Sharp EL-6053 User's Manual

3. Using World clock
ELECTRONIC ORGANIZER
6. Setting alarms
1. Press CLOCK once or twice to display World
clock (without “ ”).
2. Press PREV or NEXT to select the desired
city.
EL-6053
EL-6810
OPERATION MANUAL
NOTICE
• SHARP strongly recommends that separate
permanent written records be kept of all
important data. Data may be lost or altered in
virtually any electronic memory product under
certain circumstances. Therefore, SHARP
assumes no responsibility for data lost or
otherwise rendered unusable whether as a
result of improper use, repairs, defects, battery
replacement, use after the specified battery life
has expired, or any other cause.
• SHARP assumes no responsibility, directly or
indirectly, for financial losses or claims from
third persons resulting from the use of this
product and any of its functions, such as stolen
credit card numbers, loss or alteration of stored
data, etc.
• The information provided in this manual is
subject to change without notice.
In Europe:
This equipment complies with the requirements of
Directive 89/336/EEC as amended by 93/68/EEC.
Dieses Gerät entspricht den Anforderungen der EGRichtlinie 89/336/EWG mit Änderung 93/68/EWG.
Ce matériel répond aux exigences contenues dans la
directive 89/336/CEE modifiée par la directive 93/68/
CEE.
Dit apparaat voldoet aan de eisen van de richtlijn 89/336/
EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC
med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti della direttiva
89/336/EEC come emendata dalla direttiva 93/68/EEC.
Η εγκατάσταση αυτή ανταπïκρίνεται στις απαιτήσεις
των ïδηγιών της Ευρωπαïκής Ενωσης 89/336/ΕÃΚ,
Þπως ï κανïνισµÞς αυτÞς συµπληρώθηκε απÞ την
ïδηγία 93/68/ΕÃΚ.
Este equipamento obedece às exigências da directiva 89/
336/CEE na sua versão corrigida pela directiva 93/68/
CEE.
Este aparato satisface las exigencias de la Directiva 89/
336/CEE modificada por medio de la 93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjen 89/336/
EEC så som kompletteras av 93/68/EEC.
Dette produktet oppfyller betingelsene i direktivet 89/336/
EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivin 89/336/EEC vaatimukset,
jota on muutettu direktiivillä 93/68/EEC.
Notes
• While operations are described mainly for EL- • One of the models described in this manual
6053, unless otherwise specified, the text
may not be available in some countries.
materials apply to both models. In case of need,
the operations are described as “For EL-6810
only:”.
The Organizer has 3 kinds of alarm:
1. Daily alarm ........ beeps every day at the alarm
time (for 1 minute), when
“ ” is turned on.
2. Hourly alarm ...... beeps every hour when
minutes reach “00”, when
4. Changing the cities between Home
“ ” is turned on.
and World clocks
3. Schedule alarm .. beeps at the time for all the
You can change the home city for a city in another
schedule entries (for 1
time zone without adjusting the stored correct
minute), when “
” is
time.
turned on. (Refer to
1. Press CLOCK once or twice to display World
“Schedule Mode”.)
clock (without “ ”).
Press any key to stop the alarm beeping.
NEXT
2. Press PREV or
and select the desired
Setting/Changing the daily alarm time
city to be set as the new home city.
1. Press CLOCK once or twice to display Home
3. Press SHIFT SET to change the cities
clock (with “ ”).
between Home and World clocks.
2. Press ALARM to
• The previous home city is now set as the
ALARM
display the daily
world city (without “ ”).
alarm
screen.
4. Press CLOCK to check the home city.
A12–00
(The display differs
• The selected city in step 2 is set as the home
between the 12-hour and 24-hour clock.)
city (with “ ”).
3. Press SHIFT SET .
5. Press CLOCK to recheck the world city, and
press PREV or NEXT to select the new world 4. Enter the time.
5. Press ENTER .
city, if needed.
• The daily alarm time is set.
5. Setting daylight saving time (DST:
summer time)
Turning the alarms on and off
An alarm sounds only when the respective symbol
( , , or
) is turned on.
