OWNER’S MANUAL
We’d like to take a moment to thank you for purchasing the UM-1 (16Channel USB MIDI Interface Cable). This document explains how to set
up the UM-1 system.
To avoid problems and enjoy optimal performance, please carefully
follow the setup instructions described in this document.
201a
Before using this unit, carefully read the sections entitled: “USING
THE UNIT SAFELY” (p. 4) and “IMPORTANT NOTES” (p. 6). These
sections provide important information concerning the proper
operation of the unit. Additionally, in order to feel assured that you
have gained a good grasp of every feature provided by your new
unit, this manual should be read in its entirety. The manual should
be saved and kept on hand as a convenient reference.
202
Copyright © 2000 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced
in any form without the written permission of ROLAND
CORPORATION.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.
*
*
*
*
*
*
*
*
*
*
*
*
*
2
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
Windows® 95 is known officially as: “Microsoft® Windows® 95 operating system.”
Windows® 98 is known officially as: “Microsoft® Windows® 98 operating system.”
Windows® 2000 is known officially as: “Microsoft® Windows® 2000 operating system.”
Windows NT® is known officially as: “Microsoft® Windows NT® operating system.”
Windows® Me is known officially as: “Microsoft® Windows® Millennium Edition operating
system.”
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
MacOS is a trademark of Apple Computer, Inc.
Pentium is a registered trademark of Intel Corporation.
MMX is a trademark of Intel Corporation.
OMS is a registered trademark of Opcode Systems, Inc.
Adobe Acrobat Reader is a trademark of Adobe Systems Incorporated.
All product names mentioned in this document are trademarks or registered trademarks of their
respective owners.
For EU Countries
This product complies with the requirements of European Directive 89/336/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
3
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers
other adverse effects
respect to the home
furnishings, as well
animals or pets.
to damage or
caused with
and all its
to domestic
USING THE UNIT SAFELY 001
•
Before using this unit, make sure to
read the instructions below, and the
Owner’s Manual.
002a
•
Do not open or perform any internal
modifications on the unit.
003
•
Do not attempt to repair the unit, or
replace parts within it (except when this
manual provides specific instructions
directing you to do so). Refer all
servicing to your retailer, the nearest
Roland Service Center, or an authorized
Roland distributor, as listed on the
“Information” page.
4
The
symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
004
•
Never use or store the unit in places
that are:
• Subject to temperature extremes
(e.g., direct sunlight in an enclosed
vehicle, near a heating duct, on top
of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on
wet floors); or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
007
•
Make sure you always have the unit
placed so it is level and sure to remain
stable. Never place it on stands that
could wobble, or on inclined surfaces.
009
•
Do not excessively twist or bend the
USB cable and the MIDI cable, nor place
heavy objects on them. Doing so can
damage the cables.
011
•
Do not allow any objects (e.g.,
flammable material, coins, pins); or
liquids of any kind (water, soft drinks,
etc.) to penetrate the unit.
012d
•
Immediately turn the power off, and
request servicing by your retailer, the
nearest Roland Service Center, or an
authorized Roland distributor, as listed
on the “Information” page when:
• Objects have fallen into, or liquid
has been spilled onto the unit; or
• The unit has been exposed to rain
(or otherwise has become wet); or
• The unit does not appear to operate
normally or exhibits a marked
change in performance.
014
•
Protect the unit from strong impact.
(Do not drop it!)
023
•
DO NOT play a CD-ROM disc on a
conventional audio CD player. The
resulting sound may be of a level that
could cause permanent hearing loss.
Damage to speakers or other system
components may result.
104
•
Try to prevent cords and cables from
becoming entangled. Also, all cords and
cables should be placed so they are out
of the reach of children.
106
•
Never climb on top of, nor place heavy
objects on the unit.
108c
•
Disconnect all cords coming from
external devices before moving the unit.
013
•
In households with small children, an
adult should provide supervision until
the child is capable of following all the
rules essential for the safe operation of
the unit.
5
Important Notes
In addition to the items listed under “USING THE UNIT SAFELY ” on page 4, please read and observe the
following:
Power Supply
•
Before connecting this unit to other devices, turn off the power to all units. This will help prevent malfunctions and/or damage to speakers or other devices.
Placement
• This device may interfere with radio and television reception. Do not use this device in the vicinity of such
receivers.
354a
• Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit.
355
• To avoid possible breakdown, do not use the unit in a wet area, such as an area exposed to rain or other
moisture.
Maintenance
•
For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water.
To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to
wipe the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or
deformation.
Additional Precautions
•
Use a reasonable amount of care when using this unit and its connectors. Rough handling can lead to
malfunctions.
556
• When connecting / disconnecting all cables, grasp the connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s internal elements.
559a
• When you need to transport the unit, package it in the box (including padding) that it came in, if possible.
Otherwise, you will need to use equivalent packaging materials.
6
Handling CD-ROMs
801
•
Avoid touching or scratching the shiny underside (encoded surface) of the disc. Damaged or dirty CD-ROM
discs may not be read properly. Keep your discs clean using a commercially available CD cleaner.
7
Contents
Introduction .............................................................................. 9
Features of the UM-1 ................................................................................ 9
Contents of the Package ......................................................................... 10
Names and Functions............................................................................. 11
Connections ........................................................................... 12
Connections with the MIDI Equipment .............................................. 12
Setting Up Your Computer.................................................... 14
Windows 98 Users .................................................................................. 14
Windows 2000 Users .............................................................................. 17
Macintosh Users...................................................................................... 21
Troubleshooting..................................................................... 27
Windows 98 ............................................................................................. 28
Windows 2000 ......................................................................................... 34
Macintosh................................................................................................. 42
Specifications......................................................................... 44
System Requirements ........................................................... 45
Appendices........................................................................... A-1
For Windows Me Users....................................................................... A-1
8
Introduction
Features of the UM-1
The UM-1 is a USB MIDI interface cable which uses USB as its connection to your computer.
What is USB?
USB stands for Universal Serial Bus, which is a new interface for connecting
various types of peripheral device to computers.
A single USB cable can be used to connect multiple peripheral devices, and data
transmission speed is much faster than the serial port used on previous computers.
In addition, peripheral devices can be connected or disconnected without turning
off the power, and the computer will automatically detect the device which was
connected. (For some peripherals, you may need to make settings or perform other
operations.)
Easy Connection to Your Computer
Connections to your computer can be made even when the power is turned on.
High-Speed Data Transmission via USB
High-speed USB connection provides excellent response even with simultaneous playback
on multiple channels.
Power Supply Not Required
Power is supplied from the computer itself, so a separate power supply is not required.
9
Contents of the Package
The UM-1 package contains the following items. As soon as you open the package, please
verify that all items are present. If any items are missing, please contact the dealer where
you purchased the package.
UM-1 16-Channel USB MIDI Interface Cable
“UM-1 Driver CD-ROM”
* This CD-ROM contains the drivers required for using UM-1, as well as readme files with
additional information.
Labels
You may find it useful to affix these to the cables, to facilitate identification.
UM-1 Owner’s Manual (this document)
10
Names and Functions
2
1
4
3
1
USB Cable
Connect this cable to the USB connector of your computer.
2
TO MIDI IN Cable
Connect this to the MIDI IN connector of the sound module or other device that
you wish to play from your computer.
3
TO MIDI OUT Cable
Connect this to the MIDI OUT connector of the keyboard or other device that
will transmit MIDI messages to your computer.
4
USB Indicator
This indicator will light when the unit is connected to your computer and is
ready to operate.
11
Connections
Here’s how to connect the UM-1 to your computer, a sound module or another MIDI
device.
* This package does not include a MIDI sound module or a MIDI keyboard. You will need to
provide your own, or purchase them separately.
