BA Cover C450.qxd
21.06.2005
16:33 Uhr
Seite 1
s
Siemens Aktiengesellschaft,
issued by Siemens Communications
Haidenauplatz 1
D-81667 Munich
© Siemens AG 2005
All rights reserved. Subject to availability.
Rights of modification reserved.
Gigaset C450
Siemens Aktiengesellschaft
www.siemens.com/gigaset
cyan magenta yellow black
Liebreich Medienproduktion
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / overview.fm / 27.7.05
The handset at a glance
The handset at a glance
1 Display in idle status
2 Battery charge level
e V U (1/3 charged to fully charged)
= flashes: battery almost flat
e V U flashes: battery charging
3 Control key (page 10)
4 Display keys (page 10)
5 End call key, On/Off key
End call, cancel function, go back one menu level
(press briefly), back to idle status (press and hold),
activate/deactivate handset (press and hold in idle
status)
6 Message key
Opens calls and message lists
Flashes: new message or new call
7 Hash key
Keypad lock on/off (press and hold, page 10)
Toggle between upper/lower case letters and digits
for text entry (page 28)
8 Alarm clock key (page 22)
Activate and deactivate the alarm clock
9 Microphone
10 Recall key
Enter flash (press briefly)
Insert a pause (press and hold)
11 Star key
Ringtones on/off (press and hold in idle status),
12 Connection socket for headset (page 6)
13 Handsfree key
Switch between earpiece and handsfree mode
Lights up: handsfree activated
Flashes: incoming call
14 Talk key
Answer a call, open last number redial list (press
briefly), start dialling (press and hold)
15 Signal strength
¦ § ¨ (low to high)
¥ flashes: no reception
1
15
¨
V
11.11.05
§§§§§§INT§§§§§
11:56
§§§Menu§§
2
3
4
14
5
13
6
12
11
7
10
8
9
Base station at a glance
1
1 Paging key
1
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / C450_laender_IVZ.fm / 27.7.05
Contents
Contents
Using several handsets . . . . . . . . . . . 19
Base station at a glance . . . . . . . . . . . 1
Registering handsets . . . . . . . . . . . . . . . . .
Locating a handset ("Paging") . . . . . . . . . .
Making internal calls . . . . . . . . . . . . . . . . . .
Listening in to an external call . . . . . . . . . .
Safety precautions . . . . . . . . . . . . . . . 3
Handset settings . . . . . . . . . . . . . . . . 21
The handset at a glance . . . . . . . . . . . 1
Changing the display language . . . . . . . . .
Setting the display . . . . . . . . . . . . . . . . . . .
Activating/deactivating auto answer . . . . .
Adjusting the loudspeaker volume . . . . . . .
Changing ringtones . . . . . . . . . . . . . . . . . .
Activating/deactivating
suppression of the first ringtone . . . . . . . .
Advisory tones . . . . . . . . . . . . . . . . . . . . . .
Using the handset as an alarm clock . . . . .
Restoring the handset default settings . . .
Gigaset C450 –
more than just a telephone . . . . . . . . 4
First Steps . . . . . . . . . . . . . . . . . . . . . . 4
Pack contents . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the base station . . . . . . . . . . . . . . .
Connecting the base station . . . . . . . . . . . . .
Setting up the handset for use . . . . . . . . . . .
Belt clip and headset . . . . . . . . . . . . . . . . . . .
4
4
4
4
6
Menu tree . . . . . . . . . . . . . . . . . . . . . . 7
Operating the base station on
the PABX . . . . . . . . . . . . . . . . . . . . . . 23
Dialling modes and flash time . . . . . . . . . . 23
Setting pauses . . . . . . . . . . . . . . . . . . . . . . 24
Appendix . . . . . . . . . . . . . . . . . . . . . . 25
10
10
10
10
10
11
11
Symbols and typographical
conventions used . . . . . . . . . . . . . . . . . . . .
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact with liquid . . . . . . . . . . . . . . . . . .
Questions and answers . . . . . . . . . . . . . . .
Service (Customer Care) . . . . . . . . . . . . . . .
Authorisation . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . .
Writing and editing a text message . . . . . .
Using the directory and lists . . . . . . 12
Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Last number redial list . . . . . . . . . . . . . . . . . 13
Opening lists with the message key . . . . . . 13
25
25
25
25
26
27
27
28
Accessories . . . . . . . . . . . . . . . . . . . . 29
Index . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Making cost-effective calls . . . . . . . 14
Automatic network provider code
(preselection) . . . . . . . . . . . . . . . . . . . . . . . . 14
Displaying the call duration . . . . . . . . . . . . . 14
SMS (text messages) . . . . . . . . . . . . 15
Registering for SMS using the
registration wizard . . . . . . . . . . . . . . . . . . . .
Writing/sending an SMS . . . . . . . . . . . . . . .
Receiving an SMS . . . . . . . . . . . . . . . . . . . . .
Setting SMS centre: . . . . . . . . . . . . . . . . . . .
SMS to a PABX . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating the SMS function . .
SMS troubleshooting . . . . . . . . . . . . . . . . . .
22
22
22
23
Restoring the base station to
factory settings . . . . . . . . . . . . . . . . . . . . . . 23
9
9
9
9
9
Operating the handset . . . . . . . . . . . 10
Switching the handset on/off . . . . . . . . . . .
Activating/deactivating the keypad lock . . .
Control key on the handset . . . . . . . . . . . . .
Display keys . . . . . . . . . . . . . . . . . . . . . . . . .
Returning to idle status . . . . . . . . . . . . . . . .
Menu guidance . . . . . . . . . . . . . . . . . . . . . .
Correcting incorrect entries . . . . . . . . . . . . .
21
21
21
21
21
Base station settings . . . . . . . . . . . . 23
Making calls . . . . . . . . . . . . . . . . . . . . 9
Making an external call . . . . . . . . . . . . . . . . .
Ending a call . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call . . . . . . . . . . . . . . . . . . . . . . .
Calling Line Identification. . . . . . . . . . . . . . . .
Handsfree operation . . . . . . . . . . . . . . . . . . .
19
20
20
20
15
15
16
17
17
17
17
Using the network mailbox . . . . . . . 19
Configuring the network mailbox
for fast access . . . . . . . . . . . . . . . . . . . . . . . 19
Viewing a message from the
network mailbox . . . . . . . . . . . . . . . . . . . . . 19
2
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / security.fm / 27.7.05
Safety precautions
Safety precautions
Caution:
Read the safety precautions and the user guide before use.
Explain their contents to your children, and the potential hazards associated with using the telephone.
$
Only use the mains adapter supplied, as indicated on the underside of the base station.
Fit only the recommended rechargeable batteries (page 27) of the same type! I.e. do
not use any other battery type or non-rechargeable batteries as this could result in significant health risks and personal injury.
‹
Œ
Insert rechargeable batteries with the correct polarity, and use them according to this user
guide (polarity symbols can be seen in the handset's battery compartment, page 4).
The operation of medical appliances may be affected. Be aware of the technical conditions
in your particular environment, e.g. doctor's surgery.
The handset may cause an unpleasant humming noise in hearing aids.
Do not install the base station in bathrooms or shower rooms. The handset and base station are not splash proof (page 25).
Do not use the phone in environments with a potential explosionhazard, e.g. auto paint
shops.
ƒ
If you give your Gigaset to someone else, make sure you also give them the user guide.
Dispose of used devices and batteries in accordance with statutory requirements.
Note:
Not all of the functions described in this manual are available in all countries.
3
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / starting.fm / 27.7.05
Gigaset C450 – more than just a telephone
Gigaset C450 –
more than just a telephone
Connecting the base station
¤
Your phone not only enables you to send and
receive text messages over the fixed network
and store up to 100 telephone numbers
(page 12) – it can do a whole lot more:
u You can programme the keys of your phone
with important phone numbers. The
number is then dialled by simply pressing a
key (page 12).
u Use the handsfree function (page 9) to keep
your hands free when making a call.
u Use your handset as an alarm clock
(page 22).
First connect the mains adapter and then
the phone jack as shown below .
1
3
2
1 Mains adapter 230 V
2 Underside of the base
3 Phone jack with phone cord
Have fun using your new telephone!
Please remember:
First Steps
times for operation as the phone does not
work without mains connection.
u If you buy a replacement phone cord from a
store ensure that the phone jack is connected correctly.
u Keep the mains adapter plugged in at all
Pack contents
The pack contains:
u one Gigaset C450 base station
u one Gigaset C45 handset
u one mains adapter
u one phone cord
u two batteries
u one battery cover
u one belt clip
u one user guide
Setting up the handset for use
Installing the base station
Inserting the batteries
Correct phone jack assignment
The base is designed to be operated in
enclosed, dry areas at temperatures ranging
from +5 °C to +45 °C.
Set up the base station at a central point in
the apartment or house.
3
4
2
5
1
6
1
2
3
4
5
6
unused
unused
a
b
unused
unused
Caution:
Use only the rechargeable batteries recommended by
Siemens on page 27. I.e. never use a conventional
(non-rechargeable) battery or other battery type,
otherwise serious damage to health and property
cannot be ruled out, e.g. the outer casing of the batteries could be destroyed or the batteries could
explode. The phone could also malfunction or be
damaged as a result of using batteries that are not of
the recommended type.
¤
Please note:
u Never expose the telephone to heat sources,
direct sunlight, other electrical appliances.
u Protect your Gigaset from moisture, dust,
¤
corrosive liquids and vapours.
4
Fit the batteries with the correct polarity
(see diagram).
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / starting.fm / 27.7.05
First Steps
the display key §INT§ at the bottom left of the display.
The polarity is indicated in the battery compartment.
Notes:
–
–
–
The handset switches on automatically. You will
hear a confirmation tone.
Closing the battery cover
¤
Position the cover pointing slightly downwards and push it up until it clicks into position.
–
¤
Automatic registration is not possible when the
base station on which you wish to register the
handset is being used to make a call.
A key press cancels automatic registration.
