Samsung RNX-EASYN4 User's Manual

Wireless Router RNX-EasyN4
User Manual
TABLE OF CONTENTS
1
INTRODUCTION .............................................................................................................. 3
2
KEY FEATURES .............................................................................................................. 4
3
PACKAGE CONTENTS................................................................................................... 5
4
PRODUCT LAYOUT ........................................................................................................ 6
5
NETWORK + SYSTEM REQUIREMENTS...................................................................... 9
6
RNX-EASYN4 PLACEMENT........................................................................................... 9
7
SETUP LAN, WAN......................................................................................................... 10
8
PC NETWORK ADAPTER SETUP (WINDOWS XP) .....................................................11
9
BRING UP RNX-EASYN4.............................................................................................. 13
10
SMART WIZARD ........................................................................................................... 13
11
INITIAL SETUP RNX-EASYN4...................................................................................... 24
12
AP ROUTER MODE ...................................................................................................... 26
13
REPEATER MODE ........................................................................................................ 90
APPENDIX A – FCC INTERFERENCE STATEMENT ......................................................... 109
APPENDIX B – IC INTERFERENCE STATEMENT..............................................................110
Introduction
Congratulations on your purchase of RNX-EASYN4 Wireless Network
Broadband Router. RNX-EASYN4 is compliant with draft 802.11n v2.0 up to 6
times faster than standard 802.11g based routers while still being compatible
with 802.11g & 802.11b gadgets. RNX-EASYN4 is not only a Wireless Access
Point, but also doubles as a 4-port full-duplex Switch that connects your wiredEthernet devices together at incredible speeds.
At 300 Mbps wireless transmission rate, Access Point built into the Router
uses advanced MIMO (Multi-Input, Multi-Output) technology to transmit multiple
steams of data in a single wireless channel giving you seamless access to
multimedia content. Robust RF signal travels farther, eliminates dead spots and
extends network range. For data protection and privacy, RNX-EASYN4 encodes
all wireless transmissions with WEP, WPA, and WPA2 encryption.
With inbuilt DHCP Server & powerful SPI firewall RNX-EASYN4 protects your
computers against intruders and most known Internet attacks but provides safe
VPN pass-through. With incredible speed and QoS function of 802.11n, (draft2.0)
RNX-EASYN4 is ideal for media-centric applications like streaming video,
gaming, and VoIP telephony to run multiple media-intense data streams through
the network at the same time, with no degradation in performance.
Wireless Router RNX-EasyN4
User Manual
1 Key Features
Features
Advantages
Incredible Data Rate up to 300Mbps**
Heavy data payloads such as MPEG
video streaming
IEEE 802.11n Compliant and
Fully Interoperable with IEEE
backward compatible with 802.11b/g
802.11b / IEEE 802.11g compliant
devices with legacy protection
Four 10/100 Mbps Fast Switch Ports
Scalability, extend your network.
(Auto-Crossover)
Firewall supports, DMZ, MAC Filter, IP
Avoids the attacks of Hackers or
Filter, URL Filter, ICMP Blocking, SPI,
Viruses from Internet
Port Mapping, Port Forwarding, Port
Trigger
Support 802.1x Authenticator, 802.11i
Provide mutual authentication
(WPA/WPA2, AES), VPN pass-through
(Client and dynamic encryption keys
to enhance security
WDS (Wireless Distribution System)
Make wireless AP and Bridge mode
simultaneously as a wireless
repeater
** Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual
throughput may vary. Network conditions and environmental factors lower actual throughput rate. All
specifications are subject to change without notice.
Wireless Router RNX-EasyN4
User Manual
2 Package Contents
Open the package carefully, and make sure that none of the items listed below are
missing. Do not discard the packing materials, in case of return; the unit must be
shipped back in its original package.
1. 802.11n SOHO Router
2. 100V~120V Power Adapter
3. 2dBi 2.4GHz Fixed Antennas
4. Quick Install Guide
5. CD (User’s Manual)
Wireless Router RNX-EasyN4
3 Product Layout
User Manual
Wireless Router RNX-EasyN4
User Manual
LED
Description
POWER
Lights up when powered ON. Blinks on
TEST/RESET
WLAN
Lights up in ORANGE when WLAN is
enabled. Blinks on traffic
LAN PORT ACTIVY
Blinks on traffic for specific LAN PORT
100 Mbps
Lights up when 100 Mbps data rate
enabled on that specific port
ITEM
Description
Reset
Click this button to restart the system, or
Press this button and hold for 10 seconds
to restart the system.
Wireless Router RNX-EasyN4
User Manual
WPS
Click this button to start WPS function.
DC IN
Power connector, connects to DC 12V
Power Adapter
LAN1 ~ 4
Local Area Network (LAN) ports 1 to 4
INTERNET
Wide Area Network(WAN) port
Wireless Router RNX-EasyN4
User Manual
4 Network + System Requirements
To begin using the RNX-EASYN4, make sure you meet the following as minimum
requirements:
h
PC/Notebook.
h
Operating System – Microsoft Windows 98SE/ME/XP/2000/VISTA
h
1 Free Ethernet port.
h
WiFi card/USB dongle (802.11b/g/n) – optional.
h
External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45).
h
PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera etc.)
h
Few Ethernet compatible CAT5 cables.
5 RNX-EASYN4 Placement
You can place RNX-EASYN4 on a desk or other flat surface, or you can mount it on
a wall. For optimal performance, place your Wireless Broadband Router in the center
of your office (or your home) in a location that is away from any potential source of
interference, such as a metal wall or microwave oven. This location must be close to
a power connection and your ADSL/Cable modem. If the antennas are not positioned
correctly, performance loss can occur.
Wireless Router RNX-EasyN4
User Manual
6 Setup LAN, WAN
LAN connection:
Connect Ethernet cable between your PC/Notebook LAN port &
one of the 4 available LAN ports on RNX-EASYN4.
WAN connection:
Connect Ethernet cable between WAN ports of your ADSL/CABLE
modem & INTERNET port of RNX-EASYN4. Make sure your
ADSL/CABLE modem is working well. Contact your ISP if you
have any questions.
Wireless Router RNX-EasyN4
User Manual
7 PC Network Adapter setup (Windows XP)
•
Enter [Start Menu] Æ select [Control panel] Æ select [Network].