1. Press CLOCK once or twice to display Home
Display Home clock (press CLOCK once or twice)
or World clock.
and press ALARM to display the daily alarm
2. Press DST .
screen.
“#” is displayed. The time is set 1 hour ahead.
Each time you press ALARM while the daily alarm
To clear DST, press DST to clear “#”. The time
screen is displayed, the combination of symbols
is set 1 hour behind.
switches.
Notes
Note
• DST can be set independently in either Home or
• Alarms sound even when the Organizer is
World clock.
turned off.
• When DST is set for one world city, it is used
for all cities displayed in World clock.
Telephone Mode
Part Names
EL-6053
EL-6810
q
w
q
w
e t
t
e
r
q
w
e
r
t
Power ON/OFF key
Cursor keys
Search keys
RESET switch
Mode keys
The following notations are used for
key operations.
➝ CM : Clear memory
(in Calculator mode)
➝ U : Letter “U”
: Turn the touch
➝ SHIFT
tone on and off
➝ V : Letter “V”
r
• Yellow colored functions are operated by
pressing SHIFT (“SHIFT” is turned on) and the
appropriate keys.
• In this manual, only the display symbols
necessary for explanation of this product are
shown.
Using the Organizer for the First Time
Be sure to perform the following operations
before using the Organizer for the first time.
1. Remove the isolating film that is affixed to the
battery holder on the back of the unit.
2. Press the RESET switch with a ball-point pen
or similar object.
“RESET?” is displayed.
3. Press SHIFT ENTER to initialize the
Organizer.
After “RESET!” is displayed, Home clock is
displayed. (See “Clock Mode”.) You have
deleted all the memory contents now.
NOTES
• If the Organizer is subjected to strong,
extraneous electrical noises or shocks during
use, an abnormal condition may occur in which
OFF
no keys (including ON ) will respond. Press
the RESET switch and press SHIFT ENTER to
delete all the memory contents.
• To minimize battery consumption, the Organizer
is designed to automatically turn off when no
key has been pressed for approximately 7
minutes.
• The key touch tone is turned on and off by
. When the tone is turned
pressing SHIFT
on, “ ” is turned on.
Changing the Guidance Language
Entering Characters
Entering symbols and letters with an accent
mark
• To enter a symbol, press SMBL repeatedly until
the desired symbol appears:
@#$£¥
( )~’: / \_&<>ß!? ¡¿
• To enter a letter with an accent mark, press
SHIFT SHIFT to turn “SHIFT LOCK” on, and
press the appropriate key repeatedly. (Refer to
the “QUICK REFERENCE GUIDE” inside the
cover.)
• To turn “SHIFT LOCK” off, press SHIFT again.
Making corrections
Home city (with “
Date
Time
”)
Day of the week
LON
MON
2001– 1– 1
A12–00–00
Each time you press CLOCK , the clock switches
between Home and World clocks. (For World
clock, “ ” is not displayed.)
1. Before setting the clock
• The default setting for the date is “YYYY/MM/
DD” (year-month-day). To change the setting to
“MM/DD/YYYY” (month-day-year) or “DD/MM/
YYYY” (day-month-year):
1. Press CLOCK once or twice to display
Home clock (with “ ”).
2. Press SHIFT DATE TYPE .
3. Press PREV or NEXT to select the desired
type.
4. Press ENTER to store the new setting.
• To change the 12-hour clock to the 24-hour
clock, press 12 24 (“A” or “P” is cleared).
Each time you press 12 24 , the clock
switches.
• In the period of daylight saving time/summer
time, press DST in advance (“#” is displayed).
2. Setting the clock
1. Press CLOCK once or twice to display Home
clock (with “ ”).
2. Press SHIFT SET to start setting.
The cursor starts to flash on the city name.
EL-6053/6810,E.E65
EL-6053/6810
1
English Front sheet
Storing telephone entries
1. Press TEL once or
NAME?
twice to display the
Telephone mode
screen (in this case,
TEL1).
2. Enter the name, e.g. SMITH SPACE ROBERT,
and press ENTER .
