ELECT
Plasma Display
with Media Station
PS42P2SB
PS50P2HB
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
REMOTE CONTROL
ON-SCREEN MENUS
PICTURE IN PICTURE
TELETEXT
ENG
Safety Instructions
ENG
◆ Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall.
◆ Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions.
◆ Do not expose the PDP to direct sunlight and other sources of heat.
◆ Do not expose the PDP to any liquids.
◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the
PDP.
◆ During a storm conditions (especially when there is lightning) unplug the PDP from the mains
socket and aerial.
◆ Do not step on or twist the power cord.
◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the PDP.
◆ If the PDP is broken, do not try to repair it yourself. Contact qualified service personnel.
◆ If the remote control is not used for a long period of time, remove the batteries and store it in a
cool, dry place.
◆ Do not drop the remote control.
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of this screen when displaying a still image.
◆ Cell Defect
The plasma display panel consists of fine cells. Although the panels are produced with more than
99.9 percent active cells, there may be some cells that do not produce light or remain lit.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height and do not install and operate there.
◆ Warranty
- Warranty Period: One year starting from the purchase of your PDP.
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
2
Caution
ENG
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT
REMOVE REAR COVER, NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash and arrow head
within the triangle is a warning sign
alerting you of “dangerous voltage”
inside the product.
☛
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
WARNING: TO PREVENT DAMAGE WHICH MAY
RESULT IN FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
!
The main voltage is indicated on the
rear of the PDP and the frequency is
50 or 60Hz.
Checking Parts
- Owner’s Instruction
- Remote Control / 2 Batteries (AAA)
- Video Cable (DVI)
- 2 Power Cords
- 3 Ferrite Cores
- S-Video Cable
3
ENG
Contents (continued)
◆ FOREWORD
■
■
■
■
Safety Instructions...............................................................................................
User Instructions .................................................................................................
Caution................................................................................................................
Checking Parts....................................................................................................
2
2
3
3
◆ CONNECTING AND PREPARING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
■
Viewing the Plasma Display................................................................................
Viewing the Media Station...................................................................................
Remote Control Buttons......................................................................................
Inserting the Batteries in the Remote Control .....................................................
Installing the Display on the Wall Attachment Panel...........................................
Separating the Display from the Wall Attachment Panel ....................................
Connecting Speakers..........................................................................................
- Connecting PDP and Speakers
- Connecting Stand and Speakers
Connecting to an Aerial (or Cable Television Network) ......................................
Switching On and Off ..........................................................................................
Becoming Familiar with the Remote Control.......................................................
Setting up your Remote Control..........................................................................
Plug and Play ......................................................................................................
Choosing Your Language ...................................................................................
6
7
8
9
9
12
13
14
15
16
17
18
19
◆ USING YOUR DISPLAY (continued)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
4
Storing Channels Automatically ..........................................................................
Sorting the Stored Channels ...............................................................................
Storing Channels Manually .................................................................................
Editing the Channels ...........................................................................................
Fine Tuning Channel Reception..........................................................................
Changing the Picture Standard ...........................................................................
Adjusting the Picture Settings .............................................................................
Changing the Picture Size...................................................................................
Freezing the Current Picture ...............................................................................
Adjusting the Picture Settings (PC or DVI Mode)................................................
Setting the Picture (PC Mode) ............................................................................
Changing the Sound Standard............................................................................
Adjusting the Sound Settings ..............................................................................
Adjusting the Volume Automatically....................................................................
Selecting the Sound Mode ..................................................................................
20
21
22
24
25
26
26
27
27
28
29
30
30
31
32
ENG
Contents
◆ USING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
Setting the Dolby Surround .................................................................................
Adjusting the Dolby Pro Logic Preferences.........................................................
Adjusting the Headphone Preferences ...............................................................
Hearing the Melody Sound..................................................................................
Setting the Current Time .....................................................................................
Switching On and Off Automatically....................................................................
Setting the Sleep Timer.......................................................................................
Viewing the Picture in Picture (PIP) ....................................................................
Listening to the Sound of the Sub Picture...........................................................
Viewing Pictures From External Sources............................................................
33
35
36
37
37
38
39
40
42
43
◆ USING THE TELETEXT FEATURE
■
■
■
■
Teletext Feature ..................................................................................................
Displaying the Teletext Information.....................................................................
Selecting Display Options ...................................................................................
Selecting a Teletext Page ...................................................................................
44
45
46
47
◆ CONNECTIONS AND RECOMMENDATIONS FOR USE
■
■
■
■
■
■
■
■
■
■
■
■
Connecting to the External Devices ....................................................................
Connecting to the DVD Input ..............................................................................
Connecting to the S-Video Input .........................................................................
Connecting to the Audio Output ..........................................................................
Connecting to the DVI Input ................................................................................
Connecting to the PC Input .................................................................................
Preset Signals .....................................................................................................
Setting up Your PC Software (Windows only).....................................................
Input Mode (PC/DVI)...........................................................................................
Pin Configurations...............................................................................................
Care and Maintenance........................................................................................
Troubleshooting: Before Contacting Service Personnel .....................................
Symbols
Press
☛
Important
➢
Note
5
48
49
49
50
50
51
51
52
53
54
55
55
Viewing the Plasma Display
➢
ENG
The actual configuration on your PDP may be different, depending
on your model.
Front Panel
Speaker
Speaker
POWER
Remote Control Signal Receiver
Press to turn the PDP on
and off.
Aim the remote control towards this spot
on the PDP.
SOURCE
External input selection.
MENU
Menu display.
-
+
▼ C/P.
MUTE
Volume adjustment.
▲
Channel selection
Temporary sound switch off.
Rear Panel
DISPLAY SIGNAL IN
POWER IN
Connect the video cable between the PDP
and Media Station.
Plug the mains lead into an appropriate
socket.
➢
6
For further details, refer to “Switching On and Off” on page 15.
Viewing the Media Station
ENG
Front Panel
Channel selection
Headphone connector
S-Video input
Power On/Off
Stand by /Power On indicator
On-Screen display
Audio inputs
Temporary sound switch off
External input selection
Video input
Menu display
Volume adjustment
Rear Panel
➢
For further details about connection, refer to pages 48~51.
e
d
f
g
a
b
m
l
i
c
k
h
j
a) VHF/UHF (75Ω)
75Ω Coaxial connector for Aerial/Cable Network.
f)
b) MONITOR OUT / AV 1 / AV 2 / AV 3
Inputs or outputs for external devices, such as VCR,
DVD, video game device or video disc players.
g) EXTERNAL SPEAKER OUT (8Ω)
Connectors for external speakers.
c) AV4 (S-VIDEO / L-AUDIO-R)
Video and audio inputs for external devices with an
S-Video output, such as a camcorder or VCR.
d) COMPONENT 1 / COMPONENT 2
Video (Y/PB/PR) and audio (L/R) inputs for
Component. (480i/480p, 576i/576p, 720p, 1080i)
➢ For further details, refer to “Preset Signals” on
page 51.
e) SURROUND OUT
Surround amplifier (S-L/S-R) or powered speaker
(CENTER/SUB-WOOFER) connection to take full
advantage of the surround sound effect.
AUDIO OUT (L/R)
Audio outputs for an audio system.
h) PC IN
PC video input.
i)
L-AUDIO-R
PC/DVI audio inputs.
j)
DVI IN
Video input for device with DVI output.
k) DISPLAY SIGNAL OUT
Output of input signal for display.
l)
POWER OUT
Power output.
m) POWER IN
Power input.
