Samsung SID-50P User's Manual
Add to my manuals2 Pages
Samsung SID-50P boasts excellent image quality thanks to its high sensitivity COLOR CCD and optimized DSP CHIP, providing a horizontal resolution of 540 TV lines. With its built-in SSNR function, it reduces low illuminance noise and improves the signal-to-noise ratio, resulting in sharp images even in dark conditions. Additionally, its auto functions, including ATW, backlight compensation, gain control, and noise reduction, ensure optimal image quality in various lighting conditions.
advertisement
SALES NETWORK
•
SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,
Gyeonggi-do 462-703, Korea
TEL : +82-31-740-8137~8141 FAX : +82-31-740-8145
•
SAMSUNG OPTO-ELECTRONICS UK, LTD.
Samsung House, 1000 Hillswood Drive, Hillswood
Business Park Chertsey, Surrey KT16 OPS
TEL : +44-1932-45-5308 FAX : +44-1932-45-5325 www.samsungtechwin.com
www.samsungcctv.com
•
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD.
7 Pingchang Rd, Nankai Dist. Tianjin 300190, P.R China
TEL : +86-22-2761-4724(33821) FAX : +86-22-2761-6514
P/No. : Z6806-0715-01A
VAN 06. 03
HIGH RESOLUTION MINI DOME CAMERA
INSTRUCTION MANUAL
SID-50
About this manual
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
INFORMATION-This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will required to correct the interference at his own expense.
WARNING -Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
WARNING - To prevent electric shock and risk of fire hazards:
Do NOT use other than specified power source.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to all local codes.
MINI DOME CAMERA 2 USER’S MANUAL
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and proper input power voltage. In order that you can understand this manual thoroughly, we'll introduce our model description.
SID-50 SERIES
• NTSC models
SID-50N
• PAL models
SID-50P
Model Description
• SID-50X • SIGNAL SYSTEM
Signal system
N NTSC Model
P PAL Model
FEATURES
Horizontal Resolution 540 TV Lines
Clear image quility has been achieved by employing a CCD with 410,000 pixels(NTSC), 470,000 pixels(PAL) and optimized WINNER3 DSP CHIP which provides a horizontal resolution of 540 TV lines.
High Sensitivity
The built-in high sensitivity COLOR CCD enables a clear image even in 0.05Lux or lower illumination.
SSNR (Samsung Super Noise Reduction)
By using built-in SSNR function manufactured by SAMSUNG TECHWIN, the amount of low illuminance noise has been significantly reduced, and the signal-to-noise ratio (S/N) as well as horizontal resolution have been improved, resulting in a clear and sharp image display even in the dark.
Pan and Tilt
Pan and tilt are available after installing camera.
MINI DOME CAMERA 3 USER’S MANUAL
WARNING
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, a fire may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not handle the camera with wet hands
It could cause an electric shock.
MINI DOME CAMERA 4 USER’S MANUAL
PRECAUTIONS
Do not install the camera in extreme temperature conditions.
Do not install or use the camera in an environment where the humidity is high.
Do not touch the front glass of the camera.
Never keep the camera face to strong light directly.
Only use the camera under conditions where temperatures are between -10˚C and +50˚C.
Be especially careful to provide ventilation when operating under high temperatures.
It can cause the image quality to be poor.
Do not install the camera under unstable lighting conditions.
Never use the camera close to a gas or oil leak.
It is one of the most important parts of camera.
Be careful not to be stained by fingerprint.
Do not drop the camera or subject them to physical shocks.
It can damage the CCD.
Do not expose the camera to rain or spill beverage on it.
Severe lighting change or flicker can cause the camera to work improperly.
It can cause malfunctions to occur.
Do not disassemble the camera.
There are no user-serviceable parts inside it.
MINI DOME CAMERA 5 USER’S MANUAL
It can cause malfunctions to occur.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode the electronic components.
Notes
• If the camera is exposed to spotlight or object reflecting the strong light, smear or blooming may occur.
• Please check the power whether it satisfies the normal specification before connecting the camera.
MINI DOME CAMERA 6 USER’S MANUAL
GETTING TO KNOW YOUR CAMERA
Front
Pan Base
You can rotate the lens from 360˚
Bottom
Tilt Base
You can adjust up and down the camera(20°~90°).
MINI DOME CAMERA 7 USER’S MANUAL
Power Input Terminal
BNC Jack
Accessories
User Manual Quick Install Guide
M4 Taping Screw 2EA Cable Rubber
Template
INSTALLATION
Installing Camera
1. Fix the camera to a ceiling or a wall using two screws.
2. After fixing it, adjust its pan base and tilt base properly.
Hole
3. After adjusting them, secure the shield case and dome-cover.
Screw
Shield Case
Dome Cover
MINI DOME CAMERA 8 USER’S MANUAL
Notes
• When installing the camera on a ceiling or a wall, not to disturb adjustment of Tilt Base angle fix the BNC-Power Cable on the Pan Base clip.
<Installing the camera on a ceiling> <Installing the camera on a wall>
BNC-Power Cable
Pan Base clip
Connection to Power
•Connect the adapter to the power input connector as shown in the figure below. Use a
DC12V 500mA. (The Adapter is not provided with the Dome Camera.)
