Sony KDL-22CX32D User's Manual

4-270-482-11(1)
LCD
Digital Colour TV
Operating Instructions
KDL-22CX32D
NOTICE FOR
CUSTOMERS IN
THE UNITED
KINGDOM
A moulded plug complying with BS1363
is fitted to this equipment for your safety
and convenience.
Should the fuse in the plug supplied need
to be replaced with the same rating of fuse
approved by ASTA or BSI to BS 1362 (i.e.,
marked with
or ) must be used.
When an alternative type of plug is used it
should be fitted with the same rating of
fuse, otherwise the circuit should be
protected by a 10 AMP FUSE at the
distribution board.
If the plug supplied with this equipment
has a detachable fuse cover, be sure to
attach the fuse cover after you change the
fuse. Never use the plug without the fuse
cover. If you should lose the fuse cover,
please contact your nearest Sony service
station.
• Your cable provider may charge a fee for
their services, or require you to agree to
its terms and conditions of business.
• This TV set complies with DVB-T and
DVB-C specifications, but compatibility
with future DVB-T digital terrestrial and
DVB-C digital cable broadcasts are not
guaranteed.
• Some Digital TV functions may not be
available in some countries/areas and
DVB-C cable may not operate correctly
with some providers.
The manufacturer of this product is
Sony Corporation, 1-7-1 Konan
Minato-ku Tokyo, 108-0075 Japan.
The Authorized Representative for
EMC and product safety is Sony
Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart,
Germany. For any service or
guarantee matters please refer to the
addresses given in separate service or
guarantee documents.
~
• The illustration used in this
manual are of the KDL-22CX32D
unless otherwise state.
Trademark information
•
•
FUSE
•
•
FUSE
How to replace the fuse
Open the fuse compartment with a blade
screwdriver, and replace the fuse.
Please refer to the illustration that actually
equipped with the product.
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this
manual thoroughly and retain it for future
reference.
Notice for Digital TV
function
• Any functions related to Digital TV
(
) will only work in countries or
areas where DVB-T (MPEG-2 and
H.264/MPEG-4 AVC) digital terrestrial
signals are broadcast or where you have
access to a compatible DVB-C (MPEG2 and H.264/MPEG-4 AVC) cable
service. Please confirm with your local
dealer if you can receive a DVB-T signal
where you live or ask your cable
provider if their DVB-C cable service is
suitable for integrated operation with this
TV.
2 GB
•
•
is a registered trademark of the
DVB Project.
HDMI, the HDMI Logo, and HighDefinition Multimedia Interface are
trademarks or registered trademarks of
HDMI Licensing LLC in the United
States and other countries.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.
DivX®, DivX Certified® and associated
logos are registered trademarks of DivX,
Inc. and are used under license.
ABOUT DIVX VIDEO: DivX® is a
digital video format created by DivX,
Inc. This is an official DivX Certified
device that plays DivX video. Visit
www.divx.com for more information
and software tools to convert your files
into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND:
This DivX Certified® device must be
registered in order to play DivX Videoon-Demand (VOD) content. To generate
the registration code, locate the DivX
VOD section in the device setup menu.
Go to vod.divx.com with this code to
complete the registration process and
learn more about DivX VOD.
“BRAVIA” and
are
trademarks of Sony Corporation.
is a trademark of DVD Format/
Logo Licensing Corporation.
• “DVD VIDEO” and “CD” logos are
trademarks.
• This product incorporates copyright
protection technology that is protected
by method claims of certain U.S. patents,
other intellectual property rights owned
by Macrovision Corporation, and other
right owners. Use of this copyright
protection technology must be
authorized by Macrovision Corporation,
and is intended for home and other
limited viewing uses only unless
otherwise authorized by Macrovision
Corporation. Reverse engineering or
disassembly is prohibited.
Location of the
identification label
Labels for Model No., Production Date
(month/year) and Power Supply rating (in
accordance with applicable safety
regulation) are located on the rear of the
TV or package.
Table of Contents
Start-up Guide
4
Safety Information.............................................................................................................8
Precautions........................................................................................................................9
Safety information about built-in DVD player...............................................................10
Precautions about built-in DVD player..........................................................................10
Overview of the remote ..................................................................................................11
Overview of the TV buttons and indicators ..................................................................13
Watching TV
Watching TV ....................................................................................................................14
Using the Digital Electronic Programme Guide (EPG)
.......................................16
Using the Digital Favourite list
.............................................................................17
Playing a DVD..................................................................................................................18
Enjoying Karaoke............................................................................................................21
Using Optional Equipment
Connecting optional equipment ....................................................................................22
Viewing pictures from connected equipment ..............................................................23
Playing Back Photo/Music/Video via USB ....................................................................24
Using BRAVIA Sync with Control for HDMI ..................................................................27
Using MENU Functions
Navigating through TV Menu .........................................................................................28
Settings ............................................................................................................................29
Additional Information
Installing the Accessories (Wall-Mount Bracket) .........................................................40
Specifications..................................................................................................................42
Troubleshooting..............................................................................................................44
: for digital channels only
• Before operating the TV, please read “Safety Information” (page 8). Retain this manual for future reference.
• Instructions about “Installing Wall Mount Bracket” are included within this TV’s instructions manual.
3 GB
Start-up Guide
1: Checking the
accessories
2: Attaching the stand
Table-Top Stand (1)
Screws for stand (7)
Remote RM-ED046 (1)
Size AA batteries (2)
1
Refer to the supplied Table-Top Stand
leaflet for proper attachment for some TV
models.
2
Place the TV set on the stand. Take care
not to interfere with cables.
3
Fix the TV to the stand according to the
arrow marks
that guide the screw
holes using the supplied screws.
Follow the assembling steps required to place on a
TV stand.
To insert batteries into the remote
Push to
open
~
• Observe the correct polarity when inserting batteries.
• Do not use different types of batteries together or mix
old and new batteries.
• Dispose of batteries in an environmentally friendly way.
Certain regions may regulate the disposal of batteries.
Please consult your local authority.
• Handle the remote with care. Do not drop or step on it,
or spill liquid of any kind onto it.
• Do not place the remote in a location near a heat source,
a place subject to direct sunlight, or a damp room.
~
• If using an electric screwdriver, set the tightening torque
at approximately 1.5 N·m (15 kgf·cm).
4 GB
Connecting an aerial/cable/VCR/DVD recorder with
HDMI
Connecting an aerial/cable only
Terrestrial signal
or cable
Coaxial cable
Coaxial
cable
Terrestrial signal
or cable
HDMI
cable
Coaxial cable
Connecting an aerial/cable/VCR/DVD recorder with
SCART
VCR/DVD recorder
Coaxial cable
4: Preventing the TV
from toppling over
Terrestrial
signal or
cable
Scart lead
Coaxial cable
2
3
VCR/DVD recorder
1
1
Install a wood screw (4 mm in diameter,
not supplied) in the TV stand.
Continued
5 GB
Start-up Guide
3: Connecting an
aerial/cable/VCR/DVD
recorder
2
Install a machine screw (M4 × 16, not
supplied) into the screw hole of the TV.
3
Tie the wood screw and the machine
screw with a strong cord (not supplied).
3
Press F/f/G/g to select the language
displayed on the menu screens, then
press .
Language
Select language.
z
• An optional Sony support belt kit is used to secure the TV.
Contact your nearest Sony Service Centre to purchase a
kit. Have your TV model name ready for reference.
5: Selecting the
language, country/region
and location
Select
4
Next
Follow the on-screen instructions to
select the country/region in which you will
operate the TV.
If the country/region which you want to use on
the TV does not appear in the list, select “-”
instead of a country/region.
5
Follow the on-screen instructions to set
the PIN code.
z
• Any PIN code can be used, except 0000. To change
the PIN code later, see page 36.
6
Follow the on-screen instructions to
select the location type in which you will
operate the TV.
This option selects the initial picture mode
appropriate for the typical lighting condition in
these environments.
In Shop mode, some settings will be periodically
reset for Shop usage.
6: Auto-tuning the TV
3,4,5,6
1
Press G/g to select “Start”, then press
.
Auto Tuning
1
Connect the TV to your mains socket
(220-240V AC, 50Hz).
2
Press 1 on the side of the TV.
Do you want to start Auto Tuning?
Start
When you turn on the TV for the first time, the
Language menu appears on the screen.
Skip
~
• When you turn on the TV, the power indicator lights
up in green.
2
Press F/f to select “Antenna” or “Cable”,
then press .
If you select “Cable”, the screen for selecting the
scan type appears. See “To tune the TV for
Cable connection” (page 7). The TV then starts
searching for all available digital channels,
followed by all available analogue channels.
This may take some time, so do not press any
buttons on the TV or remote while proceeding.
6 GB
3
Programme Sorting (Only in analogue
mode): Changes the order in which the
analogue channels are stored on the TV.
1 Press F/f to select the channel you want to
move to a new position, then press g.
2 Press F/f to select the new position for your
channel, then press .
If you do not change the order in which the
analogue channels are stored on the TV, press
HOME to go to next step.
Detaching the TableTop Stand from the TV
~
• Do not remove the Table-Top Stand for any reason other
than to wall-mount the TV.
~
• This step will not appear if any analogue channel is
found.
The message “Set-up complete” will appear on
the screen. Press .
The TV has now tuned in all the available
channels.
z
• USB System Update
You can update the TV system using USB memory.
Obtain information from the website below.
http://support.sony-europe.com/TV/
Table-Top
Stand
z
• Be sure the TV is on the vertical position before
switching on. TV set must not be powered on with LCD
panel face down to avoid uneven picture uniformity.
To tune the TV for Cable connection
1
Press
and F/f to select “Quick Scan”
or “Full Scan”, then press .
“Quick Scan” : channels are tuned according to
the cable operator information within the
broadcast signal.
Recommended setting for “Frequency” and
“Network ID” is “Auto”.
This option is recommended for fast tuning
when supported by your cable operator.
If the “Quick Scan” does not tune, please use the
“Full Scan” method below.
“Full Scan” : All available channels are tuned
and stored. This procedure may take some time.
This option is recommended when “Quick Scan”
is not supported by your cable provider.
2
Press f to select “Start”.
The TV starts searching for channels. Do not
press any buttons on the TV or remote.
~
• Some cable providers do not support “Quick Scan”. If no
channels are detected using “Quick Scan”, perform “Full
Scan”.
7 GB
Start-up Guide
If a message appears for you to confirm the
aerial connection
No digital or analogue channels were found.
Check all the aerial/cable connections and press
to start auto-tuning again.
Safety
Information
Installation/Set-up
Install and use the TV set in accordance
with the instructions below in order to
avoid any risk of fire, electrical shock or
damage and/or injuries.
Installation
• The TV set should be installed near an
easily accessible mains socket.