7
Remote Control Buttons
ENG
AUTOMATIC SWITCH-OFF
VCR/DVD FUNCTIONS;
- STOP (Stop)
- REWIND (Rew)
- PLAY/PAUSE (Play/Pause)
- FAST FORWARD (FF)
Power
POWER ON/OFF
PIP FUNCTIONS;
- PIP ACTIVATING OR DEACTIVATING
(PIP ON)
- SWAPPING THE MAIN AND THE SUB
PICTURE (Swap)
- SELECTING THE LOCATION OF SUB
PICTURE (Locate)
- SELECTING THE CHANNEL OF SUB
PICTURE (P▲/▼)
- SETTING THE SIZE OF SUB PICTURE
(Size)
- SELECTING THE INPUT SOURCE
(Source)
- SCANNING THE CHANNEL OF SUB
PICTURE (Scan)
NUMERIC BUTTONS
MAKE THE REMOTE CONTROL WORKS
FOR TV, VCR, CABLE, DVD PLAYER
EXTERNAL INPUT SELECTION/
TELETEXT HOLD
ONE, TWO, OR THREE-DIGIT CHANNEL
SELECTION
TEMPORARY SOUND SWITCH OFF
NEXT CHANNEL/
TELETEXT NEXT PAGE
MENU DISPLAY/
TELETEXT INDEX
CONTROL THE CURSOR IN THE MENU
VOLUME DECREASE
VOLUME INCREASE
CHANGE CONFIRMATION
TELETEXT SUB CODE
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
DISPLAY INFORMATION/
TELETEXT REVEAL
PICTURE SIZE/
TELETEXT SIZE SELECTION
TELETEXT ON
VIDEO & TEXT
MIX
TELETEXT OFF
(Refer to page 45 for details)
FASTEXT TOPIC SELECTION
SOUND MODE SELECTION/
TELETEXT CANCEL
STILL THE MAIN PICTURE
➢
In the PIP mode, the main and sub
pictures are stilled at the same time.
SOUND EFFECT SELECTION
PICTURE EFFECT SELECTION
➢
8
It is possible that the work of the transmitter is dull or not operated normally
if the light of the Bulb is on around the PDP.
Inserting the Batteries in the Remote Control
ENG
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆ + on the battery against + on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
➢
Do not mix battery types, i.e. alkaline and manganese.
Installing the Display on the Wall Attachment Panel
➢
Wall attachment panel is sold separately. Check with your dealer.
Installation Notes
◆ Do not install the PDP on any place other than vertical walls.
◆ To protect the performance of the PDP and prevent troubles, avoid the
followings:
-
Do not install next to smoke and fire detectors.
Do not install in an area subjected to vibration or high voltage.
Do not install on the wall.
Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
continued...
9
Installing the Display on the Wall Attachment Panel
➢
ENG
Wall attachment panel is sold separately. Check with your dealer
1
Check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to
support the PDP, strengthen the wall before installation.
2
Fix the wall attachment panel on the
wall using bolts as shown in the figure:
Fixing bolts must protrude from the
wall appox. 1.5 cm.
3
Using the wall attachment panel, you may adjust the angle of the display from 0 to 20 degrees. The
angle can be set in 5 stages with 5 degrees of distance each using the angle control holes on the sides
of the panel.
When the angle has
been set to 15 degrees.
When the angle has
been set to 5 degrees.
Angle control holes
5 degrees of tilt
10 degrees of tilt
15 degrees of tilt
No tilt
20 degrees of tilt
10
When the panel hasn't
been tilted.
Installing the Display on the Wall Attachment Panel
ENG
4
Remove four large screws from the rear side of the display.
Insert the bolts, dish-type washers, and insulation rubber
into the four screw-holes as shown in the figure:
Bolt
Insulation rubber
5
Hang the protruding plastic part on
the rear of the PDP up the groove on
the top of the wall attachment panel.
Then, lift down the PDP. (Do not lift
down the PDP with too much force.
The protruding plastic part might be
taken off.)
Œ
´
11
Separating the Display from the Wall Attachment Panel
ENG
After lifting the PDP up, pull it forward and remove it from the wall attachment panel.
Œ
´
12
Connecting Speakers
ENG
Connecting PDP and Speakers
Fix the bracket onto the guide
pole located on the rear of
speaker and fasten the screws.
After removing the three
screws on the PDP, clamp the
speaker and the PDP together
and fasten the screws.
Guide pole
Guide pole
Connecting Stand and Speakers
➢
Guide pole
When moving your PDP, do NOT hold the
speaker connected to your PDP.
It may damage the bracket clamping the
speaker and your PDP together and
result in a drop of your PDP and a risk of
personal damage and injury.
Rear of the Media Station
Connect the speaker audio cable to the external speaker output
jack on the rear of the Media Station matching the “+” and “-” ends
of the cable with the diagram on the Media Station.
Rear of the PDP
➣
◆ The speakers MUST have more than 15watts rating (impedance 8Ω).
◆ The ferrite cores are used to attenuate undesired signals. When you connect the speaker wire to the
EXTERNAL SPEAKER OUT (8Ω) connector, bind the speaker wire round the ferrite core to secure it.
13
Connecting to an Aerial (or Cable Television Network)
ENG
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
Rear of the
Media Station
or
Cable Television
Network
14
1
In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the Media Station.
2
If you are using an indoor aerial, you may need to turn it when
tuning your television until you obtain a picture that is both sharp
and clear.
For further details, refer to:
◆ “Storing Channels Automatically” on page 20
◆ “Storing Channels Manually” on page 22
Switching On and Off
ENG
1
Plug the mains lead of the PDP and Media Station into an appropriate socket.
2
Connect the video cable between the DISPLAY SIGNAL IN on the rear of the PDP and the DISPLAY
SIGNAL OUT on the rear of the Media Station.
3
Press the POWER button on the front panel of the Media Station or remote control to switch the display on.
☛
Rear of the PDP
- Power cord
- Video Cable
Rear of the Media Station
◆ Do not connect the power cord
between PDP and Media Station.
Otherwise, the EMI characteristic will
become worse because power input
and output signals interrupt each other.
◆ The ferrite core is used to attenuate
undesired signals. When you connect
the power cord to the POWER IN
connector on the rear of the Media
Station, bind the power cord round the
ferrite core to secure it.
- Power cord
If your Media Station isn’t turned on when the power button is
pressed, please check if the “TV” mode has been chosen by
pressing the “Select” button.
15
Becoming Familiar with the Remote Control
ENG
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Display the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
Button
Viewing Function
Menu Function
Used to display the next
stored channel.
-
P
Used to display the
previous stored channel.
-
to
Used to display the corresponding channels.
For double digit channels, the second digit must be
pushed immediately after the first. Failure to do this will
result in a single digit channel being displayed.
Power
P
-/--/---
Mute
Menu
16
➢
Used to select a channel numbered ten or over.
Press this button, and enter the two or three-digit channel
number.
Used to increase the
volume.
-
Used to decrease the
volume.
-
Used to switch the sound off temporarily.
To turn the sound back on, press this button again, or
press the - or + button.
➣
Used to display the
on-screen menu system.
Used to return to the previous
menu or normal viewing.
-
Used to:
◆ Display a submenu
containing selections for
the current menu option
◆ Search forwards/
backwards manually for
channels
◆ Increase/decrease a
menu option value
-
Used to confirm your choice.
Setting up your Remote Control
ENG
1
Turn off your VCR, Cable box, or DVD.
2
Press the Select button repeatedly to activate another component
(VCR, Cable, DVD).