3. Enter the address, e.g. 18 SPACE EAST
SPACE ROAD, and press ENTER .
4. Enter the E-mail
harpsec.com_
address, e.g.
SROB SMBL
(to enter “ @ ”)
SHARPSEC.COM, and press ENTER .
• The E-mail address is automatically entered
in small letters.
Cursor
The cursor (_) indicates the position for entering a
character. Move the cursor with the cursor keys
).
(
Inserting characters
Each time INS is pressed, a space is inserted at
the cursor position to allow you to enter a
character.
Deleting characters
Press DEL to delete the character at the cursor
position.
Press C•CE to clear all the characters that you
have entered and not stored yet.
Zone
No.
0
1
2
3
3.3
4
5
6
6.3
7
7.3
8
8.3
9
9.3
Display
TNG
WLG
NOU
SYD
ADL
TYO
HKG
BKK
RGN
DAC
DEL
KHI
KBL
DXB
THR
City
TONGA
WELLINGTON
NOUMEA
SYDNEY
ADELAIDE
TOKYO
HONG KONG
BANGKOK
YANGON
DHAKA
NEW DELHI
KARACHI
KABUL
DUBAI
TEHRAN
Zone
No.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Display
City
MOW
CAI
PAR
LON
AZ0
-2H
RIO
CCS
NYC
CHI
DEN
LAX
ANC
HNL
MID
MOSCOW
CAIRO
PARIS
LONDON
AZORES ISLANDS
2hrs behind LON
RIO DE JANEIRO
CARACAS
NEW YORK
CHICAGO
DENVER
LOS ANGELES
ANCHORAGE
HONOLULU
MIDWAY
Field
The 1st line:
Name, address,
E-mail address
(and web address
(URL) for EL-6810
only)
Number of
Allowable
characters
characters
36 characters Alphabetic letters,
or under
numbers, symbols,
“+ – × ÷ .”, space
The 2nd and the
3rd lines:
Phone number
Numbers, space, –,
F (Fax), P (Pager)
Notes
• The symbol “NAME”, “ADDRESS”, or “E-mail”
(or “URL” for EL-6810 only) is turned on while
entering in each field.
• To skip entry of an address, E-mail address,
(web address (URL),) or number, press ENTER
when “ADDRESS?”, “E-MAIL?”, (“URL?”,) or
“NUMBER?” is displayed. However, entering a
person’s name cannot be skipped.
Schedule Mode
Schedule mode is used for storing schedule
details (36 characters or under), date and time
(year, month, day, hour, and minute).
In the 1st line the same characters are allowable
as in Telephone mode.
1. Press SCHEDULE to
SCHEDULE?
display the Schedule
mode screen.
2. Enter the details and
press ENTER .
3. Enter the date and time.
• The types of date and time are the same as
the types set for the clock.
• To enter a single-digit date or time, enter “0”
and the digit (e.g. “O2”).
4. Press ENTER to store in the memory.
Notes
• Schedules for the following dates can be stored:
January 1901 to December 2098.
• If an attempt is made to store an entry without a
date or time, or with an invalid date or time,
“ERROR!” appears briefly. Enter the correct
date and time and press ENTER .
2. Alarm for Schedule mode
When the schedule alarm (“
”) is turned on, it
is set for all the schedule entries. Beeping sounds
for 1 minute when the time for a schedule entry is
reached. Press any key to stop the alarm. The
schedule alarm cannot be set for an individual
entry.
Memo Mode
Notes or other pieces of information that are not
appropriate for Telephone or Schedule mode can
be entered for convenience.
In the 1st line the same characters are allowable
as in Telephone mode. In the 2nd and the 3rd
lines you can enter numbers, –, and space. (36
characters or under can be entered in each line.)
2. Enter the memo item
UNION BANK
and numbers.
01
E.g. UNION SPACE
272–0011223 _
BANK ENTER
01
272-0011223
3. Press ENTER to store in the memory.
Storing memo entries
1. Press MEMO to
display the Memo
mode screen.
MEMO?