• Place the TV set on a stable, level
surface.
• Only qualified service personnel should
carry out wall installations.
• For safety reasons, it is strongly
recommended that you use Sony
accessories, including:
– Wall-mount bracket
SU-WL100
• Be sure to use the screws supplied with
the Wall-mount bracket when attaching
the mounting hooks to the TV set. The
supplied screws are designed so that they
are 6.5 mm to 10 mm in length when
measured from the attaching surface of
the mounting hook. The diameter and
length of the screws differ depending on
the Wall-mount bracket model. Use of
screws other than those supplied may
result in internal damage to the TV set or
cause it to fall, etc.
6.5 ~ 10mm
Screw (supplied with the
Wall-mount bracket)
Mounting Hook
Hook attachment on rear
of TV set
Transporting
• Before transporting the TV set,
disconnect all cables.
• Two or three people are needed to
transport a large TV set.
• When transporting the TV set by hand,
hold it as shown in the illustration. Do
not put stress on the LCD panel and the
frame around the screen.
• When transporting the TV set, do not
subject it to jolts or excessive vibration.
• When transporting the TV set for repairs
or when moving, pack it using the
original carton and packing material.
–
Ventilation
–
• Never cover the ventilation holes or
insert anything in the cabinet.
• Leave space around the TV set as shown
below.
• It is strongly recommended that you use
a Sony wall-mount bracket in order to
provide adequate air-circulation.
Installed on the wall
30 cm
10 cm
20 cm
10 cm
Leave at least this space around
the set.
Installed with stand
20 cm
• When lifting or moving the TV set, hold
it firmly from the bottom.
6 cm
Leave at least this space around
the set.
• To ensure proper ventilation and prevent
the collection of dirt or dust:
– Do not lay the TV set flat, install
upside down, backwards, or
sideways.
– Do not place the TV set on a shelf,
rug, bed or in a closet.
– Do not cover the TV set with a cloth,
such as curtains, or items such as
newspapers, etc.
– Do not install the TV set as shown
below.
Air circulation is blocked.
Wall
Wall
Mains lead
Handle the mains lead and socket as
follows in order to avoid any risk of fire,
electrical shock or damage and/or injuries:
–
–
–
–
8 GB
Notes
• Do not use the supplied mains lead on
any other equipment.
• Do not pinch, bend, or twist the mains
lead excessively. The core conductors
may be exposed or broken.
• Do not modify the mains lead.
• Do not put anything heavy on the mains
lead.
• Do not pull on the mains lead itself when
disconnecting the mains lead.
• Do not connect too many appliances to
the same mains socket.
• Do not use a poor fitting mains socket.
Prohibited Usage
30 cm
10 cm
–
care not to catch your feet on the
cables.
Disconnect the mains lead from the
mains socket before working on or
moving the TV set.
Keep the mains lead away from heat
sources.
Unplug the mains plug and clean it
regularly. If the plug is covered with
dust and it picks up moisture, its
insulation may deteriorate, which
could result in a fire.
Use only mains leads supplied by
Sony, not other suppliers.
Insert the plug fully into the mains
socket.
Operate the TV set on a 220–240 V AC
supply only.
When wiring cables, be sure to unplug
the mains lead for your safety and take
Do not install/use the TV set in locations,
environments or situations such as those
listed below, or the TV set may
malfunction and cause a fire, electrical
shock, damage and/or injuries.
Location:
• Outdoors (in direct sunlight), at the
seashore, on a ship or other vessel, inside
a vehicle, in medical institutions,
unstable locations, near water, rain,
moisture or smoke.
• If the TV is placed in the changing room
of a public bath or hot spring, the TV
may be damaged by airborne sulfur, etc.
Environment:
• Places that are hot, humid, or excessively
dusty; where insects may enter; where it
might be exposed to mechanical
vibration, near flammable objects
(candles, etc). The TV set shall not be
exposed to dripping or splashing and no
objects filled with liquids, such as vases,
shall be placed on the TV.
• Do not place the TV in a humid or dusty
space, or in a room with oily smoke or
steam (near cooking tables or
humidifiers). Fire, electric shock, or
warping may result.
Situation:
• Do not use when your hands are wet,
with the cabinet removed, or with
attachments not recommended by the
manufacturer. Disconnect the TV set
from mains socket and aerial during
lightning storms.
• Do not install the TV so that it sticks out
into an open space. Injury or damage
from a person or object bumping into the
TV may result.
Broken pieces:
• Do not throw anything at the TV set. The
screen glass may break by the impact and
cause serious injury.
• If the surface of the TV set cracks, do not
touch it until you have unplugged the
mains lead. Otherwise electric shock
may result.
• Do not subject the LCD screen to any
strong impact or shock. The screen glass
may crack or shatter and cause injury.
•
•
•
When not in use
• If you will not be using the TV set for
several days, the TV set should be
disconnected from the mains for
environmental and safety reasons.
• As the TV set is not disconnected from
the mains when the TV set is just turned
off, pull the plug from the mains to
disconnect the TV set completely.
• However, some TV sets may have
features that require the TV set to be left
in standby to work correctly.
For children
• Do not allow children to climb on the TV
set.
• Keep small accessories out of the reach
of children, so that they are not
mistakenly swallowed.
If the following problems
occur...
Turn off the TV set and unplug the mains
lead immediately if any of the following
problems occur.
Ask your dealer or Sony service centre to
have it checked by qualified service
personnel.
When:
–
–
–
–
Mains lead is damaged.
Poor fitting of mains socket.
TV set is damaged by being dropped,
hit or having something thrown at it.
Any liquid or solid object falls through
openings in the cabinet.
Warning
To prevent the spread of fire, keep candles
or other open flames away from this
product at all time.
•
•
constantly on the LCD screen. This is a
structural property of the LCD screen
and is not a malfunction.
Do not push or scratch the front filter, or
place objects on top of this TV set. The
image may be uneven or the LCD screen
may be damaged.
If this TV set is used in a cold place, a
smear may occur in the picture or the
picture may become dark. This does not
indicate a failure. These phenomena
disappear as the temperature rises.
Ghosting may occur when still pictures
are displayed continuously. It may
disappear after a few moments.
The screen and cabinet get warm when
this TV set is in use. This is not a
malfunction.
The LCD screen contains a small amount
of liquid crystal. Some fluorescent tubes
used in this TV set also contain mercury.
Follow your local ordinances and
regulations for disposal.
Handling and cleaning the
screen surface/cabinet of
the TV set
Be sure to unplug the mains lead connected
to the TV set from mains socket before
cleaning.
To avoid material degradation or screen
coating degradation, observe the following
precautions.
• To remove dust from the screen surface/
cabinet, wipe gently with a soft cloth. If
dust is persistent, wipe with a soft cloth
slightly moistened with a diluted mild
detergent solution.
• Do not spray water or detergent directly
on the TV set. It may drip to the bottom
of the screen or exterior parts, and may
cause a malfunction.
• Never use any type of abrasive pad,
alkaline/acid cleaner, scouring powder,
or volatile solvent, such as alcohol,
benzene, thinner or insecticide. Using
such materials or maintaining prolonged
contact with rubber or vinyl materials
may result in damage to the screen
surface and cabinet material.
• Periodic vacuuming of the ventilation
openings is recommended to ensure to
proper ventilation.
• When adjusting the angle of the TV set,
move it slowly so as to prevent the TV
set from moving or slipping off from its
table stand.
Optional Equipment
Precautions
• Keep optional components or any
equipment emitting electromagnetic
radiation away from the TV set.
Otherwise picture distortion and/or noisy
sound may occur.
• This equipment has been tested and
found to comply with the limits set out in
the EMC Directive using a connection
signal cable shorter than 3 meters.
Viewing the TV
Batteries
• View the TV in moderate light, as
viewing the TV in poor light or during
long period of time, strains your eyes.
• When using headphones, adjust the
volume so as to avoid excessive levels,
as hearing damage may result.
• Observe the correct polarity when
inserting batteries.
• Do not use different types of batteries
together or mix old and new batteries.
• Dispose of batteries in an
environmentally friendly way. Certain
regions may regulate the disposal of
batteries. Please consult your local
authority.
• Handle the remote with care. Do not
drop or step on it, or spill liquid of any
kind onto it.
LCD Screen
• Although the LCD screen is made with
high-precision technology and 99.99%
or more of the pixels are effective, black
dots may appear or bright points of light
(red, blue, or green) may appear
• Do not place the remote in a location
near a heat source, a place subject to
direct sunlight, or a damp room.
Disposal of the TV set
Disposal of Old
Electrical &
Electronic
Equipment
(Applicable in
the European
Union and other European
countries with separate
collection systems)
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the
environment and human health, which
could otherwise be caused by
inappropriate waste handling of this
product. The recycling of materials will
help to conserve natural resources. For
more detailed information about recycling
of this product, please contact your local
Civic Office, your household waste
disposal service or the shop where you
purchased the product.
Disposal of
waste batteries
(applicable in the
European Union
and other
European
countries with separate
collection systems)
This symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not be
treated as household waste. On certain
batteries this symbol might be used in
combination with a chemical symbol. The
chemical symbols for mercury (Hg) or lead
(Pb) are added if the battery contains more
than 0.0005% mercury or 0.004% lead. By
ensuring these batteries are disposed of
correctly, you will help prevent potentially
negative consequences for the
environment and human health which
could otherwise be caused by
inappropriate waste handling of the
battery. The recycling of the materials will
help to conserve natural resources. In case
of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery,
this battery should be replaced by qualified
service staff only. To ensure that the
battery will be treated properly, hand over
the product at end-of-life to the applicable
collection point for the recycling of
electrical and electronic equipment. For all
Continued
9 GB
other batteries, please view the section on
how to remove the battery from the product
safely. Hand the battery over to the
applicable collection point for the
recycling of waste batteries. For more
detailed information about recycling of
this product or battery, please contact your
local Civic Office, your household waste
disposal service or the shop where you
purchased the product.
Safety
information about
built-in DVD
player
• The use of optical instruments with this
product will increase eye hazard. As the
laser beam used in this built-in DVD
player is harmful to eyes, do not attempt
to disassemble the cabinet. Refer
servicing to qualified personnel only.
This appliance is classified as a CLASS 1
LASER product.
• To keep the disc clean, handle the disc
by its edge. Do not touch the surface.
Dust, fingerprints, or scratches on the
disc may cause it to malfunction.
• If you have printed the disc’s label, dry
the label before playing.
• If the TV is brought directly from a cold
to a warm location, or is placed in a very
damp room, or is placed in a room in
which heating has just been turned on,
moisture may condense on the surface
or inside the TV. Should this occur, turn
off the TV and leave the TV off until the
moisture evaporates, and then the TV
can be used. If a disc is inserted in the
built-in DVD player, eject and take out
the disc and turn off the TV. Using the
TV with moisture in or on it may cause
the TV to show poor picture and/or poor
colour or may cause a malfunction.