•
Select [Local Area Connection]) icon=>select [properties]
Wireless Router RNX-EasyN4
•
Select [Internet Protocol (TCP/IP)] =>Click [Properties].
•
Select the [General] tab.
User Manual
RNX-EASYN4 supports [DHCP] function, please select both [Obtain an IP
address automatically] and [Obtain DNS server address automatically].
Wireless Router RNX-EasyN4
User Manual
8 Bring up RNX-EASYN4
Connect the supplied power-adapter to the power inlet port and connect it
to a wall outlet. Then, RNX-EASYN4 automatically enters the self-test phase.
During self-test phase, Power LED will blink briefly, and then will be lit
continuously to indicate that this product is in normal operation.
9 Smart Wizard
CHECK
•
Internet connection should be setup & ready to use (ADSL or cable modem).
•
Modem must provide RJ45 port to connect with RNX-EASYN4.
•
Microsoft Windows compatible PC/Notebook with UPnP enabled network adapter
•
CAT 5 network cable(s), RJ45 port on PC/Notebook.
STEP 1
Connect RNX-EASYN4 WAN port & your modem WAN port with RJ45 cable.
STEP 2
Power up RNX-EASYN4.POWER led on front panel lights up & remains stable.
STEP 3
Connect RNX-EASYN4 LAN port & PC/Notebook RJ45 port with network cable.
Click on this icon to run SMART WIZARD.
Wireless Router RNX-EasyN4
User Manual
Click Setup Wizard to setup your RNX-EASYN4 router.
Click User Manual to launch smart wizard user manual.
Click Adobe Reader to setup Adobe Acrobat reader on your PC/Notebook. Click
EXIT anytime you want to abort.
Wireless Router RNX-EasyN4
Click <Next> to proceed. Click <Exit> to abort.
User Manual
Wireless Router RNX-EasyN4
User Manual
RNX-EASYN4 should be setup as depicted above.
Make sure your DSL/CABLE modem is setup and working. Else take the help of
your internet service provider.
Click <Next> to proceed.
Wireless Router RNX-EasyN4
User Manual
Check the MODEM and RNX-EASYN4 connection. It should be as shown below.
Check power connection for modem as well as RNX-EASYN4.
Make sure antenna is connected to rear panel of RNX-EASYN4.
Click <Next> to proceed.
Wireless Router RNX-EasyN4
User Manual
Notice the LED that should be light up at this stage. If not, check your procedures
again.
Click <Next> to configure WAN & Wireless settings.
Wireless Router RNX-EasyN4
User Manual
User name and password are admin/admin. Click <OK>. Your default browser
will connect to RNX-EASYN4 Web Server http://192.168.0.1 .
Wireless Router RNX-EasyN4
User Manual
Click <Next> to enter mode selection.
Select the mode that RNX-EASYN4 is going to be and set its configurations. AP Router
mode does not enable WAN interface, Setup Wizard will skip WAN Configuration.
Wireless Router RNX-EasyN4
User Manual
Click <Next> to automatically detect your Internet Network settings.
You could choose your service type or select Others to setup WAN configurations
manually.
Smart Wizard has detected DHCP client. Configure the host name and MAC
address of your ADSL modem. Click Next to proceed.
Wireless Router RNX-EasyN4
User Manual
Smart Wizard has finished setting up WAN Configuration. Click <Next> to
proceed.
Enter the name for your wireless network (SSID) and security key
Click <Next> to proceed
Wireless Router RNX-EasyN4
User Manual
To apply the entire configuration, click <Reboot>.
NOTE:
After Wireless settings are applied, you need to connect from your WLAN
client with the security settings you just finished configuring. Remember
the type of security & security key.
Wireless Router RNX-EasyN4
User Manual
10 Initial Setup RNX-EASYN4
RNX-EASYN4 uses web-interface for configuration to be accessed through your
web browser, such as Internet Explorer or Netscape Communicator.
- LOGIN Procedure
1. OPEN your browser (e.g. Internet Explorer).
2. Type http://192.168.0.1 in address bar and hit [Enter] button on your keyboard.
Wireless Router RNX-EasyN4
3. Click <OK> to navigate into RNX-EASYN4 configuration home page.
4. You will see the home page of RNX-EASYN4 as follows.
User Manual
Wireless Router RNX-EasyN4
User Manual
12 AP Router Mode
„ System
- Status
This page allows you to monitor the current status of your router. You can use the
status page to quickly see if you have any updated firmware available (bug fixes,
updates). You can navigate from this page with a few interesting options for reminding or
skipping this page forever & so forth.
Once you click on <OK> button to go to the requested page, you can see the status
page of the RNX-EASYN4.
System: You can see the UP time, hardware information, serial number as well as
firmware version information.
Wireless Router RNX-EasyN4
User Manual
WAN Settings: This section displays whether the WAN port is connected to a
Cable/DSL connection. It also displays the router’s WAN IP
address, Subnet Mask, and ISP Gateway as well as MAC
address, the Primary DNS.
LAN Settings: This section displays the Broadband router LAN port’s current LAN
& WLAN information. It also shows whether the DHCP Server
function is enabled / disabled.
Wireless Router RNX-EasyN4
User Manual
WLAN Settings: This section displays the current WLAN configuration settings
you’ve configured in the Wizard / Basic Settings / Wireless
Settings section. Wireless configuration details such as SSID,
Security settings, BSSID, Channel number, mode of operation
are briefly shown.
Wireless Router RNX-EasyN4
User Manual
- LAN
The LAN Tabs reveals LAN settings which can be altered at will. If you are an
entry level user, try accessing a website from your browser. If you can access
website without a glitch, just do not change any of these settings.
Click <Apply> at the bottom of this screen to save the changed configurations.
Wireless Router RNX-EasyN4
User Manual
LAN IP
IP address: 192.168.0.1. It is the router’s LAN IP address (Your LAN clients default
gateway IP address). It can be changed based on your own choice.
IP Subnet Mask: 255.255.255.0 Specify a Subnet Mask for your LAN segment.
802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree function
is enabled, this router will use the spanning tree protocol to
prevent network loops.
DHCP Server
DHCP Server: This will enable or disable the Dynamic Pool setting..
Lease time: This is the lease time of each assigned IP address.
Wireless Router RNX-EasyN4
User Manual
Start IP: This will be the beginning of the pool of IP addresses available for client
devices.
End IP: This will be the end of the pool of IP addresses available for client devices.