Notes for storing and recalling entries
For EL-6810 only: Press BS to delete the
character at the left of the cursor.
3. Press PREV or NEXT to select the desired
time zone. (Refer to the list of cities described
below.)
• Enter the city name, if needed (6 characters
or under). Only one changed name for Home
clock can be stored.
4. Press to move the cursor to the year.
5. Enter the year (4 digits), the month, and the
day (2 digits each).
• The built-in calendar extends from January
1st, 1901, to December 31st, 2098.
6. Press AM•PM to select “A” (morning) or “P”
(afternoon) for the 12-hour clock.
7. Enter the time (hours and minutes).
Note: P12-00: noon, A12-00: midnight
8. Press ENTER . The clock starts from “00”
seconds.
Notes
• To enter a single-digit date or time, enter “0”
and the digit (e.g. “02”).
• If you enter an invalid date or time, “ERROR!”
appears briefly. Enter the correct date and time
and press ENTER .
5. Enter the phone
NUMBER?
number, and then
2–3456–7890
the fax number if
3456–7891 _
needed, e.g.
012-3456-7890
F SPACE SPACE SPACE 3456-7891, and
press ENTER .
• “STORED!” appears briefly, then the Telephone
mode screen is displayed. The telephone entry
is now stored.
For EL-6810 only:
• To enter “ @ ”, simply press @ instead of
SMBL .
• After entering the E-mail address and
pressing ENTER , enter the web address
(URL), e.g. WWW.SHARP-USA.COM, and
press ENTER .
Move the cursor to the character to be corrected.
Enter the correct character to replace the previous
one.
Clock Mode
Home clock
For EL-6810 only:
• Moreover, EL-6810 has the web address (URL)
field that follows the E-mail address field.
• Instead of pressing TEL once or twice in the
following operations, press TEL1 or TEL2 once.
1. Storing schedule entries
Guidance messages can be displayed in 7
To change the language, press SHIFT LANGUAGE
languages – English, Dutch, Portuguese, Italian,
followed by PREV or NEXT to select the desired
German, French, and Spanish. After initializing the language, then press ENTER .
Organizer, the default setting is English.
• Alphanumeric letters, symbols, and “+ – × ÷ .”
can be entered into the dot display area (the 1st
line).
• Numbers and some characters (only space, –,
and F and P in Telephone mode) can be entered
into the number display area (the 2nd and the
3rd lines).
• Basically letters are entered in capital letters
(“CAPS” is turned on). To enter small letters,
press CAPS to turn “CAPS” off.
Telephone mode is composed of two files, TEL1
(“1” is turned on) and TEL2 (“2” is turned on).
Use these files for convenience, e.g. business
and private files.
A telephone entry consists of name, address,
E-mail address, and number fields.
• When the memory is full, “MEMORY FULL!”
appears briefly, and the entry cannot be stored.
• When the symbol “ ” or “ ” is turned on,
more information exists. Press or
to
switch the display.
Checking details of entries in Telephone mode
• To display each field on the 1st line, follow the
symbol “ ” or “ ” and press or . (The
symbol above the 1st line shows each field.)
• Pressing E-MAIL displays the E-mail address
on the 1st line directly.
For EL-6810 only: Pressing E-MAIL ( WWW )
again displays the web address (URL) on the
1st line. Each time you press E-MAIL ( WWW ),
the display switches between the E-mail and the
web addresses.
• Press and hold
to start the auto scroll on the
1st line. Press again to stop or restart the
scroll. Press C•CE to quit the auto scroll.
Recalling entries – Telephone, Schedule, Memo –
First press the desired mode key.
NEXT : Recalls entries in forward order
PREV
: Recalls entries in reverse order
Sorting order
• Telephone and memo entries are stored by the
first character of the person’s name or memo
item in the following order (case sensitive):
Sequential search
Press NEXT or PREV in each mode.
Direct search
• Enter the first characters (7 characters or
under) of the person’s name, schedule details,
or memo item, and press NEXT or PREV .
Then press NEXT or PREV to continue
performing a direct search.
• Schedule entries are stored by date and time.
