QMS 4060 Large-Capacity Input Feeder for Legal-size Media

Installation Guide
QMS® 4060
Large-Capacity Input Feeder for Legal-size Media (LCIF -Legal)
Caution:
However, if you do install this option yourself (or if you ever move the printer and this option), you must make
certain that the option aligns correctly with the printer.
We highly recommend that you have
an authorized QMS service techniThis document provides quick installation information for the large-capacity input feeder for legal-size media.
cian install your QMS 4060 as well as For complete information, refer to appendix C, “Installing Options,” in the Getting Started manual or chapter 6,
“Hardware Options,” in the Options manual (on the 4060 Print System Documentation CD-ROM).
the optional large-capacity input
feeder.
!
Installation of the LCIF-Legal may require a call to your authorized service provider. If the engine prom (EPROM) part is marked with #1001598D or a lower alpha
character, then an upgrade is required. If the EPROM is labelled #1001598E or higher, an upgrade is not necessary. Installation of the EPROM by a nonauthorized service organization or individual will void the warranty of the printer and the LCIF. In addition, this option also requires system code rv2.1.3.
Check the startup page; if the system code is not rv2.1.3 or higher, refer to chapter 9, “Troubleshooting,” in the QMS 4060 Print System Operation manual on your
QMS 4060 Print System Documentation CD-ROM to update the printer’s software. This enables the engine to recognize the Large-Capacity Input Feeder for legalsize media.
Installing the Large-Capacity Input Feeder (LCIF-Legal)
The Large-Capacity Input Feeder for legal-size media (LCIF-Legal) holds 3000 sheets and increases the paper input capacity of the QMS 4060 Print System to 4500
sheets. The LCIF-Legal supports only plain paper 17–24 lb (64–90 g/m²). Thick paper, greater than 24 lb (90 g/m²), prepunched, and predrilled paper are not recommended.
Caution: Proper alignment of the LCIF to the printer is extremely important. Improper alignment causes frequent media jams. A firm, level surface is
necessary to achieve alignment. If you are placing your printer and LCIF on a soft carpeted floor, be sure you place a firm material, such as a chair
mat, under the units for stability.
The depth of the LCIF-Legal is 17.6" (446 mm). The LCIF-Legal requires the following clearances when you are installing this option:
Item
Left side
Right side
Clearance
Printer attach side
37.4" (950 mm)
Item
Front
Rear
Clearance
25.6" (650 mm)
33.5" (850 mm)
Item
Height
Clearance
23.6" (600 mm)
For final positioning of the printer and LCIF-Legal, make sure to allow enough room for the door of the input feeder to open completely (without having to move the
unit). Unnecessary movement of the printer and feeder can cause misalignment between the two units, and jams occur as a result.
WARNING! The LCIF-Legal weighs approximately 41 lb. (18.6 kg). Do not attempt to lift or move it by yourself.
ACHTUNG! Der LCIF-Legal wiegt ca. 18.6 kg; bitte versuchen Sie niemals, das Gerät alleine anzuheben oder zu tragen.
Unpack all items from the
box.
1
Locate the support stand,
the support stand bracket,
and the sheet guide.
2
Save the packing material
for possible repacking.
Turn off the printer and
open the front door.
3
Attach the sheet guide to
the printer using the screws
you loosened and removed
earlier.
4
.....
......
Using a Phillips
screwdriver, remove the
right-side paper input cover
by loosening the front
screw and removing the
rear screw.
Install the support stand
bracket using the screws
attached.
Lift the support stand and
place it on top of the
support stand bracket.
5
6
Pull out the support stand
slide-rails until they lock in
the out position.
Attach the support stand to
the support stand bracket.
Set the LCIF on the pins of
the slide-rails.
Secure the LCIF to the
support stand using the
thumbscrews.
1760255-001A
1
QMS 4060 LCIF-Legal Installation Guide (continued)
Connect the interface cable
to the connector on the rear
lower-left side of the printer.
7
Caution: Adjust the
leveling feet on the
support stand so the
leveling chains just
touch the floor.
8
Slide the LCIF into the
sheet guide on the printer
until it locks in place.
Turn on the printer.
LTR
LTR
LTR
9
Check the printer display
panel for the LCIF graphic.
To load paper in the LCIFLegal, open the LCIF door,
press the button on top of
the LCIF, load paper, and
close the door.
10
This lets you know the
LCIF is connected properly.
LETTER
LETTER
LETTER
IDLE
Online
Tray
Cancel
Status
LTR
Press the Tray button on the
printer control panel to
select the LCIF-Legal for
paper feeding.
LTR
Copy
LTR
LTR
Use the Previous or Next
button to highlight the LCIFLegal on the graphic, and
then press Select.
LTR
LTR
LTR
11
Through the Administration/Engine/Default Paper Sz menu, set the LCIF-Legal to legal-size paper.
Online
Menu
Administration
Engine
Default Paper Sz.
Legal
For further menu information, see chapter 4, “Printer Configuration,” in the QMS 4060 Print System Reference manual on your QMS 4060 Print System Documentation CD-ROM.
The operating environment is the same as for the printer. For information about paper jams, see “Clearing LCIF Pick-up Jams” on page 4-6 of the QMS 4060 Print
System Operation manual on your QMS 4060 Print System Documentation CD-ROM.
QMS is a registered trademark of QMS, Inc.
Copyright © 1999 by QMS, Inc. All Rights Reserved.
2
Open as PDF
Similar pages
Xonar Essence STU
Essence 3
JVC LVT2015-001A User's Manual