Sony KP-65XBR10W User's Manual

D:\810nouhin\4080199111\408019911KP57XBRUC\01COV-KP57XBRUC\01COVUC.fm
masterpage:Cover
4-080-199-11 (1)
Projection TV
Operating Instructions
KP-57XBR10W
KP-65XBR10W
© 2000 Sony Corporation
Model name1[KP-57XBR10W]Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
WARNING
To prevent fire or shock
hazard, do not expose the TV
to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR
PRECAUCION
RIESGO DE CHOQUE ELECTRICO
NO ABRIR
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
To prevent electric shock, do not use this polarized AC
plug with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent blade
exposure.
masterpage:Warning
CAUTION
• Reorient or relocate the receiving antennas.
When using TV games, computers, and similar products
with your projection TV, keep the brightness and contrast
functions at low settings. If a fixed (non-moving) pattern is
left on the screen for long periods of time especially at a
high brightness or contrast setting, the image can be
permanently imprinted onto the screen. These types of
imprints are not covered by your warranty because they
are the result of misuse.
• Increase the separation between the equipment and
receiver.
Note on Caption Vision
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
This television receiver provides display of television
closed captioning in accordance with §15.119 of the FCC
rules.
This document is for the remote control RM-Y907
Note on convergence adjustment
MODELS: KP-57XBR10W, KP-65XBR10W
Before you use your projection TV, make sure to adjust
convergence. For details, see on page 25.
Please keep this notice with the instruction manual.
Note to CATV system installer
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
Use of this television receiver for other than private viewing
of programs broadcast on UHF or VHF or transmitted by
cable companies for the use of the general public may
require authorization from the broadcaster/cable company
and/or program owner.
As an ENERGY STAR Partner, Sony
Corporation has determined that this
product meets the ENERGY STAR
guidelines for energy efficiency.
ATTENTION
Pour prévenir les chocs électriques, ne pas utiliser cette
fiche polarisée avec un prolongateur, une prise de courant
ou une autre sortie de courant, sauf si les lames peuvent
tre inserées à fond sans en laisser aucune partie à
decouvert.
NOTIFICATION
This equipment has been tested and found to comply with
the limits for a Class B digital device pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference with radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
Owner’s Record
The model and serial numbers are located at the rear of
the projection TV, below the Sony logo, on the sticker, and
also on the TV box (white label). Record these numbers in
the spaces provided below. Refer to them whenever you
call upon your Sony dealer regarding this product.
Model No.
Serial No.
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
Open Here For Table of Contents and Remote Control Graphics
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\02WAR.fm
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\03REM.fm
Remote Control
MUTING
(page 26)
In the instructions that
follow, we will refer to
the buttons on your remote control.
Keep this flap unfolded and use this page for
reference.
For a detailed explanation of most buttons, see
“Watching the TV” on page 26.
MUTING
DISPLAY
(page 27)
TV/SAT/
PICTURE
MODE
(page 36)
DISPLAY
FUNCTION
OFF
DVD/
VCR
POWER
SAT/
CABLE
DVD/VCR SAT/CABLE
SWAP POSITION
GUIDE
ZOOM IN
LEFT
RIGHT
ACTIVE
WIDE MODE
(page 29)
SLEEP
(page 27)
AV1/2/3/
DVD/MDP
switch
(page 54)
MUTING
DISPLAY
AV 1 2 3 DVD/MDP
DVD/
VCR
JUMP
(page 26)
POWER
SAT/
CABLE
MENU
(page 36)
TV/VCR
REC
CODE SET
WIDE MODE
TV/VIDEO
ANT
CODE SET
(pages 54,
56)
1
2
3
4
5
6
MTS
(page 37)
7
8
9
ANT
1
2
3
4
5
6
7
8
9
JUMP
FUNCTION
(pages 26, 56)
Names of the buttons on the remote
control are presented in different
colors to represent the available
functions.
PIP/P&P/
CHANNEL INDEX
(pages 30 - 34)
Button color
TV/VIDEO
(page 27)
ANT
(page 26)
0-9 buttons
(page 26)
ENTER
0
MENU
VOL
DVD MENU
Green:Buttons relevant to power
operations, like turning the
projection TV, SAT/CABLE, or
VCR/MDP/DVD Player on or
off
Label color
CH +/–
(page 26)
White:TV/VCR/MDP/DVD
Player/SAT/CABLE operation
buttons
Yellow:PIP, P&P, and CHANNEL
INDEX operation buttons
RESET
RESET
(pages 37, 38)
Black:Press to select the
component you want to control;
e.g. VCR/MDP/DVD Player,
SAT/CABLE, or projection TV.
ENTER
(pages 26, 54)
CH
VOL +/–
(page 26)
TITLE
MTS
TV/VIDEO
Getting to know the
buttons on the remote
control
TV
SLEEP
VCR/DVD/
MDP
operation
buttons
(page 55)
WIDE MODE
TV
FUNCTION
DVD/VCR SAT/CABLE
PICTURE
MODE
POWER
(pages 26, 56)
TV
FREEZE
AUDIO
TV/SAT
CC
GUIDE/[CC]
(pages 27, 56)
TV
masterpage:Remocon
Joystick
(page 23)
Blue:SAT operation buttons
Pink:DVD Player operation
buttons
TV
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\01COVTOC.fm
Table of Contents
Before You Begin
Welcome! . . . . . . . . . . . . . . . . . . . . . . . . 1
Using this Manual . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safeguards . . . . . . . . . . . . . . 3
Installing and Connecting
the Projection TV
Carrying Your Projection TV. . . . . . . . . . . . . 6
Installing the Projection TV . . . . . . . . . . . . . . 6
Mounting the Rear Speakers (not supplied). . 6
Connector Types . . . . . . . . . . . . . . . . . . . . . . 7
Making Connections . . . . . . . . . . . . . . . . . . . 8
Connecting Directly to a Cable or an
Antenna . . . . . . . . . . . . . . . . . . . . . . 8
Connecting a Cable Box . . . . . . . . . . . 9
Connecting an Antenna/Cable TV
System to a VCR . . . . . . . . . . . . . . 10
Connecting a VCR and Projection TV to
a Cable Box . . . . . . . . . . . . . . . . . . 11
Connecting a DTV (Digital Television)
Receiver . . . . . . . . . . . . . . . . . . . . . 12
Connecting a Satellite Receiver
(SAT) . . . . . . . . . . . . . . . . . . . . . . . 14
masterpage:Left
Connecting a Satellite Receiver
(SAT) and VCR . . . . . . . . . . . . . . . 15
Connecting a Camcorder . . . . . . . . . . 16
Connecting Two VCRs for Tape
Editing . . . . . . . . . . . . . . . . . . . . . . 17
Connecting a DVD Player With S Video
or Composite Video Output
Connectors . . . . . . . . . . . . . . . . . . . 18
Connecting a DVD Player With
Component Video Output
Connectors . . . . . . . . . . . . . . . . . . . 19
Connecting an AV Receiver . . . . . . . 20
Connecting an Audio System . . . . . . . 21
Connecting an Amplifier That Supports
Dolby Pro Logic Decoder . . . . . . . 22
Basic Set Up
Using the Remote Control. . . . . . . . . . . . . . . 23
Setting Up the Projection TV Automatically 24
Adjusting the Convergence Automatically
(FLASH FOCUS) . . . . . . . . . . . . . . . . . . . 25
Using Your New Projection
TV
Watching the TV. . . . . . . . . . . . . . . . . . . . . . 26
Watching Digital TV. . . . . . . . . . . . . . . . . . . 28
Watching the Picture in Wide Screen Mode
Automatically — AUTO WIDE . . . . . . . . 28
Watching the Picture in Wide Screen Mode
Manually — WIDE MODE . . . . . . . . . . .
