3-856-161-11 (1)
Operating Instructions
EN
F
ES
S
C
CDP-CE105
 1996 by Sony Corporation
WARNING
To prevent fire or shock
hazard, do not expose
the unit to rain or
moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to
qualified personnel only.
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
CAUTION
You are cautioned that any changes or
modification not expressly approved in
this manual could void your authority to
operate this equipment.
Owner’s Record
The model and serial numbers are
located on the rear of the unit.
Record the serial number in the space
provided below. Refer to them whenever
you call upon your Sony dealer
regarding this product.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
INFORMATION
2
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or
television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
Model No. CDP-CE105
Serial No.
For the customers in Australia
The following caution label is located
inside the unit.
This appliance is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT
MARKING is located on the rear
exterior.
Precautions
On safety
• Caution — The use of optical
instruments with this product will
increase eye hazard.
• Should any solid object or liquid fall
into the cabinet, unplug the player and
have it checked by qualified personnel
before operating it any further.
On power souces
• Before operating the player, check that
the operating voltage of the player is
identical with your local power
supply. The operating voltage is
indicated on the nameplate at the rear
of the player.
• The player is not disconnected from
the AC power source as long as it is
connected to the wall outlet, even if
the player itself has been turned off.
• If you are not going to use the player
for a long time, be sure to disconnect
the player from wall outlet. To
disconnect the AC power cord , grasp
the plug itself; never pull the cord.
• AC power cord must be changed only
at the qualified service shop.
On placement
• Place the player in a location with
adequate ventilation to prevent heat
build-up in the player.
• Do not place the player on a soft
surface such as a rug that might block
the ventilation holes on the bottom.
• Do not place the player in a location
near heat sources, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
On operation
• If the player is brought directly from a
cold to a warm location, or is placed in
a very damp room, moisture may
condense on the lenses inside the
player. Should this occur, the player
may not operate properly. In this case,
remove the disc and leave the player
turned on for about an hour until the
moisture evaporates.
On cleaning
• Clean the cabinet, panel and controls
with a soft cloth slightly moistened
with a mild detergent solution. Do not
use any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine.
If you have any questions or
problems concerning your player,
please consult your nearest Sony
dealer.
Getting Started
Welcome!
TABLE OF CONTENTS
Thank you for purchasing the Sony
Compact Disc Player. Before operating
the unit, please read this manual
thoroughly and retain it for future
reference.
Getting Started
About This Manual
Playing a CD ........................................................................................................ 6
The instructions in this manual are for
model CDP-CE105.
Convention
• The following icon is used in this
manual:
Indicates hints and tips for
making the task easier.
Unpacking ........................................................................................................ 4
Hooking Up the System ................................................................................. 4
Playing CDs
Using the Display ........................................................................................... 8
Exchanging a Disc While Playing a Disc ..................................................... 8
Locating a Specific Disc ................................................................................. 8
Locating a Specific Track or a Point in a Track .......................................... 9
Playing Tracks Repeatedly (Repeat play) ................................................... 9
Playing in Random Order (Shuffle Play) .................................................... 9
Creating Your Own Program (Program Play) .......................................... 10
Additional Information
Notes on CDs ................................................................................................. 11
Troubleshooting ............................................................................................ 12
Specifications ................................................................................................. 12
Index
Index ............................................................................................................... 13
3
Getting Started
Unpacking
Hooking Up the System
Check that you received the following item:
• Audio cord (1)
Overview
This section describes how to hook up the CD player to
an amplifier. Be sure to turn off the power of each
component before making the connections.
CD player
Line output
To
an AC outlet
(R)
Audio input
(L)
: Signal flow
Line output
(L)
Audio input
(R)
Amplifier
To an AC outlet
What cords will I need?
Audio cord (supplied) (1)
White
(L)
Red
(R)
4
White
(L)
Red
(R)
Getting Started
Hookups
When connecting the audio cord, be sure to match the
color-coded cord to the appropriate jacks on the
components: Red (right) to Red and White (left) to
White. Be sure to make connections firmly to avoid
hum and noise.
CD player
Amplifier
LINE OUT
R L
INPUT
CD
L
R
Connecting the AC power cord
Connect the AC power cord to a wall outlet.
Transporting the player
Before transporting the player, follow the procedure
below to return the internal mechanisms back to their
original position.