If four handsets are already registered to the base
station there are two options:
– The handset with the internal number 4 is in
idle status: the handset you wish to register is
assigned the number 4. The handset that was
previously number 4 is de-registered.
– The handset with the internal number 4 is
being used: the handset you wish to register
cannot be registered.
If automatic registration does not work the handset will have to be registered manually (page 19).
To charge the batteries, leave the handset in
the charging cradle on the base station.
Notes:
–
–
Opening the battery cover
¤
The handset may only be placed in the base provided for it.
If the handset has switched itself off because the
batteries are flat and is then placed in the cradle,
it will switch itself on automatically.
For questions and problems see page 25.
Press below the upper curve on the battery
cover and slide down.
Initial charging and discharging of
batteries
Placing the handset in the base station
and registering
Battery charging is indicated in the top right of
the display by a flashing battery icon e, V
or U. During handset operation, the battery
icon indicates the charge status of the batteries
(page 1).
Important: the handset must not already be
registered to a base station.
Registering the handset to the Gigaset C450
base station occurs automatically.
Place the handset in the charging cradle of
the base unit with its display facing forward.
The correct charge status can only be displayed
when the batteries are first fully charged and
discharged through use.
To do this, leave the handset in the base
without interruption until the battery icon
stops flashing in the display (approx. 13h).
Once the batteries are fully charged, remove
the handset from the base and do not put it
back again until the batteries are fully discharged.
¤
¤
You will hear a confirmation tone.
¤
Automatic registration takes around one
minute. While registration is in progress the
screen displays Registering and Base flashes.
The handset is assigned the lowest unassigned
internal number (1–4). If several handsets are
registered to the base, the internal number is
shown in the display after registration, e.g. INT
2. This means that the handset has been
assigned the internal number 2. If the handset
has been registered successfully you will see
Note:
After the first battery charge and discharge you may
replace your handset in its base after every call.
Please remember:
u Always repeat the charging and discharging
procedure if you remove the batteries from
the handset and re-insert them.
5
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / starting.fm / 27.7.05
First Steps
u The batteries may warm up as they are
charging. This is not dangerous.
u After a time the charge capacity of the batteries will decrease for technical reasons.
Note:
You will find explanations for the symbols and typographical conventions used in this user guide in the
appendix, page 25.
Setting the date and time
§Menu§
~
~
¢ Settings ¢ Date/Time
Enter the day, month and year
with 6 digits and press §OK§. Use q
to move between the fields.
Enter hours and minutes with 4
digits (e.g. 0 7 1 5 for 07.15 hrs)
and press §OK§. Use q to move
between the fields.
Once the phone is registered and the time
set, the idle display looks as shown on
page 1.
Your phone is now ready for use.
Belt clip and headset
By using a belt clip and headset (optional) you
can easily make your mobile phone a constant
companion both inside the building and in its
immediate vicinity.
Attaching the belt clip
There are notches for attaching the belt clip on
the side of the handset at approximately the
same height as the display.
Press the belt clip onto the back of the handset so that the protrusions on the belt clip
engage with the notches.
¤
The belt clip's clasp must be pointing towards
the battery compartment.
Connection socket for headset
You can connect the following types of headset
(with jack connector): HAMA Plantronics M40,
MX100 and MX150.
6
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / menuetree.fm / 27.7.05
Menu tree
Menu tree
There are two ways to select a function:
Using number combinations ("shortcut")
¤
¤
¤
To open the main menu, press §Menu§ with the handset in idle status.
Enter the number combination that is in front of the function in the menu tree.
Example: §Menu§ 4 2 2 for "Set handset language".
Scrolling through the menus (see also page 25)
¤
¤
To open the main menu, press §Menu§ with the handset in idle status.
Scroll to the required function with the control key and press §OK§.
1
SMS
1-1
Write Message
1-2
Incoming 00+00
1-3
Outgoing
1-4
Settings
1-4-1
Service Centres
1-4-1-1 Service Centre 1
…
[to]
1-4-1-3 Service Centre 3
2
Alarm Clock
2-1
Activation
2-2
Wakeup time
3
Audio Settings
3-1
Ringer Volume
3-2
Ringer Melody
3-3
Advisory Tones
3-4
Battery Low
1-4-2
Register to Service Centres
3-2-1
External Calls
3-2-2
Internal Calls
3-2-3
Alarm Clock
3-4-1
Off
3-4-2
On
3-43
During Call
7
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / menuetree.fm / 27.7.05
Menu tree
4
Settings
4-1
Date/Time
42
Handset
4-2-1
Display
4-2-1-1 Screensaver
4-2-1-2 Colour Scheme
4-2-1-3 Contrast
4-2-1-4 Backlight
4-3
Base
4-2-2
Language
4-2-3
Auto Answer
4-2-4
Register Handset
4-2-5
Reset Handset
4-3-2
System PIN
4-3-3
Base Reset
4-3-4
Listening in
4-3-5
Preselection
4-3-5-1 Preselection Number
4-3-5-2 With Preselection
4-3-5-3 Without Preselection
5
Voice Mail
5-1
Set Key 1
5-1-1
Network Mailbox
8
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / telephony.fm / 27.7.05
Making calls
Making calls
– CLIP (Calling Line Identification Presentation): the caller's number is displayed
u You have arranged CLIP with your network
provider.
u The caller has arranged CLI with the network
provider.
Making an external call
External calls are calls using the public telephone network.
~c
Or:
c~
Call display with CLIP/CLI
Enter the number and press the
talk key.
If the caller's number is stored in your directory,
you will see their name.
Press and hold the talk key c and
then enter the number.
You can cancel the dialling operation with the
end call key a.
–
–
Dialling with the directory (page 12) or last
number redial list (page 13) saves repeated keying of phone numbers.
You can assign a number from the directory to a
key for speed dialling (page 12).
You can edit or add to any phone number selected
by means of quick dialling or from the directory
and use it for the current call.
1234567890
2
The following is displayed in place of the
number:
u External Call, if no number is transmitted.
u Withheld, if the caller has withheld Calling
Line Identification.
u Unavailable , if the caller has not arranged
Calling Line Identification.
Ending a call
a
1
§Menu
1 Ring icon
2 Number or name of caller
Notes:
–
®
Handsfree operation
Press the end call key.
In handsfree mode, instead of holding the
handset to your ear you can put it down e.g. on
the table in front of you to allow others to participate in the call.
Answering a call
The handset indicates an incoming call in three
ways: by ringing, by a display on the screen,
and by the flashing handsfree key d.
Activating/deactivating handsfree
You can accept the call by:
Pressing the talk key c.
Pressing the handsfree key d.
Activating while dialling
~d
Enter the number and press the
¤
¤
¤
If the handset is in the base and the Auto Answer
function is activated (page 21), the handset will
take a call automatically when you lift it out of
the base.
handsfree key.
You should inform your caller before you use
the handsfree function so that they know
someone else is listening.
Switching between earpiece and handsfree
mode
d
Press the handsfree key.
If the ringtone is intrusive, press §Menu§ Silent .
You can take the call so long as it is displayed on
the screen.
Switch handsfree on and off during a call .
Calling Line Identification.
If you wish to place the handset in the base station during a call:
Press and hold the handsfree key d while
placing the handset in the base station. If
handsfree key d does not light up, press the
key again.
¤
When you receive a call, the caller's number is
displayed on the screen if the following conditions are met:
u Your network provider supports CLIP, CLI:
– CLI (Calling Line Identity): the caller's
number is transmitted
For how to adjust the volume, see page 21.
9
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / telephony.fm / 27.7.05
Operating the handset
Operating the handset
During an external call
s
Open the directory.
t
Adjust loudspeaker volume for
Switching the handset on/off
a
earpiece and handsfree mode.
Press the end call key long.
Display keys
You will hear the confirmation tone.
The current display functions are shown in the
bottom display line in reversed highlights. The
function of the display keys changes depending
on the particular operating situation.
Activating/deactivating the keypad
lock
#
Example:
Press and hold the hash key.
§§§§INT§§§
You will hear the confirmation tone. The icon
Ø appears in the display when the keypad lock
§§Menu
is activated.
1
2
The keypad lock deactivates automatically
when you receive a call and activates again
after the call.
Note:
1 Current display key functions
2 Display keys
The handset displays an advisory message if you
press a key by accident while the keypad lock is on. To
deactivate the keypad lock, press the hash key #
and hold.
The most important display symbols are:
§Back§
Control key on the handset
Go back one menu level or cancel
operation.
§INT§
Make an internal call (page 20).
§Menu§
Open the main menu or a contextdependent menu.
§§§§INT§§§
§§Menu
1
§OK§
Confirm highlighted selection.
§<C§
Delete key: backspace delete one
character at a time.
Returning to idle status
1 Control key
You wish to return to idle status from anywhere
in the menu:
Press the end call key a and hold.
In this user guide, the side of the control key
that you must press in the given operating
situation is shown in black (top, bottom). Example: t for "press the top of the control key".
¤
Or:
¤
The control key has a number of different functions:
Do not press any key: after 2 minutes the display will automatically revert to idle status.
Changes which you have not confirmed/stored
by pressing §OK§ will be rejected.
When the handset is in idle status
Open the directory.
s
t
Adjust the ringer melody volume
For an example of the display in idle status,
page 1.
of the handset (page 21).
In lists and menus
Scroll up/down line by line.
t/s
In an input field
Move the cursor left or right.
t/s
10
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / telephony.fm / 27.7.05
Operating the handset
Menu guidance
Your telephone's functions are accessed using a
menu that has a number of levels.
Main menu (first menu level)
¤
To open the main menu, press §Menu§ with the
handset in idle status.
Accessing a function
¤
Scroll to the function with the control key q
and press §OK§.
Or:
¤
Enter the number that is in front of the function in the menu tree (page 7).
The corresponding submenu (the next menu
level) is opened.
Submenus
The functions in the submenus are displayed as
lists.
To access a function:
Scroll to the function with the control key q
and press §OK§.