Note
• When there is no (further or relevant) entry to
be recalled, “NOT FOUND!” appears briefly, and
the display returns to the mode screen.
PRINTED IN CHINA/IMPRIMÉ EN CHINE
00BTO (TINSE0355EHZZ)
3/6/2000, 3:34 PM
Editing or deleting entries – Telephone, Schedule, Memo –
Editing
1. Recall the entry to be edited.
2. Press EDIT . The cursor starts to flash.
• In Telephone mode press ENTER several
times to display each field (the address field
and so on).
3. Press , , , or to move the cursor to
the position to be edited.
4. Enter, insert, or delete characters (refer to
“Entering Characters”).
• To cancel editing, press C•CE .
5. Press ENTER several times (until “STORED!”
appears briefly) to finish editing and to store
the entry.
Deleting
1. Recall the entry to be deleted.
2. Press DEL .
• “DELETE?” is displayed.
• To cancel the deletion operation, press
C•CE .
3. Press ENTER to delete the entry.
Calculation examples
Example
0.
Operation
Display
C•CE
24
2
4
–5.5
34 57
91.
45
102.
(The addend becomes a
constant.)
68×25=1700
68 25
1700.
Calculation
68×40=2720
40
2720.
(The multiplicand becomes
Be sure to press C•CE , C•CE , and CM to clear
a constant.)
the display and memory before performing a
200×10%=20
200 10 %
20.
calculation.
9÷36=25%
9
36 %
25.
Note
200+(200×10%)=220 200 10 %
220.
• When , , , or is pressed, the respective
500–(500×20%)=400 500 20 %
400.
symbol, +, –, ×, or ÷ is displayed. (In the
46=(43)2=4096
4
4096.
examples in this manual, these symbols are not
1/8=0.125
8
0.125
described.)
M
CM 25
25×5=125
5 M+
125.
M
If an error occurs
–)84÷3=28
84
3 M–
28.
M
If the calculation result or the integer section in
+)68+17=85
68
17 M+
85.
M
the numerical value in the memory exceeds 10
182
182.
RM
ED
EDD
digits or if a number is divided by zero (0), an
25–9=4
25 9
4.
error occurs (“ERR” is displayed).
1234567890×145 1234567890
ERR
=179012344050
145
17.90123440
C•CE
17.90123440
(–24+2)÷4=–5.5
34+57=91
45+57=102
(17.90123440×1010=179012344000)
Currency/Unit Conversion Mode
1. Setting a currency rate
2. Converting currency/unit
1. Press CALC/CONV
EURO
USD
several times to
display the currency
0.
conversion mode
screen (refer to “Calculator mode”).
Example: 1 CAD (Canada dollars)
= 0.66 USD (US dollars)
2. Press NEXT NEXT NEXT to change the
display and press SHIFT SET . The initial
character of “CAD” starts to flash.
• You can change each currency name by
entering characters (up to 4 in each) and
using , if needed.
3. Press ENTER . “0” starts to flash.
4. Enter the rate (up to
CAD
USD
10 digits).
0.66
.
066
5. Press ENTER to
store in the memory.
You need to set the conversion rate before making
the currency conversion.
Example: Convert 500 CAD into USD using the
rate that you have set.
1. Display the screen: “CAD → USD”.
2. Enter the value to be converted.
500
3. Press to convert
CAD
USD
CAD into USD.
• To convert in
330.
reverse order (e.g.
200 USD into CAD), enter 200 and press .
• You can use the unit conversion in the same
manner. You cannot change the units or the
rates for units.
• The conversion result may have a slight error
as a result of rounding off the number (e.g. up
to 2 decimal places for currency conversions).
Use the conversion result for reference.
Game Mode
Press
GAME
to play the game “ALPHA ATTACK”.
For EL-6810 only: Each time you press GAME ,
the display switches between “BLACKJACK” and
“ALPHA ATTACK”.
ALPHA ATTACK
Type in characters (A to Z, 0 to 9) displayed on
the 1st line to clear them. The game is divided
into 20 levels in speed.
1. Press GAME to
display the following ALPHA ATTACK
Game mode screen.
