Sharp EL-6900 Owner's Manual

ELECTRONIC ORGANIZER
EL-6900
OPERATION MANUAL
NOTICE
• SHARP strongly recommends that separate
permanent written records be kept of all
important data. Data may be lost or altered in
virtually any electronic memory product under
certain circumstances. Therefore, SHARP
assumes no responsibility for data lost or
otherwise rendered unusable whether as a
result of improper use, repairs, defects, battery
replacement, use after the specified battery life
has expired, or any other cause.
• SHARP assumes no responsibility, directly or
indirectly, for financial losses or claims from
third persons resulting from the use of this
product and any of its functions, such as stolen
credit card numbers, loss or alteration of stored
data, etc.
• The information provided in this manual is
subject to change without notice.
Part Names
1
2
3
4
6
Power ON/OFF key
Cursor keys
Search keys
Mode keys
RESET switch
TRANSLATOR key
• Purple colored functions are operated by
pressing SHIFT (“SHIFT” is turned on) and the
appropriate keys.
• In this manual, only the display symbols
necessary for explanation of this product are
shown.
The following notations are used for
key operations.
➝ CM : Clear memory
(in Calculator mode)
➝ U : Letter “U”
➝
SHIFT
➝
V
: Turn the touch tone on
and off
: Letter “V”
Using the Organizer for the First Time
Be sure to perform the following operations
before using the Organizer for the first time.
1. Remove the isolating film that is affixed to the
battery holder on the back of the unit.
2. Press the RESET switch with a ball-point pen
or similar object.
“RESET?” is displayed.
3. Press SHIFT ENTER to initialize the
Organizer.
After “RESET!” is displayed, Home clock is
displayed. (See “Clock Mode”.) You have
deleted all the memory contents now.
Setting/Changing the daily alarm time
1. Press CLOCK once or twice to display Home
clock (with “ ”).
1. Press CLOCK once or twice to display Home
2. Press ALARM to
ALARM
or World clock.
display the daily
2. Press DST .
alarm screen.
A12–00
“#” is displayed. The time is set 1 hour ahead.
(The display differs
To clear DST, press DST to clear “#”. The time
between the 12-hour and 24-hour clock.)
is set 1 hour behind.
3. Press SHIFT SET .
Notes
4. Enter the time.
• DST can be set independently in either Home or 5. Press ENTER .
World clock.
• The daily alarm time is set.
• When DST is set for one world city, it is used
Turning
the alarms on and off
for all cities displayed in World clock.
An alarm sounds only when the respective symbol
( , , or
) is turned on.
6. Setting alarms
Display Home clock (press CLOCK once or twice)
The Organizer has 3 kinds of alarm:
and press ALARM to display the daily alarm
1. Daily alarm ........ beeps every day at the alarm screen.
time (for 1 minute), when
Each time you press ALARM while the daily alarm
“ ” is turned on.
screen is displayed, the combination of symbols
2. Hourly alarm ...... beeps every hour when
switches.
minutes reach “00”, when
Note
“ ” is turned on.
• Alarms sound even when the Organizer is
3. Schedule alarm .. beeps at the time for all the
turned off.
schedule entries (for 1
minute), when “
” is
turned on. (Refer to
“Schedule Mode”.)
Press any key to stop the alarm beeping.
Telephone Mode
5
q
w
e
r
t
y
5. Setting daylight saving time (DST:
summer time)
NOTES
• If the Organizer is subjected to strong,
extraneous electrical noises or shocks during
use, an abnormal condition may occur in which
OFF
no keys (including ON ) will respond. Press
the RESET switch and press SHIFT ENTER to
delete all the memory contents.
• To minimize battery consumption, the Organizer
is designed to automatically turn off when no
key has been pressed for approximately 7
minutes.
• The key touch tone is turned on and off by
pressing SHIFT
. When the tone is turned
on, “ ” is turned on.
