Sony DAV-DZ555M User's Manual

2-895-970-E2(1)
DVD Home Theatre
System
Operating Instructions
DAV-DZ555M
©2007 Sony Corporation
Disposal of Old
Electrical & Electronic
Equipment (Applicable
in the European Union
and other European
countries with separate
collection systems)
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
Caution – The use of optical instruments
with this product will increase eye
hazard.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To prevent fire, do not cover the ventilation of the
apparatus with news papers, table-cloths, curtains, etc.
And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Do not expose the battery to excessive heat such as
direct sunlight, fire, or the like.
Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical waste.
This symbol on the product or on
its packaging indicates that this
product shall not be treated as household waste. Instead
it shall be handed over to the applicable collection
point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative
consequences for the environment and human health,
which could otherwise be caused by inappropriate
waste handling of this product. The recycling of
materials will help to conserve natural resources. For
more detailed information about recycling of this
product, please contact your local Civic Office, your
household waste disposal service or the shop where
you purchased the product.
Precautions
On power sources
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
• AC power cord (mains lead) must be changed only at
the qualified service shop.
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet (mains), even if the unit itself has been turned
off.
• Install this system so that the AC power cord (mains)
can be unplugged from the wall socket immediately
in the event of trouble.
Welcome!
Thank you for purchasing Sony DVD Home
Theatre System. Before operating this system,
please read this manual thoroughly and retain it
for future reference.
2GB
Table of Contents
Welcome! ................................................ 2
About This Manual ................................. 5
This System Can Play the Following
Discs ................................................. 5
Getting Started – BASIC –
Step 1: Assembling
the Speakers ............................. 9
Step 2: Connecting the System and
TV ............................................. 14
Step 3: Positioning the System... 18
Step 4: Performing the Quick
Setup........................................ 19
Getting Started
– ADVANCED –
Turning off the Demonstration ............. 22
Installing the Speakers on a Wall.......... 23
Connecting the TV (Advanced) ............24
Connecting Other Components............. 28
Basic Operations
Playing Discs ................................ 30
Enjoying the Radio or Other
Components............................ 31
Enjoying TV or VCR Sound from All
Speakers.................................. 32
Selecting the Movie or Music
Mode ........................................ 33
Sound Adjustments
Enjoying Surround Sound by Using Sound
Field ................................................34
Various Functions for Playing
Discs
Searching for a Particular Point on
a Disc .............................................. 36
(Scan, Slow-motion Play, Freeze
Frame)
Searching for a Title/Chapter/Track/
Scene, etc. ....................................... 37
Searching by Scene ............................... 38
(Picture Navigation)
Resuming Playback from the Point Where
You Stopped the Disc ..................... 38
(Resume Play)
Creating Your Own Program................ 39
(Program Play)
Playing in Random Order ..................... 41
(Shuffle Play)
Playing Repeatedly ............................... 42
(Repeat Play)
Using the DVD’s Menu ........................ 43
Changing the Sound.............................. 43
Selecting [ORIGINAL] or [PLAY LIST]
on a DVD-R/DVD-RW.................. 45
Viewing Information About the Disc ... 46
Changing the Angles ............................ 48
Displaying the Subtitles........................ 48
Adjusting the Delay Between the Picture
and Sound....................................... 49
(A/V SYNC)
About MP3 Audio Tracks and JPEG
Image Files ..................................... 49
Playing DATA CDs or DATA DVDs with
MP3 Audio Tracks and JPEG Image
Files ................................................ 51
Playing Audio Tracks and Images as a
Slide Show with Sound .................. 53
Enjoying DivX® Videos ...................... 55
Playing VIDEO CDs with PBC Functions
(Ver.2.0) ......................................... 57
(PBC Playback)
Tuner Functions
Presetting Radio Stations...................... 58
Listening to the Radio........................... 59
Other Operations
Controlling the TV with the Supplied
Remote ........................................... 61
Using the THEATRE SYNC Function. 61
Enjoying Karaoke ................................. 62
Using the Sound Effect......................... 66
Using the Sleep Timer .......................... 66
Changing the Brightness of the Front
Panel Display.................................. 67
Using the DIGITAL MEDIA PORT
Adapter ........................................... 67
Deactivating the Buttons on the Unit ... 68
(Child Lock)
continued
3GB
Advanced Settings and
Adjustments
Locking Discs ....................................... 69
(CUSTOM PARENTAL
CONTROL, PARENTAL
CONTROL)
Getting Optimal Surround Sound for a
Room .............................................. 72
(SPEAKER FORMATION)
Calibrating the Appropriate Settings
Automatically ................................. 74
(AUTO CALIBRATION)
Using the Setup Display........................ 76
Setting the Display or Sound Track
Language ........................................ 78
[LANGUAGE SETUP]
Settings for the Display......................... 78
[SCREEN SETUP]
Custom Settings .................................... 80
[CUSTOM SETUP]
Settings for the Speakers....................... 81
[SPEAKER SETUP]
Returning to the Default Settings.......... 84
Additional Information
Precautions............................................ 85
Notes about the Discs............................ 86
Troubleshooting .................................... 86
Self-diagnosis Function ........................ 90
(When letters/numbers appear in
the display)
Specifications........................................ 91
Glossary ................................................ 92
Language Code List .............................. 95
Index to Parts and Controls................... 96
Guide to the Control Menu Display...... 99
DVD Setup Display List ..................... 103
System Menu List ............................... 104
Index ...................................................105
4GB
About This Manual
• The instructions in this manual describe the
controls on the remote. You can also use the
controls on the unit if they have the same or
similar names as those on the remote.
• The Control Menu items may vary depending
on the area.
• “DVD” may be used as a general term for
DVD VIDEOs, DVD+RWs/DVD+Rs, and
DVD-RWs/DVD-Rs.
• Measurements are expressed in feet (ft) for
North American models.
• The following symbols are used in this
manual.
Symbol
This System Can Play the
Following Discs
Format of
discs
Disc logo
DVD VIDEO
DVD-RW/
DVD-R
DVD+RW/
DVD+R
Meaning
Functions available for DVD
VIDEOs, DVD-Rs/DVD-RWs in
video mode, and DVD+Rs/
DVD+RWs
Functions available for DVD-Rs/
DVD-RWs in VR (Video
Recording) mode
Functions available for VIDEO
CDs (including Super VCDs or CDRs/CD-RWs in video CD format or
Super VCD format)
Functions available for music CDs
or CD-Rs/CD-RWs in music CD
format
Functions available for DATA CDs
(CD-ROMs/CD-Rs/CD-RWs)
containing MP31) audio tracks,
JPEG image files, and DivX2)3)
video files
Functions available for DATA
DVDs (DVD-ROMs/DVD-Rs/
DVD-RWs/DVD+Rs/DVD+RWs)
containing MP31) audio tracks,
JPEG image files, and DivX2)3)
video files
1)MP3
(MPEG1 Audio Layer 3) is a standard format
defined by ISO/MPEG which compresses audio data.
2)
DivX® is a video file compression technology,
developed by DivX, Inc.
3) DivX,
DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under license.
VIDEO CD
(Ver. 1.1 and
2.0 discs)/
Audio CD
CD-RW/CD-R
(audio data)
(MP3 files)
(JPEG files)
“DVD-RW,” “DVD+RW,” “DVD+R,”
“DVD VIDEO,” and the “CD” logos are trademarks.
Note about CDs/DVDs
The system can play CD-ROMs/CD-Rs/CDRWs recorded in the following formats:
– audio CD format
– VIDEO CD format
– MP3 audio tracks, JPEG image files, and
DivX video files of format conforming to ISO
9660 Level 1/Level 2, or its extended format,
Joliet
continued
5GB
The system can play DVD-ROMs/DVD+RWs/
DVD-RWs/DVD+Rs/DVD-Rs recorded in the
following formats:
– MP3 audio tracks, JPEG image files, and
DivX video files of format conforming to
UDF (Universal Disc Format)
Example of discs that the
system cannot play
The system cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than those
recorded in the formats listed on page 5
• CD-ROMs recorded in PHOTO CD format
• Data part of CD-Extras
• DVD Audios
• Super Audio CD
• DATA DVDs that do not contain MP3 audio
tracks, JPEG image files, or DivX video files
• DVD-RAMs
Music discs encoded with
copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
About Multi Session CD
Also, the system cannot play the following
discs:
• A DVD VIDEO with a different region code
(page 6, 94)
• A disc that has a non-standard shape (e.g.,
card, heart)
• A disc with paper or stickers on it
• A disc that has the adhesive of cellophane tape
or a sticker still left on it
Notes about CD-R/CD-RW/DVD-R/
DVD-RW/DVD+R/DVD+RW
In some cases, CD-R/CD-RW/DVD-R/DVDRW/DVD+R/DVD+RW cannot be played on
this system due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software.
The disc will not play if it has not been correctly
finalized. For more information, see the
operating instructions for the recording device.
Note that some playback functions may not
work with some DVD+RWs/DVD+Rs, even if
they have been correctly finalized. In this case,
view the disc by normal playback. Also some
DATA CDs/DATA DVDs created in Packet
Write format cannot be played.
6GB
• This system can play Multi Session CDs when
an MP3 audio track is contained in the first
session. Any subsequent MP3 audio tracks
recorded in later sessions can also be played
back.
• This system can play Multi Session CDs when
a JPEG image file is contained in the first
session. Any subsequent JPEG image files
recorded in later sessions can also be played
back.
• If audio tracks and images in music CD format
or video CD format are recorded in the first
session, only the first session will be played
back.
Region code
Your system has a region code printed on the
rear of the unit and will only play DVDs labeled
with the same region code.
DVD VIDEOs labeled ALL will also play on this
system.
If you try to play any other DVD VIDEO, the
message [Playback prohibited by area
limitations.] will appear on the TV screen.
Depending on the DVD VIDEO, no region code
indication may be given even though playing the
DVD VIDEO is prohibited by area restrictions.
Note about playback
operations of DVDs and
VIDEO CDs
Some playback operations of DVDs and VIDEO
CDs may be intentionally set by software
producers. Since this system plays DVDs and
VIDEO CDs according to the disc contents the
software producers designed, some playback
features may not be available. Be sure to read the
operating instructions supplied with the DVDs
or VIDEO CDs.
Copyrights
This product incorporates copyright protection
technology that is protected by U.S. patents and
other intellectual property rights. Use of this
copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
This system incorporates with Dolby* Digital
and Dolby Pro Logic (II) adaptive matrix
surround decoder and the DTS** Digital
Surround System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
** Manufactured under license from DTS, Inc.
“DTS” and “DTS Digital Surround” are registered
trademarks of DTS, Inc.
7GB
Getting Started – BASIC –
Getting Started – BASIC –
See Unpacking in Specifications, page 91.
Inserting batteries into the remote
You can control the system using the supplied remote. Insert two R6 (size AA) batteries by matching
the 3 and # ends on the batteries to the markings inside the compartment. To use the remote, point it
at the remote sensor on the unit.
Note
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.
• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
Attaching the foot pads to the subwoofer
Attach the supplied foot pads to the bottom of the subwoofer to stabilize the subwoofer and prevent it
from slipping.
8GB
Step 1: Assembling the Speakers
Getting Started – BASIC –
Before connecting the speakers, attach the speaker stand to the speaker.
(For the front speakers.)
About how to connect the speaker cords to the SPEAKER jacks, see page 15.
Note
• Spread a cloth on the floor to avoid damaging the floor.
Tip
• You can use the speaker without the speaker stand by installing it on the wall (page 23).
Use the screws illustrated below.
Screw (small, black)
1
Screw (small, silver)
Screw (large, with
washer)
Thread the speaker cord through the hole on the base and post.
Be careful with the orientation of the post. Thread the speaker cord into the end of the post that has
2 holes.
About the speaker cord
The connector and color tube of the speaker cords are the same color as the label of the jacks to be
connected.
Use the speaker cords as follows:
• Front speaker (L): White
• Front speaker (R): Red
Post
Bottom of the base
2 holes
,
Speaker cord
Top of the base
continued
9GB
2
Attach the post cover to the other end of the post.
Getting Started – BASIC –
Orient the slot toward you, attach the post cover so that the slot of the post engages with the tab of
the post cover, then secure with the screw.
Thread the speaker cord through
the hole of the post cover.
Speaker cord
,
,
Hole
Post cover
Upper part of the
post
Screw (small, black)
3
Lay the post in the slot of the speaker, slide the post to the end of the slot, then secure
the post with the mounting plate and screws.
Select the speaker whose color of the jack on the rear panel of speaker matches the color tube of
the speaker cord.
Post cover
Be careful the
orientation of the
post cover when
placing the post.
Secure 2 screws (large, with
washer) in criss-cross pattern.
,
Rear of the speaker
Mounting plate
When securing the mounting plate, position the mounting plate depending on the desired height of
the speaker.
Low position
High position
After attaching the post to the base, you can adjust the height of the speaker.
10GB
4
Connect the speaker cords to the speaker.
Color tube
Front speaker (L): White
Front speaker (R): Red
Rear of the speaker
5
Attach the post to the base.
Insert the post so that the slit on the lower part of the post aligns with the projection of the base,
then secure the post with the 2 screws.
Post
Slit
,
Projection
Base
Screws
(small, silver)
Note
• Make sure that the slot on the post aligns with the projection of the base by rotating the post slightly.
continued
11GB
Getting Started – BASIC –
Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and #
to #.
6
Adjust the height of the speaker.
Getting Started – BASIC –
Loosen (but do not remove) the screws, adjust the height of the speaker, then secure the screws.
Adjust the speaker of one side, then adjust another speaker by checking lines as a guide.
Note
• When adjusting the height of the speaker, grasp the speaker so that the speaker does not fall.
Lines
,
Post
In addition to the screws
secured in Step 3, secure
2 more screws. (Secure 4
screws in total.)
Loosen 2 screws.
7
Take up any speaker cord slack.
Take up slack in the speaker cord by pulling from the bottom of the base.
Secure the speaker cord by
running it through the slot.
Adjust the length of the cord.
12GB
Fully-assembled illustration
White
Front speaker (R):
Red label
Getting Started – BASIC –
Front speaker (L):
White label
Red
13GB
Getting Started – BASIC –
Step 2: Connecting the System and TV
The following is the basic connection of the unit to the speakers and TV. For other TV connections, see
page 24. For other component connection, see page 28.
To accept progressive signals, see page 26.
Refer to the connection diagram below, and read the additional information from 1 to 4 on the
following pages.
Front speaker (L)
Front speaker (R)
Center speaker
AM loop antenna (aerial)
SPEAKER
FRONT R
CENTER
FRONT L
SUR R
COAXIAL
SUR L
AM
DMPORT
TV /
VIDEO
DIR-TC1
SPEAKER
FM75
R AUDIO IN L
VIDEO
WOOFER
(DVD ONLY)
OUT
(DVD ONLY)
S VIDEO
Y
P B/C B
P R/C R
COMPONENT VIDEO OUT
(DVD ONLY)
MONITOR OUT
AC power cord (mains lead)
A
B
AUDIO
OUT
FM wire antenna
(aerial)
VIDEO
IN
L
R
TV
Subwoofer
Surround speaker (L)
Surround speaker (R)
:Signal flow
14GB
1 Connecting the Speakers
The connector and color tube of the speaker cords are the same color as the label of the jacks to be
connected.
To the SPEAKER jack
Color tube
(+)
(–)
Note
• Do not catch the speaker cord insulation in the SPEAKER jack.
To avoid short-circuiting the speakers
Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these
precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch
another speaker terminal or the bare wire of another speaker cord, such as shown below.
Stripped speaker cord is touching
another speaker terminal.
Stripped cords are touching each other
due to excessive removal of insulation.
After connecting all the components, speakers, and AC power cord (mains lead), output a test tone to
check that all the speakers are connected correctly. For details on outputting a test tone, see page 83.
If no sound is heard from a speaker while outputting a test tone, or a test tone is output from a speaker
other than the one currently displayed on the Setup Display, the speaker may be short-circuited. If this
happens, check the speaker connection again.
Note
• Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and # to #. If the cords
are reversed, the sound will lack bass and may be distorted.
continued
15GB
Getting Started – BASIC –
Required cords
Getting Started – BASIC –
2 Connecting the TV
Required cords
A Video cord
.
Yellow
B Audio cord (not supplied)
White (L/audio)
Red (R/audio)
Tip
• When you want to output the TV sound or stereo sound of a 2 channel source from the 6 speakers, select the “Dolby
Pro Logic,” “Dolby Pro Logic II MOVIE,” or “Dolby Pro Logic II MUSIC” sound field (page 34).
3 Connecting the Antenna (Aerial)
To connect the AM loop antenna (aerial)
The shape and the length of the antenna (aerial) is designed to receive AM signals. Do not dismantle
or roll up the antenna (aerial).
1
2
3
Remove only the loop part from the plastic stand.
Set up the AM loop antenna (aerial).
Connect the cords to the AM antenna (aerial) terminals.
Cord (A) or cord (B) can be connected to either terminal.
Insert the cord pushing
down the terminal clamp.
A
B
Insert until this
part.
Note
• Do not place the AM loop antenna (aerial) near the unit or other AV equipment, as noise may result.
Tip
• Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.
4
Make sure the AM loop antenna (aerial) is connected firmly by pulling softly.
16GB
To connect the FM wire antenna (aerial)
Connect the FM wire antenna (aerial) to the COAXIAL FM 75 Ω jack.
Getting Started – BASIC –
FM wire antenna (aerial)
(supplied)
FM wire antenna (aerial)
(supplied)
or
COAXIAL FM 75 Ω jack
COAXIAL FM 75 Ω jack
Note
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM
antenna (aerial) as shown below.
Unit
Outdoor FM antenna (aerial)
4 Connecting the AC power cord (mains lead)
Before connecting the AC power cord (mains lead) of this unit to a wall outlet (mains), connect the
speakers to the unit.
17GB
Getting Started – BASIC –
Step 3: Positioning the
System
Positioning the speakers
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position (A).
However, this system allows you to place the
center speaker up to 1.6 meters (5 ft) closer (B)
and the surround speakers up to 5.0 meters (16
ft) closer (C) to the listening position.
The front speakers can be placed from 1.0 to
7.0 meters (3 to 23 ft) (A) from the listening
position.
Place speakers as illustrated below.
Note
• Do not set the speakers in an inclined position.
• Do not place the speakers in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight
• Use caution when placing the speakers and/or
speaker stands that are attached with the speakers on
a specially treated (waxed, oiled, polished, etc.) floor,
as staining or discoloration may result.
• When cleaning, use a soft cloth such as a cleaning
cloth for glasses.
• Do not use any type of abrasive pad, scouring
powder, or solvent such as alcohol or benzine.
18GB
• Do not lean or hang on the speaker, as the speaker
may fall down.
Tip
• When you change the positions of the speakers, it is
recommended that you change the settings. For
details, see “Getting Optimal Surround Sound for a
Room” (page 72) and “Calibrating the Appropriate
Settings Automatically” (page 74).
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
FRENCH
SPANISH
PORTUGUESE
Follow the steps below to make the minimum
number of basic adjustments for using the
system.
"/1
5
Press X/x to select a language.
The system displays the menu and subtitles
in the selected language.
6
Press
.
The Setup Display for selecting the aspect
ratio of the TV to be connected appears.
SCREEN SETUP
TV TYPE:
YCBCR/RGB (HDMI):
SCREEN SAVER:
BACKGROUND:
4:3 OUTPUT:
C/X/x/c,
DISPLAY
1
2
Turn on the TV.
7
Press [/1.
4
[16:9] (page 78)
x If you have a 4:3 standard TV
Switch the input selector on your TV so
that the signal from the system
appears on the TV screen.
[Press [ENTER] to run QUICK SETUP.]
appears at the bottom of the TV screen. If
this message does not appear, recall the
Quick Setup display (page 21) and perform
again.
Press
without inserting a disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
Press X/x to select the setting that
matches your TV type.
x If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
Note
• Make sure that the function is set to “DVD”
(page 30).
3
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
FULL
[4:3 LETTER BOX] or [4:3 PAN SCAN]
(page 78)
8
Press
.
The Setup Display for selecting the speaker
formation appears.
9
Press C/c to select the speaker
formation image as the speakers are
actually positioned.
For details, see “Getting Optimal Surround
Sound for a Room” (page 72).
SPEAKER FORMATION
STANDARD
continued
19GB
Getting Started – BASIC –
Step 4: Performing the
Quick Setup
12 Press
Getting Started – BASIC –
Note
• When the wireless kit WAHT-SD1 (not
supplied) is installed, [STANDARD
(WIRELESS)] appears instead.
.
AUTO CALIBRATION
Connect calibration mic. Start
measurement?
10 Press .
11 Connect the calibration mic to the
YES
NO
A.CAL MIC jack on the front panel and
press X/x to select [YES].
Set up the calibration mic at the ear level
using a tripod, etc. (not supplied). The front
of each speaker should face the calibration
mic, and there should be no obstruction
between the speakers and the calibration
mic. Be quiet during the measurement.