¤
Or:
¤
Enter the number combination that is in
front of the function in the menu tree
(page 7).
A short press on the end call key a returns you
to the previous menu level / cancels the operation.
Correcting incorrect entries
u Navigate to the wrong input with the control
key if T is displayed.
u Press §<C§ to delete the character to the left of
the cursor.
u Insert new character to the left of the cursor.
u When entering the time and date etc., edit
the flashing character.
You will find explanations for the symbols and
typographical conventions used in this user
guide in the appendix, page 25.
11
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / directories_charges.fm / 27.7.05
Using the directory and lists
Using the directory and lists
Managing directory entries
You have selected an entry (page 12).
The options are:
u Directory
u Last number redial list
u SMS list
u Calls list
Editing entries
§Menu§
~
¢ Edit Entry
Edit the number if required, and
press §OK§.
You can save 100 entries in the directory.
~
You can create a personalised directory for your
own individual handset. However you can send
the list or individual entries to other handsets
(page 12).
Using other functions
s ¢ s (select entry; page 12) ¢ §Menu§
The following functions can be selected with
q:
Directory
Use Number
Edit or add to a stored number. Then dial or
use other functions with §Menu§.
You can store numbers and the associated
names in the directory.
With the handset in idle status, open the
directory by pressing the s key.
¤
Delete Entry
Delete selected entry.
Send Entry
Send a single entry to another handset
(page 12).
Length of an entry
Number:
Name:
max. 32 digits
max. 16 characters
Delete List
Delete all directory entries.
Note:
You can assign a number from the directory to a key
for speed dialling (page 12).
Send List
Send the complete list to another handset
(page 12).
Storing the first number in the directory
Shortcut
Assign to the current entry for speed dialling
to a selected key.
s ¢ §OK§ ¢ Directory empty New Entry?
~
Enter number and press §OK§.
~
Enter the name and press §OK§.
Using quick dial keys
¤
Storing a number in the directory
s ¢ §Menu§ ¢ New Entry
~
Enter number and press §OK§.
~
Enter the name and press §OK§.
Press and hold the required quick dial key.
Sending the directory to another handset
Requirements:
u The sending and receiving handsets must
both be registered to the same base station.
Selecting a directory entry
s
Edit the name if required, and
press §OK§.
u The other handset and base station can send
Open the directory.
and receive directory entries.
s ¢ q (select entry; page 12) ¢ §Menu§
You have the following options:
u Use q to scroll to the entry until the
required name is selected.
u Enter the first character of the name, or
scroll to the entry with q.
¢ Send Entry
~
/ Send List
Enter the internal number of the
receiving handset and press §OK§.
A successful transfer is confirmed by a message
and confirmation tone on the receiving handset.
Dialling with the directory
s ¢ q (select entry; page 12)
c
Press the talk key. The number is
If you have sent a single entry, you can transfer
another entry with §OK§.
dialled.
12
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / directories_charges.fm / 27.7.05
Using the directory and lists
Please remember:
Delete Entry (as in the directory, page 12)
u Entries with identical numbers are not over-
Delete List (as in the directory, page 12)
written in the receiving handset.
u The transfer is cancelled if the phone rings
or if the memory of the receiving handset is
full.
Opening lists with the message key
You can use the message key f to open the following lists:
u SMS list
u Network mailbox
If your network provider supports this function and the network mailbox is configured
for fast access (page 19).
u Calls list
Adding a displayed number to the
directory
You can copy to the directory any numbers that
appear in a list, e.g. the calls list or the last
number redial list.
A number is displayed.
¤
¢
Copy to Directory
Complete the entry (page 12).
§Menu§
An advisory tone sounds as soon as a new
entry appears on a list. The key f flashes. A
message appears in the display.
Copying a number from the directory
When you press the flashing key f, you will
see all the lists that contain new messages. If
only one list contains new messages, this will
be opened automatically.
You can open the directory in many operating
situations e.g. to transfer a number. Your handset need not be in idle status.
s
q
Note:
Open the directory.
If calls are stored in the network mailbox you will
receive a message if the appropriate settings have
been made (see the network mailbox instructions of
your network provider).
Select entry (page 12).
Last number redial list
The last number redial list contains the ten
numbers last dialled with the handset (max. 32
numbers). If one of the numbers is in the directory, then the corresponding name will be displayed.
Calls list
Requirement: CLIP (page 9)
The numbers of the last 10 missed calls are
stored. Multiple calls from the same number
are only stored once (the last call).
Dialling from the last number redial list
c
q
c
The calls list is displayed as follows:
Press the key briefly.
Calls List: 01+02
Select an entry.
Press the talk key again. The
number is dialled.
Number of new entries + number of old, read entries
Opening callslist
Managing entries in the last number redial
list
c
q
Press the key briefly.
§Menu§
Press the display key.
f ¢ Calls List: 01+02
q
Select entry.
The last incoming call is displayed in the calls
list.
Select an entry.
List entry
The following functions can be selected with
q:
Example of a list entry:
Use Number (as in the directory, page 12)
Copy to Directory
Copy an entry to the directory (page 13).
New Call
1234567890
11.11.05
§Back§
13
U
01/02
19:27
§Menu
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / directories_charges.fm / 27.7.05
Making cost-effective calls
u Status of entry
Storing preselection numbers
¢ Settings ¢ Base ¢ Preselection
¢ Preselection Number
In the calls list
New Call: new missed call.
Old Call: entry already read.
Call recv.: call taken.
u Entry number
01/02 means e.g.: first of a total of two
entries.
u Number or name of caller
You can add the number of the caller to the
directory (page 13).
u Call date and time (if set, page 6).
§Menu§
~
Enter or edit preselection number
(call-by-call number).
§OK§
Press the display key. The entry is
stored.
a
Press and hold (idle status).
Saving or editing entries in the
preselection lists
Each of the two lists can contain 11 entries with
4 digits.
You can delete the current entry with
§Menu§ Delete Entry .
Numbers may be prefixed according to the
country in the "with preselection" list. This
means, for example, that all national calls or
calls to the mobile network are automatically
linked to the preselection number you have
stored previously.
Deleting the calls list
Caution! All old and new entries will be
deleted.
f ¢ Calls List: ¢ §Menu§ ¢ Delete List
a
Press and hold (idle status).
¢ Settings ¢ Base ¢ Preselection
¢ With Preselection / Without Preselection
§Menu§
Making cost-effective calls
Make your calls via a network provider who
offers very low call charges (call-by-call), have
the call duration displayed on your handset
after the call. You can store and manage several
call-by-call numbers.
q
~
Select entry and press §OK§.
§OK§
Press the display key. The entry is
stored.
Enter or edit first digits of number.
a
Press and hold (idle status).
Temporarily cancelling preselection
c (press and hold) ¢ §Menu§ ¢ Automatic
Automatic network provider code
(preselection)
Preselect off
Permanently deactivating preselection
¤
You can specify a call-by-call number (preselection number) which is automatically placed in
front of certain numbers according to two lists
when you dial them.
u The list "with preselection" contains the
"rule" for dialling code numbers or the first
digits of dialling code numbers with which
you wish the preselection number to be
used.
u The list "without preselection" contains the
"exception to the rule".
Delete the preselection number with §<C§ and
press §OK§.
Displaying the call duration
The duration of a call is displayed
u during the conversation,
u until about three seconds after the call has
ended if you do not replace the handset in
the charging cradle.
Note:
Example:
The actual duration of the call can vary from that
shown by a few seconds.
You have entered 08 for "with preselection".
Now all numbers that start with 08 will be
dialled with preselection.
However, if you want, for example, that 081 is
still dialled without preselection, enter 081 for
"without preselection".
14
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / sms_neutral.fm / 27.7.05
SMS (text messages)
SMS (text messages)
have entered. You can also use the registration
wizard to register with SMS centres at a later
time.
Your unit is supplied ready for you to send text
messages immediately.
§Menu§
Requirements:
§Menu§
enabled for your phone connection.
u Your network provider supports SMS in the
fixed network (information on this can be
obtained from your network provider).
u You are registered with your service provider
to send and receive SMS.
§OK§
¢ SMS (on 1st. call)
¢ SMS ¢ Register to Service Centres
(later)
u Calling Line Identification (CLIP, page 9) is
Press the display key to confirm
the prompt.
You can now receive text messages from any of
the SMS centres whose number you have
entered (page 17).
Writing/sending an SMS
Text messages are exchanged between SMS
centres that are operated by service providers.
You must enter the SMS centre in the unit
through which you wish to send and receive.
You can receive SMS from every SMS centre
that is entered if you have registered with your
service provider. The registration wizard
(page 15) will help you to register.
An SMS may contain up to 160 characters.
Writing/sending an SMS
§Menu§
~
¢ SMS ¢ Write Message
Write an SMS. For how to enter the
text, see page 28.
§Menu§ Send Text
Your text message is sent through the SMS centre that is active (page 17). Only one SMS centre can be active at any one time.
s/~
If no SMS centre is entered, the SMS menu only
consists of the entry Settings . Enter an SMS centre (page 17).
Please remember:
u If your phone is connected to a PABX, please
read page 17.
u You must be registered with your service
Select and press §OK§.
Enter the number with prefix
(including your local area code)
from the directory or key it in manually, and press §OK§.
For SMS to an SMS mailbox: put
the mailbox ID at the end of the
number.
The SMS is sent.
Note:
provider to receive SMS text messages.
u Each incoming SMS is signalled by a single
ring (ringtone as for external calls). If you
accept such an SMS call on the first ring, the
SMS will be lost. To prevent this, suppress
the first ringtone for all external calls
(page 22).
If you are interrupted by an external call while writing
an SMS, the text is automatically saved in the draft
message list.
Draft message list
In the draft message list, you can save, edit later
and send an SMS.
Registering for SMS using the
registration wizard
Saving an SMS in the draft message list
You are writing an SMS (page 15).
§Menu§
You can use the registration wizard to register
with all service providers whose number you
have entered to send and receive SMS messages.