Watching Two Programs at One Time
— PIP. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watching Two Programs at One Time
— P&P (Twin View™) . . . . . . . . . . . . . .
Using CHANNEL INDEX . . . . . . . . . . . . .
29
30
32
33
Adjusting Your SET UP
(menus)
Learning Menu Selection. . . . . . . . . . . . . . .
Using the VIDEO Menu . . . . . . . . . . . .
Using the AUDIO Menu . . . . . . . . . . . .
Adjusting the Speaker Volume for
Customized Surround Mode . . . . .
Using the TIMER Menu . . . . . . . . . . . .
Using the WIDE SCREEN MODE
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the CHANNEL SET UP Menu . .
Setting and Selecting FAVORITE
CHANNEL . . . . . . . . . . . . . . . . . . . . . . .
Setting FAVORITE CHANNEL
manually . . . . . . . . . . . . . . . . . . . .
Resetting FAVORITE CHANNEL
choices . . . . . . . . . . . . . . . . . . . . .
Using FAVORITE CHANNEL . . . .
Using the SET UP Menu . . . . . . . . . . . .
Using the PARENTAL CONTROL Feature
35
36
37
38
39
40
41
42
43
43
44
44
47
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COVKP57XBRUC\01COVTOCp1.fm
Welcome!
Additional Operations
Thank you for purchasing the Sony Projection TV.
This manual is for models KP-57XBR10W and
KP-65XBR10W.
Operating Video Equipment. . . . . . . . . . . . . 54
Setting the Manufacturer’s Code . . . 54
Operating video equipment . . . . . . . . 55
Operating a Cable Box or Satellite Receiver
(SAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Setting the Manufacturer’s Code . . . 56
Operating a cable box or satellite
receiver . . . . . . . . . . . . . . . . . . . . . 56
Additional Information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . 57
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 60
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
• MID (Multi Image Driver), a newly developed
device, allowing you to enjoy the following features
and, at the same time, to use your projection TV
easily. (not available for input from the VIDEO 5
(DTV) IN jacks)
Model KP-57XBR10W is used for illustration
purposes.
The features you will enjoy include:
• “1080i Capable,” enabling you to receive the 1080i,
720p, 480p and 480i digital TV formats. By using
the VIDEO 5 (DTV) IN jacks, you can connect a
DTV (digital television) receiver to view DTV
programs.
The VIDEO 5 (DTV) IN jacks also function as R/
G/B connectors with SYNC signal (HD/VD), but
are not compatible with a computer’s 5BNC video
output connectors.
— Picture & Picture (P&P) with zoom-in function
(Twin View™)
— Picture-in-Picture (PIP)
— CHANNEL INDEX, allowing you to view and
choose from twelve programs
— FAVORITE CHANNEL, allowing you to view
and choose from eight of your favorite channels
• FLASH FOCUS, allowing you to adjust
convergence automatically.
Before You Begin
Before You Begin
Activating the PARENTAL CONTROL
feature . . . . . . . . . . . . . . . . . . . . . . 47
Selecting a Custom Rating . . . . . . . . 49
Changing the Password . . . . . . . . . . . 51
What the Ratings Mean . . . . . . . . . . . . . . . . 52
• Two Y/PB/PR inputs for DVD Player connection
(480p format capability is on the VIDEO 5 (DTV)
IN jacks).
• Four AUDIO/VIDEO/S VIDEO inputs.
• WIDE SCREEN MODE, allowing you to watch 4:3
normal broadcasts in wide screen mode (16:9 aspect
ratio).
• AUTO WIDE, allowing you to select the wide
screen mode automatically.
• PARENTAL CONTROL, enabling you to block
programs that are unsuitable for your children.
* Manufactured under license from Dolby Laboratories
Licensing Corporation. Additionally licensed under
Canadian patent number 1,037,877. “Dolby,” the double-D
symbol ; and “Pro Logic” are trademarks of Dolby
Laboratories Licensing Corporation
• DRC (Digital Reality Creation), a technology
unique to Sony, allowing you to obtain a finer, more
detailed picture with four-times higher density than
the conventional NTSC picture. (not available for
input from the VIDEO 5 (DTV) IN jacks)
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
1
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\04WEL.fm
Using this Manual
Precautions
We recommend that you carefully review the
contents of the following four sections in the order
provided to ensure that you fully understand the
operation of your new projection TV.
Safety
1 Installing and Connecting the Projection TV
This section guides you through your initial set
up. It shows you how to install your projection
TV, to connect your new components and to
connect to the antenna and cable.
2 Basic Setup
This section teaches you the basic skills needed
to operate your new projection TV, including
Easy Set Up. It shows you how to operate the
remote control’s special functions.
3 Using Your New Projection TV
This section shows you how to begin using
your new projection TV. It shows you how to
use your remote control’s features.
4 Adjusting Your Set Up (menus)
This section teaches you how to access onscreen menus and adjust your projection TV’s
settings.
Instructions in this manual are written for the remote
control. Similar controls may be found on the
projection TV console.
masterpage:Left
Installing
• To prevent internal heat buildup, do not block the
ventilation openings.
• Operate the projection TV only on 120 V AC.
• The plug is designed, for safety purposes, to fit into
the wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact your
dealer.
• If any liquid or solid object should fall inside the
cabinet, unplug the projection TV immediately and
have it checked by qualified service personnel
before operating it further.
• If you will not be using the projection TV for
several days, disconnect the power by pulling the
plug itself. Never pull on the cord.
For details concerning safety precautions, see
“Important Safeguards” on page 3.
Note on cleaning
Clean the cabinet of the projection TV with a dry
soft cloth. To remove dust from the screen, wipe it
gently with a soft cloth. Stubborn stains may be
removed with a cloth slightly dampened with
solution of mild soap and warm water. Never use
strong solvents such as thinner or benzine for
cleaning.
• Do not install the projection TV in a hot or humid
place, or in a place subject to excessive dust or
mechanical vibration.
• Avoid operating the projection TV at temperature
below 5°C (41°F).
• If the projection TV is transported directly from a
cold to a warm location, or if the room temperature
changes suddenly, the picture may be blurred or
show poor color. In this case, please wait a few
hours to let the moisture evaporate before turning
on the projection TV.
• To obtain the best picture, do not expose the screen
to direct illumination or direct sunlight. It is
recommended to use spot lighting directed down
from the ceiling or to cover the windows that face
the screen with opaque drapery. It is desirable to
install the projection TV in a room where the floor
and walls are not of a reflective material.
If the picture becomes dark after using the
projection TV for a long period of time, it may be
necessary to clean the inside of the projection TV.
Consult qualified service personnel.
2
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\04WEL.fm
For your protection, please read these instructions
completely, and keep this manual for future
reference.
Carefully observe and comply with all warnings,
cautions and instructions placed on the set, or
described in the operating instructions or service
manual.
WARNING
To guard against injury, the following basic safety
precautions should be observed in the installation,
use, and servicing of the set.
Use
Power Sources
This set should be operated
only from the type of power
source indicated on the
serial/model plate.