AUDIO IN / MIC 1 /
A.CAL MIC
Auto Calibration starts.
Note
• Loud test sound is output when [AUTO
CALIBRATION] starts. You cannot turn the
volume down. Give consideration to children
and neighbor.
• Avoid being in the measurement area and
making noise during the measurement (which
takes about 3 minutes), as it may interfere with
measurement.
13 Unplug the calibration mic and press C/
c to select [YES].
Calibration mic
Measurement complete.
FRONT L :
YES
FRONT R :
YES
CENTER :
NONE
SUBWOOFER : YES
SURROUND L : NONE
SURROUND R : NONE
If OK, unplug calibration mic and select
“YES”.
YES
NO
Note
• The environment of the room in which the
system is installed may affect measurements.
• If measurement fails, follow the message then
retry [AUTO CALIBRATION].
• When you select [SECOND ROOM] for
[SPEAKER FORMATION], measurement of
[SURROUND L] and [SURROUND R] is not
displayed.
14 Press
.
Quick Setup is finished. All connections
and setup operations are complete.
To quit the Quick Setup
Press
DISPLAY in any Step.
Tip
• If you change the position of the speakers, reset the
speaker settings. See “Getting Optimal Surround
Sound for a Room” (page 72) and “Calibrating the
Appropriate Settings Automatically” (page 74).
20GB
• If you want to change any of the settings, see “Using
the Setup Display” (page 76).
1
Getting Started – BASIC –
To recall the Quick Setup display
Press
DISPLAY when the system is in
stop mode.
The Control Menu display appears.
2
Press X/x to select
press
.
[SETUP], then
The options for [SETUP] appear.
12(27)
18(34)
T
0:00:02
DVD VIDEO
QUICK
QUICK
CUSTOM
RESET
BNR
3
Press X/x to select [QUICK], then press
.
The Quick Setup display appears.
21GB
Getting Started – ADVANCED –
Setting the demonstration
mode to on/off
1
2
Turning off the
Demonstration
3
"/1
X/x/c,
Press X/x repeatedly until “DEMO”
appears in the front panel display, then
press
or c.
Press X/x to select a setting.
The default setting is underlined.
• “DEMO ON”: sets the demonstration
mode to on.
• “DEMO OFF”: sets the demonstration
mode to off.
4
SYSTEM
MENU
Press SYSTEM MENU.
Press
.
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
After connecting the AC power cord (mains
lead), the demonstration appears in the front
panel display. When you press "/1 on the
remote, the demonstration turns off.
Note
• When you press "/1 on the unit, the demonstration
does not turn off.
• When you set the demonstration mode in the system
menu to on, the demonstration does not turn off even
though you press "/1 on the remote. To turn off the
demonstration, set the demonstration mode to off,
then press "/1 on the remote. When the
demonstration mode is set to off, the system saves
power in standby mode.
• If the system is at its factory default settings (ex. after
performing “COLD RESET” (page 84)), you can turn
off the demonstration simply by pressing "/1 on the
remote. Otherwise, to stop the demonstration, you
need to set “DEMO” to “DEMO OFF.”
22GB
For the front speakers
Installing the Speakers on
a Wall
100 mm
(3 15/16 inches)
6 to 9 mm
(1/4 to 3/8 inch)
Installing the speakers on a
wall
1
Prepare screws (not supplied) that are
suitable for the hole on the back of
each speaker. See the illustrations
below.
For the other speakers
4 mm (5/32 inch)
30 mm (1 3/16 inches)
4.6 mm
(3/16 inch)
6 to 9 mm
(1/4 to 3/8 inch)
Hole on the back of
the speaker
3
10 mm
(13/32 inch)
2
Getting Started – ADVANCED –
You can use the speakers by installing on the
wall.
Hang the speakers on the screws.
4.6 mm
(3/16 inch)
10 mm
(13/32 inch)
Fasten the screws to the wall.
For the center speaker
160 mm
(6 5/16 inches)
Rear of speaker
7 to 9 mm
(9/32 to 3/8 inch)
Note
• Use screws that are suitable for the wall material and
strength. As a plaster board wall is especially fragile,
attach the screws securely to a beam and fasten them
to the wall. Install the speakers on a vertical and flat
wall where reinforcement is applied.
• Contact a screw shop or installer regarding the wall
material or screws to be used.
• Sony is not responsible for accident or damage
caused by improper installation, insufficient wall
strength or improper screw installation, natural
calamity, etc.
23GB
Connecting the TV (Advanced)
Sends the played back DVD image to the connected TV.
Check the jacks of your TV, and choose connection method A, B, C, or D. Picture quality improves
in order from A (standard) to D (HDMI).
D
TV with HDMI* IN jack
IN
To VIDEO
To HDMI* OUT
SPEAKER
FRONT R
FRONT L
SUR R
COAXIAL
SUR L
DIR-TC1
SPEAKER
CENTER
AM
DMPORT
FM75
R AUDIO IN L
TV /
VIDEO
VIDEO
WOOFER
(DVD ONLY)
OUT
(DVD ONLY)
S VIDEO
Y
P B/C B
P R/C R
COMPONENT VIDEO OUT
Y
B
MONITOR OUT
To
S VIDEO
To COMPONENT
VIDEO OUT
C
(DVD ONLY)
A
S VIDEO
IN
VIDEO
IN
PB/CB
PR/CR
TV with COMPONENT
VIDEO IN jacks
TV with S VIDEO IN jack
TV with VIDEO IN jack
:Signal flow
* HDMI (high-definition multimedia interface)
The system incorporates High-Definition Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
24GB
A To connect to a TV with the VIDEO IN jack
Connect the video cord.
.
Yellow
Connect an S video cord (not supplied). To use the S video jack instead of the video jack, your TV
monitor must also be connected via an S video jack. S video signals are on a separate bus from the video
signals and will not be output through the video jack.
C To connect to a TV with the COMPONENT VIDEO IN jacks
Connect a component video cord (not supplied). To use the COMPONENT VIDEO OUT jacks (Y, PB/
CB, PR/CR) instead of the video jack, your TV monitor must be equipped with via COMPONENT
VIDEO IN jacks (Y, PB/CB, PR/CR). If your TV accepts progressive format signals, you must use this
connection and set the output channel of the system to progressive format (page 26).
Getting Started – ADVANCED –
B To connect to a TV with the S VIDEO IN jack
Green
Blue
Red
D To connect to a TV with the HDMI (high-definition multimedia
interface)/DVI (digital visual interface) IN jack
Use a certified HDMI (high-definition multimedia interface) cord (not supplied) to enjoy high quality
digital picture and sound through the HDMI OUT (high-definition multimedia interface out) jack.
To connect to a TV with DVI (digital visual interface) input
Use an HDMI (high-definition multimedia interface)-DVI (digital visual interface) converter cord (not
supplied) with an HDMI (high-definition multimedia interface)-DVI (digital visual interface) adaptor
(not supplied). The DVI (digital visual interface) jack will not accept any audio signals. Furthermore,
you cannot connect the HDMI OUT (high-definition multimedia interface out) jack to DVI (digital
visual interface) jacks that are not HDCP (high-bandwidth digital content protection) compliant (e.g.,
DVI (digital visual interface) jacks on the computer displays).
To select the type of video signal output from the HDMI OUT (highdefinition multimedia interface out) jack
When you connect the unit and the TV with the HDMI cord, selects the type of video signals output
from the HDMI OUT (high-definition multimedia interface out) jack.
For details, refer also to the operating instructions supplied with the TV/projector, etc.
1
2
Press FUNCTION repeatedly to select “DVD.”
Press VIDEO FORMAT.
The current type of video signals appears in the front panel display.
Each time you press VIDEO FORMAT, the display changes as follows:
continued
25GB
t 720 × 480p*
r
1280 × 720p*
r
720 × 480p*
r
1920 × 1080i*
• “720 × 480p*”: Sends 720 × 480p video signals.**
• “1280 × 720p*”: Sends 1280 × 720p video signals.
• “1920 × 1080i*”: Sends 1920 × 1080i video signals.
*i: interlace, p: progressive
**Depending on the country, [720 × 576p] may appear.
Note
• When the HDMI indicator on the front panel lights up, images other than [720 × 480p] or [720 × 576p] are stretched
vertically.
When connecting to a standard 4:3 screen TV
Depending on the disc, the image may not fit your TV screen.
To change the aspect ratio, see page 78.
Does your TV accept progressive signals?
Progressive is the method for displaying TV images which reduces flickering, and sharpens the image.
To display using this method, you need to connect to a TV that accepts progressive signals.
FUNCTION
VIDEO
FORMAT
“PROGRE” lights up in the front panel display when the system outputs progressive signals.
1
2
Press FUNCTION repeatedly to select “DVD.”
Press VIDEO FORMAT.
The current signal appears in the front panel display.
Each time you press VIDEO FORMAT, the display changes as follows:
26GB
t NORMAL (INTERLACE)
r
PROGRESSIVE
x NORMAL (INTERLACE)
x PROGRESSIVE
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT VIDEO OUT jacks.
Normally select this under the above condition. This automatically detects the software type, and
selects the appropriate conversion method.
Note that the picture will not be clear or no picture will appear if you select these settings when
either of the above conditions are not met.
Getting Started – ADVANCED –
Select this setting when:
– your TV does not accept progressive signals, or,
– your TV is connected to jacks other than the COMPONENT VIDEO OUT jacks (MONITOR
OUT (VIDEO/S VIDEO)).
Note
• When you connect the unit and the TV with the HDMI cord during the system is set to “NORMAL
(INTERLACE),” the system is set to “PROGRESSIVE” automatically.
Tip
• When you connect the unit and the TV with the HDMI cord, VIDEO FORMAT is used for selecting the type of
video signals output from the HDMI OUT jack. For details, see “To select the type of video signal output from the
HDMI OUT (high-definition multimedia interface out) jack” (page 25).
About DVD software types and the conversion method
DVD software can be divided into 2 types: film-based software and video-based software.
Video-based software is derived from TV, such as dramas and sit-coms, and displays images at 30
frames/60 fields per second. Film-based software is derived from film and displays images at 24 frames
per second. Some DVD software contains both video and film.
In order for these images to appear natural on your screen when output in progressive format, the
progressive signals need to be converted to match the type of DVD software that you are watching.
Note
• When you play video-based software in progressive signal format, sections of some types of images may appear
unnatural due to the conversion process when output through the COMPONENT VIDEO OUT jacks. Even though
you set to “PROGRESSIVE,” images from the MONITOR OUT (VIDEO or S VIDEO) jack are unaffected as they
are output in the interlace format.
27GB
Connecting Other Components
You can enjoy sound using the speakers of this system by connecting the AUDIO OUT jacks of another
component. For video connection of other components, connect directly to the TV.
DIGITAL MEDIA
PORT adapter
Screws*
DIR-TC1 slot for
the WAHT-SD1
To DMPORT jack
SPEAKER
FRONT R
FRONT L
SPEAKER
CENTER
SUR R
COAXIAL
SUR L
AM
DMPORT
TV /
VIDEO
DIR-TC1
FM75
R AUDIO IN L
VIDEO
WOOFER
(DVD ONLY)
OUT
(DVD ONLY)
S VIDEO
Y
P B/C B
P R/C R
COMPONENT VIDEO OUT
(DVD ONLY)
MONITOR OUT
To TV/VIDEO
(AUDIO IN)
AUDIO
OUT
L
R
VCR, digital satellite receiver
or PlayStation, etc.
*
:Signal flow
CAUTION
Please do not remove the screws before installing the WAHT-SD1.
To connect the AUDIO OUT jacks of other components to the TV/VIDEO
(AUDIO IN) jacks of this unit
Connect the VCR or other components to the TV/VIDEO (AUDIO IN) jacks using the audio cord (not
supplied). When connecting a cord, be sure to match the color-coded sleeves to the appropriate jacks
on the components.
White (L/audio)
Red (R/audio)
To connect the DIGITAL MEDIA PORT adapter
Connect a DIGITAL MEDIA PORT adapter (not supplied) to the DMPORT jack. For details of the
DIGITAL MEDIA PORT adapter, see “Using the DIGITAL MEDIA PORT Adapter” (page 67).
28GB
To listen to the portable audio source sound through the system
Connect the audio output jacks of the portable audio source to the AUDIO IN jack on the front panel
of the unit with the stereo mini-plug cord (not supplied).
Wireless system option
When you install the WAHT-SD1 (not supplied) in the DIR-TC1 slot, you can enjoy wireless
performance by transmission of the sound to the surround speakers. For details, see the operating
instructions of the WAHT-SD1.
Note
• Be sure to make connections securely to avoid hum and noise.
• When you connect another component with a volume control, turn up the volume of the other components to a level
where sound is not distorted.
Getting Started – ADVANCED –
Tip
• When listening to MP3 format recordings using a portable audio source, you can enhance the sound.
Press FUNCTION to select “AUDIO.” Connect the portable audio source. Press SOUND FIELD repeatedly until
“A.F.D. STD” appears in the front panel display.
To cancel, select other than “A.F.D. STD.”
29GB
Basic Operations
Basic Operations
Playing Discs
"/1
A
Disc tray
Z
H FUNCTION
Adjust the
volume
Note
• When you play an 8 cm disc, place it on the
inner circle of the tray. Be careful that the disc is
not skewed on the inner circle of the tray.
• Do not forcibly press the disc tray closed with
your finger, as this may cause malfunction.
• Do not place more than one disc on the tray.
6
Press H.
The system starts playback (continuous
play).
Adjust the volume on the unit.
The volume level appears on the TV screen
and in the front panel display.
"/1
FUNCTION
Note
MUTING
VOLUME +/–
./>
/
H
x
X
Depending on the DVD VIDEO or VIDEO CD,
some operations may be different or restricted.
Refer to the operating instructions supplied with
your disc.
1
2
3
Turn on your TV.
Switch the input selector on the TV to
this system.
Press "/1.
The system turns on.
Unless the system is set to “DVD,” press
FUNCTION to select “DVD.”
4
5
Press A.
Load a disc.
Place one disc on the tray, and then press A.
30GB
• Depending on the system status, the volume level
may not appear on the TV screen.
• When you set the HDMI CONTROL function to on
(page 80), the TV that is connected to the system with
the HDMI cord can be synch-operated with the
system. For details, see the HDMI CONTROL Guide
(supplied separately).
Tip
• When you connect the system and TV with the HDMI
cord, you can operate them simply, using the HDMI
CONTROL function. For details, see the HDMI
CONTROL Guide (supplied separately).
To save the power in standby
mode
Press "/1 while the system turns on. To cancel
standby mode, press "/1 once.
Additional operations
To
Press
Stop
x
Pause
X
Resume play after pause
X or H
Go to the next chapter,
track, or scene
> (except for JPEG)
Press
Go back to the preceding
chapter, track, or scene
. (except for JPEG)
Turn off the sound
temporarily
MUTING. To cancel,
press it again or
VOLUME + to adjust
the sound volume.
Stop play and remove the
disc
Z on the remote or A
on the unit.
Replay the previous scene*
(instant
replay) during
playback.
Briefly fast forward the
current scene**
(instant
advance) during
playback.
* DVD VIDEOs/DVD-RWs/DVD-Rs only. The
button can be used except for DivX video files.
** DVD VIDEOs/DVD-RWs/DVD-Rs/DVD+RWs/
DVD+Rs only. The button can be used except for
DivX video files.
Enjoying the Radio or
Other Components
FUNCTION
SYSTEM
MENU
X/x/c,
Note
• You may not be able to use the instant replay or
instant advance function with some scenes.
Selecting the connected
component
You can use a VCR or other components
connected to the TV/VIDEO jacks on the rear
panel. Refer to the operating instructions
supplied with the components for further
information.
Press FUNCTION repeatedly until “TV/
VIDEO” appears in the front panel display.
Each time you press FUNCTION, the mode of
the system changes in the following sequence.
DVD t TUNER FM t TUNER AM t
TV/VIDEO t DMPORT t AUDIO t …
continued
31GB
Basic Operations
To
Basic Operations
Changing the input level of
the sound from connected
components
Distortion may occur when listening to a
component connected to the TV/VIDEO jacks
on the rear panel or to the AUDIO IN jack on the
front panel. This is not a malfunction and will
depend on the component connected.
To prevent this, you can change the input level
from the sound of the other components.
1
2
3
4
Enjoying TV or VCR Sound
from All Speakers
You can enjoy TV or VCR sound from all the
speakers in this system.
For details, see “Step 2: Connecting the System
and TV” (page 14), “Connecting the TV
(Advanced)” (page 24), and “Connecting Other
Components” (page 28).
Press FUNCTION repeatedly until “TV/
VIDEO” or “AUDIO” appears in the
front panel display.
FUNCTION
Press SYSTEM MENU.
SOUND
FIELD
Press X/x repeatedly until
“ATTENUATE” appears in the front
panel display, then press
or c.
Press X/x to select a setting.
The default setting is underlined.
• “ATT ON”: attenuates the input level.
The output level is changed.
• “ATT OFF”: normal input level.
5
Press
.
The setting is made.
6
1
Press SYSTEM MENU.
The system menu turns off.
2
Press FUNCTION repeatedly until “TV/
VIDEO” appears in the front panel
display.
Press SOUND FIELD repeatedly until
the sound field you want appears in the
front panel display.
When you want to output the TV sound or
stereo sound of a 2 channel source from the
6 speakers, select the “PRO LOGIC,” “PLII
MOVIE,” or “PLII MUSIC” sound field.
For details of sound field, see page 34.
Note
• When you set the [HDMI CONTROL] setting in
[CUSTOM SETUP] to [ON] (page 80), the System
Audio Control function is activated and no sound
may be output from the TV. For details of the System
Audio Control function, see the HDMI CONTROL
Guide (supplied separately).
32GB
Selecting the Movie or
Music Mode
You can choose a suitable sound mode for
movies or music.
Basic Operations
MOVIE/
MUSIC
Press MOVIE/MUSIC during playback.
Press MOVIE/MUSIC repeatedly until the
mode you want lights up in the front panel
display. The default setting is underlined.
• AUTO: selects the mode automatically to
produce the sound effect depending on the
disc.
• MOVIE: provides the sound for movies.
• MUSIC: provides the sound for music.
Tip
• When the movie or music mode is selected,
“MOVIE” or “MUSIC” is displayed in the front panel
display. When neither “MOVIE” or “MUSIC” is
displayed in the front panel display, “AUTO” is
selected.
33GB
Automatic outputting of the
original sound
Sound Adjustments
Enjoying Surround Sound
by Using Sound Field
You can take advantage of surround sound
simply by selecting one of the system’s preprogrammed sound fields. They bring exciting
and powerful sound of movie theaters into your
home.
x AUTO FORMAT DIRECT STANDARD
The auto decoding function automatically
detects the type of audio signal being input
(Dolby Digital, DTS, or standard 2 channel
stereo) and performs the proper decoding if
necessary. This mode presents the sound as it
was recorded/encoded, without adding any
effects (e.g. reverberation).
However, if there are no low frequency signals
(Dolby Digital LFE, etc.), it will generate a low
frequency signal for output to the subwoofer.
Outputting the sound from
multiple speakers
SOUND
FIELD
x AUTO FORMAT DIRECT MULTI
This mode lets you enjoy audio playback of all
types of discs from multiple speakers.
Note
• The sound is not output from multiple speakers
depending on the source.
Outputting 2 channel sources
like CDs by 5.1channel
Press SOUND FIELD.
x Dolby Pro Logic
Press SOUND FIELD repeatedly until the sound
field you want appears in the front panel display.
Dolby Pro Logic produces five output channels
from 2 channel sources. This mode performs Pro
Logic decoding to the input signal and output to
front, center, and surround speakers.
Meanwhile, the surround channel becomes
monaural.
All sound field
Sound field
Display
AUTO FORMAT DIRECT
STANDARD
A.F.D. STD
AUTO FORMAT DIRECT
MULTI
A.F.D. MULTI
x Dolby Pro Logic II MOVIE/MUSIC
Dolby Pro Logic
PRO LOGIC
Dolby Pro Logic II MOVIE
PLII MOVIE
Dolby Pro Logic II MUSIC
PLII MUSIC
2 CHANNEL STEREO
2CH STEREO
Dolby Pro Logic II produces five full-bandwidth
output channels from 2 channel sources. This is
done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
Note
• When the input signal is multi channel source, Dolby
Pro Logic and Dolby Pro Logic II MOVIE/MUSIC
are canceled and the multi channel source is output
directly.
34GB
• When the bilingual broadcast sound is input, Dolby
Pro Logic and Dolby Pro Logic II MOVIE/MUSIC
are not effective.
Using only the front speaker
and subwoofer
x 2 CHANNEL STEREO
To turn the surround effect off
Press SOUND FIELD repeatedly until “A.F.D.
STD” or “2CH STEREO” appears in the front
panel display.
Sound Adjustments
This mode outputs the sound from the front left
and right speakers and subwoofer. Standard 2
channel (stereo) sources completely bypass the
sound field processing. Multi channel surround
formats are downmixed to two channels.
This allows you to play any source using only
the front left and right speakers and subwoofer.
