RCA VGM300 User's Guide

VCR User’s Guide

VGM300

We bring good things to life.

i

Introduction

Important Information

WARNING

To reduce the risk of fire or shock hazard, do not expose this VCR to rain or moisture.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates Òdangerous voltageÓ inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Cautions

CAUTIONS: To reduce the risk of electric shock, fully insert plug into socket.

Operate VCR only on 100-240 volts (+/Ð 10%), 50/60 Hz AC power.

¥ It is important that you read and follow the safety information and operating instructions.

¥ Insure that the main supply in your house complies with that indicated on the identification sticker located at the back of your appliance.

¥ Install the VCR horizontally, away from a source of heat ( fireplace) or appliances creating strong magnetic or electric fields (engines).

Follow the drawing below for leaving space around your VCR to insure proper ventilation.

7 cm

10 cm 10 cm 10 cm

7 cm

Side View of VCR

¥ If your VCR or a cassette has been stored in a very cold atmosphere for a certain amount of time, for example during transportation in the winter, wait approximately two hours before using your VCR.

¥ The openings located on the top and the bottom are for ventilation purposes. They should not be obstructed.

¥ In the case of lightning, it is recommended to disconnect the VCR from the external aerial.

¥ By design, this VCR is not for industrial use, but only for domestic operation.

Partial or global recording of copyright protected works made without explicit permission from the copyright holder are illegal.

Introduction

Table of Contents

Important Information

Warnings______________________________ i

Cautions ______________________________ i

Hooking Up the VCR

Choosing a Hookup ____________________ 2

Antenna or Cable System Without a

Cable Box _________________________ 3

Cable System With Cable Box to

Unscramble All Channels ___________ 4

Cable System With Cable Box to

Unscramble Only Pay Channels______ 5

Connecting Two VCRs for Copying Tapes_ 6

Setting Up the VCR

Startup

Check Accessories With VCR ________ 7

Attach Power Cord to Back of VCR ___ 7

Insert Batteries in Remote ___________ 7

Turn on the TV _____________________7

Turn on the VCR ___________________ 8

Select the VCRÕs Output Channel ____ 8

Select the VCRÕs Video System _______ 8

Select the Language/Escoge una

Lengua/Selecione o Idioma________ 8

Place Channels in the VCRÕs

Memory_________________________ 9

Add or Remove Channels from

VCRÕs Memory __________________ 9

Use TV•VCR Button _______________ 10

Set the Time and Date _____________ 10

Using the Remote Control

Controlling a VCR ____________________ 11

Component, VCR, and TV Buttons____ 12-13

Controlling a TV ______________________ 14

Playing a Tape

Operating Instructions

NTSC Video Playback Mode________ 15

Play a Tape_______________________ 15

Using the Playback Features

Auto Head Cleaner________________ 16

Pause for Stop-Action______________ 16

Frame Advance ___________________ 16

Slow Motion______________________ 17

Picture Search ____________________ 17

Digital Auto Tracking _____________ 17

Manual Tracking __________________17

DISPLAY

Button __________________ 18

Time Counter_____________________ 18

Index Search _____________________ 19

Zero Search ______________________ 19

Commercial Scan _________________ 19

Recording a Program

Types of Recordings ___________________ 20

Using the Recording Features

Recording Speeds _________________ 20

Recording Pause __________________ 20

Basic Recording Ð

Operating Instructions _____________ 21

Watch a TV Channel While VCR

is Recording a Different Channel ____ 21

Recording While You're Away

Timer Recording __________________ 22

Select Cable Box or Satellite

Receiver Channel _______________ 23

Check or Clear a

Timer Recording _______________ 23

Timer Recording From the

VCRÕs Line Input _______________ 23

One Touch Recording _________________ 24

Using Two VCRs for Copying

and Editing Tapes _________________ 25

Using Dual Remote with AutoEdit ______ 25

References

Location of Controls

Front Panel_______________________ 26

Back Panel _______________________ 27

Display Panel __________________ 27-28

Specifications _________________________ 29

Cleaning the VCR _____________________ 29

Trouble Checks ____________________ 30-31

Index _____________________________ 32-33

1

2

Hooking Up the VCR

Choosing a Hookup

The hookups on pages 3 through 7 are divided into two hookup types: Basic (A) and

Advanced (B).

The Basic hookup shows the backs of TVs that have only an antenna/cable connection.

It is the easier of the two and additional accessories may not be needed.

The Advanced hookup shows the VCR hooked up to a monitor/receiver

(TV with audio and video jacks). This type of connection may improve the picture quality as well as convenience of operation.

Answer the questions to choose the hookup for your VCR.

1. How do you receive your TV signals?

Choose one answer from below.

A.

Outside antenna Ð Turn to page 3.

B.

Rabbit ears (set-top) and/or bow tie antenna Ð Turn to page 3.

C.

Cable System Ð Go to question 2.

2. What type of Cable-TV system* do you have?

Choose one answer from below.

A.

Cable without a box Ð Turn to page 3.

B.

Cable box to unscramble all the channels Ð Turn to page 4.

C.

Cable box to unscramble only pay channels, such as HBO, Showtime,

Cinemax, etc. Ð Turn to page 5.

*You may need to contact your local cable company for assistance.

Optional Hookups

How to hook up two VCRs for copying tapes?

A.

Select a hookup by answering the questions above.

B.

Then modify the connections as shown on page 6.


Antenna or Cable System Without a Cable Box

A. Basic hookup.

Use this hookup for a simple connection which requires fewer accessories.

A

From Antenna

or Cable

300/75 Ohm

Adapter

1.

Connect as shown.

This connection may require additional accessories not provided.

OR

2.

Plug in power cords of VCR and TV.

IN

OUT

AUDIO VIDEO

IN

OUT

Back of VCR

ANTENNA

IN

OUT

3.

Continue to page 7.

Tune the TV to channel 3 to view the VCR.

RF Coaxial Cable

(supplied)

75 to 75/300 Ohm

Separator

VHF

UHF

OR

Cable/

Antenna

Back of TV

B. Advanced hookup.

Use this hookup for slightly improved picture quality and more convenient operation Ñ use of TV•VCR button not required.

1.


This connection requires additional accessories not provided.

If your TV is stereo, you may need a Y-adapter to hear sound from both channels.

2 . Plug in power cords of VCR and TV.

3.


Tune the TV to its video input to watch the

VCR.

B

From Antenna

or Cable

OR

Signal

Splitter

RF Coaxial Cable

(supplied)

300/75 Ohm

Adapter

Back of VCR

IN

OUT

AUDIO VIDEO

IN

OUT

IN

ANTENNA

OUT

Audio/Video Cables

VIDEO

INPUT

RIGHT

S-VIDEO

OUT AUDIO

L /

MONO

IN

Back of TV

CABLE /

ANTENNA

3


Cable System With Cable Box to Unscramble All Channels



1.



2 . Plug in power cords of VCR, TV, and cable box.

3.



A

From Cable

IN

Cable Box

OUT

RF Coaxial

Cable

Back of VCR

IN

ANTENNA

IN

OUT

AUDIO VIDEO

IN

OUT

OUT

RF Coaxial Cable

(supplied)

75 to 75/300 Ohm

Separator

VHF

UHF

OR

Cable/

Antenna

Back of TV



1 . Connect as shown.




3.



VCR.

B

From Cable

IN

Cable Box

OUT

RF Coaxial

Cable

Signal

Splitter

RF Coaxial

Cable

RF Coaxial Cable

(supplied)

Back of VCR

IN

OUT

AUDIO VIDEO

IN

OUT

IN

ANTENNA

OUT

Audio/Video Cables

VIDEO

INPUT

RIGHT

S-VIDEO

OUT AUDIO

L /

MONO

IN

Back of TV

CABLE /

ANTENNA

Caution: The unauthorized recording of television programs or other materials may infringe the rights of others.

4


Cable System With Cable Box to Unscramble Only Pay Channels

(such as HBO, Showtime, Pay-Per-View, etc.)



A

From Cable

Back of VCR



IN

Cable Box

OUT

RF Coaxial

Cable

IN

ANTENNA


IN

OUT

AUDIO VIDEO

IN

OUT

OUT

3.


RF Coaxial Cable

(supplied)


75 to 75/300 Ohm

Separator

VHF

UHF

OR

Cable/

Antenna

Back of TV







3.



VCR. All pay channels are viewed through the VCR.

B

From Cable

Signal

Splitter

RF Coaxial

Cable

(supplied)

IN

Cable Box

OUT

IN IN

OUT

AUDIO VIDEO

OUT

IN

ANTENNA

OUT

Audio/Video Cables

VIDEO

INPUT

RIGHT

S-VIDEO

OUT AUDIO

L /

MONO

IN

Back of TV

CABLE /

ANTENNA

5


Connecting Two VCRs for Copying Tapes

A

Option A hookup.


1 . Select a hookup from pages 2 through 5 and then modify with this connection.