If you are not sure of the
type of electrical power
supplied to your home, consult your dealer or local
power company. For those sets designed to operate
from battery power, refer to the operating
instructions.
Grounding or Polarization
This set is equipped with a polarized AC power
cord plug (a plug having one blade wider than the
other), or with a three-wire grounding type plug (a
plug having a third pin for grounding).
Follow the instructions below:
For the set with a
polarized AC power
cord plug
This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact
your electrician to have a suitable outlet installed.
Do not defeat the safety purpose of the polarized
plug by forcing it in.
Alternate Warning
For the set with a
three-wire grounding
type AC plug
This plug will only fit into a grounding-type power
outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your
electrician to have a suitable outlet installed. Do
not defeat the safety purpose of the grounding
plug.
Overloading
Do not overload wall outlets,
extension cords or
convenience receptacles
beyond their capacity, since
this can result in fire or
electric shock.
Always turn the set off when
it is not to be used. When the
set is left unattended and
unused for long periods of
time, unplug it from the wall
outlet as a precaution against
the possibility of an internal malfunction that
could create a fire hazard.
Before You Begin
Important Safeguards
masterpage:Right
Object and Liquid
Entry
Never push objects of any
kind into the set through the
cabinet slots as they may
touch dangerous voltage
points or short out parts that
could result in a fire or
electric shock. Never spill
liquid of any kind on the set.
Attachments
Do not use attachments not
recommended by the
manufacturer, as they may
cause hazards.
Cleaning
Unplug the set from the wall
outlet before cleaning or
polishing it. Do not use
liquid cleaners or aerosol
cleaners. Use a cloth lightly
dampened with water for
cleaning the exterior of the
set.
(continued)
3
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\04WEL.fm
If a snapping or popping
sound from a projection TV
set is continuous or frequent
while the projection TV is
operating, unplug the
projection TV and consult
your dealer or service
technician. It is normal for
some projection TV sets to
make occasional snapping or popping sounds,
particularly when being turned on or off.
Installation
Water and Moisture
Do not use power-line
operated sets near water—
for example, near a bathtub,
washbowl, kitchen sink, or
laundry tub, in a wet
basement or near a
swimming pool, etc.
4
Accessories
Do not place the set on an
unstable cart, stand, table or
shelf. The set may fall,
causing serious injury to a
child or an adult, and
serious damage to the set.
Use only a cart or stand
recommended by the
manufacturer for the
specific model of projection
TV.
masterpage:Left
An appliance and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may cause
the appliance and cart
combination to overturn.
Ventilation
The slots and openings in the cabinet and in the
back or bottom are provided for necessary
ventilation. To ensure reliable operation of the set,
and to protect it from overheating, these slots and
openings must never be blocked or covered.
- Never cover the slots and
openings with a cloth or
other materials.
- Never block the slots and
openings by placing the set
on a bed, sofa, rug or other
similar surface.
- Never place the set in a
confined space, such as a
bookcase, or built-in cabinet
unless proper ventilation is
provided.
- Do not place the set near or
over a radiator or heat
register, or where it is
exposed to direct sunlight.
Power-Cord Protection
Do not allow anything to rest
on or roll over the power
cord, and do not place the set
where the power cord is
subject to wear or abuse.
Antennas
Outdoor Antenna Grounding — If an
outdoor antenna is installed, follow the precautions
below.
An outdoor antenna system should not be located
in the vicinity of overhead power lines or other
electric light or power circuits, or where it can
come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR
ANTENNA SYSTEM, EXTREME CARE
SHOULD BE TAKEN TO KEEP FROM
CONTACTING SUCH POWER LINES OR
CIRCUITS AS CONTACT WITH THEM IS
ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so as to
provide some protection against voltage surges and
built-up static charges.
Section 810 of the National Electrical Code (NEC)
in USA and Section 54 of the Canadian Electrical
Code in Canada provides information with respect
to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode.
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\04WEL.fm
Ground clamp
Electric service
equipment
NEC: National
Electrical Code
Antenna lead-in
wire
Antenna discharge
unit (NEC Section
810-20)
Grounding
conductors (NEC
Section 810-21)
Ground clamps
Power service
grounding electrode
system (NEC Art 250
Part H)
Lightning
For added protection for this television receiver
during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna. This will prevent damage to the receiver
due to lightning and power-line surges.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
- When the power cord or
plug is damaged or frayed.
- If liquid has been spilled
into the set.
- If the set has been exposed
to rain or water.
- If the set has been subject
to excessive shock by being
dropped, or the cabinet has
been damaged.
- If the set does not operate
normally when following the
operating instructions.
Adjust only those controls
that are specified in the
operating instructions.
Improper adjustment of other controls may result
in damage and will often require extensive work by
a qualified technician to restore the set to normal
operation.
- When the set exhibits a distinct change in
performance—this indicates a need for service.
Servicing
Do not attempt to service the
set yourself since opening
the cabinet may expose you
to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
Replacement Parts
When replacement parts are required, be sure the
service technician certifies in writing that he has
used replacement parts specified by the
manufacturer that have the same characteristics as
the original parts.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
Before You Begin
Antenna Grounding According to the
NEC — Refer to section 54-300 of Canadian
Electrical Code for Antenna Grounding.
masterpage:Right
Safety Check
Upon completion of any
service or repairs to the set,
ask the service technician to
perform routine safety
checks (as specified by the
manufacturer) to determine
that the set is in safe
operating condition, and to
so certify.
When the set reaches the end
of its useful life, improper
disposal could result in a
picture tube implosion. Ask
a qualified service technician
to dispose of the set.
5
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\05INT.fm
Installing and Connecting
the Projection TV
Carrying Your
Projection TV
masterpage:First-Left
REAR SPEAKER OUT R to the terminal on the
other one.
Recommended viewing area
(Vertical)
Note:
min
. 2.4
m(
ap
65" prox. 8
min
ft.)
. 2.1
m(
app
57" rox. 7
ft.)
• When you use a speaker other than one that we
recommend, use a speaker with maximum input
power of more than 20 W and impedance of 8
ohms.
(Rear of projection TV)
Carrying the projection TV requires three or more
people.
The projection TV has been equipped with casters
for easy movement on a hard surface. Please move
your projection TV using the casters.
REAR SPEAKER OUT(MIN 8 )
20˚
20˚
L
L
R
R
Speaker cord
(not supplied)
Installing the
Projection TV
Recommended viewing area
(Horizontal)
mi
n.
mi
2.4
n.
m
2.1
(ap
m
(ap
65 prox
"
p
57 ro
.8
"
ft.
x.
)
7f
t
.)
60˚
60˚
6
Mounting the Rear
Speakers (not
supplied)
For enhanced surround effect, connect the rear
speakers to your projection TV.
Speaker
SS-MB115
(not supplied) etc.
Speaker
SS-MB115
(not supplied) etc.
Connecting the rear speakers
Using the speaker cords, connect REAR
SPEAKER OUT L on your projection TV to the
speaker terminal on one rear speaker, and connect
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\05INT.fm
Component video cable for a DTV
receiver
Connector Types
You may find it necessary to use some of the
following connector types during set up.
• on a wall, as high as the listener’s ears.
• on a table, as high as the listener’s ears.
Coaxial cable
Standard TV cable and antenna cable
Plug Type
Push into connection.
Projection TV
Rear speaker
Screw-on Type
Screw into connection.
S Video cable
High quality video cable for enhanced picture
quality
(Rear of projection TV)
Align guides and
push into connection.