* To prevent malfunction and/or damage to speakers or other devices, always turn down the
volume, and turn off the power on all devices before making any connections
Connections with the MIDI Equipment
Computer
MIDI IN
USB Connector
of your Computer
UM-1
MIDI Equipment (such as SC-88Pro)
MIDI OUT
MIDI Keyboard
* Turn off the power of the computer, MIDI devices, and other peripherals before making
connections.
* Refer to the owner’s manual of your computer and MIDI devices for more information on
setups.
1.
2.
12
Turn off the power of the computer, MIDI devices and the audio playback system to which
you will be making connections.
Connect the UM-1’s TO MIDI IN cable to the MIDI Sound module’s MIDI IN connector.
3.
4.
5.
Use audio cables to connect the MIDI Sound module’s OUTPUT L and R connectors to the
input connectors (INPUT, LINE IN, AUX IN, TAPE IN etc.) of your audio playback system.
* Be sure to connect the MIDI Sound module’s OUTPUT L and R connectors to the L and
R connectors of your audio playback system without reversing the left/right connection. If
L and R are exchanged, the left/right location from which sounds will be heard will be
inverted.
* Never make connections to the MIC connectors or PHONE connectors of your audio
playback system.
If the MIDI Sound module has a Computer switch, set the Computer switch located on the
rear panel of the MIDI Sound module to the “MIDI” position.
* Before changing the setting of the MIDI Sound module’s Computer switch, be sure to turn
off the power.
Connect the MIDI Sound module’s power cable to an electrical outlet.
When you are ready to use the system, turn on the power of the MIDI Sound module
and of your audio playback system.
Connecting a MIDI Keyboard
If you wish to connect a MIDI keyboard, connect the UM-1’s TO MIDI
OUT cable to the MIDI OUT connector of your keyboard.
* Before turning the power off, be sure to turn down the volume of all devices to avoid
speaker damage or malfunctions.
13
Setting Up Your Computer
In order to use the UM-1, you must first install the USB MIDI Driver. The driver is included
in the “UM-1 Driver CD-ROM.”
What is USB MIDI Driver?
The USB MIDI Driver is a software which passes data between the UM-1 and the
application (such as sequencer software) that is running on the USB-connected computer.
The USB MIDI Driver sends data from the application to the UM-1, and passes data from
the UM-1 to the application.
The explanation about installing and setup the driver is organized according to the
computer and MIDI driver that you are using. Please proceed to the following pages.
Windows 98 Users → p. 14
Windows 2000 Users → p. 17
Using OMS on the Macintosh → p. 21
Using FreeMIDI on the Macintosh → p. 25
Windows 98 Users
* The USB MIDI Driver cannot be used with Windows 95 or Windows NT.
* With some computers, starting up Windows with the UM-1 connected can result in
unstable operation. If this happens, you may be able to use the UM-1 by first starting up
Windows with the UM-1 disconnected from the computer, and then afterwards connecting
the UM-1.
* You may be unable to simultaneously use the UM-1 if you have an NEC-manufactured
USB terminal adapter (TA) connected.
* If other programs are running, please exit all of them before you proceed with the
installation.
* If you will be connecting the UM-1 to your computer simultaneously with another Roland
USB-compatible device such as the UA-100, you must disconnect the UA-100 (or other
device) from the USB connector before installing the USB MIDI driver. If you install the
USB MIDI driver while the UA-100 etc. is connected to your computer, the USB MIDI
driver may not be installed correctly.
14
Installing the USB MIDI Driver
1.
2.
3.
4.
5.
Start Windows with all USB cables including the UM-1 (but not the mouse or keyboard)
disconnected.
Exit all applications before performing the installation.
Insert the UM-1 Driver CD-ROM into your CD-ROM drive.
Click the Windows [Start] button, and select “Run...”
When “Run” appears, input the following in the “Open” area.
D:\WIN98\SETUPINF.EXE
6.
7.
8.
9.
10.
11.
* Change the drive name D: to match the drive name of your CD-ROM drive. For example if
your CD-ROM drive is named Q:, you would input “Q:\WIN98\SETUPINF.EXE”.
* If you do not know the name of the drive, click the [Browse] button to check the drive
name.
After inputting the information, click the [OK] button.
* If a message saying that the file was not found appears, check the character string input in
the “Open” area once more.
The “SETUPINF” dialog box will appear, and the display will indicate “Ready to install
driver. ---”
Connect the USB cable of the UM-1 to your computer.
* If the “Add New Hardware Wizard” is displayed, refer to ‘The “Add New Hardware
Wizard” is displayed during the installation procedure.’ (p. 30)
In some cases, the “Insert Disk” dialog box may appear. Click [OK].
The “New Hardware Found” dialog box will appear. In the “Copy files from” area, input
“D:\WIN98” and click the [OK] button. Installation will be completed.
* Change the drive name D: to match the drive name of your CD-ROM drive. For example if
your CD-ROM drive is named Q:, you would input “Q:\WIN98”.
* If this dialog box does not appear, refer to ‘The “Insert Disk” dialog box is not displayed in
“Installing the USB MIDI Driver”.’ (p. 30)
* If you were not able to perform the installation according to this procedure, use the
procedure in “Tried other troubleshooting tips but the UM-1 still does not work” (p. 32) to
delete the driver, and then perform the installation once again.
As described in “Before you begin” (p. 16), make settings so that the UM-1 can be used. The
UM-1 cannot be used unless these settings are made.
15
Before you begin
Before you use the UM-1 with the Windows Media Player
1.
2.
3.
4.
5.
6.
Open “Control Panel,” and find the “Multimedia” icon.
Double-click on “Multimedia” in “Control Panel.”
Click the [MIDI] tab, and in “MIDI Output,” select “1:Roland UM-1 MIDI.”
* If the above “1:Roland UM-1 MIDI” cannot be selected, a problem may have occurred.
Refer to “Troubleshooting.” (p. 27)
Click the [OK] button.
Connect the TO MIDI IN cable of the UM-1 to a MIDI sound module (such as the Roland
SC series).
Start up Windows Media Player or Media Player, select a MIDI file, and play back.
Before you use the UM-1 with an application
In the application(s) that you intend to use, specify the MIDI device they are to use. (For
details on this setting, refer to the owner's manual for your application.)
The MIDI device names and their corresponding cables will be as follows:
MIDI OUT device
Roland UM-1 MIDI --- UM-1 TO MIDI IN cable
MIDI IN device
Roland UM-1 MIDI --- UM-1 TO MIDI OUT cable
* If you are unable to select “Roland UM-1 MIDI” in the MIDI settings of the application,
a problem may have occurred. Refer to “Troubleshooting.” (p. 27)
Changing the settings
To access the settings dialog box, go to “Control panel”–“Multimedia”–“Devices,” and in
“MIDI Devices and Instruments,” select [MIDI for Roland UM-1 MIDI]–“Properties”–
“Settings.”
* Normally, you should leave the “Light Load” check box selected. The setting changes will
take effect after you disconnect, then re-connect the USB cable of the UM-1.
16
Windows 2000 Users
* Only one unit can be used at a time.
* With some computers, starting up Windows with the UM-1 connected can result in
unstable operation. If this happens, you may be able to use the UM-1 by first starting up
Windows with the UM-1 disconnected from the computer, and then afterwards connecting
the UM-1.
* If other programs are running, please exit all of them before you proceed with the
installation.
* If you will be connecting the UM-1 to your computer simultaneously with another Roland
USB-compatible device such as the UA-100, you must disconnect the UA-100 (or other
device) from the USB connector before installing the USB MIDI driver. If you install the
USB MIDI driver while the UA-100 etc. is connected to your computer, the USB MIDI
driver may not be installed correctly.
Installing the USB MIDI Driver
To install the driver, you must log on to Windows as the Administrator or other user with
the privileges of the Administrators group. For more information regarding this, consult
your computer system administrator.