35GB
With each press, playback speed becomes faster.
Various Functions for Playing Discs
Searching for a Particular
Point on a Disc
(Scan, Slow-motion Play, Freeze
Frame)
You can quickly locate a particular point on a
disc by monitoring the picture or playing back
slowly.
Note
• Depending on the DVD/DivX video/VIDEO CD, you
may not be able to do some of the operations
described.
Locating a point quickly by
playing a disc in fast forward
or fast reverse (Scan)
(Except for JPEG)
Press /m or M/ while playing a disc.
When you find the point you want, press H to
return to normal speed. Each time you press /
m or M/ during scan, the playback speed
changes. With each press the indication changes
as shown below. Actual speeds may differ with
some discs.
Playback direction
×2B t 1M t 2M t 3M
3M (DVD VIDEO/DVD-VR mode/DivX video/
VIDEO CD only)
×2B (DVD VIDEO/CD only)
Opposite direction
×2b t 1m t 2m t 3m
3m (DVD VIDEO/DVD-VR mode/DivX video/
VIDEO CD only)
×2b (DVD VIDEO only)
36GB
Watching frame by frame
(Slow-motion Play)
(DVD VIDEO, DVD-R, DVD-RW, DivX
video, VIDEO CD only)
Press /m or M/ when the system is in
pause mode. To return to normal playback
speed, press H. Each time you press /m or
M/ during Slow-motion Play, the playback
speed changes. Two speeds are available. With
each press the indication changes as follows:
Playback direction
2
y1
Opposite direction (DVD VIDEO only)
2
y1
Playing one frame at a time
(Freeze Frame)
(DVD VIDEO, DVD-R, DVD-RW, DivX
video, VIDEO CD only)
When the system is in the pause mode, press
(step) to go to the next frame. Press
(step) to go to the preceding frame
(DVD VIDEO/DVD-R/DVD-RW only). To
return to normal playback, press H.
Note
• You cannot search for a still picture on a DVD-R/
DVD-RW in VR mode.
• For DATA CDs/DATA DVDs, this function works
only for DivX video files.
Searching for a Title/
Chapter/Track/Scene,
etc.
1
Press
DISPLAY. (When playing a
DATA CD/DATA DVD with JPEG image
files, press
DISPLAY twice.)
The Control Menu display appears.
2
Press
[** (**)] changes to [– – (**)].
12(27)
(34)
T
1:32:55
4
[TITLE], [TRACK], [SCENE]
[CHAPTER], [INDEX]
If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
5
Press
To search for a scene using the
time code (DVD VIDEO and
DVD-VR mode only)
1
In Step 2, select
[TIME/TEXT].
[T **:**:**] (playing time of the current title)
is selected.
2
[TRACK]
Press
.
[T **:**:**] changes to [T --:--:--].
3
[ALBUM]
[FILE]
Example: when you select
[CHAPTER]
[** (**)] is selected (** refers to a number).
The number in parentheses indicates the
total number of titles, chapters, tracks,
indexes, scenes, albums or files.
12(27)
18(34)
T
1:32:55
.
The system starts playback from the
selected number.
[TIME/TEXT]
Select [TIME/TEXT] to search for a
starting point by inputting the time code.
DVD VIDEO
Press X/x or the number buttons to
select the title, chapter, track, index,
scene, etc., number you want to search
for.
Press X/x to select the search method.
The display will show different items
depending on the disc.
.
Various Functions for Playing Discs
You can search a DVD by title or chapter, and
you can search a VIDEO CD/CD/DATA CD/
DATA DVD by track, index, or scene. As titles
and tracks are assigned unique numbers on the
disc, you can select the desired one by entering
its number. Or, you can search for a scene using
the time code.
3
DVD VIDEO
Input the time code using the number
buttons, then press
.
For example, to find the scene at 2 hours, 10
minutes, and 20 seconds after the beginning,
just enter [2:10:20].
Tip
• When the Control Menu display is turned off, you can
search for a chapter (DVD VIDEO/DVD-R/DVDRW), track (VIDEO CD/CD), or file (DATA CD/
DATA DVD (DivX video)) by pressing the number
buttons and
.
Note
• You cannot search for a scene on a DVD+RW using
the time code.
Selected row
37GB
Searching by Scene
(Picture Navigation)
You can divide the TV screen into 9 subscreens
and find the desired scene quickly.
1
Resuming Playback from
the Point Where You
Stopped the Disc
(Resume Play)
Press PICTURE NAVI during playback.
The following display appears.
CHAPTER VIEWER
2
ENTER
Press PICTURE NAVI repeatedly to
select an item.
When you stop the disc, the system remembers
the point where you pressed x and “RESUME”
appears in the front panel display. As long as
you do not remove the disc, Resume Play will
work even if the system enters standby mode by
pressing "/1.
1
• [TITLE VIEWER] (DVD VIDEO only)
• [CHAPTER VIEWER] (DVD VIDEO
only)
• [TRACK VIEWER] (VIDEO CD/
Super VCD only)
3
Press
“RESUME” appears in the front panel
display.
If “RESUME” does not appear, Resume
Play is not available.
2
.
While playing a disc, press x to stop
playback.
Press H.
The system starts playback from the point
where you stopped the disc in Step 1.
The first scene of each title, chapter, or
track appears as follows.
Note
4
1
2
3
4
5
6
7
8
9
Press C/X/x/c to select a title, chapter,
or track, and press
.
The system starts playback from the
selected scene.
To return to normal play during
setting
Press O RETURN.
Note
• Depending on the disc, you may not be able to select
some items.
38GB
• Depending on where you stop the disc, the system
may not resume playback from exactly the same
point.
• The point where you stopped playing may be cleared
when:
– you eject the disc.
– the system enters standby mode (DATA CD/
DATA DVD only).
– you change or reset the settings on the Setup
Display.
– you change the parental control level.
– you change the function by pressing FUNCTION.
– you disconnect the AC power cord (mains lead).
• For DVD-Rs/DVD-RWs in VR mode, VIDEO CDs,
CDs, DATA CDs, and DATA DVDs, the system
remembers the resume playback point for the current
disc.
• Resume Play does not work during Program Play and
Shuffle Play.
• This function may not work properly with some
discs.
Tip
• To play from the beginning of the disc, press x twice,
then press H.
To enjoy a disc that is played
before by resume playback
(Multi-disc Resume)
(DVD VIDEO, VIDEO CD only)
(Program Play)
You can play the contents of a disc in the order
you want by arranging the order of the tracks on
the disc to create your own program. You can
program up to 99 tracks.
1
DISPLAY.
The Control Menu display appears.
2
Press X/x to select
[PROGRAM], then press
.
The options for [PROGRAM] appear.
Tip
T
• To play from the beginning of the disc, press x twice,
then press H.
6 (14)
2:50
PLAY
CD
OFF
OFF
SET
ON
Note
• If [MULTI-DISC RESUME] in [CUSTOM SETUP]
is set to [OFF] (page 80), the resume point is cleared
when you change the function by pressing
FUNCTION.
Press
3
Press X/x to select [SET
press
.
t], then
Various Functions for Playing Discs
This system stores the point where you stopped
the disc for up to 40 discs and resumes playback
the next time you insert the same disc. If you
store a resume playback point for the 41st disc,
the resume playback point for the first disc is
deleted.
To activate this function, set [MULTI-DISC
RESUME] in [CUSTOM SETUP] to [ON]. For
details, see “[MULTI-DISC RESUME] (DVD
VIDEO/VIDEO CD only)” (page 80).
Creating Your Own
Program
[TRACK] is displayed when you play a
VIDEO CD or CD.
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK – –
3. TRACK – –
4. TRACK – –
5. TRACK – –
6. TRACK – –
7. TRACK – –
Tracks recorded
on a disc
4
0:00:00
T
––
01
02
03
04
05
06
Total time of the
programmed tracks
Press c.
The cursor moves to the track row [T] (in
this case, [01]).
continued
39GB
PROGRAM
ALL CLEAR
1. TRACK – –
2. TRACK – –
3. TRACK – –
4. TRACK – –
5. TRACK – –
6. TRACK – –
7. TRACK – –
5
––
01
02
03
04
05
06
To cancel a program, select [--] under [T],
then press
.
To cancel all of the tracks in the
programmed order
1
Follow steps 1 to 3 of “Creating Your Own
Program.”
2
3
Press X and select [ALL CLEAR].
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
0:15:30
T
02
––
––
––
––
––
––
––
01
02
03
04
05
06
Total time of the programmed tracks
To program other tracks, repeat steps 4
to 5.
The programmed tracks are displayed in the
selected order.
Press H to start Program Play.
Program Play starts.
When the program ends, you can restart the
same program again by pressing H.
To return to normal play
In Step 3, press CLEAR or select [OFF]. To play
the same program again, select [ON] in Step 3
and press .
To turn off the Control Menu
display
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
To change or cancel a program
40GB
Follow Step 5 for new programming.
For example, select track [02].
Press X/x to select [02] under [T], then
press .
PROGRAM
7
3
Select the track you want to program.
Selected track
6
If you want to delete the track from the
program, press CLEAR.
0:00:00
T
1
Follow steps 1 to 3 of “Creating Your Own
Program.”
2
Select the program number of the track you
want to change or cancel using X/x.
Press
.
Playing in Random Order
To turn off the Control Menu
display
(Shuffle Play)
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
You can have the system “shuffle” tracks.
Subsequent “shuffling” may produce a different
playing order.
• You cannot use this function with VIDEO CDs and
Super VCDs with PBC playback.
Note
Note
• Same song may be played repeatedly during MP3
playback.
1
Press
DISPLAY during playback.
Press X/x to select
then press
.
[SHUFFLE],
The options for [SHUFFLE] appear.
T
6 (14)
2:50
PLAY
CD
OFF
OFF
TRACK
3
Press X/x to select the item to be
shuffled.
Various Functions for Playing Discs
The Control Menu display appears.
2
x When playing a VIDEO CD or CD
• [TRACK]: shuffles tracks on the disc.
x When Program Play is activated
• [ON]: shuffles tracks selected in Program
Play.
x When playing a DATA CD (except for
DivX) or DATA DVD (except for DivX)
• [ON (MP3)]: shuffles MP3 audio tracks in
the album on the current disc. When no
album is selected, the first album will play
in random order.
Note
• A track already played is also selected in
random order.
4
Press
.
Shuffle Play starts.
To return to normal play
In Step 3, press CLEAR or select [OFF].
41GB
• [TRACK] (MP3 audio tracks only):
repeats the current track.
• [FILE] (DivX video files only): repeats
the current file.
Playing Repeatedly
(Repeat Play)
4
Press
.
The item is selected.
You can play all the titles, tracks or albums on a
disc or a single title, chapter, track, or album
repeatedly.
You can use a combination of Shuffle or
Program Play modes.
To return to normal play
1
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
Press
DISPLAY during playback.
The Control Menu display appears.
2
Press X/x to select
then press
.
[REPEAT],
The options for [REPEAT] appear.
T
6 (14)
2:50
PLAY
CD
OFF
OFF
DISC
TRACK
3
Press X/x to select the item to be
repeated.
The default setting is underlined.
x When playing a DVD VIDEO or DVDVR
• [OFF]: does not play repeatedly.
• [DISC]: repeats all of the titles on the disc.
• [TITLE]: repeats the current title on a
disc.
• [CHAPTER]: repeats the current chapter.
x When playing a VIDEO CD or CD
• [OFF]: does not play repeatedly.
• [DISC]: repeats all of the tracks on the
disc.
• [TRACK]: repeats the current track.
x When playing a DATA CD or DATA
DVD
• [OFF]: does not play repeatedly.
• [DISC]: repeats all of the albums on the
disc.
• [ALBUM]: repeats the current album.
42GB
In Step 3, press CLEAR or select [OFF].
To turn off the Control Menu
display
Note
• You cannot use this function with VIDEO CDs and
Super VCDs with PBC playback.
• When playing a DATA CD/DATA DVD which
contains MP3 audio track and JPEG image files, and
their playing time is not the same, the audio sound
will not match the image.
• When [MODE (MP3, JPEG)] is set to [IMAGE
(JPEG)] (page 53), you cannot select [TRACK].
Using the DVD’s Menu
1
Press DVD TOP MENU or DVD MENU.
The disc’s menu appears on the TV screen.
The contents of the menu vary from disc to
disc.
2
3
When playing a DVD VIDEO or DATA CD/
DATA DVD (DivX video files) recorded in
multiple audio formats (PCM, Dolby Digital,
MPEG audio, or DTS), you can change the
audio format. If the DVD VIDEO is recorded
with multilingual tracks, you can also change the
language.
With VIDEO CDs, CDs, DATA CDs, or DATA
DVDs, you can select the sound from the right or
left channel and listen to the sound of the
selected channel through both the right and left
speakers.
1
The following display appears.
Press C/X/x/c or the number buttons to
select the item you want to play or
change.
Press
Press AUDIO during playback.
1:ENGLISH DOLBY DIGITAL 3/2.1
.
2
Press AUDIO repeatedly to select the
desired audio signal.
Various Functions for Playing Discs
A DVD is divided into a lot of sections, which
make up a picture or music feature. These
sections are called “titles.” When you play a
DVD which contains several titles, you can
select the title you want using DVD TOP
MENU.
When you play DVDs that allow you to select
items such as the language for the subtitles and
the language for the sound, select these items
using DVD MENU.
Changing the Sound
x When playing a DVD VIDEO
Depending on the DVD VIDEO, the choice
of language varies.
When four digits are displayed, they
indicate a language code. Refer to
“Language Code List” (page 95) to see
which language the code represents. When
the same language is displayed two or more
times, the DVD VIDEO is recorded in
multiple audio formats.
x When playing a DVD-VR
The types of sound tracks recorded on a disc
are displayed. The default setting is
underlined.
Example:
• [1: MAIN] (main sound)
• [1: SUB] (sub sound)
• [1: MAIN+SUB] (main and sub sound)
• [2: MAIN]
• [2: SUB]
continued
43GB
• [2: MAIN+SUB]
x When playing a DVD
Note
Example:
• [2: MAIN], [2: SUB], and [2: MAIN+SUB] do
not appear when one audio stream is recorded on
the disc.
x When playing a VIDEO CD, CD, DATA
CD (MP3 audio), or DATA DVD (MP3
audio)
The default setting is underlined.
• [STEREO]: the standard stereo sound
• [1/L]: the sound of the left channel
(monaural)
• [2/R]: the sound of the right channel
(monaural)
x When playing a DATA CD (DivX
video) or DATA DVD (DivX video)
The choice of DATA CD or DATA DVD
audio signal formats differ, depending on
the DivX video file contained on the disc.
The format is shown in the display.
Dolby Digital 5.1 ch
1:ENGLISH DOLBY DIGITAL 3 / 2 .1
Note
• While playing a Super VCD on which the audio track
2 is not recorded, no sound will come out when you
select [2:STEREO], [2:1/L], or [2:2/R].
L
Front (L/R) +
Center
C
R
LFE
LS
RS
Currently playing
program format
Example:
Dolby Digital 3 ch
Surround
(Monaural)
Front (L/R)
x When playing a Super VCD
The default setting is underlined.
• [1:STEREO]: the stereo sound of the
audio track 1
• [1:1/L]: the sound of the left channel of
the audio track 1 (monaural)
• [1:2/R]: the sound of the right channel of
the audio track 1 (monaural)
• [2:STEREO]: the stereo sound of the
audio track 2
• [2:1/L]: the sound of the left channel of
the audio track 2 (monaural)
• [2:2/R]: the sound of the right channel of
the audio track 2 (monaural)
LFE (Low
Frequency Effect)
Surround (L/R)
2:SPANISH DOLBY DIGITAL 2 / 1
L
R
S
Currently playing
program format
x When playing a DATA CD (DivX video) or
DATA DVD (DivX video)
Example:
MP3 audio
1: MP3 128k
Bit rate
About audio signals
Checking the audio signal
format
(DVD, DivX video only)
If you press AUDIO repeatedly during
playback, the format of the current audio signal
(PCM, Dolby Digital, DTS, etc.) appears as
shown below.
44GB
Audio signals recorded in a disc contain the
sound elements (channels) shown below. Each
channel is output from a separate speaker.
• Front (L)
• Front (R)
• Center
• Surround (L)
• Surround (R)
• Surround (Monaural): This signal can be either
the Dolby Surround Sound processed signals
or the Dolby Digital sound’s monaural
Surround audio signals.
• LFE (Low Frequency Effect) signal
Selecting [ORIGINAL] or
[PLAY LIST] on a DVD-R/
DVD-RW
1
Press
DISPLAY when the system is
in stop mode.
The Control Menu display appears.
2
Press X/x to select
PLAY LIST], then press
[ORIGINAL/
.
The options for [ORIGINAL/PLAY LIST]
appear.
1 (44)
3 ( 28)
T
1:30:50
DVD-VR
PLAY LIST
PLAY LIST
ORIGINAL
3
Various Functions for Playing Discs
Some DVD-Rs/DVD-RWs in VR (Video
Recording) mode have two types of titles for
playback: originally recorded titles
([ORIGINAL]) and titles that can be created on
recordable DVD players for editing ([PLAY
LIST]). You can select the type of title to be
played.
Press X/x to select a setting.
The default setting is underlined.
• [PLAY LIST]: plays the titles created
from [ORIGINAL] for editing.
• [ORIGINAL]: plays the titles originally
recorded.
4
Press
.
45GB
Viewing Information About
the Disc
When playing a DATA CD (MP3
audio) or DATA DVD (MP3 audio)
1 Playing time and current track number
2 Track (file) name
Tip
• When playing VIDEO CDs with PBC functions, the
playing time is displayed.
Viewing the playing time and
remaining time in the front
panel display
You can check disc information, such as the
remaining time, total number of titles in a DVD,
tracks in a VIDEO CD, CD, MP3, or file name
of a DivX video using the front panel display
(page 98).
Press DISPLAY.
Each time you press DISPLAY while playing
the disc, the display changes 1 t 2 t ...
t 1 t ...
Some displayed items may disappear after a few
seconds.
When playing a DVD VIDEO or
DVD-R/DVD-RW
1 Playing time and number of the current title
2 Remaining time of the current title
3 Playing time and number of the current
chapter
4 Remaining time of the current chapter
5 Disc name
6 Title and chapter
When playing a DATA CD (DivX
video) or DATA DVD (DivX video)
1 Playing time of the current file
2 Current file name
3 Current album and file number
When playing a VIDEO CD
(without PBC functions) or CD
1 Playing time of the current track
2 Remaining time of the current track
3 Playing time of the disc
4 Remaining time of the disc
5 Disc name
6 Track and index*
* VIDEO CD only.
46GB
Note
• The system can only display the first level of the
DVD/CD text, such as the disc name or title.
• If an MP3 file name cannot be displayed, “*” will
appear in the front panel display instead.
• The disc name or track name may not be displayed
depending on the text.
• Playing time of MP3 audio tracks and DivX video
files may not be displayed correctly.
Checking the playing time and
remaining time
You can check the playing time and remaining
time of the current title, chapter, or track, and the
total playing time or remaining time of the disc.
You can also check the DVD text and MP3
folder name/file name recorded in the disc.
1
Press DISPLAY during playback.
The following display appears.
T 1:01:57
Time information
2
Press DISPLAY repeatedly to change
the time information.
The display and the kinds of time that you
can check depend on the disc you are
playing.
x When playing a DVD VIDEO or DVDRW
• T **:**:**
Playing time of the current title
• T–**:**:**
Remaining time of the current title
• C **:**:**
Playing time of the current chapter
• C–**:**:**
Remaining time of the current chapter
x When playing a VIDEO CD (with PBC
functions)
• **:**
Playing time of the current scene
CD/DATA DVD, you can display the name of
the album/track/file, and the audio bit rate (the
amount of data per second of the current audio)
on your TV screen.
x When playing a VIDEO CD (without
PBC functions) or CD
Bit rate*
x When playing a DATA CD (MP3
audio) or DATA DVD (MP3 audio)
• T **:**
Playing time of the current track
x When playing a DATA CD (DivX
video) or DATA DVD (DivX video)
• **:**:**
Playing time of the current file
Note
• Characters/marks may not be displayed for some
languages.
• Depending on the type of disc being played, the
system can only display a limited number of
characters. Also, depending on the disc, not all text
characters will be displayed.
T 17:30
JAZZ
RIVER SIDE
Album name
Track/file name
* Appears when:
– playing an MP3 audio track on DATA CDs/DATA
DVDs.
– playing a DivX video file that contains MP3 audio
signals on DATA CDs/DATA DVDs.
Checking the date
information
(JPEG only)
You can check the date information during
playback when the Exif* tag is recorded in the
JPEG image data.
1(8)
1(20)
2007/ 01/ 31
Checking the play information
of the disc
DATA CD JPEG
Date information
To check DVD/CD text
Press DISPLAY repeatedly in Step 2 to display
text recorded in the DVD/CD.
The DVD/CD text appears only when text is
recorded in the disc. You cannot change the text.
If the disc does not contain text, “NO TEXT”
appears.