Example: If you want to program the remote control to operate
your VCR, make sure that the VCR LED is
illuminated.
3
Press the Power button on the remote control. The component you
select should turn on. If it turns on, your remote control is now set
correctly.
4
Once your remote control is set up, press the Select button any
time you want to use the remote control to operate your VCR,
Cable box, or DVD.
➣
◆ When your remote control is in the VCR, Cable, or DVD
mode, the volume buttons still control your Media
Station’s volume.
◆ When your remote control is in the TV or Cable mode,
the VCR control buttons (PLAY, PAUSE, etc.) still
operate your VCR.
17
Plug and Play
ENG
When the Media Station is initially powered ON, several basic
customer settings proceed automatically and subsequently. The
following settings are available.
1
If the Media Station is in Standby mode, press the Power button on
the remote control.
Result:
2
Plug & Play
Select the appropriate language by moving the joystick left or
right. Press the MENU button.
Result:
English
Language
Select
Menu
3
➢
Antenna input check
Area
Select
Area
ASIA / W.EUROPE
Menu
Store
ASIA / W.EUROPE P 6
44 MHz
1%
Menu
Enjoy your watching
18
The following areas are available.
ASIA / W.EUROPE - CIS / E.EUROPE - CHINA HONGKONG / UK - AUSTRALIA - SOUTH AFRICA AMERICA
To start the store, press the joystick button.
Result:
5
The message Antenna input check is displayed.
It flickers for a little while, and then the Area menu is
displayed. Make sure that the antenna is connected to
the Media Station.
Select your area by moving the joystick left or right.
Result:
4
The message Plug & Play is displayed. It flickers for
a little while, and then the Language menu is
automatically displayed.
The search is start. During searching, the status bar is
displayed and the search will end automatically.
To stop the search before it has finished or return to normal
viewing, press the MENU button.
When it has finished, the message Enjoy your watching is
displayed, and then the channel which has been stored will be
activated.
Choosing Your Language
ENG
When you start using your PDP for the first time, you must select
the language which will be used for displaying menus and
indications.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the Function is selected.
The options available in the Function group are
Result:
displayed.
3
Press the joystick button.
The Language is selected.
Result:
4
Select the appropriate language by moving the joystick left or
right.
Function
English
Language
Time
Size
Image Lock
Melody
Move
Normal
On
Select
19
Menu
Storing Channels Automatically
ENG
Channel
ASIA / W.EUROPE
Area
Auto Store
Manual Store
Channel Sort
You can scan for the frequency ranges available to you, (availability
depends on your country). Automatically allocated programme
numbers may not correspond to actual or desired programme
numbers. However you can sort numbers manually and clear any
channels you do not wish to watch.
Channel Edit
Fine Tune
Move
Select
Menu
Channel
1
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the Channel is selected.
The options available in the Channel group are
Result:
displayed.
3
Press the joystick button.
The Area is selected.
Result:
4
Select your area by moving the joystick left or right.
The following areas are available.
Result:
ASIA / W.EUROPE - CIS / E.EUROPE - CHINA HONGKONG / UK - AUSTRALIA - SOUTH AFRICA AMERICA
5
Move the joystick up or down until the Auto Store is selected.
Press the joystick button to start the search.
The search will end automatically. Channels are sorted
Result:
and stored in an order which reflects their position in
the frequency range, (with lowest first and highest last).
The programme originally selected is then displayed.
ASIA / W.EUROPE
Area
Auto Store
Manual Store
Channel Sort
Channel Edit
Fine Tune
Move
Area
Enter
Menu
ASIA / W.EUROPE P 6
44 MHz
1%
Menu
➣
6
20
To stop the search before it has finished, press the Menu
button.
When the channels have been stored, you can:
◆ Sort them in the order required (see page 21)
◆ Assign a name to the stored channels (see page 24)
◆ Add and erase the channels (see page 24)
◆ Lock the channels (see page 24)
◆ Activate the LNA (Low Noise Amplifier) feature (see page 24)
◆ Fine tune channel reception if necessary (see page 25)
Sorting the Stored Channels
ENG
This operation allows you to change the programme numbers of
stored channels. This operation may be necessary after using auto
store. You can delete the channels you do not want to keep.
Channel
ASIA / W.EUROPE
Area
Auto Store
Manual Store
Channel Sort
1
2
3
Press the MENU button.
The main menu is displayed.
Result:
Channel Edit
Fine Tune
Move
Move the joystick up or down until the Channel is selected.
The options available in the Channel group are
Result:
displayed.
Press the joystick button.
4
Move the joystick up or down until the Channel Sort is selected.
Press the joystick button.
The options available in the Channel Sort group are
Result:
displayed with the From is selected.
5
Select the channel number that you wish to change by moving the
joystick left or right.
6
Move the joystick up or down until the To is selected. Select the
new channel number which you wish to identify by moving the
joystick left or right.
Enter
Channel Sort
From
P 1
To
P 3
Store
Move
?
Select
8
Channel Sort
P 1
To
P 3
To confirm the exchange of channel numbers, select the Store by
moving the joystick up or down. Set to OK by moving the joystick
left or right.
The selected channel is exchanged with the one
Result:
previously stored to the chosen number.
For all the channels to move to the required channel numbers,
repeat steps 5 to 7 after selecting the From by moving the joystick
up or down.
Menu
From
?
Store
7
Menu
Move
Select
Menu
Channel Sort
From
P 3
To
P 1
Store
OK
Move
Select
21
Menu
Storing Channels Manually
ENG
Channel
ASIA / W.EUROPE
Area
You can store up to television channels, including those received
via cable networks.
Auto Store
When storing channels manually, you can choose:
Manual Store
Channel Sort
◆ Whether or not to store each of the channels found
Channel Edit
◆ The programme number of each stored channel which
you wish to identify
Fine Tune
Move
Enter
Menu
Manual Store
Program No.
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the Channel is selected.
The options available in the Channel group are
Result:
displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Manual Store is selected.
Press the joystick button.
The options available in the Manual Store group are
Result:
displayed with the Program No. is selected.
5
To assign a programme number to a channel, find the correct
number by moving the joystick left or right.
6
Move the joystick up or down until the Colour System is selected.
Select the broadcasting system required by moving the joystick
left or right.
The following colour systems are available.
Result:
Auto - PAL - SECAM - NTSC4.43 - NTSC3.58
7
Move the joystick up or down until the Sound System is selected.
Select the sound system required by moving the joystick left or
right.
The following sound systems are available.
Result:
B/G - D/K - I - M
8
For all the channels to move to the required channel numbers,
repeat steps 5 to 7 after selecting the Program No. by moving the
joystick up or down.
1
Colour System
Auto
Sound System
B/G
Freq. Search
187 MHz
Channel No.
C 2
Store
Move
1
?
Select
Menu
Manual Store
Program No.
1
Colour System
Auto
Sound System
B/G
Freq. Search
187 MHz
Channel No.
C 2
Store
Move
?
Select
Menu
Manual Store
Program No.
1
Colour System
Auto
Sound System
B/G
Freq. Search
187 MHz
Channel No.
C 2
Store
Move
?
Select
Menu
continued...
22
Storing Channels Manually
ENG
9
If you know the number of the channel to be stored...
◆ Move the joystick up or down until the Channel No. is
selected. Move the joystick right.
◆ Select the C (Air channel) or S (Cable channel) by moving the
the joystick up or down. Move the joystick right.
◆ Select the required number by moving the the joystick up or
down.
➣
10
11
12
Manual Store
Program No.