Push into connection.
Installing and Connecting the Projection TV
Installation
For optimum surround effect, mount the rear
speakers in the following places (as shown in the
illustration):
masterpage:Right
G/Y - Green
B/PB - Blue
R/PR - Red
HD - Gray
VD - Black
CONTROL S cable
Sony cable for CONTROL S connections. These
features are exclusive to Sony products and allow
greater control of all Sony equipment.
Push into connection.
(continued)
Audio/Video cable
Push into connection.
Left rear
speaker
Right rear
speaker
Video - Yellow
Audio (Left) - White
Audio (Right) - Red
Some DVD Players are equipped with the
following three video connectors.
Y - Green
PB (CB, Cb or B–Y) - Blue
PR (CR, Cr or R–Y) - Red
7
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\05INT.fm
About the CONTROL S IN/OUT
jacks
Making Connections
To control other Sony equipment with the
projection TV’s remote control, connect the
CONTROL S IN jack of the equipment to the
CONTROL S OUT jack on the projection TV with
the CONTROL S cable.
To control the projection TV with a remote control
for another Sony product, connect the CONTROL
S OUT jack of the equipment to the CONTROL S
IN jack on the projection TV with the CONTROL
S cable.
Connecting Directly to a Cable
or an Antenna
The connection you choose will depend on the
cable found in your home. Newer homes will be
equipped with standard coaxial cable (see A);
older homes will probably have 300-ohm twin lead
cable (see B); still other homes may contain both
(see C).
A
CONTROL S
IN
masterpage:Left
OUT
AUX
CONTROL S
IN
OUT
VIDEO 4
IN
VIDEO 5 (DTV)
HD
OUT
SELECT
VD
IN
VIDEO 1
75-ohm
coaxial cable
(Rear of
projection TV)
VHF/UHF
VIDEO 3
S VIDEO
VHF/UHF
Y
B
Y/G
VIDEO
VIDEO
L
PB
PB/B
PR
PR/R
(MONO)
L
L
(MONO)
AUDIO
• VHF only
or
• VHF/UHF
or
• Cable
R
R
AUDIO
R
COMPONENT
AUDIO
(Rear of
projection TV)
300-ohm twin
VHF/UHF
• VHF only lead cable
or
• UHF only
or
• VHF/UHF
Antenna connector
C
• VHF
75-ohm coaxial cable
(Rear of
projection TV)
VHF/UHF
and
• UHF
EAC-66 U/V mixer
(not supplied)
300-ohm twin lead cable
Cable or antenna
This is the simplest connection. Connection is
made directly from the cable or antenna to the
projection TV.
Cable
(Rear of projection TV)
VHF/UHF
Cable and antenna
You may find it convenient to use the following set
up if your cable provider does not feature local
channels that you are able to receive using an
antenna.
CATV cable
Antenna cable
(Rear of
projection TV)
AUX
VHF/UHF
Select Cable or ANT mode by pressing ANT on
the remote control.
8
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\05INT.fm
Connecting a Cable Box
Also, set CABLE to ON in the CHANNEL SET
UP menu. (see page 41)
(Rear of Projection TV)
VHF/UHF
Cable
For this set up, you can switch between scrambled
channels (through your cable box), and normal
(CATV) channels by pressing ANT on your remote
control.
Installing and Connecting the Projection TV
Some pay cable TV systems use scrambled or
encoded signals that require a cable box* to view
all channels.
masterpage:Right
Notes:
• You may be able to program your Sony remote
control to operate your cable box. (see “Operating a
Cable Box or Satellite Receiver (SAT)” on page 56)
• During PIP, P&P, CHANNEL INDEX or
FAVORITE CHANNEL viewing, the AUX input
can only be viewed in the main picture.
IN
• If you are connecting a cable box through the AUX
input and would like to switch between the AUX
and normal (CATV) input, you should consider
using CHANNEL FIX. (see “CHANNEL FIX” on
page 42)
OUT
*cable box
Note:
• If you will be controlling all channel selection
through your cable box, you should consider using
the CHANNEL FIX feature. (see “CHANNEL
FIX” on page 42)
Cable box and cable
Some pay cable TV systems use scrambled or
encoded signals requiring a cable box* only for
certain channels (e.g. HBO, SHOWTIME, etc.)
*cable box
(Rear of Projection TV)
AUX
VHF/UHF
CATV cable
(unscrambled channels)
9
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
Connecting an Antenna/Cable
TV System to a VCR
masterpage:Left
Disconnect all power sources before making any connections.
1 Attach the coaxial cable from the incoming
(Rear of projection TV)
cable connection or antenna to IN on the VCR.
AUX
CONTROL S
2 Using a coaxial cable, connect OUT on the
IN
VIDEO 4
OUT
IN
VIDEO 5 (DTV)
OUT
SELECT
VCR to VHF/UHF on the projection TV.
HD
3 Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the VCR to
AUDIO and S VIDEO IN on the projection TV
(White-AUDIO Left, Red-AUDIO Right).
VIDEO 3
S VIDEO
2
VHF/UHF
Y
Y/G
PB
PB/B
PR
PR/R
VIDEO
VIDEO
* If your VCR is not equipped with S VIDEO, use
a VIDEO cable (yellow) instead of the S VIDEO
cable.
L
(MONO)
L
AUDIO
R
R
AUDIO
R
COMPONENT
S VIDEO
Coaxial cable
L
(MONO)
Note:
• If you are connecting a monaural VCR, connect
only the single audio output to the left (MONO)
input on the projection TV.
VD
IN
VIDEO 1
AUDIO
VCR
VIDEO
AUDIO-L
AUDIO-R
AUDIO R AUDIO L VIDEO
LINE
IN
1
S VIDEO
VHF/UHF
OUT
LINE
OUT
Cable/
Antenna
IN
VMC-810S/820S
(not supplied)
3
YC-15V/30V (not supplied)
10
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
masterpage:Right
Connecting a VCR and
Projection TV to a Cable Box
Disconnect all power sources before making any connections.
the incoming cable connection, and connect
the other two (output) jacks (using the coaxial
cable) to IN on the cable box and VHF/UHF
on the projection TV.
(Rear of projection TV)
AUX
CONTROL S
2 Using a coaxial cable, connect OUT on the
IN
cable box to IN on the VCR.
IN
VIDEO 5 (DTV)
VIDEO 4
HD
AUDIO and S VIDEO OUT on the VCR to
AUDIO and S VIDEO IN on the projection TV
(White-AUDIO Left, Red-AUDIO Right).
OUT
SELECT
VD
VIDEO 3
S VIDEO
VHF/UHF
Y
Y/G
VIDEO
VIDEO
L
PB
PB/B
(MONO)
PR
PR/R
R
L
L
(MONO)
AUDIO
* If your VCR is not equipped with S VIDEO, use
a VIDEO cable (yellow) instead of the S VIDEO
cable.
Note:
OUT
IN
VIDEO 1
3 Using AUDIO and S VIDEO* cables, connect
• To view scrambled channels through the cable box,
select the video input which the cable box is
connected to by pressing TV/VIDEO.