From Antenna, Cable

or Cable Box

2.

Set the VCR output channel to either channel 3 or 4. See page 8 for details.

You will tune the recording VCR to this channel to receive the signal from the playback VCR.



4 . Plug in power cords of VCRs and TV.

5.


Playback VCR

IN

OUT

AUDIO VIDEO

IN

OUT

Recording VCR

RF Coaxial Cable

(supplied)

IN

OUT

AUDIO VIDEO

IN

OUT

IN

OUT

IN

OUT

ANTENNA

ANTENNA

Audio/Video

Cables

RF Coaxial

Cable

or

Use the previously selected hookup to the TV.

Option B hookup.

Use this hookup for slightly improved copy quality and more convenient operation Ñ use of

TV•VCR button not required.

1 . Select a hookup from pages 2 through 5 and then modify with this connection.




3 . Plug in power cords of VCRs and TV.

4.


Select the line (audio/video) input on the recording VCR to receive the signal from the playback VCR.

B

Caution: The unauthorized recording of television programs or other materials may infringe the rights of others.

Playback VCR (only)

ANTENNA

IN

IN

OUT

AUDIO VIDEO

IN

OUT

OUT

Audio/Video

Cables

IN

OUT

AUDIO VIDEO

OUT

IN

Recording VCR

ANTENNA

From Antenna, Cable

or Cable Box

IN

OUT

Audio/Video

Cables

RF Coaxial Cable

(supplied)

or

Use the previously selected hookup to the TV.

6

Setting Up the VCR

Startup

1.

Check accessories with VCR.

Contact your dealer if any items are missing.

POW

ER VCR1

VCR2•LD

TV

REW

REC

DISPLAY

PLAY FF

STOP

CHAN

PAUSE

SEARCH

MUTE

1

4

CHAN

2

5

3

6

PREV CH

7 8

INPUT

0

9

TV•VCR

CLEAR

F.ADV

SLOW +

MENU

* PROG SPEED

EDIT

TRACKING

4

2 “AAA” Batteries RF Coaxial Cable

(Stock No. 221407)

Remote

(Stock No. 221406)

2.

Attach power cord to back of VCR.

1st 2nd

Power Cord

(Stock No. 221408)

3.

Insert batteries in remote.

4.

Turn on the TV.

A.

Turn on the TV.

B . If you used one of the basic hookups, tune the TV to channel 3.

If you used one of the advanced hookups, tune the TV to the TVÕs video input. (See TV ownerÕs manual for details.) continued on next page

7


Startup

5.

Turn on the VCR.

Press VCR1 on the remote.

6.

Select the VCR’s output channel.

A . Press VCR1 on the remote.

B . Press MENU•PROG on the remote to see the VCR MAIN MENU on the TV screen.

C . Press 4 to display the PREFERENCES menu.

D . Press 3 to select either 3 or 4 as the output channel for your

VCR. This is the channel to which you tune your TV to see the picture from the VCR.

¥ If you select Output Channel: 3, you will view the VCRÕs output on channel 3 of your TV.

¥ If you select Output Channel: 4, you will view the VCRÕs output on channel 4 of your TV.

If you change the output channel, remember to tune your TV to the channel you selected (3 or 4) to watch the VCR.

7.

Select the VCR’s video system.



C . Press 4 to display the PREFERENCES menu.

D . Press 4 to select the type of video that is broadcast in your area.

¥ Select Video System: AUTO to have the VCR automatically select the type of video.

¥ Select Video System: PAL if PAL video is broadcast in your area.

¥ Select Video System: NTSC if NTSC video is broadcast in your area.

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

4 Preferences

PREFERENCES

1 Remote Control: VCR1

2 Front Panel: AUTO

3 Output Channel: 3

4 Video System: AUTO

5 Play NTSC as: NTSC

0 Exit

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

4 Preferences

PREFERENCES


2 Front Panel: AUTO

3 Output Channel: 3



0 Exit

8. Select the language/Escoge una lengua/Selecione o idioma.

This feature lets you select English, Spanish, or Portuguese as the language for your on-screen menus.

A . Press MENU•PROG on remote to see VCR MAIN MENU on the

TV screen.

B . Press 5 to display the LANGUAGE menu.

¥ Press 1 to display the menus in English.

¥ Press 2 to to display the menus in Spanish.

¥ Press 3 to to display the menus in Portuguese.

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

4 Preferences

5 Language

LANGUAGE

Select a language.

1 English

2 Spanish

3 Portuguese

Press MENU to continue

8


Startup

9.

Place channels in the VCR’s memory.

Channels 2 through 13 including line inputs (L1 and L2) are in the

VCRÕs memory when you first turn it on. The VCR stops on these channels when you press CHAN up or down on the remote or

CHANNEL up or down on the VCR. To get additional channels available on your antenna or cable system, you must use the Auto

Channel Search feature of the VCR. If you ever change cable or antenna signals, you may need to auto channel search again. See Cable

Box Setup on page 23.

A . Press VCR1 to set remote to control VCR.


If the menu does not appear on the TV screen:

¥ Press VCR1 and then press MENU•PROG.

¥ If you have used one of the basic hookups, make sure the TV is tuned to the same channel (3 or 4) as the Output Channel selected in the PREFERENCES menu.

Check VCR indicator in display panel Ñ it should be on. Press

TV•VCR to turn it on.

¥ If you have connected your VCR using one of the advanced hookups, tune your TV to its video input (refer to TV OwnerÕs manual).

¥ Check the connections.

C . Press 3 to select CHANNELS.

D . Press 1 to begin Auto Channel Search.

Wait until the channel numbers stop changing. The TV will then tune to the lowest channel found. Press CHAN up or down on the remote or CHANNEL up or down on the VCR to select the active channels.

The VCR automatically selects ANTENNA or CABLE for the Signal

Type feature in the CHANNELS menu. If you need to change the setting manually, press 3.

10.

Add or remove channels from the VCR’s memory.

You may want to add or remove channels if some of the channels are not active, have weak signals, or you do not want to watch them.



C . Press 3 to display the CHANNELS menu.

D . Press 2 to display the ADD/REMOVE CHANNELS menu.

E . Follow the directions on the screen.

F.

Add or remove more channels by entering channel numbers or using the CHAN up or down on the remote or CHANNEL up or down on the VCR.

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

CHANNELS

1 Auto Channel Search

2 Add/Remove Channels

3 Signal Type: CABLE

4 Cable Box Setup

0 Exit

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

CHANNELS



ADD/REMOVE CHANNELS

CH 03 is presently ADDED

Press CLEAR to remove

Press MENU to exit continued on next page

9


Startup

11. Use TV•VCR button.

Skip this step if you used one of the advanced hookups.

When using one of the basic hookups, the TV•VCR button lets you switch between the picture coming from the VCR or the picture from the TV channel. This button lets you record a program on the VCR while watching another channel on the TV. Details are on page 21.

The VCR will automatically switch the TV¥VCR setting to

VCR every time the VCR is turned on, a tape with the safety tab removed is inserted, or you press PLAY.

A . Press VCR1 to set the remote to control the VCR.

B . Press TV•VCR to see the picture from the VCR.

The VCR indicator lights in the display panel.

C . Press CHAN up or down on the remote or CHANNEL up or down on the VCR to change channels on the VCR.

The channel number changes in the display panel.

D . Press TV•VCR to see the TV channels.

The VCR indicator does not light in the display panel.

Change channels using the TVÕs remote.

E . Return the TV to the VCR viewing channel (3 or 4) Ñ the same Output Channel you selected in step 6.

F . Press VCR1, then TV•VCR to switch back to the picture from the VCR.

12. Set the time and date.

When you first turn on the VCR, Ð Ð : Ð Ð appears in the clock area of the VCRÕs display panel.

A . Press MENU•PROG on remote to see VCR MAIN MENU on the TV screen.

B . Press 2 to display SET CLOCK.

C . Enter the time and date with the number buttons on the remote.

¥ Press 0 before single-digit numbers.

Example: press 0, then 5, then 0, then 7 for a time of 5:07. Press 1 for AM or 2 for PM.

¥ Press CLEAR on the remote to change incorrect entries.

D . Press MENU•PROG to remove the SET CLOCK menu from the TV screen and start the clock.

E . Press 0 to exit the menu system.

The time and date appear on the TV screen whenever you press DISPLAY, and the time appears in the display panel.

VCR SLP

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

SET CLOCK

Time --:--

(hh:mm)

Date --/--/--

Press MENU to exit

10

Using the Remote Control

Controlling a VCR

The VCRÕs remote controls two compatible GE, RCA, or ProScan VCRs with the VCR1 and VCR2•LD buttons. Most compatible VCRs automatically respond to VCR1 without being programmed. If you own two compatible

VCRs, test them to see if VCR1 turns on both VCRs. If it does, then you may want to program this VCR to respond to the VCR2•LD button on the remote.