¢ Save Text
Opening the draft message list
§Menu§
¢ SMS ¢ Outgoing
The first entry in the list is displayed, e.g.:
Precondition:
u You must have stored a number for at least
one SMS centre.
Saved
01/02
11.11.05
19:27
§Back§
U
§Menu
01/02: Current number/total number of SMS text messages
When you call up the SMS menu for the first
time, the wizard automatically registers you
with accessible SMS centres whose number you
15
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / sms_neutral.fm / 27.7.05
SMS (text messages)
u messages that could not be sent on account
Reading or deleting individual SMS messages
¤
q
of an error.
Open the draft message list.
New text messages are signalled on all Gigaset
C45 handsets by a message in the display, the
flashing message key f and an advisory tone.
Select SMS.
§Menu§ Read SMS
Select and press §OK§ to read the
message. Scroll in the SMS using
q.
Opening the incoming message list with the f
key
f
Press.
Or:
§Menu§ Delete Entry
The incoming message list is displayed as follows (example):
Select and press §OK§ to delete the
message.
SMS:
Writing/editing an SMS
You are reading an SMS in the draft message
list.
§Menu§
01+05: The number of new + the number of old, read
messages
Press the display key.
An entry in the list is displayed e.g as follows:
You have the following options:
Write Message
Write and then send a new SMS (page 15) or
save.
New
1234567890
11.11.05
§Back§
U
Open the draft message list.
§Menu§
§Menu§ Delete List
¢ SMS ¢ Incoming
01+05
Reading or deleting individual SMS messages
Select and press §OK§.
a
19:27
Opening the incoming message list via the SMS
menu
Deleting draft message list
§OK§
01/02
§Menu
01/02: Current Number of the SMS currently in the display / total number of new SMS messages
Use text
Edit the text of the saved SMS and then send
(page 15).
¤
01+05
¤
¤
Press the display key to confirm
the delete. The list is cleared.
Press and hold (idle status).
Open the incoming message list.
Continue as described at "Reading or deleting individual SMS messages", page 16.
A new message which you have read acquires
the status Old.
Receiving an SMS
Deleting incoming message list
All received text messages are saved in the
incoming message list. Linked text messages
are displayed as one message. If this is too long
or has not transferred completely, it will be split
into individual messages. Since an SMS remains
in the list even after it has been read, you
should regularly delete SMS messages from
the list.
All new and old SMS in the list are deleted.
Open the incoming message list.
¤
Press the display key.
Continue as described for "Deleting draft
message list", page 16.
§Menu§
¤
Replying to or forwarding text messages
The display tells you if the message memory is
full.
Deleting text messages you no longer
require (page 16).
You are reading an SMS (page 16).
¤
§Menu§
Press the display key.
You have the following options:
Reply
Write and send a reply SMS directly
(page 15).
Incoming list
The incoming message list contains:
u all received SMS messages, starting with the
latest.
Use text
Edit the text in the SMS and then send it
(page 15).
16
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / sms_neutral.fm / 27.7.05
SMS (text messages)
Send
Forward the text of an SMS to another recipient (page 15).
SMS to a PABX
Adding a number to the directory
ing Line Identification (page 9) is forwarded to the extension of the PABX (CLIP).
The CLIP of the phone number for the SMS
centre is evaluated in your Gigaset.
u Depending on your PABX, you may have to
add the access code (external line prefix)
before the number of the SMS centre.
If in doubt, test your PABX e.g. by sending an
SMS to your own phone number, once with
and once without the access code.
u When you send SMS messages, your sender
number may be sent without your extension
number. In this case the recipient cannot
reply to you directly.
u You can only receive an SMS when the Call-
Adding the sender's number
You are reading an SMS in the incoming message list.
Press the display key.
§Menu§
Continue see page 13.
Note:
You can create a special directory for text messages
within your main directory by putting a star (*) before
the names.
An appended mailbox ID will be copied to the directory.
Sending and receiving SMS on ISDN PABXs is
only possible via the MSN number assigned to
your base station.
Setting SMS centre:
Activating/deactivating the SMS
function
Entering/changing SMS centres
¤
You should find out about the services and
special functions offered by your service
provider before you make a new application and before you delete preconfigured
phone numbers.
§Menu§
q
When you switch off you cannot send or receive
any SMS with your phone.
¢ SMS ¢ Settings ¢ Service Centres
Settings which you have made for sending and
receiving text messages (the numbers of SMS
centres) and any entries in the incoming message and draft message lists will be retained
even after the function is deactivated.
SMS centre (e.g. select Service
Centre 1) and press §OK§.
You have the following options:
§Menu§ 4 I O 2 L
~ Q §OK§
Deactivate the SMS function.
Active Send Serv. Centre
If the SMS messages are to be sent through
this SMS centre, press §OK§ to activate the
SMS centre (‰ = on). If a different SMS centre was active previously, then this will be
deactivated.
Or:
~ 1 §OK§
SMS Centre No.
Enter the number of the SMS centre and
press §OK§.
SMS troubleshooting
Errors when sending
Sending an SMS through another SMS
centre
¤
¤
Activate the SMS function (default
settings).
If an SMS cannot be sent for a longer period of
time, it is moved to the incoming message list
and given the status Error XX.
Activate the SMS centre (2 or 3) as the active
send service centre (page 17).
Send the SMS.
E0 Calling Line Identification permanently withheld
(CLIR) or Calling Line Identification not activated.
FE Error occurred during SMS transfer.
FD Connection to SMS centre failed, see self-help.
17
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / sms_neutral.fm / 27.7.05
SMS (text messages)
Self-help with errors
Messages are only received as voice messages during
the day.
The following table lists error situations and
possible causes and provides notes on troubleshooting.
The terminal is stored in your SMS provider's database as having no fixed network SMS functionality, i.e. you are no longer registered with the provider.
Register your terminal (again) for SMS reception (page 15).
You cannot send messages.
¥
1. You have not requested the CLIP service (Calling
Line Identification Presentation, page 9).
Ask your service provider to enable this service.
¥
You cannot access the SMS functions on your handset.
2. Text message transmission has been interrupted
(e.g. by a call).
Re-send the text message.
Another handset that is registered at the same
base station is currently using the SMS functions.
Wait until there is no other handset using the
SMS functions.
¥
¥
3. Network provider does not support this feature.
4. No number or an invalid number is entered for the
SMS centre activated as the send centre.
Enter phone number (page 17).
¥
You receive a message whose text is incomplete.
1. Your phone memory is full.
Delete old messages (page 16).
¥
2. The service provider has not yet sent the rest of
the message.
The message is played back.
1. The "display call number" service is not activated.
Ask your service provider to activate this function (chargeable).
¥
2. Mobile phone operator and network SMS service
provider have not agreed on a cooperation.
Obtain information from your network SMS
service provider.
¥
3. Your terminal is recorded in the records of your
SMS provider as having no fixed network SMS
functionality, i.e. you are no longer registered with
the provider.
Register your terminal (again) for SMS reception (page 15).
¥
18
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / T-NetBox_SAG-registration.fm / 27.7.05
Using the network mailbox
Using the network mailbox
Using several handsets
The network mailbox is your network provider's
answering machine. You cannot use the network mailbox unless you have applied to your
network provider.
Registering handsets
You can register up to four handsets on your
base station.
Configuring the network mailbox
for fast access
Automatic registration Gigaset C45 to Gigaset
C450, see page 5.
Manual registration Gigaset C45 to
Gigaset C450
With fast access, you can direct dial the network
mailbox.
The network mailbox is preconfigured for fast
access. You only need to enter the network
mailbox number.
You must activate manual registration of the
handset at both the handset and the base station.
Configuring the network mailbox for fast
access and entering the network mailbox
number
After it has registered, the handset returns to
idle status. If several handsets are registered to
the base, the internal number is shown in the
display after registration, e.g. INT 2.
§Menu§
¢ Voice Mail ¢ Set Key 1
The registration process is cancelled after
60 seconds. If the handset has not registered
within this time, repeat the process.
Network Mailbox
Select and press §OK§ (‰ = on).
~
a
Enter the network mailbox
number and press §OK§.
The entry is stored.
On the handset
Press and hold (idle status).
~
Menu§
This setting is now valid for all registered handsets.
Calling the network mailbox
1
Press and hold. This connects you
d
¢ Settings ¢ Handset ¢ Register
Handset
Enter the system PIN of the base
station (the default is 0000) and
press §OK§. Base is flashing in the
display.
On the base station
Press and hold the registration/
÷
directly to the network mailbox.
Press handsfree key d if required.
You hear the network mailbox
announcement.
paging key on the base station
(page 1) (min. 1 sec.).
Registering other handsets
Viewing a message from the
network mailbox
You can register other Gigaset handsets and
handsets for other devices with GAP functionality as follows.
On the handset
When a message arrives for you, you get a call
from the network mailbox. If you have
requested Calling Line Identification, the display shows the network mailbox number. If you
accept the call, the new messages are played
back. If you do not accept the call, the network
mailbox number will be stored in the list of
missed calls and the message key flashes
(page 13).
¤
Start to register the handset as described in
its user guide.
On the base station
÷
Press and hold the registration/
paging key on the base station
(page 1) (min. 1 sec.).
19
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / T-NetBox_SAG-registration.fm / 27.7.05
Using several handsets
Locating a handset ("Paging")
Ending an enquiry call
You can locate your handset using the base station.
Press the registration/paging key on the
base station (page 1) briefly.
All handsets will ring at the same time ("paging"), even if the ringers are switched off.
You are reconnected with the external caller.
¤
Accepting a waiting call
¤
If you get an external call while conducting an
internal call, you will hear the call waiting tone
(short tone). The caller's number will appear in
the display if phone number identification is
enabled.
Ending paging
÷/c
Briefly press the registration/pag-
a
ing key on the base station
(page 1) or press the talk key on
the handset.
You are conducting an external call. An internal
caller can listen in on this call and take part in
the conversation. All the participants are made
aware of the 'listening in' by a signal tone.