Changing the Guidance Language
Guidance messages can be displayed in 7
To change the language, press SHIFT LANGUAGE
PREV or NEXT
followed by
to select the
languages – English, Dutch, Portuguese, Italian,
German, French, and Spanish. After initializing the desired language, then press ENTER .
Organizer, the default setting is English.
Telephone mode is composed of two directions of 6. Enter the phone
NUMBER?
storage memory. Pressing TEL toggles between
number, and then
2–3456–7890
the fax number if
“1” and “2” on the display.
3456–7891 _
needed, e.g.
Use these files for convenience, e.g. business
012-3456-7890
and private files.
F SPACE SPACE SPACE 3456-7891, and
A telephone entry consists of name, address,
press ENTER .
E-mail address, web address (URL) and number
• “STORED!” appears briefly, then the Telephone
fields.
mode screen is displayed. The telephone entry
Storing telephone entries
is now stored.
1. Press TEL once or
Number of
Allowable
Field
NAME?
twice to display the
characters
characters
Telephone mode
36 characters Alphabetic letters,
The 1st line:
or under
Name, address,
numbers, symbols,
screen.
E-mail address
“+ – × ÷ .”, space
2. Enter the name, e.g. SMITH SPACE ROBERT,
and web address
(URL)
and press ENTER .
3. Enter the address, e.g. 18 SPACE EAST
Numbers, space, –,
The 2nd and the
F (Fax), P (Pager)
3rd lines:
SPACE ROAD, and press ENTER .
Phone number
4. Enter the E-mail
harpsec.com_
address, e.g.
Notes
SROB SMBL
• The symbol “NAME”, “ADDRESS”, “E-mail”, or
(to enter “ @ ”)
“URL” is turned on while entering in each field.
SHARPSEC.COM, and press ENTER .
• The E-mail address is automatically entered • To skip entry of an address, E-mail address,
web address (URL), or number, press ENTER
in small letters.
when “ADDRESS?”, “E-MAIL?”, “URL?”, or
5. Enter the web address (URL), e.g.
“NUMBER?” is displayed. However, entering a
WWW.SHARPUSA.COM, and press ENTER .
person’s name cannot be skipped.
Schedule Mode
Schedule mode is used for storing schedule
details (36 characters or under), date and time
(year, month, day, hour, and minute).
In the 1st line the same characters are allowable
as in Telephone mode.
Pressing SCHEDULE/MEMO toggles between
Schedule and Memo mode.
1. Storing schedule entries
1. Press
SCHEDULE/MEMO
Entering Characters
• Alphanumeric letters, symbols, and “+ – × ÷ .”
can be entered into the dot display area (the 1st
line).
• Numbers and some characters (only space, –,
and F and P in Telephone mode) can be entered
into the number display area (the 2nd and the
3rd lines).
• Basically letters are entered in capital letters
(“CAPS” is turned on). To enter small letters,
press CAPS to turn “CAPS” off.
Entering symbols and letters with an accent
mark
• To enter a symbol, press SMBL repeatedly until
the desired symbol appears:
@#$£¥
( )~’: / \_&<>ß!? ¡¿æµ¢
• To enter a letter with an accent mark, press
SHIFT SHIFT to turn “SHIFT LOCK” on, and
press the appropriate key repeatedly. (Refer to
the “QUICK REFERENCE GUIDE” inside the
cover.)
• To turn “SHIFT LOCK” off, press SHIFT again.
Making corrections
Move the cursor to the character to be corrected.
Enter the correct character to replace the previous
one.
Cursor
The cursor (_) indicates the position for entering a
character. Move the cursor with the cursor keys
(
).
Inserting characters
Each time INS is pressed, a space is inserted at
the cursor position to allow you to enter a
character.
Deleting characters
Press DEL to delete the character at the cursor
position.
Press C•CE to clear all the characters that you
have entered and not stored yet.
4. Press ENTER to store in the memory.
Notes
• Schedules for the following dates can be stored:
January 1901 to December 2098.