Program the VCR for Remote Control

Set the Remote Control feature of the VCR to the

VCR1 or VCR2•LD position. The remote then controls the VCR with either the VCR1 or

VCR2•LD button Ñ whichever position you select in the menu.

1 . Press MENU•PROG to display the VCR

MAIN MENU .

2 . Press 4 to display PREFERENCES.

3 . Press 1 to activate the Remote Control feature.

4 . Press VCR1 or VCR2•LD to change the setting and program this VCR to respond to the VCR1 or VCR2•LD button Ñ whichever you select.

Important Reminder: Remember you must press VCR1 or VCR2•LD on the remote Ñ whichever you selected in the menu Ñ before the remote will operate this VCR.

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

4 Preferences

PREFERENCES


2 Front Panel: AUTO

3 Output Channel: 3



0 Exit

PREFERENCES


2 Front Panel: AUTO

3 Output Channel: 3



Press VCR2 to change

11


Buttons

POW

ER

VCR1

VCR2•LD

TV

REW PLAY FF

REC

DISPLAY

STOP

CHAN

PAUSE

SEARCH

MUTE

1

4

7

INPUT 0

5

8

2

CHAN

3

PREV CH

6

9

TV•VCR

CLEAR

F.ADV

SLOW

+

MENU

*

PROG

SPEED

EDIT

3

TRACKING

4

Component Buttons

Press one of the buttons to set the remote to operate that component.

TV

Turns on a compatible GE, RCA, or ProScan TV and sets the remote to control the TV.

Used with POWER button to turn on another brand of TV, other than GE, when the remote is programmed to control that

TV. (See page 14.)

VCR1

Turns on a compatible GE, RCA, or ProScan VCR and sets remote to control the VCR.

VCR2•LD

Turns on a compatible GE, RCA, or ProScan VCR and sets remote to control VCR when it has been setup. (See page 11.)

Used with POWER button to turn on compatible RCA or

ProScan LaserDisc player.

VCR Function Buttons

Press VCR1 (VCR2•LD) to set remote to control the VCR to use the function buttons.

CHAN Up or Down

Selects next higher or lower channel in the VCRÕs channel memory.

CLEAR

Resets time counter to 0:00:00.

Allows you to change entries when setting the clock or VCR for a timer recording.

DISPLAY

Shows VCR operating displays on the TV screen.

Displays the time counter.

EDIT

Signals two properly connected

VCRs to begin copying a tape.

See page 25.

F.ADV (Frame Advance)

Lets you view one frame with each press of the button when tape is in stop-action pause.

FF (Fast Forward)

Fast forwards the tape when the

VCR is stopped.

Searches the picture in forward motion during playback.

INPUT

Turns the line input on or off.

L1 or L2 appears in VCRÕs display panel and VIDEO1 or

VIDEO2 appears on TV screen.

Line input refers to the signal coming from the component connected to the audio/video input jacks on the back (L1) or front (L2) of the VCR.

MENU•PROG

Displays the VCR MAIN MENU on the TV screen.

Removes a menu from the screen.

Numbers (0 through 9)

Select a channel up to 99 by pressing two numbers.

Select a cable channel over 99 by pressing and holding 1 until 1– – appears on the screen. Then press the other two numbers.

PAUSE

Pauses action for viewing during playback.

Pauses recording to prevent recording of unwanted scenes.

12


Buttons

VCR Function Buttons

(continued)

PLAY

Plays a tape.

POWER

Turns off VCR when remote is set to control the VCR.

PREV CH (Previous Channel)

Switches between two channels.

Select one channel and then use the number buttons to select the other channel. Press PREV CH to switch between the two channels.

REC (Record)

Starts VCR recording.

Used for one touch recording

(OTR). See page 24.

REW (Rewind)

Rewinds the tape when the VCR is stopped.

Searches the picture in reverse motion during playback.

SEARCH

Displays INDEX and ZERO

SEARCH menus on the TV screen.

Advances tape 60 or 120 seconds during playback.

SLOW – / +

Used for slow-motion forward playback.

SPEED (Tape Speed)

Selects a recording speed

(SP, LP, SLP).

STOP

Stops the normal functions such as record, playback, rewind, fast forward, and pause of the VCR.

TRACKING Up or Down

Lets you manually reduce the streaks that may appear on the picture during play or pause.

Reduces picture ÒjitterÓ during stop-action playback.

TV•VCR

Switches the picture signal so that it either comes from the VCR or the TV channel. See page 10.

TV Function Buttons

Press the TV button to set remote to control a compatible TV. Some buttons may not work with the TV.

CHANNEL Up or Down

Selects next higher or lower channel in the TVÕs channel memory when remote is set to control a TV.

CLEAR

Removes menus or status displays from the screen.

DISPLAY

Shows the status displays on the screen.

Removes menus or displays from the screen.

MUTE

Turns the TV sound on or off.

Numbers (0 through 9)

Select a channel up to 99 by pressing two numbers.

Select a cable channel over 99 by pressing and holding 1 until 1– – appears on the screen. Then press the other two numbers.

POWER

Turns off a compatible TV when remote is set to control TV.

Used with TV button to turn on a compatible TV, other than GE, when the remote is programmed to control that TV. See page 14.

PREV CH (Previous Channel)

Switches between two channels.

Select one channel and then use the number buttons to select the other channel. Press PREV CH to switch between the two channels.

SLOW + and Ð

Used with the TVÕs menus to select and adjust features.

VOL (Volume) Up or Down

Raises and lowers sound of TV.

13


Controlling a TV

The VCRÔs remote is preprogrammed to control the basic functions of a compatible

GE, RCA, or ProScan TV. The remote can also be set up to control other manufacturerÔs brands. To program the remote, enter remote code numbers that correspond to your brand.

Program the Remote for a TV

1 . Turn on the TV.

2 . Point the VCR remote at the TV.

3 . Hold the TV button and press two number buttons to enter the code for your brand. If the

TV changes channels when you press CHAN up or down, setup is complete.

4 . Release the buttons.

5 . Repeat steps 2 – 4 with a different code if the first one does not work.

Helpful Hint: Notice the difference between the TV and VCR on-screen displays. This is one way to tell if the remote is set to control the VCR or the TV.

Brand *

Remote

Button Brand *

Hitachi

Infinity

J C Penney

JBL

Jensen

JVC

Kawasho

Kenwood

Loewe

Luxman

LXI

Magnavox

Marants

Marantz

MGA

Mitsubishi

MTC

Akai

AOC

Candle

Citizen

Colortyme

Concerto

Curtis Mathes

Daewoo

Daytron

Electrohome

Emerson

Envision

Fisher

GE

Goldstar

Hallmark

06

04

00,01,06,09

04

06

10,11

03,06

06

04

06

04,05,07

04,06

04

04,06,12

06

06,12

06

03

06

06

06

06

06

01,06

06

06

06

06

05,06

05,08

00,01,06,11

06

06

NAD

NEC

Panasonic

Philco

Philips

Pioneer

Portland

ProScan

Proton

Quasar

Radio Shack

RCA

Realistic

Sampo

Samsung

Sanyo

Sears

Sharp

Sony

Soundesign

Sylvania

Technics

Techwood

Teknika

TMK

Toshiba

Universal

Victor

Wards

Zenith

* The remote may not be able to control every model TV of the brands listed.

Remote

Button

01,05,06,07,

08,10,

06,13

03

06

04,06

11

06

06

06

05,07,09

00

10

00,01,04,06,

13

02

07

06

04,11

04,06

03,04,06

06

06

01

06

11

01,05,13

01,06

05

06

06,09

05,08

Operate the TV

After you have set up your remote to control your TV, test the TV buttons to see which ones operate your TV.

1 . Point the remote at the TV and press TV.

2 . If TV does not turn on in step 1, press TV and then POWER.

3 . Use the ÒTV Function ButtonsÓ as described on page 13.

14

Playing a Tape

Operating Instructions

NTSC Video Playback Mode

You can select the type of playback for tapes recorded in NTSC.

1 . Press MENU•PROG on the remote to see the VCR MAIN MENU on the TV screen.

2 . Press 4 to display the PREFERENCES menu.

3 . Press 5 to select NTSC or PAL playback.

¥ Select Play NTSC as: PAL to have the tape play back in

PAL.

¥ Select Play NTSC as: NTSC to have the tape play back in

NTSC.

Play a Tape

1 . Turn on the TV and tune it to channel 3, 4, or TVÕs video input to see the picture from the VCR.

2 . Insert a tape in the VCR.

VCR automatically turns on. The cassette-in indicator lights and the VCR indicator lights. The tape automatically begins playback if the safety tab on the cassette has been removed.

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

4 Preferences

PREFERENCES


2 Front Panel: AUTO

3 Output Channel: 3



0 Exit

Safety Tab

3 . Press PLAY, if necessary. PLAY appears in the VCRÕs display panel.