Calling other handsets
Press the display key. All handsets
are called.
Requirement: The Listening in function must
be activated.
Ending a call
a
Press the end call key.
Activating/deactivating internal listening
in
Transferring a call to another handset
a
Press the display key. All handsets
are called.
The external caller hears the hold
music.
Press and hold (idle status).
The line is engaged with an external call. Your
screen will display information to that effect
You want to listen in to the existing external
call.
Press the end call key.
c
The call is transferred. If the internal party does
not answer, or their phone is in use, the call will
automatically return to you.
Press and hold the talk key.
You are linked into the call. All participants hear
a signal tone.
Ending listening in
Press the end call key.
a
Internal consultation calls
When you are speaking to an external participant you can simultaneously call an internal
participant for consultation.
§INT§
¢ Base ¢ Listening in
Internal listening in
When an internal party answers:
If necessary announce the external call.
a
¢
Settings
(‰ = on)
Menu§
You can transfer an external call to another
handset (connect).
¤
Press the talk key to take the external call.
Listening in to an external call
Internal calls to other handsets registered on
the same base station are free.
§INT§
Press the end call key to end the
internal call.
c
Making internal calls
§INT§
Press the display key.
§Back§
All participants hear a signal tone.
If the first internal participant presses the end
call key a, the handset that has 'listened in'
remains connected to the external caller.
Press the display key. All handsets
are called.
The external caller hears the hold
music.
When an internal party answers you can speak
to them.
20
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / settings_bs_hs_pabx.fm / 27.7.05
Handset settings
Handset settings
Activating/deactivating auto
answer
Your handset is preconfigured, but you can
change these settings to suit your individual
requirements.
When this function is activated, when a call
arrives you can simply lift the handset out of
the base without having to press the talk key c.
Changing the display language
§Menu§
§Menu§
¢ Settings ¢ Handset ¢ Language
a
The current language is indicated by ‰ .
q
a
Press and hold (idle status).
q
Press keys one after the other.
You are conducting an external call.
Select the correct language and
press §OK§.
t
q
Setting the display
Press the control key.
Adjust the volume and press §OK§.
Note:
The handsfree volume can only be adjusted when
this function is set.
You have a choice of four colour schemes and
several different contrasts. You can also set a
screensaver and the illumination.
§Menu§
Press and hold (idle status).
You can set the loudspeaker volume for handsfree talking to five different levels and the earpiece volume to three different levels. You can
only adjust the loudspeaker volume during a
call.
If you accidentally choose a language you do
not understand:
422
Select and press §OK§ (‰ = on).
Adjusting the loudspeaker volume
Select a language and press §OK§.
§Menu§
¢ Settings ¢ Handset
Auto Answer
You can view the display texts in different languages.
Changing ringtones
¢ Settings ¢ Handset ¢ Display
u Volume:
You have the following options:
Five volume levels (1–5; e.g. volume 2 =
ˆ) and "crescendo" ring (6; volume
increases with each ring = ‰ ).
u Melody:
List of pre-loaded ringer melodies. The first
three melodies are the "classical" ring tones.
Screensaver
There are four different screensavers and
the settings No Screensaver or Digital Clock .
Colour Scheme
Four colour schemes. When the illumination
is switched off the display is shown in black
and white regardless of the selected setting.
You can also set different melodies for the following functions:
u External Calls : For external calls
u Internal Calls : For internal calls
u Alarm Clock : For the alarm clock
Contrast
Backlight
In Charger / Without Charger . Determines
whether the illumination stays on permanently or is switched off after a certain time
(‰ = permanently switched on).
Setting ringer volume
Note:
The ringer volume is the same for all types of
ring.
If the illumination is switched on outside the
charging cradle, the standby time for the handset
is considerably reduced!
§Menu§
¢ Audio Settings ¢ Ringer Volume
Or in idle status:
t
Press briefly.
Then:
q
a
21
Adjust the volume and press §OK§.
Press and hold (idle status).
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / settings_bs_hs_pabx.fm / 27.7.05
Handset settings
Setting ringer melody
– Confirmation tone (rising tone
sequence): at the end of an entry/setting, when the handset is placed in the
base station and on arrival of an SMS or
a new entry in the calls list.
– Error tone (descending tone sequence):
when you make an incorrect entry.
– Menu end tone: when scrolling at the
end of a menu.
u Battery warning tone: the battery requires
charging.
Set different ringer melodies for external calls,
internal calls and the alarm clock.
§Menu§
¢ Audio Settings ¢ Ringer Melody
External Calls / Internal Calls / Alarm Clock
Select and press §OK§.
q
a
Select melody (‰ = on) and press
§OK§.
Press and hold (idle status).
Activating/deactivating the ringer
You cannot deactivate the confirmation tone
for placing the handset in the base station.
You can turn off the ringer on your handset
before you take a call or while the phone is in
the idle state. You can take a call so long as it is
displayed on the screen.
Activating/deactivating advisory tones
§Menu§
Deactivating the ringer
Press the star key and hold, until
P
the Ú icon appears in the display.
§Menu§
Activating/deactivating
suppression of the first ringtone
Using the handset as an alarm
clock
The phone identifies an incoming SMS from the
first network signal.
25
Activating/deactivating the alarm clock
First ring muted.
§Menu§
Or:
~ Q §OK§
¢ Audio Settings ¢ Battery Low
On / Off / During Call
Select and press §OK§ (‰ = on). The
battery warning tone is activated
or deactivated or sounds during a
call.
status.
~ 1 §OK§
Select and press §OK§ (‰ = on).
Setting the battery warning tone
Re-activating the ringer
Press and hold the star key in idle
P
§Menu§ 4 I O
¢ Audio Settings ¢ Advisory Tones
Or:
First ring audible.
g
Please remember:
¢ Alarm Clock ¢ Activation (‰ = on)
Press the alarm clock key.
After you activate the alarm clock, the menu for
setting the wake up time opens automatically
(page 22).
If first ringtone muting is deactivated, then
every incoming SMS will be signalled by a ringtone. If you take this type of "call" at the first
ringtone, you will lose the SMS.
If the alarm clock is set, the wake up time
appears with the l icon in the display instead
of the date.
Advisory tones
Setting the wake up time.
Your handset uses ‘advisory tones’ to tell you
about different activities and statuses. The following tones can be activated and deactivated
independently of each other:
u Advisory tones:
– Key click: Each key press is acknowledged.
§Menu§
~
22
¢ Alarm Clock ¢ Wakeup time
Enter the wake up time in hours
and minutes, then press §OK§.
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / settings_bs_hs_pabx.fm / 27.7.05
Base station settings
When the alarm clock rings…
Resetting the base station using the menu
Alarm repeat after 5 minutes
§Menu§
§Snooze§
Press the display key or any key.
If you press §Snooze§ three times the alarm clock
switches off for 24 hours.
¤
Press the display key.
÷
Restoring the handset default
settings
¤
÷
You can reset any individual settings and
changes that you have made. This will not
affect entries in the directory, calls list, or SMS
lists or the handset's registration to the base
station.
§Menu§
§OK§
a
Press the display key to confirm.
Resetting the base station using a key on
the base station
Switching off the alarm clock for 24 hours
§Off§
¢ Settings ¢ Base ¢ Base Reset
§OK§
¤
¢ Settings ¢ Handset ¢ Reset Handset
Remove the base station mains adapter
(page 4) from the power socket.
Press the registration/paging key
(page 1)and hold down.
Replug the mains unit into your power
socket.
Continue to press the registration/
paging key (page 1).
Release the registration/paging key
(page 1). The base station has now been
reset.
Operating the base station on
the PABX
Press the display key to confirm.
Press and hold (idle status).
Cancel the reset with a.
Base station settings
The following settings are only needed when
your PABX requires them. Please refer to the
user guide for your PABX.
The base station settings are carried out using a
registered Gigaset C45 handset.
You cannot send or receive SMS messages on
PABXs that do not support Calling Line Identification.
Changing the system PIN
Dialling modes and flash time
You have to enter the system PIN when registering a handset to the base station.
Changing the dialling mode
You can change the base's 4-digit default system PIN ("0000") to a 4-digit PIN known only to
yourself.
§Menu§
~
a
You can set the dialling mode.
§Menu§ 4 I O 1 1
~ 1 §OK§
Pulse dialling mode (DP).
¢ Settings ¢ Base ¢ System PIN
Enter your new system PIN and
press §OK§. For security the PIN is
shown as four stars (****).
Press and hold (idle status).
Or:
~ Q §OK§
a
Touch tone dialling (DTMF).
Press and hold (idle status).
Restoring the base station to
factory settings
Setting the flash time
When the settings are restored all handsets are
de-registered. Each individual setting is
restored. Only the date and time are retained.
~
You can set the flash time.
§Menu§ 4 I O
12
Enter digits for the flash time and
press §OK§.
Q = 80 ms; 1 = 100 ms; 2 = 120 ms;
3 = 180 ms; 4 = 250 ms; 5 = 300 ms;
L = 600 ms; M = 800 ms
a
Press and hold (idle status).
23
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / settings_bs_hs_pabx.fm / 27.7.05
Operating the base station on the PABX
Setting pauses
Changing pause after line seizure
You can set the length of the pause inserted
between pressing the talk key c and sending
the phone number.
§Menu§
~
a
4IO1O
Enter digit for the pause length
(1 = 1 sec.; 2 = 3 sec.; 3 = 7 sec.)
and press §OK§.
Press and hold (idle status).
Changing the pause after the recall key
You can change the length of the pause if your
PABX requires this (refer to the user guide for
your PABX).
§Menu§
~
a
4IO14
Enter a digit for the length of the
pause (1 = 800 ms; 2 = 1600 ms;
3 = 3200 ms) and press §OK§.
Press and hold (idle status).
24
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / appendix.fm / 27.7.05
Appendix
Appendix
When it has fully dried out, you will normally be
able to use itagain.