1.
2.
3.
4.
5.
6.
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
Log onto Windows as an Administrator, or other user that is a member of the
Administrators group.
Exit all applications before performing the installation.
Open the “Control Panel,” and double-click “System.”
Click the [Hardware] tab, and then click the [Driver Signing] button. The “Driver Signing
Options” dialog box will appear.
Make sure that “File signature verification” is set to “Ignore.” If it is set to “Ignore,” click
[OK]. If not, make a note of the current setting; then change it to “Ignore” and click the
[OK] button.
* Caution regarding the “File signature verification” setting
• If the “File signature verification” setting is left at “Warn,” the “Digital Signature Not
Found” dialog box will appear during the installation, but you should simply click [Yes]
and continue the installation.
17
7.
8.
9.
10.
• If the “File signature verification” setting is set to “Block,” the “Digital Signature Not
Found” dialog box will appear during the installation; click the [OK] button. “Found
New Hardware Wizard” will appear, so click the [Finish] button to close the wizard,
and re-install as described in ‘Is “? USB Device” shown in “Device Manager”?’ (p. 35)
Click the [OK] button to close “System Properties.”
Insert the UM-1 Driver CD-ROM into your CD-ROM drive.
Click the Windows [Start] button, and select “Run...”
When “Run” appears, input the following in the “Open” area.
D:\WIN2000\SETUPINF.EXE
11.
12.
13.
14.
15.
16.
18
* Change the drive name D: to match the drive name of your CD-ROM drive. For example if
your CD-ROM drive is named Q:, you would input “Q:\WIN2000\SETUPINF.EXE.”
* If you do not know the name of the drive, click the [Browse] button to check the drive
name.
After inputting the information, click the [OK] button.
* If a message saying that the file was not found appears, check the character string input in
the “Open” area once more.
The “SETUPINF” dialog box will appear, and the display will indicate “Ready to install the
driver. ---”
Connect the USB cable of the UM-1 to your computer.
* If in step 6 the “File signature verification” setting is not set to “Ignore,” the “Digital
Signature Not Found” dialog box will appear. If this occurs, refer to “the caution given in
step 6,” and take the appropriate action.
The “Insert Disk” dialog box will appear. Click the [OK] button.
* If this dialog box does not appear, refer to ‘The “Insert Disk” dialog box is not displayed in
“Installing the USB MIDI Driver”.’ (p. 37)
The “Files Needed” dialog box will appear. In the “Copy files from” area, input
“D:\WIN2000” and click the [OK] button.
* Change the drive name D: to match the drive name of your CD-ROM drive. For example if
your CD-ROM drive is named Q:, you would input “Q:\WIN2000. ”
* If you were not able to perform the installation according to this procedure, use the
procedure in “Tried other troubleshooting tips but the UM-1 still does not work” (p. 40) to
delete the driver, and then perform the installation once again.
The “Found New Hardware Wizard” will appear. Make sure that “Roland UM-1 USB
Driver” is displayed, and click the [Finish] button.
17.
18.
19.
The “System Settings Change” dialog box will appear. Click the [Yes] button and re-start
Windows.
If you changed the setting for “Verify file signature” in step 6, set it back to the previous
setting. (To restore the setting, the Administrator or user belonging to the Administrators
group must log on to Windows.)
As described in “Before you begin” (p. 19), make settings so that the UM-1 can be used. The
UM-1 cannot be used unless these settings are made.
Before you begin
Before you use the UM-1 with the Windows Media Player
1.
2.
3.
4.
5.
Double-click “Sounds and Multimedia” in “Control Panel.”
Click the [Audio] tab, and in “MIDI Music Playback,” select “1:Roland UM-1 MIDI.”
* If the above “1:Roland UM-1 MIDI” cannot be selected, a problem may have occurred.
Refer to “Troubleshooting.”(p. 27)
Click the [OK] button to close “Sounds and Multimedia Properties.”
Connect the TO MIDI IN cable of the UM-1 to a MIDI sound module (such as the Roland
SC series).
Open “Windows Media Player,” select a MIDI file, then play back the file.
Before you use the UM-1 with an application
In the application(s) that you intend to use, specify the MIDI device they are to use. (For
details on this setting, refer to the owner's manual for your application.)
The MIDI device names and their corresponding cables will be as follows:
MIDI OUT device
Roland UM-1 MIDI --- UM-1 TO MIDI IN cable
MIDI IN device
Roland UM-1 MIDI --- UM-1 TO MIDI OUT cable
* If you are unable to select “Roland UM-1 MIDI ” in the MIDI settings of the application,
a problem may have occurred. Refer to “Troubleshooting.” (p. 27)
19
To change the settings
To change or verify settings
In order to change the driver settings, you must log on to Windows as the Administrator or
other user in the Administrators group. For more information regarding this, consult your
computer system administrator.
1.
2.
3.
4.
5.
6.
7.
8.
9.
When changing driver settings, always make sure to first quit all applications using the
UM-1. This is unnecessary when only checking the settings.
Open the “Control Panel,” and double-click “System.”
Click the [Hardware] tab, and then click the [Device Manager] button.
Double-click “Sound, video and game controllers.”
Double-click “Roland UM-1 USB Driver.”
Click the [Properties] tab, and in the Multimedia Devices field, double-click “MIDI Devices
and Instruments.”
Select “Roland UM-1 USB Driver,” and click the [Properties] button.
Click the [Settings] button to access the “Roland UM-1 USB Driver Settings” dialog box.
To modify the settings, make the changes and click the [OK] button. To simply check the
settings, be sure to click the [Cancel] button after viewing the settings.
* For details on the setting items, refer to “About the items in the Settings dialog box.” (p. 20)
About the items in the Settings dialog box
The “Light Load” check box
Normally, you should leave the check box cleared.
*The setting changes will take effect after you disconnect, then re-connect the USB cable of
the UM-1.
20
Macintosh Users
Using OMS on the Macintosh
Installing OMS
* If the OMS 2.3.7 or a later version is installed, you do not need to install this version of
OMS. Proceed to the next step and install the USB MIDI Driver.
* Check the version of OMS required for your software. If the software requires later
versions, follow the instructions in the owner’s manual of your software and install OMS.
* Disconnect the USB cable of the UM-1 from your Macintosh before powering up.
1.
2.
3.
4.
5.
Start up your Macintosh.
Insert the UM-1 Driver CD-ROM into the CD-ROM drive.
In the “UM-1 Drivers”–“UM-1-Driver E”–“OMS”–“OMS 2.3.7” folder of the CD-ROM, find
“Install OMS 2.3.7” and double-click the icon.
Follow the on-screen instructions to perform the installation.
After the installation completes, re-start the Macintosh.
Installing the USB MIDI Driver
* The USB MIDI Driver (for OMS) requires Opcode OMS 2.3.5 or later. If this is not
installed, you must first install OMS, and then install the USB MIDI Driver.
* 64 MB or more memory is required. Virtual memory cannot be used. You must make
memory setting to turn virtual memory “off” before using this.
* Disconnect the USB cable of the UM-1 from your Macintosh before powering up.
1.
2.
3.
4.
5.
Start up your Macintosh.
Insert the UM-1 Driver CD-ROM into the CD-ROM drive.
Connect the USB cable to the USB port on your Macintosh. A dialog indicating that the
software cannot be found will appear, but you should simply click [OK].
* If you connect the UM-1 to the USB port on the keyboard of your Macintosh, this message
will appear: “The USB device 'Unknown Device' cannot operate because it needs more
power than is available.” Make sure to connect the UM-1 to a USB connector on the
computer itself.
In the “UM-1 Drivers”–“UM-1 Driver E”–“OMS” of the CD-ROM, double-click the “UM-1
OMS Driver-E Installer” icon.