Installing and Connecting the Projection TV
1 Connect the single (input) jack of the splitter to
R
COMPONENT
S VIDEO
Coaxial cable
AUDIO
R
VIDEO
AUDIO-L
AUDIO-R
AUDIO
VCR
AUDIO R AUDIO L VIDEO
LINE
IN
S VIDEO
VHF/UHF
OUT
LINE
OUT
IN
2
VMC-810S/820S
(not supplied)
3
1
Cable/
Antenna
OUT
IN
Cable box
YC-15V/30V (not supplied)
Splitter
(not supplied)
11
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
masterpage:Left
Connecting a DTV (Digital
Television) Receiver
Disconnect all power sources before making any connections.
Before connecting, be sure to read the Operating
Instructions of the DTV receiver.
2
Connecting a DTV (digital
television) receiver with the Y/PB/
PR (component video input) jacks
1 Attach the coaxial cable from the roof antenna
VMC-10HG
(not supplied)
to VHF/UHF on the DTV receiver.
2 Using three VIDEO cables, connect Y, PB and
PB
PR
PR of COMPONENT VIDEO OUT on the
DTV receiver to Y, PB and PR of VIDEO 5
(DTV) IN on the projection TV.
AUX
CONTROL S
IN
3 Using an AUDIO cable, connect LINE OUT
on the DTV receiver to AUDIO of VIDEO 5
(DTV) IN on the projection TV (WhiteAUDIO Left, Red-AUDIO Right).
Y
OUT
VIDEO 4
HD
to Y PB PR. (see “DTV INPUT” on page 47)
Note:
• Some DTV receiver terminals may be labeled
differently. If so, connect as follows:
Connect Y (green) to Y.
Connect PB (blue) to CB, Cb or B-Y.
Connect PR (red) to CR, Cr or R-Y.
OUT
SELECT
DTV receiver
VD
S VIDEO
IN
VIDEO 1
VIDEO 3
VHF/UHF
(DTV)
S VIDEO
1
VIDEO
PB/B
PR/R
Y
(MONO)
L
1
R
R
2
AUDIO OUT
L
(MONO)
PB
R
L
PB
PR
2
L
(MONO)
Y/G
VIDEO
AUDIO
VIDEO
VHF/UHF
Y
4 Select VIDEO 5 by the TV/VIDEO button.
5 Select the SET UP menu and set DTV INPUT
IN
VIDEO 5 (DTV)
3
PR
VIDEO OUT
AUDIO
R
COMPONENT
AUDIO
1
AUDIO-R
AUDIO-L
Roof Antenna
RK-74A (not supplied)
3
12
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
Connecting a DTV (digital
television) receiver with the G/B/R/
HD/VD jacks
masterpage:Right
Disconnect all power sources before making any connections.
to VHF/UHF on the DTV receiver.
2
2 Using a component video cable for DTV
receiver, connect G, B, R, HD and VD of
VIDEO OUT on the DTV receiver to G, B, R,
HD and VD respectively of VIDEO 5 (DTV)
IN on the projection TV.
If the DTV receiver is equipped with the Y/PB/
PR jacks, proceed to step 2 in “Connecting a
DTV (digital television) receiver with the Y/
PB/PR (component video input) jacks on page
12.
Component video cable for
DTV receiver (not supplied)
HD
VD
G
B
R
IN
OUT
VIDEO 4
IN
VIDEO 5 (DTV)
HD
to R.G.B. (see “DTV INPUT” on page 47)
OUT
SELECT
DTV receiver
S VIDEO
VIDEO 3
VHF/UHF
(DTV)
S VIDEO
VIDEO
1
VHF/UHF
Y
Y/G
PB
PB/B
VIDEO
(MONO)
1
PR/R
R
R
2
AUDIO OUT
L
(MONO)
Y
R
PB
G
HD
PR 4
B
VD
R
L
PR
2
L
(MONO)
L
AUDIO
HD
VD
VD
IN
VIDEO 1
VIDEO
4 Select VIDEO 5 by the TV/VIDEO button.
5 Select the SET UP menu and set DTV INPUT
R
G
B
AUX
CONTROL S
3 Using an AUDIO cable, connect AUDIO OUT
on the DTV receiver to AUDIO of VIDEO 5
(DTV) IN on the projection TV (WhiteAUDIO Left, Red-AUDIO Right).
Installing and Connecting the Projection TV
1 Attach the coaxial cable from the roof antenna
3
VIDEO OUT
AUDIO
R
COMPONENT
AUDIO-R
AUDIO
1
AUDIO-L
Roof Antenna
RK-74A (not supplied)
3
13
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
masterpage:Left
Connecting a Satellite
Receiver (SAT)
Disconnect all power sources before making any connections.
1 Connect the cable from the satellite antenna to
the satellite receiver.
(Rear of projection TV)
2 Attach the coaxial cable from the incoming
cable connection or antenna to VHF/UHF on
the projection TV.
AUX
CONTROL S
IN
3 Using AUDIO and S VIDEO cables, connect
AUDIO and S VIDEO OUT on the satellite
receiver to AUDIO and S VIDEO IN on the
projection TV (White-AUDIO Left, RedAUDIO Right).
VIDEO 4
OUT
IN
VIDEO 5 (DTV)
HD
OUT
SELECT
2
VD
IN
VIDEO 1
Satellite antenna
Cable/
Antenna cable
1
VIDEO 3
S VIDEO
VHF/UHF
Y
Y/G
PB
PB/B
PR
PR/R
VIDEO
VIDEO
L
Note:
• To view input from the satellite receiver, select the
video input which the satellite receiver is connected
to by pressing TV/VIDEO on the remote control.
(MONO)
L
L
(MONO)
AUDIO
R
AUDIO
R
Satellite receiver
R
SATELLITE IN
COMPONENT
VHF/UHF
AUDIO
AUDIO R AUDIO L VIDEO
S VIDEO
IN
OUT
S-VIDEO
AUDIO-L
AUDIO-R
LINE OUT
RK-74A (not supplied)
3
YC-15V/30V (not supplied)
14
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
Connecting a Satellite
Receiver (SAT) and VCR
Disconnect all power sources before making any connections.
AUX
2 Attach the coaxial cable from the incoming
CONTROL S
IN
cable connection or antenna to VHF/UHF IN
on the VCR.
VIDEO 4
OUT
IN
VIDEO 5 (DTV)
OUT
SELECT
SATELLITE IN
VHF/UHF
AUDIO R AUDIO L VIDEO
HD
IN
Satellite
receiver
OUT
LINE OUT
VIDEO 3
S VIDEO
VHF/UHF
Y
1
Y/G
YC-15V/30V
(not
supplied)
VIDEO
VIDEO
Satellite
antenna
cable
L
PB
PB/B
(MONO)
L
L
(MONO)
AUDIO
PR
PR/R
AUDIO
R
R
R
COMPONENT
4
AUDIO
VMC-810S/820S
(not supplied)
VIDEO
AUDIO-L
AUDIO-R
S
VIDEO
S VIDEO
VD
IN
VIDEO 1
3 Using a coaxial cable, connect VHF/UHF
• To view input from the satellite receiver or VCR,
select the video input which your satellite receiver
or VCR is connected to by pressing TV/VIDEO on
the remote control.
3
(Rear of projection TV)
the satellite receiver.
Installing and Connecting the Projection TV
1 Connect the cable from the satellite antenna to
OUT on the VCR to VHF/UHF on the
projection TV.
4 Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the satellite
receiver to AUDIO and S VIDEO IN on the
VCR.
5 Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the VCR to
AUDIO and S VIDEO IN on the projection TV
(White-AUDIO Left, Red-AUDIO Right).