4 . Press TRACKING up or down to remove any streaks from the picture, if necessary. Details are on page 17.

5 . Press STOP.

6 . Press REW.

The VCR will automatically rewind the tape if it reaches the end of the tape during playback. While rewinding, you can press POWER and the VCR will turn off after rewinding.

7 . Press EJECT on the VCR to eject the tape once it is completely rewound.

15


Using the Playback Features

Auto Head Cleaner

The VCR has an automatic head cleaner that minimizes the need for professional head cleaning.

Pause for Stop Action

This feature stops the tape in action and allows you to examine the details of the scene. Stop action works best for tapes recorded in the SP and SLP speed.

1 . Press PAUSE during playback to stop the action.

STILL appears in the VCRÕs display panel.

2 . Press TRACKING up or down to reduce any jittering of the picture.

3 . Press PAUSE or PLAY to return to playback.

The VCR will automatically switch from stopaction playback to stop after a few minutes.

Frame Advance

Frame advance lets you view one stop-action frame after another in forward sequence. Frame advance works best for tapes recorded in the SP or SLP speed.

1 . Press PAUSE during playback to stop the action.

2 . Press F.ADV each time you want to view a frame of the scene.

3 . Press PAUSE or PLAY to resume normal playback.

POWER VCR1

VCR2•LD

REW

PLAY

REC

DISPLAY

STOP

CHAN

FF

PAUSE

SEARCH

TV

VOL

VOL

MUTE

1

2

CHAN

3

PREV CH

4

5

6

7

8

9

INPUT

0

CLEAR

MENU

* PROG

F.ADV

SLOW

+

TV•VCR

SPEED

EDIT

3

TRACKING 4

16

CRK70VD



Slow Motion

You can view the picture in forward slow motion during play or play pause.

SLOW up and down allow you to change the speed. Sound is turned off during slow-motion playback. Slow motion works best in the SP or SLP speed.

1 . During playback, press SLOW – or + to start slowmotion playback.

SLOW+ appears in the VCRÕs display panel.

2 . Press SLOW + to increase the speed or – to decrease the speed.

3 . Use TRACKING up or down to remove any streaks from the picture.

4 . Press PLAY to return to playback.

The VCR will automatically switch from slowmotion playback to stop after a few minutes.

Picture Search

You can search a picture during playback by fast forwarding or rewinding the tape.

Sound is turned off during picture search. The picture is best for tapes recorded in the SP or SLP speed.

Fast Forward Search

1 . Press FF on the remote or FWD on the VCR to search forward at a faster-than-normal speed.

2 . Press FF on the remote, FWD on the VCR, or PLAY to return to playback.

Rewind Search

1 . Press REW to search in reverse at a faster-thannormal speed.

2 . Press REW or PLAY to return to playback.

Digital Auto Tracking

The VCR has digital auto tracking which adjusts the picture when playing back a tape recorded on another VCR. Automatic tracking is turned on whenever a tape is inserted or the VCRÕs power is turned on.

Manual Tracking

Occasionally, you may need to manually adjust tracking on a tape recorded on a different VCR or camcorder. The TRACKING buttons on the remote or VCR are used when playing a tape. They have no effect during recording.

¥ When streaks or snow appear, press TRACKING up or down for the best possible picture.

¥ Press TRACKING up or down during stop-action pause to reduce picture ÒjitterÓ.

POWER VCR1

VCR2•LD

REW

PLAY

FF

REC

DISPLAY

STOP

CHAN

PAUSE

SEARCH

TV

VOL

VOL

MUTE

1

2

CHAN

3

PREV CH

4

5

6

7

8

9

INPUT

0

CLEAR

MENU

* PROG

F.ADV

SLOW

+

TV•VCR

SPEED

EDIT

3

TRACKING

4

C

17



DISPLAY Button

1.

Press DISPLAY on the remote to display the status of the VCR, channel number, time counter, date, time, and tape speed on the TV screen. The time will appear in the display panel.

The time and date must be set before they are displayed. If you do not press DISPLAY again, these displays will time out.

2.

Press DISPLAY again to have only the time counter remain on the TV screen. The time counter will appear instead of the time in the

VCRÕs display panel.

3.

Press DISPLAY again to remove the time counter from the TV screen.

The time counter will remain in the VCRÕs display panel and no status displays will appear on the TV screen. This is convenient for editing tapes.

4.

Press DISPLAY again to return to the normal status displays.

Turning off the VCR automatically returns the displays to normal.

Press

DISPLAY

Press

DISPLAY

Again

Press

DISPLAY

Again

STOP CH 05 0:30:00

Status Displays

Will Time Out

11/18/95 Sat 01:30AM SLP

Hours

0:30:00

Minutes

Seconds

Time Counter Only

Will Not Time Out

No Displays

Time Counter

The time counter shows the actual time it takes to record a program or play back a segment of a prerecorded tape. It helps locate the beginning or end of programs you taped. The time counter resets to 0:00:00 whenever the tape is ejected from the VCR.

For example, if a 30-minute program was recorded at the beginning of the tape, you would:

1.

Insert the prerecorded tape. Press STOP.

Make sure the tape is rewound.

2.

Press DISPLAY on the remote twice to display only the time counter on the TV screen.

3.

Press CLEAR on the remote to reset the time counter to 0:00:00.

4.

Press FF on the remote or FWD on the VCR to fast forward the tape until the time counter reads 0:30:00. Press STOP.

This is the approximate end of the program and you can begin recording at this spot.

5.

Press DISPLAY twice to remove the time counter from the screen and return to the normal displays.

POWER VCR1

VCR2•LD

REC

DISPLAY

REW

PLAY

FF

STOP

CHAN

PAUSE

SEARCH

TV

VOL VOL

MUTE

1

2

CHAN

3

PREV CH

4

5

6

7

8

9

INPUT

0

CLEAR

MENU

* PROG

F.ADV

– SLOW

+

TV•VCR

SPEED

EDIT

3

TRACKING

4

18



Index Search

The VCR has a ÒVHS Index Search SystemÓ that automatically records an index mark on the tape every time you stop and then start a new recording. During playback you can locate the program you want to play by the number of index marks.

The VCR will automatically locate the index number you select. The VCR will search forward or reverse from the location you are on the tape.

1.

Insert the prerecorded tape and press STOP.

2.

Press SEARCH on the remote to display the INDEX SEARCH menu on the TV screen.

3.

Press two number buttons to enter the number of index marks you want the VCR to search. Press CLEAR on the remote to correct an entry.

4.

Press FF on the remote or FWD on the VCR to search forward.

Press REW to search in reverse.

5.

Press STOP to stop index searching. Some index marks may be missed by the VCR.

¥ A mark too close to your location on the tape.

¥ The mark at the beginning of a recorded segment of five minutes or less.

¥ The first index mark on the tape when you start at the beginning of the tape.

INDEX SEARCH

Enter Index Number

01

Press FWD or REW

Press SEARCH to exit

0:30:00

Zero Search

The zero search feature allows you to quickly return to a counter reading of 0:00:00 at any spot on the tape. This is convenient when you want to watch a segment of the tape several times.

1.

Insert the prerecorded tape and press STOP.

2.

Press DISPLAY twice to display only the time counter on the TV screen.

3.

Locate the point on the tape that you want to return to quickly.

4.

Press CLEAR to reset the time counter to 0:00:00.

5.

You can continue to play the tape or perform other functions.

When you are finished, press STOP.

6.

Press SEARCH twice to display the ZERO SEARCH menu. The current tape counter is displayed.

POWER

VCR1

REW

VCR2•LD

PLAY

REC

STOP

DISPLAY

ZERO SEARCH

Current tape counter is

2:17:25

ZERO SEARCH

Current tape counter is

-2:17:25

CHAN

VOL

PAUSE

SEARCH

VOL

FF

TV

Press REW to go to 0:00


Press FWD to go to 0:00


7.

Press REW to return to 0:00:00. The time counter is displayed in the upper right corner of the TV screen during search.

If the time counter reading has a minus (Ð ) in front of it, press FF on the remote or FWD on the VCR to return to a reading of 0:00:00.

MUTE

1

2

CHAN

3

PREV CH

4

5

6

7

8

9

INPUT

0

CLEAR

MENU

* PROG

F.ADV

–

SLOW

+

TV•VCR

SPEED

EDIT

3

TRACKING 4

Commercial Scan

This is useful for scanning commercials or short program segments.

1 . Press SEARCH once during playback to advance the tape approximately 60 seconds.

2 . Press SEARCH twice during playback to advance the tape approximately 120 seconds.

19

Recording a Program

Types of Recordings

Your VCR provides different types of recording. These types are explained in the following sections:

Basic Recording Ð Operating Instructions

Recording While You're Away

Timer Recording

One Touch Recording (OTR)

Using Two VCRs for Copying Tapes

Using the Recording Features

Recording Speeds

Press SPEED on the remote to select a recording speed (SP, LP, or SLP). The speed you select appears on the TV screen and in the VCRÕs display panel. The VCR automatically selects the playback speed (SP, LP, or SLP).