Domain name: The Domain Name for the existing or customized network.
- DHCP
View the current LAN clients which are assigned with an IP Address by the DHCPserver. This page shows all DHCP clients (LAN PCs) currently connected to your
network. The table shows the assigned IP address, MAC address and expiration time
for each DHCP leased client. Use the <Refresh> button to update the available
information. Hit <Refresh> to get the updated table.
You can check “Enable Static DHCP IP“. It is possible to add more static DHCP
IPs. They are listed in the table “Current Static DHCP Table“. IP address can be
deleted at will from the table.
Click <Apply> button to save the changed configuration.
Wireless Router RNX-EasyN4
User Manual
- Schedule
This page allows user to set up schedule function for Firewall and Power Saving
.
Wireless Router RNX-EasyN4
User Manual
Add schedule, edit schedule options to allow configuration of firewall and power
savings services. Fill in the schedule and select type of service. Click <Apply> to
implement those settings.
Wireless Router RNX-EasyN4
User Manual
The schedule table lists the pre-schedule service-runs. You can select any of them
using the check box.
- Event Log
View operation event log. This page shows the current system log of the
Broadband router. It displays any event occurred after system start up. At the bottom
of the page, the system log can be saved <Save> to a local file for further processing
or the system log can be cleared <Clear> or it can be refreshed <Refresh> to get
the most updated information. When the system is powered down, the system log
will disappear if not saved to a local file.
Wireless Router RNX-EasyN4
User Manual
- Monitor
Show histogram for network connection on WAN, LAN & WLAN. Auto refresh
keeps information updated frequently.
Wireless Router RNX-EasyN4
User Manual
- Language
This Wireless Router support multiple language of web pages, You could select
your native language here.
Wireless Router RNX-EasyN4
User Manual
„ Wizard
Click Wizard to configure the Broadband Router. Setup wizard will now be displayed;
check that the modem is connected and click <Next>. The details please refer to
Smart Wizard.
Wireless Router RNX-EasyN4
User Manual
„ INTERNET
- Status
This page shows the current Internet connection type and status
- Dynamic IP
Use the MAC address when registering for Internet service, and do not change it
unless required by your ISP. If your ISP used the MAC address of the Ethernet card as
an identifier, connect only the PC with the registered MAC address to the broadband
router and click the <Clone MAC Address> button. This will replace the current MAC
address with the already registered Ethernet card MAC address
Wireless Router RNX-EasyN4
User Manual
Host Name: This is optional.
MAC address: The default value is set to the WAN’s physical interface of the
broadband router.
- Static IP
If your ISP Provider has assigned a fixed IP address, enter the assigned IP address,
Subnet mask, Default Gateway IP address, and Primary DNS of your ISP provider.
Wireless Router RNX-EasyN4
- Point-to-Point over Ethernet Protocol (PPPoE)
User Manual
Wireless Router RNX-EasyN4
User Manual
Login / Password: Enter the PPPoE username and password assigned by your ISP
Provider.
Service Name: This is normally optional.
Maximum Transmission Unit (MTU): This is the maximum size of the packets.
Type: Enable the Auto-reconnect option to automatically re-establish the connection
when an application attempts to access the Internet again.
Idle Timeout: This is a maximum period of time for which the Internet connection is
maintained during inactivity. If the connection is inactive for longer than the
Maximum Idle Time, it will be dropped.
- Point-to-Point Tunneling Protocol (PPTP)
PPTP allows the secure connection over the Internet by simply dialing in a local
point provided by your ISP provider. The following screen allows client PCs to establish
a normal PPTP session and provides hassle-free configuration of the PPTP client on
each client PC.
Click <Apply> to save configuration and connect to ISP provider.
Wireless Router RNX-EasyN4
User Manual
„ Wireless Settings
- Basic
In basic setting page, you can set wireless Radio, Mode, Band, SSID, and
Channel.
Radio: You can turn on/off wireless radio. If wireless Radio is off, you cannot
associate with AP through wireless.
Mode: In this device, we support three operation modes which are AP router and
AP route with WDS (we will introduce this function later section). If you
choose AP Router Mode, you can select AP or WDS function in the dropdown menu.
Band: You can select the wireless standards running on your network environment.
Wireless Router RNX-EasyN4
User Manual
2.4 GHz(B): If all your clients are 802.11b, select this one.
2.4 GHz(N): If all your clients are 802.11n, select this one.
2.4 GHz(B+G): Either an 802.11b or an 802.11g wireless devices are in
your environment.
2.4 GHz(G): If all your clients are 802.11g, select this one.
2.4 GHz(B+G+N): Either 802.11b, 802.11g, or 802.11n wireless devices
are in your environment.
Enable ESSID: We support 4 multiple SSIDs in this device. Please select how
many SSIDs you would like to use in your network environment.
ESSID1~4: ESSID is the name of your wireless network. It might be a unique
name to identify this wireless device in the Wireless LAN. It is case
sensitive and up to 32 printable characters. You might change the
default ESSID for added security.
Auto Channel: Device will search all valid channels, then decide a most clean
channel and change to this channel if you enable this function.
Depend on this function enable or not, you will see different item
below Auto Channel.
Channel: If Auto Channel is disabled, you should choose a static channel and AP
will use this channel to communicate with other clients.
Check Channel Time: If Auto Channel is enabled, you can choose a period from
the drop-down menu. AP will change to a clean channel
periodically.
Wireless Router RNX-EasyN4
User Manual
- WDS with AP Router
Wireless Distribution System, a system that enables the wireless interconnection
of access point, allows a wireless network to be expended using multiple access
points without a wired backbone to like them. Each WDS APs need setting as same
channel and encryption type.
MAC address 1~4: Please enter the MAC address of the neighboring APs that
participates in WDS, we support 4 devices now.
Set Security: WDS Security depends on your AP security settings. Note: it does
not support mixed mode such as WPA-PSK/WPA2-PSK Mixed
mode.
Wireless Router RNX-EasyN4
User Manual
- Advanced
This tab allows you to set the advanced wireless options. The options included are
Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, and
Preamble Type. You should not change these parameters unless you know what
effect the changes will have on the router.
Fragment Threshold: This specifies the maximum size of a packet during the
fragmentation of data to be transmitted. If you set this value
too low, it will result in bad performance.
RTS Threshold: When the packet size is smaller than the RTS threshold, the
wireless router will not use the RTS/CTS mechanism to send this
packet.
