Maytag Mgr8772ws Quick Specs

30" (76.2 cm) Freestanding Gas Range
PRODUCT MODEL NUMBERS
MGR8670W
MGR8772W
PRODUCT DIMENSIONS
MGR8875W
Natural gas: This range is design-certified by CSA International
for use with Natural gas or, after proper conversion, for use with LP
gas.
● This range is factory set for use with Natural gas. See “Gas
Conversions” section. The model/serial rating plate located
behind the storage drawer on the right-hand side oven door
frame has information on the types of gas that can be used. If the
types of gas listed do not include the type of gas
available, check with the local gas supplier.
C*
A
B*
LP gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier. See “Gas
Conversions” section.
● A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is
required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit
serving only this range be provided.
E
D
G
F
A. 28¹⁄₂" (72.4 cm) to 29" (73.7 cm)
depth with handle to backguard
standoffs.
29" (73.7 cm) depth with handle
(KitchenAid models only)
B. 35⁵⁄₈" (90.5 cm) cooktop height
(maximum) with leveling legs
screwed all the way in*
C. 47¹⁄₈" (119.7 cm) overall height
(maximum) with leveling legs
screwed all the way in*
D. 29⁷⁄₈" (75.9 cm) width
*Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
CABINET OPENING DIMENSIONS
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the range, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
Range may be installed with zero clearance to combustible
construction at the rear and on the sides below the cooktop.
D
B
C
A
E
G
F
M
N
G
H
J
H
I
K
E. 26³⁄₄" (67.9 cm) depth to
background standoffs
F. Model/serial number plate
(located behind the
storage drawer on the
left-hand side of the oven
frame)
G. Rating number plate
(located behind the
storage drawer on the
right-hand side of the
oven frame)
L
J
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
A. 18" (45.7 cm) upper cabinet to countertop
B. 13" (33.0 cm) upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to the top of the cooktop, see NOTE.
E. 30¹⁄₈" (76.5 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of the range to the side
wall or other combustible material
G. 6" (15.2 cm) width of H (area for gas and electric)
H. Recommended area for gas and electric installation
I. 6" (15.2 cm) height of notched area in H
J. 3⁵⁄₁₆" (8.4 cm) distance from side of range to H
K. 3" (7.6 cm) width of notched area in H
L. 3" (7.6 cm) distance from wall
M. Cabinet door or hinges should not extend into the cutout.
N. 19" (48.3 cm) height of H
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal
cabinet is covered by not less than ¹⁄₄" (0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10258096A
07-30-09