1
Colour System
Auto
Sound System
B/G
Freq. Search
187 MHz
Channel No.
C 2
Store
Move
?
Select
If no sound or abnormal sound, re-select the sound
system required.
If you do not know the channel numbers, select the Freq.
Search by moving the the joystick up or down. Move the joystick
right to start the search.
The tuner scans the frequency range until the first
Result:
channel or the channel that you selected is received
on your screen.
To store the channel and associated programme number, select
the Store by moving the the joystick up or down. Set to OK by
moving the joystick left or right.
Repeat Steps 9 to 11 for each channel to be stored.
Manual Store
Program No.
1
Colour System
Auto
Sound System
B/G
Freq. Search
187 MHz
Channel No.
C 2
Store
Move
?
Select
1
Auto
Sound System
Channel mode
◆ P (Programme mode): When completing tuning, the
broadcasting stations in your area have been assigned to
position numbers from P00 to max P99. You can select a
channel by entering the position number in this mode.
Menu
Manual Store
Program No.
Colour System
☛
Menu
B/G
Freq. Search
187 MHz
Channel No.
C 2
Store
Move
OK
Select
◆ C (Real channel mode): You can select a channel by
entering the assigned number to each air broadcasting station
in this mode.
◆ S (Cable channel mode): You can select a channel by
entering the assigned number for each cable channel in this
mode.
23
Menu
Editing the Channels
ENG
Channel
ASIA / W.EUROPE
Area
1
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the Channel is selected.
The options available in the Channel group are
Result:
displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Channel Edit is selected.
Press the joystick button.
The options available in the Channel Edit group are
Result:
displayed with the current channel is selected.
5
Select a programme number to be edited by moving the joystick
up or down.
6
To assign a new name, select the Name by moving the joystick left
or right. Press the joystick button.
7
Move the joystick up or down to select a letter (A~Z), a number
(0~9) or a symbol (-, space). To move on the previous or next
letter, move the joystick left or right.
8
You can add or erase the channels you chosen from the channels
you scanned. Select the Add/Erase by moving the joystick left or
right. If necessary, select the Added or Erased by moving the
joystick up or down.
9
You can prevent unauthorised users, such as children, from
watching unsuitable programme. Select the Child Lock by
moving the joystick left or right. If necessary, select the On to lock
the channel required by moving the joystick up or down.
10
Move the joystick left or right until the LNA is selected. This feature
is very useful in the situation that the TV is used in a weak signal
and amplifies the TV signal in the weak signal area, but not noise.
If necessary, select the On or Off by moving the joystick up or
down.
Auto Store
Manual Store
Channel Sort
Channel Edit
Fine Tune
Move
Enter
Menu
Channel Edit
Name
Prog.
No.
0
1
2
3
4
---------------------
Adjust
Add
Erase
Added
Added
Added
Added
Added
Move
Child
Lock
Off
Off
Off
Off
Off
LNA
Off
Off
Off
Off
Off
Menu
Channel Edit
Prog.
No.
0
1
2
3
4
Name
---------------------
Adjust
Add
Erase
Added
Added
Added
Added
Added
Move
Child
Lock
Off
Off
Off
Off
Off
LNA
Off
Off
Off
Off
Off
Menu
Channel Edit
Name
Prog.
No.
0
1
2
3
4
---------------------
Adjust
Add
Erase
Added
Added
Erased
Added
Added
Move
Child
Lock
Off
Off
Off
Off
Off
LNA
Off
Off
Off
Off
Off
Menu
Channel Edit
Prog.
No.
0
1
2
3
4
Name
---------------------
Adjust
Add
Erase
Added
Added
Erased
Added
Added
Move
Child
Lock
Off
Off
On
Off
Off
LNA
Off
Off
Off
Off
Off
Menu
Channel Edit
Prog.
No.
0
1
2
3
4
Name
Adjust
---------------------
Add
Erase
Added
Added
Erased
Added
Added
Move
24
Child
Lock
Off
Off
On
Off
Off
LNA
Off
Off
On
Off
Off
Menu
Fine Tuning Channel Reception
ENG
If the reception is clear, you do not have to fine tune the channel,
as this is done automatically during the search and store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
Channel
ASIA / W.EUROPE
Area
Auto Store
Manual Store
Channel Sort
Channel Edit
1
2
Press the MENU button.
The main menu is displayed.
Result:
Move the joystick up or down until the Channel is selected.
The options available in the Channel group are
Result:
displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Fine Tune is selected.
Press the joystick button.
The options available in the Fine Tune group are
Result:
displayed with the Fine Tune is selected.
5
To obtain a sharp and clear picture and good sound quality, move
the joystick left or right until you reach the setting.
6
To memorise adjusted picture or sound, select the Store by
moving the joystick up or down. Set to OK by moving the joystick
left or right.
7
To erase adjusted picture or sound, select the Erase by moving
the joystick up or down. Set to OK by moving the joystick left or
right.
Fine Tune
Move
Menu
Enter
Fine Tune
0
Fine Tune
Store
?
Erase
?
Move
Adjust
Menu
Fine Tune
0
Fine Tune
Store
OK
Erase
?
Move
Select
Menu
Fine Tune
0
Fine Tune
Store
?
Erase
OK
Move
Select
25
Menu
Changing the Picture Standard
ENG
Picture
Custom
Mode
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone
Move
Normal
Select
You can select the picture mode which best corresponds to your
viewing requirements.
1
Press the MENU button.
The Picture menu is displayed.
Result:
2
Press the joystick button to enter the picture menu.
The Mode is selected.
Result:
3
To select the picture effect which best corresponds to your viewing
requirements, move the joystick left or right.
The following modes are available depending on the
Result:
input source.
◆ Custom - Dynamic - Standard - Movie
◆ Custom - High - Middle - Low
(PC or DVI Mode)
Menu
PC Mode
Picture
Middle
Mode
Contrast
Brightness
Sharpness
Colour Tone
Move
Select
➣
Menu
You can select these options by simply pressing the
P.STD (Picture Standard) button on the remote control.
Adjusting the Picture Settings
Picture
Custom
Mode
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone
Move
Normal
Adjust
Menu
Your PDP has several settings which allow you to control picture
quality.
1
Press the MENU button.
The Picture menu is displayed.
Result:
2
Press the joystick button to enter the picture menu.
3
Select a option to be adjusted by moving the joystick up or down.
4
To adjust the Contrast, Brightness, Sharpness, Colour, or
Tint (NTSC only), move the joystick left or right.
The horizontal bar is displayed. Move the joystick left
Result:
or right until you reach the setting.
◆ In the PC mode, you can not adjust the Colour
and Tint,
5
To adjust the Colour Tone, move the joystick left or right.
The following options are available.
Result:
Normal - Cool 1 - Cool 2 - Warm 2 - Warm 1
Picture
Custom
Mode
Contrast
Brightness
Sharpness
Colour
Tint
Colour Tone
Move
Normal
Select
Menu
➣
26
If you make any changes to these settings, the picture
mode is automatically switched to the Custom.
Changing the Picture Size
ENG
You can select the picture size which best corresponds to your
viewing requirements.
1
2
Press the MENU button.
The main menu is displayed.
Result:
Move the joystick up or down until the Function is selected.
The options available in the Function group are
Result:
displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Size is selected.
5
Select a your required size by moving the joystick left or right.
The following modes are available depending on the
Result:
input source.