Cassette

Type

T120

T160

Recording Time

SP LP SLP

2Hr 4Hr 6Hr

2Hr 40Min 5Hr 20Min 8Hr

SP (Standard Play) gives the best quality recording. That is why most prerecorded, rental tapes are recorded in SP. Fewer programs can be recorded on the tape. Special effects such as pause, slow motion, picture search, and frame advance work well in SP.

LP (Long Play) gives twice the recording time of tapes recorded in SP. Special effects in playback are not recommended in LP.

SLP (Super Long Play) gives three times the recording time of tapes recorded in SP. Special effects such as pause, slow motion, picture search, and frame advance work well in SP.

Recording Pause

This feature allows you to prevent recording short passages of unwanted material.

Press PAUSE during recording to stop and start recording.

REC P appears in the VCRÕs display panel.

The VCR will automatically switch from pause to stop after a few minutes.

20


Basic Recording – Operating Instructions

To Make a Recording

Turn on the TV and tune it to the VCR viewing channel, either 3, 4, or TVÕs video input channel.

1.

Insert a tape with safety tab in place.

The cassette-in indicator lights in the VCRÕs display panel.

2.

Press VCR1 (VCR2•LD) to set remote to control the VCR.

3.

If using one of the basic hookups, make sure the VCR indicator appears in the VCRÕs display panel. If not, press TV•VCR to turn it on.

4.

Select recording speed using SPEED on the remote.

The tape speed indicator appears in the VCRÕs display panel and on the TV screen.

5.

Select the channel to be recorded.

The channel number appears in the VCRÕs display panel and on the

TV screen.

6.

Press REC on the remote or RECORD on the VCR to begin recording. REC appears in the VCRÕs display panel while the VCR is recording.

Watch a TV Channel While VCR is Recording a Different

Channel

1.

Follow steps 1 through 6 above.

2.

If using one of the basic hookups, press TV•VCR to switch to the

TV channel. The VCR indicator will turn off in the display panel.

3.

Press TV to set the remote to control TV functions for a compatible

TV.

4.

Select the channel you want to watch with the TVÕs channel buttons.

5.

Press STOP when recording is finished.

21


Recording While You’re Away (Timer Recording)

The timer program feature lets you program the VCR to record up to eight different programs within a one year period. Before setting the timer, make sure that:

¥ The clock is set correctly.

¥ A tape with safety tab has been inserted with enough tape to record the programs.

¥ The remote is set to control the VCR Ñ using VCR1 (VCR2•LD).

¥ If you receive all channels through a cable box (or satellite receiver), select a cable box or satellite receiver channel on the next page.

Setting a Timer Recording

VCR MAIN MENU

1 Timer Recordings

1.

Press MENU•PROG on remote to display VCR MAIN

MENU .

2.

Press 1 to display TIMER RECORDINGS menu.

3.

Press 1 to display Create a New Program menu.

4.

Press 1, 2, 3, or 4 to select type of program.

1 One Time Ñ single program recorded once.

2 Daily Ñ program recorded at same time every day.

3 Weekdays Ñ program recorded at same time Monday through Friday.

4 Weekly Ñ program recorded at same time once a week.

5.

Press number buttons on the remote to enter the channel number (or INPUT on the remote to select the line input), start time including AM or PM, end time, and start date of the recording. Just follow the on-screen prompts.

Press CLEAR to correct an entry.

If you receive all channels from a cable box (or satellite receiver) and have completed CABLE BOX SETUP, the output channel of your cable box (or satellite receiver) will automatically appear on the display.

6.

Select recording speed using SPEED on the remote.

7.

Press MENU•PROG to enter your program. A reminder appears which will time out or you can press

MENU•PROG to return to the VCR MAIN MENU.

PROGRAMS OVERLAP may appear on the screen if you have entered two programs where the times overlap.

8.

The TIMER RECORDINGS menu appears. Press 1 to enter an additional timer program, or press 0 to exit.

9.

Turn off the VCR

before recording begins.

TIMER appears in the VCRÕs display panel when the timer has been programmed.

10.

If using a cable box, leave it turned on and tuned to the channel you want to record.

TIMER RECORDINGS

1 Create a New Program

How often should this program record?

1 One Time

Program 1 (One Time)

Channel --


Channel 08

Start Time --:--


Channel 08

Start Time 02:10 AM 1=AM

End Time --:-- 2=PM


Channel 08

Start Time 02:10 PM

End Time 03:35 PM

Start Date 11/18/95 Sat

Tape Speed SLP

Press CLEAR to correct

Press MENU to save

Program 1 has been saved.

Stopping a Recording in Progress

With the VCR: Press POWER and then STOP within a few seconds.

With the Remote: Press VCR1 (VCR2•LD) and then STOP within a few seconds.

22


Recording While You’re Away (Timer Recording)

Select Cable Box (or Satellite Receiver) Channel

If you receive all channels from a cable box (or satellite receiver) and complete Cable Box

Setup , the VCR will automatically enter the output channel of your cable box (or satellite receiver) as the channel to be recorded in the TIMER RECORDINGS menu.

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

1.

Press MENU•PROG to display the VCR MAIN MENU on the TV screen.

2.

Press 3 to select CHANNELS menu.

3.

Press 4 to select CABLE BOX SETUP menu.

4.

Cable box not used for all channels: Press 2. You are finished with cable box setup.

Cable box used for all channels: Press 1 to continue .

5.

Press two numbers on the remote to enter the output channel of your cable box (or satellite receiver). Press 0 before a single-digit number. Valid numbers are 01 – 99.

If you connected your cable box (or satellite receiver) to the VCR using itÕs AUDIO/VIDEO OUT jacks, press INPUT on the remote to select the VIDEO IN option.

Press CLEAR on the remote to correct an entry.

6.

Press MENU•PROG to proceed.

A message appears showing the output channel of your cable box (or satellite receiver) that the VCR will automatically enter as the channel to be recorded in the

TIMER RECORDINGS menu.

7.

Press MENU•PROG to proceed.

CHANNELS



3 Signal Type: CABLE

4 Cable Box Setup

CABLE BOX SETUP

Is a cable box being used ith the VCR for all channels?

1 Yes

2 No

CABLE BOX SETUP

Enter the output channel of the cable box.

--

CABLE BOX SETUP

The VCR will now receive all channels from the cable box on VCR Ch 03.

Press MENU to exit

Check or Clear a Timer Recording

1.

Press MENU•PROG on remote to display the VCR MAIN

MENU on the TV screen.

2.

Press 1 to display the TIMER RECORDINGS menu.

3.

Press 2 for Review Existing Progs. feature.

The first program in the timer is displayed.

¥ Check the Programs: Press MENU•PROG to display information for the next program.

¥ Clear the Program: Press CLEAR when the program appears that you want to delete.

Timer Recording From the VCR’s Line Input

The line input refers to the signal coming from the

AUDIO and VIDEO IN jacks of the VCR. Recording from the line input is convenient if you have a satellite receiver or similar component attached to these jacks.

To timer record from the component connected to the

VCRÕs line input:

Press INPUT to enter the channel number when you program the timer. Enter VIDEO1 to record from the jacks on back of the VCR or VIDEO2 to record from the jacks on the front of the VCR.

VCR MAIN MENU

1 Timer Recordings

TIMER RECORDINGS

1 Create a New Program

2 Review Existing Progs.


Channel 08

Start Time 02:10 PM

End Time 03:35 PM

Start Date 11/18/95 Sat

Tape Speed SLP

Press CLEAR to delete

Press MENU for next prog


Channel VIDEO1

Start Time --:--

End Time --:--

Start Date --/--/--

Tape Speed SLP

Press CLEAR to correct

Press MENU to exit

23


One Touch Recording

One touch recording lets you record up to four hours without using the timer program feature. The VCR will turn off automatically at the end of the recording.

RECORD

VCR SLP

H M

Display showing 30 minutes remaining for one touch recording.


1.

Turn on the VCR.

2.

Insert a tape with safety tab in place.

3.

Select the channel you want to record.

4.

Select the desired recording speed using SPEED on the remote.

5.

Press REC on the remote or RECORD on the VCR to activate recording.

6.

Press REC on the remote or RECORD on the VCR repeatedly until the amount of recording time for the program is displayed in the VCRÕs display panel or on the TV screen.

RECORD LENGTH 0:00

CH 04

Press REC to set length

One Touch Display on

TV Screen

Press Recording

RECORD Time

0:30

1:00

( 30 Min)

(1 Hr)

1:30

2:00

3:00

4:00

0:00

(1 Hr, 30 Min)

(2 Hrs)

(3 Hrs)

(4 Hrs)

(OTR Turns Off)

Each press increases the time Ñ 30 minutes up to four hours.

The amount of time the VCR will record and X– REC will appear in the VCRÕs display panel.