Follow the on-screen instructions to perform the installation.
21
6.
* If OMS is not correctly installed, the driver installation process will be halted. If this
occurs, exit the driver installation process, and install OMS. After installing OMS, install
the driver once again.
After the installation completes, re-start your Macintosh.
Setting up OMS
* Before setting up OMS, change the setting of the MIDI device connected to the UM-1 to
avoid transmitting the MIDI time clock signal. For instructions on how to change the
setting, refer to the owner’s manual of the MIDI device you have.
* When you install the USB MIDI Driver and set up OMS, two MIDI devices named “Roland
UM-1” will be detected. One of them is the MIDI device connected to the UM-1, and the other
is the UM-1 MIDI interface itself. You need to change the name of the MIDI device connected
to the UM-1 so that the two can be distinguished. Please refer to the next procedures.
1.
2.
3.
4.
5.
Make sure that the UM-1 is connected to your Macintosh, and power up your Macintosh.
In the Opcode folder, open the OMS Applications folder, and double-click the OMS Setup
icon.
If the AppleTalk dialog box appears, select [Turn It Off].
Click [OK] in the dialog box that appears next.
The “Create a New Studio Setup” dialog box will appear. Click [OK].
* If the above dialog box does not appear, select “New Studio Setup” from the File menu.
22
6.
7.
8.
9.
The OMS Driver Search dialog box will appear. Click [Search].
When the search has been completed, make sure that the OMS Driver Setup dialog box lists
the Roland UM-1, and click [OK].
A dialog box will appear, allowing you to save the settings in a file. Input the desired
filename, and click [Save].
The Studio Setup windows will open. Change the device name to “Port 1” for the MIDI
device connected to the UM-1. Click the device name, and you will be able to change it.
Change this device
name to “Port 1”
10.
* Device icons shown in the dialog may be different depending on your setup.
Connect a sound module to the TO MIDI IN cable of the UM-1, select “Test Studio” in the
“Studio” menu, and check it to hear whether sound is produced.
* The following step will cause a relatively loud sound to be produced by the sound module,
so turn down the volume of your sound module before continuing.
23
11.
12.
13.
In the Studio Setup window, place the mouse pointer on the “Port 1” icon, and the pointer
will change to the shape of an eighth note. While the pointer has changed its shape, click
the icon to make sure that sound is produced by the sound module.
* Selecting “Roland UM-1” on the MIDI sequencer software does not generate any sounds
from the sound module connected to the UM-1. Specify “Port 1” to send/receive MIDI
data to/from the equipment connected to the MIDI cable of the UM-1.
* Device icons shown in the dialog may be different depending on your setup.
After verifying that sound is produced from the sound module, select [Quit] from the
“File” menu to exit OMS Setup. A dialog box will appear recommending that you save, so
click [Save].
Re-start your Macintosh.
This completes the setting up OMS.
To learn more about OMS
If you would like to learn more about OMS, please refer to “OMS_2.3_Mac.pdf” (online manual) located in the “UM-1 Drivers”–“UM-1 Driver E”–“OMS”– “OMS 2.3.7”
folder on the CD-ROM. In order to read “OMS_2.3_Mac.pdf,” you will need the
Adobe Acrobat Reader. To install it, double-click “Reader Installer” which is found
in the CD-ROM.
24
Using FreeMIDI on the Macintosh
Installing the USB MIDI Driver
* The USB MIDI Driver (for FreeMIDI) included on the disc is provided as an additional
module that allows the UM-1 to be used with FreeMIDI. Refer to the owner’s manual of
FreeMIDI, and install it on the startup hard disk before installing the USB MIDI Driver.
* 64 MB or more memory is required. Virtual memory cannot be used. You must make
memory settings to turn virtual memory “off” before using this.
* Disconnect the USB cable of the UM-1 from Macintosh before powering up.
1.
2.
3.
4.
5.
6.
Start up the Macintosh.
Insert the UM-1 Driver CD-ROM into the CD-ROM drive.
In the “UM-1 Drivers”–“UM-1 Driver E”–“FreeMIDI,” double-click the “UM-1 FM DriverE Installer” icon.
Follow the on-screen instructions to perform the installation.
After the installation is complete, re-start the Macintosh.
Connect the USB cable of the UM-1 to your Macintosh.
* If you connect the UM-1 to the USB port on the keyboard of your Macintosh, this message
will appear: ‘The USB device “Unknown Device” cannot operate because it needs more
power than is available.’ Make sure to connect the UM-1 to a USB connector on the
computer itself.
Setting up FreeMIDI
1.
2.
3.
4.
Open the “FreeMIDI Applications” folder, and double-click the “FreeMIDI Setup” icon.
* There will be a version number following “FreeMIDI Setup” as the actual icon name.
The first time FreeMIDI is started up, a “Welcome to FreeMIDI!” dialog box will appear.
Click [Continue]. If this is the second or later time, select “FreeMIDI Preferences” from the
File menu.
In the “FreeMIDI Preference” dialog box, check ”UM-1 Port” which is located below UM-1
Driver in MIDI Configuration, and click [OK].
* If the dialog box does not show “UM-1 Driver,” check whether the UM-1 is connected
correctly, and start up FreeMIDI Setup once again.
The About Quick Start dialog box will appear. Click [Continue].
25
5.
6.
7.
8.
9.
26
In the dialog box that appears, select the MIDI equipment that is connected to the UM-1.
Manufacturer
Select the manufacturer of your MIDI equipment. If the appropriate
manufacturer does not appear in the list, select “Other.”
Model
Select the model of your MIDI equipment. If the appropriate model does
not appear in the list, select “Other.”
Click [>>Add>>].
When settings are complete, click [Done].
If you selected “Other” for Model, double-click the appropriate icon in the setting window
to make settings for your MIDI equipment. For details refer to the documentation included
with your software.
From the File menu, select Save, and save your settings.
This completes the setting up FreeMIDI.
Troubleshooting
* Please read the Readme file in the UM-1 Driver CD-ROM. You can get any additional
information not written in the owner’s manual from the Readme file.
Windows 98 Users → p. 28
Windows 2000 Users → p. 34
Macintosh Users → p. 42
Windows 98...............................................................................................................28
Cannot install/uninstall/use the driver ............................................................................ 28
Cannot select the UM-1 device (Roland UM-1 MIDI)...................................................... 30
Cannot play back/record ..................................................................................................... 31
Part of the playback is wrong: e.g., notes are broken off prematurely,
or some notes are lost............................................................................................................ 32
Tried other troubleshooting tips but the UM-1 still does not work
(Uninstalling the USB MIDI Driver) ................................................................................... 32
Windows 2000...........................................................................................................34
Cannot install/uninstall/use the driver ............................................................................ 34
Cannot select the UM-1 device (Roland UM-1 MIDI)...................................................... 37
Cannot play back/record ..................................................................................................... 38
Part of the playback is wrong: e.g., notes are broken off prematurely,
or some notes are lost............................................................................................................ 39
The “Digital Signature Not Found” dialog box appears ................................................. 39
You are asked for the driver file even though it has already been installed ................ 39
Cannot use two or more units simultaneously ................................................................. 40
Other........................................................................................................................................ 40
Tried other troubleshooting tips but the UM-1 still does not work
(Uninstalling the USB MIDI Driver) ................................................................................... 40
Macintosh ..................................................................................................................42
Cannot install the USB MIDI driver ................................................................................... 42
UM-1 is not detected when setting up OMS or FreeMIDI .............................................. 42
No sound ................................................................................................................................ 42
The UM-1 does not recover correctly from sleep mode. ................................................. 43
No sound when testing OMS .............................................................................................. 43
27
Windows 98
Cannot install/uninstall/use the driver
Check with the driver installed on the computer
If you can't use the UM-1 even though you've installed the driver, the driver might not be
installed correctly. Use the following procedure to check.