* If your VCR or satellite receiver is not equipped
with S VIDEO, use a VIDEO cable (yellow)
instead of the S VIDEO cable.
Note:
masterpage:Right
VCR
5
AUDIO R AUDIO L VIDEO
LINE
IN
S VIDEO
VHF/UHF
OUT
LINE
OUT
IN
Cable/
Antenna
VMC-810S/820S (not supplied)
2
YC-15V/30V (not supplied)
15
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
masterpage:Left
Connecting a Camcorder
Use this connection to view a picture directly from
your camcorder.
1 Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the camcorder
to AUDIO and S VIDEO IN on the right side
panel inside the drop-down panel on the front
of the projection TV (White-AUDIO Left,
Red-AUDIO Right**).
(Inside the drop down panel on
the Front of projection TV)
TV/VID
EO
–
VOLU
ME
CHAN
NEL
+
–
+
2 Press VIDEO 2 to select the video inputs from
a camcorder.
* If your camcorder is not equipped with S VIDEO,
use a VIDEO cable (yellow) instead of the S
VIDEO cable.
SV
VID
**If you are connecting a monaural camcorder,
connect only the single audio output to the left
(MONO) input on the projection TV.
E
IDE
IN
O2
Push to open.
O
PU
T
EO
VID
L (M
ON
O)
DIO
AU
R
VIDEO
AUDIO-L
AUDIO-R
S VIDEO
YC-15V/30V
(not supplied)
VMC-810S/820S
(not supplied)
Audio/video
outputs
1
1
Camcorder
16
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
Connecting Two VCRs for
Tape Editing
masterpage:Right
Disconnect all power sources before making any connections.
(Rear of projection TV)
AUX
CONTROL S
IN
VIDEO 4
OUT
IN
VIDEO 5 (DTV)
HD
OUT
SELECT
Installing and Connecting the Projection TV
SELECT OUT allows you to use a second VCR to
record a program being played by the primary
VCR or to perform tape editing and dubbing.
VD
IN
VIDEO 1
1 Connect the VCR intended for playback using
the connection instructions on page 10 of this
manual.
S VIDEO
2 Using an AUDIO/VIDEO cable, connect
AUDIO and VIDEO IN on the VCR intended
for recording to AUDIO and VIDEO OUT of
SELECT OUT on the projection TV.
VHF/UHF
PB
PB/B
PR
PR/R
VIDEO
L
(MONO)
L
VCR (for playback)
L
AUDIO
AUDIO
R
R
OUT
AUDIO R AUDIO L VIDEO
VCR (for recording)
R
OUT
AUDIO R AUDIO L VIDEO
COMPONENT
IN
LINE
IN
AUDIO
IN
VIDEO
VIDEO
AUDIO-L AUDIO-L
AUDIO-R AUDIO-R
• Do not change the input signal while editing
through SELECT OUT.
• When the projection TV turns off, the signal is not
output through SELECT OUT.
Y/G
(MONO)
Notes:
• You can select the output signal from SELECT
OUT of the SET UP menu. (see “SELECT OUT”
on page 45)
Y
VIDEO
LINE
OUT
• When connecting a single VCR to the projection
TV: if VCR LINE OUT is connected to VIDEO IN
on the projection TV, do not connect the SELECT
OUT on the projection TV to the VCR LINE
INPUT (see right). Doing so will cause program
interference and other viewing problems.
VIDEO 3
2
1
VMC-810S/820S
(not supplied)
VMC-810S/820S
(not supplied)
(Rear of projection TV)
VIDEO IN
SELECT
OUT
Indicates direction
of signal
IN
LINE
OUT
17
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
masterpage:Left
Connecting a DVD Player With
S Video or Composite Video
Output Connectors
Disconnect all power sources before making any connections.
Using an AUDIO and S VIDEO cables, connect
AUDIO and S VIDEO IN on the projection TV to
AUDIO and S VIDEO OUT on the DVD Player
(White-AUDIO Left, Red-AUDIO Right).
(Rear of projection TV)
AUX
CONTROL S
IN
VIDEO 4
OUT
IN
VIDEO 5 (DTV)
OUT
SELECT
Note:
HD
• Since the high quality pictures on a DVD disc
contain a lot of information, picture noise may
appear. In this case, adjust NR in the VIDEO menu.
(see “NR” on page 37)
VD
IN
VIDEO 1
VIDEO 3
S VIDEO
VHF/UHF
Y
Y/G
PB
PB/B
PR
PR/R
DVD
VIDEO
VIDEO
L
(MONO)
L
L
(MONO)
LINE OUT
R–AUDIO 1–L
AUDIO
R
R
S VIDEO OUT
COMPONENT VIDEO OUT
Y
B-Y
R-Y
DIGITAL OUT
OPTICAL
COAXIAL
R
COMPONENT
S VIDEO
VIDEO
AUDIO
AUDIO
Audio/S video
outputs
AUDIO-L
AUDIO-R
RK-74A (not supplied)
YC-15V/30V (not supplied)
Connect the DVD Player directly
to the projection TV. Connecting
the DVD Player through other
video equipment will cause
unwanted picture noise.
18
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
Connecting a DVD Player With
Component Video Output
Connectors
L of LINE OUT on the DVD Player to AUDIO
R and L of VIDEO 4 IN or VIDEO 5 (DTV)
IN on the projection TV (White-AUDIO Left,
Red-AUDIO Right).
2 Using three VIDEO cables, connect Y, PB and
Disconnect all power sources before making any connections.
You can connect three VIDEO
cables to Y/PB/PR of VIDEO 5
(DTV) IN also.
PR
PB
Y
(Rear of projection TV)
VMC-10HG
(not supplied)
AUX
PR of the COMPONENT VIDEO OUT on the
DVD Player to Y, PB and PR of VIDEO 4 IN or
VIDEO 5 (DTV) IN on the projection TV.
CONTROL S
IN
OUT
VIDEO 4
IN
VIDEO 5 (DTV)
HD
OUT
SELECT
VD
2
IN
VIDEO 1
Notes:
• If your DVD Player has 480p format capability,
connect it to the Y, PB and PR of VIDEO 5 (DTV)
IN on the projection TV.
• Some DVD Player terminals may be labeled
differently. If so, connect as follows:
Connect Y (green) to Y.
Connect PB (blue) to CB, Cb or B-Y.
Connect PR (red) to CR, Cr or R-Y.
• Since the high quality pictures on a DVD disc
contain a lot of information, picture noise may
appear. In this case, adjust NR in the VIDEO menu.
(see “NR” on page 37)
Installing and Connecting the Projection TV
1 Using an AUDIO cable, connect AUDIO R and
masterpage:Right
VIDEO 3
S VIDEO
Y/G
PB
PB/B
PR
PR/R
DVD
VIDEO
VIDEO
L
(MONO)
L
LINE OUT
L
(MONO)
AUDIO
PR
PB
Y
VHF/UHF
Y
R–AUDIO 1–L
R
R
VIDEO
S VIDEO OUT
COMPONENT VIDEO OUT
Y
PB
PR
DIGITAL OUT
OPTICAL
COAXIAL
AUDIO
R
COMPONENT
AUDIO
AUDIO-L
AUDIO-R
1
You can connect an AUDIO
cable to AUDIO R and L of
VIDEO 5 (DTV) IN also.
RK-74A (not supplied)
Connect the DVD Player directly to
the projection TV. Connecting the
DVD Player through other video
equipment will cause unwanted
picture noise.