Wireless Router RNX-EasyN4
User Manual
Beacon Interval: is the interval of time that this wireless router broadcasts a
beacon. A Beacon is used to synchronize the wireless network.
DTIM Period: Enter a value between 1 and 255 for the Delivery Traffic Indication
Message (DTIM). A DTIM is a countdown informing clients of the next
window for listening to broadcast and multicast messages
Data Rate: The “Data Rate” is the rate that this access point uses to transmit data
packets. The access point will use the highest possible selected
transmission rate to transmit the data packets.
N Data Rate: The “Data Rate” is the rate that this access point uses to transmit data
packets for N compliant wireless nodes. Highest to lowest data rate
can be fixed.
Channel Bandwidth: This is the range of frequencies that will be used.
Preamble Type: The “Long Preamble” can provide better wireless LAN compatibility
while the “Short Preamble” can provide better wireless LAN
performance.
CTS Protection: It is recommended to enable the protection mechanism. This
mechanism can decrease the rate of data collision between
802.11b and 802.11g wireless stations. When the protection mode
is enabled, the throughput of the AP will be a little lower due to a
lot of frame-network that is transmitted.
TX Power: This can be set to a bare minimum or maximum power.
Wireless Router RNX-EasyN4
User Manual
- Security
This Access Point provides complete wireless LAN security functions, included
are WEP, IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-shared key and WPA
with RADIUS. With these security functions, you can prevent your wireless LAN from
illegal access. Please make sure your wireless stations use the same security
function, and are setup with the same security key.
ESSID Selection: This broadband router support multiple ESSID, you could
select and set up the wanted ESSID.
Broadcast ESSID: If you enabled “Broadcast ESSID”, every wireless station
located within the coverage of this access point can discover
this access point easily. If you are building a public wireless
network, enabling this feature is recommended. Disabling
“Broadcast ESSID” can provide better security.
Wireless Router RNX-EasyN4
User Manual
WMM: Wi-Fi MultiMedia if enabled supports QoS for experiencing better audio,
video and voice in applications.
Encryption: When you choose to disable encryption, it is very insecure to
operate RNX-EASYN4.
Enable 802.1x Authentication
IEEE 802.1x is an authentication protocol. Every user must use a valid account to
login to this Access Point before accessing the wireless LAN. The authentication is
processed by a RADIUS server. This mode only authenticates users by IEEE 802.1x,
but it does not encrypt the data during communication.
WEP Encryption
When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to
encrypt data. You can generate the key by yourself and enter it. You can enter four
WEP keys and select one of them as a default key. Then the router can receive any
packets encrypted by one of the four keys.
Wireless Router RNX-EasyN4
User Manual
Authentication Type: There are two authentication types: "Open System" and
"Shared Key". When you select "Open System", wireless
stations can associate with this wireless router without WEP
encryption. When you select "Shared Key", you should also
setup a WEP key in the "Encryption" page. After this has
been done, make sure the wireless clients that you want to
connect to the device are also setup with the same
encryption key.
Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit.
The larger the key will be the higher level of security is used, but the
throughput will be lower.
Key Type: You may select ASCII Characters (alphanumeric format) or Hexadecimal
Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.
Key1 - Key4: The WEP keys are used to encrypt data transmitted in the wireless
network. Use the following rules to setup a WEP key on the device.
Wireless Router RNX-EasyN4
User Manual
64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or
5-digit ASCII character as the encryption keys.
128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9" range) or
13-digit ASCII characters as the encryption keys.
Click <Apply> at the bottom of the screen to save the above configurations. You
can now configure other sections by choosing Continue, or choose Apply to apply
the settings and reboot the device.
WPA Pre-Shared Key Encryption
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a
pre-shared key to authenticate wireless stations and encrypt data during
communication. It uses TKIP or CCMP (AES) to change the encryption key
frequently. So the encryption key is not easy to be cracked by hackers. This is the
best security available.
Wireless Router RNX-EasyN4
User Manual
WPA-Radius Encryption
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an
external RADIUS server to authenticate wireless stations and provide the session
key to encrypt data during communication.
It uses TKIP or CCMP (AES) to change the encryption key frequently. Press
<Apply> button when you are done.
Wireless Router RNX-EasyN4
User Manual
- MAC Address Filtering
This wireless router supports MAC Address Control, which prevents unauthorized
clients from accessing your wireless network.
Enable wireless access control: Enable the wireless access control function
Wireless Router RNX-EasyN4
User Manual
Adding an address into the list
Enter the "MAC Address" and "Comment" of the wireless station to be added
and then click <Add>. The wireless station will now be added into the "Current
Access Control List" below. If you are having any difficulties filling in the fields,
just click "Clear" and both "MAC Address" and "Comment" fields will be cleared.
Remove an address from the list
If you want to remove a MAC address from the "Current Access Control List
", select the MAC address that you want to remove in the list and then click
"Delete Selected". If you want to remove all the MAC addresses from the list,
just click the <Delete All> button. Click <Reset> will clear your current
selections.
Click <Apply> at the bottom of the screen to save the above configurations.
- Wi-Fi Protected Setup (WPS)
WPS is the simplest way to establish a connection between the wireless clients
and the wireless router. You don’t have to select the encryption mode and fill in a
long encryption passphrase every time when you try to setup a wireless connection.
You only need to press a button on both wireless client and wireless router, and the
WPS will do the rest for you.
The wireless router supports two types of WPS: WPS via Push Button and WPS
via PIN code. If you want to use the Push Button, you have to push a specific button
on the wireless client or in the utility of the wireless client to start the WPS mode, and
switch the wireless router to WPS mode. You can simply push the WPS button of the
wireless router, or click the ‘Start to Process’ button in the web configuration
interface. If you want to use the PIN code, you have to know the PIN code of the
wireless client and switch it to WPS mode, then fill-in the PIN code of the wireless
client through the web configuration interface of the wireless router.
Wireless Router RNX-EasyN4
User Manual
WPS: Check the box to enable WPS function and uncheck it to disable the WPS
function.
WPS Current Status: If the wireless security (encryption) function of this wireless
router is properly set, you’ll see a ‘Configured’ message
here. Otherwise, you’ll see ‘UnConfigured’.
Self Pin Code: This is the WPS PIN code of the wireless router. You may need this
information when connecting to other WPS-enabled wireless
devices.