1 Remove all the discs from the disc tray.
2 Close the front cover and wait until “no dISC”
appears in the display.
3 Press POWER to turn off the player.
5
Basic Operations
Playing a CD
2
6
POWER
35
4
OPEN
CONTNUE SHUFFLE PROGRAM REPEAT
DISC 1
• See pages 4 – 5 for the hookup
information.
1
2
3
DISC 2
DISC 3
DISC SKIP
DISC 4
DISC 5
Turn on the amplifier and select the CD player position so that
you can listen to the sound from this player.
Press POWER to turn on the player.
Press OPEN, and place a disc on the disc tray at the loading
position.
Playing position
With the label
side up
Disc number
and indicator
Place the disc after the indicator lights up.
You can select the disc tray
directly
Press one of the DISC 1–5
buttons. The disc tray rotates
and you can place a disc in the
empty disc compartments
(loading position).
6
4
Disc tray
Loading
position
To place other discs, press DISC SKIP and place the discs in the
order you want to play.
Each time you press the button, the disc tray rotates and you
can place the discs in the empty disc compartments.
The player will play the disc at the loading position.
Basic Operations
5
Press CONTINUE to select ALL DISCS or 1 DISC Continuous
Play mode.
Each time you press CONTINUE, “ALL DISCS” or “1␣ DISC”
appears in the display.
You can select the disc you want
to play directly
Press one of the DISC 1–5
buttons with the front cover
closed.
If there is no disc in the disc
number, the disc tray rotates
and plays the next disc.
6
When you select
The player plays
ALL DISCS
All discs in the player consecutively in the order of
disc number
1␣ DISC
Only one disc at the loading position
Close the front cover and press ·P to play a disc.
Adjust the volume on the amplifier.
To stop playing
Press p.
·P p
To
Press
Pause
·P
Resume playing after pause
·P
Go to the next track
)±
Go back to the preceding track
≠0
Go to the next disc
DISC SKIP
Select a disc directly
DISC 1–5
Remove the CD
OPEN
Basic Operations
OPEN DISC 1 – 5 DISC SKIP
Note
When the front cover is open, if the
play of the current disc ends, the
player stops playing.
If you want to play other discs,
close the front cover and press the
DISC 1-5 button.
≠0/
)±
7
Playing CDs
Using the Display
You can check information about the disc using the
display.
ill006
DISC SKIP
Exchanging a Disc While
Playing a Disc
You can open the front cover while playing a disc so
that you exchange a disc without interrupting the
playing of the current disc.
ill008
Checking the total number and playing
time of the tracks
Close the front cover.
The display shows the current disc number, the total
number of tracks and total playing time.
Current disc number
Total playing time
ALL DISCS
1
DISC
2
3
TRACK
1 10
4
MIN
OPEN
1
Press OPEN and exchange the disc at the loading
position.
2
Close the front cover.
If you select the Continuous Play and ALL DISCS,
the exchanged disc number starts flashing.
The play of the current disc ends, and a disc whose
disc number is flashing starts playing.
5
SEC
46 28
Note
While the disc number is flashing, if you press any buttons,
the flashing stops and the player returns to the mode before
the disc was exchanged.
Total number of tracks
The information also appears when you press DISC
SKIP in the stop mode.
Locating a Specific Disc
You can locate any disc before or while playing a disc.
Notes on the disc number indications
• The double-circle around a disc number indicates the disc is
ready to be played.
• When a disc compartment is recognized as empty, the disc
number disappears.
DISC 1 – 5 DISC SKIP
Display information while playing a disc
While playing a disc, the display shows the current
disc number, track number, and playing time of the
track.
Current disc number
Playing time
ALL DISCS
1
2
DISC
TRACK
1
1
3
4
MIN
SEC
1 56
Current track number
8
5
To locate
Press
The next disc
DISC SKIP while playing a disc
A specific disc directly
DISC 1 – 5
Playing CDs
Locating a Specific Track or a
Point in a Track
You can quickly locate any track while playing a disc
using the ≠0/)± (AMS: Automatic Music
Sensor) buttons. You can also locate a specific point in
a track while playing a disc.