• Do not force a disc into the disc slot.
When there is already a disc inside the
built-in DVD player, trying to insert
another disc may cause malfunction.
• Sound may jump or picture distortion
may occur if a lens is dirty with dust.
For repair, contact the shop from which
the product was purchased or a
customer information service centre.
• Do not insert an unsupported disc or
foreign object in the built-in DVD
player, as a malfunction may result.
Precautions
about built-in
DVD player
• Do not use the following discs.
– A lens cleaning disc.
– A disc that has a nonstandard shape
(e.g., card, heart).
– A disc with a label or sticker on it.
– A disc that has cellophane tape or
sticker adhesive on it.
• Do not resurface the playing side of a
disc to remove surface scratches.
• When ejecting a disc from the built-in
DVD player by pressing Z on the TV,
be sure to take out the disc from the disc
slot. Do not leave the disc in the disc
slot.
• Eject and take out the disc from the disc
slot and turn off the TV when not using
the TV.
• Do not expose the disc to direct sunlight
or heat sources such as hot air ducts, or
leave it in a car parked in direct sunlight
as the temperature may rise
considerably inside the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth.
Wipe the disc from the centre out.
• Do not use solvents such as benzine,
thinner, commercially available disc/
lens cleaners, or anti-static spray
intended for vinyl LPs.
10 GB
• The TV has a region code located on the
rear of the unit.
• Do not use cleaning discs or disc/lens
cleaners (including wet or spray types).
These may cause the apparatus to
malfunction.
• When ejecting a disc, the disc may hit
objects and cause damage or injury.
Keep an open space around the disc
slot.
• Take out any discs from the built-in
DVD player when you move the TV. If
you don’t, the disc may be damaged.
Eject and take out the disc before
moving the TV.
• Do not pull out the AC power cord
(mains lead) while the built-in DVD
player is playing.
• Be sure small children do not put hands
into the disc slot. It may cause injury.
Overview of the remote
1 "/1 – TV standby
Turns the TV on and off from standby mode.
2 SYNC MENU
Displays the menu of connected HDMI equipment. While viewing
other input screens or TV programmes, “HDMI Device Selection” is
displayed when the button is pressed.
~
• “Control for HDMI” (BRAVIA Sync) is only available with the
connected Sony equipment that has the BRAVIA Sync or BRAVIA
Theatre Sync logo or is compatible with Control for HDMI.
3 AUDIO
• Press to change the dual sound mode (page 31).
• In DVD mode: Switches between the original and dubbing
languages* while playing.
4 SCENE – Scene Select mode (page 15)
5
/
– Info/Text reveal
• In digital mode: Displays brief details of the programme currently
being watched.
• In analogue mode: Displays information such as current channel
number and screen format.
• In DVD mode: Displays information on a title, chapter and playing
time.
• In Text mode (page 15): Reveals hidden information (e.g. answers to
a quiz).
6
F/f/G/g/
7 OPTIONS
Press to display a list that contains shortcuts to some setting menus. The
listed options vary depending on the current input and content.
8 HOME (page 28)
9 Coloured buttons (page 15, 17)
0 Number buttons
• In TV mode: Selects channels. For channel numbers 10 and above,
press the second and third digit in quick succession.
• In DVD mode: Number buttons for various data. Selects a chapter or
title.
• In Text mode: Enters the three digit page number to select the page.
qa
– Subtitle setting
• Press to change the subtitle language (page 35) (in digital mode
only).
• In DVD mode: Changes and displays the subtitles* of DVD while
playing (page 19).
* Depends on the DVD in use.
Continued
11 GB
qs PROG/CH +/–/
/
• In TV mode: Selects the next (+) or previous (-) channel.
• In Text mode (page 15): Selects the next ( ) or previous (
qd
) page.
– Previous channel
Press to return to the channel that was last viewed (for more than five
seconds).
qf % – Mute the sound
qg 2 +/– – Volume
qh / – Text (page 15)
qj RETURN /
Returns to the previous screen of any displayed menu.
qk GUIDE /
(page 16)
ql
– EPG (Digital Electronic Programme Guide)
– Screen mode (page 15)
w; DIGITAL – Digital mode (page 14)
ANALOG – Analogue mode (page 14)
wa BRAVIA Sync (page 27)
m/N/X/M/./x/>: You can operate the BRAVIA Synccompatible equipment that is connected to the TV.
In DVD mode, you can operate it as follows.
N: Starts playback.
X: Freezes a scene (DVD or video data). Pause audio.
x: Stops (all operations).
m: Changes the speed of reverse picture search mode during
playback.
M: Changes the speed of forward picture search mode during
playback.
.: Selects the previous title or chapter during playback.
>: Selects the next title or chapter during playback.
ws
/
– (Input select)
• In TV mode: Press to display a list of inputs.
z
• The number 5, N, PROG/CH + and AUDIO buttons have tactile dots. Use
the tactile dots as references when operating the TV.
12 GB
Overview of the TV buttons and indicators
1 Z – Eject
Ejects the disc.
2 N – Play
Starts disc playback.
3 x – Stop
Stops disc playback.
4 1 – Power
Turns the TV on or off.
~
• To disconnect the TV completely, pull the plug
from the mains.
• When you turn on the TV, the power indicator
lights in green.
5 CH +/–/
/
• In TV mode: Selects the next (+) or previous (-)
channel.
• In TV menu: Moves through the options up ( )
or down ( ).
6 2 +/–/
/
• In TV mode: Increases (+) or decreases (-) the
volume.
• In TV menu: Moves through the options right
( ) or left ( ).
7
/
– Input select / OK
• In TV mode: Selects the input source from
equipment connected to the TV sockets
(page 23).
• In TV menu: Selects the menu or option, and
confirms the setting.
8 HOME (page 28)
9 Light sensor
Do not put anything over the sensor, doing so may
affect its function (page 39).
Remote control sensor
• Receives IR signals from the remote.
• Do not put anything over the sensor, as its
function may be affected.
0
– Picture Off / Sleep Timer indicator
• Lights up in green when the picture is switched
off (page 39).
• Lights up in orange when the sleep timer is set
(page 37).
qa 1 – Standby indicator
Lights up in red when the TV is in standby mode.
qs " – Power indicator
Lights up in green when the TV is turned on.
~
• Make sure that the TV is completely turned off before
unplugging the mains lead. Unplugging the mains lead
while the TV is turned on may cause the indicator to
remain lit or may cause the TV to malfunction.
13 GB
Watching TV
1
Watching TV
Press 1 on the side of the TV to turn on
the TV.
When the TV is in standby mode (the 1
(standby) indicator on the TV front panel is red),
press "/1 on the remote to turn on the TV.
2
Press DIGITAL/ANALOG to switch
between digital and analogue modes.
The channels available vary depending on the
mode.
3
Press the number buttons or PROG/CH
+/– to select a TV channel.
To select channel numbers 10 and above using
the number buttons, press the second and third
digits in quick succession.
To select a digital channel using the Digital
Electronic Programme Guide (EPG), see
page 16.
In digital mode
An information banner appears briefly. The
following icons may be indicated on the banner.
2
: Radio service
: Scrambled/Subscription service
: Multiple audio languages available
: Subtitles available
: Subtitles available for the hearing impaired
: Recommended minimum age for current
programme (from 4 to 18 years)
: Parental Lock
: Digital Programme Lock
3
3
14 GB
Additional operations
To
Do this
Adjust the volume
Press 2 + (increase)/
- (decrease).
Access the
Programme index
table (in analogue
mode only)
Press . To select an analogue
channel, press F/f, then press
.
To access Text
14:9*
Press /. Each time you press /, the display changes
cyclically as follows:
Text t Text over the TV picture (mix mode) t No
Text (exit the Text service)
To select a page, press the number buttons or / .
To reveal hidden information, press .
Displays 14:9 broadcasts
in the correct proportions.
As a result, black border
areas are visible on the
screen.
Full
Stretches a 4:3 picture
horizontally, to fill a 16:9
screen.
Zoom*
Scene Select mode
Displays cinemascopic
(letter box format)
broadcasts in the correct
proportions.
When you select the desired scene option, the
optimum sound quality and picture quality for the
selected scene are automatically set.
1
2
Press SCENE on the remote.
Captions*
Press F/f to select the mode, then press
.
“Auto”: Delivers optimum picture and sound
quality which is automatically set according to
input source. There may not be any effect
depending on the connected equipments.
“General”: Current user settings.
“Photo”: Delivers picture that reproduces the
texture and colour of a printed photo.
“Music”: Delivers dynamic and clear sound
effects like at a concert.
“Cinema”: Delivers theatre-like picture and
dynamic sound.
“Game”: Delivers the best picture and sound
quality for fullest game playing enjoyment.
“Graphics”: Delivers clearer detailed pictures
to reduce fatigue for prolonged viewing.
“Sports”: Delivers realistic picture with
surround sound like in a stadium.
Displays cinemascopic
(letter box format)
broadcasts with subtitles
on the screen.
* Parts of the top and bottom of the picture may be cut off.
~
• Depending on the signal, some screen formats may not
be selectable.
• Some characters and/or letters at the top and the bottom
of the picture may not be visible in “Wide Zoom”.
z
• You can adjust the vertical position of the picture when
selecting “Zoom”, “14:9” or “Captions”. Press F/f to
move up or down (e.g. to read subtitles).
~
• Except for “Auto”, “General” and “Music”, if any scene
mode is selected, picture mode selection in the picture
menu is not possible - release scene selection first.
To change the screen format manually to
suit the broadcast
Press
repeatedly to select the desired screen format.
Wide Zoom*
Displays conventional 4:3
broadcasts with an
imitation wide screen
effect. The 4:3 picture is
stretched to fill the screen.
Normal
Displays conventional 4:3
broadcasts (e.g. non-wide
screen TV) in the correct
proportions.
15 GB
Watching TV
z
• When four coloured items appear at the bottom of the
Text page, Fastext is available. Fastext allows you to
access pages quickly and easily. Press the corresponding
coloured button to access the page.
Using the Digital Electronic Programme Guide
(EPG)
*
GUIDE
Fri 16 Mar 11:35
Today
11: 30
001
BBC ONE
Homes Under the Hammer
002
BBC TWO
Ready Steady Cook
003
ITV1
Dancing On Ice Exclusive
004
Channel 4
Sign Zone: Ancient Rome: The Rise a...
005
Five
House
006
ITV2
Crime Hour: Midsomer Murders
007
BBC THREE
BBC Learning Zone: Schools: World P...