SSID: This is the network broadcast name (SSID) of the router.
Wireless Router RNX-EasyN4
User Manual
Authentication Mode: It shows the active authentication mode for the wireless
connection.
Passphrase Key: It shows the passphrase key that is randomly generated by the
wireless router during the WPS process. You may need this
information when using a device which doesn’t support WPS.
Interface: If device is set to repeater mode, you can choose “Client” interface to
connect with other AP by using WPS, otherwise you may choose “AP”
interface to do WPS with other clients.
WPS via Push Button: Press the button to start the WPS process. The router will
wait for the WPS request from the wireless devices within 2
minutes.
WPS via PIN: You can fill-in the PIN code of the wireless device and press the
button to start the WPS process. The router will wait for the WPS
request from the wireless device within 2 minutes.
- Client List
This WLAN Client Table shows the Wireless client associate to this Wireless
Router.
Wireless Router RNX-EasyN4
User Manual
- Policy
The Broadband router can allow you to set up the Wireless Access Policy.
WAN Connection: Allow Wireless Client on specific SSID to access WAN port.
Communication between Wireless clients: Allow Wireless Client to communicate
with other Wireless Client on specific SSID.
Communication between Wireless clients and wired clients: Allow Wireless Client
to communicate with other Wireless Client on specific SSID and Wired Client on the
switch. Or Wireless Client will allow to access WAN port only
Wireless Router RNX-EasyN4
User Manual
„ Firewall Settings
The Broadband router provides extensive firewall protection by restricting connection
parameters, thus limiting the risk of hacker attacks, and defending against a wide array
of common Internet attacks. However, for applications that require unrestricted access to
the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ).
Wireless Router RNX-EasyN4
User Manual
Note: To enable the Firewall settings select Enable and click Apply
- Advanced
You can allow the VPN packets to pass through this Broadband router.
Wireless Router RNX-EasyN4
User Manual
- Demilitarized Zone (DMZ)
If you have a client PC that cannot run an Internet application (e.g. Games)
properly from behind the NAT firewall, then you can open up the firewall restrictions
to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function
allows you to re-direct all packets going to your WAN port IP address to a particular
IP address in your LAN. The difference between the virtual server and the DMZ
function is that the virtual server re-directs a particular service/Internet application
(e.g. FTP, websites) to a particular LAN client/server, whereas DMZ re-directs all
packets (regardless of services) going to your WAN IP address to a particular LAN
client/server.
Wireless Router RNX-EasyN4
User Manual
Enable DMZ: Enable/disable DMZ
LAN IP Address: Fill-in the IP address of a particular host in your LAN Network that
will receive all the packets originally going to the WAN port/Public
IP address above.
Click <Apply> at the bottom of the screen to save the above configurations.
- Denial of Service (DoS)
The Broadband router's firewall can block common hacker attacks, including
Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur
the router can log the events.
Wireless Router RNX-EasyN4
User Manual
Ping of Death: Protections from Ping of Death attack.
Discard Ping From WAN: The router’s WAN port will not respond to any Ping
requests
Port Scan: Protects the router from Port Scans.
Sync Flood: Protects the router from Sync Flood attack.
- MAC Filter
Wireless Router RNX-EasyN4
User Manual
If you want to restrict users from accessing certain Internet applications / services
(e.g. Internet websites, email, FTP etc.), and then this is the place to set that
configuration. Access Control allows users to define the traffic type permitted in your
LAN. You can control which PC client can have access to these services.
Enable MAC Filtering: Check to enable or disable MAC Filtering.
Deny: If you select “Deny” then all clients will be allowed to access Internet accept
for the clients in the list below.
Allow: If you select “Allow” then all clients will be denied to access Internet accept
for the PCs in the list below.
Wireless Router RNX-EasyN4
User Manual
Add PC MAC Address
Fill in “LAN MAC Address” and <Description> of the PC that is allowed to
access the Internet, and then click <Add>. If you find any typo before adding it
and want to retype again, just click <Reset> and the fields will be cleared.
Remove PC MAC Address
If you want to remove some PC from the "MAC Filtering Table", select the
PC you want to remove in the table and then click <Delete Selected>. If you
want to remove all PCs from the table, just click the <Delete All> button. If you
want to clear the selection and re-select again, just click <Reset>.
Click <Apply> at the bottom of the screen to save the above configurations.
Wireless Router RNX-EasyN4
User Manual
- IP Filter
Enable IP Filtering: Check to enable or disable IP Filtering.
Deny: If you select “Deny” then all clients will be allowed to access Internet accept
for the clients in the list below.
Allow: If you select “Allow” then all clients will be denied to access Internet accept
for the PCs in the list below.
Add PC IP Address
You can click <Add> PC to add an access control rule for users by an IP address or
IP address range.
Remove PC IP Address
If you want to remove some PC IP from the <IP Filtering Table>,
select the PC you want to remove in the table and then click <Delete Selected>. If you
want to remove all PCs from the table, just click the <Delete All> button.
Wireless Router RNX-EasyN4
User Manual
Click <Apply> at the bottom of the screen to save the above configurations.
- URL Filter
You can block access to some Web sites from particular PCs by entering a full
URL address or just keywords of the Web site.
Enable URL Blocking: Enable or disable URL Blocking
Add URL Keyword
Fill in “URL/Keyword” and then click <Add>. You can enter the full URL address or the
keyword of the web site you want to block. If you happen to make a mistake and want to
retype again, just click "Reset" and the field will be cleared.
Wireless Router RNX-EasyN4
User Manual
Remove URL Keyword
If you want to remove some URL keywords from the "Current URL Blocking Table",
select the URL keyword you want to remove in the table and then click <Delete
Selected>.
If you want remove all URL keywords from the table, click <Delete All> button. If you
want to clear the selection and re-select again, just click <Reset>.
Click <Apply> at the bottom of the screen to save the above configurations
Wireless Router RNX-EasyN4
User Manual
„ Advanced Settings
- Network Address Translation (NAT)
Network Address Translation (NAT) allows multiple users at your local site to
access the Internet through a single Public IP Address or multiple Public IP
Addresses. NAT provides Firewall protection from hacker attacks and has the
flexibility to allow you to map Private IP Addresses to Public IP Addresses for key
services such as Websites and FTP. Select Disable to disable the NAT function.