• If an attempt is made to store an entry without a
date or time, or with an invalid date or time,
“ERROR!” appears briefly. Enter the correct
date and time and press ENTER .
SCHEDULE?
once or twice to
display the Schedule
mode screen.
2. Enter the details and press ENTER .
3. Enter the date and time.
• The types of date and time are the same as
the types set for the clock.
• To enter a single-digit date or time, enter “0”
and the digit (e.g. “O2”).
2. Alarm for Schedule mode
When the schedule alarm (“
”) is turned on, it
is set for all the schedule entries. Beeping sounds
for 1 minute when the time for a schedule entry is
reached. Press any key to stop the alarm. The
schedule alarm cannot be set for an individual
entry.
Memo Mode
Notes or other pieces of information that are not
appropriate for Telephone or Schedule mode can
be entered for convenience.
In the 1st line the same characters are allowable
as in Telephone mode. In the 2nd and the 3rd
lines you can enter numbers, –, and space. (36
characters or under can be entered in each line.)
2. Enter the memo item
UNION BANK
and numbers.
01
E.g. UNION SPACE
272–0011223 _
BANK ENTER
01
272-0011223
3. Press ENTER to store in the memory.
Storing memo entries
1. Press
SCHEDULE/MEMO
MEMO?
once or twice to
display the Memo
mode screen.
Clock Mode
Home clock
Home city (with “
Date
Time
”)
Day of the week
LON
WED
2003– 1– 1
A12–00–00
Each time you press CLOCK , the clock switches
between Home and World clocks. (For World
clock, “ ” is not displayed.)
1. Before setting the clock
Notes
• To enter a single-digit date or time, enter “0”
and the digit (e.g. “02”).
• If you enter an invalid date or time, “ERROR!”
appears briefly. Enter the correct date and time
and press ENTER .
Zone
No.
0
1
2
3
3.3
4
5
6
6.3
7
7.3
8
8.3
9
9.3
Display
City
Zone
No.
TNG TONGA
10
WLG WELLINGTON 11
NOU NOUMEA
12
SYD SYDNEY
13
ADL ADELAIDE
14
TYO TOKYO
15
HKG HONG KONG
16
BKK BANGKOK
17
RGN YANGON
18
DAC DHAKA
19
DEL NEW DELHI
20
KHI KARACHI
21
KBL KABUL
22
DXB DUBAI
23
THR TEHRAN
24
Display
City
MOW
CAI
PAR
LON
AZ0
-2H
RIO
CCS
NYC
CHI
DEN
LAX
ANC
HNL
MID
MOSCOW
CAIRO
PARIS
LONDON
AZORES ISLANDS
2hrs behind LON
RIO DE JANEIRO
CARACAS
NEW YORK
CHICAGO
DENVER
LOS ANGELES
ANCHORAGE
HONOLULU
MIDWAY
• The default setting for the date is “YYYY/MM/
DD” (year-month-day). To change the setting to
“MM/DD/YYYY” (month-day-year) or “DD/MM/
YYYY” (day-month-year):
1. Press CLOCK once or twice to display
Home clock (with “ ”).
2. Press DATE TYPE .
PREV or NEXT
3. Press
to select the
desired type.
4. Press ENTER to store the new setting.
3. Using World clock
• To change the 12-hour clock to the 24-hour
1. Press CLOCK once or twice to display World
clock, press 12 24 (“A” or “P” is cleared).
clock (without “ ”).
Each time you press 12 24 , the clock
PREV or NEXT
2. Press
to select the
switches.
desired city.
• In the period of daylight saving time/summer
time, press DST in advance (“#” is displayed).
Notes for storing and recalling entries
• When the memory is full, “MEMORY FULL!”
appears briefly, and the entry cannot be stored.
• When the symbol “ ” or “ ” is turned on,
to
more information exists. Press or
switch the display.