128k
Various Functions for Playing Discs
• T **:**
Playing time of the current track
• T–**:**
Remaining time of the current track
• D **:**
Playing time of the current disc
• D–**:**
Remaining time of the current disc
Press
DISPLAY twice during playback.
The Control Menu display appears.
* “Exchangeable Image File Format” is a digital
camera image format defined by the Japan
Electronics and Information Technology Industries
Association (JEITA).
BRAHMS SYMPHONY
Tip
To check DATA CD/DATA DVD
(MP3 audio/DivX video) text
By pressing DISPLAY while playing MP3
audio tracks or DivX video files on a DATA
• Date information is [YYYY/MM/DD].
YYYY: Year
MM: Month
DD: Day
• Date information varies depending on the area.
47GB
Changing the Angles
If various angles (multi-angles) for a scene are
recorded on a DVD VIDEO, you can change the
viewing angle.
Press ANGLE during playback.
Each time you press ANGLE, the angle changes.
Note
• Depending on the DVD VIDEO, you may not be able
to change the angle even if multi-angles are recorded
on the DVD VIDEO.
Displaying the Subtitles
If subtitles are recorded on a disc, you can turn
the subtitles on or off while playing. If
multilingual subtitles are recorded on the disc,
you can change the subtitle language while
playing, or turn the subtitles on or off whenever
you want.
Press SUBTITLE during playback.
Each time you press SUBTITLE, the subtitle
language changes.
Note
• Depending on the DVD VIDEO, you may not be able
to change the subtitles even if multilingual subtitles
are recorded on it. You also may not be able to turn
them off.
• You can change the subtitles if the DivX video file
has an “.AVI” or “.DIVX” extension and contains
subtitle information within the same file.
48GB
Adjusting the Delay
Between the Picture and
Sound
About MP3 Audio Tracks
and JPEG Image Files
(A/V SYNC)
What is MP3/JPEG?
When the sound does not match the pictures on
the TV screen, you can adjust the delay between
the picture and sound.
Press
DISPLAY.
The Control Menu display appears.
2
Press X/x to select
then press
.
[A/V SYNC],
The options for [A/V SYNC] appear.
1(12)
1(28)
T
0:00:02
DVD VIDEO
OFF
OFF
ON
3
Press X/x to select a setting.
The default setting is underlined.
• [OFF]: does not adjust.
• [ON]: adjusts the difference between
picture and sound.
4
Press
.
Note
• Depending on the input stream, this function may not
be effective.
Discs that the system can
play
You can play back DATA CDs (CD-ROMs/CDRs/CD-RWs) or DATA DVDs (DVD-Rs/DVDRWs/DVD+Rs/DVD+RWs/DVD-ROMs)
recorded in MP3 (MPEG1 Audio Layer 3) or
JPEG format. However, the DATA CDs must be
recorded according to ISO 9660 Level 1, Level
2 or Joliet format and DATA DVDs of Universal
Disk Format (UDF) for the system to recognize
the tracks (or files). You can also play discs
recorded in Multi Session.
See the operating instructions supplied with the
CD-R/CD-RW or DVD-R/DVD-RW drives and
the recording software (not supplied) for details
on the recording format.
Various Functions for Playing Discs
1
MP3 is audio compression technology that
satisfies the ISO/MPEG regulations. JPEG is
image compression technology.
About the Multi-Session disc
If MP3 audio tracks or JPEG image files are
recorded in the first session, the system will also
play MP3 audio tracks or JPEG image files in
other sessions. If audio tracks and images in
audio CD format or video CD format are
recorded in the first session, only the first
session will be played back.
Note
• The system may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
continued
49GB
MP3 audio track or JPEG
image file that the system can
play
You can play the MP3 audio tracks or JPEG
image files:
• which have the extension “.MP3” (MP3 audio
track) or “.JPG”/“.JPEG” (JPEG image file)
• which conform to the DCF* image file format
Playback order of MP3 audio
tracks or JPEG image files
The playback order of MP3 audio tracks or
JPEG image files recorded on a DATA CD or
DATA DVD is as follows:
x Structure of disc contents
Tree 1
Tree 2
Tree 3
Tree 4
Tree 5
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by Japan
Electronics and Information Technology Industries
Association (JEITA).
Note
• The system will play any data with the
extension “.MP3,” “.JPG,” or “.JPEG” even if
they are not in MP3 or JPEG format. Playing
this data may generate a loud noise which
could damage your speaker system.
• The system does not conform to audio in
MP3PRO format.
Album
Track (MP3 audio) or
File (JPEG image)
When you insert a DATA CD or DATA DVD
and press H, the numbered tracks (or files) are
played sequentially, from 1 through 7. Any
sub-albums/tracks (or files) contained within a
currently selected album take priority over the
next album in the same tree. (Example: C
contains D so 4 is played before 5.)
When you press DVD MENU and the list of
album names appears (page 51), the album
names are arranged in the following order:
A t B t C t D t F t G. Albums
that do not contain tracks (or files) (such as
album E) do not appear in the list.
50GB
Tip
• If you add numbers (01, 02, 03, etc.) to the front of the
track (or file) names when you store the tracks (or
files) in a disc, the tracks (or files) will be played in
that order.
• A disc with many trees takes longer to start playback.
Note
Selecting an MP3 audio track
or album
1
Load a DATA CD or DATA DVD.
The albums recorded on the DATA CD or
DATA DVD appear. When an album is
being played, its title is shaded.
3( 30)
ROCK BEST HIT
KARAOKE
MY FAVOURITE SONG
R&B
JAZZ
CLASSIC
SALSA OF CUBA
BOSSA NOVA
2
Press X/x to select an album.
Various Functions for Playing Discs
• Playback order may differ from the illustration
depending on the software you use to create the
DATA CD or DATA DVD, or if there are more than
200 albums and 300 files in each album.
• The system can recognize up to 200 albums, and will
not play any albums beyond the 200th.
• The system may take longer time to playback, when
progressing to the following album or jump to other
album.
• Some type of JPEG files cannot be played.
Playing DATA CDs or
DATA DVDs with MP3
Audio Tracks and JPEG
Image Files
x When selecting an album
Press H to start playing the selected
album.
x When selecting a track
Press
.
The list of tracks contained in the album
appears.
MY FAVOURITE SONG
1(256)
WALTZ FOR DEBBY
MY ROMANCE
MILES TONES
MY FUNNY VALENTINE
AUTUMN LEAVES
ALL BLUES
S O M E D A Y M Y P R I N C E W ...
Press X/x to select a track and press
.
The selected track starts playing. You can
turn the track list off by pressing DVD
MENU. Pressing DVD MENU again will
display the album list.
continued
51GB
To stop playback
Press x.
To play the next or previous MP3
audio track
Press ./>. Note that you can select the
next album by continuing to press > after the
last track on the current album, but that you
cannot return to the previous album by pressing
.. To return to the previous album, select the
album from the album list.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Press C/X/x/c to select the image you want
to view and press
.
To return to the previous display
Press O RETURN.
To turn off the display
Press DVD MENU.
Selecting a JPEG image file or
album
1
Load a DATA CD or DATA DVD.
The albums recorded on the DATA CD or
DATA DVD appear. When an album is
being played, its title is shaded.
3( 30)
ROCK BEST HIT
KARAOKE
MY FAVOURITE SONG
R&B
JAZZ
CLASSIC
SALSA OF CUBA
BOSSA NOVA
2
Press X/x to select an album.
x When selecting an album
Press H to start playing the selected
album.
To play the next or previous JPEG
image file
Press C/c when the Control Menu display is not
displayed. Note that you can select the next
album by continuing to press c after the last
image on the current album, but that you cannot
return to the previous album by pressing C. To
return to the previous album, select the album
from the album list.
To rotate a JPEG image
When a JPEG image file is displayed on the TV
screen, you can rotate the image by 90 degrees.
Press X/x while viewing an image. Each time
you press X, the image rotates counterclockwise
by 90 degrees.
Example of when you press X once:
Rotating direction
x When selecting an image
Press PICTURE NAVI.
Images of files in the album appear in 16
subscreens.
Press CLEAR to return to normal view.
52GB
To stop playback
Press x.
Tip
• A scroll box is displayed at the right side of the TV
screen. To display the additional image files, select
the bottom image and press x. To return to the
previous image, select the top image and press X.
Playing Audio Tracks and
Images as a Slide Show
with Sound
You can play a slide show with sound by first
placing both MP3 and JPEG files in the same
album on a DATA CD or DATA DVD. When
you play back the DATA CD or DATA DVD,
select [AUTO] mode as explained below.
Load a DATA CD or DATA DVD.
Press
DISPLAY when the system is
in stop mode.
The Control Menu display appears.
3
Press X/x to select
(MP3, JPEG)], then press
[MODE
.
The options for [MODE (MP3, JPEG)]
appear.
12(27)
18(34)
T
1:32:55
DATA CD MP3
AUTO
AUTO
AUDIO (MP3)
IMAGE (JPEG)
4
Various Functions for Playing Discs
1
2
Press X/x to select a setting.
The default setting is underlined.
• [AUTO]: plays both the JPEG image files
and MP3 audio tracks in the same album
as a slide show.
• [AUDIO (MP3)]: plays only MP3 audio
tracks continuously.
• [IMAGE (JPEG)]: plays only JPEG
image files as a slide show.
5
6
Press
.
Press DVD MENU.
The list of albums recorded on the DATA
CD or DATA DVD appears.
7
Press X/x to select the album you want
and press H.
continued
53GB
The system starts playing the selected
album.
You can turn the album list on and off by
pressing DVD MENU repeatedly.
• [FAST]: sets the duration shorter than
[NORMAL].
• [SLOW1]: sets the duration longer than
[NORMAL].
• [SLOW2]: sets the duration longer than
[SLOW1].
Tip
• When you select [AUTO], the system can recognize
up to 300 MP3 tracks and 300 JPEG files in a single
album. When you select [AUDIO (MP3)] or [IMAGE
(JPEG)], the system can recognize up to 600 MP3 or
600 JPEG files in a single album. A maximum of 200
albums can be recognized regardless of the selected
mode.
Note
• If you set [MODE (MP3, JPEG)] to [IMAGE
(JPEG)] on a disc that contains MP3 tracks only or
[AUDIO (MP3)] on a disc that contains JPEG files
only, you may not be able to change the [MODE
(MP3, JPEG)] setting.
• PICTURE NAVI does not work when [AUDIO
(MP3)] is selected.
• If you play large MP3 track data and JPEG image
data at the same time, the sound may skip. It is
recommended that you set the MP3 bit rate to 128
kbps or lower when creating the file. If the sound still
skips, then reduce the size of the JPEG file.
4
Note
Selecting an effect for image
files in the slide show
(JPEG only)
When you play a JPEG image file, you can
select the effect to be used when viewing the
slide show.
1
The Control Menu display appears.
3
3
DATA CD JPEG
Press X/x to select a setting.
The default setting is underlined.
• [NORMAL]: sets the duration to about 6
to 9 seconds.
4
54GB
DATA CD JPEG
Press X/x to select a setting.
The default setting is underlined.
• [MODE1]: The image sweeps in from top
to bottom.
• [MODE2]: The image stretches out from
left to right of the TV screen.
• [MODE3]: The image stretches out from
the center of the TV screen.
• [MODE4]: The images randomly cycle
through the effects.
• [MODE5]: The next image slides over the
previous image.
• [OFF]: turns off this function.
The options for [INTERVAL] appear.
3 ( 12)
4)
1(
2007/10/29
NORMAL
NORMAL
FAST
SLOW1
SLOW2
[EFFECT],
MODE1
MODE1
MODE2
MODE3
MODE4
MODE5
OFF
DISPLAY twice.
.
Press X/x to select
then press
.
3 ( 12)
4)
1(
2007/10/23
When you play JPEG image files using slide
show, you can specify the duration for slides to
appear on the TV screen.
Press X/x to select
[INTERVAL], then press
DISPLAY twice.
The options for [EFFECT] appear.
(JPEG only)
2
Press
The Control Menu display appears.
2
Press
.
• Some JPEG files may take longer to display than
others, which may make the duration seems longer
than the option you selected. Especially progressive
JPEG files or JPEG files of 3,000,000 pixels or more.
Specifying the slide show
duration
1
Press
Press
.
Enjoying DivX® Videos
files with the extension “.AVI” or “.DIVX” if
they do not contain a DivX video.
Tip
About DivX Video Files
DivX® is a video file compression technology,
developed by DivX, Inc. This product is an
official DivX® Certified product.
You can play DATA CDs and DATA DVDs that
contain DivX® video files.
Playback of DATA CDs (CD-ROMs/CD-Rs/
CD-RWs) and DATA DVDs (DVD-ROMs/
DVD-Rs/DVD-RWs/DVD+Rs/DVD+RWs) on
this system is subject to certain conditions:
– With DATA CDs/DATA DVDs that contain
DivX video files in addition to MP3 audio
tracks or JPEG image files, the system plays
only the DivX video files.
However, this system only plays DATA CDs
whose logical format is ISO 9660 Level 1/Level
2 or Joliet, and DATA DVDs of Universal Disk
Format (UDF).
Refer to the operating instructions supplied with
the disc drives and the recording software (not
supplied) for details on the recording format.
Note
• The system may not play a DivX video file when the
file has been combined from two or more DivX video
files.
• The system cannot play a DivX video file of size
more than 720 (width) × 576 (height) or 2GB.
• Depending on the DivX video file, sound may skip or
not match the pictures on the TV screen.
• The system cannot play some DivX video files that
are longer than 3 hours.
• Depending on the DivX video file, the picture may
pause or be unclear. In which case, it is recommended
that you create the file at a lower bit rate. If the sound
is still noisy, MP3 is the recommended audio format.
Note, however, this system does not conform to
WMA (Windows Media Audio) format.
• Because of the compression technology used for
DivX video files, it may take some time after you
press H for the picture to appear.
Selecting an album
1
A list of albums on the disc appears. Only
albums that contain DivX video files are
listed.
About playback order of data on
DATA CDs or DATA DVDs
See “Playback order of MP3 audio tracks or
JPEG image files” (page 50). Note that the
playback order may not be applicable,
depending on the software used for creating the
DivX video file, or if there are more than 200
albums and 600 DivX video files in each album.
Note
• The system may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
DivX video files that the system
can play
The system can play data that is recorded in
DivX format, and which has the extension
“.AVI,” or “.DIVX.” The system will not play
Press DVD MENU.
Various Functions for Playing Discs
DATA CDs and DATA DVDs that
the system can play
• For details about playable MP3 audio tracks or JPEG
image files on DATA CDs or DATA DVDs, see
“Discs that the system can play” (page 49).
3( 3)
SUMMER 2003
NEW YEAR'S DAY
MY FAVOURITES
2
3
Press X/x to select the album you want
to play.
Press H.
The system starts playing the selected
album.
To select DivX video files, see “Selecting a
DivX video file” (page 56).
continued
55GB
To go to the next or previous
page
Tip
• If the number of viewing times is preset, you can play
the DivX video files as many times as the preset
number. The following occurrences are counted:
– when the system is turned off.
– when another file is played.
– when the disc tray is opened.
Press C/c.
To turn off the display
Press DVD MENU repeatedly.
To stop playback
Press x.
Selecting a DivX video file
1
After Step 2 of “Selecting an album,”
press
.
The list of files in the album appears.
MY FAVOURITES
1(2 )
HAWAII 2004
VENUS
2
Press X/x to select a file and press
.
The selected file starts playing.
To go to the next or previous
page
Press C/c.
To return to the previous display
Press O RETURN.
To stop playback
Press x.
To play the next or previous DivX
video file without turning on the
above file list
You can select the next or previous DivX video
file in the same album by pressing ./>.
You can also select the first file of the next
album by pressing > during playback of the
last file of the current album. Note that you
cannot return to the previous album by pressing
.. To return to the previous album, select it
from the album list.
56GB
Playing VIDEO CDs with
PBC Functions (Ver.2.0)
(PBC Playback)
With PBC (Playback Control) functions, you
can enjoy simple interactive operations, search
functions, and other such operations.
PBC playback allows you to play VIDEO CDs
interactively by following the menu on the TV
screen.
Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
2
3
4
Select the item number you want by the
number buttons.
Press
.
Follow the instructions in the menu for
interactive operations.
Refer to the operating instructions supplied
with the disc, as the operating procedure
may differ depending on the VIDEO CD.
To go back to the menu
Various Functions for Playing Discs
1
Press O RETURN.
Note
• Depending on the VIDEO CD, [Press ENTER] in
Step 3 may appear as [Press SELECT] in the
operating instructions supplied with the disc. In this
case, press H.
Tip
• To play without using PBC, press ./> or the
number buttons while the system is in stop mode to
select a track, then press H or
. The system starts
continuous play. You cannot play still pictures such
as a menu. To return to PBC playback, press x twice,
then press H.
57GB
To change the preset number
Tuner Functions
Presetting Radio Stations
You can preset 20 FM stations, and 10 AM
stations. Before tuning, make sure to turn down
the volume to minimum.
1
2
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
Press and hold TUNING + or – until the
auto scanning starts.
Scanning stops when the system tunes in a
station. “TUNED” and “ST” (for stereo
program) appear in the front panel display.
3
4
5
Press SYSTEM MENU.
Press X/x repeatedly until “MEMORY”
appears in the front panel display.
Press
or c.
A preset number appears in the front panel
display.
6
Press X/x to select the preset number
you want.
Tip
• You can select the preset number directly by
pressing the number buttons.
7
Press
.
The station is stored.
8
9
Repeat Steps 1 to 7 to store other
stations.
Press SYSTEM MENU.
The system menu turns off.
58GB
Restart from Step 1.
To change the AM tuning interval
(except for Russian and Middle
Eastern models)
The AM tuning interval can be set to either
10 kHz or 9 kHz.
To change the AM tuning interval, first tune in
any AM station, then turn off the system by
pressing "/1 on the unit. While holding down
> on the unit, press "/1 on the unit to turn on
the power. If you change the interval, AM preset
stations will be erased.
To reset the interval, repeat the same procedure.
Listening to the Radio
Preset radio stations in the system’s memory
first (see “Presetting Radio Stations” (page 58)).
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
If an FM program is noisy
If an FM program is noisy, you can select
monaural reception. There will be no stereo
effect, but reception will improve.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “FM MODE”
appears in the front panel display.
The last received station is tuned in.
2
Press PRESET + or – repeatedly to
select the preset station.
Each time you press the button, the system
tunes in one preset station.
3
4
To turn off the radio
5
Use manual or automatic tuning in Step 2.
For manual tuning, press TUNING + or –
repeatedly.
For automatic tuning, press and hold TUNING +
or –. The automatic tuning stops automatically
when the system receives the radio station. To
stop the automatic tuning manually, press
TUNING + or –.
To listen to radio stations when
you know the frequencies
6
Press SYSTEM MENU.
Naming preset stations
You can enter a name for preset stations. These
names (for example, “XYZ”) appear in the front
panel display when a station is selected.
Note that no more than one name can be entered
for each preset station.
1
Press D.TUNING.
Press the number buttons to select the
frequencies.
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
The last received station is tuned in.
2
Use direct tuning in Step 2.
Press
.
The system menu turns off.
To listen to non-preset radio
stations
3
Press
The setting is made.
Press "/1.
1
2
Press X/x to select “MONO.”
Tuner Functions
Adjust the volume by pressing
VOLUME +/–.
or c.
The default setting is underlined.
• “STEREO”: stereo reception.
• “MONO”: monaural reception.
Tip
• You can select the preset station number directly
by pressing the number buttons.
3
Press
3
4
.
Press PRESET + or – repeatedly to
select the preset station you want to
create an index name for.
Press SYSTEM MENU.
Press X/x repeatedly until “NAME IN”
appears in the front panel display.
Tip
• To improve reception, reorient the supplied antennas
(aerials).
5
6
Press
or c.
Create a name by using the cursor
buttons.
continued
59GB
Press X/x to select a character, then press c
to move the cursor to the next position.
Letters, numbers, and other symbols can be
input for a radio station.
If you make a mistake
Press C/c repeatedly until the character to
be changed flashes, then press X/x to select
the desired character.
To erase the character, press C/c
repeatedly until the character to be erased
flashes, then press CLEAR.
7
Press
.
“COMPLETE” appears in the front panel
display, and the station name is stored.
8
Press SYSTEM MENU.
The system menu turns off.
Tip
• You can check the frequency by pressing DISPLAY
repeatedly (page 60).
Viewing the station name or
frequency in the front panel
display
When the system is set to “TUNER FM” or
“TUNER AM,” you can check the frequency
using the front panel display.
Press DISPLAY.
Each time you press DISPLAY, the display
changes as shown.
1 Station name*
2 Frequency**
* This is displayed if you have entered a name for a
preset station.
** Returns to the original display when several seconds
has elapsed.
60GB
Other Operations
Controlling the TV with the
Supplied Remote
You can control your TV (Sony only) with the
supplied remote.
Controlling TVs with the
remote
You can control the TV by using following
buttons.