008
BBC FOUR
009
ITV3
010
SKY THREE
011
More 4
12: 00
13: 00
Afterlife
Extraordinary People: Britains Iden...
CSI: Crime Scene Inv...
Cracker
The Jeremy Kyle...
Law and Order: Special Victims U...
ER
P
12: 30
Neighbours
Vodafone TBA: L...
A Picture of Brit...
Real Crime: The Truth About the...
Everybody Loves Raymond
Racing from Chepstow and Ascot
Homes Under th...
PartyPoker.com Worl...
1
2
In digital mode, press GUIDE.
Perform the desired operation as shown
in the following table or displayed on the
screen.
Eastenders
This is BBC FOUR
The Sharon Osb...
Baseball Wedne...
Trans World Sport
Carry On Up The Khyber
Digital Electronic Programme Guide (EPG)
* This function may not be available in some countries/regions.
To
Do this
Watch a programme
Press F/f/G/g to select the programme, then press
Turn off the EPG
Press GUIDE.
.
~
• If an age restriction for programmes has been selected, a message asking for a PIN code will appear on the screen. For
details, see “Parental Lock” on page 36.
16 GB
Using the Digital Favourite list
Favourite Set-up
Favourites 1
The Favourite feature allows you to specify up to
four lists of your favourite programmes.
Digital
Enter Programme Number:
BBC ONE
010
More 4
002
BBC TWO
011
abc1
003
ITV1
012
QVC
004
Channel 4
013
UKTV Gold
005
Five
014
The HITS
006
BBC Three
015
UKTV Bright Ideas
007
ITV2
016
ftn
008
Sky Sports
017
TMF
009
UKTV History
018
E4
000
1
In digital mode, press HOME, and select
“Digital Favourites”.
2
Perform the desired operation as shown
in the following table or displayed on the
screen.
Digital Favourite list
* This function may not be available in some countries/regions.
To
Do this
Create your Favourite list for the first
time
1 Press to select “Yes”.
2 Press the yellow button to select the Favourite list.
3 Press F/f/G/g to select the channel you want to add, then
press .
Channels that are stored in the Favourite list are indicated by a
symbol.
4 Press
RETURN to finish setting up.
Watch a channel
1 Press the yellow button to navigate through your Favourite
lists.
2 Press F/f to select the channel, then press .
Turn off the Favourite list
Press
Add or remove channels in the
currently edited Favourite list
1 Press the blue button.
2 Press the yellow button to select the Favourite list you want to
edit.
3 Press F/f/G/g to select the channel you want to add or
remove, then press .
Remove all channels from the current
Favourite list
1 Press the blue button.
2 Press the yellow button to select the Favourite list you want to
edit.
3 Press the blue button.
4 Press G/g to select “Yes”, then press to confirm.
RETURN.
17 GB
Watching TV
001
*
Playing a DVD
Getting ready
1
Playing a DVD
Press 1 on the TV, or "/1 on the remote
to turn on the TV.
The Standby indicator on the front panel of the
TV changes to green from red.
2
Playing a title
1
~
Press
to select the DVD mode.
• Depending on the DVD in use, you may be required
to select a title or chapter from the DVD content.
The input source menu appears on the screen.
3
Press F/f to select DVD, then press
confirm.
to
Your TV will switch to the DVD mode.
Inserting a disc
1
After the DVD is read, playback starts
automatically.
Hold the disc with the printed side facing
you, and push it lightly into the disc bay
until it is taken in automatically. Please
see following illustration:
2
3
4
Press X to pause playback.
Press N or X to resume playback.
Press x to stop playback.
Displaying information
1
2
Press
/
to view the information line.
Press
/
to hide the information line.
Selecting a title or chapter through the
DVD menu
DVD contains various titles and chapters that you
may select. The number of titles or chapters on the
DVD is displayed in the information item next to the
title and chapter indicator.
1
The DVD’s title menu (if any) appears on the
screen.
z
• DVD playback starts automatically.
• If
appears on TV, the currently-selected function
cannot be used with the disc.
• Enter the DVD mode in the following way.
– Press
/
to select DVD input.
– Press HOME and select “DVD”.
– Insert the disc.
– Press N. (Only when BRAVIA Sync is not
activated.)
~
• Insert the disc halfway, and it will automatically be
inserted in the disc bay.
• Do not push or pull an inserted disc, as malfunction or
damage may result.
• Do not insert an unsupported disc or foreign object into
the disc bay, as a malfunction may result.
Ejecting a disc
1
Press Z on the side panel of the TV.
Remove the disc.
18 GB
Press OPTIONS and select “Top Menu”
to open the DVD content.
2
Press F/f or G/g to select a title or
chapter, then press
to start playback.
3
Playback starts from the selected title/
chapter.
Selecting a title or chapter through the
Info menu
This function depends on the DVD in use.
1
Press the number buttons to display the
title/chapter selection screen during
playback.
2
3
Press G/g to select a title or chapter.
4
Playback starts with the selected title or
chapter number.
Press the number buttons to enter the title
or chapter number.
Step-by-step chapter selection
1
Press > to select the next chapter
during playback.
2
Press . to select the previous chapter
during playback.
Switching the dubbing language or audio
format
Use this setting to change the preset dubbing
language if the DVD contains alternatives.
1
You can pause or resume playback of a DVD as
desired.
Press x once to pause playback.
Press N or X to resume playback.
Playback resumes from the point it was
paused.
2
Press AUDIO repeatedly to select the
dubbing language.
~
Searching for a point in a disc
Press m or M during playback. When you find
the point you want, press N to return to normal
speed. Each time you press m or M during scan,
the scan speed changes. With each press the
indication changes as shown below. Actual speeds
may differ between discs.
Playback direction
• A DVD’s structure may prevent you from changing the
audio language. In this case, you can generally make the
setting from the DVD menu.
Selecting and displaying subtitles
If a DVD contains subtitles, they can be displayed on
the screen. If there are subtitles in multiple
languages, you can select the desired language.
1
Press
during playback.
For example, the following information, which
indicates the current subtitle language, appears
on the screen briefly:
Subtitle 01/05 German
Opposite direction
2
Keep pressing
language.
to select the subtitle
~
• To turn the subtitles off, press
repeatedly until
“Subtitle Off” appears on the screen.
• Switching between subtitle languages may be
prevented by the DVD’s own structure. In this case,
you can generally make the setting from the DVD
menu.
Slow forward and slow reverse
You can slow play by pressing m or M in pause
mode.
Each time you press m or M during slow play,
the playback speed changes. Four speeds are
available. With each press the indication changes as
follows:
Playback direction
Opposite direction (DVD only)
The “
4”/“
4” playback speed is slower than
“
1”/“
1”.
Camera angle selection for certain scenes
and passages
Some DVDs contain scenes or passages shot from
different camera angles. You can select one of these
different angles.
1
Press OPTIONS and select “Angle”
during playback.
2
Press
with “Angle” selected to select
another camera angle.
Continued
19 GB
Watching TV
For example, the following information, which
indicates the current dubbing language, appears
on the screen briefly:
Audio 1/4: Dolby Digital 3/2.1 CH English
“Audio 1/4” in the above example indicates that
the first of the 4 dubbing languages is selected.
“Dolby Digital 5.1ch” indicates that the audio
format is Dolby Digital.
Pausing or resuming playback
1
2
3
Press AUDIO during playback.
S-VCD/VCD Playback
Playing audio data
1
Insert CD containing audio data to the TV,
and the file browser appears
automatically.
2
Press F/f to select the directory, then
press
to open it.
PBC (playback control)
This is the navigation option for PBC, S-VCD/
VCDs. PBC information is stored in the disc at the
factory.
PBC is activated when it is ready for delivery. PBC
and channel information in the S-VCD/VCD
indicate the navigation options.
To activate PBC
Press x twice, then press N to start playback.
To deactivate PBC
Press number buttons to select the title during
playback.
z
The subdirectory list appears on the screen.
3
4
5
6
7
• While PBC is on, press OPTIONS and select “Top
Menu” to display the PBC navigation on the screen.
Playing Sound/Picture Data
Playing Picture CD
1
Insert CD containing picture data to the
TV, and the file browser appears
automatically.
2
Press F/f to select the directory, then
press
to open it.
The subdirectory list appears on the screen.
3
4
5
Press F/f to select the picture.
Press
or N to display the picture.
Press x to end playback.
z
• If you press N during playback, the screen changes to
the slideshow.
Press x to stop the slideshow, and press again to return
to the file browser.
Rotating the picture
Pictures can be rotated 90°.
1
Press G or g to rotate pictures 90° during
playback.
Flipping the picture
Pictures can be flipped.
1
Press F or f to flip pictures during
playback.
20 GB
Press F/f to select the title.
Press
or N to start playback.
Press X to pause playback.
Press N or X to resume playback.
Press > to select the next title, or .
to select the previous title.
or
Press the number buttons to enter the title
number, then press
to start playback.
8
Press x to end playback.
Enjoying Karaoke
Using Karaoke
You can enjoy karaoke by setting this TV to karaoke
mode. You can connect a microphone (not supplied)
to the TV.
Watching TV
~
• When the input source is TV or USB photo/music/video,
karaoke cannot be used.
• The voice input from microphone is not output from the
audio output jacks of the TV or Sony/Phillips Digital
Interface. Neither “Key Change” or “Vocal Reducer”
(page 32) are applied to the audio output signal.
• When karaoke is used, video and audio from Scart
connection cannot be output.
1
Connect the microphone to the side panel
of the TV.
2
Select the input source except TV and
USB.
3
4
Press HOME and select “Karaoke”.
Set the Karaoke mode to “On” (page 32).
~
• Do not bring the microphone close to TV as howling
may result.
• During a thunderstorm, stop the karaoke function and
disconnect the microphone.
• Do not output sound beyond the ratings of the TV. If you
input a loud voice, the sound may be distorted.
• If you do not use the karaoke function, set it to “Off”.
Otherwise, noise may be input from the microphone.
• The Vocal Reducer function may not be effective
depending on the source. If you use Karaoke DVD/CD,
set “Vocal Reducer” to “Off” (page 32).
21 GB
Using Optional Equipment
Connecting optional equipment
You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.
DVD player
PC (HDMI output)
Blu-ray disc player
Digital video
camera
PC
Decoder
Video game
equipment
DVD player
Decoder
DVD recorder
VCR
Hi-Fi audio equipment
with optical audio input
Hi-Fi audio
equipment
DVD player with
component output
CAM card
Digital video camera/Digital
camera/USB storage
Video game
equipment/
DVC camcorder
Headphones
Microphone
22 GB
Viewing pictures from
connected equipment
Symbol on the
screen
PC
For an auto-tuned VCR page 6
In analogue mode, press PROG/CH +/–, or the
number buttons, to select the video channel.