Function
English
Language
Time
Size
Image Lock
Melody
Move
Normal
On
Select
◆ Wide - Panorama - Zoom 1 - Zoom 2 Stretch - 14:9 - Normal
◆ Standard - Full - Normal
(PC or DVI Mode)
➣
◆ You can select these options by simply pressing the
P.Size (Picture Size) button on the remote control.
◆ If you watch a still image or the 4:3 mode for a long
time, image may be burned onto the screen, view the
PDP in Wide or Panorama mode as possible.
Freezing the Current Picture
Press the “Still” button to freeze the current picture. To return to
normal viewing, press it again.
➣
In the PIP mode, the main and sub pictures are stilled at
the same time.
27
Menu
Adjusting the Picture Settings (PC or DVI Mode)
➢
ENG
Colour Tone
Custom
Mode
R
G
B
Move
Select
Move
1
Press the MENU button.
The Picture menu is displayed.
Result:
2
Press the joystick button to enter the picture menu.
3
Select a option (Contrast, Brightness, Sharpness) to be
adjusted by moving the joystick up or down.
The horizontal bar is displayed. Move the joystick left
Result:
or right until you reach the setting.
4
Move the joystick up or down until the Colour Tone is selected.
Press the joystick button.
The options available in the Colour Tone group are
Result:
displayed with the Mode is selected
5
Select the required mode by moving the joystick left or right.
The following modes are available.
Result:
Custom - Colour l - Colour 2 - Colour 3
6
To control the colour, select a option (R-red, G-green, B-blue) by
moving the joystick up or down. Move the joystick left or right.
The horizontal bar is displayed. Move the joystick left
Result:
or right until you reach the setting.
Menu
Colour Tone
Custom
Mode
R
G
B
Adjust
28
Preset to the PC mode by using the Source button.
Menu
Setting the Picture (PC Mode)
➢
Preset to the PC mode by using the Source button.
ENG
1
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the Function is selected.
The options available in the Function group are
Result:
displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Image Lock is selected.
Press the joystick button.
The options available in the Image Lock group are
Result:
displayed.
5
Select the required option (Frequency or Phase) to be adjusted by
moving the joystick up or down. Move the joystick left or right until
you reach the setting.
6
Move the joystick up or down until the Position is selected.
Press the joystick button.
7
Move the required position by using the joystick.
8
9
10
Press the MENU button.
The options available in the Image Lock group are
Result:
displayed again.
To replace all image settings with the factory default values, select
the Recall by moving the joystick up or down. Set to OK by
moving the joystick left or right.
Result:
The options available in the Image Lock group are
displayed again.
To adjust the screen quality and position automatically, select the
Auto Adjustment by moving the joystick up or down. Press the
joystick button.
The Auto Adjustment is displayed. The screen quality
Result:
and position are automatically adjusted.
Function
English
Language
Time
Size
Image Lock
Melody
Normal
On
Move
Menu
Enter
Image Lock
50
65
Frequency
Phase
Position
Recall
Auto Adjustment
Move
?
Adjust
Menu
Image Lock
50
65
Frequency
Phase
Position
Recall
Auto Adjustment
?
Menu
Enter
Move
Position
Up
Left
Right
Down
Menu
Adjust
Image Lock
50
65
Frequency
Phase
Position
Recall
Auto Adjustment
Move
OK
Select
Menu
Image Lock
50
65
Frequency
Phase
Position
Recall
Auto Adjustment
Move
?
Enter
29
Menu
Changing the Sound Standard
ENG
You can select the type of special sound effect to be used when
watching a given broadcast.
Sound
Custom
Mode
Equalizer
Auto Volume
Source
Sound Mode
Dolby Surround
Headphone
Move
Off
Main
Stereo
1
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the Sound is selected.
The options available in the Sound group are displayed.
Result:
3
Press the joystick button.
The Mode is selected.
Result:
4
To select the type of special sound effect to be used when
watching a given broadcast, move the joystick left or right.
The following modes are available.
Result:
Custom - Standard - Music - Movie - Speech
Menu
Select
➣
You can select these options by simply pressing the S.STD
(Sound Standard) button on the remote control.
Adjusting the Sound Settings
The sound settings can be adjusted to suit your personal preferences.
Sound
Custom
Mode
Equalizer
Auto Volume
Source
Sound Mode
Dolby Surround
Headphone
Move
Off
Main
Stereo
Menu
Enter
1
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the Sound is selected.
The options available in the Sound group are displayed.
Result:
3
Press the joystick button.
4
Move the joystick up or down until the Equalizer is selected.
Press the joystick button.
5
Select a your required option by moving the joystick left or right.
6
Move the joystick up or down until you reach the setting.
Equalizer
R
L
100Hz 300Hz
Adjust
Move
30
1kHz
3kHz
10kHz
Menu
➣
If you make any changes to these settings, the sound
mode is automatically switched to the Custom.
Adjusting the Volume Automatically
ENG
Each broadcasting station has its own signal conditions, and so it is
not easy for you to adjust the volume every time the channel is
changed. This feature lets you automatically adjust the volume of
the selected channel by lowering the sound output when the
modulation signal is high or by raising the sound output when the
modulation signal is low.
1
Press the MENU button.
Result:
2
Sound
Mode
Equalizer
Auto Volume
Source
Sound Mode
Dolby Surround
Headphone
Move
Custom
On
Main
Stereo
Select
The main menu is displayed.
Move the joystick up or down until the Sound is selected.
Result:
The options available in the Sound group are displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Auto Volume is selected.
5
Select On by moving the joystick left or right.
31
Menu
Selecting the Sound Mode
ENG
Sound
Mode
Equalizer
Auto Volume
Source
Sound Mode
Dolby Surround
Headphone
Move
Custom
Off
Main
Stereo
Depending on the particular program being broadcast, you can
display and control the processing and output of the audio signal.
When power is switched on, the mode is automatically preset to
either “Dual-I ” or “Stereo”, depending on the current transmission.
1
Select
Press the MENU button.
Result:
Menu
2
The main menu is displayed.
Move the joystick up or down until the Sound is selected.
Result:
The options available in the Sound group are displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Sound Mode is selected.
5
Select the required sound mode by moving the joystick left or
right.
Type of broadcast
On-screen indication
(FM) Mono
Mono
(FM) Stereo
Stereo - Mono
(FM) Dual
Dual I - Dual II
NICAM Mono
NICAM Mono - Mono
NICAM Stereo
NICAM Stereo - Mono
NICAM Dual
➣
➣
NICAM Dual I - NICAM Dual II - Mono
You can select these options by simply pressing the
S.Mode (Sound Mode) button on the remote control.
◆ If the receiving conditions deteriorate, listening will
be easier if the mode is set to the Mono.
◆ If the stereo signal is weak and an automatic
switching occurs, then switch to the Mono.
◆ When receiving a mono sound in the AV mode,
connect to the “AUDIO-L” input connector on the
panel of the television. If the mono sound comes out
only from left speaker, press the S.Mode button.
32
Setting the Dolby Surround
ENG
This feature allows you enjoy Dolby Pro Logic surround effect fully
with only surround speakers are connected to the Media Station.
Rear of the Media Station
This allows various modes for the main, center, surround and
woofer speakers to be selected.
1
Press the MENU button.
Result:
2
The main menu is displayed.
Move the joystick up or down until the Sound is selected.
Result:
The options available in the Sound group are displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Dolby Surround is
selected. Press the joystick button.
Result:
5
➣
7
Custom
Move
Off
Main
Stereo
The following modes are available.
Off - Virtual - Pro Logic
◆ When you select the Pro Logic, the following settings
can be adjusted.