01
2. Enter the level
Level
number (2 digits
from 01 to 20).
• 01: slow, 20: fast
3. Press ENTER to
EY3KW
start a game.
4. Press the same key
01
as the first character
at the left end of the 1st line. (In this case,
press keys in the order: E → Y → 3 → K →
W.)
• Pressing the correct key in the correct order
deletes the character.
• When 12 characters are displayed in each
level, the game continues in the faster level
(up to 20).
• When no more characters can be displayed,
the game is over. The Game mode screen
with the level when the game is over is
displayed.
1. Registering a password and storing 2. Turning Secret function on and off
secret entries
When Secret function is on, “
” is not
Up to 6 characters can be registered as the
password.
• One password is valid for Telephone, Schedule,
and Memo modes.
If the password is forgotten, you cannot delete the
password only. You have to delete all the memory
contents. (Perform steps 2 and 3 as described in
the section, “Using the Organizer for the First
Time”.) As a safeguard, make a written record of
the password.
Calculator Mode
The Organizer can
calculate numbers of up
to 10 digits. Press
CALC/CONV several
times to display the Calculator mode screen
(Calculator → Currency conversion → Unit
conversion → Calculator...).
Secret Function
For EL-6810 only: BLACKJACK (Twenty-one)
Make your “hand” (the total of the numbers on
the cards) close to 21, without going over 21.
1. Press GAME to
display the following BLACKJACK
Game mode screen.
30
2. Press ENTER to
Your chips
start a game. The left
2 cards are dealt for you. (One is facing up and
one is facing down.)
3. Agree the left-displayed maximum bet (up to
10) or enter the fewer bet. Pressing also
can bet to the maximum.
4. Press SPACE to
Your hand The dealer’s
see your hand.
hand
Each time you
J28
4
press SPACE , a
new card is dealt.
10
20
• “J”, “Q”, and “K”
Your bet Your chips
are counted as 10.
• “A” can be counted as 1 or 11.
• When first 2 cards are “A” and a face card
(“J”, “Q”, or “K”), your hand is
“BLACKJACK”.
5. Press ENTER to
Your total The dealer’s
total
stop being dealt and
hold your hand. The
J28
32K4
dealer’s hand and
20
19
20
20
the results are
displayed.
Your bet Your chips
• When you win,
your total flashes and your bet is doubled.
• When you win with “BLACKJACK”, your bet
is tripled.
6. Press ENTER and display the Game mode
screen.
• When you have no more chips to bet, the
game is over.
• To quit the game, press C•CE or any mode
key. Your chips are stored for the next time.
• To return your chips to 30, press DEL and
ENTER on the Game mode screen.
Registering a password
1. Press TEL ( TEL1 or TEL2 ), SCHEDULE , or
MEMO to display “NAME?”, “SCHEDULE?”,
or “MEMO?”.
2. Press SECRET .
PASSWORD?
3. Enter the password (case sensitive), e.g. ABC.
4. Press SECRET to register it.
• The display returns to the screen in step 1
with the symbol “
”.
• If “ERROR!” appears briefly, a password has
already been registered. Enter the correct
password or delete the password and all the
memory contents.
5. Press SECRET SECRET to turn Secret
function on. “
” disappears.
Storing secret entries
1. Enter characters in Telephone, Schedule, or
Memo mode when “
” is not displayed
(Secret function is on).
• When “
” is displayed, press SECRET
SECRET to turn Secret function on.
2. Press SECRET before pressing ENTER to
store. “
” appears.
3. Press ENTER to store a secret entry in the
memory.
• “STORED!” appears briefly, and the display
returns to the mode screen without “
”
(Secret function is on).
• You cannot display the secret entry until you
turn Secret function off.
• In addition to the memory size for characters
(in the 1st line) and numbers (in the 2nd and
1. Press TEL ( TEL1 or TEL2 ), SCHEDULE , or
the 3rd lines), each entry requires the following
MEMO to display “NAME?”, “SCHEDULE?”, or
memory size:
“MEMO?”.