1.
2.
3.
4.
5.
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
Connect the USB cable of the UM-1 to your computer.
Open the “Control Panel” and double-click “System.”
Click the [Device Manager] tab, and double-click “Sound, video and game controllers.”
Does the display show “Roland UM-1 USB Driver? ”
If this is not displayed, refer to step 5 and following of ‘ Does the “Device Manager” show
“? Composite USB Device,” “? USB Device,” “! USB Device,” or “USB Composite
Device”?’ (p. 28).
If this display appears, but a yellow “!” or red “x” is attached, refer to step 7 and following
of ‘Does the “Device Manager” show a yellow “!” or red “x” for the “Roland UM-1 USB
Driver”?’ (p. 29).
If there is no problem with the display but the UM-1 cannot be used, refer to “Is the UM-1
MIDI device name displayed?” (p. 30).
Does the “Device Manager” show “? Composite USB Device,” “? USB Device,”
“! USB Device,” or “USB Composite Device”?
If the installation was not performed according to the procedure specified in “Installing the
USB MIDI Driver” (p. 15), the UM-1 will not be correctly recognized by Windows, and will
not operate.
Use the following procedure to re-install the driver.
1.
2.
3.
4.
28
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
Connect the USB cable of the UM-1 to your computer.
Open the “Control Panel” and double-click “System.”
Click the [Device Manager] tab.
5.
8.
9.
Check whether “Other devices,” “Sound, video and game controllers,” or “Universal Serial
Bus controllers” contain a line indicating “? Composite USB Device,” “? USB Device,” “!
USB Device,” or “USB Composite Device.”
If you do not find any such item listed in these places, it is likely that the problem is
due to other causes, so please refer to other troubleshooting items.
If you find a line indicating “? Composite USB Device,” “? USB Device,” “! USB Device,” or
“USB Composite Device,” click that line and then click the [Remove] button.
The “Confirm Device Removal” dialog box will appear. Review the contents of the dialog
box, and click the [OK] button.
In the same way, delete every “? Composite USB Device,” “? USB Device,” “! USB
Device,” or “USB Composite Device” that you find.
Disconnect the USB cable of the UM-1.
Re-start Windows.
10.
Install the driver as described in “Installing the USB MIDI Driver.” (p. 15)
6.
7.
Does the “Device Manager” show a yellow “!” or red “x” for the “Roland UM-1
USB Driver”?
Use the following procedure to check.
1.
2.
3.
4.
5.
6.
7.
8.
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
Connect the USB cable of the UM-1 to your computer.
Open the “Control Panel,” and double-click “System.”
Click the [Device Manager] tab.
Double-click “Sound, video and game controllers” to see the list of devices.
In the list, select “Roland UM-1 USB Driver” and check whether a yellow “!” or red “x” are
displayed.
If there is a yellow “!,” exit all applications that are using the UM-1, and then re-connect the
USB cable of the UM-1.
If this does not solve the problem or if a red “x” is displayed, use the procedure described
in “Tried other troubleshooting tips but the UM-1 still does not work” (p. 30) to delete the
driver, and then use the procedure described in “Installing the USB MIDI Driver” (p. 15) to
re-install the driver.
29
Is the UM-1 MIDI device name displayed?
If the device name is not displayed, exit all applications that are using the UM-1, and reconnect the USB cable of the UM-1.
If this does not solve the problem, use the procedure described in “Tried other
troubleshooting tips but the UM-1 still does not work” (p. 30) to delete the driver, and then
use the procedure described in “Installing the USB MIDI Driver” (p. 15) to re-install the
driver.
The “Add New Hardware Wizard” is displayed during the installation procedure.
Use the following procedure to re-install the driver.
1.
2.
3.
4.
Click the [Cancel] button.
Disconnect the USB cable of the UM-1.
Re-start Windows.
Install the driver as described in “Installing the USB MIDI Driver.” (p. 15)
The “Insert Disk” dialog box is not displayed in “Installing the USB MIDI Driver.”
(p. 15)
The following situations are possible.
* Refer to 'Does the “Device Manager” show “? Composite USB Device,” “? USB Device,”
“! USB Device,” or “USB Composite Device”?' (p. 28)
* Refer to ‘Does the “Device Manager” show a yellow “!” or red “x” for the “Roland UM-1
USB Driver”?’ (p. 29)
* Was the driver deleted completely? Delete the driver as described in “Tried other
troubleshooting tips but the UM-1 still does not work” (p. 30), and re-install the
driver as described in “Installing the USB MIDI Driver.” (p. 15)
* Are your computer supplying sufficient current?
If insufficient current is being supplied to the UM-1, connection is not possible.
•The power conservation mode settings of your computer may be limiting the
current supplied to the USB, so check these settings.
Cannot select the UM-1 device (Roland UM-1 MIDI)
Was the driver installed correctly?
Check the driver as described in “Check with the driver installed on the computer.” (p. 28)
30
Did the computer enter a standby or hibernate mode while the UM-1 was
connected?
If the computer entered a standby or hibernate mode while the UM-1 was connected, it may
not operate correctly. In this case, after resuming, exit all applications that are using the
UM-1, and disconnect the USB cable of the UM-1 and re-connect it.
Was the USB cable disconnected and re-connected while the UM-1 was being
used?
If the USB cable is disconnected and re-connected while the UM-1 is in use, it may no longer
operate correctly. If this occurs, exit all applications that are using the UM-1, and
disconnect/re-connect the USB cable of the UM-1.
On some computers, if the UM-1 is connected while Windows starts up, the USB
MIDI Driver will not be loaded correctly, and it will not be possible to use the
UM-1.
If this occurs, start up Windows before you connect the UM-1.
Cannot play back/record
Was the driver installed correctly?
Check the driver as described in “Check with the driver installed on the computer.” (p. 28)
Did you make settings as described in “Before you begin” (p. 16) so that the
UM-1 could be used?
The UM-1 cannot be used unless you make these settings. Refer to “Before you use the
UM-1 with the Windows Media Player” (p. 16) and “Before you use the UM-1 with an
application.” (p. 16)
Could you have entered standby or hibernate mode during playback or
recording?
If you entered standby or hibernate mode during playback or recording, it will no longer be
possible to play back or record from the sound module. Exit all currently playing or
recording applications, and disconnect/re-connect the USB cable of the UM-1.
31
During playback or recording, did you disconnect and re-connect the USB
cable?
If you disconnect and re-connect the USB cable during playback or recording, the UM-1 will
no longer be able to play back or record. Stop playback or recording, and then start
playback or recording once again. If you are still unable to play back or record, quit all
programs that are using the UM-1, then disconnect/re-connect the USB cable of the UM-1.
Part of the playback is wrong: e.g., notes are broken off
prematurely, or some notes are lost
Such problems may be solved if you uncheck the “Light Load” check box. Please refer to
“Changing the settings.” (p. 16)
* The modified setting will take effect after the USB cable of the UM-1 is disconnected and
re-connected. Unless you experience problems, use the checked (initial) setting.
Tried other troubleshooting tips but the UM-1 still does not work
Uninstall the USB MIDI Driver and follow the “Installing the USB MIDI Driver” (p. 15) to
re-install the driver.
Uninstalling the USB MIDI Driver
1.
2.
3.
4.
32
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
Connect the USB cable of the UM-1 to your computer.
Exit all applications before performing the uninstallation.
Delete the driver.
4-1. Open the “Control Panel,” and double-click “System.”
4-2. Click the [Device Manager] tab.
4-3. Double-click “Sound, video and game controllers” to see the list of devices.
4-4. From the list, select “Roland UM-1 USB Driver” and click [Remove].