◆ For further details of sound output depending on the
each options, refer to page 34.
Dolby Surround
Pro Logic
Phantom
Mode
Mode
Center
Rear
Time Delay
Test Tone
Move
1
1
15ms
Off
Result:
➢
The following modes are available.
Normal - Phantom - Wide
Manufactured under license from Dolby Laboratories.
Menu
Select
Move the joystick up or down until the Mode is selected in the Pro
Logic menu.
Select the required mode by moving the joystick left or right.
Menu
Enter
Select the Pro Logic in the Dolby Surround mode by moving the
joystick left or right.
Result:
6
The options available in the Dolby Surround group
are displayed with the Mode is selected.
Sound
Mode
Equalizer
Auto Volume
Source
Sound Mode
Dolby Surround
Headphone
Dolby Surround
Pro Logic
Phantom
Mode
Mode
Center
Rear
Time Delay
Test Tone
Move
1
1
15ms
Off
Select
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
33
Menu
Setting the Dolby Surround
ENG
Input Signal
Main
Left
Off
Stereo
Mono
✔
✔
✔
✔
✔
✔
Virtual
Stereo
Mono
✔
✔
✔
✔
✔
✔
Pro Logic - Normal
Stereo
Mono
✔
- Phantom
Stereo
Mono
✔
✔
- Wide
Stereo
Mono
✔
Surround Mode
Center
✔
✔
✔
✔
Main
Right
Surround
Right
Surround
Left
Sub
Woofer
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ; Sound
➢
34
If the center speaker is not connected, no sound will be output in
Normal and Wide modes when inputting a mono signal.
Adjusting the Dolby Pro Logic Preferences
ENG
The following Dolby Surround settings can be adjusted to suit your
personal preferences.
◆ Volume of the center and rear speakers
◆ Delay time for the rear speakers (between15 and 30 ms)
◆ Activation/deactivation of the test tone to simulate the
volume on each speaker
Dolby Surround
Move
1
1
1
15ms
Off
Adjust
Press the MENU button.
Result:
2
Pro Logic
Phantom
Mode
Mode
Center
Rear
Time Delay
Test Tone
The main menu is displayed.
Move the joystick up or down until the Sound is selected.
Result:
The options available in the Sound group are displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Dolby Surround is
selected. Press the joystick button.
Result:
The options available in the Dolby Surround group
are displayed with the Mode is selected.
5
Select the Pro Logic by moving the joystick left or right.
6
Move the joystick up or down to select a option (Center, Rear,
Time Delay, Test Tone) to be adjusted. Change a setting by
moving the joystick left or right.
35
Menu
Adjusting the Headphone Preferences
ENG
You can adjust the headphone settings to suit your preferences.
The following headphone settings are available:
Front of the Media Station
◆ Volume, Bass, Treble, Balance.
1
Press the MENU button.
Result:
2
Move the joystick up or down until the Sound is selected.
Result:
Press the joystick button.
4
Move the joystick up or down until the Headphone is selected.
Press the joystick button.
Custom
Move
Result:
Off
Main
Stereo
5
50
Adjust
36
Move the joystick up or down to select a option to be adjusted.
Change a setting by moving the joystick left or right.
➣
10
10
10
50
L
Move
The options available in the Headphone group are
displayed.
Menu
Enter
Headphone
Volume
Bass
Treble
Balance
The options available in the Sound group are displayed.
3
Sound
Mode
Equalizer
Auto Volume
Source
Sound Mode
Dolby Surround
Headphone
The main menu is displayed.
R
Menu
Prolonged use of headphones at a high volume may
damage your hearing.
Hearing the Melody Sound
ENG
You can hear clear melody sound when power is switched on or off.
1
2
Press the MENU button.
The main menu is displayed.
Result:
Move the joystick up or down until the Function is selected.
The options available in the Function group are
Result:
displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Melody is selected.
5
Select the required option (On or Off) by moving the joystick left or
right.
Function
Language
Time
Size
Image Lock
Melody
English
Normal
On
Move
Menu
Select
Setting the Current Time
You can set the clock so that the PDP will:
Function
◆ Switch on automatically and tune to the channel of your
choice at the time you select
◆ Switch off automatically at the time you select.
➣
1
2
If you disconnect the power cord, the clock will be reset.
You have to set the clock again.
English
Language
Time
Size
Image Lock
Melody
Normal
On
Move
Press the MENU button.
The main menu is displayed.
Result:
Move the joystick up or down until the Function is selected.
The options available in the Function group are
Result:
displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Time is selected. Press the
joystick button.
The options available in the Time group are displayed
Result:
with the Clock is selected.
5
To...
Move the joystick...
Move to the each option
(hour, minute and am/pm)
left or right.
Adjust the each option
up or down.
Menu
Enter
Time
Clock
09 : 35 am
On Time
12 : 00 am Off
Off Time
12 : 00 am Off
Sleep Timer
Off
On Time Program
P 1
10
On Time Volume
Move
Select
37
Menu
Switching On and Off Automatically
ENG
You can switch on or off automatically at the time you select.
Also you can select the channel and volume level when it will be
switched on.
Function
English
Language
Time
Size
Image Lock
Melody
Normal
On
1
Press the MENU button.
Result:
Move
2
Clock
09 : 35 am
On Time
06 : 30 am On
Off Time
12 : 00 am Off
Sleep Timer
Off
On Time Program
P 1
The options available in the Function group are
displayed.
3
Press the joystick button.
4
Move the joystick up or down until the Time is selected. Press the
joystick button.
10
On Time Volume
Result:
Menu
Select
Move the joystick up or down until the Function is selected.
Result:
Time
Move
The main menu is displayed.
Menu
Enter
The options available in the Time group are displayed.
5
Move the joystick up or down until the On Time is selected.
Set the time which you wish to be switched on.
6
Move the joystick up or down until the Off Time is selected.
Set the time which you wish to be switched off.
7
Move the joystick up or down until the On Time Program is
selected. Select the channel when it will be switched on by moving
the joystick left or right.
8
Move the joystick up or down until the On Time Volume is
selected. Set the volume level when it will be switched on by
moving the joystick left or right.
Time
Clock
09 : 35 am
On Time
06 : 30 am On
Off Time
10 : 30 pm On
180 min.
Sleep Timer
P 1
On Time Program
10
On Time Volume
Move
Menu
Select
Time
Clock
09 : 35 am
On Time
06 : 30 am On
Off Time
10 : 30 pm On
180 min.
Sleep Timer
P 1
On Time Program
10
On Time Volume
Move
Adjust
38
Menu
Setting the Sleep Timer
ENG
You can select a time period of between 15 and 360 minutes after
which the PDP automatically switches to Standby mode.
1
Press the MENU button.
Result:
2
English
Normal
On
The main menu is displayed.
Move the joystick up or down until the Function is selected.
Result:
Function
Language
Time
Size
Image Lock
Melody
Move
Menu
Enter
The options available in the Function group are
displayed.
Time
3
Press the joystick button.
4
Move the joystick up or down until the Time is selected. Press the
joystick button.
Clock
09 : 35 am
On Time
06 : 30 am On
Off Time
10 : 30 pm On
180 min.
Sleep Timer
P 1
On Time Program
Result:
5
The options available in the Time group are displayed.
Move the joystick up or down until the Sleep Timer is selected.
Select the preset time interval (15, 30, 45, 60, 90, 120, 150, 180,
210, 240, 270, 300, 330, 360) for staying on by moving the joystick
left or right.
10
On Time Volume
Move
Select
You can set the sleep timer by simply pressing the “Sleep” button
on the remote control.