Digital
Analogue
AV2
To see the equipment connected to
J.
When connecting mono equipment,
connect to the
AV2 L socket.
~
• Be sure to use only an authorised HDMI cable bearing
the HDMI logo. We recommend that you use a Sony
HDMI cable.
• When HDMI control compatible equipment is
connected, communication with the connected
equipment is supported. Refer to page 27 to set up this
communication.
AV1
To connect
AV2
HDMI1
Conditional
To use Pay Per View services.
Access Module For details, refer to the instruction
(CAM) H
manual supplied with your CAM.
Turn off the TV when inserting or
removing your CAM.
~
HDMI2
DVD
Component
PC
For a USB device
See page 24.
Symbol on the
screen
• CAM is not supported in some
countries/regions. Check with your
authorised dealer.
Description
USB I
You can enjoy photo/music/video
files stored in a Sony digital still
camera or camcorder (page 24).
Hi-Fi audio
equipment F
Connect to the audio output sockets
to listen to the sound from the
TV on Hi-Fi audio equipment.
Audio level of the external speakers
can be modified by pressing the
volume buttons on the remote.
Component To see the equipment connected to
G.
HDMI1 or HDMI IN 1 or HDMI IN 2
HDMI2
To see the equipment connected to
A or B.
Digital video and audio signals are
input from the connected equipment.
If the equipment has a DVI socket,
connect the DVI socket to the HDMI
IN 1 socket through a DVI-HDMI
adaptor interface (not supplied), and
connect the equipment’s audio out
sockets to the audio in sockets in the
HDMI IN 1 sockets.
Connect to the HDMI IN 2 socket,
to view photographs or screen
images from a PC or digital video
camera.
AV1
Do this
DIGITAL
Use an optical audio cable.
AUDIO OUT
(OPTICAL) E
iK
Connect to the i socket to listen to
sound from the TV on headphones.
mL
Connect a microphone to the m
socket to enjoy the karaoke function.
To see the equipment connected to
D.
Continued
23 GB
Using Optional Equipment
Inputs
To see the equipment connected to
C.
z
• It is recommended to use a PC cable
with ferrites like the “Connector, Dsub 15” (ref. 1-793-504-11,
available in Sony Service Centre), or
equivalent.
Turn on the connected equipment, then
perform one of the following operation.
For other connected equipment
Press
to display the connected equipment list.
Press F/f to select the desired input source, then
press . (The highlighted item is selected if two
seconds pass without any operation after pressing F/
f.)
Description
Additional operation
To
Do this
Return to normal
TV mode
Press DIGITAL/ANALOG.
Playing Back Photo/Music/
Video via USB
You can enjoy photo/music/video files stored in a
Sony digital still camera or camcorder through a
USB cable or USB storage device on your TV.
1
2
3
Connect a supported USB device to the TV.
Press HOME.
Press F/f to select “Photo”, “Music”, or
“Video”, then press .
The file or folder list appears.
4
Press F/f/G/g to select a file or folder,
then press .
When you select a folder, select a file, then press
.
Playback starts.
~
• Picture quality may appear coarse when using “Photo”
because images may be enlarged depending on the file.
Also, images may not fill the entire screen depending on
the image size and aspect ratio.
• Some photo files may take some time to be displayed
when using “Photo”.
• The file name and folder name support the UTF-8
character set.
• While the TV is accessing the data on the USB device,
observe the following:
– Do not turn off the TV or connected USB device.
– Do not disconnect the USB cable.
– Do not remove the USB device.
The data on the USB device may be damaged.
• Sony will not be held liable for any damage to, or loss of,
data on the recording media due to a malfunction of any
connected devices or the TV.
• When you connect a Sony digital still camera, set the
camera’s USB connection mode to Auto or “Mass
Storage”. For more information about USB connection
mode, refer to the instructions supplied with your digital
camera.
• USB Photo Viewer supports FAT16 and FAT32 file
systems.
• BRAVIA TV supports DivX® (not available for DVD).
• Up to 300 files per folder are supported.
• Depending on the exact file specifications, some files,
including those modified on a PC, cannot be played even
if the file format is supported.
• Check the website below for updated information about
compatible USB devices.
http://support.sony-europe.com/TV/compatibility/
24 GB
Basic operation of Photo/Music/Video
To set the picture (Video)
You can operate the connected USB device by the
TV remote.
You can adjust the picture quality of USB Video.
Item
Description
m/M
Fast reverses/fast forwards the file when
pressed during playback.
./>
Goes to the beginning of the previous/
next file.
N
Starts playback.
X
Pauses playback.
x
Stops playback.
To use playback options
Select a video.
See “Playing Back Photo/Music/Video via
USB” (page 24).
2
Press OPTIONS during playback, then
press F/f to select “Picture” and press .
3
Press F/f/G/g to select the item, then
press .
4
Press F/f/G/g to adjust the setting, then
press .
To play a photo as a slideshow (Photo)
You can play a slideshow with photos. “Slideshow
Effect” and “Slideshow Speed” can be set.
1
Select a photo.
See “Playing Back Photo/Music/Video via
USB” (page 24).
2
Press the green button in thumbnail view,
or press OPTIONS while a photo is
displayed, then press F/f to select
“Slideshow” and press .
To stop a slideshow
Press
RETURN or HOME.
Continued
25 GB
Using Optional Equipment
Press the coloured buttons to display a list that
contains shortcuts to some setting menus. The listed
options vary depending on the current input and
content.
Photo
“Slideshow Effect”: Selects an effect for a
slideshow.
“Slideshow Speed”: Selects the slideshow duration.
“Shuffle”: Plays a file in random order.
“Zoom”: Magnifies the picture (“1×”, “2×” or “4×”)
Music
“Playback Target”: Selects to play all files, or one
selected file.
“Shuffle”: Plays files in random order.
“Speakers”: Selects a speaker (page 31).
Video
“Playback Target”: Selects to play all files, or one
selected file.
“Zoom”*: Magnifies the picture (“1×”, “2×”, “4×”
or “Full”)
“Speakers”: Selects a speaker (page 31).
* When you set “Zoom”, stop video playback.
General
“Repeat”: Plays a file repeatedly.
“Sort By”: Changes file order
“Device Selection”: Selects a USB device.
1
USB Video format
Extension
Container
.avi
AVI
Video Codec
DivX 3.11/4.x/5.1
Audio Codec
XviD
PCM / MPEG1 Layer1, 2 / MP3 /
MPEG2 AAC (2ch) /
MPEG4 AAC (2ch) /
MPEG4 HE-AAC (2ch) /
Dolby Digital (2ch) / WMA v8
MPEG1
MPEG2 MP
H.264 BP/MP/HP
MPEG-4 SP/ASP
WMV v9
DivX 3.11
.wmv
.asf
ASF
XviD
MP3 / WMA v8
MPEG-4 SP/ASP
VC-1
H.264 BP/MP/HP
.mp4
.mov
.3gp
MP4
MPEG-4 SP/ASP
MPEG1 Layer1, 2 / MP3 / MPEG2 AAC /
MPEG4 AAC / MPEG4 HE-AAC
H.263
H.264 BP/MP/HP
MPEG-4 SP/ASP
.mkv
MKV
WMV v9
DivX 3.11/4.x/5.1
PCM / MPEG1 Layer1, 2 / MP3 /
MPEG2 AAC (2ch) /
MPEG4 AAC (2ch) /
MPEG4 HE-AAC (2ch) /
Dolby Digital (2ch) / WMA v8
VC-1
MPEG1
.mpg
.mpeg
.vob
PS
MPEG2 MP
MPEG1 Layer1, 2 / MP3 /
Dolby Digital (2ch)
MPEG2 MP
.ts, .m2ts
TS
VC-1
H.264 BP/MP/HP
USB Music format
Extension
.mp3
Audio Codec
MP3
.wma
WMA v8
USB Photo format
Extension
.jpg, .jpeg
Image Codec
JPEG
DCF2.0 or EXIF2.21 supported.
~
• Playback of the above file formats is not guaranteed.
26 GB
MPEG1 Layer1, 2 / MP3 / MPEG2 AAC /
MPEG4 AAC / MPEG4 HE-AAC
Using BRAVIA Sync with
Control for HDMI
The Control for HDMI function enables the
TV to communicate with the connected
equipment that is compatible with the
function, using HDMI CEC (Consumer
Electronics Control).
For example, by connecting Sony equipment
that is compatible with Control for HDMI (with
HDMI cables), you can control them together.
Be sure to connect the equipment correctly,
and make the necessary settings.
To make the Control for HDMI settings
The Control for HDMI settings must be set on
both the TV side and connected equipment
side. See “HDMI Set-up” page 37 for the TV
side settings. For settings on the connected
equipment, refer to the operating instructions
for that equipment.
Using Optional Equipment
Control for HDMI
• Automatically turns the connected equipment
off when you switch the TV to standby mode
using the remote.
• Automatically turns the TV on and switches
the input to the connected equipment when the
equipment starts to play.
• If you turn on a connected audio system while
the TV is on, the sound output switches from
the TV speaker to the audio system.
• Adjusts the volume (2 +/–) and mutes the
sound (%) of a connected audio system.
• You can operate the connected Sony
equipment that has the BRAVIA Sync logo by
the TV remote by pressing:
– m/N/X/M/./x/> to operate the
connected equipment directly.
– SYNC MENU to display the menu of the connected
HDMI equipment on the screen.
After displaying the menu, you can operate the
menu screen by using F/f/G/g, , colour buttons,
RETURN.
and
– Select “Device Control”, then select the desired
option to operate the equipment.
– Refer to the instruction manual of the equipment
for available control.
– Select “TV Control” to open the TV Menu or TV
options menu.
•
If “Control for HDMI” of the TV is set to
“On”, “Control for HDMI” of the connected
equipment is also automatically switched to
“On”.
To connect the equipment that is
compatible with Control for HDMI
Connect the compatible equipment and the TV
with an HDMI cable. When connecting an
audio system, be sure to also connect the
DIGITAL AUDIO OUT (OPTICAL) jack of
the TV and the audio system using an optical
audio cable (page 22).
27 GB
Using MENU Functions
Navigating through TV Menu
“MENU” allows you to enjoy various convenient features of this TV. You can easily select channels
or inputs sources and change the settings for your TV.
1
Press HOME.
HOME
Digital Favourites
Digital EPG
Photo
Music
Video
DVD
Karaoke
Settings
2
Press F/f to select an option, then press
.
To exit the menu, press HOME.
Media category icon
Description
Digital Favourites
You can select the Digital Favourite list (page 17).
Digital EPG
You can select the Digital Electronic Programme Guide (EPG) (page
16).
Photo
You can enjoy photo files via USB devices (page 24).
Music
You can enjoy music files via USB devices (page 24).