DOME Camera
Adapter (not provided)
Power Input Connector
MINI DOME CAMERA 9 USER’S MANUAL
For DC Power Type
Resistance of copper wire [at 20C˚ (68˚F)]
Copper wire size (AWG) #24(0.22mm
2 ) #22(0.33mm
2 )
Resistance ( Ω / m)
Voltage Drop (V/m)
0.078
0.028
0.050
0.018
#20(0.52mm
2 ) #18(0.83mm
2 )
0.030
0.011
0.018
0.006
• As the voltage drop according to the length of the cable in the above table, a camera may malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
Connection to Monitor
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
•As a connecting method varies according to instruments, refer to the manual supplied with the instrument.
•Connect the cable after power is turned off.
•Set the 75Ω / Hi-Z selection switch. If it is a intermediate device, switch it to Hi-z and if it is final device, switch it to 75Ω. (Please refer to the Monitor Manual.)
BNC
Intermediate Monitor
DOME Camera
MINI DOME CAMERA 10 USER’S MANUAL
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 360°,
Tilting angle: 20˚~90˚)
Tilt Base Holding
Screws
Tilt Base
You can adjust up and down the camera (20˚~90˚).
Pan Base
You can rotate the lens from 360˚
Pan Base Holding Screw
1) Adjustment Panning angle: After attaching the dome camera to a ceiling or a wall, adjust the panning angle for better monitoring area by rotating the Pan Base. The panning angle can be adjusted 360˚ freely.
2) Adjustment Tilting angle: After attaching the dome camera to a ceiling or a wall, adjust the tilting angle for better monitoring area by rotating the Tilt Base. The tilting angle can be adjusted to 20˚ from 90˚ freely. (based the ceiling surface)
Notes
• After loosening Pan or Tilt Base holding screws, adjust its angle. And then tighten screws again.
• In case of adjusting the tilting, do not take the lens for preventing hysical shocks. Please take the Tilt Base.
• This dome camera is to be installed on the ceiling by factory default. In case of using camera on the wall, readjust the Tilt angle as page 8 (Notes).
MINI DOME CAMERA 11 USER’S MANUAL
CAMERA OPERATION
The SID-50 includes the following built in functions
Auto Functions
Electronic Shutter
Speed
WHITE BALANCE
BACKLIGHT
GAIN CONTROL
SSNR
(Noise Reduction)
SENS UP
SHARPNESS
Setting Value
ESC
ATW
MIDDLE
MIDDLE
LOW
ON
ON
Descriptions
The speed is controlled according to the brightness of the screen.
It can be used within the color temperature range 1,800K~10,500K(Ex fluorescent light, outdoor, sodium vapor lamp or inside tunnels)
The gain increases within the range of
6dB~34dB
The gain increases or decreases within the range of 6dB~34dB
There is sufficient reduction in noise levels without causing much ghost imaging
It helps maintain a bright, clear screen image by automatically detecting changes in the level in low light levels without causing much ghost imaging.
The outline of the video image becomes cleaner and more distinctive as the level of
SHARPNESS increases.
MINI DOME CAMERA 12 USER’S MANUAL
TROBLESHOOTING
If you have trouble operating your camera, refer to the following. If the guidelines do not enable you to solve the problem, contact an authorized technician.
The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
• The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime.
The contrast on the screen is too weak.
• Adjust the contrast feature of the monitor.
• If the camera is exposed under too strong light, change the camera position.
• Adjust the lens BACK FOCUS again.
The camera is not work properly, and the surface of the camera case is hot.
• Check that you have connected the camera to a proper power (DC12V ).
DIMENSION
99.2
63.5
99.2
67
99.2
R 41.2
2-Ø 4.2
MINI DOME CAMERA 13 USER’S MANUAL
SPECIFICATION
ITEM
R
I
C
T
E
L
E
C
A
L
Power Source
Total Pixels
CCD Effective Pixels
SIZE
Sync.
Scanning System
Synchronization
Frequency
LENS(Built-in)
Resolution
Video Output
S/N(Y signal)
Min.Illumination
Auto Functions
Monitoring Pan
Angle Tilt
Operating temperature/Humidity
Dimention
Weight
SID-50N SID-50P
DC 12V±10%/Max. 1.8W
811(H) x 508(V) 795(H) x 596(V)
768(H) x 494(V) 752(H) x 582(V)
1/3 inch Super HAD CCD
2:1 Interlace
Internal Only
Horizontal:15.734 KHz/Vertical :59.94 Hz Horizontal: 15.625 KHz/Vertical : 50Hz
Built-in Fixed Lens 120 f=3.0mm, F2.0
540 TV Lines(Min.)
CVBS : 1.0Vp-p/75
50 dB (AGC Off,Weight ON)
0.05Lux/F1.2(Sens-up), 0.3Lux/F1.2
Electronic shutter speed
WHITE BALANCE
BACKLIGHT
Gain Control
AUTO
AUTO
AUTO
AUTO
SENS-UP
SSNR(Noise Control)
SHARPNESS
Manual 360
Manual 20 ~ 90
-10˚C to +50˚C / 30% to 80% RH
AUTO
AUTO
AUTO
99.2mm(W) x 99.2mm(H) x 67mm(D)
200g
MINI DOME CAMERA 14 USER’S MANUAL
DECLARATION OF CONFORMITY
Application of Council Directive(s)
Manufacturer's Name
Manufacturer's Address
89 / 336 / EEC
SAMSUNG TECHWIN CO., LTD
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment
Model Name
Beginning Serial NO.
Year of Manufacture
Conformance to
MINI DOME CAMERA
SID-50
S6300001
2006. 03. 01
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name
Position
YOUNG TAEK SON
QUALITY CONTROL MANAGER
Full Name
Position
Date 2006. 03. 01
Place
Date
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project