By pressing
You can
Turn the TV on or off.
TV INPUT*
Switch the TV’s input source
between the TV and other input
sources.
TV VOL +/–*
Adjust the TV volume.
TV CH +/–*
Select the TV channel.
Number
buttons*,
ENTER*
Select the TV channel.
DVD MENU*
C/X/x/c*,
RETURN*
THEATRE SYNC allows you to turn on your
Sony TV and this system, changes the system
mode to “DVD,” and then switches the TV’s
input source you set with one button push.
Preparing for the THEATRE
SYNC function
Register the TV’s input source connected to this
system.
Press and hold TV INPUT* while entering
the code for the TV’s input source
connected to this unit (see the table) using
the number buttons.
* Functions as both TV INPUT and DISPLAY button.
The TV’s input source is selected.
Set your TV’s input to the input you used to
connect the unit. For details, see the operating
instructions of your TV.
By pressing Number
TV’s input source
TV INPUT
0
No input source
(Default)
Select the item on the menu.
1
VIDEO1
Return to the previous channel or
layer on the menu of the TV.
2
VIDEO2
3
VIDEO3
4
VIDEO4
5
VIDEO5
6
VIDEO6
7
VIDEO7
8
VIDEO8
Display the menu of the TV.
*
* Use these buttons while pressing the TV button.
- is for selecting a channel number greater than
10. (For example, for channel 25, press -, then
2 and 5.)
Note
• Depending on the TV, you may not be able to control
your TV or to use some of the buttons above.
9*
COMPONENT 1
CLEAR*
COMPONENT 2
SYSTEM
MENU*
COMPONENT 3
PICTURE
NAVI*
COMPONENT 4
Other Operations
TV [/1*
Using the THEATRE SYNC
Function
* Except for North American models.
continued
61GB
Operating the THEATRE SYNC
function
Enjoying Karaoke
Point the remote to the direction of TV and this
unit, then press THEATRE SYNC once.
If this function does not work, change the
transmit time. The transmit time varies
depending on the TV.
To change the transmit time
Press and hold TV CH +* while entering the
code for transmit time (see the table) using
the number buttons.
You can enjoy karaoke (singing along with a
disc) by setting the system to karaoke mode.
You can connect two microphones (not
supplied)* to the unit.
* Only Russian models, supplied with one
microphone.
* Functions as both TV CH + and PRESET + button.
Setting the system to karaoke
mode
By pressing Number
1
The transmit time from the remote is selected.
TV CH +
Transmit time
1
0.5 (Default)
2
1
3
1.5
4
2
5
3
6
4
7
5
8
6
2
Press FUNCTION repeatedly until
“DVD” appears in the front panel
display.
Plug a microphone into the MIC 1 or
MIC 2 jack.
AUDIO IN / MIC 1 /
A.CAL MIC
MIC 2
Note
• This function is only for Sony TVs. (This function
may not work on some Sony TVs.)
• If distance between TV and this unit is too far, this
function may not work. Install the unit near the TV.
• Keep the remote pointed in the direction of the TV
and this unit while entering the code.
The system enters karaoke mode.
“
” lights up in the front panel display.
3
Start playing the music.
Microphone sound is output with DVD
function.
To cancel karaoke mode
Disconnect the microphones.
To set the system to karaoke
mode on the Control Menu
display
1
Press
DISPLAY.
The Control Menu display appears.
62GB
2
3
Note
Note
• The Control Menu display has 2 pages.
Depending on the source, press
DISPLAY
twice to select [KARAOKE MODE].
• If howling occurs:
– move the microphone away from the speakers.
– lower the microphone volume or echo level.
– lower the overall volume.
Press X/x repeatedly to select
[KARAOKE MODE], then press
.
The options for [KARAOKE MODE] appear.
Dolby Digital Karaoke format
Press X/x repeatedly to select [ON], then
press
.
(DVD only)
The system enters karaoke mode.
To cancel karaoke mode, select [OFF].
Note
Speaker output in normal Dolby
Digital format (5 channel
surround)
Front speaker
(L)
Front speaker
(R)
Center
speaker
Other Operations
• Microphone sound may drop when changing discs.
• Before connecting, press MIC VOL – to set the
microphone volume to minimum.
• You cannot change the sound field during karaoke
mode.
• In karaoke mode, the overall volume may drop.
• If you set [TEST TONE] to [ON] (page 83) during
the karaoke mode, the karaoke mode is set to off
automatically.
• Microphone sound is not output when:
– the microphone is not connected to the unit
properly.
– the microphone volume is set to minimum.
Dolby Digital format, which reproduces
surround sound using 5 channels, can also
contain the “Dolby Digital Karaoke” format
which is specialized for karaoke. In the Dolby
Digital Karaoke format discs, guide melody and
guide vocal tracks are recorded in addition to the
accompaniment. You can select them when the
system is in karaoke mode.
Tip
• The karaoke play is performed with the audio channel
you selected using AUDIO (page 43).
Adjusting the microphone
You can adjust the microphone volume and
level of the echo effect.
To adjust the microphone volume
Press MIC VOL +/– to adjust the
microphone volume.
To add the echo effect
Press ECHO.
Each time you press ECHO, the echo level
changes as follows:
ECHO OFF t ECHO 1
R
r
ECHO 3 T ECHO 2
To cancel the echo effect, select “ECHO OFF.”
Surround
speaker (L)
Surround
speaker (R)
Speaker output in Dolby Digital
Karaoke format
Accompaniment
Accompaniment
Front
(L)
Front
(R)
Center
Guide melody
Surround
(L)
Guide vocal 1
Surround
(R)
Guide vocal 2
You can select any of these. These are output
from the respective speakers.
continued
63GB
You can check the audio information by
pressing AUDIO (page 43). When playing a
Dolby Digital Karaoke disc, “ ” appears at the
current audio format.
Example:
1:ENGLISH DOLBY DIGITAL 3 / 2
2/0: Recorded only with
accompaniment.
3/0: Recorded with guide
melody.
3/1: Recorded with guide melody
and one guide vocal.
3/2: Recorded with guide melody
and two guide vocals.
Changing the key of a song
(Key Control)
You can change the key to suit your vocal range,
except when the system is in stop mode.
Press KEY CON # or 2 to suit your vocal
range in karaoke mode.
You can adjust the key higher or lower in
13 steps (26 – #6).
Note
• Depending on the discs, you may not be able to
change the key.
• The key automatically returns to the original key
when:
– you turn off the power.
– you change the function.
– the disc tray is opened.
– you stop playback.
– the title or track changes.
– you change the album.
– the play item is changed during PBC playback.
– you perform Scan Play.
– you cancel karaoke mode.
Playing karaoke with any
stereo disc (Karaoke Pon)
You can enjoy karaoke with a stereo-recorded
disc, even if it is a non-karaoke disc, by reducing
the sound of the vocals.
Press KARAOKE PON in karaoke mode.
64GB
To cancel Karaoke Pon mode
Press KARAOKE PON again.
Note
• This function may not work well in the following
cases:
– Only a few instruments are playing
– A duet is playing
– The vocals on the disc deviate from the center
– Monaural-recorded discs (the accompaniment is
also reduced)
– Multiplex
• During Karaoke Pon mode, the stereo effect is
reduced.
• Karaoke Pon mode is automatically canceled when:
– you turn off the power.
– you change the function.
– the disc tray is opened.
– AUDIO stream is changed.
– you set [VOCAL SELECT] to other than [OFF].
– you cancel karaoke mode.
Selecting the vocals (Vocal
Select)
(DVD VIDEO, VIDEO CD, CD only)
When playing a DVD with the Dolby Digital
Karaoke format in karaoke mode, you can turn
on or off the guide vocal recorded in the karaoke
track.
When playing a VIDEO CD/CD in karaoke
mode, you can listen to the vocals.
You can also change the guide vocal channel.
You can select different kinds of vocals.
1
Press
mode.
DISPLAY twice in karaoke
The Control Menu display for karaoke
mode appears.
2
Press X/x repeatedly to select
[VOCAL SELECT], then press
.
The options for [VOCAL SELECT] appear.
3
Press X/x repeatedly to select the
desired vocal channel.
The output channel changes as follows. The
default settings are underlined.
x When playing a DVD VIDEO
• [OFF]: The guide vocal is canceled.
• [1+2]: Guide vocal 1+2
• [1]: Guide vocal 1
• [2]: Guide vocal 2
x When playing a VIDEO CD/CD
2
The options for [SCORE MODE] appear.
3
• [OFF]: The guide vocal is canceled.
• [L+R]: Same sound is output from both
speakers.
• [STEREO]: The standard stereo sound
Press
.
4
5
6
.
Start playing the music.
Press SCORE before singing a song in
karaoke mode.
The previous highest score appears on the
TV screen.
7
Note
• When playing a DVD VIDEO, the function works
only with the Dolby Digital Karaoke format.
• Depending on the discs, you may not be able to
change the guide vocal channel.
• The channel returns to the default setting when:
– you turn off the power.
– you change the functions.
– the disc tray is opened.
– AUDIO stream is changed.
– you cancel karaoke mode.
– you set karaoke pon mode to on.
• When playing a DVD VIDEO recorded only with one
kind of guide vocal, select [1].
Press
After singing for more than a minute,
press SCORE again to view your score.
Your score is calculated from a scale of
0 to 99.
Your score is displayed for five seconds,
during which time the system enters pause
mode.
Other Operations
4
Press X/x repeatedly to select a
setting.
The default settings are underlined.
• [EASY]: Beginner or Intermediate level.
• [NORMAL]: Advance or professional
level.
• [DEMO]: Demonstration mode.
Consistently displays a high score for
every song.
x When playing a Super VCD
• [OFF]: The guide vocal is canceled.
• [1:L+R]: Same sound of the audio track 1
is output from both speakers.
• [1:STEREO]: The stereo sound of the
audio track 1
• [2:L+R]: Same sound of the audio track 2
is output from both speakers.
• [2:STEREO]: The stereo sound of the
audio track 2
Press X/x repeatedly to select
[SCORE MODE], then press
.
Note
• The highest score is reset when the system is turned
off.
• The score mode function may be canceled when
certain remote buttons are pressed.
• In some cases, you may not be able to use the scoring
mode.
Tip
Selecting the scoring mode
(Score Mode)
• The [SCORE MODE] setting is automatically
changed to [EASY] when the system is turned off.
When karaoke mode is turned on, you can use
the scoring mode.
Your score is calculated by comparing your
voice with the music source.
1
Press
DISPLAY.
The Control Menu display appears.
Note
• The Control Menu display has 2 pages.
Depending on the source, press
DISPLAY
twice to select [SCORE MODE].
65GB
Using the Sound Effect
Reinforcing bass frequencies
You can reinforce bass frequencies.
Press DYNAMIC BASS.
Bass frequencies are effectively reinforced.
To turn off the sound effect
Using the Sleep Timer
You can set the system to turn off at a preset
time, so you can fall asleep listening to music.
You can preset the time in 1 or 10-minutes
increments.
1
2
Press DYNAMIC BASS again.
3
Press SYSTEM MENU.
Press X/x repeatedly until “SLEEP”
appears in the front panel display, then
press
or c.
Press X/x to select a setting.
The minutes display (the remaining time)
changes as follows:
SLEEP 90M y SLEEP 80M y SLEEP 70M
Y
Y
SLEEP OFF y SLEEP 10M ..... SLEEP 60M
Tip
• You can select the remaining time by pressing
the number buttons. In this case, you can preset
the time in 1-minute increments.
4
Press
.
The setting is made and “SLEEP” lights up
in the front panel display.
5
Press SYSTEM MENU.
The system menu turns off.
To change the remaining time
Restart from Step 1.
To cancel the Sleep Timer
function
Select “SLEEP OFF” in Step 3.
66GB
Changing the Brightness
of the Front Panel Display
The brightness of the front panel display can be
set to either of 2 levels.
1
2
3
Press SYSTEM MENU.
Press X/x repeatedly until “DIMMER”
appears in the front panel display, then
press
or c.
Press X/x to select the brightness of
the front panel display.
4
Press
.
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
The DIGITAL MEDIA PORT (DMPORT)
adapter is for enjoying sound from a portable
audio source or computer. By connecting a
DIGITAL MEDIA PORT adapter, you can
enjoy sound from the connected component on
the system.
Available DIGITAL MEDIA PORT adapters
vary in each area.
For details on connecting the DIGITAL MEDIA
PORT adapter, see “Connecting Other
Components” (page 28).
Note
• Do not connect an adaptor other than the DIGITAL
MEDIA PORT adapter.
• Do not connect or disconnect the DIGITAL MEDIA
PORT adapter to/from the unit while the system is
turned on.
• Depending on the type of DIGITAL MEDIA PORT
adapter (not supplied), the images are also output. In
this case, the system outputs the composite video
signal only regardless of the type of video signal.
Other Operations
The default setting is underlined.
• “DIMMER OFF”: Bright.
• “DIMMER ON”: The front panel display
becomes dark.
Using the DIGITAL MEDIA
PORT Adapter
Playing the connected
component on the system
1
2
Press FUNCTION repeatedly until
“DMPORT” appears in the front panel
display.
Start playback of the connected
component.
The sound and images from the connected
component are played on the system or
connected TV.
For operation details, see the operating
instructions of the DIGITAL MEDIA
PORT adapter (not supplied).
Tip
• When listening to MP3 or other compressed music
using a portable audio source, you can enhance the
sound. Press SOUND FIELD repeatedly until
“A.F.D. STD” appears in the front panel display. To
cancel, select other than “A.F.D. STD.”
continued
67GB
Note
• Depending on the type of DIGITAL MEDIA PORT
adapter (not supplied), you may be able to operate a
connected component using either the buttons on the
remote or the unit. The following illustration shows
an example of buttons that can be used in this case.
Deactivating the Buttons
on the Unit
(Child Lock)
You can deactivate the buttons on the unit
(except for "/1) for preventing misoperation,
such as child mischief (child lock function).
When the child lock function is activated, the
buttons on the unit are locked and “
” lights
up in the front panel display. (You can operate
the system by using the remote.)
Note
• When you operate the buttons on the unit while the
child lock function is on, “CHILD LOCK” appears in
the front panel display.
./>
H
x
1
2
X
3
Press SYSTEM MENU.
Press X/x repeatedly until “CHILD
LOCK” appears in the front panel
display, then press
or c.
Press X/x to select a setting.
The default setting is underlined.
• “OFF”: Child lock function off.
• “ON”: Child lock function on.
4
Press
.
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
Tip
• You can activate the child lock function by pressing
x for more than 5 seconds (“
” lights up in the
front panel display).
To cancel, press x for more than 5 seconds so that
“
” disappears from the front panel display.
68GB
4
Advanced Settings and Adjustments
Press X/x to select [ON t], then press
.
x If you have not entered a password
The display for registering a new password
appears.
Locking Discs
(CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL)
PARENTAL CONTROL
Enter a new 4-digit password,
then press ENTER .
You can set two kinds of playback restrictions
for the desired disc.
• Custom Parental Control
You can set playback restrictions so that the
system will not play inappropriate discs.
• Parental Control
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. Scenes may be
blocked or replaced with different scenes.
The same password is used for both Custom
Parental Control and Parental Control.
Enter a 4-digit password using the number
buttons, then press .
The display for confirming the password
appears.
x When you have already registered a
password
Preventing playback of
specific discs [CUSTOM
PARENTAL CONTROL]
PARENTAL CONTROL
Enter password, then press
ENTER
.
You can set the same Custom Parental Control
password for up to 40 discs. When you set the
41st-disc, the first disc is canceled.
1
Insert the disc you want to lock.
If the disc is playing, press x to stop
playback.
2
5
Press
DISPLAY while the system is
in stop mode.
[Custom parental control is set.] appears
and the TV screen returns to the Control
Menu display.
The Control Menu display appears.
3
Enter or re-enter your 4-digit password
using the number buttons, then press
.
Press X/x to select
[PARENTAL CONTROL], then press
.
To turn off the Custom Parental
Control function
The options for [PARENTAL CONTROL]
appear.
1
Follow steps 1 through 3 of “Preventing
playback of specific discs [CUSTOM
PARENTAL CONTROL].”
2
Press X/x to select [OFF t], then press
.
3
Enter your 4-digit password using the
number buttons, then press
.
12(27)
18(34)
T
1:32:55
OFF
ON
PLAYER
PASSWORD
DVD VIDEO
Advanced Settings and Adjustments
The display for entering the password
appears.
continued
69GB
To play a disc for which Custom
Parental Control is set
1
12(27)
18(34)
T
1:32:55
Insert the disc for which Custom Parental
Control is set.
OFF
ON
PLAYER
PASSWORD
The [CUSTOM PARENTAL CONTROL]
display appears.
CUSTOM PARENTAL CONTROL
DVD VIDEO
3
Custom parental control is already
set. To play, enter your password
and press ENTER .
Press X/x to select [PLAYER t], then
press
.
x If you have not entered a password
The display for registering a new password
appears.
2
Enter your 4-digit password using the
number buttons, then press
.
PARENTAL CONTROL
The system is ready for playback.
Enter a new 4-digit password,
then press ENTER .
Tip
• If you forget your password, enter the 6-digit number
“199703” using the number buttons when the
[CUSTOM PARENTAL CONTROL] display asks
you for your password, then press
. The display
will ask you to enter a new 4-digit password.
Enter a 4-digit password using the number
buttons, then press .
The display for confirming the password
appears.
Limiting playback for children
[PARENTAL CONTROL]
x When you have already registered a
password
(DVD only)
The display for entering the password
appears.
Playback of some DVD VIDEOs can be limited
according to a predetermined level such as the
age of the users. The [PARENTAL CONTROL]
function allows you to set a playback limitation
level.
1
PARENTAL CONTROL
Enter password, then press
ENTER
.
Press
DISPLAY while the system is
in stop mode.
The Control Menu display appears.
2
Press X/x to select
[PARENTAL CONTROL], then press
.
The options for [PARENTAL CONTROL]
appear.
70GB
4
Enter or re-enter your 4-digit password
using the number buttons, then press
.
The display for setting the playback
limitation level appears.
PARENTAL CONTROL
LEVEL:
STANDARD:
5
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
PG13
USA
The lower the value, the stricter the
limitation.
Press X/x to select [STANDARD], then
press
.
The selection items for [STANDARD] are
displayed.
4:
To turn off the Parental Control
function
Set [LEVEL] to [OFF] in Step 8.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
USA
OTHERS
To play a disc for which Parental
Control is set
1
Insert the disc and press H.
The display for entering your password
appears.
Press X/x to select a geographic area
as the playback limitation level, then
press
.
The area is selected.
When you select [OTHERS t], select and
enter a standard code in the table of
“Parental Control Area Code List”
(page 95) using the number buttons.
7
Press X/x to select [LEVEL], then press
.
The selection items for [LEVEL] are
displayed.
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
OFF
8:
7:
6:
5:
8
NC17
R
Enter your 4-digit password using the
number buttons, then press
.
The system starts playback.
Tip
• If you forget your password, remove the disc and
repeat steps 1 to 3 of “Preventing playback of specific
discs [CUSTOM PARENTAL CONTROL].” When
you are asked to enter your password, enter “199703”
using the number buttons, then press
. The display
will ask you to enter a new 4-digit password. After
you enter a new 4-digit password, replace the disc in
the unit and press H. When the display for entering
your password appears, enter your new password.
Note
• When you play discs which do not have the Parental
Control function, playback cannot be limited on this
system.
• Depending on the disc, you may be asked to change
the parental control level while playing the disc. In
this case, enter your password, then change the level.
If the Resume Play mode is canceled, the level returns
to the previous level.
Advanced Settings and Adjustments
2
6
Press X/x to select the level you want,
then press
.
Parental Control setting is complete.
continued
71GB
Changing the password
1
Press
DISPLAY while the system is
in stop mode.
The Control Menu display appears.
2
Press X/x to select
[PARENTAL CONTROL], then press
.
The options for [PARENTAL CONTROL]
appear.
3
Press X/x to select [PASSWORD t],
then press
.
The display for entering the password
appears.
4
5
6
Enter your 4-digit password using the
number buttons, then press
.
Enter a new 4-digit password using the
number buttons, then press
.
Getting Optimal Surround
Sound for a Room
(SPEAKER FORMATION)
Depending on the shape of the room, there will
be some speakers you cannot install. For the
better surround sound, it is recommended that
first you decide the position of the speakers.
1
2
Press
DISPLAY when the system is
in stop mode.
The Control Menu display appears.
3
To confirm your password, re-enter it
using the number buttons, then press
.
Press X/x to select
FORMATION], then press
1(44)
3(28)
T
0:03:04
SPEAKER FORMATION
SPEAKER FORMATION
AUTO CALIBRATION
If you make a mistake entering
your password
Press C before you press
correct number.
Press FUNCTION repeatedly until
“DVD” appears in the front panel
display.
[SPEAKER
.
DVD VIDEO
and input the
4
Press X/x to select [SPEAKER
FORMATION], then press
.
The options for [SPEAKER
FORMATION] appear.