Video
You can enjoy video files via USB devices (page 24).
DVD
Plays a disc inserted in the TV (page 18).
Karaoke
You can enjoy karaoke (page 21).
Settings
You can make advanced settings and adjustments (page 29).
~
• The options you can adjust vary depending on the situation.
• Unavailable options are greyed out or not displayed.
28 GB
Settings
Picture
Picture Mode
Selects the picture mode.
“Vivid”: For enhanced picture contrast and sharpness.
“Standard”: For standard picture. Recommended for home entertainment.
“Custom”: Allows you to store your preferred settings.
“Cinema”: For film-based content. Suitable in a theatre-like environment.
“Photo”: For standard viewing of photographs.
“Sports”: Optimises picture quality for viewing sports.
“Game”: For standard picture suitable for games.
“Graphics”: Optimises picture quality for viewing graphics.
~
• “Picture Mode” is set depending on “Scene Select” settings.
Reset
Resets all “Picture” settings except “Picture Mode” to the factory settings.
Backlight
Adjusts the brightness of the backlight.
~
• Reducing the brightness of the screen, the power consumption will be reduced.
Increases or decreases picture contrast.
Brightness
Brightens or darkens the picture.
Colour
Increases or decreases colour intensity.
Hue
Increases or decreases the green tones and red tones.
Using MENU Functions
Contrast
z
• “Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes).
Sharpness
Sharpens or softens the picture.
Colour Temperature
Adjusts the whiteness of the picture.
“Cool”: Gives the white colours a blue tint.
“Neutral”: Gives the white colours a neutral tint.
“Warm”: Gives the white colours a red tint.
Noise Reduction
Reduces the picture noise (snowy picture) in a weak broadcast signal.
“Auto/High/Medium/Low”: Modifies the effect of the noise reduction.
“Off”: Turns off the “Noise Reduction” feature.
MPEG Noise
Reduction
Reduces the picture noise in MPEG-compressed video.
Continued
29 GB
Film Mode
Provides improved picture movement when playing DVD or VCR images taken on
film, reducing picture blur and graininess.
“Auto”: Provides the original film-based content as is.
“Off”: Turns off the “Film Mode” feature.
~
• If the image contains irregular signals or too much noise, “Film Mode” is automatically
turned off even if “Auto” is selected.
Advanced Settings
Customises the Picture function in more detail.
“Reset”: Resets all the advanced settings to the factory settings.
“Adv. Contrast Enhancer”: Automatically adjusts “Backlight” and “Contrast” to
the most suitable settings judging from the brightness of the screen. This setting is
especially effective for dark images scenes, and will increase the contrast distinction
of the darker picture scenes.
“Black Corrector”: Enhances black areas of the picture for stronger contrast.
“Gamma”: Adjusts the balance between bright and dark areas of the picture.
“Clear White”: Emphasises white colours.
“Live Colour”: Makes colours more vivid.
~
• “Advanced Settings” is not available when “Picture Mode” is set to “Vivid” or for USB (Video) input.
Sound
Sound Mode
Selects the sound mode.
“Dynamic”: Intensifies clarity and sound presence for better intelligibility and
musical realism.
“Standard”: Enhances clarity, detail, and sound presence.
“Clear Voice”: Makes voice sound clearer.
Reset
Resets all the “Sound” settings to the factory settings.
Equalizer
Adjusts sound frequency settings.
Press G/g to select the desired sound frequency, then press F/f to adjust the setting
and press . The adjusted settings will be received when you select “Sound Mode”
options. Selecting “Reset” will set the “Equalizer” to original settings.
~
• Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency
will affect lower pitched sound.
Balance
Emphasises left or right speaker balance.
Auto Volume
Keeps a constant volume level even when volume level gaps occur (e.g., adverts tend
to be louder than programmes).
Volume Offset
Sets an independent volume level to each equipment connected to the TV.
30 GB
Surround
Selects the surround mode.
“On”: Delivers surround effects that help you enjoy the virtual two-ch surround
audio with just the two internal TV speakers.
“Simulated Stereo”: Adds a surround-like effect to mono programmes.
“Cinema”: Delivers surround effects just like the high-grade audio systems found
in movie theatres.
“Music”: Delivers surround effects that make you feel like you are surrounded by
sound as in a music hall.
“Sports”: Delivers surround effects that make you feel like you are watching a live
sports contest.
“Game”: Delivers surround effects that enhance game sound.
“Off”: For normal stereo or mono reception.
~
• “Surround” is set depending on “Scene Select” settings.
Bass Booster
Produces a fuller sound for more impact, by emphasising the bass sounds.
Dual Sound
Selects the sound from the speaker for a stereo or bilingual broadcast.
“Stereo”, “Mono”: For a stereo broadcast.
“A”/“B”/“Mono”: For a bilingual broadcast, select “A” for sound channel 1, “B”
for sound channel 2, or “Mono” for a mono channel, if available.
z
• If you select other equipment connected to the TV, set “Dual Sound” to “Stereo”, “A” or “B”.
Turns on/off the TV’s internal speakers.
“TV Speakers”: The TV speakers are turned on in order to listen to the TV’s sound
through the TV speakers.
“Audio System”: The TV speakers are turned off in order to listen to the TV’s sound
only through your external audio equipment connected to the audio output sockets.
Audio Out
“Variable”: When using an external audio system, volume output from audio out
can be controlled using the TV’s remote.
“Fixed”: The audio output of the TV is fixed. Use your audio receiver’s volume
control to adjust the volume (and other audio settings) through your audio system.
Headphone Speaker Switches the TV’s internal speakers on/off when you connect headphones to the TV.
Link
Headphone Volume
Adjusts the volume of the headphones.
HDMI/DVI Audio
Source
Switches the audio signal for HDMI input when a DVI device is connected. Select
from “Auto”, “HDMI Audio” and “PC Audio”.
Advanced Settings
“Dynamic Range”: Compensates for differences in the audio level between
different channels (only for Dolby Digital audio).
~
• The effect may not function or may vary depending on the programme regardless of the
“Dynamic Range” setting.
“Optical Out”: Sets the audio signal that is output from the DIGITAL AUDIO OUT
(OPTICAL) jack of the TV. Set to “Auto”, when connecting equipment compatible
with Dolby Digital. Set to “PCM”, when connecting equipment not compatible with
Dolby Digital.
“Downmix Mode”: Set the downmix method of multi-channel to two-channel
sound.
• “Surround”: Select to get best surround performance, or while using external products with
Pro Logic.
• “Stereo”: Select to get a stereo output.
Continued
31 GB
Using MENU Functions
Speakers
Karaoke
“Karaoke”: Selects the karaoke mode, “On” or “Off”.
“Key Change”: Changes the key of music. The key can be adjusted by semitone
steps.
“Vocal Reducer”: Reduces the volume of the vocal part in the music. The
effectiveness of function depends on the music type.
“Mic1 Volume/Mic2 Volume”: Adjusts the volume of Microphone 1 and 2.
~
• “Sound Mode”, “Reset”, “Equalizer”, “Balance”, “Auto Volume”, “Volume Offset”, “Surround”, “Bass Booster” and
“Karaoke” are not available when “Speakers” is set to “Audio System”.
Screen
Screen Format
Changes the screen format. For details about the screen format, see page 15.
Screen Format
(only in PC mode)
“Normal”: Displays the picture in its original size.
“Full 1”: Enlarges the picture to fill the vertical display area, while maintaining its
original proportion.
“Full 2”: Enlarges the picture to fill the display area.
Auto Format
“On”: Select “On” to automatically change “Screen Format” setting based on the
content.
“Off”: If frequent screen changes are disturbing to you, select “Off”. Choose one of
the “Screen Format” options when this function is set to “Off”.
4:3 Default
Sets the default screen format for 4:3 broadcasts.
Auto Display Area
“On”: Automatically adjusts the display area based upon the content.
“Off”: Turns off the “Auto Display Area”. Choose one from the “Display Area”
options.
Display Area
Adjusts the picture display area.
“Full Pixel”: Displays pictures in their original size when parts of the picture are cut
off.
“Normal”: Displays pictures in their recommended size.
“+1”: Displays pictures in their original size.
“-1”: Enlarges the picture so that the edges are outside the visible display area.
~
• These options may change depending on the input displayed.
Horizontal Shift
Adjusts the horizontal position of the picture.
Vertical Shift
Adjusts the vertical position of the picture when “Screen Format” is set to “Zoom”,
“14:9” or “Captions”.
Vertical Size
Adjusts the vertical size of the picture when “Screen Format” is set to “Wide Zoom”.
32 GB
PC Adjustment
Customises the TV screen as a PC monitor.
z
• This option is only available if a PC signal is received.
• “Auto Adjustment” may not work well with certain input signals. In such cases, manually
adjust “Phase”, “Pitch”, “Horizontal Shift”, and “Vertical Shift”.
“Screen Format”: Select “Normal” to display in the original image size. Select
“Full 1” to enlarge the picture to fill the display area, keeping its original aspect ratio.
Select “Full 2” to enlarge the picture to fill the display area.
“Reset”: Resets all the “PC Adjustment” except “Screen Format” to the factory
settings.
“Auto Adjustment”: Automatically adjusts the display position, and phase of the
picture in PC mode.
“Phase”: Adjusts the screen when a part of a displayed text or image is not clear.
“Pitch”: Enlarges or shrinks the screen size horizontally.
“Horizontal Shift”: Moves the screen to the left or to the right.
“Vertical Shift”: Moves the screen up or down.
Channel Set-up
Analogue Set-up
System
Presets programme channels manually.
1 Press F/f to select “System”, then press .
2 Press F/f to select one of the following TV broadcast systems, then
press .
B/G: For western European countries/regions
I: For the United Kingdom
D/K: For eastern European countries/regions
L: For France
~
• Depending on the country/region selected for “Country”, this option may not be available.
Channel
1 Press F/f to select “Channel”, then press .
2 Press F/f to select “S” (for cable channels) or “C” (for terrestrial
channels), then press g.
3 Tune the channels as follows:
If you do not know the channel number (frequency)
Press F/f to search for the next available channel. When a channel has been found,
the search will stop. To continue searching, press F/f.
If you know the channel number (frequency)
Press the number buttons to enter the channel number of the broadcast you want or
your VCR channel number.
4
Press
to jump to “Confirm”, then press
.
Repeat the procedure above to preset other channels manually.
Continued
33 GB
Using MENU Functions
“Analogue Auto Tuning” (Only in analogue mode): Tunes in all the available
analogue channels. Usually you do not need to do this operation because the
channels are already tuned when the TV was first installed. However, this option
allows you to repeat the process (e.g., to retune the TV after moving house, or to
search for new channels that have been launched by broadcasters).
“Manual Programme Preset” (Only in analogue mode): Changes the available
analogue channel setting.