19
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
Connecting an AV Receiver
masterpage:Left
Disconnect all power sources before making any connections.
For greater control of all audio and video
equipment, connect an AV receiver.
Coaxial cable
VMC-810S/820S (not supplied)
1-2Perform as described on page 10.
(Rear of projection TV)
3 Using a VIDEO cable, connect VIDEO of
VIDEO 1 IN on the projection TV to
MONITOR OUT on the AV receiver.
IN
6 Select the SET UP menu and set SELECT
OUT to TV OUT. (see “SELECT OUT” on
page 45)
OUT
IN
VIDEO 5 (DTV)
OUT
SELECT
HD
VD
IN
SELECT OUT on the projection TV to VIDEO
2 IN on the AV receiver.
video equipment to the AV receiver.
VIDEO 4
VCR
4 Using an AUDIO/VIDEO cable, connect
5 Using an AUDIO/VIDEO cable, connect the
2
AUX
CONTROL S
VIDEO 1
LINE
IN
VHF/UHF
OUT
S VIDEO
Y
IN
Y/G
VIDEO
VIDEO
L
PB
PB/B
(MONO)
PR
PR/R
R
L
L
(MONO)
AUDIO
LINE
OUT
VHF/UHF
AUDIO
R
4
1
R
COMPONENT
Cable/
Antenna
VMC-810S/
820S (not
supplied)
AUDIO
Note:
• You may want to use CHANNEL FIX to fix your
TV’s input to the AV receiver (VIDEO 1). (see
“CHANNEL FIX” on page 42)
S VIDEO
AUDIO R AUDIO L VIDEO
VIDEO 3
VIDEO
AUDIO-L
AUDIO-R
VIDEO
5
AUDIO/
VIDEO
2 IN
VMC-810S/820S (not supplied)
AUDIO/
VIDEO 1 IN
MONITOR
OUT
3
5
4
6
0
10
7
3
1/u
8
2
9
1
OFF
A
B
A+B
–
+
–
+
–
VMC-10HG (not supplied)
+
STR-V555ES etc.
(not supplied)
AUDIO/
VIDEO 1
OUT
20
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
masterpage:Right
Connecting an Audio System
(Rear of projection TV)
Installing and Connecting the Projection TV
For more dynamic sound, connect an audio system
to the projection TV.
Disconnect all power sources before making any connections.
1 Using an AUDIO cable, connect AUDIO
(VAR) OUT on the projection TV to one of the
unused Line inputs (e.g. Tape-2, AUX1, etc.)
on the stereo (White-AUDIO Left, RedAUDIO Right).
L
L
R
R
2 Set the stereo to the chosen Line input and use
the AUDIO menu to switch the TV’s speakers
off. (see “SPEAKER” on page 38)
AUDIO (VAR) OUT-L
AUDIO OUT
VAR
1
L
AUDIO (VAR)
OUT-R
RK-74A
(not supplied)
Line
input
VOLUME
INPUT SELECTOR
PROTECTION
POWER
EON LINK
TAPE1/DAT
TAPE2/MD
SPEAKERS
A
B
•
•
•
EON LINK
BASS
0
•
OFF
AUX
TONE
SACD/CD
TREBLE
0
•
TUNER
PHONO
BALANCE
TAPE MONITOR
SOURCE DIRECT
•
LOUDNESS
¯ ON ¿ OFF
•
A+B
SUBSONIC
¯ ON ¿ OFF
SOURCE
TAPE1 • • • TAPE2
0
10
PHONES
+10
–10
•
•
•
–10
•
R
+10
LEFT
•
FIX
•
Note:
• You can adjust VOLUME, BASS, TREBLE and
BALANCE through the projection TV on AUDIO
(VAR) OUT only.
RIGHT
Stereo amplifier
21
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\06INT.fm
Connecting an Amplifier That
Supports Dolby Pro Logic
Decoder
masterpage:Left
Disconnect all power sources before making any connections.
(Rear of projection TV)
If you use an amplifier with a Dolby Pro Logic
decoder instead of the projection TV’s audio
system, you can still use the projection TV’s
speaker as a center speaker.
L
L
R
R
1 Using the speaker cords (supplied with the
CENTER IN #
amplifier), connect the speaker terminals on
the amplifier to CENTER SPEAKER IN +/–
on the projection TV.
FIX
OUT on the projection TV to one of the unused
Line inputs (e.g. Tape-2, AUX1, etc.) on the
amplifier (White-AUDIO Left, red-AUDIO
Right).
3 Set the amplifier to the chosen Line input and
use the AUDIO menu to set “SPEAKER” to
“CENTER IN” on the projection TV. (see
“SPEAKER” on page 38)
CENTER IN 3
AUDIO OUT
2 Using an AUDIO cable, connect AUDIO (FIX)
VAR
L
1
R
AUDIO (FIX) OUT-L
AUDIO (FIX) OUT-R
2
RK-74A (not supplied)
Line input
3
Amplifier with Dolby
Pro Logic decoder
Rear
speaker (L)
Front
speaker (L)
Rear
speaker (R)
Front
speaker (R)
22
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\07SET.fm
Basic Set Up
Inserting the batteries
Insert two size AA (R6) batteries (supplied) by
matching the + and – on the batteries to the
diagram inside the remote control’s battery
compartment.
Notes:
• Remove the batteries to avoid damage from
possible battery leakage whenever you anticipate
that the remote control will not be used for an
extended period.
Using the remote control joystick
1
2
3
4
5
6
7
8
9
Move
Adjusting sliders
When menu items present a slider ( or ),
move the joystick up, down, left or right to adjust
the setting.
On-line help/instructions
Several menu windows will provide prompts and
instructions to assist you in navigating through the
different functions.
0
m
Basic Set Up
Using the Remote
Control
masterpage:First-Right
Select
Joystick
The supplied remote control has a joystick which
moves the on-screen selector in eight directions. In
most cases, moving the joystick up, down, left or
right will cause the selector to move in the selected
direction.
In some cases, the selector may move in eight
directions according to the function. Pressing
down on the center of the joystick
will activate
the selected item.
You may also move the joystick right to activate a
selected item. (There are some exceptions to this
option.)
• Handle the remote control with care. Avoid
dropping it, getting it wet, or placing it in direct
sunlight, near a heater or where the humidity is
high.
• Your remote control can be programmed to operate
most video equipment. (see “Operating Video
Equipment” on page 54)
23
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\07SET.fm
Setting Up the
Projection TV
Automatically
masterpage:Left
Using the buttons on the front panel and inside the
drop-down panel on the projection TV:
The screen will change to reflect your choice.
CHANNEL
ENGLISH :
ESPAÑOL :
AUTO SET UP :
[ CH + ]
[ CH – ]
[ VOL – ]
POWER
The AUTO SET UP feature will allow you to set
the on-screen language and set all receivable
channels.
First Please connect
the antenna.
Press [ SET UP ] to exit.
TIMER/
STAND BY
STEREO
4 Press VOLUME – to continue.
The AUTO SET UP feature does not apply for
installations that use a cable box for all channel
selection.
SET UP
FLASH FOCUS
TV/VIDEO
VOLUME CHANNEL
+
–
+
–
VOLUME
You can also set up the projection TV manually. (see
“Using the CHANNEL SET UP Menu” on page 41)
CONTINUE TO
AUTO PROGRAM?
YES: [CH +]
NO : [CH –]
Notes:
• Perform this function during the day, with the
antenna and/or cable properly connected, to
ensure that all available channels will be
broadcasting and receivable.