Telephone entry ..... EL-6053: 5 bytes
2. Press SHIFT M•CK .
EL-6810: 6 bytes
CAPACITY
The number of
Schedule entry ....... 8 bytes (including date
remaining bytes is
6254
and time)
displayed briefly.
Memo entry ........... 3 bytes
Notes
• The Organizer can store up to the following
2. Deleting all the memory contents
bytes in the memory (excluding the Calculator
mode memory).
Perform steps 2 and 3 as described in the section,
EL-6053: 7671 bytes/EL-6810: 66838 bytes
“Using the Organizer for the First Time”.
• 1 byte is required per character (in the 1st line) • To cancel the deletion operation, press C•CE
for telephone, schedule, and memo entries.
instead of SHIFT ENTER in step 3.
• 1 byte is required for 2 digits in the number part
(in the 2nd and the 3rd lines) of telephone and
memo entries. (When there is an odd number
of digits in a number entry, the last digit
occupies 1 byte.)
Turning Secret function off
1. Press TEL ( TEL1 or TEL2 ), SCHEDULE , or
MEMO and check that “
” is not displayed.
2. Press SECRET . “PASSWORD?” is displayed.
3. Enter the password and press SECRET .
•“
” is displayed and you can display
secret entries.
• If you enter an incorrect password,
“ERROR!” appears briefly. Follow the above
steps and enter the correct password.
• Even when Secret function is turned off, it
will be automatically turned on (“
” will
disappear):
A)when you press GAME , CLOCK , or
CALC/CONV ,
or B)after the power is turned off manually
or automatically.
Turning Secret function on
1. Press TEL ( TEL1 or TEL2 ), SCHEDULE , or
MEMO and check that “
” is displayed.
2. Press SECRET .
The password is displayed. Memorize it again.
3. Press SECRET again.
” disappears and you cannot display
“
secret entries.
3. Changing the password
1. Turn Secret function off (“
” appears).
2. Press SECRET . The password is displayed.
3. Press EDIT .
The initial character of the password starts to
flash.
4. Enter, or edit characters and make a new
password.
5. Press SECRET . The new password is now
registered.
Caring for Your Organizer
• Do not carry the Organizer in the back pocket of • Since this product is not waterproof, do not use
slacks or trousers.
it or store it where fluids can splash onto it.
• Do not drop the Organizer or apply excessive
• Clean only with a soft, dry cloth.
• Use only a SHARP approved service facility.
force to it.
• Do not subject the Organizer to extreme
temperatures.
Replacing Battery
Battery used
Type
Model
EL-6053: CR2025
Lithium battery
EL-6810: CR2032
Quantity
1
• Improper replacement of the battery may
change or lose the memory contents.
• Be sure to write down any important
information stored in the memory before
replacing the battery.
• Make sure the power is turned off before
replacing the battery.
OFF
• Do not press ON until the battery replacement
procedure is completed.
1. Precautions
Since improper use of the battery may cause
leakage or explosion, strictly observe the
following instructions.
• Insert the battery with the positive side (+)
correctly facing up.
• Never throw the battery into a fire because it
might explode.
• Keep the battery out of the reach of children.
Because the battery in the Organizer was installed
at the factory, it may become depleted before the
specified expiration time is reached.
2. Battery replacement
If the display becomes dim and difficult to read,
immediately replace the battery with a new one.
Continued use of the Organizer with an exhausted
battery can alter or clear the memory contents.
For EL-6053 only:
• Do not use a metallic object to pry out the
battery. The Organizer will be subjected to an
electrical shock and all the memory contents
will be cleared.
• Complete the replacement of the battery within
1 minute, otherwise all the memory contents
may be cleared.
For EL-6053 only:
OFF
1. Press ON to turn the power off.
2. Loosen the screw and remove the battery
holder cover on the back of the unit. (Slide the
cover off.)
3. Remove the exhausted
battery by prying it out
from the holder with
the corner of the
holder cover. (Fig. 1)
4. Install a new battery
with the positive side
(+) facing up into the
Fig. 1
holder.
5. Replace the holder cover and secure it with the
screw.