Symbols and typographical
conventions used
Questions and answers
If you have any questions about using your
phone, visit us anytime at www.siemens.com/
gigasetcustomercare. The table below contains
a list of common problems and possible solutions.
This section explains the meaning of certain
symbols and typographical conventions that
are used in this user guide.
~
Enter digits or letters.
§Menu§
The display functions currently in
the bottom display line are shown
in reversed highlights. Press the
relevant display key to launch the
function.
q
The display is blank.
1. The handset is not switched on.
Press and hold the end call key a.
¥
2. The battery is flat.
Charge the battery or replace it (page 4).
¥
Press the top or bottom of the control key, e.g. when scrolling.
The handset does not respond to a key press.
The keypad lock is activated.
Press and hold the hash key # (page 10).
¥
c / Q / P etc.
Press the illustrated key on the
handset.
Base is flashing in the display.
External Calls / Internal Calls (example)
Select one of the menu functions
(External Calls or Internal Calls )
from the list and press §OK§.
¢
1. The handset is outside the range of the base station.
Move the handset closer to the base.
¥
2. The base station is not switched on.
Check the base station mains adapter
(page 4).
¥
¢
Audio Settings
Ringer Melody
(example)
Press §Menu§. Select Audio Settings
using q and press §OK§. Select
Ringer Melody using q and press
§OK§.
§Menu§
Handset does not ring.
The ringtone is switched off.
Activate the ringtone (page 22).
¥
You cannot hear a ringtone/dialling tone.
Care
¤
Base station's phone cord has been replaced.
When purchasing a new cord, ensure that it has
the correct pin connections (page 4).
¥
Wipe the base station and handset with a
damp cloth (do not use solvent) or an antistatic cloth.
The incoming call number is not displayed
although CLIP (page 9) is set.
Never use a dry cloth. This can cause static.
Contact with liquid
Phone number identification is not enabled.
The caller should ask his network provider to enable Calling Line Identification (CLI).
¥
!
You hear an error tone when keying an input
(a descending sequence of tones).
If the handset has come into contact with liquid:
Switch the handset off and remove the
batteries immediately.
Allow the liquid to drain from the handset.
Pat all parts dry, then place the handset with
the battery compartment open and the keypad facing down in a dry, warm place for at
least 72 hours (not in a microwave, oven
etc.).
Do not switch on the handset again until
it is completely dry.
¤
Action has failed/invalid input.
Repeat the operation.
Watch the display and refer to the operating
instructions if necessary.
¥
¤
¤
¤
25
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / appendix.fm / 27.7.05
Appendix
Service (Customer Care)
You can get assistance easily when you have technical questions or questions about how to use your
device by using our online support service on the Internet at:
www.siemens.com/customercare
This site can be accessed at any time wherever you are. It will give you 24/7 support for all our products. It also provides interactive troubleshooting, a list of FAQs and answers plus user guides for you
to download. You will also find frequently asked questions and answers in the Questions and
Answers section of this user guide in the appendix (page 25).
If the device needs to be repaired, please contact one of our Customer Care Centers:
Luxembourg . . . . . . . . . . . . . 43 84 33 99
Macedonia. . . . . . . . . . . . . . . . 02 13 14 84
Malaysia. . . . . . . . . . . . . . . 03 21 63 11 18
Malta . . . . . . . . . . . . 00 35 32 14 94 06 32
Mauritius . . . . . . . . . . . . . . . . . . 2 11 62 13
Mexico . . . . . . . . . . . . . .01 80 07 11 00 03
Morocco . . . . . . . . . . . . . . . . . 22 66 92 09
Netherlands . . . . . . . . . . . . 0900-3333102
New Zealand . . . . . . . . . . . 08 00 27 43 63
Norway . . . . . . . . . . . . . . . . . . 22 70 84 00
Oman. . . . . . . . . . . . . . . . . . . . . . 79 10 12
Pakistan . . . . . . . . . . . . . . . 02 15 66 22 00
Philippines . . . . . . . . . . . . . . 0 27 57 11 18
Poland . . . . . . . . . . . . . . . . 08 01 30 00 30
Portugal . . . . . . . . . . . . . . . . 8 00 85 32 04
Qatar . . . . . . . . . . . . . . . . . . . . 04 32 20 10
Romania . . . . . . . . . . . . . . 02 12 04 60 00
Russia. . . . . . . . . . . . . . . . (800) 200 10 10
Saudi Arabia . . . . . . . . . . . . 0 22 26 00 43
Serbia. . . . . . . . . . . . . . . . . 01 13 22 84 85
Singapore . . . . . . . . . . . . . . . . 62 27 11 18
Slovak Republic . . . . . . . . . 02 59 68 22 66
Slovenia . . . . . . . . . . . . . . . . 0 14 74 63 36
South Africa. . . . . . . . . . . . 08 60 10 11 57
Spain . . . . . . . . . . . . . . . . . . 9 02 11 50 61
Sweden . . . . . . . . . . . . . . . . 0 87 50 99 11
Switzerland . . . . . . . . . . . . 08 48 21 20 00
Taiwan . . . . . . . . . . . . . . . . 02 25 18 65 04
Thailand. . . . . . . . . . . . . . . . 0 22 68 11 18
Tunisia . . . . . . . . . . . . . . . . . 0 71 86 19 02
Turkey . . . . . . . . . . . . . . . 0 21 65 79 71 00
Ukraine . . . . . . . . . . . . . . 8 80 05 01 00 00
United Arab Emirates . . . . . 0 43 31 95 78
United Kingdom . . . . . . . 0 87 05 33 44 11
USA . . . . . . . . . . . . . . . . . 1 88 87 77 02 11
Vietnam . . . . . . . . . . . . . . . . . . 45 63 22 44
Abu Dhabi. . . . . . . . . . . . . . . 0 26 42 38 00
Argentina . . . . . . . . . . . . 0 80 08 88 98 78
Australia . . . . . . . . . . . . . . . 18 00 62 24 14
Austria . . . . . . . . . . . . . . . . 05 17 07 50 04
Bahrain . . . . . . . . . . . . . . . . . . . . . 40 42 34
Bangladesh . . . . . . . . . . . . . . 0 17 52 74 47
Belgium . . . . . . . . . . . . . . . . 0 78 15 22 21
Bosnia Herzegovina . . . . . . . 0 33 27 66 49
Brazil . . . . . . . . . . . . . . . . 0 80 07 07 12 48
Brunei . . . . . . . . . . . . . . . . . . . 02 43 08 01
Bulgaria. . . . . . . . . . . . . . . . . . 02 73 94 88
Cambodia . . . . . . . . . . . . . . . . 12 80 05 00
Canada . . . . . . . . . . . . . . 1 88 87 77 02 11
China . . . . . . . . . . . . . . . 0 21 50 31 81 49
Croatia . . . . . . . . . . . . . . . . . 0 16 10 53 81
Czech Republic . . . . . . . . . . 02 33 03 27 27
Denmark . . . . . . . . . . . . . . . . . 35 25 86 00
Dubai . . . . . . . . . . . . . . . . . . 0 43 96 64 33
Egypt. . . . . . . . . . . . . . . . . . . 0 23 33 41 11
Estonia . . . . . . . . . . . . . . . . . . 06 30 47 97
Finland . . . . . . . . . . . . . . . . 09 22 94 37 00
France. . . . . . . . . . . . . . . . . 01 56 38 42 00
Germany . . . . . . . . . . . . . . .01805 333 222
Greece . . . . . . . . . . . . . . 0 80 11 11 11 16
Hong Kong . . . . . . . . . . . . . . . 28 61 11 18
Hungary . . . . . . . . . . . . . . . 06 14 71 24 44
Iceland . . . . . . . . . . . . . . . . . . . 5 11 30 00
India . . . . . . . . . . . . . . 01 13 73 85 89 - 98
Indonesia . . . . . . . . . . . . 0 21 46 82 60 81
Ireland . . . . . . . . . . . . . . . . 18 50 77 72 77
Italy. . . . . . . . . . . . . . . . . . . 02 66 76 44 00
Ivory Coast . . . . . . . . . . . . . . . 80 00 03 33
Jordan . . . . . . . . . . . . . . . . . . 0 64 39 86 42
Kenya . . . . . . . . . . . . . . . . . . . . 2 72 37 17
Kuwait . . . . . . . . . . . . . . . . . . . 2 45 41 78
Latvia . . . . . . . . . . . . . . . . . . . . 7 50 11 14
Lebanon . . . . . . . . . . . . . . . . . 01 44 30 43
Libya . . . . . . . . . . . . . . . . . . 02 13 50 28 82
Lithuania. . . . . . . . . . . . . . . . 8 22 74 20 10
Please have your record of purchase ready when calling.
Replacement or repair services are not offered in countries where our product is not sold by authorised
dealers.
26
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / appendix.fm / 27.7.05
Appendix
Authorisation
Base station power consumption
In standby mode: approx. 2W
This device is intended for analogue
phone lines in your network.
Country-specific requirements have been
taken into consideration.
During a call: approx. 3W
General specifications
We, Siemens AG, declare that this device
meets the essential requirements and
other relevant regulations laid down in
Directive 1999/5/EC.
A copy of the 1999/5/EC Declaration of
Conformity is available at this Internet
address: http://www.siemens.com/
gigasetdocs.
Specifications
Recommended batteries
(Valid at the time of going to press)
Handset operating times/charging times
The following information relates to batteries
with a capacity of 650mAh.
approx 130hours (5days)
approx. 13hours
Charging time
approx. 13hours
is supported
No. of channels
60 duplex channels
Radio frequency
range
1880–1900 MHz
Duplex method
Time multiplex, 10 ms frame
length
Channel grid
1728 kHz
Bit rate
1152 kbit/s
Modulation
GFSK
Language code
32 kbit/s
Transmission power
10 mW, average power per
channel
Range
up to 300 m outdoors,
up to 50 m indoors
Base station power
supply
230 V ~/50 Hz
Dialling mode
DTMF (tone dialling)/DP (dial
pulsing)
Flash time
250 ms
Base station dimensions
102x 124 x 81mm
(L x W x H)
Handset dimensions 141 x 53 x 31mm
(L × W × H)
The handset is supplied with two recommended batteries.