SPEAKER FORMATION
STANDARD
5
72GB
Press C/c to select a setting.
• [STANDARD]: when installing all the
speakers normally.
Note
• When the wireless kit WAHT-SD1 (not
supplied) is installed, [STANDARD
(WIRELESS)] appears instead.
• [ALL FRONT]: when installing all the
speakers in front of the listening position.
• [ALL FRONT - NO CENTER]: when
installing the front and surround speakers
in front of the listening position.
• [NO CENTER]: when installing the front
and surround speakers.
• [NO SURROUND]: when installing the
center and front speakers.
Note
• [FRONT ONLY]: when installing the
front speakers.
• Speaker sound in the other room is the same as
that of the front and surround speakers.
Advanced Settings and Adjustments
• [SECOND ROOM]: when installing the
front speakers in one room and surround
speakers in another.
Tip
• When the wireless kit WAHT-SD1 (not
supplied) is installed, [STANDARD (WIRED)]
appears.
continued
73GB
6
Press
.
The setting is made.
7
Press X/x to select [YES] or [NO], then
press
.
• [YES]: continue with [AUTO
CALIBRATION], see Step 4 of
“Calibrating the Appropriate Settings
Automatically” (page 74).
• [NO]: exit [SPEAKER FORMATION].
Calibrating the
Appropriate Settings
Automatically
(AUTO CALIBRATION)
D. C. A. C. (Digital Cinema Auto Calibration)
can set the appropriate surround sound
automatically.
SPEAKER FORMATION
Note
Continue with AUTO CALIBRATION?
YES
NO
Note
• In order to enjoy the surround sound after you change
the position of the speakers, it is recommended you
set [SPEAKER FORMATION], and then set [AUTO
CALIBRATION].
• To set [AUTO CALIBRATION], you need to
connect the supplied calibration mic.
• The front panel display indicates the selected
[SPEAKER FORMATION]. It does not indicate the
speakers which output sound.
• When you change the [CONNECTION] setting in
[SPEAKER SETUP], the [SPEAKER
FORMATION] setting returns to [STANDARD].
• Loud test sound is output when [AUTO
CALIBRATION] starts. You cannot turn the volume
down. Give consideration to children and neighbor.
1
2
Press FUNCTION repeatedly until
“DVD” appears in the front panel
display.
Press
DISPLAY when the system is
in stop mode.
The Control Menu display appears.
3
Press X/x to select
FORMATION], then press
1(44)
3(28)
T
0:03:04
SPEAKER FORMATION
SPEAKER FORMATION
AUTO CALIBRATION
4
[SPEAKER
.
DVD VIDEO
Press X/x to select [AUTO
CALIBRATION], then press
.
The options for [AUTO CALIBRATION]
appear.
AUTO CALIBRATION
Connect calibration mic. Start
measurement?
YES
NO
Connect the calibration mic to the A.CAL
MIC jack on the front panel, and set it up at
the ear level using a tripod, etc. (not
supplied). The front of each speaker should
74GB
face the calibration mic, and there should be
no obstruction between the speakers and the
calibration mic. Be quiet during the
measurement.
• The environment of the room in which the
system is installed may affect measurements.
• If an error message appears, follow the message,
then select [YES].
An error message appears when:
– the calibration mic is not connected.
– front speakers are not correctly connected.
– surround speakers are not correctly
connected.
– front and surround speakers are not correctly
connected.
– there is excessive noise around the
calibration mic.
– the calibration mic is overloaded.
AUDIO IN / MIC 1 /
A.CAL MIC
Calibration mic
6
Press C/X/x/c to select [YES] or [NO],
then press
.
x The measurement is OK.
Disconnect the calibration mic, then select
[YES]. The result is implemented.
YES
NO
x The measurement is not OK.
Follow the message, then select [YES] to
retry.
5
Press X/x to select [YES], then press
.
Measurement failure.
Calibration starts.
Check speaker connection.
Retry?
YES
NO
Measuring. Please wait a moment.
Advanced Settings and Adjustments
Measurement complete.
FRONT L :
YES
FRONT R :
YES
CENTER :
NONE
SUBWOOFER : YES
SURROUND L : NONE
SURROUND R : NONE
If OK, unplug calibration mic and select
“YES”.
Tip
• You can check the distance between the listening
position and each speaker. See page 81.
Note
Note
• Avoid being in the measurement area and
making noise during the measurement (about
three minutes), to avoid measurement failure.
During the measurement, test signals are output
from the speakers.
• While the Auto Calibration function works:
– do not turn off the power.
– do not press any button.
– do not change the volume.
– do not change the function.
– do not change the disc.
continued
75GB
– do not insert or eject a disc.
– do not disconnect the calibration mic.
• The measurement for [SUBWOOFER] is always
[YES] since the system does not perform subwoofer
calibration.
Using the Setup Display
By using the Setup Display, you can make
various adjustments to items such as picture and
sound.
For an overall list of Setup Display items, see
page 103.
Displayed items vary depending on the country
model.
Note
• Playback settings stored in the disc take priority over
the Setup Display settings and not all the functions
described may work.
1
2
Press FUNCTION repeatedly until
“DVD” appears in the front panel
display.
Press
DISPLAY when the system is
in stop mode.
The Control Menu display appears.
3
Press X/x to select
then press
.
[SETUP],
The options for [SETUP] appear.
12(27)
18(34)
T
0:00:02
DVD VIDEO
QUICK
QUICK
CUSTOM
RESET
BNR
4
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
5
76GB
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
Press X/x to select the setup item from
the displayed list: [LANGUAGE
SETUP], [SCREEN SETUP], [CUSTOM
SETUP], or [SPEAKER SETUP]. Then
press
.
1 while resetting the system as it takes a few
seconds to complete.
The Setup item is selected.
Example: [SCREEN SETUP]
Note
Selected item
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
4:3 OUTPUT:
• When you turn the system on after resetting and no
disc is in the unit, the guide message appears on the
TV screen. To perform the Quick Setup (page 19),
press
, to return to normal screen, press CLEAR.
16:9
ON
JACKET PICTURE
FULL
Setup items
6
Select an item using X/x, then press
.
The options for the selected item appear.
Example: [TV TYPE]
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
4:3 OUTPUT:
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
7
Select a setting using X/x, then press
.
The setting is selected and setup is
complete.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
4:3 OUTPUT:
4:3 LETTER BOX
ON
JACKET PICTURE
FULL
Selected setting
Advanced Settings and Adjustments
Options
To reset all of the [SETUP]
settings
1
2
Select [RESET] in Step 4 and press
.
Select [YES] using X/x.
You can also quit the process and return to the
Control Menu display by selecting [NO] here.
3
Press
.
All the settings explained on pages 78 to 83
return to the default settings. Do not press [/
77GB
Setting the Display or
Sound Track Language
[LANGUAGE SETUP]
[LANGUAGE SETUP] allows you to set
various languages for the on-screen display or
sound track.
Select [LANGUAGE SETUP] in the Setup
Display. For details, see “Using the Setup
Display” (page 76).
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
Settings for the Display
[SCREEN SETUP]
Choose settings according to the TV to be
connected.
Select [SCREEN SETUP] in the Setup Display.
For details, see “Using the Setup Display”
(page 76).
The default settings are underlined.
SCREEN SETUP
16:9
TV TYPE:
YCBCR
YCBCR/RGB (HDMI):
ON
SCREEN SAVER:
BACKGROUND:
JACKET PICTURE
FULL
4:3 OUTPUT:
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
x [TV TYPE]
x [OSD] (On-Screen Display)
Selects the aspect ratio of the connected TV (4:3
standard or wide).
Switches the display language on the TV screen.
x [MENU] (DVD VIDEO only)
[16:9]
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
[4:3 LETTER
BOX]
Select this when you connect a 4:3
screen TV. Displays a wide picture
with bands on the upper and lower
portions of the TV screen.
You can select the desired language for the
disc’s menu.
x [AUDIO] (DVD VIDEO only)
Switches the language of the sound track.
When you select [ORIGINAL], the language
given priority in the disc is selected.
[4:3 PAN SCAN] Select this when you connect a 4:3
x [SUBTITLE] (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select [AUDIO FOLLOW], the
language for the subtitles changes according to
the language you selected for the sound track.
screen TV. Automatically displays
the wide picture on the entire
screen and cuts off the portions
that do not fit.
[16:9]
Tip
• If you select [OTHERS t] in [MENU], [AUDIO],
and [SUBTITLE], select and enter a language code
from “Language Code List” (page 95) using the
number buttons.
[4:3 LETTER BOX]
Note
• When you select a language in [MENU], [AUDIO],
or [SUBTITLE] that is not recorded on the DVD
VIDEO, one of the recorded languages will be
automatically selected (depending on the disc, the
language may not be selected automatically).
78GB
[4:3 PAN SCAN]
x [4:3 OUTPUT]
Note
• Depending on the DVD, [4:3 LETTER BOX] may be
selected automatically instead of [4:3 PAN SCAN] or
vice versa.
x [YCBCR/RGB (HDMI)]
Selects the type of HDMI signal output from
HDMI OUT jack.
[YCBCR]
Outputs YCBCR signals.
[RGB]
Outputs RGB signals.
This setting is effective only when you set [TV
TYPE] in [SCREEN SETUP] to [16:9]
(page 78). Adjust to watch 4:3 aspect ratio
progressive signals. If you can change the aspect
ratio on your progressive format (525p/625p)
compatible TV, change the setting on your TV,
not the system. Note that this setting is effective
only for HDMI connection or progressive
signals output from the COMPONENT VIDEO
OUT jacks.
Note
Note
• If the playback picture becomes distorted, set
[YCBCR] to [RGB].
• If the HDMI OUT jack is connected to equipment
with a DVI jack, [RGB] signals will be automatically
output even when you select [YCBCR].
• This setting is effective only when
“PROGRESSIVE” is selected by using VIDEO
FORMAT (page 26).
Select this when you can change
the aspect ratio on your TV.
[NORMAL]
Select this when you cannot
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left and
right sides of the image.
x [SCREEN SAVER]
The screen saver image appears when you leave
the system in pause or stop mode for 15 minutes,
or when you play back a CD, DATA CD (MP3
audio), or DATA DVD (MP3 audio) for more
than 15 minutes. The screen saver will help
prevent your display device from becoming
damaged (ghosting). Press any button (e.g., H
button) to cancel the screen saver.
[ON]
Turns on the screen saver.
[OFF]
Turns off the screen saver.
x [BACKGROUND]
Selects the background color or picture on the
TV screen in stop mode or while playing a CD,
DATA CD (MP3 audio), or DATA DVD (MP3
audio).
[JACKET
PICTURE]
The jacket picture (still picture)
appears, but only when the jacket
picture is already recorded on the
disc (CD-EXTRA, etc.). If the
disc does not contain a jacket
picture, the [GRAPHICS] picture
appears.
[GRAPHICS]
A preset picture stored in the
system appears.
[BLUE]
The background color is blue.
[BLACK]
The background color is black.
16:9 aspect ratio TV
Advanced Settings and Adjustments
[FULL]
79GB
Custom Settings
[CUSTOM SETUP]
Use this to set up playback related and other
settings.
Select [CUSTOM SETUP] in the Setup Display.
For details, see “Using the Setup Display”
(page 76).
The default settings are underlined.
CUSTOM SETUP
OFF
HDMI CONTROL:
AUTO
PAUSE MODE:
OFF
TRACK SELECTION:
ON
MULTI-DISC RESUME:
OFF
AUDIO DRC:
OFF
AUDIO (HDMI):
Registration Code
DivX:
x [HDMI CONTROL]
Switches the HDMI CONTROL function on or
off. This function is available when you connect
the system and TV with the HDMI cord. For
details on this function, see the HDMI
CONTROL Guide (supplied separately).
[OFF]
Sets the HDMI CONTROL
function to off.
[ON]
Sets the HDMI CONTROL
function to on.
You can operate mutually
between components that are
connected with the HDMI cord.
Note
• When you set to [ON] without the HDMI connection
of the TV, [Please verify the HDMI connection]
appears and you can not set to [ON].
x [PAUSE MODE] (DVD VIDEO/DVD-R/
DVD-RW only)
x [TRACK SELECTION] (DVD VIDEO only)
Gives the sound track which contains the highest
number of channels priority when you play a
DVD VIDEO on which multiple audio formats
(PCM, DTS, MPEG audio, or Dolby Digital
format) are recorded.
[OFF]
No priority given.
[AUTO]
Priority given.
Note
• When you set the item to [AUTO], the language may
change. The [TRACK SELECTION] setting has
higher priority than the [AUDIO] settings in
[LANGUAGE SETUP] (page 78). (Depending on
the disc, this function may not work.)
• If PCM, DTS, Dolby Digital sound, and MPEG audio
tracks have the same number of channels, the system
selects PCM, DTS, Dolby Digital sound, and MPEG
audio tracks in this order.
x [MULTI-DISC RESUME] (DVD VIDEO/
VIDEO CD only)
Switches the Multi-disc Resume setting on or
off.
[ON]
Stores the resume settings in
memory for up to 40 discs.
[OFF]
Does not store the resume settings
in memory. Playback restarts at
the resume point only for the
current disc in the unit.
x [AUDIO DRC] (DVD VIDEO only)
Narrows the dynamic range of the sound track.
Useful for watching movies at low volume late
at night.
[OFF]
No compression of dynamic
range.
[STANDARD]
Reproduces the sound track with
the kind of dynamic range that the
recording engineer intended.
[MAX]
Compresses dynamic range fully.
Selects the picture in pause mode.
[AUTO]
[FRAME]
80GB
The picture, including subjects
that move dynamically, is output
with no jitter. Normally select this
position.
x [AUDIO (HDMI)]
The picture, including subjects
that do not move dynamically, is
output in high resolution.
[OFF]
Selects the audio output status from the HDMI
OUT jack.
The sound is not output from the
HDMI OUT jack.
[ON]
Outputs audio signals by
converting Dolby Digital, DTS, or
96 kHz/24 bit PCM signals to 48
kHz/ 16 bit PCM.
Note
• When you connect the unit and TV with the HDMI
cord and [ON] is selected, DYNAMIC BASS,
MOVIE/MUSIC, and sound field are not applied to
the sound that is output from the TV.
x [DivX]
Displays the registration code for this system.
For more information, go to
http://www.divx.com on the Internet.
Settings for the Speakers
[SPEAKER SETUP]
To obtain the best possible surround sound, set
connection of the speakers and their distance
from your listening position. Then use the test
tone to adjust the level and the balance of the
speakers to the same level.
Select [SPEAKER SETUP] in the Setup
Display. For details, see “Using the Setup
Display” (page 76).
The default settings are underlined.
YES
YES
YES
YES
To return to the default setting
when changing a setting
Select the item, then press CLEAR. Note that
only the [CONNECTION] setting does not
return to the default setting.
x [CONNECTION]
If you do not connect center or surround
speakers, set the parameters for [CENTER] and
[SURROUND]. Since the front speaker and
subwoofer setting is fixed, you cannot change
them.
[FRONT]
[YES]
[CENTER]
[YES]: Normally select this.
[NONE]: Select this if no center
speaker is used.
[SURROUND]
[YES]: Normally select this.
[NONE]: Select this if no
surround speaker is used.
[SUBWOOFER]
[YES]
Advanced Settings and Adjustments
SPEAKER SETUP
CONNECTION:
DISTANCE(FRONT):
DISTANCE(SURROUND):
LEVEL(FRONT):
LEVEL(SURROUND):
OFF
TEST TONE:
FRONT:
CENTER:
SURROUND:
SUBWOOFER:
Note
• When you change the [CONNECTION] setting, the
[SPEAKER FORMATION] setting returns to
[STANDARD].
continued
81GB
x [DISTANCE (FRONT)]
The default distance setting for the speakers in
relation to the listening position is shown below.
When you set the distance using the Quick Setup
(page 19), the settings is automatically
displayed.
0.0 - 7.0 m2)/
0 - 23 ft
1.0 - 7.0 m3)/
3 - 23 ft
0.0 - 7.0 m2)/
0 - 23 ft
Be sure to change the value in the Setup Display
when you move the speakers.
[L/R]
3.0 m/10 ft1)
Be sure to change the value in the Setup Display
when you move the speakers.
[L/R]
3.0 m/10 ft1)
Front speaker distance from the
listening position can be set from
1.0 to 7.0 meters3) (3 to 23 ft).
[CENTER]
3.0 m/10 ft1)
Center speaker distance can be
moved up to 1.6 meters (5 ft)
(appears when you closer to the listening position
set [CENTER] to from the front speaker distance.
[YES] in the
[CONNECTION]
setting.)
1)When
you perform the Quick Setup (page 19), the
default settings are changed.
2)0.0
3)
to 6.9 meters for North American models.
0.9 to 6.9 meters for North American models.
x [DISTANCE (SURROUND)]
The default distance setting for the speakers in
relation to the listening position is shown below.
When you set the distance using the Quick Setup
(page 19), the settings is automatically
displayed.
Surround speakers distance
can be moved up to 5.0 meters
(appears when you (16 ft) closer to the listening
set [SURROUND] to position from the front speaker
[YES] in the
distance.
[CONNECTION]
setting.)
1)When
you perform the Quick Setup (page 19), the
default settings are changed.
2)
0.0 to 6.9 meters for North American models.
Note
• If all front and surround speakers are not placed at an
equal distance from your listening position, set the
distance according to the closest speaker.
• Do not place the surround speakers farther away from
your listening position than the front speakers.
• Depending on the input stream, the [DISTANCE]
setting may not be effective.
x [LEVEL (FRONT)]
You can vary the level of front speakers as
follows. Be sure to set [TEST TONE] to [ON]
for easy adjustment.
[L/R]
0.0 dB
Set this between –6.0 dB and
0.0 dB.
[CENTER]
0.0 dB
Set this between –6.0 dB and
+6.0 dB.
(appears when you
set [CENTER] to
[YES] in the
[CONNECTION]
setting.)
82GB
[SUBWOOFER]
0.0 dB
Set this between –6.0 dB and
+6.0 dB.
x [LEVEL (SURROUND)]
You can vary the level of surround speakers as
follows. Be sure to set [TEST TONE] to [ON]
for easy adjustment.
[L/R]
0.0 dB
(appears when you
set [SURROUND]
to [YES] in the
[CONNECTION]
setting.)
6
Press X/x repeatedly to select [TEST
TONE], then press
or c.
Press X/x repeatedly to select [ON],
then press
.
You will hear the test tone from each
speaker in sequence.
7
Set this between –6.0 dB and
+6.0 dB.
From your listening position, adjust the
value of [LEVEL (FRONT)] or [LEVEL
(SURROUND)] using C/X/x/c.
The test tone is emitted from only the
speaker which you are adjusting.
8
To adjust the volume of all the
speakers at one time
Turn the VOLUME control on the unit, or press
VOLUME +/– on the remote.
9
Press
when you have finished
making adjustments.
Press X/x repeatedly to select [TEST
TONE], then press
.
10 Press X/x repeatedly to select [OFF],
then press
.
Note
x [TEST TONE]
[OFF]
The test tone is not emitted from the
speakers.
[ON]
The test tone is emitted from each speaker
in sequence while adjusting level. When
you select one of the [SPEAKER SETUP]
items, the test tone is emitted from each
speaker in sequence.
Adjusting the speaker level by
using the test tone
Press
DISPLAY when the system is
in stop mode.
Advanced Settings and Adjustments
• The test tone signals are not output from the HDMI
OUT jack.
The speakers will emit a test tone to adjust
[LEVEL (FRONT)] and [LEVEL
(SURROUND)].
1
5
The Control Menu display appears.
2
Press X/x to select
then press
.
[SETUP],
The options for [SETUP] appear.
3
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
4
Press X/x repeatedly to select
[SPEAKER SETUP], then press
c.
or
83GB
Returning to the Default
Settings
You can return the system parameters, such as
preset stations, to the default settings.
"/1
1
2
A
x
Press "/1 to turn on the system.
Press x, A, and "/1 on the unit at the
same time.
“COLD RESET” appears in the front panel
display and the default settings are returned.
84GB
On adjusting volume
Additional Information
Precautions
• Do not turn up the volume while listening to a section
with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
section is suddenly played.
On power sources
On cleaning
• Unplug the unit from the wall outlet if you do not
intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never by
the cord.
• Clean the cabinet, panel, and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any questions or problems concerning
your system, please consult your nearest Sony dealer.
On placement
On operation
• If the system is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lenses inside the control unit.
Should this occur, the system may not operate
properly. In this case, remove the disc and leave the
system turned on for about half an hour until the
moisture evaporates.
• When you move the system, take out any disc. If you
don’t, the disc may be damaged.
• If anything falls into the cabinet, unplug the unit and
have it checked by qualified personnel before
operating it any further.
On cleaning discs, disc/lens
cleaners
• Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause
the apparatus to malfunction.
On your TV’s color
• If the speakers should cause the TV screen to have
color irregularity, turn off the TV then turn it on after
15 to 30 minutes. If color irregularity should persist,
place the speakers further away from the TV set.