Checking details of entries in Telephone mode
• To display each field on the 1st line, follow the
symbol “ ” or “ ” and press or . (The
symbol above the 1st line shows each field.)
Recalling entries – Telephone, Schedule, Memo –
First press the desired mode key.
: Recalls entries in forward order
NEXT
PREV
: Recalls entries in reverse order
Sequential search
or
Press NEXT
PREV
1. Press CLOCK once or twice to display Home
clock (with “ ”).
2. Press SHIFT SET to start setting.
The cursor starts to flash on the city name.
PREV or NEXT
3. Press
to select the
desired time zone. (Refer to the list of cities
described below.)
• Enter the city name, if needed (6 characters
or under). Only one changed name for Home
clock can be stored.
4. Press to move the cursor to the year.
5. Enter the year (4 digits), the month, and the
day (2 digits each).
• The built-in calendar extends from January
1st, 1901, to December 31st, 2098.
6. Press AM/PM to select “A” (morning) or “P”
(afternoon) for the 12-hour clock.
7. Enter the time (hours and minutes).
Note: P12-00: noon, A12-00: midnight
8. Press ENTER . The clock starts from “00”
seconds.
You can change the home city for a city in another
time zone without adjusting the stored correct
time.
1. Press CLOCK once or twice to display World
clock (without “ ”).
PREV or NEXT
2. Press
and select the
desired city to be set as the new home city.
3. Press SHIFT SET to change the cities
between Home and World clocks.
• The previous home city is now set as the
world city (without “ ”).
4. Press CLOCK to check the home city.
• The selected city in step 2 is set as the home
city (with “ ”).
5. Press CLOCK to recheck the world city, and
PREV or NEXT
to select the new
press
world city, if needed.
Sorting order
• Telephone and memo entries are stored by the
first character of the person’s name or memo
item in the following order (case sensitive):
in each mode.
Direct search
• Enter the first characters (8 characters or
under) of the person’s name, schedule details,
or memo item, and press NEXT
or
PREV . Then press NEXT
PREV to
or
continue performing a direct search.
4. Changing the cities between Home
and World clocks
2. Setting the clock
• Pressing E-MAIL displays the E-mail address
on the 1st line directly.
Pressing E-MAIL ( WWW ) again displays the
web address (URL) on the 1st line. Each time
you press E-MAIL ( WWW ), the display
switches between the E-mail and the web
addresses.
• Press and hold
to start the auto scroll on the
1st line. Press
again to stop or restart the
scroll. Press C•CE to quit the auto scroll.
• Schedule entries are stored by date and time.
Note
• When there is no (further or relevant) entry to
be recalled, “NOT FOUND!” appears briefly, and
the display returns to the mode screen.
Editing or deleting entries – Telephone, Schedule, Memo –
Editing
1. Recall the entry to be edited.
2. Press EDIT . The cursor starts to flash.
• In Telephone mode press ENTER several
times to display each field (the address field
and so on).
3. Press , , , or to move the cursor to
the position to be edited.
4. Enter, insert, or delete characters (refer to
“Entering Characters”).
• To cancel editing, press C•CE .
5. Press ENTER several times (until “STORED!”
appears briefly) to finish editing and to store
the entry.
Deleting
1. Recall the entry to be deleted.
2. Press DEL .
• “DELETE?” is displayed.
• To cancel the deletion operation, press
C•CE .
3. Press ENTER to delete the entry.
PRINTED IN CHINA/IMPRIMÉ EN CHINE
02ETO (TINSE0570EHZZ)
e00_el6900_65e.p65
1
6/4/2002, 10:23 AM
Calculator Mode
The Organizer can
calculate numbers of up
to 10 digits. Press
CALC/CONV several
times to display the Calculator mode screen
(Calculator → Currency conversion → Unit
conversion → Calculator...).
Calculation examples
Example
0.
Operation
Display
–5.5
34 57
91.
45
102.
(The addend becomes a
constant.)
68×25=1700
68 25
1700.