Press
to select the programme you want to modify.
Label
Assigns a name of your choice, up to five letters or numbers, to the selected channel.
AFT
Allows you to fine-tune the selected programme number manually if you feel that a
slight tuning adjustment will improve the picture quality.
Audio Filter
Improves the sound for individual channels in the case of distortion in mono
broadcasts. Sometimes a non-standard broadcast signal can cause sound distortion or
intermittent sound muting when watching mono programmes.
If you do not experience any sound distortion, we recommend that you leave this
option set to the factory setting “Off”.
~
• “Audio Filter” is not available when “System” is set to “L”.
Skip
Skips unused analogue channels when you press PROG/CH +/- to select channels.
(You can still select a skipped channel using the number buttons.)
Confirm
Saves changes made to the “Manual Programme Preset” settings.
“Programme Sorting” (Only in analogue mode): Changes the order in which the
analogue channels are stored on the TV.
1 Press F/f to select the channel you want to move to a new position,
then press g.
2 Press F/f to select the new position for your channel, then press .
Digital Set-up
“Digital Tuning”
• “Digital Auto Tuning”:
Tunes in the available digital channels.
This option allows you to retune the TV after moving house, or to search for new
channels that have been launched by broadcasters. Press .
• “Programme List Edit”:
Removes any unwanted digital channels stored on the TV, and changes the order
of the digital channels stored on the TV.
1 Press F/f to select the channel you want to remove or move to a new
position.
Press the number buttons to enter the known three-digit programme number of the
broadcast you want.
2 Remove or change the order of the digital channels as follows:
To remove the digital channel
Press
. After a confirmation message appears, press G to select “Yes”, then press
To change the order of the digital channels
Press g, then press F/f to select the new position for the channel and press G.
3 Press
RETURN.
~
• When “Cable” is selected this function may not be available in some countries.
• “Digital Manual Tuning”:
Tunes the digital channels manually.
1 Press the number button to select the channel number you want to
manually tune, then press F/f to tune the channel.
2 When the available channels are found, press
to store programmes.
Repeat the above procedure to manually tune other channels.
~
• Not available for Cable connection.
34 GB
.
“Subtitle Set-up”
• “Subtitle Setting”: When “For Hard Of Hearing” is selected, some visual aids
may also be displayed with the subtitles (if TV channels broadcast such
information).
• “Primary Preferred Language”: Selects preferred language which subtitles are
displayed in.
• “Secondary Preferred Language”: Selects secondary preferred language which
subtitles are displayed in.
“Audio Set-up”
• “Audio Type”: Switches to broadcast for the hearing impaired when “For Hard
Of Hearing” is selected.
• “Primary Preferred Language”: Selects the preferred language used for a
programme. Some digital channels may broadcast several audio languages for a
programme.
• “Secondary Preferred Language”: Selects the secondary preferred language
used for a programme. Some digital channels may broadcast several audio
languages for a programme.
• “Audio Description”: Provides audio description (narration) of visual
information if TV channels broadcast such information.
• “Mixing Level”: Adjusts the TV main audio and Audio Description output levels.
z
• This option is only available when “Audio Description” is set to “On”.
• “MPEG Audio Level”: Adjusts the MPEG audio sound level.
~
• When “Cable” is selected this function may not be available in some countries.
• “Auto DST”: Sets whether or not to automatically switch between summer time
and winter time.
• “On”: Automatically switches between summer time and winter time according to the
calendar.
• “Off”: The time is displayed according to the time difference set by “Time Zone”.
~
• When “Cable” is selected this function may not be available in some countries.
• “Service Replacement”: Select “On” to automatically change the channel when
broadcaster changes transmission of the viewing programme to a different
channel.
“CA Module Set-up”
Allows you to access a pay TV service once you obtain a Conditional Access Module (CAM)
and a view card. See page 22 for the location of the
(PCMCIA) socket.
35 GB
Using MENU Functions
“Technical Set-up”
• “Auto Service Update”: Enables the TV to detect and store new digital services
as they become available.
• “System Update”: This TV set is capable of receiving software upgrades via the
broadcast signal. In order to receive upgrades the System Update option in the
Technical Setup menu should be set to “On”. When an upgrade is detected the user
will be informed by a series of on screen displays on how to proceed with the
upgrade. Please do not disconnect the set from the mains during the installation
procedure.
• “System Information”: Displays the current software version and the signal
level.
• “Time Zone”: Allows you to manually select the time zone you are in, if it is not
the same as the default time zone setting for your country/region.
Parental Lock
Sets an age restriction for programmes. Any programme that exceeds the age restriction can only be watched
after a PIN Code is entered correctly.
~
• For cable operators in Netherlands, the PIN code should be entered when the programme rating is above or equal to the age
you specify.
1 Press the number buttons to enter your existing PIN code.
If you have not previously set a PIN, a PIN code entry screen appears. Follow the instructions of “PIN Code” below.
2 Press F/f to select the age restriction or “None” (for unrestricted watching), then press
3 Press
RETURN.
PIN Code
.
To set your PIN for the first time
1 Press the number buttons to enter the new PIN code.
2 Press
RETURN.
To change your PIN
1 Press the number buttons to enter your existing PIN code.
2 Press the number buttons to enter the new PIN code.
3 Press
RETURN.
z
• PIN code 9999 is always accepted.
Change PIN Code
Selects to change your PIN code.
Parental Lock
Select the age of the youngest viewer (3 ~ 18). Select “None” for no registers.
These selectable items may change depending on the country setting.
Digital Programme
Lock
Locks/unlocks programmes and checks the status of programmes.
1 Press the number buttons to enter your existing PIN code or to set the
new one.
2 Press F/f to navigate across the programmes and press
to change
between “Locked” and “Unlocked” status.
External Input Lock
Locks an external input from being watched. To view a blocked external input, select
“Unblocked”.
36 GB
Set-up
USB Auto Start
Automatically enters the thumbnail view of the last played Photo/Music/Video when
the TV is turned on and a USB device is connected to the USB port then turned on.
Sleep Timer
Sets a period of time after which the TV automatically switches itself into standby
mode.
When the “Sleep Timer” is activated, the (Sleep Timer) indicator on the TV front
panel lights up in orange.
z
• When you turn off the TV and turn it on again, “Sleep Timer” is reset to “Off”.
• A notification message appears on the screen one minute before the TV switches to standby
mode.
Starts the initial set-up to select the language, country/region and location, and tune
in all available digital and analogue channels. Usually, you do not need to do this
operation because the language and country/region will have been selected and
channels already tuned when the TV was first installed. However, this option allows
you to repeat the process (e.g., to retune the TV after moving house).
Language
Selects the language in which the menus are displayed.
Start-up Sound
Select “On” to play sound when the TV is turned on. Select “Off” to disable it.
AV Set-up
Assigns a name to any equipment connected to the side and rear sockets. The name
will be displayed briefly on the screen when the equipment is selected.
1 Press F/f to select the desired input source, then press .
2 Press F/f to select the desired option below, then press .
• AV1 (or AV2/HDMI1/HDMI2/Component/PC), CABLE, SAT, VCR, DVD/BD,
HOME THEATRE, GAME, CAM, DIGITAL CAMERA, PC: Uses one of the
preset labels to assign a name to connected equipment.
• “Edit”: Creates your own label.
1 Press F/f to select the desired letter or number (“_” for a blank
space), then press g.
If you input a wrong character
Press G/g to select the wrong character. Then, press F/f to select the correct
character.
2 Repeat the procedure in step 1 until the name is completed, then
press .
HDMI Set-up
Allows the TV to communicate with equipment that is compatible with the control
for HDMI function, and connected to the HDMI sockets of the TV. Note that
communication settings must also be made on the connected equipment.
“Control for HDMI”: Sets whether or not to link the operations of the TV and the
connected equipment that is compatible with control for HDMI.
“Auto Devices Off”: When this is set to “On”, the connected equipment that is
compatible with control for HDMI turns off when you switch the TV to standby
mode using the remote.
“Auto TV On”: When this is set to “On”, the TV turns on when you turn on the
connected equipment that is compatible with control for HDMI.
“HDMI Device List”: Displays a list of connected equipment that is compatible
with control for HDMI.
“Device Control Keys”: If it is set to “Tuning Keys”, you can select a channel tuned
by connected equipment and if it is set to “Menu Keys” you can navigate through the
menus of the connected equipment using the remote.
Continued
37 GB
Using MENU Functions
Auto Start-up
DivX® VOD
“DivX® VOD Registration Code”: Displays the registration code that is required
to play DivX® VOD content.
“DivX® VOD Deregistration Code”: Displays the deregistration code that is
required to play DivX® VOD content.
DVD Settings
“Downmix”: Switches the method for mixing down to 2 channels when you play a
DVD which has Dolby Digital format.
• “Surround”: Multi-channel audio signals are output to 2 channels for enjoying
surround sounds.
• “Stereo”: Multi-channel audio signals are downmixed to 2 channels for use with
TV speakers or headphones.
“Parental Control Settings”: Films on DVDs may completely or partly not be
suitable for children. Such DVDs may contain information that marks the content or
scenes with access levels between 1 and 8. You can select one of the access levels
and allow alternative scenes to be used during playback.
1 Press F/f to select “Parental Control Settings”, then press .
2 Press F/f to select “PIN code”, then press .
3 Press the number buttons to input the current PIN code.
4 Select “DVD Parental Control”, then press .
5 Press F/f to select the access level, then press .
• “PIN Code”: Allows you to set up the TV to block DVD content. Use 0-9 on the
remote to enter a four-digit PIN code.
• “DVD Parental Control”: Sets a parental guidance level. Select from “Level1”
to “Level8” and “No Restrictions”.
“DVD Language”: Selects the languages for the on-screen display of the DVD.
USB System Update Updates the TV system using USB memory.
Product Support
Displays your TV’s product information.
Factory Settings
Resets all settings to factory settings. After completing this process, the initial set-up
screen is displayed.
38 GB
Eco
Reset
Resets all the “Eco” settings to the factory settings.
Power Saving
Selects the power saving mode to reduce the power consumption of the TV.
“Standard”: Default settings.
“Reduce”: Reduces the power consumption of the TV.
“Picture Off”: Switches off the picture. You can listen to the sound with the picture
off.
Idle TV Standby
Selects the time (“1h”, “2h” or “4h”) to set the TV into standby mode automatically,
if you do not operate the TV for the specified period of time.
Light Sensor
Automatically optimises the picture settings according to the ambient light in the
room.
~
• Do not put anything over the sensor, doing so may affect its function. Check the position of
the sensor (page 13).
PC Power
Management
When this is set to “On,” turns to standby mode if no PC signal is received. Only
available in PC input.