≠0/)±
When the disc is played in
The player repeats
Continuous Play
(ALL DISCS) (page 7)
All the tracks on all discs
Continuous Play
(1␣ DISC) (page 7)
All the tracks on the current
disc
Shuffle Play
(ALL DISCS) (page 9)
All the tracks on all discs in
random order
Shuffle Play
(1␣ DISC) (page 9)
All the tracks on the current
disc in random order
Program Play (page 10)
The same program
To cancel Repeat Play
Press REPEAT repeatedly until “REPEAT” disappears from
the display.
Repeating the current track
To locate
Press
The next or
succeeding tracks
)± repeatedly until you find the
track
You can repeat the current track.
The current or
preceding tracks
≠0 repeatedly until you find the
track
While the track you want is being played, press
REPEAT repeatedly until “REPEAT 1” appears in the
display.
A point while
)± (forward) or ≠0
monitoring the sound (backward) and hold down until you
find the point
)± (forward) or ≠0
A point quickly by
observing the display (backward) and hold down until you
find the point. You will not hear the
during pause
sound during the operation.
Note
If “
” appears in the display, the disc has reached the end
while you were pressing and holding )±. Press ≠0
to go back.
Playing in Random Order
(Shuffle Play)
You can have the player “shuffle” tracks and play in
random order. The player shuffles all the tracks on all
discs or on the disc you’ve specified.
SHUFFLE DISC 1 – 5
Playing Tracks Repeatedly
(Repeat Play)
You can play discs/tracks repeatedly in any play
mode.
·P
Shuffle Play on all discs
REPEAT
Press REPEAT while playing a disc.
“REPEAT” appears in the display. The player repeats
the discs/tracks as follows:
You can play all tracks on all discs in random order.
1
Press SHUFFLE repeatedly until “ALL DISCS”
appears in the display.
2
Press ·P to start ALL DISCS Shuffle Play.
The
indication appears while the player is
“shuffling” the tracks.
To cancel Shuffle Play
Press CONTINUE.
9
Playing CDs
You can start Shuffle Play while playing
1
Press PROGRAM.
“PROGRAM” appears in the display.
If a program is already stored, the last step of the
program appears in the display. When you want to
erase the whole program, hold down p until “ALL
CLr” appears for about 2 seconds in the
display(see page 11).
2
Press DISC 1 – 5 to select the disc.
Press SHUFFLE, and Shuffle Play starts from the current
track.
You can specify discs during Shuffle Play (Select
Shuffle Play)
You can specify discs during ALL DISCS Shuffle Play
mode, and the tracks on the specified discs are played in
random order.
Circles appear only arround the specified disc numbers
in the display. To cancel the selected discs, press
DISC 1 – 5 again. The circles disappear.
To return to ALL DISCS Shuffle Play, press SHUFFLE
twice.
PROGRAM
1
DISC
2
TRACK
1 AL
Shuffle Play on one disc
You can play all tracks on a specific disc in random
order.
1
Press SHUFFLE repeatedly until “1␣ DISC” appears
in the display.
2
Press DISC 1 – 5 to start 1␣ DISC Shuffle Play on
the selected disc.
The
indication appears while the player is
“shuffling” the tracks.
3
4
5
MIN
SEC
42 11
“AL” in the display stands for “all” tracks.
When you want to program the whole disc as one
step, skip Step 3 and 4 and go to Step 5.
3
Press )± or ≠0 to choose a track.
The chosen track number and the total playing
time flashes in the display.
PROGRAM
To cancel Shuffle Play
1
Press CONTINUE.
You can start Shuffle Play while playing
Press SHUFFLE, and Shuffle Play starts from the current
track.
2
DISC
TRACK
1
5
3
4
5
MIN
SEC
13 18
Total playing time
4
Creating Your Own Program
(Program Play)
You can arrange the order of the tracks on the discs
and create your own program. The program can
contain up to 32 steps.
Press PROGRAM.
“PROGRAM”, track number and play order
indications appear for a about 3 seconds in the
display and then goes back to the Step 3 display.
Last programmed track
PROGRAM
1
PROGRAM DISC 1 – 5
·P p
10
Playing order
2
DISC
TRACK
1
5
3
4
5
STEP
3
Playing CDs
5
6
To program other discs or tracks, do the following:
Additional Information
Playing CDs
Notes on CDs
To program
Repeat Step(s)
Other discs
2
On handling CDs
Other tracks on the same disc
3 and 4
Other tracks on other discs
2, 3 and 4
• To keep the disc clean, handle the disc by its edge. Do not
touch the surface.
• Do not stick paper or tape on the disc.