Calculation
68×40=2720
40
2720.
(The multiplicand becomes
Be sure to press C•CE , C•CE , and CM to clear
a constant.)
the display and memory before performing a
200×10%=20
200 10 %
20.
calculation.
9÷36=25%
9 36 %
25.
Note
200+(200×10%)=220 200 10 %
220.
• When , , , or is pressed, the respective
500–(500×20%)=400 500 20 %
400.
symbol, +, –, ×, or ÷ is displayed. (In the
46=(43)2=4096
4
4096.
examples in this manual, these symbols are not
1/8=0.125
8
0.125
described.)
M
CM 25
25×5=125
5 M+
125.
M
If an error occurs
–) 84÷3=28
84
3 M–
28.
M
If the calculation result or the integer section in
+) 68+17=85
68
17 M+
85.
M
the numerical value in the memory exceeds 10
182
182.
RM
앀앙
digits or if a number is divided by zero (0), an
앀앙앙
25–9=4
25 9
4.
error occurs (“ERR” is displayed).
1234567890×145 1234567890
145
ERR
=179012344050
17.90123440
C•CE
17.90123440
(–24+2)÷4=–5.5
34+57=91
45+57=102
C•CE
24
2
4
(17.90123440×1010=179012344000)
Currency/Unit Conversion Mode
1. Setting a currency rate
2. Converting currency/unit
1. Press CALC/CONV
EURO
USD
several times to
display the currency
0.
conversion mode
screen (refer to “Calculator mode”).
Example: 1 CAD (Canada dollars)
= 0.66 USD (US dollars)
NEXT
NEXT
2. Press NEXT
to change
the display and press SHIFT SET . The initial
character of “CAD” starts to flash.
• You can change each currency name by
entering characters (up to 4 in each) and
using , if needed.
3. Press ENTER . “0” starts to flash.
4. Enter the rate (up to
CAD
USD
10 digits).
0.66
.
066
5. Press ENTER to
store in the memory.
You need to set the conversion rate before making
the currency conversion.
Example: Convert 500 CAD into USD using the
rate that you have set.
1. Display the screen: “CAD → USD”.
2. Enter the value to be converted.
500
3. Press to convert
CAD
USD
CAD into USD.
• To convert in
330.
reverse order (e.g.
200 USD into CAD), enter 200 and press .
• You can use the unit conversion in the same
manner. You cannot change the units or the
rates for units.
• The conversion result may have a slight error
as a result of rounding off the number (e.g. up
to 2 decimal places for currency conversions).
Use the conversion result for reference.
Game Mode
Press
GAME
to play the game “BLACKJACK”.
Each time you press GAME , the display switches
between “ALPHA ATTACK” and “BLACKJACK”.
BLACKJACK (Twenty-one)
Make your “hand” (the total of the numbers on
the cards) close to 21, without going over 21.
1. Press GAME to
display the following BLACKJACK
Game mode screen.
30
2. Press ENTER to start
Your chips
a game. The left 2
cards are dealt for you. (One is facing up and
one is facing down.)
3. Agree the left-displayed maximum bet (up to
also
10) or enter the fewer bet. Pressing
can bet to the maximum.
4. Press SPACE to
Your hand The dealer’s
hand
see your hand.
Each time you
J28
4
press SPACE , a
new card is dealt.
10
20
• “J”, “Q”, and “K”
Your bet Your chips
are counted as 10.
• “A” can be counted as 1 or 11.
• When first 2 cards are “A” and a face card
(“J”, “Q”, or “K”), your hand is
“BLACKJACK”.
5. Press ENTER to
Your total The dealer’s
total
stop being dealt and
hold your hand. The
J28
32K4
dealer’s hand and
20
19
20
20
the results are
displayed.
Your bet Your chips
• When you win,
your total flashes and your bet is doubled.
• When you win with “BLACKJACK”, your bet
is tripled.
6. Press ENTER and display the Game mode
screen.