~
39 GB
Using MENU Functions
• Energy efficiency reduces power consumption and thus saves money by reducing electricity bills.
• When not in use
– If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental
and safety reasons.
– As the TV set is not disconnected from the mains when the TV set is just turned off, pull the plug from the mains to
disconnect the TV set completely.
– However, some TV sets may have features that require the TV set to be left in standby to work correctly.
Additional Information
Installing the Accessories (Wall-Mount Bracket)
To Customers:
For product protection and safety reasons, Sony strongly recommends that installing of your TV be
performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Your TV can be installed using the Wall-Mount Bracket SU-WL100 (sold separately).
• Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the
installation.
• Refer to “Detaching the Table-Top Stand from the TV” (page 7).
~
• Place the TV on the Table-Top Stand, when securing the Mounting Hook.
SU-WL100
Screw
(+PSW4 × 12)
0
5
0
01
5
51
01
02
51
02
Mounting Hook
Note when installing
When using the SU-WL100 Wall-Mount Bracket, the space between the wall and the TV will be 6 cm. Use this
space to route cables to the TV.
6 cm
Sufficient expertise is required for installing this product, especially to determine the strength of the wall for
withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers
or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any
damage or injury caused by mishandling or improper installation.
40 GB
TV installation dimensions table
125
SU-WL100
Screen centre point
Unit: cm
Model name
KDL-22CX32D
Display dimensions
Screen centre
dimension
Length for each mounting angle
Angle (0°)
Angle (20°)
A
B
C
D
E
F
G
H
53.0
34.9
10.2
29.0
12.3
21.1
32.6
28.5
Figures in the above table may differ slightly depending on the installation.
WARNING
The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of
the TV. Refer to “Specifications” (page 42) for its weight.
Screw and Hook locations diagram/table
Hook location
SU-WL100
Model Name
KDL-22CX32D
b
Additional Information
Hook location
SU-WL100
a
b
41 GB
Specifications
System
Panel System
LCD (Liquid Crystal Display) Panel
TV System
Depending on your country/region selection
Analogue: B/G, D/K, L, I
Digital: DVB-T, DVB-C
Colour/Video System
Analogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input)
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC HP@L4.0, MP@L4.0
Channel Coverage
Analogue: 46.25 - 855.25 MHz
Digital: VHF/UHF
Disc formats
DVD+RW, DVD+R, DVD-RW, DVD-R, CD-RW, CD-R
Media formats
DVD video, audio CD, video CD (VCD 1.0/1.1/2.0), S-Video CD
Sound Output
5W + 5W
Region code
Indicated on the rear of the TV.
Input/Output jacks
75 ohm external terminal for VHF/UHF
Aerial
/
AV1
21-pin scart connector including audio/video input, RGB input, S-Video input, and TV audio/video output.
COMPONENT IN
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync/PB/CB: 0.7 Vp-p, 75 ohms/
PR/CR: 0.7 Vp-p, 75 ohms
COMPONENT IN
Audio input (phono jacks)
HDMI IN 1, 2
Video: 1080p, 1080/24p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
PC (see page 43)
Analogue audio (minijack) (HDMI 1 only)
AV2
Video input (phono jack)
AV2
Audio input (phono jacks)
DIGITAL AUDIO
OUT (OPTICAL)
Digital optical jack (Two channel linear PCM, Dolby Digital)
AUDIO OUT
Audio output (Left/Right) (phono jacks)
PC IN
PC Input (15 D-sub) (see page 43)
G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms/
R: 0.7 Vp-p, 75 ohms, H/V Sync: TTL level
PC audio input (minijack)
i
Headphones jack
m 1, 2
Microphone jack
USB port
CAM (Conditional Access Module) slot
DVD
DVD
CD
42 GB
Wavelength: 655 ± 15nm
Power Max: 0.4mW
Wavelength: 790 ± 20nm
Power Max: 0.4mW
Model name KDL-
22CX32D
Power and others
Power Requirements
220–240 V AC, 50 Hz
Energy Efficiency Class
C
Screen Size (measured
diagonally)
Approx. 54.8 cm / 22 inches
Power
in “Home”/ 42.0 W
consumption “Standard”
mode
in “Shop”/
“Vivid”
mode
60 W
Average annual energy
consumption*1
61 kWh
Standby Power
Consumption*2
0.27 W
Off mode Power
Consumption
0.26 W
Display Resolution
1,366 dots (horizontal) × 768 lines (vertical)
Dimensions (with stand) 53.0 × 38.1 × 19.0 cm
(w × h × d) (without
53.0 × 34.9 × 8.1 cm
(Approx.)
stand)
Mass
(Approx.)
(with stand) 6.4 kg
(without
stand)
5.9 kg
Supplied Accessories
Refer to “1: Checking the accessories” on page 4.
Optional Accessories
See “Installing the Accessories (Wall-Mount Bracket)” on page 40.
*1 Energy consumption per year, based on the power consumption of the television operating 4 hours per day for 365 days.
The actual energy consumption will depend on how the television is used.
*2 Specified standby power is reached after the TV finishes necessary internal processes.
Design and specifications are subject to change without notice.
Signals
and HDMI IN 1/2
Horizontal
Horizontal (Pixel) Vertical (Line) frequency
(kHz)
Vertical
Standard
frequency (Hz)
VGA
640
480
31.5
60
VGA
SVGA
800
600
37.9
60
VESA Guidelines
XGA
1024
768
48.4
60
VESA Guidelines
WXGA
1280
768
47.4
60
VESA
WXGA
1280
768
47.8
60
VESA
WXGA
1360
768
47.7
60
VESA
• This TV’s PC input does not support Sync on Green or Composite Sync.
• This TV’s PC input does not support interlaced signals.
• This TV’s PC input supports signals in the above chart with a 60 Hz vertical frequency.
43 GB
Additional Information
PC Input Signal Reference Chart for PC IN
Sound
Troubleshooting
Check whether the 1 (standby) indicator is
flashing in red.
When it is flashing
The self-diagnosis function is activated.
Press 1 on the side of the TV to turn it off,
disconnect the mains lead, and inform your dealer or
Sony service centre.
When it is not flashing
1 Check the items in the tables below.
2 If the problem still persists, have your TV
serviced by qualified service personnel.
z
• For further information, please contact Sony Customer
Information Centre at the address or telephone that
appears on the supplied guarantee.
No sound, but good picture
• Press 2 + or % (Mute).
• Check if the “Speakers” is set to “TV Speakers”
(page 31).
• When using HDMI input with Super Audio CD or DVDAudio, DIGITAL AUDIO OUT (OPTICAL) may not
output audio signals.
Channels
The desired channel cannot be selected
• Switch between digital and analogue mode and select
the desired digital/analogue channel.
Some channels are blank
• Scrambled/Subscription only channel. Subscribe to the
pay TV service.
• Channel is used only for data (no picture or sound).
• Contact the broadcaster for transmission details.
Digital channels are not displayed
• Contact a local installer to find out if digital
transmissions are provided in your area.
• Upgrade to a higher gain aerial.
Picture
No picture (screen is dark) and no sound
• Check the aerial/cable connection.
• Connect the TV to the mains, and press 1 on the side of
the TV.
• If the 1 (standby) indicator lights up in red, press "/1.
No picture or no menu information from
equipment connected to the scart connector
• Press
to display the connected equipment list, then
select the desired input.
• Check the connection between the optional equipment
and the TV.
Double images or ghosting
• Check the aerial/cable connection.
• Check the aerial location and direction.
Only snow and noise appear on the screen
• Check if the aerial is broken or bent.
• Check if the aerial has reached the end of its serviceable
life (three to five years in normal use, one to two years
at the seaside).
Picture or sound noise when viewing a TV
channel
• Adjust “AFT” (Automatic Fine Tuning) to obtain better
picture reception (page 34).
Some tiny black points and/or bright points
appear on the screen
• The picture of a display unit is composed of pixels. Tiny
black points and/or bright points (pixels) on the screen
do not indicate a malfunction.
No colour on programmes
• Select “Reset” (page 29).
No colour or irregular colour when viewing a
signal from the
COMPONENT IN sockets
• Check the connection of the
COMPONENT IN
sockets and check if each sockets are firmly seated in
their respective sockets.
44 GB
General
The TV turns off automatically (the TV enters
standby mode)
• Check if the “Sleep Timer” (page 37) or “Idle TV
Standby” (page 39) is activated.
• If no signal is received and no operation is performed in
the TV mode for 15 minutes, the TV automatically
switches to standby mode.
Distorted picture and/or sound
• Keep the TV away from electrical noise sources such as
cars, motorcycles, hair-dryers or optical equipment.
• When installing optional equipment, leave some space
between the optional equipment and the TV.
• Check the aerial/cable connection.
• Keep the aerial/cable TV cable away from other
connecting cables.
The remote does not function
• Replace the batteries.
HDMI equipment does not appear on “HDMI
Device List”
• Check that your equipment is compatible with control
for HDMI.
If “Store Display Mode: On” is displayed on the
screen
• Your TV is set to “Shop” mode. You need to set “Home”
for “Location” in the “Auto Start-up” procedure again
(page 6).
Keep this Instruction
manual safe you’ll
need it
How the switchover affects your TV equipment:
Your new TV has a digital tuner built in, which means it is ready to receive the Freeview signal by
simply plugging it into your aerial socket (check if you can get digital TV through your aerial now,
or whether you'll have to wait until switchover, at www.digitaluk.co.uk).
When the TV switchover happens in your area, there are at least two occasions when you will need
to re-tune your TV in order to continue receiving your existing TV channels, and also to pick up
new ones. Digital UK, the body leading the digital TV switchover, will advise you when you need
to re-tune during the switchover.
45 GB
Additional Information
Television in the UK is going digital, bringing us all more.
Please see overleaf to find out when your area switches to digital.
Digital UK is the independent, non-profit organisation leading the process of digital TV switchover
in the UK. Digital UK provides impartial information on what people need to do to prepare for the
move to digital, and when they need to do it.
How to re-tune:
1
Press "HOME" on the remote
2
Press F/f to select "Settings", then press
3
Press F/f to select "Channel Set-up", then press
4
Press F/f to select "Digital Set-up", then press
5
Press
to select "Digital Tuning"
6
Press
to select "Digital Auto Tuning"
7
Press G to select "OK" then press
8
Follow the on screen instructions.
.
to start "Digital Auto Tuning"
If you are missing any channels, it may be that they are not available in your area, or that your aerial
needs upgrading.
If you have any questions, please contact Sony on 0844 8466555 or call Digital UK on 0845 6 50 50
50 or visit www.digitaluk.co.uk
†Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends.
Rates may vary for calls from non-BT lines.
46 GB
For useful information about Sony products
4-270-482-11(1)
© 2011 Sony Corporation