You can increase the amount of recording time by pressing REC on the remote or RECORD on the VCR.

Stopping a Recording in Progress

With the VCR: Press POWER and then STOP within a few seconds.

With the Remote: Press VCR1 (VCR2•LD) and then STOP within a few seconds.

POWER VCR1

VCR2•LD

REW

PLAY

REC

DISPLAY

STOP

CHAN

FF

PAUSE

SEARCH

TV

VOL VOL

MUTE

1

2

CHAN

3

PREV CH

4

5

6

7

8

9

INPUT

0

CLEAR

MENU

* PROG

F.ADV

– SLOW

+

TV•VCR

SPEED

EDIT

3

TRACKING 4

24

C


Using Two VCRs for Copying and Editing Tapes


(Refer to hookup on page 6.)

Use this VCR as the playback VCR and the other VCR as the recording VCR. If you have two compatible VCRs, use the AutoEdit feature described below.

1.

Turn on the TV and VCRs.

2.

Tune TV to the VCR viewing channel, either 3, 4, or TVÕs video input.

Caution: The unauthorized recording of television programs and other materials may infringe the rights of others.

3.

If you have connected your VCR using Option A (page 6), tune recording VCR to channel 3 or 4 Ñ the one selected in the Output

Channel feature in the PREFERENCES menu.

If you have connected your VCR using Option B (page 6), press INPUT on recording VCR to select the line input. Select L1 to record from jacks on the back of the VCR or L2 to record from jacks on the front of the

VCR.

4.

Insert the tape you want to copy into playback VCR. Insert a blank tape with safety tab in place into recording VCR.

To prevent recording on-screen displays from the playback VCR, press

DISPLAY three times. See page 18 for details.

5.

Press PLAY, then PAUSE on playback VCR when you reach the point on the tape or program where you want to begin copying. If the tape was not recorded on the playback VCR, streaks may appear and you may need to adjust tracking.

6.

Press RECORD, then PAUSE, on the recording VCR.

7.

Press PAUSE buttons on both VCRs at the same time to begin copying the tape.*

8.

Edit out segments that you do not want to copy by pressing PAUSE on recording VCR to stop copying the tape. Then locate the next segment you want to copy on the playback VCR by using FWD, REW, and PLAY .

Press PAUSE on the playback VCR. Press PAUSE at the same time on both VCRs to resume copying.

9.

Press STOP on both VCRs when you are finished.

* You may turn off the TV after the recording has started as it does not have to be on to copy a tape.

Using Dual Remote with AutoEdit

TM

Use this VCR as the playback VCR and set it to respond to VCR2•LD on the remote as described on page 11.

Use your other compatible VCR as the recording VCR, which should respond to VCR1 .

1.

Follow steps 1 – 4 in the ÒOperating InstructionsÓ above.

2.

Press VCR1 on remote to control recording VCR. Press REC on the remote, then PAUSE, to put recording VCR in pause mode.

3.

Press VCR2•LD on remote to control playback VCR.

4.

Use FF, REW, and PLAY to locate the point where you want to begin copying. Press PAUSE while VCR is playing to put playback VCR in pause mode.

5.

Press EDIT on remote to start the VCRs copying.

6.

Press EDIT again when you want to stop the tape from copying.

7.

Repeat steps 4 – 6 as needed.

8.

Press VCR1, STOP, then VCR2•LD, STOP, when you are finished.

25

References

Location of Controls

Front Panel

Tape Compartment

Remote Sensor

CHANNEL/ TRACKING ( Up or Down)

Selects next higher or lower channel in the VCRÕs channel memory.

Adjusts tracking when a tape is playing.

EJECT

Press when the VCR is stopped to eject the cassette.

FWD (Fast Forward)

Fast forwards the tape when the VCR is stopped.

Searches the picture forward during playback.

INPUT

Turns the line input on or off. L1 or L2 appears in VCRÕs display panel and

VIDEO1 or VIDEO2 appears on the TV screen.

Line input refers to the signal coming from the component connected to the audio/video input jacks on the back (L1) of the VCR or front (L2) of the VCR.

PAUSE

Pauses action for viewing during playback.

Pauses recording to prevent recording of unwanted scenes.

PLAY

Plays a tape.

POWER

Turns the VCR on or off.

RECORD

Starts VCR recording.

Used for one touch recording.

Remote Sensor

Receives signals from the remote control.

Aim the remote at this sensor with no objects between them.

REW

Rewinds the tape when the VCR is stopped.

Searches the picture in reverse during playback.

STOP

Stops the normal functions such as record, playback, rewind, fast forward, or pause.

TV•VCR

Switches the picture signal so that it either comes from the VCR or the TV channel.

See page 10.

VIDEO and AUDIO IN Jacks

Receives signals from another component, like a VCR or camcorder, when it is connected to these jacks.

Use INPUT to select L2 in the VCRÕs display panel to record from these jacks.

26

References


Back Panel

IN

OUT

AUDIO VIDEO

IN

OUT

IN

ANTENNA

OUT

ANTENNA IN Connector

Receives the signal from an antenna or cable system that is attached to this connector.

ANTENNA OUT Connector

Passes signal to TV using the coaxial cable supplied.

VIDEO and AUDIO IN Jacks

Receives signals from another component, like a VCR or camcorder, when it is connected to these jacks. Use INPUT to select L1 in the

VCRÕs display panel to record from these jacks.

VIDEO and AUDIO OUT Jacks

Sends signals from VCR to another component, like a TV monitor or VCR, when it is connected to these jacks.

Display Panel

This VCR has a feature that allows you to change the brightness level of the fluorescent display panel.

1 . Press MENU•PROG on the remote to see the VCR MAIN

MENU on the TV screen.

2 . Press 4 to display the PREFERENCES menu.

3 . Press 2 to select Front Panel: AUTO, BRIGHT, or DIM.

¥ Select AUTO to keep the display panel bright when VCR is on and dim when it is off.

¥ Select BRIGHT to keep the display panel bright.

¥ Select DIM to keep the display panel dim.

VCR MAIN MENU

1 Timer Recordings

2 Set Clock

3 Channels

4 Preferences

PREFERENCES


2 Front Panel: AUTO

3 Output Channel: 3



0 Exit continued on next page 27

References


Display Panel

Cassette-In

Tape

Speed

VCR SLP

Status Time Counter or Time

Channel Number or Line Indicator

A M

Cassette-In Indicator ( )

Lights when a tape is in the VCR.

Channel Number, L1, or L2

The channel number or line indicator (L1 or

L2) is displayed.

Select L1 to record from the jacks on the back of the VCR or L2 to record from the jacks on the front of the VCR.

Status Indicators

Show what the VCR is doing.

EJECT

FFWD

HELLO

Ejecting Tape

Fast forward

Turned on

PLAY

REC

REC P

REW

SRCH +

SRCH –

SLOW +

Playback

Record

Record pause

Rewind

Forward search

Reverse search

Slow motion

STILL

STILL

STOP

Frame advance

Play pause

VCR stopped

TAPE flashes Set for timer Ð no tape

TIMER

X-REC

Timer recording set

One touch recording in progress

Tape Speed Indicators (SP, LP, or SLP)

Press SPEED on the remote to change.

Time or Time Counter

Press DISPLAY on the remote to switch between the current time and elapsed-time counter.

VCR Indicator (Applies Only to Basic

Hookups)

Press TV•VCR to turn on or off.

VCR indicator on: Picture from VCR.

VCR indicator off: Picture from TV channel.

28

References

Specifications

Format:

Record/Playback

System:

VHS

Video: 4-Head

Audio: 2 Mono record/playback system

Video Signal System: PAL M and NTSC Recording and Playback

Antenna:

Tuner:

75-ohm external VHF/UHF combined antenna terminal

USA: 181 channels capability*

(125 cable channels)

Type:

Power Requirement:

Power Consumption:

AutoProgramming frequency synthesis

100-240-V AC (+/- 10%), 50-60 Hz

18 watts

(6 watts in standby mode)

Dimensions:

Weight:

Other:

3.5 inches high

(90 mm)

15.43 inches wide

(392 mm)

12.1 inches deep

(309.5 mm)

9.46 pounds

(4.3 kg)

Automatic Head Cleaner

30 - Minute Memory Backup

Storage Temperature

Range:

Operating

Temperature Range:

- 22ûF to +149ûF

+41ûF to +104ûF

*Check your cable companyÔs compatibility requirements.

Cleaning the VCR

Use a soft, dry, and clean cloth or dusting attachment of your vacuum cleaner to dust your VCR. Remove dust from the ventilation holes on the top, back, sides, and bottom of the cabinet.

Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Do not use any scouring agents, solvents, or abrasive products.

Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, anti-static cleaner and polisher.

If an object or liquid penetrates the VCR, unplug it immediately and have it checked by an authorized technician.

29

References

Trouble Checks

Sometimes problems can be easily solved by checking a few basic things. Check below before you call for help or take your VCR to an Authorized GE VCR Service Center.