• When you have no more chips to bet, the
game is over.
• To quit the game, press C•CE or any mode
key. Your chips are stored for the next time.
• To return your chips to 30, press DEL and
ENTER on the Game mode screen.
ALPHA ATTACK
Type in characters (A to
Z, 0 to 9) displayed on
ALPHA ATTACK
the 1st line to clear them.
01
The game is divided into
20 levels in speed.
Level
1. Press GAME to display the following Game
mode screen.
2. Enter the level
EY3KW
number (2 digits
from 01 to 20).
01
• 01: slow, 20: fast
3. Press ENTER to start a game.
4. Press the same key as the first character at the
left end of the 1st line. (In this case, press keys
in the order: E → Y → 3 → K → W.)
• Pressing the correct key in the correct order
deletes the character.
• When 12 characters are displayed in each
level, the game continues in the faster level
(up to 20).
• When no more characters can be displayed,
the game is over. The Game mode screen
with the level when the game is over is
displayed.
Word Translation Function
• If there is no matching word, “NOT FOUND!”
is displayed. The word next in alphabetical
order will then be displayed.
PREV to scroll through
• Press NEXT
or
word list, or edit entry using the keyboard,
ENG
SPA
and press ENTER for another search.
• Press or to return to the source word.
Caution
• Spanish words stored in this device are
Press
twice (or
then ) to
those of Spain.
enter Spanish ➝ English mode.
• Only the masculine form of the noun will be
2. Enter the desired source word and press
displayed for nouns with both masculine and
ENTER .
feminine forms.
“English…” or “Spanish…” is displayed while
• Sometimes, two identical words will appear
conducting search. The matching
in the word list.
English or Spanish word will then be displayed.
• Enter European characters and spaces
• When the symbol “ ” is turned on, more
correctly. Otherwise, the unit may not be able
letters exist. To view remaining letters of long
to complete the search.
words that cannot be accommodated on the
screen, use to scroll right.
This device offers an English-Spanish bidirectional word translation function.
1. Press
to enter the English ➝ Spanish
translation mode.
Memory Storage
1. Checking memory storage
1. Press TEL or SCHEDULE/MEMO to display
“NAME?”, “SCHEDULE?”, or “MEMO?”.
2. Press SHIFT M•CK .
CAPACITY
The number of
remaining bytes is
6254
displayed briefly.
Notes
• The Organizer can store up to 34070 bytes in
the memory (excluding the Calculator mode
memory).
• One byte is required per character (in the 1st
line) for telephone, schedule, and memo
entries.
• One byte is required for 2 digits in the number
part (in the 2nd and the 3rd lines) of telephone
and memo entries. (When there is an odd
number of digits in a number entry, the last
digit occupies 1 byte.)
Up to 6 characters can be registered as the
password.
• One password is valid for Telephone, Schedule,
and Memo modes.
• In addition to the memory size for characters
(in the 1st line) and numbers (in the 2nd and
the 3rd lines), each entry requires the following
memory size:
Telephone entry ..... 6 bytes
Schedule entry ....... 8 bytes (including date
and time)
Memo entry ........... 3 bytes
2. Deleting all the memory contents
Perform steps 2 and 3 as described in the section,
“Using the Organizer for the First Time”.
• To cancel the deletion operation, press C•CE
instead of SHIFT ENTER in step 3.
2
When Secret function is on, “
” is not
displayed.
• You can display, edit, or delete entries
except secret entries.
• You can enter new entries as secret or
non-secret.
When Secret function is off, “
” is
displayed.
• You can display, edit, or delete secret
entries only. (You cannot display nonsecret entries.)
• You cannot enter a new entry.
Turning Secret function off
1. Press TEL or SCHEDULE/MEMO and check
that “
” is not displayed.
Turning Secret function on
1. Press TEL or SCHEDULE/MEMO and check
that “
” is displayed.
2. Press SECRET .
The password is displayed. Memorize it again.