IMPORTANT NOTICE
Caution: This system is capable of holding a still
video image or on-screen display image on your
television screen indefinitely. If you leave the still
video image or on-screen display image displayed
on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to
this.
Additional Information
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• At high volume, over long periods of time, the cabinet
becomes hot to the touch. This is not a malfunction.
However, touching the cabinet should be avoided. Do
not place the unit in a confined space where
ventilation is poor as this may cause overheating.
• Do not block the ventilation slots by putting anything
on the system. The system is equipped with a high
power amplifier. If the ventilation slots are blocked,
the unit can overheat and malfunction.
• Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation slots.
• Do not install the unit near heat sources such as
radiators, or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration, or
shock.
• Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position only.
• Keep the unit and discs away from equipment with
strong magnets, such as microwave ovens, or large
loudspeakers.
• Do not place heavy objects on the unit.
On moving the system
Before moving the system, make sure that there is no
disc inserted, and remove the AC power cord (mains
lead) from the wall outlet (mains).
85GB
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
Troubleshooting
If you experience any of the following
difficulties while using the system, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should any
problem persist, consult your nearest Sony
dealer.
Note that if service personnel changes some
parts during repair, these parts may be retained.
Power
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning
cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
This system can only play back a standard
circular disc. Using neither standard nor circular
discs (e.g., card, heart, or star shape) may cause
a malfunction.
Do not use a disc that has a commercially
available accessory attached, such as a label or
ring.
86GB
The power is not turned on.
• Check that the AC power cord (mains lead) is
connected securely.
• Press "/1 after “STANDBY” disappears from the
front panel display.
If “PROTECTOR” and “PUSH POWER” appear
alternately in the front panel display.
Press "/1 to turn off the system, and check the
following items after “STANDBY” disappears.
• Are the + and – speaker cords short-circuited?
• Are you using only the specified speakers?
• Is anything blocking the ventilation holes of the
system?
After checking the above items and fixing any
problems, turn on the system. If the cause of the
problem cannot be found even after checking all the
above items, consult your nearest Sony dealer.
Picture
There is no picture.
• The video connecting cords are not connected
securely.
• The video connecting cords are damaged.
• The unit is not connected to the correct TV input
jack (page 14, 24).
• The video input on the TV is not set so that you
can view pictures from the system.
• You have set progressive format but your TV
cannot accept the signal in progressive format. In
this case, return the setting to interlace format (the
default setting) (page 26).
• Even if your TV is compatible with progressive
format (525p/625p) signals, the image may be
affected when you set progressive format. In this
case, return the setting to interlace format (the
default setting) (page 26).
• Re-connect the connecting cord securely.
• The unit is connected to an input device that is not
HDCP (high-bandwidth digital content
Picture noise appears.
• The disc is dirty or flawed.
• If the picture output from your system goes
through your VCR to get to your TV, the copyprotection signal applied to some DVD programs
could affect picture quality. If you still experience
problems even when you connect your unit
directly to your TV, try connecting your unit to
your TV’s S video input (page 24).
Even though you set the aspect ratio in [TV
TYPE] of [SCREEN SETUP], the picture does
not fill the TV screen.
• The aspect ratio on the disc is fixed.
Color irregularity occurs on the TV screen.
The subwoofer and the front speakers in this system
are magnetically shielded to prevent magnetic
leakage. However, some leakage may occur, as a
high-strength magnet is employed. If this happens,
check the following items:
• If the speakers are used with a CRT-based TV or
projector, install the speakers at least 0.3 meters
(1.0 ft) from the TV set.
• If the color irregularity persists, turn off the TV set
once, then turn it on after 15 to 30 minutes.
• If howling occurs, reposition the speakers farther
away from the TV set.
• Make sure that no magnetic object (magnetic latch
on a TV stand, health care device, toy, etc.) is
placed near the speakers.
Sound
There is no sound.
• The speaker cord is not connected securely.
• Press MUTING on the remote if “MUTING ON”
is displayed in the front panel display.
• The system is in pause mode or in Slow-motion
Play mode. Press H to return to normal play
mode.
• Fast forward or fast reverse is performed. Press
H to return to normal play mode.
• Check the speaker settings (page 81).
• The equipment connected to the HDMI OUT jack
does not conform to the audio signal format, in
this case set [AUDIO (HDMI)] in [CUSTOM
SETUP] to [ON] (page 80).
No sound is output from the HDMI OUT jack.
• Set [AUDIO (HDMI)] in [CUSTOM SETUP] to
[ON] (page 80).
• The HDMI OUT jack is connected to a DVI
(digital visual interface) device (DVI (digital
visual interface) jacks do not accept audio
signals).
• Try the following: 1 Turn the system off and on
again. 2 Turn the connected equipment off and
on again. 3 Disconnect and then connect the
HDMI cord again.
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected correctly and securely.
Additional Information
protection) compliant (“HDMI” on the front panel
does not light up). See page 98.
• If the HDMI OUT jack is used for video output,
changing the type of video signal output from the
HDMI OUT jack by pressing VIDEO FORMAT
may solve the problem (page 25).
Connect the TV and the unit using a video jack
other than the HDMI OUT, and switch the TV’s
input to the connected video input so that you can
see the on-screen displays. Change the type of
video signal output from the HDMI OUT jack,
and switch the TV’s input back to HDMI. If the
picture still does not appear, repeat the steps and
try other options.
• You have selected “PROGRESSIVE” using the
VIDEO FORMAT button on the remote
(“PROGRE” lights up in the front panel display)
even though your TV cannot accept the
progressive signal. In this case, disconnect the
HDMI cord from the unit and then select
“INTERLACE” so that “PROGRE” turns off.
• If the signal from the S VIDEO OUT jack is
distorted, change the type of video signal output
from the HDMI OUT jack by pressing VIDEO
FORMAT to [720 × 480p]* (page 25).
* Depending on the country, [720 × 576p] may
appear.
There is no sound from the subwoofer.
• Check the speaker connections and settings (page
14, 81).
• Set the sound field to “A.F.D. STD” (page 34).
Severe hum or noise is heard.
• Check that the speakers and components are
connected securely.
• Check that the connecting cords are away from a
transformer or motor, and at least 3 meters (10 ft)
away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
• Clean the disc.
continued
87GB
The sound loses stereo effect when you play a
VIDEO CD, a CD, or an MP3.
• Set [AUDIO] to [STEREO] by pressing AUDIO
(page 43).
• Make sure the unit is connected properly.
The surround effect is difficult to hear when
you are playing a Dolby Digital, DTS, or MPEG
audio sound track.
• Make sure the sound field function is on (page 34).
• Check the speaker connections and settings (page
14, 81).
• Depending on the DVD, the output signal may not
be the entire 5.1 channel. It may be monaural or
stereo even if the sound track is recorded in Dolby
Digital or MPEG audio format.
The sound comes from the center speaker
only.
• Depending on the disc, the sound may come from
the center speaker only.
No sound is heard from the center speaker.
• Check the speaker connections and settings (page
14, 81).
• Make sure the sound field function is on (page 34).
• Depending on the source, the effect of the center
speaker may be less noticeable.
• A 2 channel source is being played.
No sound or only a very low-level sound is
heard from the surround speakers.
• Check the speaker connections and settings (page
14, 81).
• Make sure the sound field function is on (page 34).
• Depending on the source, the effect of the
surround speakers may be less noticeable.
• A 2 channel source is being played.
Microphone sound is not output.
• A function other than DVD is selected.
• The microphone is not connected to the unit
properly.
• The microphone volume is set to minimum.
There is no sound from the speakers that are
indicated in the front panel display.
• The front panel display indicates the selected
[SPEAKER FORMATION]. It does not indicate
the speakers which output sound (page 34, 72).
Operation
Radio stations cannot be tuned in.
• Check that the antenna (aerial) is connected
securely. Adjust the antenna (aerial) or connect an
external antenna (aerial) if necessary.
88GB
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
preset stations). Preset the stations (page 58).
• Press DISPLAY so that the frequency appears in
the front panel display.
The remote does not function.
• There are obstacles between the remote and the
unit.
• The distance between the remote and the unit is
too far.
• The remote is not pointed at the remote sensor on
the unit.
• The batteries in the remote are weak.
The disc does not play.
• There is no disc inserted.
• The disc is upside down.
Insert the disc with the playback side facing down.
• The disc is skewed on the disc tray.
• The system cannot play CD-ROMs, etc. (page 5).
• The region code on the DVD does not match the
system.
• Moisture has condensed inside the unit and may
cause damage to the lenses. Remove the disc and
leave the unit turned on for about half an hour.
The MP3 audio track cannot be played.
• The DATA CD is not recorded in the MP3 format
that conforms to ISO 9660 Level 1/Level 2, or
Joliet.
• The DATA DVD is not recorded in an MP3
format that conforms to UDF (Universal Disk
Format).
• The MP3 audio track does not have the extension
“.MP3.”
• The data is not formatted in MP3 even though it
has the extension “.MP3.”
• The data is not MPEG1 Audio Layer 3 data.
• The system cannot play audio tracks in MP3PRO
format.
• The [MODE (MP3, JPEG)] setting has been set to
[IMAGE (JPEG)] (page 53).
• If you cannot change the [MODE (MP3, JPEG)]
setting, re-load the disc or turn the system off, then
on.
• The DATA CD/DATA DVD contains a DivX
video file.
The JPEG image file cannot be played.
• The DATA CD is not recorded in a JPEG format
that conforms to ISO 9660 Level 1/Level 2, or
Joliet.
• The DATA DVD is not recorded in a JPEG format
that conforms to UDF (Universal Disk Format).
• It has an extension other than “.JPEG” or “.JPG.”
• It is larger than 3,072 (width) × 2,048 (height) in
normal mode, or more than 2,000,000 pixels in
Progressive JPEG which is mainly used on the
Internet WEB site.
• It does not fit the TV screen (those images are
reduced).
• The [MODE (MP3, JPEG)] setting has been set to
[AUDIO (MP3)] (page 53).
• If you cannot change the [MODE (MP3, JPEG)]
setting, re-load the disc or turn the system off, then
on.
• The DATA CD/DATA DVD contains a DivX
video file.
The MP3 audio tracks and JPEG image file
starts playing simultaneously.
• [AUTO] has been selected in [MODE (MP3,
JPEG)] (page 53).
The titles of album/track/file name are not
displayed correctly.
• The system can only display numbers and letters
of the alphabets. Other characters are displayed as
[*].
A disc does not start playing from the
beginning.
• Program Play, Shuffle Play, or Repeat Play has
been selected.
Press CLEAR to cancel these functions before
playing a disc.
• Resume Play has been selected.
During stop, press x on the unit or the remote and
then start playback (page 38).
• The title, DVD or PBC menu automatically
appears on the TV screen.
The system starts playing the disc
automatically.
• The DVD features an auto playback function.
You cannot perform some functions such as
Stop, Search, Slow-motion Play, or Repeat
Play.
• Depending on the disc, you may not be able to
perform some of the operations above. See the
operating instructions that came with the disc.
Messages do not appear on the TV screen in
the language you want.
• In the Setup Display, select the desired language
for the on-screen display in [OSD] under
[LANGUAGE SETUP] (page 78).
The language for the sound track cannot be
changed.
• Multilingual tracks are not recorded on the DVD
being played.
• The DVD prohibits changing the language for the
sound track.
The subtitle language cannot be changed.
• Multilingual subtitles are not recorded on the
DVD being played.
• The DVD prohibits changing the subtitles.
The subtitle cannot be turned off.
• The DVD prohibits turning off subtitles.
The angles cannot be changed.
• Multi-angles are not recorded on the DVD being
played (page 48).
• The DVD prohibits changing the angles.
A disc cannot be ejected and “LOCKED”
appears in the front panel display.
• Contact your Sony dealer or local authorized Sony
service facility.
Additional Information
The DivX video file cannot be played.
• The file is not created in DivX format.
• The file has an extension other than “.AVI” or
“.DIVX.”
• The DATA CD/DATA DVD is not created in a
DivX format that conforms to ISO 9660 Level 1/
Level 2 or, Joliet/UDF.
• The DivX video file is larger than 720 (width) ×
576 (height).
Playback stops automatically.
• Some discs may contain an auto pause signal.
While playing such a disc, the system stops
playback at the auto pause signal.
[Data error] appears on the TV screen when
playing a DATA CD or DATA DVD.
• The MP3 audio track/JPEG image file/DivX
video file you want to play is broken.
• The data is not MPEG1 Audio Layer 3 data.
• The JPEG image file format does not conform to
DCF.
• The JPEG image file has the extension “.JPG” or
“.JPEG,” but is not in JPEG format.
• The file you want to play has the extension “.AVI”
or “.DIVX” but is not in DivX format, or is in
DivX format but does not conform to a DivX
Certified profiles.
continued
89GB
The system does not work normally.
• Disconnect the AC power cord (mains lead) from
the wall outlet (mains), then reconnect after
several minutes.
The unit does not work and “CHILD LOCK”
appears in the front panel display when you
press any button on the unit.
• Set the child lock function to off (page 68).
The HDMI CONTROL function does not work.
• When “HDMI” does not light up in the front panel
display, check the HDMI connection (page 24).
• Set the [HDMI CONTROL] setting in [CUSTOM
SETUP] to [ON] (page 80).
• Make sure that the connected component is
compatible with the HDMI CONTROL function.
• Check that the AC power cord (mains lead) of the
connected component is connected securely.
• Check the connected component’s setting for the
HDMI CONTROL function. See the operating
instructions of the component.
• If you change the HDMI connection, connect and
disconnect the AC power cord (mains lead), or
have a power failure, set the [HDMI CONTROL]
setting in [CUSTOM SETUP] to [OFF], then set
the [HDMI CONTROL] setting in [CUSTOM
SETUP] to [ON] (page 80).
• For details on the HDMI CONTROL function, see
the HDMI CONTROL Guide (supplied
separately).
No sound is output from the system and TV
while using the System Audio Control
function.
• Set the [AUDIO (HDMI)] setting in [CUSTOM
SETUP] to [ON] (page 80).
• Make sure that the connected TV is compatible
with the System Audio Control function.
• For details on the System Audio Control function,
see the HDMI CONTROL Guide (supplied
separately).
Self-diagnosis Function
(When letters/numbers appear in the
display)
When the self-diagnosis function is activated to
prevent the system from malfunctioning, a 5character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the TV screen or front panel display. In this case,
check the following table.
C:13:50
First 3
characters of
the service
number
Cause and/or corrective action
C 13
The disc is dirty.
,Clean the disc with a soft cloth
(page 86).
C 31
The disc is not inserted correctly.
,Restart the system, then re-insert
the disc correctly.
E XX
To prevent a malfunction, the
(xx is a number) system has performed the selfdiagnosis function.
,Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5character service number.
Example: E 61 10
When displaying the version
number on the TV screen
When you turn on the system, the version
number [VER.X.XX] (X is a number) may
appear on the TV screen. Although this is not a
malfunction and for Sony service use only,
normal system operation will not be possible.
Turn off the system, and then turn on the system
again to operate.
VER.X.XX
90GB
Specifications
Other models:
Amplifier section
Stereo mode (rated)
108 W + 108 W (at 3 ohms,
1 kHz, 1 % THD)
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*: 142 watts
(per channel at 3 ohms, 1
kHz, 10 % THD)
Subwoofer*: 140 watts (at
3 ohms, 80 Hz, 10 % THD)
Antenna (aerial)
Intermediate frequency
Video section
Outputs
* Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analog)
TV/VIDEO (AUDIO IN) Sensitivity: 450/250 mV
AUDIO IN/MIC 1
Sensitivity:
AUDIO IN 250/125 mV/
MIC 1 1 mV
MIC 2
Sensitivity: 1 mV
Laser
HDMI OUT: Type A (19
pin)
Speakers
Front (SS-TS73)
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
Tuner section
System
FM tuner section
Tuning range
North American models:
PLL quartz-locked digital
synthesizer
87.5-108.0 MHz (100 kHz
step)
Other models:
87.5-108.0 MHz (50 kHz
step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
North American, Mexican, and Latin American
models:
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
European, Russian, and Middle Eastern models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
Australian and New Zealand models:
531 – 1,710 kHz (with the
interval set at 9 kHz)
Bass reflex, magnetically
shielded
65 mm dia, cone type
3.0 ohms
93 × 539 × 75 mm (w/h/d)
300 × 1,039 - 1,230 × 300
mm (w/h/d) with stand
1.2 kg
3.0 kg with stand
Center (SS-CT71)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
Bass reflex, magnetically
shielded
65 mm dia, cone type
3.0 ohms
261 × 91 × 80 mm (w/h/d)
0.7 kg
Additional Information
Signal format system
Semiconductor laser
(DVD: λ = 650 nm)
(CD: λ = 790 nm)
Emission duration:
continuous
PAL/NTSC
VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.7 Vp-p
75 ohms
Speaker system
DVD system
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,602 kHz (with the
interval set at 9 kHz)
530 – 1,610 kHz (with the
interval set at 10 kHz)
AM loop antenna (aerial)
450 kHz
Surround (SS-TS71)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
Bass reflex, magnetically
shielded
65 mm dia, cone type
3.0 ohms
93 × 162 × 75 mm (w/h/d)
0.6 kg
Subwoofer (SS-WS72)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
Bass reflex
160 mm dia, cone type
3.0 ohms
220 × 394 × 350 mm
(w/h/d)
6.5 kg
continued
91GB
General
Power requirements
Power consumption
220 – 240 V AC, 50/60 Hz
On: 150 W
Standby: 0.3 W (at the
Power Saving mode)
Output voltage (DIGITAL MEDIA PORT)
DC 5 V
Output current (DIGITAL MEDIA PORT)
700 mA
Dimensions (approx.)
430 × 63 × 380 mm (w/h/d)
incl. projecting parts
Mass (approx.)
4.1 kg
Design and specifications are subject to change
without notice.
Unpacking
• Front speakers (2)
• Center speaker (1)
• Surround speakers (2)
• Subwoofer (1)
• AM loop antenna (aerial) (1)
• FM wire antenna (aerial) (1)
• Speaker cords (6, red/white/green/gray/blue/purple)
• Video Cord (1)
• Remote Commander (remote) (1)
• R6 (size AA) batteries (2)
• Calibration mic (1)
• Foot pads (1 set)
• Posts (2)
• Bases (2)
• Mounting plates (2)
• Post covers (2)
• Screws (large, with washer) (8)
• Screws (small, silver) (4)
• Screws (small, black) (2)
• Microphone (1)
• Operating Instructions
• HDMI CONTROL Guide
• Speaker and TV connections (card)
•Standby power consumption 0.3 W (or
less).
•Halogenated flame retardants are not
used in the printed wiring boards.
•Over 85 % power efficiency of
amplifier block is achieved with the
full digital amplifier, S-master.
92GB
Glossary
Album
Section of a music piece or an image on a data
CD containing MP3 audio tracks or JPEG files.
Chapter
Subdivision of a title on a DVD. A title is
composed of several chapters.
Digital Cinema Auto Calibration
Digital Cinema Auto Calibration was developed
by Sony to automatically measure and adjusts
the speaker settings to your listening
environment in a short period of time.
DivX®
Digital video technology created by DivX, Inc.
Videos encoded with DivX technology are
among the highest quality with a relatively small
file size.
Dolby Digital
This movie theater sound format is more
advanced than Dolby Surround Pro Logic. In
this format, the surround speakers output stereo
sound with an expanded frequency range, and a
subwoofer channel for deep bass is
independently provided. This format is also
called “5.1” with the subwoofer channel
designed as the 0.1 channel (since it functions
only when a deep bass effect is needed). All six
channels in this format are recorded separately
for superior channel separation. Furthermore,
since all the signals are processed digitally, less
signal degradation occurs.
Dolby Pro Logic II
Dolby Pro Logic II creates five full-bandwidth
output channels from 2 channel sources. This is
done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
x Movie mode
The Movie mode is for use with stereo television
shows and all programs encoded in Dolby
Surround. The result is enhanced sound field
directionality that approaches the quality of
discrete 5.1-channel sound.
x Music mode
DVD+RW
The Music mode is for use with any stereo music
recordings, and provides a wide and deep sound
space.
A DVD+RW (plus RW) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
Dolby Surround Pro Logic
As one method of decoding Dolby Surround,
Dolby Surround Pro Logic produces four
channels from 2 channel sound. Compared with
the former Dolby Surround system, Dolby
Surround Pro Logic reproduces left-to-right
panning more naturally and localizes sounds
more precisely. To take full advantage of Dolby
Surround Pro Logic, you should have one pair of
surround speakers and a center speaker. The
surround speakers output monaural sound.
DVD-RW
DTS
A JPEG image or a DivX video recorded on a
DATA CD/DATA DVD. (“File” is an exclusive
definition for this system.) A single file consists
of a single image or movie.
DVD
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same as
a CD.
The data capacity of a single-layer and singlesided DVD, at 4.7 GB (Giga Byte), is 7 times
that of a CD. Furthermore, the data capacity of a
dual-layer and single-sided DVD is 8.5 GB, a
single-layer and double-sided DVD 9.4 GB, and
a dual-layer and double-sided DVD 17 GB.
