 2-Dimensional Parallel Drive
Optical Source ............................................................................ Semiconductor Lase
Wavelength ......................................................................................... 785 nm ±25nm
General
Power Requirements ............. DC 3V 2 AA Alkaline or Rechargeable Ni-Cd Batteries
(not supplied)
DC Adapter (not supplied)
AC Adapter (not supplied)
Power Consumption .............................................................................................. 8W
Battery Life (EIAJ Method) ............................................. 8 Hours (with anti-shock off)
Dimensions (HWD) .................................................................. 13/16 × 57/16 × 63/16 in
(30 × 138.5 × 157 mm)
Weight (without batteries) .................................................................................. 8.4 oz
(238g)
Included Accessories ..................................................................................... Y-Cable
Specifications are typical; individual units might vary. Specifications are subject to change
and improvement without notice.
Specifications
15
42-6004.fm Page 16 Friday, July 21, 2000 1:18 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack companyowned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED
WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR
PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN
IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option,
unless otherwise provided by law: (a) correct the defect by product repair without charge for parts
and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the
property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product
made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God,
abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b)
any repairs other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance
costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
RadioShack Corporation
Fort Worth, Texas 76102
12/99
42-6004
07A00
Printed in Hong Kong