3. Press SECRET again.
” disappears and you cannot display
“
secret entries.
3. Changing the password
1. Turn Secret function off (“
” appears).
2. Press SECRET . The password is displayed.
3. Press EDIT .
The initial character of the password starts to
flash.
4. Enter, or edit characters and make a new
password.
5. Press SECRET . The new password is now
registered.
Caring for Your Organizer
• Do not carry the Organizer in the back pocket of • Since this product is not waterproof, do not use
it or store it where fluids can splash onto it.
slacks or trousers.
• Do not drop the Organizer or apply excessive
• Clean only with a soft, dry cloth.
force to it.
• Use only a SHARP approved service facility.
• Do not subject the Organizer to extreme
temperatures.
Replacing Battery
Battery used
Type
Model
Quantity
Lithium battery
CR2032
1
• Improper replacement of the battery may
change or lose the memory contents.
• Be sure to write down any important
information stored in the memory before
replacing the battery.
• Make sure the power is turned off before
replacing the battery.
OFF
• Do not press ON until the battery replacement
procedure is completed.
1. Precautions
Since improper use of the battery may cause
leakage or explosion, strictly observe the
following instructions.
• Insert the battery with the positive side (+)
correctly facing up.
• Never throw the battery into a fire because it
might explode.
• Keep the battery out of the reach of children.
Because the battery in the Organizer was installed
at the factory, it may become depleted before the
specified expiration time is reached.
• Do not use a metallic object to pry out the
battery. The Organizer will be subjected to an
electrical shock and all the memory contents
will be cleared.
• Complete the replacement of the battery within
1 minute, otherwise all the memory contents
may be cleared.
OFF
1. Press ON to turn the power off.
2. Loosen the screw and remove the battery
holder cover on the back of the unit.
3. Remove the exhausted battery by prying it out
from the holder with the corner of the holder
cover. (Fig. 1)
4. Install a new battery with the positive side (+)
facing up into the holder.
5. Replace the holder cover and secure it with the
screw.
OFF
6. Press ON to turn the power on.
• If nothing appears on the display, press the
RESET switch and press C•CE .
• Do not press SHIFT ENTER . Pressing
SHIFT ENTER clears all the memory
contents.
7. Set the clock.
When removing the
battery, use the side
opposite the curved
corner of the battery
holder cover.
2. Battery replacement
If the display becomes dim and difficult to read,
immediately replace the battery with a new one.
Continued use of the Organizer with an exhausted
battery can alter or clear the memory contents.
Fig. 1
Specifications
• Model: EL-6900
• Game mode: 2 games
• Product name: Electronic Organizer
• Display: 3 lines of 12 digits
• Word Translation function:
Approx. 1200 words each
• Memory capacity: 34070 bytes
• Power consumption: 0.003 W
• Clock mode:
Accuracy: ± 60 seconds/month at 25°C/77°F
Display: Year, month, day, day of the
week, hour, minute, second, AM/PM
Clock function: 12-hour/24-hour format
(switchable), 3 kinds of date type
(switchable), world clock function, daylight
saving time (summer time) display, daily
alarm, hourly alarm
• Telephone mode: Entering and recalling of
telephone entry (name, address, E-mail
address, phone number, and web address
(URL))
• Schedule mode: Entering and recalling of
schedule entry (details, year, month, day, hour,
and minute), schedule alarm
• Memo mode: Entering and recalling of memo
entry
• Calculator mode: 10 digits (with calculation
status symbols), arithmetical calculations,
percentage, square root, memory calculation,
etc.
• Operating temperature: 0°C to 40°C
(32°F to 104°F)
• Power supply: 3V … (DC), lithium battery
CR2032 × 1
• Auto-power off: Approx. 7 minutes
• Battery life: Approx. 2 years at ambient
temperature of 25°C/77°F, assuming the
following daily use: 30 minutes display, alarm
sounding for 20 seconds and key touch tone
turned on/off 100 times.