Calling time
is supported
GAP standard
Environmental con- +5 °C to +45 °C;
ditions for operation 20 % to 75 % relative humidity
Nickel-metal-hydride (NiMH):
u Sanyo Twicell 650
u Sanyo Twicell 700
u Sanyo NiMH 800
u Panasonic 700 mAh "for DECT"
u GP 550mAh
u GP 700mAh
u GP 850mAh
u Yuasa Technology AAA Phone 600
u Yuasa Technology AAA Phone 700
u Yuasa Technology AAA 800
u VARTA Phone Power AAA 700mAh
Standby time
DECT standard
The operating and charging times apply only
when using the recommended batteries.
27
Base station weight
121 g
Weight of handset
with battery
116 g
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / appendix.fm / 27.7.05
Appendix
Writing and editing a text message
Entering special characters
The following rules apply when writing a text
message:
u The cursor is controlled with t s.
u Characters are added to the left of the cursor.
u Press the hash key # briefly to switch
from "Abc" mode to "123", from "123" to
"abc", and from "abc" to "Abc" (upper case:
1st letter upper case, all others lower case).
Press the hash key # before entering the
letter.
u Press and hold the hash key # lang
drücken: Shows the selection line of the
characters assigned to the hash key.
u The first letter of the name of directory
entries is automatically capitalised, followed
by lower case letters.
Standard characters
1
Q
*)
**)
Space
Space
.
*
Abc-->
123
2x
1
Â
,
/
123 -->
3x
£
1
?
(
#
4x
$
â
!
)
@
5x
¥
£
0
<
\
6x
¤
abc
$
+
=
&
7x
¥
-
>
§
8x
¤
:
%
¿
Editing text
10x
¡
When you press a key and hold it, the characters of that key appear in the bottom display
line and are highlighted one after the other.
When you release the key the highlighted character is inserted into the input field. For how to
enter special characters, see page 28.
11x
“
12x
‘
13x
;
14x
_
*) Directory and other lists
**) When writing an SMS
Order of directory entries
The directory entries are usually sorted in
alphabetical order. Spaces and digits take first
priority. The sort order is as follows:
1. Space (shown here as s)
2. Digits (0–9)
3. Letters (alphabetical)
4. Other characters
To get round the alphabetical order of the
entries, insert a space or a digit in front of the
name. These entries will then move to the
beginning of the directory. Names which you
have preceded with an asterisk will move to the
end of the directory.
28
#
1x
9x
The display briefly shows whether upper or
lower case letters or digits is selected when you
switch from one mode to the next. The bottom
text line displays "abc -> Abc", "Abc -> 123" or
"123 -> abc".
P
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / accessories_SAG.fm / 27.7.05
Accessories
Accessories
Gigaset Handsets
Upgrade your Gigaset to a cordless PABX:
Gigaset Handset C45
u
u
u
u
u
u
u
u
u
Illuminated colour display (4096 colours)
Various different screensavers
Illuminated keypad
Handsfree operation
Polyphonic ringer melodies
Phonebook for around 100 entries
SMS (CLIP must be enabled)
Alarm clock
Headset socket
www.siemens.com/gigasetc45
All accessories and batteries are available from your mobile phone retailer.
Or you can order direct online via the Online Shop: www.siemens.com/shop. The Online Shop also
has the latest product information.
Only use original accessories. This will avoid possible health risks and damage, and
also ensure that all the relevant regulations are complied with.
29
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / C450_laender_SIX.fm / 27.7.05
Index
Index
Changing PIN . . . . . . . . . . . .
Changing system PIN . . . . . . .
Characters
deleting . . . . . . . . . . . . . .
Charge status (battery) . . . . . .
Charge status display . . . . . . .
CLI, CLIP . . . . . . . . . . . . . . .
Colour scheme . . . . . . . . . . .
Confirmation tone . . . . . . . . .
Connection socket for headset .
Consultation (internal) . . . . . .
Contrast . . . . . . . . . . . . . . .
Control key . . . . . . . . . . . . .
Correcting incorrect input . . . .
Customer Care . . . . . . . . . . .
Numerics
24 hours in advance (alarm clock) . . . . . . 23
A
Accessories . . . . . . . . . . . . . . . . . . . . . 29
Activating
advisory tones . . . . . . . . . . . . . . . . . 22
auto answer . . . . . . . . . . . . . . . . . . . 21
handsfree talking . . . . . . . . . . . . . . . . 9
internal listening in . . . . . . . . . . . . . . 20
keypad lock . . . . . . . . . . . . . . . . . . . 10
SMS function . . . . . . . . . . . . . . . . . . 17
suppressing ringtone . . . . . . . . . . . . . 22
Activating/deactivating SMS function . . . . 17
Advisory tones . . . . . . . . . . . . . . . . . . . 22
Alarm clock . . . . . . . . . . . . . . . . . . . . . 22
key. . . . . . . . . . . . . . . . . . . . . . . . . . 1
Alarm repeat . . . . . . . . . . . . . . . . . . . . 23
Answering machine, see also Network mailbox
Auto answer . . . . . . . . . . . . . . . . . . 9, 21
Automatic network provider code . . . . . . 14
Deactivating
advisory tones . . . . . . . . . . . .
auto answer . . . . . . . . . . . . .
handsfree talking . . . . . . . . . .
internal listening in . . . . . . . .
keypad lock . . . . . . . . . . . . . .
preselection . . . . . . . . . . . . .
SMS function . . . . . . . . . . . .
suppressing ringtone . . . . . . .
Dialling
directory . . . . . . . . . . . . . . .
with quick dial . . . . . . . . . . . .
Dialling mode . . . . . . . . . . . . . .
Digital clock . . . . . . . . . . . . . . .
Directory . . . . . . . . . . . . . . . . .
copying number from text . . . .
opening . . . . . . . . . . . . . . . .
order of entries . . . . . . . . . . .
selecting entry . . . . . . . . . . .
sending entry/list to handset . .
storing entry . . . . . . . . . . . . .
storing number of sender (SMS)
storing the first number . . . . .
using to enter numbers . . . . . .
Display
call duration/charges . . . . . . .
changing display language . . . .
colour scheme . . . . . . . . . . . .
contrast . . . . . . . . . . . . . . . .
in idle status . . . . . . . . . . . . .
network mailbox message . . . .
number (CLI/CLIP) . . . . . . . . .
screensaver. . . . . . . . . . . . . .
setting . . . . . . . . . . . . . . . . .
Display keys . . . . . . . . . . . . . . .
. . . . . . . . . . 23
...........4
. . . . . . . . . . 23
. . . . . . . . . . 27
. . . . . . . . . . 23
. . . . . . . . . . 23
. . . . . . . . . 5, 6
. . . . . . . . . 1, 5
...........4
...........6
. . . . . . . . . . 27
. . . . . . . . . . 22
...........6
C
Call
answering . . . . . . . . . .
caller listening in . . . . .
ending . . . . . . . . . . . .
external . . . . . . . . . . .
internal . . . . . . . . . . . .
transferring (connecting)
Call acceptance . . . . . . . .
Call duration . . . . . . . . . .
Call waiting, internal call . .
Calling back caller . . . . . .
Calling back from calls list .
Calling Line Identification. .
Calls list . . . . . . . . . . . . .
Cancelling(operation) . . . .
Care of the telephone . . . .
. . . . . . . .11
. . . . . . .1, 5
........ 6
........ 9
. . . . . . . .21
. . . . . . . .22
. . . . . . .1, 6
. . . . . . . .20
. . . . . . . .21
. . . . . .1, 10
. . . . . . . .11
. . . . . . . .26
D
B
Base station
changing system PIN . . .
installing and connecting
operating on PABX . . . .
power consumption . . .
restoring default settings
setting . . . . . . . . . . . .
Battery
charging . . . . . . . . . . .
display . . . . . . . . . . . .
fitting . . . . . . . . . . . . .
icon . . . . . . . . . . . . . .
recommended batteries .
warning tone . . . . . . . .
Belt clip . . . . . . . . . . . . .
. . . . . . . .23
. . . . . . . .23
...........9
. . . . . . . . . . 20
...........9
...........9
. . . . . . . . . . 20
. . . . . . . . . . 20
. . . . . . . . . . 21
. . . . . . . . . . 14
. . . . . . . . . . 20
. . . . . . . . . . 14
. . . . . . . . . . 14
...........9
. . . . . . . . . . 13
. . . . . . . . . . 10
. . . . . . . . . . 25
E
. . . . . .22
. . . . . .21
...... 9
. . . . . .20
. . . . . .10
. . . . . .14
. . . . . .17
. . . . . .22
. . . . . .12
. . . . . .12
. . . . . .23
. . . . . .21
. . . . . .12
. . . . . .13
. . . . . .10
. . . . . .28
. . . . . .12
. . . . . .12
. . . . . .12
. . . . . .17
. . . . . .12
. . . . . .13
. . . . . .14
. . . . . .21
. . . . . .21
. . . . . .21
...... 1
. . . . . .19
...... 9
. . . . . .21
. . . . . .21
. . . .1, 10
Earpiece mode . . . . . . . . . . . . . . . . . . . 9
Earpiece volume . . . . . . . . . . . . . . . . . .21
Electricity consumption, see Power
consumption
30
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / C450_laender_SIX.fm / 27.7.05
Index
End call key . .
Ending, call . .
Entering flash
Error tone . . .
. . . . . . . . . . . . . . . . . . 1, 9
....................9
....................1
. . . . . . . . . . . . . . . . . . . 22
hash key. . . .
keypad lock . .
message key .
On/Off key . .
paging key . .
quick dial . . .
recall key . . .
star key . . . .
talk key . . . .