* If the list does not show “Roland UM-1 USB Driver,” refer to “Cannot
install/uninstall/use the driver.” (p. 28)
4-5. A “Confirm Device Removal” dialog box will appear. Make sure that
“Roland UM-1 USB Driver” is shown in the dialog box, and click the [OK]
button.
4-6. In “System Properties,” click [Close].
5.
6.
7.
Disconnect the USB cable of the UM-1.
Delete the driver settings files.
6-1. Click “Start” → “Settings” → “Folder Options,” and click the [View] tab.
6-2. In “Advanced settings,” uncheck “Hide file extensions for known file types”
and check “Show all files” in “Hidden files.” Then click [OK].
6-3. Click “Start” → “Program” → “Explorer” to start up, and if “Rdif0009.inf” is
in the “\Windows\Inf” folder, select that, then right-click and choose
“Delete” from the menu that appears.
6-4. If “RolandRdif0009.inf” is in the “\Windows\Inf\Other” folder, select that,
then right-click and choose “Delete” from the menu that appears.
6-5. Select “Rdin0009.ini” in the “\Windows” folder, then right-click and choose
“Delete” from the menu that appears.
6-6. In the “\Windows\System” folder, successively “Rddp0009.dat,”
“Rddv0009.drv,” “Rdvx0009.vxd,” and “Rdwm0009.sys,” and for each file,
right-click and choose “Delete” from the menu that appears.
Re-start Windows.
33
Windows 2000
Cannot install/uninstall/use the driver
Are you logged onto Windows with the appropriate user rights?
In order to install/uninstall/re-install drivers, you must be logged onto Windows as an
Administrator, or other user that is a member of the Administrators group. For more
information regarding this, consult your computer system administrator.
Did you make “Driver Signing” settings?
In order to install/re-install drivers, “File signature verification” needs to be carried out.
Use the following procedure to check.
1.
2.
3.
4.
Open the “Control Panel” and double-click “System.”
Click the [Hardware] tab, and then click the [Driver Signing] button. The “Driver Signing
Options” dialog box will appear.
Make sure that “File signature verification” is set to “Ignore.” If it is set to “Ignore,” click
[OK]. If not, make a note of the current setting; then change it to “Ignore” and click the
[OK] button.
* Caution regarding the “File signature verification” setting
• If the “File signature verification” setting is left at “Warn,” the “Digital Signature Not
Found” dialog box will appear during the installation, but you should simply click [Yes]
and continue the installation.
• If the “File signature verification” setting is set to “Block,” the “Digital Signature Not
Found” dialog box will appear during the installation; click the [OK] button. “Found
New Hardware Wizard” will appear, so click the [Finish] button to close the wizard,
and re-install as described in 'Is “? USB Device” shown in “Device Manager”?'(p. 35)
Click the [OK] button to close “System Properties.”
Check with the driver installed on the computer
If you can't use the UM-1 even though you've installed the driver, the driver might not be
installed correctly. Use the following procedure to check.
1.
34
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
2.
3.
4.
Log onto Windows as an Administrator, or other user that is a member of the
Administrators group.
Connect the USB cable of the UM-1 to your computer.
Open the “Control Panel” and double-click on “System.”
5.
6.
7.
Click the [Hardware] tab, and then click the [Device Manager] button.
Double-click “Sound, video and game controllers.”
Does the display show “Roland UM-1 USB Driver”?
* If this is not displayed, refer to 'Is “? USB Device” shown in “Device Manager”?’(p. 35)
* If this display appears, but a yellow “!” or red “x” is attached, refer to 'Does the “Device
Manager” show a yellow “!” or red “x” for the “Roland UM-1 USB Driver”?’ (p. 36)
* If there is no problem with the display but the UM-1 cannot be used, refer to “Is the UM-1
MIDI device name displayed?” (p. 36)
Is “? USB Device” shown in “Device Manager”?
If the installation was not performed according to the procedure specified in “Installing the
USB MIDI Driver” (p. 17), the UM-1 will not be correctly recognized by Windows, and will
not operate. Use the following procedure to re-install the driver.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
Log onto Windows as an Administrator, or other user that is a member of the
Administrators group.
Connect the USB cable of the UM-1 to your computer.
Open the “Control Panel” and double-click on “System.”
Click the [Hardware] tab, and then click the [Device Manager] button.
Check to see if “? USB Device” is displayed under “Other Devices.” If it is not found there,
check if there is a “? USB Device” listed under “Sound, video and game controllers.” If you
do not find any such item listed in these places, it is likely that the problem is due to other
causes, so please refer to other troubleshooting items.
If you find a “? USB Device” line, right-click and then choose “Uninstall” from the menu
that appears.
A “Confirm Device Removal” dialog box will appear. Make sure that “USB Device” is
shown in the dialog box, and click the [OK] button.
Disconnect the USB cable of the UM-1.
Re-start Windows.
35
11.
Install the driver as described in “Installing the USB MIDI Driver” (p. 17)
Does the “Device Manager” show a yellow “!” or red “x” for the “Roland UM-1
USB Driver”?
Use the following procedure to check.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
Log onto Windows as an Administrator, or other user that is a member of the
Administrators group.
Connect the USB cable of the UM-1 to your computer.
Open the “Control Panel” and double-click on “System.”
Click the [Hardware] tab, and then click the [Device Manager] button.
Double-click “Sound, video and game controllers.”
In the list, select “Roland UM-1 USB Driver” and check whether a yellow “!” or red “x” are
displayed.
If there is a yellow “!,” exit all applications that are using the UM-1, and then re-connect the
USB cable of the UM-1.
If this does not solve the problem or if a red “x” is displayed, use the procedure described
in “Tried other troubleshooting tips but the UM-1 still does not work ” (p. 40) to delete the
driver, and then use the procedure described in “Installing the USB MIDI Driver” (p. 17) to
re-install the driver.
Is the UM-1 MIDI device name displayed?
If the device name is not displayed, exit all applications that are using the UM-1, and reconnect the USB cable of the UM-1.
If this does not solve the problem, use the procedure described in “Tried other
troubleshooting tips but the UM-1 still does not work” (p. 40) to delete the driver, and then
use the procedure described in “Installing the USB MIDI Driver” (p. 17) to re-install the
driver.
36
The “Insert Disk” dialog box is not displayed in “Installing the USB MIDI Driver.”
(p. 17)
The following situations are possible.
* Refer to ‘Is “? USB Device” shown in “Device Manager”?’ (p. 35)
* Refer to ‘Does the “Device Manager” show a yellow “!” or red “x” for the “Roland UM-1
USB Driver”?’
* Was the driver deleted completely? Delete the driver as described in “Tried other
troubleshooting tips but the UM-1 still does not work” (p. 40), and re-install the driver as
described in “Installing the USB MIDI Driver.” (p. 17)
* Are your computer supplying sufficient current?
If insufficient current is being supplied to the UM-1, connection is not possible.
•The power conservation mode settings of your computer may be limiting the
current supplied to the USB, so check these settings.
Are two or more UM-1 units connected?
Use the following procedure.
1.
2.
3.
4.
Exit all applications.
Shut down Windows.
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
Connect only one UM-1 unit to your computer, and check the operation.
Cannot select the UM-1 device (Roland UM-1 MIDI)
Was the driver installed correctly?
Check the driver as described in “Check with the driver installed on the computer.” (p. 34)
Did the computer enter a standby or hibernate mode while the UM-1 was
connected?
If the computer entered a standby or hibernate mode while the UM-1 was connected, it may
not operate correctly. In this case, after resuming, exit all applications that are using the
UM-1, and disconnect the USB cable of the UM-1 and re-connect it.
37
Was the USB cable disconnected and re-connected while the UM-1 was being
used?
If the USB cable is disconnected and re-connected while the UM-1 is in use, it may no
longer operate correctly. If this occurs, exit all applications that are using the UM-1, and
disconnect/re-connect the USB cable of the UM-1.