1
Press the Sleep button on the remote control.
Result:
2
If the sleep timer is not yet set, Off is displayed.
Otherwise, the remaining time before which the
television switches to Standby mode is displayed.
Select the preset time interval for staying on by pressing the Sleep
button repeatedly.
39
Menu
Viewing the Picture in Picture (PIP)
ENG
You can display a sub picture within the main picture. In this way
you can monitor the input sources from any connected equipment.
PIP
On
TV
PIP
Source
Swap
Size
Locate
Program No.
Move
Large
P 1
1
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the PIP is selected.
The options available in the PIP group are displayed.
Result:
3
Press the joystick button.
The PIP is selected.
Result:
4
Set to On by moving the joystick left or right.
Menu
Select
➣
PIP
On
TV
PIP
Source
Swap
Size
Locate
Program No.
Move
5
Large
P 1
To select the external sources of sub picture, select the Source by
moving the joystick up or down. Move the joystick left or right.
The followings are available depending on the input
Result:
source.
◆ TV - AV 1 - AV 2 - AV 3 - AV 4 - AV 5
Menu
Select
➣
6
Power
PIP
On
TV
Source
Swap
Size
Locate
Program No.
Move
P 1
Power
40
◆ You can also do simply by pressing the Swap button.
◆ Not available depending on the input modes.
continued...
Large
Enter
You can also select these options simply by pressing the
Source button.
To interchange the main picture and sub picture, select the Swap
by moving the joystick up or down. Move the joystick left or right.
The main picture and sub picture are interchanged.
Result:
➣
PIP
You can also activate the PIP simply by pressing the PIP ON
button. To deactivate, press it again.
Menu
Viewing the Picture in Picture (PIP)
ENG
PIP
On
TV
PIP
7
To select the size of sub picture, select the Size by moving the
joystick up or down. Move the joystick left or right.
The following sizes are available depending on the
Result:
input source.
Source
Swap
Size
Locate
Program No.
Move
Large
P 1
Menu
Select
◆ Large - Small - Double 1 - Double 2
◆ Large - Small
➣
8
◆ If the system is different between the main picture and
the sub picture, the Double mode is not selected.
◆ In the PC mode, the size of sub picture may be different
depending on the type of PC Monitor and its resolution.
◆ You can also select these options simply by pressing the
Size button.
PIP
Source
Swap
Size
Locate
Program No.
To select the location of sub picture, select the Locate by moving
the joystick up or down. Move the joystick left or right.
You can move the sub picture counterclockwise.
Result:
➣
Move
Large
P 1
In the PC mode, select the Locate and press the joystick button.
The PIP Panning is displayed. You can move the sub
Result:
picture to your required location by pressing the
joystick left, right, up or down.
10
To select the channel of sub picture, select the Program No. by
moving the joystick up or down. Move the joystick left or right.
PC Mode
PIP Panning
◆ When the Source is set to TV, you can select the
channel of sub picture.
◆ You can also do simply by pressing the P▲ or P▼
button.
Exit
Adjust
PIP
On
TV
PIP
➣
Menu
Select
You can also do simply by pressing the Locate button.
9
➣
On
TV
PIP
The Scan button is used to scan every memorized
channel in order. To stop scanning, press it again.
Source
Swap
Size
Locate
Program No.
Move
Large
P 1
Select
Power
41
Menu
Listening to the Sound of the Sub Picture
ENG
Sound
Custom
Mode
Equalizer
Auto Volume
Source
Sound Mode
Dolby Surround
Headphone
Move
Off
Sub
Stereo
Select
During the PIP feature is activating, you can listen to the sound of the
sub picture.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Move the joystick up or down until the Sound is selected.
The options available in the Sound group are displayed.
Result:
3
Press the joystick button.
4
Move the joystick up or down until the Source is selected. Set to
Sub by moving the joystick left or right.
You can listen to the sound of the sub picture.
Result:
Menu
➣
42
To listen the sound of current main picture, set to Main.
Viewing Pictures From External Sources
ENG
Once you have connected up your various audio and video systems,
you can view the different sources by selecting the appropriate input.
1
Check that all the necessary connections have been made.
2
Press the Source button.
Result: The input sources available are displayed.
3
Move the joystick up or down until the required input source is
selected and press the joystick button.
➣
Front panel
If you change the external source while viewing, pictures
might take a short period of time to be switched.
TV
AV 1
AV 2
AV 3
AV 4
AV 5
Component 1
Component 2
DVI
PC
Move
Connected
Not Connected
Connected
Not Connected
Not Connected
Connected
Not Connected
Not Connected
Connected
Select
43
Exit
Teletext Feature
ENG
Most television channels provide written information services via
teletext. Information provided includes:
◆ Television programme times
◆ News bulletins and weather forecasts
◆ Sports results
◆ Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
➣
Teletext information is often divided between several
pages displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
➣
44
When a Teletext signal is present, the display panel (VFD)
on the front of Media Station will show “TTX ON”.
Displaying the Teletext Information
ENG
You can display Teletext information at any time on your PDP.
Teletext information to be displayed correctly,
☛ For
channel reception must be stable; otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
1
Select the channel providing the Teletext service by pressing the
P
or P
button.
2
Press the Text/Off button to activate the teletext mode.
The contents page is displayed. It can be redisplayed
Result:
at any time by pressing the
(index) button.
3
Press the Text/Off button again.
The screen will be split into two. This Double Teletext
Result:
feature lets you view the actual broadcast and teletext
information separately on the screen.
4
If you wish to display the actual broadcast and teletext information
on a single screen, press the Text/Off button again.
5
To exit from the teletext display, press the Text/Off button again.
45
Selecting Display Options
ENG
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display...
Press the...
◆ Hidden text
(answers to quiz games, for example)
(reveal)
◆ The normal screen
(reveal) again
◆ A secondary page by entering its number
(Time/Subcode)
46
◆ The broadcast when searching for a page
(cancel)
◆ The next page
(page up)
◆ The previous page
(page down)
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
(size)
• Once
• Twice
◆ The normal screen
• Three times
Selecting a Teletext Page
ENG
You can enter the page number directly by pressing the numeric
buttons on the remote control.
1
Enter the three-digit page number given in the content by
pressing the corresponding numeric buttons.
Result:
The current page counter is incremented and the
page is then displayed. If the selected page is linked
with several secondary pages, the secondary pages
are displayed in sequence. To freeze the display on a
given page, press the
(hold). Press the
(hold)
again to resume.
2
If the FASTEXT system is used by the broadcasting company,
the different topics covered on a Teletext page are color-coded
and can be selected by pressing the coloured buttons on the
remote control.
Press the coloured button corresponding to the topic that you wish
to select; the available topics are given on the status line.
Result:
The page is displayed with other colored information
that can be selected in the same way.
3
To display the previous or next page, press the corresponding
coloured button.
4
To display the subpage, see the following steps.
◆ Press the
(Time/Subcode) button.
Result:
The available subpages appear.
◆ Select the required sub-page. Sub-pages can be scrolled by
using the
or
button.
➣
Although a channel is changed by connecting an
external device, the information about the previous
channel may be displayed.
47
Connecting to the External Devices
ENG
The RCA connectors are used to input or output of external devices.
VCR
②
DVD
Rear of the Media Station
(Input/Output)
①
Decoder /
Video game device
③
Video disc player
Satellite receiver
➃
① This end can be fitted with three RCA connectors (VIDEO + AUDIO-L and R)
② If you have a second VCR and wish to copy cassettes tape, connect the source VCR to “AV 1” and the
target VCR to “MONITOR OUT” so that you can redirect the signal from source VCR to target VCR.