• Weight (including battery):
Approx. 88 g (0.19 lb.)
• Dimensions:
Open:
128.0 mm (W) × 167.1 mm (D) × 9.0 mm (H)
5-1/32" (W) × 6-19/32" (D) × 11/32" (H)
Closed:
128.0 mm (W) × 86.6 mm (D) × 12.7 mm (H)
5-1/32" (W) × 3-13/32" (D) × 1/2" (H)
• Accessories: 1 lithium battery (installed),
operation manual
• Currency/unit conversion mode:
5 kinds of currency conversion (editable) and 9
kinds of unit conversion
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original
container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or
part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of
which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration
of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp
to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs
performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or
property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Your Product :
Electronic Organizer
Warranty Period for this Product :
One (1) year parts and labor from date of purchase.
Additional Items Excluded from
Warranty Coverage :
Any consumable items such as paper, maintenance cartridge, ink cartridges supplied with the Product or
to any equipment or any hardware, software, firmware, fluorescent lamp, power cords, covers, rubber parts, or peripherals other than the Product.
Where to Obtain Service :
At a Sharp Authorized Servicer located in the United States. To find out the location of the nearest Sharp Authorized
Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service :
Ship (prepaid) or carry in your Product to a Sharp Authorized Servicer. Be sure to have proof of purchase available. If
you ship or mail the Product, be sure it is packaged carefully.
PRODUCT SUPPORT
Registering a password
1. Press TEL or SCHEDULE/MEMO to display
“NAME?”, “SCHEDULE?”,
or “MEMO?”.
2. Press SECRET .
PASSWORD?
If the password is forgotten, you cannot delete the 3. Enter the password
(case sensitive), e.g. ABC.
password only. You have to delete all the memory
contents. (Perform steps 2 and 3 as described in 4. Press SECRET to register it.
• The display returns to the screen in step 1
the section, “Using the Organizer for the First
with the symbol “
”.
Time”.) As a safeguard, make a written record of
•
If
“ERROR!”
appears
briefly,
a password has
the password.
already been registered. Enter the correct
password or delete the password and all the
memory contents.
5. Press SECRET SECRET to turn Secret
function on. “
” disappears.
e00_el6900_65e.p65
2. Turning Secret function on and off
2. Press SECRET . “PASSWORD?” is displayed.
3. Enter the password and press SECRET .
•“
” is displayed and you can display
secret entries.
• If you enter an incorrect password,
“ERROR!” appears briefly. Follow the above
steps and enter the correct password.
• Even when Secret function is turned off, it
will be automatically turned on (“
” will
disappear):
A)when you press GAME , CLOCK , or
CALC/CONV ,
or B)after the power is turned off manually
or automatically.
LIMITED WARRANTY
Secret Function
1. Registering a password and storing
secret entries
Storing secret entries
1. Enter characters in Telephone, Schedule, or
Memo mode when “
” is not displayed
(Secret function is on).
• When “
” is displayed, press SECRET
SECRET to turn Secret function on.
2. Press SECRET before pressing ENTER to
store. “
” appears.
3. Press ENTER to store a secret entry in the
memory.
• “STORED!” appears briefly, and the display
returns to the mode screen without “
”
(Secret function is on).
• You cannot display the secret entry until you
turn Secret function off.
If you have read the ORGANIZER operation manual,
but you still require product support, you can:
Call a Sharp Customer Assistance Center
630-378-3590
(7am to 7pm CST M-F)
Visit our Web Site
http://www.sharpusa.com
Write to our Customer Assistance Center
Sharp Electronics Corp.
Customer Assistance Center
Att: WIZARD HELP
1300 Naperville Drive
Romeoville, IL 60446
Online Shopping (Purchase additional peripherals, etc.)
URL: www.sharpplace.com
Send an E-mail
pdasupport@sharpsec.com
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-1163.
6/4/2002, 10:23 AM