Trouble Here's what to try:

N o power

Clock shows incorrect time or date

Remote locks up

VCR does not respond to remote

Remote no longer controls a GE TV

Remote no longer controls a compatible TV, other than GE

VCR only responds to VCR2•LD button on remote

No picture when VCR turned on Ð using a basic hookup

Poor or no picture for normal TV viewing

Snowy or no picture during playback

No color picture

¥ Plug VCR into an operating outlet.

¥ Check connections.

¥ Power interruption. Clock area in display panel will show - -:- -.

¥ Clock was not set accurately (check AM/PM and date).

¥ Time counter display appears in display panel. Press DISPLAY on remote.

¥ Remove batteries and hold down one or more buttons for several seconds to drain the microprocessor inside the remote to reset it. Reinstall the batteries and try remote again.

¥ Press VCR1 (VCR2•LD) to set remote to control the VCR. See page 11.

¥ Aim remote at VCR with no objects between them.

¥ Change batteries.

¥ Press TV to set remote to control the corresponding compatible TV. See page 14.

¥ Reprogram remote for GE TV. See page 14.

¥ Aim remote at TV with no objects between them.


¥ Press TV to set remote to control a compatible TV. See page 14.

¥ Aim remote at component with no objects between them.

¥ Reprogram remote after batteries have been changed.


¥ Check setting of Remote Control: VCR1/VCR2 feature. See page 11.

¥ Press TV•VCR to turn VCR indicator on. See page 10.

¥ Check TV channel selected (3 or 4) to make sure it matches the channel selected with the Output Channel feature. See page 8.

¥ Press TV•VCR to turn VCR indicator off.

¥ Switch TV to an active channel.

¥ Check antenna connections.

¥ Press TV•VCR to turn VCR indicator on.

¥ Check TV channel selected (3 or 4) to make sure it matches the channel selected with the Output Channel feature. See page 8.

¥ Check TVÕs fine tuning.

¥ Check video cable connections between VCR and TV monitor.

¥ Set TV monitor to video input channel.

¥ Try another tape.

¥ Some snow/streaks are normal during search, frame advance, slow-motion, or stop-action playback.

¥ If tape is recorded in NTSC, make sure Play NTSC as: NTSC or PAL feature is set correctly. See page 15.

¥ If PLAY/NTSC is not set correctly, the VCR may play a black and white picture.

30

References

Trouble

Time counter not working

Will not record or play

Streaks in picture during normal playback

Will not record

Rewind does not operate

Timer recording not made or wrong program recorded

VCR makes noise when stopped

Will not auto search active channels correctly

Cannot select channels over 69

Here's what to try:

¥ The time counter does not advance during unrecorded portions of tape.

When an unrecorded segment of tape is encountered, the time counter will hold its count until recorded material is detected again.

¥ A minus (Ð) will appear in front of the time if you rewind the tape farther back than a counter reading of 0:00:00.

¥ No cassette in VCR.

¥ Eject and re-insert cassette.

¥ Broken tape Ñ try another cassette.

¥ Some snow/streaks are normal during search, frame advance, slow-motion, or stop-action playback.

¥ VCR is in pause mode. Press PAUSE.

¥ Safety tab removed from cassette.

¥ Make sure the line indicators (L1 and L2) are turned off in VCRÕs display panel for normal recording from the VCRÕs tuner. Press INPUT to turn off the line indicator.

¥ Tape already rewound.

¥ Program entered incorrectly (wrong channel or times).

¥ Power interruption. Clock area in display panel will show - -:- -.

¥ Check to see if time and date are correct Ñ including AM/PM.

¥ Program exceeded tapeÕs length or tape was not rewound beforehand.

¥ VCR was not turned off at the time recording was to start.

¥ No tape in VCR or cassetteÕs safety tab broken off.

¥ Cable box not turned on at time recording was to begin.

¥ VCR is removing tape from heads. This is normal. The head cylinder inside the VCR will continue to rotate for a few minutes after you put the VCR in the stop mode.

¥ Check antenna connections.

¥ Check Signal Type: CABLE/ANTENNA feature. See page 9.

¥ Cable channels over 69 can only be selected if Signal Type:

CABLE/ANTENNA feature is set to CABLE. Details are on page 9.

31

References

Index

Accessories, Included . . . . . . . . . . . . . . . . . . . . . . .7

Add or Remove Channels from Memory . . . . . .9

ADD/REMOVE CHANNELS

Menu . . . . . . . . . . . .9

Antenna Connections . . . . . . . . . . . . . . . . . . . . .2,3

ANTENNA IN

Connector . . . . . . . . . . . . . . . .3-6,27

ANTENNA OUT

Connector . . . . . . . . . . . . . .3-6,27

Attaching Power Cord . . . . . . . . . . . . . . . . . . . . . .7

AUDIO

and VIDEO IN Jacks . . . . . . . .6,23,25,26,27

AUDIO

and VIDEO OUT Jacks . . . . . .3-6,23,25,27

Auto Channel Search Feature . . . . . . . . . . . . . . . .9

Auto Head Cleaner . . . . . . . . . . . . . . . . . . . . . . . .16

AutoEdit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Back Panel Controls . . . . . . . . . . . . . . . . . . . . . . .27

Basic Recording . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Batteries, Inserting in Remote . . . . . . . . . . . . . . . .7

Buttons

Components . . . . . . . . . . . . . . . . . . . . . . . .12

TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13

Cable Box Channel, Selecting . . . . . . . . . . . . . . .23

Cable System With Cable Box

Connections . . . . . . . . . . . . . . . . . . . . . .2,4-5

Cable System Without Cable Box

Connections . . . . . . . . . . . . . . . . . . . . . . . .2,3

CABLE BOX SETUP

Menu . . . . . . . . . . . . . . . . .23

Cassette, Inserting . . . . . . . . . . . . . . . . . . . . . . . . .15

Cassette-In Indicator . . . . . . . . . . . . . . . . .15,21,28

CHAN and CHANNEL Up or Down

Buttons . . . . . . . . . . . . . . . . . . . . .10,12-13,26

Channel Number Indicator . . . . . . . . . . . . . . . . .28

CHANNELS

Menu . . . . . . . . . . . . . . . . . . . . . . .9,23

Checking Timer Programs . . . . . . . . . . . . . . . . . .23

Checks, Trouble . . . . . . . . . . . . . . . . . . . . . . . .30-31

Choosing a Hookup . . . . . . . . . . . . . . . . . . . . . . . .2

Cleaning the VCR . . . . . . . . . . . . . . . . . . . . . . . . .29

CLEAR

Button . . . . . . . . . . . . .10,12-13,18,19,22-23

Clearing Timer Programs . . . . . . . . . . . . . . . . . .23

Commercial Scan . . . . . . . . . . . . . . . . . . . . . . . . .19

Connections

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Audio/Video Jacks . . . . . . . . . . . . . . . .2,3-6

Cable TV . . . . . . . . . . . . . . . . . . . . . . . . .2,3-5

Two VCRs . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Controlling

TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Copying and Editing Tapes . . . . . . . . . . . . . . . . .25

Copying Tape, Connections . . . . . . . . . . . . . . . .2,6

Date, Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Design Specifications . . . . . . . . . . . . . . . . . . . . . .29

Digital Auto Tracking . . . . . . . . . . . . . . . . . . . . .17

DISPLAY

Button . . . . . . . . . . . . . . . . . .12-13,18,28

Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . .27-28

Displays, Status . . . . . . . . . . . . . . . . . . . . . . . .18,28

EDIT

Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Editing and Copying Tapes . . . . . . . . . . . . . . . . .25

EJECT

Button . . . . . . . . . . . . . . . . . . . . . . . . . .15,26

Escoge una Lengua . . . . . . . . . . . . . . . . . . . . . . . . .8

F.ADV

(Frame Advance) Button . . . . . . . . . .12,16

Fast Forward Search . . . . . . . . . . . . . . . . . . . . . . .17

FF and FWD (Fast Forward)

Buttons . . . . . . . . . . . . . . . .12,17,18,19,25,26

First-Time Operation . . . . . . . . . . . . . . . . . . . .7-10

Frame Advance . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Front Panel: AUTO/BRIGHT/DIM

Feature . . . . .27

Head Cleaner, Auto . . . . . . . . . . . . . . . . . . . . . . .16

Hookups

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Audio/Video Jacks . . . . . . . . . . . . . . . .2,3-6

Cable TV . . . . . . . . . . . . . . . . . . . . . . . . .2,3-5

Two VCRs . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Index Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