The picture data uses the MPEG 2 format, one of
a worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 of its original size. The DVD also
uses the variable rate coding technology that
processes allocated data according to the status
of the picture.
The audio data is recorded in Dolby Digital as
well as in PCM, allowing you to enjoy more
realistic audio presence.
Furthermore, various advanced functions such
as the multi-angle, multilingual, and Parental
Control functions are provided with the DVD.
File
Film based software, Video based
software
DVDs can be classified as Film based or Video
based software. Film based DVDs contain the
same images (24 frames per second) that are
shown at movie theaters. Video based DVDs,
such as television dramas or sit-coms, displays
images at 30 frames (or 60 fields) per second.
HDMI (high-definition multimedia
interface)
HDMI is an interface that supports both video
and audio on a single digital connection,
allowing you to enjoy high quality digital
picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital
Contents Protection), a copy protection
technology that incorporates coding technology
for digital video signals.
Additional Information
Digital audio compression technology
developed by DTS, Inc. This technology
conforms to 5.1-channel surround. This format
comprises of stereo rear channel and there is
discrete subwoofer channel in this format. DTS
provides the same 5.1 discrete channels of high
quality digital audio. The good channel
separation is realized due to the all channel data
being recorded discretely and processed in
digitally.
A DVD-RW is a recordable and rewritable disc
that is the same size as a DVD VIDEO. The
DVD-RW has two different modes: VR mode
and Video mode. DVD-RWs created in Video
mode have the same format as a DVD VIDEO,
while discs created in VR (Video Recording)
mode allow the contents to be programmed or
edited.
Interlace format
(Interlaced scanning)
The Interlace format is the NTSC standard
method for displaying TV images at 30 frames
per second. Each frame is scanned twice alternately between the even numbered scanning
lines and then odd numbered scanning lines, at
60 times per second.
continued
93GB
MPEG audio
Region Code
A coding system to compress digital audio
signals. MPEG-1 is used for MP3 (MPEG-1
Audio Layer-3). MPEG-2 is used for one of the
audio format of DVD.
This system is used to protect copyrights. A
region number is allocated on each DVD system
or DVD disc according to the sales region. Each
region code is shown on the system as well as on
the disc packaging. The system can play discs
that match its region code. The system can also
play discs with the “ ” mark. Even when the
region code is not shown on the DVD, the region
limit may still apply.
Multi-angle function
Various angles of a scene, or viewpoints of the
video camera are recorded on some DVDs.
Multilingual function
Several languages for the sound or subtitles in a
picture are recorded on some DVDs.
Parental Control
A function of the DVD to limit playback of the
disc by the age of the users according to the
limitation level in each country. The limitation
varies from disc to disc; when it is activated,
playback is completely prohibited, violent
scenes are skipped or replaced with other scenes
and so on.
PCM (Pulse Code Modulation)
A method for converting analog audio to digital
audio. It is used for the Compact Disc (CD)
audio format.
Playback Control (PBC)
Signals encoded on VIDEO CDs (Version 2.0)
to control playback.
By using menu screens recorded on VIDEO
CDs with PBC functions, you can enjoy playing
simple interactive programs, programs with
search functions, and so on.
Progressive format
(sequential scanning)
In contrast to the Interlace format, the
progressive format can reproduce 50 - 60 frames
per second by reproducing all scanning lines
(525 lines for the NTSC system, 625 lines for the
PAL system). The overall picture quality
increases and still images, text and horizontal
lines appear sharper. This format is compatible
with the 525 or 625 progressive format.
94GB
ALL
Scene
On a VIDEO CD with PBC (playback control)
functions, the menu screens, moving pictures
and still pictures are divided into sections called
“scenes.”
Title
The longest section of a picture or music feature
on a DVD, movie, etc., in video software, or the
entire album in audio software.
Track
Section of a picture or a music piece on a
VIDEO CD, CD, or MP3. An album is
composed of several tracks (MP3 only).
VIDEO CD
A compact disc that contains moving pictures.
The picture data uses the MPEG 1 format, one of
a worldwide standard of digital compression
technology. The picture data is compressed to
about 1/140 of its original size. Consequently, a
12 cm VIDEO CD can contain up to 74 minutes
of moving pictures.
VIDEO CDs also contain compact audio data.
Sounds outside the range of human hearing are
compressed while sounds we can hear are not
compressed. VIDEO CDs can hold six times the
audio information of conventional audio CDs.
There are two versions of VIDEO CDs.
• Version 1.1: You can play only moving
pictures and sounds.
• Version 2.0: You can play high-resolution still
pictures and enjoy PBC functions.
This system conforms to both versions.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1183
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
1347
1349
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1507
1508
1509
1511
1512
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali;
Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian;
Lettish
1345 Malagasy
1436
1463
1481
1482
1483
1489
1491
1495
1498
1501
1502
1503
1505
1506
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan)Oromo
Oriya
Punjabi
Polish
Pashto;
Pushto
Portuguese
Quechua
RhaetoRomance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
SerboCroatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Chinese
Zulu
Additional Information
Code Language
1703 Not specified
Parental Control Area Code List
Code Area
Code Area
Code Area
Code Area
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2248
2238
2254
2276
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2528
2184
Argentina
Australia
Austria
Belgium
Brazil
Canada
Chile
China
Denmark
Finland
France
Germany
India
Indonesia
Italy
Japan
Korea
Malaysia
Mexico
Netherlands
New Zealand
Norway
Pakistan
Philippines
Portugal
Russia
Singapore
Spain
Sweden
Switzerland
Thailand
United
Kingdom
95GB
Index to Parts and Controls
For more information, refer to the pages indicated in parentheses.
Front panel
A "/1 (on/standby) (30)
G VOLUME control (30)
B A (open/close) (30)
H MIC 2 jack (62)
C Disc operation (30)
D FUNCTION (30)
I AUDIO IN/MIC 1/A.CAL MIC jack (19, 28,
62)
E Front panel display (98)
J Disc tray (30)
F
96GB
(remote sensor) (8)
Rear panel
Screws*
SPEAKER
FRONT R
FRONT L
SUR R
SPEAKER
CENTER
COAXIAL
SUR L
AM
DMPORT
TV /
VIDEO
DIR-TC1
FM75
R AUDIO IN L
VIDEO
WOOFER
(DVD ONLY)
OUT
(DVD ONLY)
S VIDEO
Y
P B/C B
P R/C R
COMPONENT VIDEO OUT
(DVD ONLY)
MONITOR OUT
A SPEAKER jacks (14)
G COAXIAL FM 75Ω jack (14)
B DIR-TC1 slot for the WAHT-SD1 (28)
H COMPONENT VIDEO OUT jacks (24)
C TV/VIDEO (AUDIO IN R/L) jacks (28)
I HDMI OUT jack (24)
D DMPORT (DIGITAL MEDIA PORT) jack
(28, 67)
E MONITOR OUT (S VIDEO/VIDEO) jacks
(24)
F AM terminal (14)
*
CAUTION
Please do not remove the screws before
installing the WAHT-SD1.
Additional Information
continued
97GB
Front panel display
About the indications in the front panel display
A Lights up when the HDMI OUT jack is
correctly connected to HDCP (highbandwidth digital content protection)
compliant device with HDMI or DVI
(digital visual interface) input. (24)
B Lights up when the time information of
a title or chapter appears in the front
panel display. (DVD only) (46)
C Lights up when an NTSC disc is
loaded.
D Lights up when a station is received.
(Radio only) (58)
E Stereo/Monaural effect (Radio only)
(59)
F Lights up when the sleep timer is set.
(66)
G Lights up when the movie or music
mode is selected. (33)
H Playing status (DVD function only)
I Lights up when the karaoke mode is
on. (62)
98GB
J Current repeat mode (42)
K Lights up when the child lock function
is set to on. (68)
L Lights up when the system outputs
progressive signals (DVD function
only). (26)
M Indicates the selected [SPEAKER
FORMATION]. (72)
N Current surround format (Except for
JPEG)
O Lights up when the DYNAMIC BASS is
selected. (66)
P Displays system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, sound field, etc.
Guide to the Control Menu Display
DISPLAY
Use the Control Menu display to select a function and to view related information. Press
repeatedly to turn on or change the Control Menu display as follows:
DISPLAY
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For details
about each item, see the pages in parentheses.
Additional Information
, Control Menu display 1
m
Control Menu display 2 (appears for certain discs only)
m
Control Menu display off
Example: Control Menu display 1 when playing a DVD VIDEO.
continued
99GB
Currently playing title number1)
Currently playing chapter number2)
Total number of titles1)
Total number of chapters2)
Control Menu items
12 (27)
18 (34)
T
1:32:55
Selected item
Function name of
selected Control
Menu item
DVD VIDEO
Playback status
(N Playback,
X Pause,
x Stop, etc.)
Type of disc being
played3)
Playing time4)
OFF
OFF
DISC
TITLE
CHAPTER
Current setting
Options
REPEAT
ENTER
Quit:
DISPLAY
Operation message
1) Displays
the scene number for VIDEO CDs (PBC is on), track number for VIDEO CDs/CDs, album number for
DATA CDs/DATA DVDs. DivX video album number for DATA CDs/DATA DVDs.
2)
Displays the index number for VIDEO CDs, MP3 audio track number, or JPEG image file number for DATA CDs/
DATA DVDs. DivX video file number for DATA CDs/DATA DVDs.
3)
Displays Super VCD as “SVCD.” Displays “MP3” in the Control Menu display 1 or “JPEG” in the Control Menu
display 2 for DATA CDs/DATA DVDs.
4)
Displays the date for JPEG files.
To turn off the display
Press
DISPLAY.
List of Control Menu items
Item
Item Name, Function, Relevant Disc Type
[TITLE] (page 37)/[SCENE] (page 37)/[TRACK] (page 37)
Selects the title, scene, or track to be played.
[CHAPTER] (page 37)/[INDEX] (page 37)
Selects the chapter or index to be played.
[TRACK] (page 37)
Selects the track to be played.
[ORIGINAL/PLAY LIST] (page 45)
Selects the type of titles (DVD-RW/DVD-R) to be played, the [ORIGINAL] one, or an edited
[PLAY LIST].
[TIME/TEXT] (page 37)
Checks the elapsed time and the remaining playback time.
Input the time code for picture and music searching.
Displays the DVD/CD text or the MP3 track name.
100GB
[SPEAKER FORMATION] (pages 72, 74)
Sets the speaker formation./Adjust the level of each speaker automatically.
[PROGRAM] (page 39)
Selects the track to play in the order you want.
[SHUFFLE] (page 41)
Plays the track in random order.
[REPEAT] (page 42)
Plays the entire disc (all titles/all tracks/all albums) repeatedly or one title/chapter/track/album
repeatedly.
[A/V SYNC] (page 49)
Adjusts the delay between the picture and sound.
[PARENTAL CONTROL] (page 69)
Sets to prohibit playback on this system.
[SETUP] (page 76)
[QUICK] Setup (page 19)
Use Quick Setup to choose the desired language of the on-screen display, the aspect ratio of
the TV, speaker formation, and choose yes or no to start the Auto Calibration.
[CUSTOM] Setup
In addition to the Quick Setup setting, you can adjust various other settings.
[RESET]
Returns the settings in [SETUP] to the default setting.
[ALBUM] (page 37)
Additional Information
Selects the album to be played.
[FILE] (page 37)
Selects the JPEG image file or DivX video file* to be played.
*
[DATE] (page 47)
Displays the date the picture was taken by a digital camera.
*
[INTERVAL] (page 54)
Specifies the duration for which the slides are displayed on the TV screen.
*
[EFFECT] (page 54)
Selects the effects to be used for changing slides during a slide show.
*
[MODE (MP3, JPEG)] (page 53)
Selects the data type; MP3 audio track (AUDIO), JPEG image file (IMAGE) or both (AUTO)
to be played when playing a DATA CD/DATA DVD.
List of Control Menu Items for karaoke
Item
Item Name, Function, Relevant Disc Type
[KARAOKE MODE] (page 62)
Set karaoke mode to on and off.
[SCORE MODE] (page 62)
Calculates your vocal score by comparing your voice with the music source.
[VOCAL SELECT] (page 62)
Selects different kind of vocals recorded in the disc.
* These items are not displayed when playing a DATA CD/DATA DVD with DivX video file.
continued
101GB
Tip
• The Control Menu icon indicator lights up in green
when you select any item except [OFF]
t
([PROGRAM], [SHUFFLE], [REPEAT], [A/V SYNC], [KARAOKE MODE], and [VOCAL SELECT] only). The
[ORIGINAL/PLAY LIST] indicator lights up in green when you select [PLAY LIST] (default setting).
102GB
DVD Setup Display List
You can set the following items with the DVD Setup Display.
The order of the displayed items may be different from the actual display.
LANGUAGE SETUP
CUSTOM SETUP
OSD*
MENU*
AUDIO*
SUBTITLE*
SCREEN SETUP
TV TYPE
YCBCR/RGB (HDMI)
SCREEN SAVER
BACKGROUND
OFF
ON
PAUSE
MODE
TRACK
SELECTION
MULTI-DISC
RESUME
AUDIO DRC
AUTO
FRAME
OFF
AUTO
ON
OFF
OFF
STANDARD
MAX
OFF
ON
AUDIO
(HDMI)
DivX
SPEAKER SETUP
CONNECTION
FRONT
CENTER
DISTANCE
(FRONT)
SUBWOOFER
L
R
CENTER
YES
YES
NONE
YES
NONE
YES
1.0 m – 7.0 m
1.0 m – 7.0 m
0.0 m – 7.0 m
DISTANCE
(SURROUND)
L
R
0.0 m – 7.0 m
0.0 m – 7.0 m
LEVEL
(FRONT)
L
R
CENTER
SUBWOOFER
L
R
–6.0 dB – 0.0 dB
–6.0 dB – 0.0 dB
–6.0 dB – +6.0 dB
–6.0 dB – +6.0 dB
–6.0 dB – +6.0 dB
–6.0 dB – +6.0 dB
SURROUND
LEVEL
(SURROUND)
TEST TONE
Additional Information
4:3 OUTPUT
16:9
4:3 LETTER
BOX
4:3 PAN SCAN
YCBCR
RGB
ON
OFF
JACKET
PICTURE
GRAPHICS
BLUE
BLACK
FULL
NORMAL
HDMI
CONTROL
OFF
ON
* Select the language you want to use from the displayed language list.
103GB
System Menu List
You can set the following items with SYSTEM MENU on the remote.
System menu
MEMORY1)
FM MODE2)
NAME IN1)
SLEEP
DIMMER
MEMORY 1-20 (FM), MEMORY 1-10 (AM)
STEREO
MONO
SLEEP OFF, SLEEP 90M-1M
DIMMER OFF
DIMMER ON
DEMO
DEMO ON
DEMO OFF
ATTENUATE3)
ATT ON
ATT OFF
REV OFF
REV ON
OFF
ON
SL SR REV4)
CHILD LOCK
1)Appears
during “TUNER FM” or “TUNER AM” only.
2)Appears
during “TUNER FM” only.
3)
“ATTENUATE” may not appear, depending on the selected function.
4)
Appears when the wireless kit WAHT-SD1 is installed.
104GB
Index
Numerics
16:9 78
4:3 LETTER BOX 78
4:3 OUTPUT 79
4:3 PAN SCAN 78
5.1 Channel Surround 44
A
A/V SYNC 49
ALBUM 37
Album 92
ANGLE 48
ATTENUATE 32
AUDIO 78
AUDIO (HDMI) 80
AUDIO DRC 80
Auto Calibration 74, 92
B
BACKGROUND 79
Batteries 8
C
CHAPTER 37
Chapter 92
Child Lock 68
COLD RESET 84
COMPONENT VIDEO OUT
26
Continuous play 30
Control Menu Display 99
Controlling the TV 61
CUSTOM 76
CUSTOM PARENTAL
CONTROL 69
CUSTOM SETUP 80
D
D. C. A. C. 74, 92
DATA CD 51, 55
DATA DVD 51, 55
DEMO 22
Demonstration 22
Digital Cinema Auto
Calibration 74, 92
DIGITAL MEDIA PORT 67
DIMMER 67
DISPLAY 60
DivX® 55, 81, 92
Dolby Digital 43, 92
Dolby Pro Logic II 92
Dolby Surround Pro Logic 93
DTS 43, 93
DVD 93
DVD+RW 93
DVD’s menu 43
DVD-RW 45, 93
DVI 25
DYNAMIC BASS 66
E
EFFECT 54
F
Fast forward 36
Fast reverse 36
FILE 37
File 93
Film based software 93
FM MODE 59
Freeze Frame 36
Front panel 96
Front panel display 46, 98
L
Language Code List 95
LANGUAGE SETUP 78
Listening
a particular point on a disc 36
other components 31
TV sound 32
M
MENU 78
Microphones 62
MODE (MP3, JPEG) 53
MOVIE/MUSIC 33
MP3 49, 51
MPEG audio 94
Multi Session CD 6
Multi-angle function 48, 94
MULTI-DISC RESUME 80
Multilingual function 94
MUTING 31
N
H
Naming preset stations 59
Handling discs 86
HDMI
YCBCR/RGB (HDMI) 78
HDMI (high-definition
multimedia interface) 25, 93
HDMI CONTROL 80
O
I
ORIGINAL 45
OSD 78
Other component connection
28
P
JPEG 49, 51
PARENTAL CONTROL 70
Parental Control 94
PAUSE MODE 80
PBC Playback 57
PCM (Pulse Code Modulation)
94
PICTURE NAVI 38, 52
PLAY LIST 45
Playback Control (PBC) 94
Program Play 39
PROGRESSIVE 27
Progressive format 26
K
Q
Karaoke 62
ECHO 63
Karaoke Pon 64
Key Control 64
Score Mode 65
Vocal Select 64
Quick Setup 19
INDEX 37
Installing the speakers on a wall
23
Instant Advance 30
Instant Replay 30
INTERLACE 27
Interlace format 93
INTERVAL 54
J
continued
105GB
R
Radio 59
Radio Stations 58
Rear Panel 97
Region Code 6, 94
Remote 8, 61
Repeat Play 42
RESET 77
Resume Play 38
S
S VIDEO 25
Scan 36
SCENE 37
Scene 94
SCREEN SAVER 79
SCREEN SETUP 78
Searching 36
Selecting 33
SETUP 76
Setup Display 76, 103
Shuffle Play 41
SLEEP 66
Slide Show 53
Slow-motion Play 36
Sound Field 34
SPEAKER FORMATION 72
SPEAKER SETUP 81
CONNECTION 81
DISTANCE 82
LEVEL 82, 83
SUBTITLE 48, 78
SYSTEM MENU 22, 32, 59,
66, 67, 68
System menu list 104
T
TEST TONE 83
THEATRE SYNC 61
TIME/TEXT 37
TITLE 37
Title 94
TRACK 37
Track 94
TRACK SELECTION 80
Troubleshooting 86
TV connection 24
TV TYPE 78
U
Unpacking 92
Usable discs 5
V
VIDEO CD 94
106GB
Remote control
ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
A–O
P–Z
ANGLE 5 (48)
AUDIO 4 (43)
CLEAR ef (37, 61, 77)
D.TUNING wf (59)
DISPLAY ej (46, 60)
DVD MENU wh (43, 55, 61)
DVD TOP MENU qf (43)
DYNAMIC BASS wd (66)
ECHO qk (63)
ENTER wg (61)
FUNCTION ws (26, 30, 31, 38,
58, 72)
KARAOKE PON 2 (64)
KEYCON #/b wa (64)
MIC VOL +/– eh (63)
MOVIE/MUSIC qj (33)
MUTING 7 (30)
Number buttons* qg (37, 59, 61,
69)
PICTURE NAVI 6 (38, 61)
PRESET +/– wk es (59)
SCORE eg (65)
SOUND FIELD qh (34)
SUBTITLE wf (48)
SYSTEM MENU wg (22, 32, 61,
67, 104)
THEATRE SYNC w; (62)
TUNING +/– 0 qs (58)
TV e; (61)
TV CH +/– wk es (61)
TV INPUT ej (61)
TV VOL +/–* 8 (61)
VIDEO FORMAT 3 (26)
VOLUME +/–* 8 (30, 59, 83)
[/1 (on/standby) 1 (19, 22, 30,
38, 59)
TV [/1 (on/standby) 1 (61)
C/X/x/c/
qd (19, 22, 32, 37,
58, 69)
REPLAY/
ADVANCE 9 (30)
./> es wk (30)
m/M qs 0 (36)
/
SLOW qs 0 (36)
H (play)* ea (30, 38, 71)
STEP 9 (36)
x (stop) wl (30, 38, 69)
X (pause) qa (30)
Z (open/close) ql (30)
DISPLAY wj (20, 37, 69, 99)
O RETURN ed (38)
-/-- ef (61)
* The H, number 5, and
VOLUME + (TV VOL+)
buttons have tactile dots. Use
the tactile dots as references
when operating the system.
Sony Corporation Printed in China