SERVICE PARTS LIST - Milwaukee Electric Tool

BULLETIN NO.
SERVICE PARTS LIST
54-26-2650
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
REVISED BULLETIN
M18 FUEL™ 1/4" Hex Impact Driver
STARTING
SERIAL NO.
2653-20
CATALOG NO.
WIRING INSTRUCTION
E42A
SEE PAGE 2
IMPORTANT NOTICE!
The original design for the Anvil Assembly (and corresponding
components) are no longer available. Tools manufactured prior
to the serial number E42AD124901722 cannot order individual
parts (2, 3, 4, 5, 10, 11a or 51). Hex Anvil Assembly 42-06-0020
must be ordered. For proper servicing in the future, it is recommended that the nameplate be marked with a '' at the end of
the serial number, using an indelible marker to document this
upgrade*. Tools manufactured after serial number
E42AD124901722 can order all individual anvil parts listed.
IMPORTANT NOTE: Gearcase end cap #25 is
LEFT HAND THREAD!
As an aid to assembly,
carefully lower the complete
front end of tool (gearcase /
impacting system) onto the
gearcase end cap. Gently
hand tighten front end
assembly onto gearcase
end cap. Be careful not
to cross-thread! Once
installed by hand, seat
gearcase end cap with a
good adjustable wrench
using light pressure.
Do not over tighten!
DATE
Mar. 2015
59
2
is recommended to order service name*Itplate
12-20-2653 to record the new serial
65 59
60
number E42AD124901722.
34
47
1
37
LEFT HAND THREAD
35
28
25
12
11a
51
57
1
2
5
4
49
10
46
(2x)
34
62 27
35 36
27
42
43 46
60 28
47 48 50
36
61 19
24
63
58 44
45
10
9
50
(9x)
38
NOTE: Components of the impacting
assembly (61) can drop out of the
24
gearcase (57). Care must be taken to
hold those elements in place when
19(2x)
assembling onto
3 4 5
the gearcase end
64 102 11a
51
cap (25).
51
2 3 4 5 9
56 10
11a 25 51 57
NOTE: Place anvil
spring (51) onto
anvil (11a) with
curled end
inserted in
slot of anvil
as shown.
Place ball (10)
in anvil slot in
front of spring.
45
43
44
Assembly going obsolete. Replaced by:
= 14-20-2654
Electronics Assy.
3
FIG.
1
2
3
4
5
9
10
11a
12
19
24
25
27
28
34
35
36
37
38
42
43
44
45
46
47
48
49
PART NO.
31-12-2653
45-22-0012
34-60-0005
45-88-0022
40-50-0056
45-88-2653
02-02-1100
--------------02-02-1300
02-02-0180
--------------44-66-2653
--------------45-30-2653
--------------23-66-2653
--------------45-24-2653
40-50-1135
40-50-1090
----------------------------06-82-0130
06-82-2653
--------------12-20-2653
42-55-2653
DESCRIPTION OF PART
NO. REQ.
Rubber Cap
(1)
Sleeve
(1)
Retaining Ring
(1)
Washer
(1)
Spring
(1)
Plastic Washer
(1)
4.0mm Steel Ball
(1)
1/4" Hex Anvil
(1)
5mm Steel Ball
(1)
4.7mm Steel Ball
(2)
Ring Gear
(1)
Gearcase End Cap with Ball Bearing (1)
Stator Assembly
(1)
Rubber Slug
(4)
PCBA
(1)
On-Off Switch
(1)
Terminal Block Assembly
(1)
Fwd/Rev Shuttle
(1)
Spring
(1)
Spring
(1)
Left Handle Halve
(1)
Belt Hook
(1)
6-32 x 5/16" Pan Hd. T-15 Machine Scr (1)
M3.5 x 8mm Pan Hd. Plastite Screw
(2)
Right Handle Halve
(1)
Service Nameplate (Not Shown)
(1)
Carrying Case
(1)
FIG.
50
51
56
57
58
59
60
61
62
63
64
65
PART NO.
06-82-7236
40-50-0018
14-30-2653
28-50-2653
42-70-2653
----------------------------14-30-2655
14-20-2653
45-24-2655
42-06-0020
14-46-2653
FIG.
LUBRICATION
(Type 'J' Grease, No. 49-08-4220):
10,11a
DESCRIPTION OF PART
NO. REQ.
4-20 x 5/8" Pan Hd. Plastite T-10 Scr (9)
Anvil Spring
(1)
Gearcase Assembly
(1)
Front Gearcase
(1)
Belt Clip Assembly
(1)
Rotor Assembly
(1)
Handle Assembly
(1)
Impacting Assembly
(1)
Electronics Assembly
(1)
Speed Selector
(1)
1/4" Hex Anvil Assembly
(1)
Rotor/Handle Kit
(1)
Lightly coat front washer surface of anvil (11a) with grease,
place a dab in the ball slot of anvil and in needle bearing
inside the anvil.
24,61
Lightly coat the I.D. of the ring gear (24) and the center of
the planet gears of impacting assembly with grease.
57
Coat inside of bushing inside front gearcase with grease.
59
Coat pinion of rotor assembly (59) with grease.
MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. Lisbon Road, Brookfield, WI 53005
Drwg. 8
LED
ROTOR
STATOR
PCB ASSEMBLY
ON-OFF SWITCH
= WIRE TRAPS
or GUIDES
WIRE TIE
THIS SLEEVE IS
ROUTED OVER THE
RIGHT SIDE OF SWITCH
AS SHOWN.
THIS SLEEVE AND WIRES ARE
ROUTED UNDER THE LEFT SIDE
OF SWITCH AS SHOWN.
AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE
ROUTING AND POSITION IN WIRE GUIDES AND TRAPS
WHILE DISMANTLING TOOL.
BE CAREFUL AND AVOID PINCHING WIRES BETWEEN
HANDLE HALVES WHEN ASSEMBLING.
SPEED SELECTOR
TERMINAL BLOCK
ASSEMBLY