OFF
6. Press ON to turn the power on.
• If nothing appears on the display, press the
RESET switch and press C•CE .
• Do not press SHIFT ENTER . Pressing
SHIFT ENTER clears all the memory
contents.
7. Set the clock.
For EL-6810 only:
OFF
1. Press ON to turn the power off.
2. Loosen the screw and remove the battery
holder cover on the back of the unit. (Slide the
cover off.)
3. Install a new battery with the positive side (+)
facing up into the upper or lower empty holder.
(Fig. 1)
4. Remove the exhausted battery by prying it out
with a ball-point pen. (Fig. 2)
5. Replace the holder cover and secure it with the
screw.
OFF
6. Press ON to turn the power on.
• If nothing appears on the display, press the
RESET switch and press C•CE .
• Do not press SHIFT ENTER . Pressing
SHIFT ENTER clears all the memory
contents.
7. Set the clock.
Fig. 1
Memory Storage
1. Checking memory storage
displayed.
• You can display, edit, or delete entries
except secret entries.
• You can enter new entries as secret or
non-secret.
When Secret function is off, “
” is
displayed.
• You can display, edit, or delete secret
entries only. (You cannot display nonsecret entries.)
• You cannot enter a new entry.
Fig. 2
Specifications
• Model: EL-6053
EL-6810
• Power consumption: EL-6053: 0.003 W
EL-6810: 0.003 W
• Product name: Electronic Organizer
• Operating temperature: 0°C to 40°C
(32°F to 104°F)
• Display: 3 lines of 12 digits
• Memory capacity: EL-6053: 7671 bytes
EL-6810: 66838 bytes
• Clock mode:
Accuracy: ± 60 seconds/month at 25°C/77°F
Display: Year, month, day, day of the
week, hour, minute, second, AM/PM
Clock function: 12-hour/24-hour format
(switchable), 3 kinds of date type
(switchable), world clock function, daylight
saving time (summer time) display, daily
alarm, hourly alarm
• Telephone mode: Entering and recalling of
telephone entry (name, address, E-mail
address, and phone number; and web address
(URL) for EL-6810 only)
• Schedule mode: Entering and recalling of
schedule entry (details, year, month, day, hour,
and minute), schedule alarm
• Memo mode: Entering and recalling of memo
entry
• Calculator mode: 10 digits (with calculation
status symbols), arithmetical calculations,
percentage, square root, memory calculation,
etc.
• Currency/unit conversion mode:
5 kinds of currency conversion (editable) and 9
kinds of unit conversion
• Game mode: EL-6053: 1 game
EL-6810: 2 games
• Power supply: 3V … (DC), lithium battery
EL-6053: CR2025 × 1
EL-6810: CR2032 × 1
• Auto-power off: Approx. 7 minutes
• Battery life: Approx. 2 years at ambient
temperature of 25°C/77°F, assuming the
following daily use: 30 minutes display, alarm
sounding for 20 seconds and key touch tone
turned on/off 100 times.
• Weight (including battery):
EL-6053: Approx. 88 g (0.194 lb.)
EL-6810: Approx. 105 g (0.231 lb.)
• Dimensions:
EL-6053:
Open:
125.0 mm (W) × 168.5 mm (D) × 8.3 mm (H)
4-29/32" (W) × 6-5/8" (D) × 5/16" (H)
Closed:
125.0 mm (W) × 86.3 mm (D) × 12.0 mm (H)
4-29/32" (W) × 3-13/32" (D) × 15/32" (H)
EL-6810:
Open:
139.0 mm (W) × 174.7 mm (D) × 9.5 mm (H)
5-15/32" (W) × 6-7/8" (D) × 3/8" (H)
Closed:
139.0 mm (W) × 89.5 mm (D) × 13.7 mm (H)
5-15/32" (W) × 3-17/32" (D) × 17/32" (H)
• Accessories: 1 lithium battery (installed),
operation manual
SHARP CORPORATION
EL-6053/6810,E.E65
EL-6053/6810 English
2
Rear sheet
3/6/2000, 3:35 PM