③ If you have a decoder, connect the decoder to the VCR and the VCR to the Media Station.
➃ “MONITOR OUT” is used for displaying the current picture to an external device. When you wish to record
the current picture, connect the VCR to “MONITOR OUT”.
➣
“MONITOR OUT” is available only with the source of RF, AV 1, AV 2, AV 3, AV 4 and AV 5.
The other mode is not available.
Camcorder
Front of the Media Station
(Input)
Video disc player
Video game device
☛
48
Whenever you connect an audio or video system to your
Media Station, ensure that all elements are switched off.
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
Connecting to the DVD Input
ENG
The RCA connectors are used for equipment with a DVD output. (480i/480p/576i/576p)
Rear of the Media Station
DVD
Connecting to the S-Video Input
The S-VIDEO and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the Media Station
①
and
Front of the Media Station
Camcorder
VCR
and
① To play pictures and sound, both the S-VIDEO and RCA connectors must be used.
49
Connecting to the Audio Output
ENG
The “SURROUND OUT” and “AUDIO OUT” connectors are used for equipment, such as an audio
system or external amplifier (to take full advantage of the Surround sound effect).
Rear of the Media Station
Audio System/
External Amplifier
Connecting to the DVI Input
The “DVI IN” and RCA (AUDIO-L/R) connectors are used for equipment with a DVI output.
Rear of the Media Station
Personal Computer
and
➢
The “DVI IN” does not support the Analog R (red), G (green) and B (blue) signals.
50
Connecting to the PC Input
ENG
The “PC IN” and RCA (AUDIO-L/R) connectors are used for interfacing with your PC.
Rear of the Media Station
Personal Computer
and
☛
Setting up Your Display Plug and Play
Our adoption of the new VESA® Plug and Play solution
eliminates complicated and time consuming setup. It allows
you to install your monitor in a Plug and Play compatible
system without the usual hassles and confusion. Your PC
system can easily identify and configure itself for use with
your display. This monitor automatically tells the PC system
its Extended Display Identification Data (EDID) using Display
Data Channel (DDC) protocols.
Preset Signals
Source
AV1 ~ AV5
(RF)
Component 1
Component 2
Video
PAL
SECAM
NTSC4.43
NTSC3.58
480/60i
576/50i
480/60p
576/50p
720/60p
1080/50i
1080/60i
Vertical frequency
(Hz)
50
50
60
60
60
50
60
50
60
50
60
Horizontal frequency
(kHz)
15.625
15.625
15.734
15.734
15.734
15.625
31.469
31.250
45.000
28.125
33.750
Resolution
(Lines)
575
575
483
483
483
575
483
575
720
1080
1080
51
Setting up Your PC Software (Windows only)
ENG
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card.
On the windows screen, select in the following
sequence: Start ➞ Settings ➞ Control Panel.
When the control panel screen appears, click on
Display and a display dialog-box will appear.
Select the Settings tab in the display dialog-box.
The two key variables that apply the Media StationPC interface are “Resolution” and “Colors”.
The correct settings for these two variables are:
◆ Size (sometimes called “Resolution”)
1024 x 768 pixels.
◆ Color
24-bit color (might also be expressed as “16
million colors”)
Shown at left is a typical screen for “Display”
dialog box.
If a vertical-frequency option exists on your display
settings dialog box, the correct value is 60Hz.
Otherwise, just click OK and exit the dialog box.
52
Input Mode (PC/DVI)
ENG
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Standard
Dot x Line
VGA
640 x 480
SVGA
720 x 400
800 x 600
XGA
1024 x 768
WXGA
848 x 480
Vertical
frequency (Hz)
Horizontal
frequency (kHz)
Vertical
polarity
Horizontal
polarity
85.0
75.0
72.8
59.9
70.1
85.1
75.0
72.2
60.3
56.3
85.0
75.0
70.1
60.0
85
75
72
70
60
43.3
37.5
37.9
31.5
31.5
53.7
46.9
48.1
37.9
35.2
68.7
60.0
56.5
48.3
42.9
37.5
36.1
35.0
29.8
N
N
N
N
P
P
P
P
P
P
P
P
N
N
P
P
P
P
P
N
N
N
N
N
P
P
P
P
P
P
P
N
N
N
N
N
N
N
(N: Negative / P: Positive)
◆
◆
◆
◆
The interlace mode is not supported.
The PDP might operate abnormally if a non-standard video format is selected.
The 4:3 mode does not work with input signals from “720 x 400”.
The DVI mode does not support “1024 x 768” (85Hz).
Notes
◆ The text quality of PC screen is optimum in the VGA mode (640 x 480), the full size displayed PC mode
is optimum in the SVGA mode (800 x 600).
◆ When this PDP is used as a PC display, 24-bit color is supported (over 16 million colors).
◆ Your PC display screen might appear different depending on the manufacturer (and your particular version of
Windows). Check your PC instruction book for information about connecting your PC to a PDP.
◆ If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHz (horizontal).
In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned
off (or if the PC is disconnected). If so, press the Source button to enter the Video mode. Also, make sure that
the PC is connected.
◆ When connecting a notebook PC to the PDP, make sure that the PC screen is displayed through only the
PDP monitor (Otherwise, random signals might appear).
◆ When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable
connections.
53
Pin Configurations
ENG
PC Input Connector
(15Pin)
1
6
11
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
3
2
4
8
7
12
13
14
PC IN
Red (R)
Green (G)
Blue (B)
Grounding
Grounding (DDC)
Red (R) Grounding
Green (G) Grounding
Blue (B) Grounding
Reserved
Sync Grounding
Grounding
Data (DDC)
Horizontal sync.
Vertical sync.
Clock (DDC)
54
5
10
DVI Input Connector
(24Pin)
15
1
2
9
10 11 12 13 14 15 16
3
4
5
6
7
8
17 18 19 20 21 22 23 24
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
Clock (DDC)
Data (DDC)
Not Connected
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3T.M.D.S. Data3+
+5V Power
5V Grounding
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
Care and Maintenance
ENG
With proper care, your PDP will give you many years of service. Please follow these guidelines to get
the maximum performance from your PDP.
◆ Identifying Problems
- Do not put the PDP near extremely hot, cold, humid or dusty places.
- Do not put the PDP near appliances that create magnetic fields.
- Keep the ventilation openings clear.
- Do not place the PDP on a rough and slanted surface, such as cloth or paper.
◆ Liquids
- Do not handle liquids near or on the PDP.
◆ Cabinet
- Never open the cabinet or touch the parts inside.
- Wipe your PDP with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals.
- Do not put heavy objects on top of the cabinet.
◆ Temperature
- If your PDP is suddenly moved from a cold to a warm place, unplug the power cord for at least two
hours so that moisture that may have formed inside the unit can dry completely.
Troubleshooting
Before contacting Service Personnel, perform the following simple checks. If you cannot solve the
problem using the instructions below, note the model and serial number of the PDP and contact your
local dealer.
No sound or picture
◆
◆
◆
◆
Normal picture but no sound
◆ Check the volume.
◆ Check whether the Mute button has been pressed.
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the Media
Station, then move it further away.
◆ Plug your television into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
The power indicator is amber blinking.
◆ The monitor is using its power management system.
Check the power management utility on your computer.
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the Power button.
Check the picture contrast and brightness settings.
Check the volume.
55
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
ELECTRONICS
BN68-00382A-02 (ENG)