Wireless Router RNX-EasyN4
User Manual
- Port Mapping
Port Mapping allows you to re-direct a particular range of service port numbers
(from the Internet / WAN Port) to a particular LAN IP address. It helps you to host
servers behind the router NAT firewall.
Enable Port Mapping: Enable or disable port mapping function.
Description: description of this setting.
Local IP: This is the local IP of the server behind the NAT firewall.
Type: This is the protocol type to be forwarded. You can choose to forward “TCP” or
“UDP” packets only, or select “BOTH” to forward both “TCP” and “UDP”
packets.
Port Range: The range of ports to be forward to the private IP.
Wireless Router RNX-EasyN4
User Manual
Add Port Mapping
Fill in the "Local IP", “Type”, “Port Range” and "Description" of the setting to be
added and then click "Add". Then this Port Mapping setting will be added into the
"Current Port Mapping Table" below. If you find any typo before adding it and want to
retype again, just click <Clear> and the fields will be cleared.
Remove Port Mapping
If you want to remove a Port Mapping setting from the "Current Port Mapping Table",
select the Port Mapping setting that you want to remove in the table and then click
D<Delete Selected>. If you want to remove all Port Mapping settings from the table,
click <Delete All> button. Click <Reset> will clear your current selections.
Click <Apply> at the bottom of the screen to save the above configurations.
- Port Forwarding (Virtual Server)
Use the Port Forwarding (Virtual Server) function when you want different
servers/clients in your LAN to handle different service/Internet application type (e.g.
Email, FTP, Web server etc.) from the Internet. Computers use numbers called port
numbers to recognize a particular service/Internet application type. The Virtual Server
allows you to re-direct a particular service port number (from the Internet/WAN Port) to a
particular LAN private IP address and its service port number. (See Glossary for an
explanation on Port number).
Wireless Router RNX-EasyN4
User Manual
Wireless Router RNX-EasyN4
User Manual
Enable Port Forwarding: Enable or disable Port Forwarding.
Description: The description of this setting.
Local IP / Local Port: This is the LAN Client/Host IP address and Port number that
the Public Port number packet will be sent to.
Type: Select the port number protocol type (TCP, UDP or both). If you are unsure,
then leave it to the default “both” setting. Public Port enters the service
(service/Internet application) port number from the Internet that will be redirected to the above Private IP address host in your LAN Network.
Public Port: Port number will be changed to Local Port when the packet enters your
LAN Network.
Add Port Forwarding
Fill in the "Description" , "Local IP", "Local Port", "Type" and “Public Port”
of the setting to be added and then click <Add> button. Then this Virtual
Server setting will be added into the "Current Port Forwarding Table" below.
If you find any typo before adding it and want to retype again, just click <Clear>
and the fields will be cleared.
Remove Port Forwarding
If you want to remove Port Forwarding settings from the "Current Port
Forwarding Table", select the Port Forwarding settings you want to remove in
the table and then click "Delete Selected". If you want to remove all Port
Forwarding settings from the table, just click the <Delete All> button. Click
<Reset> will clear your current selections.
Click <Apply> at the bottom of the screen to save the above configurations.
Wireless Router RNX-EasyN4
User Manual
- Port Triggering (Special Applications)
Some applications require multiple connections, such as Internet games, video
Conferencing, Internet telephony and others. In this section you can configure the
router to support multiple connections for these types of applications.
Enable Trigger Port: Enable or disable the Port Trigger function.
Trigger Port: This is the outgoing (Outbound) range of port numbers for this
particular application.
Trigger Type: Select whether the outbound port protocol is “TCP”, “UDP” or “BOTH”.
Public Port: Enter the In-coming (Inbound) port or port range for this type of
application (e.g. 2300-2400, 47624)
Public Type: Select the Inbound port protocol type: “TCP”, “UDP” or “BOTH”
Wireless Router RNX-EasyN4
User Manual
Popular Applications: This section lists the more popular applications that require
multiple connections. Select an application from the
Popular Applications selection. Once you have selected an
application, select a location (1-5) in the Copy to selection
box and then click the Copy to button. This will
automatically list the Public Ports required for this popular
application in the location (1-5) you specified.
Add Port Triggering
Fill in the "Trigger Port", "Trigger Type”, “Public Port”, "Public Type",
"Public Port" and "Description" of the setting to be added and then Click
<Add>. The Port Triggering setting will be added into the "Current TriggerPort Table" below. If you happen to make a mistake, just click <Clear> and the
fields will be cleared.
Remove Port Triggering
If you want to remove Special Application settings from the "Current TriggerPort Table", select the Port Triggering settings you want to remove in the table
and then click <Delete Selected>. If you want remove all Port Triggering
settings from the table, just click the <Delete All> button. Click <Reset> will
clear your current selections.
Wireless Router RNX-EasyN4
User Manual
- Application Layer Gateway (ALG)
You can select applications that need ALG support. The router will let the selected
application to correctly pass through the NAT gateway.
- UPNP
With UPnP, all PCs in you Intranet will discover this router automatically. So, you
don’t have to configure your PC and it can easily access the Internet through this
router.
Wireless Router RNX-EasyN4
User Manual
Enable/Disable UPnP: You can enable or Disable the UPnP feature here. After you
enable the UPnP feature, all client systems that support
UPnP,
like
Windows
XP,
can
discover
this
router
automatically and access the Internet through this router
without having to configure anything. The NAT Traversal
function provided by UPnP can let applications that support
UPnP connect to the internet without having to configure
the virtual server sections.
- Quality of Service (QoS)
QoS can let you classify Internet application traffic by source/destination IP
address and port number. You can assign priority for each type of application and
reserve bandwidth for it. The packets of applications with higher priority will always
go first. Lower priority applications will get bandwidth after higher priority applications
Wireless Router RNX-EasyN4
User Manual
get enough bandwidth. This can let you have a better experience in using critical real
time services like Internet phone, video conference …etc. All the applications not
specified by you are classified as rule “Others”. The rule with a smaller priority
number has a higher priority; the rule with a larger priority number has a lower
priority. You can adjust the priority of the rules by moving them up or down.
Priority Queue
This can put the packets of specific protocols in High/Low Queue. The packets
in High Queue will process first.
Wireless Router RNX-EasyN4
User Manual
Unlimited Priority Queue: The LAN IP address will not be bounded in the QoS
limitation.
High/Low Priority Queue: This can put the packets in the protocol and port range to
High/Low QoS Queue.