On some computers, if the UM-1 is connected while Windows starts up, the USB
MIDI Driver will not be loaded correctly, and it will not be possible to use the
UM-1.
If this occurs, start up Windows before you connect the UM-1.
Cannot play back/record
Was the driver installed correctly?
Check the driver as described in “Check with the driver installed on the computer.” (p. 34)
Did you make settings as described in “Before you begin” (p. 19) so that the
USB driver could be used?
The UM-1 cannot be used unless you make these settings. Refer to the sections on “Before
you use the UM-1 with the Windows Media Player” (p. 19) and “Before you use the UM-1
with an application.”(p. 19)
Could you have entered standby or hibernate mode during playback or
recording?
If you entered standby or hibernate mode during playback or recording, it will no longer be
possible to play back or record from the sound module. Exit all currently playing or
recording applications, and disconnect/re-connect the USB cable of the UM-1.
During playback or recording, did you disconnect and re-connect the USB
cable?
If you disconnect and re-connect the USB cable during playback or recording, the UM-1 will
no longer be able to play back or record. Stop playback or recording, and then start
playback or recording once again. If you are still unable to play back or record, quit all
programs that are using the UM-1, then disconnect/re-connect the USB cable of the UM-1.
38
Part of the playback is wrong: e.g., notes are broken off
prematurely, or some notes are lost
Such problems may be solved if you check the “Light Load” check box.
If you wish to modify or verify the settings, use the procedure described in “To change or
verify settings.”(p. 20)
* The modified setting will take effect after the USB cable of the UM-1 is disconnected and
re-connected. Unless you experience problems, use the unchecked (initial) setting.
Make the following settings. Performance may be improved.
1.
2.
3.
Double-click on “System” in “Control Panel.”
Click the [Advanced] tab, and then click the [Performance Options] button. Select
“Background services,” and click the [OK] button.
Click the [OK] button to close “System Properties.”
The “Digital Signature Not Found” dialog box appears
If the “Digital Signature Not Found” dialog box appears, refer to ‘Did you make “Driver
Signing” settings?’ (p. 34)
You are asked for the driver file even though it has already
been installed
If you change the USB connector to which the UM-1 is connected, you may be
asked for the driver file.
This is normal behavior, and does not indicate a problem. Use the following procedure to
install the driver.
* If the “Digital Signature Not Found” dialog box appears, refer to "Did you make “Driver
Signing” settings?" (p. 34)
1.
When the “Insert disk” dialog box appears, click the [OK] button.
* If the “Insert disk” dialog box does not appear, but the “Add New Hardware” dialog box
appears, refer to “Are you logged onto Windows with the appropriate user rights?” (p. 34)
39
2.
3.
4.
In the “Copy files from” area, either input the folder that contains the driver, or click the
[Browse] button to access the “Locate File” dialog box, move to the folder that contains the
driver, and click the [Open] button. Then click the [OK] button. (Example: D:\WIN2000)
The “Found New Hardware Wizard” will appear. Make sure that “Roland UM-1 USB
Driver” is displayed, and click the [Finish] button.
The “System Settings Change” dialog box will appear. Click the [Yes] button to re-start the
computer.
If two or more UM-1 units are connected, you may be asked for the driver file.
This driver can be used only for one unit at a time.
When the “Insert disk” dialog box appears, click the [Cancel] button. Then follow the
procedure for “Are two or more UM-1 units connected?” (p. 37)
Cannot use two or more units simultaneously
This driver can be used with only one unit at a time.
The second and subsequent UM-1 cannot be used. Follow the procedure for “Are two or
more UM-1 units connected?” (p. 37)
Other
Display indicates “The currently installed Device Driver does not support Plug
and Play.”
This message may appear if you click the [Resources] tab of “Roland UM-1 USB
Driver Properties.”
Tried other troubleshooting tips but the UM-1 still does not work
To uninstall the driver, you must log on to Windows as the Administrator or other user
belonging to the Administrators group. For more information regarding this, consult your
computer system administrator.
Uninstall the USB MIDI Driver, and follow the “Installing the USB MIDI Driver” (p. 17) to
re-install the driver.
Uninstalling the USB MIDI Driver
1.
40
Start Windows with all USB cables including the UM-1(but not the mouse or keyboard)
disconnected.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Log onto Windows as an Administrator, or other user that is a member of the
Administrators group.
Connect the USB cable of the UM-1 to your computer.
Exit all applications before performing the uninstallation.
Open the “Control Panel” and double-click on “System.”
Click the [Hardware] tab, and then click the [Device Manager] button.
Double-click “Sound, video and game controllers” to see the list of devices.
From the list, right-click “Roland UM-1 USB Driver.” Then choose “Uninstall” from the
menu that appears.
* If the list does not show “Roland UM-1 USB Driver,” refer to “Cannot install/uninstall/
use the driver.”(p. 34)
A “Confirm Device Removal” dialog box will appear. Make sure that “Roland UM-1 USB
Driver” is shown in the dialog box, and click the [OK] button.
Close the “Device Manager,” and in “System Properties” click the [OK] button.
Disconnect the USB cable of the UM-1.
Re-start Windows.
41
Macintosh
Cannot install the USB MIDI driver
Did you exit all other programs?
Exit all currently-running programs.
Cannot install the USB MIDI Driver
Install OMS or FreeMIDI before installing the USB MIDI Driver.
USB MIDI Driver cannot be installed without installing OMS or FreeMIDI first. Refer to the
instruction on the “Installing OMS” (p. 21)or the owner’s manual of your software, and
install OMS or FreeMIDI.
UM-1 is not detected when setting up OMS or FreeMIDI
Was the UM-1 recognized?
• Disconnect the USB cable, and then re-connect it.
• If another USB device is connected, try connecting only the UM-1.
• It is possible that the computer did not correctly recognize or initialize the UM-1.
Leave the USB cable of the UM-1 connected, and re-start your Macintosh. If the
connection is still not achieved, exit your Macintosh and turn off the power of the
computer. Then turn on the power of the computer once again, and start up your
Macintosh.
• The computer cannot recognize the UM-1 when the USB connector of Macintosh’s
keyboard is used. Re-connect the USB cable to the USB connector of the main body.
Are your computer supplying sufficient current?
If insufficient current is being supplied to the UM-1, connection is not possible.
• The power conservation mode settings of your computer may be limiting the current
supplied to the USB, so check these settings.
No sound
Are the USB cable, MIDI cables and audio cables connected correctly?
Refer to “Connections with the MIDI Equipment” (p. 12), and connect the cables correctly.
42
Are the volume controls of your sound module, audio system, and application
raised?
Check each of the volume controls.
Are the sound module settings correct?
Refer to the owner’s manual of your MIDI sound module for more information on settings.
Do you use only OMS?
When installing both FreeMIDI and OMS on your Macintosh, OMS cannot operate
correctly. Delete the files related to FreeMIDI from the “Extensions” folder.
Check the OMS settings
Refer to “Setting up OMS” (p. 22) and check the settings. Make sure that the devices
connected to the UM-1’s TO MIDI OUT/TO MIDI IN cables are selected in the music
application software.
The UM-1 does not recover correctly from sleep mode.
After your Macintosh has been in sleep mode, exit the software and re-start it.
* We recommend that you make Energy saving settings in the Control panel so that your
computer does not enter sleep mode.
No sound when testing OMS
Is the setting of the sound module correct?
Refer to the owner’s manual of your MIDI sound module connected to the computer, and
check with the settings (such as the computer switch).
Are the volume controls of your sound module and the audio system raised?
check each of the volume controls.
Is the Studio Setup valid?
If a diamond (◊) does not appear in the window’s title bar, it means that the Studio Setup is
disabled. Select the “Make Current” from the OMS File menu.