INDEX SEARCH

Menu . . . . . . . . . . . . . . . . . . . . .19

Indicators in Display Panel . . . . . . . . . . . . . . . . .28

Indicators, Status . . . . . . . . . . . . . . . . . . . . . . . . . .28

INPUT

Button . . . . . . . . . . . . . . . . . .12,23,25,26,27

Inserting a Cassette . . . . . . . . . . . . . . . . . . . . . . . .15

L1

and L2 Indicators . . . . . . . . . . . . .12,25,26,27,28

LANGUAGE

Menu . . . . . . . . . . . . . . . . . . . . . . . . .8

Language, Select . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Line Input, Recording From . . . . . . . . . . . . . . . .23

Location of Controls

Remote Control . . . . . . . . . . . . . . . . . . .12-13

VCR Back Panel . . . . . . . . . . . . . . . . . . . . .27

VCR Display Panel . . . . . . . . . . . . . . . .27-28

VCR Front Panel . . . . . . . . . . . . . . . . . . . .26

LP Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Manual Tracking . . . . . . . . . . . . . . . . . . . . . . . . . .17

MENU•PROG

Button . . . . . . . . . . . . . .8,9,12,22-23

MUTE

Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

NTSC Video Playback Mode . . . . . . . . . . . . . . . .15

NTSC Video System . . . . . . . . . . . . . . . . . . . . .8,15

Number Buttons . . . . . . .8-11,12-13,14,15,19,22-23

On-Screen Displays . . . . . . . . . . . . . . . . . . . . . . .18

One Touch Recording . . . . . . . . . . . . . . . . . . . . .24

One Touch recording, Stopping . . . . . . . . . . . . .24

Operation, First Time . . . . . . . . . . . . . . . . . . . .7-10

OTR (One Touch Recording) . . . . . . . . . . . . . . .24

Output Channel, Selecting . . . . . . . . . . . . . . . . . .8

PAL Video System . . . . . . . . . . . . . . . . . . . . . . .8,15

Panel Display Feature . . . . . . . . . . . . . . . . . . . . .27

PAUSE

Button . . . . . . . . . . . . . . . . . .12,16,20,25,26

Pause for Stop Action . . . . . . . . . . . . . . . . . . . . . .16

Pause, Recording . . . . . . . . . . . . . . . . . . . . . . . . .20

Picture Search . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

PLAY

Button . . . . . . . . . . . . . . . . .13,15,16,17,25,26

Playing a Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

POWER

Button . . . . . . . . . . . .11,12-13,14,22,24,26

Power Cord, Attaching . . . . . . . . . . . . . . . . . . . . .7

PREFERENCES

Menu . . . . . . . . . . . . .8,9,11,15,27

32

References

Index

PREV CH

(Previous Channel) Button . . . . . . . .13

Problems, Solving . . . . . . . . . . . . . . . . . . . . . .30-31

Programming Remote to Control

Compatible TV . . . . . . . . . . . . . . . . . . . . . .14

Programming Remote to Control VCR . . . . . . .11

PROGRAMS OVERLAP

Message . . . . . . . . . . . .22

REC

and RECORD Buttons . . . . . . .13,21,24,25,26

REC

Indicator . . . . . . . . . . . . . . . . . . . . . . . . . .21,28

REC P

(Record Pause) Indicator . . . . . . . . . .20,28

Recording

Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

From Another VCR . . . . . . . . . . . . . . . . . .25

One Program While Watching Another .21

One Touch (OTR) . . . . . . . . . . . . . . . . . . . .24

Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .22-23

Recording While YouÕre Away

(Timer Recording) . . . . . . . . . . . . . . . . . . .22

Remote Control . . . . . . . . . . . . . . . . . . . . . . . .11-14

Remote Control: VCR1/VCR2

Feature . . . . . . .11

Remote Function Buttons . . . . . . . . . . . . . . . .12-13

Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Remove or Add Channels from Memory . . . . . .9

REMOVE/ADD CHANNELS

Menu . . . . . . . . . . . .9

REW

(Rewind) Button . . . . . . . . . . .13,15,17,19,25

Safety Precautions . . . . . . . . . .Inside Front Cover

Safety Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Satellite Receiver Channel, Selecting . . . . . . . . .23

SEARCH

Button . . . . . . . . . . . . . . . . . . . . . . . .13,19

Search, Fast Forward . . . . . . . . . . . . . . . . . . . . . .17

Search, Rewind . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Selecione o Idioma . . . . . . . . . . . . . . . . . . . . . . . . .8

Select an Output Channel . . . . . . . . . . . . . . . . . . .8

Select Cable Box or Satellite Receiver

Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Select the Language . . . . . . . . . . . . . . . . . . . . . . . .8

Selecting a Video System . . . . . . . . . . . . . . . . . . . .8

Sensor, Remote . . . . . . . . . . . . . . . . . . . . . . . . . . .26

SET CLOCK

Menu . . . . . . . . . . . . . . . . . . . . . . . .10

Set the Time and Date . . . . . . . . . . . . . . . . . . . . .10

Setting a Timer Recording . . . . . . . . . . . . . . . . . .22

Setting Up the VCR . . . . . . . . . . . . . . . . . . . . . .7-10

Signal Type: CABLE/ANTENNA

Feature . . . . . . .9

SLOW

+ and Ð Buttons . . . . . . . . . . . . . . . . . .13,17

Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

SLOW+

Indicator . . . . . . . . . . . . . . . . . . . . . . .17,28

SLP Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Solving Problems . . . . . . . . . . . . . . . . . . . . . . .30-31

SP Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

SPEED

Button . . . . . . . . . . . . . . . . . .13,20,21,24,28

Speeds, Recording . . . . . . . . . . . . . . . . . . . . . . . .20

Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-10

Status Displays . . . . . . . . . . . . . . . . . . . . . . . . .18,28

STILL

Indicator . . . . . . . . . . . . . . . . . . . . . . . . .16,28

Stop Action Pause . . . . . . . . . . . . . . . . . . . . . . . . .16

STOP

Button . . . . . . .13,15,18,19,21,22,23,24,25,26

Stopping a Timer Recording . . . . . . . . . . . . . . . .22

Stopping an Express Recording . . . . . . . . . . . . .24

Tab, Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . .1

Tape Speed Indicators . . . . . . . . . . . . . . . . . . .20,28

Tape, Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Time and Date, Set . . . . . . . . . . . . . . . . . . . . . . . .10

Time Counter . . . . . . . . . . . . . . . . . . . . . . . .18,19,28

Time Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Time, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

TIMER

Indicator . . . . . . . . . . . . . . . . . . . . . . . .22,28

Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . .22

TIMER RECORDINGS

Menu . . . . . . . . . . . . .22-23

TRACKING

Buttons . . . . . . . . . . . . .13,15,16,17,26

Tracking, Digital Auto and Manual . . . . . . . . . .17

Trouble Checks . . . . . . . . . . . . . . . . . . . . . . . .30-31

Turn On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Turn on VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

TV

Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12,14

TV Control with Remote . . . . . . . . . . . . . . . . . . .14

TV Function Buttons . . . . . . . . . . . . . . . . . . . . . .13

TV, Controlling with Remote . . . . . . . . . .12-13,14

TV, Turn On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

TVs, Compatible Chart . . . . . . . . . . . . . . . . . . . .14

TV•VCR

Button . . . . . . . . . . . . . . . . . . .10,13,21,26

Types of Recordings . . . . . . . . . . . . . . . . . . . . . . .20

VCR Controls . . . . . . . . . . . . . . . . . . . . . . . . . .26-28

VCR Function Buttons . . . . . . . . . . . . . . . . . .12-13

VCR

Indicator . . . . . . . . . . . . . . . . . . . . .10,15,21,28

VCR MAIN MENU

. . . . . . . . . . . .8,9,11,15,22-23,27

VCR, Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

VCR, Controlling with Remote . . . . . . . .11,12-13

VCR, Turn On . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

VCR1 and VCR2•LD

Buttons . . . . . . . .8,9,10,11,12,14,21,22,24,25

VCR1/VCR2

Feature . . . . . . . . . . . . . . . . . . . . . . .11

VCRs Memory, Placing Channels In . . . . . . . . . .9

VCRs, Connecting for Tape Copying . . . . . . . .2,6

Video Playback Mode for NTSC Recordings . .15

Video System, Selecting . . . . . . . . . . . . . . . . . . . . .8

VIDEO1

and VIDEO2 Indicators . . . . . . . . . .23,26

VOL

Up or Down Button . . . . . . . . . . . . . . . . . . .13

Warnings . . . . . . . . . . . . . . . . . .Inside Front Cover

Watch One Channel While

Recording Another . . . . . . . . . . . . . . . . . . 21

X-REC

Display . . . . . . . . . . . . . . . . . . . . . . . . .24,28

Zero Search Feature . . . . . . . . . . . . . . . . . . . . . . .19

ZERO SEARCH

Menu . . . . . . . . . . . . . . . . . . . . .19

33

Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only add delays in service for your product.

10330 North Meridian Street

Indianapolis, IN 46290-1024 USA

©1995 Thomson Consumer Electronics, Inc.

Trademark(s)¨ Registered

Marca(s) Registrada(s)

Printed in Singapore

Part Number 95-VGM300-1

No results