Bandwidth Allocation:
This can reserve / limit the throughput of specific protocols and port range. You
can set the upper bound and Lower bound.
Wireless Router RNX-EasyN4
User Manual
Type: Specify the direction of packets. Upload, download or both.
IP range: Specify the IP address range. You could also fill one IP address
Protocol: Specify the packet type. The default ALL will put all packets in the QoS
priority Queue.
Port range: Specify the Port range. You could also fill one Port.
Policy: Specify the policy the QoS, Min option will reserve the selected data rate in
QoS queue. Max option will limit the selected data rate in QoS queue.
Rate: The data rate of QoS queue.
Disabled: This could turn off QoS feature.
- Routing
You can set enable Static Routing to let the router forward packets by your routing
policy.
Wireless Router RNX-EasyN4
User Manual
Destination LAN IP: Specify the destination LAN IP address of static routing rule.
Subnet Mask: Specify the Subnet Mask of static routing rule.
Default Gateway: Specify the default gateway of static routing rule.
Hops: Specify the Max Hops number of static routing rule.
Interface: Specify the Interface of static routing rule.
„ TOOLS Settings
- Admin
You can change the password required to log into the broadband router's system
web-based management. By default, the password is: admin. Passwords can contain
0 to 12 alphanumeric characters, and are case sensitive.
Wireless Router RNX-EasyN4
User Manual
Old Password: Fill in the current password to allow changing to a new password.
New Password: Enter your new password and type it again in Repeat New
Password for verification purposes
Remote management
This allows you to designate a host in the Internet the ability to configure the
Broadband router from a remote site. Enter the designated host IP Address in
the Host IP Address field.
Wireless Router RNX-EasyN4
User Manual
Host Address: This is the IP address of the host in the Internet that will have
management/configuration access to the Broadband router from a
remote site. If the Host Address is left 0.0.0.0 this means anyone
can access the router’s web-based configuration from a remote
location, providing they know the password.
Port: The port number of the remote management web interface.
Enabled: Check to enable the remote management function.
Click <Apply> at the bottom of the screen to save the above configurations.
- Time
The Time Zone allows your router to reference or base its time on the settings
configured here, which will affect functions such as Log entries and Firewall settings.
Time Setup:
Wireless Router RNX-EasyN4
User Manual
Synchronize with the NTP server
Time Zone: Select the time zone of the country you are currently in. The router will
set its time based on your selection.
NTP Time Server: The router can set up external NTP Time Server.
Daylight Savings: The router can also take Daylight Savings into account. If you
wish to use this function, you must select the Daylight Savings
Time period and check/tick the enable box to enable your
daylight saving configuration.
Click <Apply> at the bottom of the screen to save the above configurations.
Synchronize with PC
You could synchronize timer with your Local PC time.
Wireless Router RNX-EasyN4
User Manual
PC Date and Time: This field would display the PC date and time.
Daylight Savings: The router can also take Daylight Savings into account. If you
wish to use this function, you must select the Daylight Savings
Time period and check/tick the enable box to enable your
daylight saving configuration.
Click <Apply> at the bottom of the screen to save the above configurations.
- DDNS
DDNS allows you to map the static domain name to a dynamic IP address. You
must get an account, password and your static domain name from the DDNS service
Wireless Router RNX-EasyN4
User Manual
providers. This router supports DynDNS, TZO and other common DDNS service
providers.
Enable/Disable DDNS: Enable or disable the DDNS function of this router
Server Address: Select a DDNS service provider
Host Name: Fill in your static domain name that uses DDNS.
Username: The account that your DDNS service provider assigned to you.
Password: The password you set for the DDNS service account above
Click <Apply> at the bottom of the screen to save the above configurations.
- Power
Wireless Router RNX-EasyN4
Saving power in WLAN mode can be enabled / disabled in this page.
- Diagnosis
This page could let you diagnosis your current network status.
User Manual
Wireless Router RNX-EasyN4
User Manual
- Firmware
This page allows you to upgrade the router’s firmware. To upgrade the firmware of
your Broadband router, you need to download the firmware file to your local hard
disk, and enter that file name and path in the appropriate field on this page. You can
also use the Browse button to find the firmware file on your PC.
Wireless Router RNX-EasyN4
User Manual
Once you’ve selected the new firmware file, click <Apply> at the bottom of the
screen to start the upgrade process
- Back-up
This page allows you to save the current router configurations. When you save the
configurations, you also can re-load the saved configurations into the router through the
Restore Settings. If extreme problems occur you can use the Restore to Factory
Defaults to set all configurations to its original default settings.
Wireless Router RNX-EasyN4
User Manual
Backup Settings: This can save the Broadband router current configuration to a file
named "config.bin" on your PC. You can also use the <Upload>
button to restore the saved configuration to the Broadband router.
Alternatively, you can use the "Restore to Factory Defaults" tool
to force the Broadband router to perform a power reset and
restore the original factory settings.
- Reset
You can reset the broadband router when system stops responding correctly or
stop functions.
Wireless Router RNX-EasyN4
User Manual
Wireless Router RNX-EasyN4
User Manual
13 Repeater Mode
Repeater mode has limited settings compared to the AP mode. Choose “Repeater
mode” on the top right corner of the configuration page.
System restarts and connects to the IP address http://192.168..0.1
You will see the configuration homepage under “REPEATER” mode now.
„ System
- Status
System status section allows you to monitor the current status of your router. You can
use the status page to quickly see if you have any updated firmware available (bug fixes,
updates). You can navigate from this page with a few interesting options for reminding or
skipping this page forever & so forth.
Once you click on <OK> button to go to the requested page, you can see the status
page of the RNX-EASYN4.
Wireless Router RNX-EasyN4
User Manual
You can see the UP time, hardware information, serial number as well as firmware
version information.
LAN Settings: This page displays the Broadband router LAN port’s current LAN &
WLAN information. It also shows whether the DHCP Server function is enabled /
disabled. Wireless configuration details such as SSID, Security settings, BSSID,
Channel number, mode of operation are briefly shown.
WLAN Settings: View Broadband router’s current configuration settings. Device Status
displays the configuration settings you’ve configured in the Wizard / Basic Settings
/ Wireless Settings section
- LAN
The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry
level user, try accessing a website from your browser. If you can access website without
a glitch, just do not change any of these settings.
Click <Apply> at the bottom of this screen to save the changed configurations.