Re-start your Macintosh
Re-start your Macintosh, and check with the settings.
43
Specifications
UM-1: 16-Channel USB MIDI Interface Cable
Cables:
TO MIDI IN/TO MIDI OUT cable (IN x 1, OUT x 1)
USB cable
Power Supply: USB bus-powered (Supplied from Computer)
Current Draw 150mA (during operation)
Dimensions:
89.9 (W) x 52.32 (D) x 18.6 (H) mm
3-9/16 (W) x 2-1/16 (D) x 3/4 (H) inches
Weight:
170 g/6 oz.
Cable Length: TO MIDI IN/TO MIDI OUT cable
USB cable
Accessories:
1200 mm
600 mm
UM-1 Driver CD-ROM
Owner’s Manual
Labels
962a
* In the interest of product improvement, the specifications and/or appearance of this unit
are subject to change without prior notice.
44
System Requirements
Windows
Operating System:
Computer:
CPU/clock:
Memory (RAM):
Microsoft® Windows® 98 (includes Second Edition),
Microsoft® Windows® Me,
Microsoft® Windows® 2000 Professional
Windows 98/Me/2000 Professional compatible computer with a
USB connector conforming to USB specifications Ver.1.1
MMX® Pentium® processor 166 MHz or higher
32 MB or more
(64MB or more for Windows® 2000)
Macintosh
Operating System:
Computer:
CPU/clock:
Memory (RAM):
Mac OS 8.5, 8.6 or 9.x
Apple Macintosh series having USB ports as the standard application
PowerPC G3 233 MHz or higher
64 MB or more
45
Information
EUROPE
EDIROL (Europe) Ltd.
Studio 3.4 114 Power Road
London W4 5PY
U. K.
TEL: +44 (0)20 8747 5949
FAX:+44 (0)20 8747 5948
http://www.edirol.com/europe
Deutschland
TEL: 0700 33 47 65 20
France
TEL: 0810 000 371
Italia
TEL: 02 93778329
When you need repair service, call your nearest EDIROL/Roland Service Center or authorized
EDIROL/Roland distributor in your country as shown below.
HONG KONG
BARBADOS
PERU
IRELAND
CYPRUS
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - Peru
TEL: (511) 4461388
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (022) 66-9426
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
KOREA
NORTH AMERICA
CANADA
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (604) 270 6626
Roland Canada Music Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
AFRICA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
MALAYSIA/
SINGAPORE
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
TEL: (02) 2561 3339
EGYPT
THAILAND
Al Fanny Trading Office
9, EBN Hagar A1 Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
Theera Music Co. , Ltd.
330 Soi Verng NakornKasem,
New Road, Sumpantawongse,
Bangkok 10100, THAILAND
TEL: (02) 224-8821
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
TEL: (010) 6426-5050
Roland Shanghai Electronics
Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie
Yi Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
TEL: (020) 8736-0428
VIETNAM
SAIGON MUSIC
DISTRIBUTOR
(TAN DINH MUSIC)
138 Tran Quang Khai Street
Dist. 1, Ho Chi Minh City
VIETNAM
TEL: (08) 848-4068
AUSTRALIA/
NEW ZEALAND
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
CENTRAL/LATIN
AMERICA
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
TEL: (574)3812529
CURACAO
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
TRINIDAD
AMR Ltd
Ground Floor
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868)638 6385
URUGUAY
Todo Musica S.A.
Francisco Acuna de Figueroa 1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
VENEZUELA
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
DOMINICAN REPUBLIC
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
ECUADOR
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
EUROPE
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021) 285-4169
NORWAY
ISRAEL
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha’aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
POLAND
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
PORTUGAL
KUWAIT
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
ROMANIA
LEBANON
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
TEL: (266) 364 609
Chahine S.A.L.
Gerge Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 165857
Beirut, LEBANON
TEL: (01) 20-1441
RUSSIA
MuTek
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
SPAIN
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
HONDURAS
CZECH REP.
SWEDEN
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
TEL: (2) 666 10529
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
MARTINIQUE
DENMARK
SWITZERLAND
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
FINLAND
UKRAINE
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo,
UKRAINE
TEL: (03131) 414-40
GUATEMALA
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
TEL:(502) 599-2888
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
TEL: (55) 5668-6699
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (505)277-2557
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
IRAN
JORDAN
OMAN
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
QATAR
Badie Studio & Stores
P.O. Box 62,
Doha, QATAR
TEL: 423554
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary
Bldg., 1st Floor, Alkhobar,
SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SYRIA
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
TURKEY
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
MIDDLE EAST
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai,
U.A.E.
TEL: (04) 3360715
BAHRAIN
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 17 211 005
TEL: (23) 511011
As of December 10, 2005 (EDIROL-1)
Appendices
For Windows Me Users
Installing the USB MIDI Driver
1.
2.
3.
4.
5.
6.
7.
Remove all USB cables from the computer (except for the keyboard and mouse), and start
up Windows.
Before installing the driver, quit all applications.
Connect the computer and the device you are using with a USB cable.
The [Add New Hardware Wizard] dialog appears.
Place the CD-ROM provided with your device in the CD-ROM drive.
After a moment, a search is made automatically for the driver, and when detected,
installation of the driver begins.
* If after a few moments nothing appears to be happening, click the [Next] button.
When the dialog announcing that installation of the driver has been completed appears,
click on [Done].
Refer to the following section “Driver Settings” and make the settings for using your
Roland device with your computer. It is these settings that make this possible.
Driver Settings
1.
2.
3.
4.
A-1
From the Windows [Start] menu, select “Control Panels” in “Settings.”
Double-click on the [Sound and Multimedia] icon in “Control Panels.”
* If you cannot find the [Sound and Multimedia] icon, click on “Display all Control Panel
options.” in “Control Panels.
Click on the [Audio] tab in the “Sound and Multimedia Properties” dialog, and select the
item with the name of the device you are using in the “MIDI Music Playback” field.
* If using multiple devices, refer to the Owner’s Manual.
Click on the [OK] button to close “Sound and Multimedia Properties.”
Uninstalling the USB MIDI Driver
1.
Remove all USB cables from the computer (except for the keyboard and mouse), and start
up Windows.
2.
After connecting the computer and the device you are using with a USB cable, turn on the
power to the device. However, the UM-1, UM-2, and UM-4 do not need to be turned on.
Before uninstalling the driver, quit all applications.
From the Windows [Start] menu, select “Control Panels” in “Settings.”
Double-click on the [System] icon in “Control Panels.”
* If you cannot find the [System] icon, click on “Display all Control Panel options.” in
“Control Panels.
Click on the [Device Manager] tab.
Double-click on “Sound, video and game controllers” to display the device list.
Select the name of the device you are using from the list and click on the “Remove” button.
Click on the [OK] button in the “Confirm Device Removal” dialog box.
After confirming that the device name does not appear under “Sound, video and game
controllers,” click on the [Close] button to close “System Properties.”
Disconnect the USB cable from the computer.
Double-click on “Folder Options” in “Control Panels,” then click on the “Display” tab.
Uncheck “Do not display extensions for registered files” in the “Advanced...” items of the
“Display” tab, then click on “Show all files and folders” and click on the [OK] button.
From the Windows [Start] menu, go to “Find” and select “Files and Folders.”
Under “Search in” select “Local Hard Drives” and enter the items as shown below in the
“File or Folder Name” field, the click on the [Find Now] button.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
✽0009.✽
16.
If the following files are among those files found, right-click and select “Remove” from the
menu that appears.
* All may not be display, but this does not indicate any problem.
* No distinction is made between upper- and lower-case letters in the displayed file names.
* Please do not remove any files other than those specified below.
17.
Restart Windows.
Rdif0009.inf, RolandRdif0009.inf, Rddp0009.dat
A-2
Memo
Memo
02678667
1*KG