Press ·P to start Program Play.
To cancel Program Play
Not this way
Press CONTINUE.
You can create your program while checking the disc
labels
When the front cover is open, follow Steps 1 to 6 while
pressing DISC SKIP to check the disc labels.
Note that, if the programmed track number isn’t found
on the disc, that step is automatically erased.
The program remains even after Program Play ends
When you press ·P, you can play the same program
again.
• Do not expose the disc to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in direct
sunlight as there can be considerable rise in temperature
inside the car.
• Do not use any commercially available stabilizer. If you do,
the disc and the player may be damaged.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning cloth. Wipe
the disc from the center out.
The program remains until you erase it or turn off the
player
If you exchange discs, the programmed disc and track
numbers remain. So, the player plays only the existing
disc and track numbers. However, the disc and track
numbers that aren’t found in the player or on the disc are
deleted from the program, and the rest of the program is
played in the programmed order.
Note
• Do not use solvents such as benzine, thinner, commercially
available cleaners or anti-static spray intended for vinyl
LPs.
The total playing time doesn’t appear when:
—You have programmed a track whose number exceeds 20.
—The total playing time of the program exceeds 200 minutes.
—Front cover is opened.
Changing the track order
You can change your program before you start playing.
To
Press
Erase the last step in the
program
p. Each time you press the
button, the last step will be
cleared.
Change the whole program
completely
p until “ALL CLr” appears
in the display. Create a new
program following the
programming procedure.
11
Playing CDsInformation
Additional
Troubleshooting
Specifications
If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
Compact disc player
Laser
Semiconductor laser (λ = 780 nm)
Emission duration: continuous
Laser output
Max 44.6 µW*
* This output is the value measured at
a distance of 200 mm from the
objective lens surface on the Optical
Pick-up block with 7 mm aperture.
Frequency response
2 Hz to 20 kHz ± 1.0 dB
Signal-to-noise ratio
More than
100dB
Dynamic range
More than
96dB
Harmonic distortion
Less than
Channel separation
More than 86dB
There’s no sound.
/Check that the player is connected securely.
/Make sure you operate the amplifier correctly.
The CD does not play.
/There’s no CD inside the player (“no dISC”
appears). Insert a CD.
/Place the CD with the label side up on the disc
tray correctly.
/Clean the CD (page 11).
/Moisture has condensed inside the player.
Remove the disc and leave the player turned on
for about an hour (page 2).
The player functions incorrectly.
/The microcomputer chips may be operating
incorrectly. Turn the power off, then turn it
back on to reset the player.
0.01%
Output
LINE OUT
Jack
type
Maximum
output
level
Phono
jacks
Over 10 kilohms
2V
(at 50 kilohms)
Load
impedance
General
Power requirements
Where purchased␣
Power requirements
USA
120 V AC, 60 Hz
Australia
240 V AC, 50/60 Hz
Power consumption
10 W
Dimensions (approx.)
(w/h/d)
430 × 135 × 400 mm
(17 × 5 3/8 × 15 3/4 in.) incl. projecting
parts
Mass (approx.)
4.5 kg (9 lbs 15 oz)
Supplied accessories
Audio cord (2 phono plugs – 2 phono plugs) (1)
Design and specifications are subject to change without notice.
12
Index
Names of controls
Index
Buttons
A, B
CONTINUE 7
DISC 1 – 5 6
DISC SKIP 6
OPEN 6
PROGRAM 10
REPEAT 9
SHUFFLE 9
·P 7
p 7
≠0/)±
AMS 9
Automatic Music Sensor. See
AMS
C, D, E, F, G
Connecting 4
Continuous Play 7
Exchanging a disc while
playing a disc 8
H, I, J, K
Handling CDs 11
Hookups 4
overview 4
Switch
POWER 6
L, M, N, O
Locating
by monitoring 9
by observing the display
using AMS 10
P, Q
7, 9
Others
9
Disc compartment 6
Disc tray 6
Display 8
Loading position 6
Playing position 6
Playing
Continuous Play 7
Program Play 10
Repeat Play 9
Shuffle Play 9
Program 10
changing 11
R
Repeating
9
S
Searching. See Locating
Select Shuffle Play 10
Shuffle Play 9
T
Total playing time 8
Troubleshooting 12
U, V, W, X, Y, Z
Unpacking 4
13
Sony Corporation Printed in Indonesia