Wireless Router RNX-EasyN4
User Manual
IP address: It is the router’s LAN IP address (Your LAN clients default gateway IP
address). It can be changed based on your own choice.
IP Subnet Mask: Specify a Subnet Mask for your LAN segment.
802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree function
is enabled, this router will use the spanning tree protocol to
prevent network loops.
- Schedule
Add schedule, edit schedule options allow configuration of power savings services. Fill
in the schedule and select type of service. Click <Apply> to implement the settings.
Wireless Router RNX-EasyN4
User Manual
The schedule table lists the pre-schedule service-runs. You can select any of them
using the check box.
Wireless Router RNX-EasyN4
User Manual
- Event Log
View operation log of RNX-EASYN4. This page shows the current system log of
the Broadband router. It displays any event occurred after system start up. At the
bottom of the page, the system log can be saved <Save> to a local file for further
processing or the system log can be cleared <Clear> or it can be refreshed
<Refresh> to get the most updated information. When the system is powered down,
the system log will disappear if not saved to a local file.
Wireless Router RNX-EasyN4
User Manual
- Monitor
Show the network packets histogram for network connection on WAN, LAN &
WLAN. Auto refresh keeps information updated frequently.
- Language
This Wireless Router support multiple language of web pages, you could select
your native language here.
Wireless Router RNX-EasyN4
User Manual
„ Wireless
-Basic
You can set parameters that are used for the wireless stations to connect to this router.
The parameters include Mode, ESSID, Channel Number and Associated Client.
Wireless Router RNX-EasyN4
User Manual
Radio: Enable or Disable Wireless function
Band: Allows you to set the AP fixed at 802.11b, 802.11g or 802.11n mode. You
can also select B+G mode to allow 802.11b and 802.11g clients at the same
time.
Enable ESSID: You can specify the maximum ESSID number.
ESSID1~3: Allow you to specify ESSID of WLAN.
Site Survey: You can scan the current Wireless Access Point and connect on it.
Wireless Router RNX-EasyN4
User Manual
-Clint List
This WLAN Client Table shows the Wireless client associate to this Wireless
Router.
Wireless Router RNX-EasyN4
User Manual
-Policy
The Broadband router can allow you to set up the Wireless Access Policy.
Communication between Wireless clients:
Allow Wireless Client to communicate with other Wireless Client on specific SSID.
Communication between Wireless clients and wired clients:
Allow Wireless Client to communicate with other Wireless Client on specific SSID
and Wired Client on the switch. Or Wireless Client will allow to access WAN port only
Wireless Router RNX-EasyN4
User Manual
„ Tools
- Admin
You can change the password required to log into the broadband router's system
web-based management. By default, the password is: admin. Passwords can contain
0 to 12 alphanumeric characters, and are case sensitive.
Old Password: Fill in the current password to allow changing to a new password.
Wireless Router RNX-EasyN4
User Manual
New Password: Enter your new password and in Repeat New Password for
verification purposes
Click <Apply> at the bottom of the screen to save the above configurations
Remote management
This allows you to designate a host in the Internet the ability to configure the
Broadband router from a remote site. Enter the designated host IP Address in the Host
IP Address field.
Host Address: This is the IP address of the host in the Internet that will have
management/configuration access to the Broadband router from a
remote site. If the Host Address is left 0.0.0.0 this means anyone
can access the router’s web-based configuration from a remote
location, providing they know the password.
Port: The port number of the remote management web interface.
Enabled: Check to enable the remote management function.
Click <Apply> at the bottom of the screen to save the above configurations.
Wireless Router RNX-EasyN4
User Manual
- Time
The Time Zone allows your router to reference or base its time on the settings
configured here, which will affect functions such as Event Log entries and Schedule
settings.
Time Setup:
Synchronize with the NTP server
Wireless Router RNX-EasyN4
User Manual
Time Zone: Select the time zone of the country you are currently in. The router
will set its time based on your selection.
NTP Time Server: This accept local the IP Address of Local NTP Time Server
Address.
Daylight Savings: The router can also take Daylight Savings into account. If
you wish to use this function, you must select the Daylight
Savings Time period and check/tick the enable box to
enable your daylight saving configuration.
Click <Apply> at the bottom of the screen to save the above configurations
Synchronize with PC
You could synchronize timer with your Local PC time.
PC Date and Time: This field would display the PC date and time.
Wireless Router RNX-EasyN4
User Manual
Daylight Savings: The router can also take Daylight Savings into account. If you wish to
use this function, you must select the Daylight Savings Time period
and check/tick the enable box to enable your daylight saving
configuration.
Click <Apply> at the bottom of the screen to save the above configurations.
- Power
Saving power in WLAN mode can be enabled / disabled in this page.
Wireless Router RNX-EasyN4
User Manual
- Diagnosis
This page could let you diagnosis your current network status.
- Firmware
This page allows you to upgrade the router’s firmware. To upgrade the firmware of
your Broadband router, you need to download the firmware file to your local hard disk,
and enter that file name and path in the appropriate field on this page. You can also use
the Browse button to find the firmware file on your PC.
Wireless Router RNX-EasyN4
User Manual
Once you’ve selected the new firmware file, click <Apply> at the bottom of the
screen to start the upgrade process
Wireless Router RNX-EasyN4
User Manual
- Back-up
The page allows you to save (Backup) the router’s current configuration settings.
When you save the configuration setting (Backup) you can re-load the saved
configuration into the router through the Restore selection. If extreme problems
occur you can use the Restore to Factory Defaults selection, this will set all
configurations to its original default settings (e.g. when you first purchased the
router).
Backup Settings: This can save the Broadband router current configuration to a file
named "config.bin" on your PC. You can also use the
<Upload> button to restore the saved configuration to the
Broadband router. Alternatively, you can use the "Restore to
Factory Defaults" to force the Broadband router to perform a
power reset and restore the original factory settings.
Wireless Router RNX-EasyN4
User Manual
- Reset
You can reset the broadband router when system stops responding correctly or
stop functions.
Wireless Router RNX-EasyN4
User Manual
Appendix A – FCC Interference Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
z
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
z
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Wireless Router RNX-EasyN4
User Manual
Appendix B – IC Interference Statement
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum gain of 2 dBi. Antenna having
a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50
ohms.
Thank you for purchasing a quality Rosewill Product.
Please register your product at : www.rosewill.com for complete warranty information and future support for your product.