F
Fast access
network mailbox . . . . . . . . . . . . . . . . 19
H
Handset
activating/deactivating . . . . .
advisory tones . . . . . . . . . .
contact with liquid . . . . . . .
de-registering. . . . . . . . . . .
display language . . . . . . . . .
idle status . . . . . . . . . . . . .
loudspeaker volume . . . . . .
operating and charging times
registering . . . . . . . . . . . . .
restoring default settings . . .
searching for . . . . . . . . . . .
setting (individual) . . . . . . .
setting up for use . . . . . . . .
transferring a call . . . . . . . .
using several handsets . . . . .
Handset charging times . . . . . .
Handset operating time . . . . . .
Handsfree
key. . . . . . . . . . . . . . . . . .
Handsfree talking . . . . . . . . . .
Hash key . . . . . . . . . . . . . . .
Headset . . . . . . . . . . . . . . . .
Hearing aids . . . . . . . . . . . . .
I
Idle status (display) . . . . . .
Illumination . . . . . . . . . .
Incorrect input (correction)
Info tones . . . . . . . . . . . .
Installing, base station . . .
Internal
consultation . . . . . . . .
listening in . . . . . . . . .
making calls . . . . . . . . .
Internal call . . . . . . . . . . .
call waiting . . . . . . . . .
K
Key click . . . . . . . . . . . . .
Keypad lock . . . . . . . . . .
Keys
alarm clock key . . . . . . .
assigning directory entry
control key . . . . . . . . .
display keys . . . . . . . . .
end call key . . . . . . . . .
end-call key . . . . . . . . .
handsfree key. . . . . . . .
L
. . . . . . . 10
. . . . . . . 22
. . . . . . . 25
. . . . . . . 23
. . . . . . . 21
. . . . . . . 10
. . . . . . . 21
. . . . . . . 27
. . . . . . . 19
. . . . . . . 23
. . . . . . . 20
. . . . . . . 21
........4
. . . . . . . 20
. . . . . . . 19
. . . . . . . 27
. . . . . . . 27
Last number redial . . . . . . . . .
Liquid . . . . . . . . . . . . . . . . .
List
calls list . . . . . . . . . . . . . .
draft message list (SMS) . . .
entry . . . . . . . . . . . . . . . .
incoming message list (SMS)
last number redial list . . . . .
missed calls . . . . . . . . . . .
Listening in to call . . . . . . . . .
Lock (keypad) . . . . . . . . . . . .
Loudspeaker volume . . . . . . .
M
Mains adapter. . . . . . . . .
Making calls
answering a call . . . . . .
external . . . . . . . . . . .
internal . . . . . . . . . . .
Making cost-effective calls
Medical appliances . . . . .
Menu
back one menu level . . .
end tone . . . . . . . . . .
menu guidance . . . . . .
overview . . . . . . . . . .
Message
key . . . . . . . . . . . . . .
Message key . . . . . . . . . .
opening list. . . . . . . . .
opening lists . . . . . . . .
Missed call . . . . . . . . . . .
........1
........9
. . . . . 1, 10
. . . . . . 1, 6
........3
. . . . . . . . 1, 10
. . . . . . . . . . 21
. . . . . . . . . . 11
. . . . . . . . . . 22
...........4
..........
..........
..........
..........
..........
. . . . . . . . . . . . . . . .1, 10
. . . . . . . . . . . . . . . . . .10
. . . . . . . . . . . . . . . .1, 13
.................. 1
.................. 1
. . . . . . . . . . . . . . . . . .12
.................. 1
. . . . . . . . . . . . . . . .1, 22
. . . . . . . . . . . . . . . . .1, 9
20
20
20
20
20
N
. . . . . . . .13
. . . . . . . .25
. . . . . . . .13
. . . . . . . .15
. . . . . . . .13
. . . . . . . .16
. . . . . . . .13
. . . . . . . .13
. . . . . . . .20
. . . . . . . .10
. . . . . . . .21
........... 3
........... 9
........... 9
. . . . . . . . . . .20
. . . . . . . . . . .14
........... 3
. . . . . . . . . . .10
. . . . . . . . . . .22
. . . . . . . . . . .11
........... 7
........... 1
........... 1
. . . . . . . . . . .16
. . . . . . . . . . .13
. . . . . . . . . . .13
Network mailbox . . . . . . . . . . . . . .
storing entry . . . . . . . . . . . . . . .
Network provider code, automatic . .
Number
copying from directory . . . . . . . .
displaying caller's number (CLIP) . .
entering network mailbox number .
entry using directory. . . . . . . . . .
setting for SMS centre . . . . . . . . .
storing in directory . . . . . . . . . . .
storing in the directory . . . . . . . .
storing sender in the directory . . .
. . . . . . . . . . 22
. . . . . . . . . . 10
...........1
. . . . . . . . . . 12
. . . . . . . . 1, 10
. . . . . . . . 1, 10
. . . . . . . . . 1, 9
. . . . . . . . . . 10
...........1
31
. . . .19
. . . .19
. . . .14
. . . .13
.... 9
. . . .19
. . . .13
. . . .17
. . . .12
. . . .13
. . . .17
Gigaset C 450 / IM-Nord EN / A31008-M1706-R201-1-7619 / C450_laender_SIX.fm / 27.7.05
Index
SMS . . . . . . . . . . . . . . . . . . .
deleting . . . . . . . . . . . . . . .
draft message list . . . . . . . . .
forwarding . . . . . . . . . . . . .
incoming message list . . . . . .
reading . . . . . . . . . . . . . . .
registration wizard . . . . . . . .
replying to and forwarding . . .
self help with error messages .
send centre . . . . . . . . . . . . .
sending . . . . . . . . . . . . . . .
storing number . . . . . . . . . .
to PABX . . . . . . . . . . . . . . .
troubleshooting . . . . . . . . . .
writing . . . . . . . . . . . . . . . .
writing text . . . . . . . . . . . . .
SMS Centre
changing number . . . . . . . .
setting . . . . . . . . . . . . . . . .
Snooze (alarm clock) . . . . . . . .
Special characters . . . . . . . . . .
Star key . . . . . . . . . . . . . . . . .
Suppressing
first ring . . . . . . . . . . . . . . .
O
On/Off key . . . . . . . . . . . . . . . . . . . . . . 1
Operation (preparing to use the phone) . . . 4
Order of entries in directory . . . . . . . . . . 28
P
PABX
operating base station on PABX .
pause times . . . . . . . . . . . . . .
setting dialling mode . . . . . . . .
setting flash time . . . . . . . . . .
SMS . . . . . . . . . . . . . . . . . . .
Pack contents . . . . . . . . . . . . . .
Paging . . . . . . . . . . . . . . . . . . .
Pause times (PABX) . . . . . . . . . . .
Phone jack assignment . . . . . . . .
Power consumption (base station) .
Preselection . . . . . . . . . . . . . . .
saving, changing entry . . . . . . .
. . . . . 23
. . . . . 24
. . . . . 23
. . . . . 23
. . . . . 17
......4
. . . 1, 20
. . . . . 24
......4
. . . . . 27
. . . . . 14
. . . . . 14
Q
Questions and answers . . . . . . . . . . . . . 25
Quick dial . . . . . . . . . . . . . . . . . . . . . . 12
R
Recall key . . . . . . . . . . .
Registering (handset) . . .
Registration wizard (SMS)
Restoring default settings
base station . . . . . . . .
handset . . . . . . . . . .
Ringtone
changing . . . . . . . . . .
setting melody . . . . . .
setting volume . . . . . .
suppressing . . . . . . . .
S
............1
. . . . . . . . . 5, 19
. . . . . . . . . . . 15
T
Talk key . . . . . . . . . . .
Technical data . . . . . .
Text message, see SMS
Troubleshooting . . . . .
SMS . . . . . . . . . . .
. . . . . . . . . . . 23
. . . . . . . . . . . 23
. . . . . . .17
. . . . . . .17
. . . . . . .23
. . . . . . .28
. . . . .1, 22
. . . . . . .22
. . . . . . . . . . . .1, 9
. . . . . . . . . . . . .27
. . . . . . . . . . . . .25
. . . . . . . . . . . . .17
U
. . . . . . . . . . . 21
. . . . . . . . . . . 22
. . . . . . . . 10, 21
. . . . . . . . . . . 22
Safety precautions . . . . . . .
Screensaver . . . . . . . . . . .
Searching
for handset . . . . . . . . . .
in directory . . . . . . . . . .
Sending
directory entry to handset.
SMS . . . . . . . . . . . . . . .
Service . . . . . . . . . . . . . . .
Setting date . . . . . . . . . . .
Setting flash time (PABX) . . .
Setting melody (ringtone) . .
Setting time . . . . . . . . . . .
Setting volume
earpiece . . . . . . . . . . . .
handset loudspeaker . . . .
loudspeaker . . . . . . . . . .
ringtone . . . . . . . . . . . .
Setting wake up time . . . . .
Shortcut (digit combination)
Signal strength . . . . . . . . .
. . . . . . .15
. . . . . . .16
. . . . . . .15
. . . . . . .16
. . . . . . .16
. . . . . . .16
. . . . . . .15
. . . . . . .16
. . . . . . .18
. . . . . . .15
. . . . . . .15
. . . . . . .17
. . . . . . .17
. . . . . . .17
. . . . . . .15
. . . . . . .28
Unknown . . . . . . . . . . . . . . . . . . . . . . 9
Unknown caller . . . . . . . . . . . . . . . . . . . 9
V
Viewing network mailbox message . . . . . .19
Volume
ringtone . . . . . . . . . . . . . . . . . . . . . .21
..........3
. . . . . . . . . 21
W
. . . . . . . . . 20
. . . . . . . . . 12
Warning tone (battery) . . . . . . . . . . . . . .22
Writing, editing text . . . . . . . . . . . . . . . .28
. . . . . . . . . 12
. . . . . . . . . 15
. . . . . . . . . 26
..........6
. . . . . . . . . 23
. . . . . . . . . 22
..........6
. . . . . . . . . 21
. . . . . . . . . 21
. . . . . . . . . 21
. . . . . . . . . 21
. . . . . . . . . 22
..........7
..........1
32