1 Press POWER to turn on the projection TV.
• Before you perform AUTO SET UP again, make
sure that the input from ANT (not AUX) is
selected by pressing ANT until “AUX” does not
appear next to the channel number.
2 Press SET UP inside the drop-down panel.
5 Press CHANNEL + to preset channels
POWER
automatically.
CHANNEL
• When you perform AUTO PROGRAM, your
CHANNEL FIX and ON/OFF TIMER settings
will be erased.
• When you perform AUTO SET UP, all the
settings in the VIDEO and AUDIO menus are
reset to the factory settings.
The AUTO SET UP screen appears.
SET UP
ENGLISH :
ESPAÑOL :
AUTO SET UP :
[ CH + ]
[ CH – ]
[ VOL – ]
First Please connect
the antenna.
Press [ SET UP ] to exit.
3 Press CHANNEL + to select English,
CHANNEL – to select Spanish.
AUTO PROGRAM
“AUTO PROGRAM” appears and the
projection TV starts scanning and presetting
channels automatically. While scanning, the
received channel will be displayed on the sub
screen. When all the receivable channels are
stored, the lowest numbered channel will be
displayed.
24
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\07SET.fm
Tip z
It is recommended to perform FLASH FOCUS about
30 minutes after the projection TV is first turned on.
The cross pattern appears and FLASH FOCUS
begins to work. The adjustment is completed
when the cross pattern becomes white.
POWER
Basic Set Up
If your projection TV is not
connected to a cable system
If you perform AUTO SET UP, CABLE is set to
ON automatically. After finishing AUTO SET UP,
set CABLE to OFF in the CHANNEL SET UP
menu, then set AUTO PROGRAM to YES to
perform automatic channel presetting. (see
“CABLE” and “AUTO PROGRAM” on page 42)
masterpage:Right
FLASH FOCUS
TIMER/
STAND BY
STEREO
To perform AUTO SET UP again
• Press SET UP inside the drop-down panel on the
projection TV, and perform steps 3-5 on page 24.
• Press CHANNEL + or CHANNEL – to select a
language.
• Press VOLUME – to restore factory settings
(“CONTINUE TO AUTO PROGRAM?” will
appear on the screen. Press CHANNEL + to
execute or CHANNEL – to exit).
• Press SET UP to exit.
Adjusting the
Convergence
Automatically (FLASH
FOCUS)
The projection tube image appears on the screen in
three layers (red, green and blue). If they do not
converge, the color is poor and the picture blurs.
Before you use your projection TV, be sure to
adjust the convergence.
The FLASH FOCUS feature allows you to adjust
the convergence automatically.
SET UP
FLASH FOCUS
VOLUME CHANNEL
TV/VIDEO
+
–
+
–
To obtain an optimum convergence
for Digital TV programs
WIDE
MODE
1
2
3
4
5
6
1 Receive a TV or cable TV program.
2 Press FLASH FOCUS for every wide screen
mode; NORMAL, WIDE ZOOM, ZOOM and
FULL.
FLASH FOCUS
To select the wide screen mode, press WIDE
MODE on the remote control.
The optimum convergence alignment varies with
digital TV formats. Whenever you find that the
picture blurs, press FLASH FOCUS.
Notes:
• You cannot perform any other functions until
FLASH FOCUS has completed its cycle.
• If you perform any other operation while FLASH
FOCUS is in progress, FLASH FOCUS operation is
canceled.
25
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
Using Your New
Projection TV
Watching the TV
Many TV features can be accessed directly
through the remote control. The following will
explain the function of some buttons found on your
remote control.
masterpage:First-Left
Using the white labeled buttons for
projection TV operations
REFER TO THE
ILLUSTRATION OF THE
REMOTE CONTROL ON THE INSIDE FRONT
COVER OF THIS MANUAL AS YOU REVIEW THE
FOLLOWING DESCRIPTIONS
TV (FUNCTION)
CH +/–
Press to scan through the channels (+ up or –
down).
VOL +/–
Press to adjust the volume (+ up or – down).
JUMP
Activates the remote control for use with the
projection TV.
ANT
Press to alternate or jump back and forth between two
channels. The projection TV will jump between the
current channel and the last channel selected using the
0-9 buttons.
— (AUX input)
Press to change between the VHF/UHF input and
the AUX input. (for detailed connection
information, see “Cable and antenna” on page 8 or
“Cable box and cable” on page 9).
TV POWER
MUTING
Press to mute the sound. “MUTING” will appear on
the screen and will dim three seconds later. To restore
sound, press again or press VOL +.
FREEZE
Turns the projection TV on and off. If a video
input indication (e.g., VIDEO 1, VIDEO 2)
appears on the screen, press TV/VIDEO until a
channel number appears.
— (yellow labeled button)
This is useful when you need to copy down
information that appears on the TV’s screen.
Press to freeze the picture.
Press again or press (OFF) to cancel.
0 - 9 and ENTER
Use for direct channel selection. Press 0-9 to select a
channel (for example, to select channel 10, press 1
and 0). The channel will change after 2 seconds, or
you can press ENTER for immediate selection.
If you select TWIN as a FREEZE MODE in the
SET UP menu, you can freeze the desired scene
and display it on the left while viewing the normal
picture on the right. (see “FREEZE MODE” on
page 46)
26
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
Notes:
• The FREEZE button does not function with the
picture from VIDEO 5 (DTV) IN.
• If the frozen picture mode is not canceled for more
than an hour, the normal picture is resumed
automatically.
SLEEP
Cancel by pressing until “SLEEP OFF” appears.
DISPLAY
Press to display the channel number, current time,
channel caption (if set), and MTS mode (if SAP is
selected). The SAP indication disappears and the
other indications dim three seconds later.
To turn the display off, press DISPLAY again.
[CC]
PICTURE MODE
Press repeatedly to scroll through available
displays:
Press PICTURE MODE repeatedly to directly
choose one of five different video modes that best
suits the program you are watching.
Caption Vision
Displayed on the screen if the broadcaster offers
this service. (see “CAPTION VISION” on page
45)
XDS (Extended Data Service)
Displays a network name, program name, program
type, program length, program description, call
letters and time of the show if the broadcaster
offers this service.
No display
“OFF” appears and the display is canceled.
VIVID:
Select for enhanced picture contrast and sharpness.
STANDARD:
Select to display a standard picture for normal
viewing environments.
Using Your New Projection TV
Press repeatedly until the projection TV displays
the approximate time in minutes (30, 60, or 90)
that you want the projection TV to remain on
before shutting off automatically.
masterpage:Right
MOVIE:
Select to display a finely detailed picture for low
light environments.
GAME:
Select to display graphics such as a video game.
TV/VIDEO
Press repeatedly to scroll through available video
inputs:
TV, VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4
and VIDEO 5
If you select SKIP as a VIDEO LABEL in the SET
UP menu, your projection TV will skip the video
input you selected. (see “VIDEO LABEL” on page
46)
PRO (Professional):
Select to display a picture with minimum
enhancements.
When you select each mode, you can also adjust
the picture quality (such as BRIGHTNESS,
COLOR, etc.) to suit your taste.
For details, see “MODE” on page 36.
MTS
Press to scroll through the Multi-channel TV
Sound (MTS) options. (see “MTS” on page 37)
27
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
Watching Digital TV
When you have connected the DTV receiver, you
can enjoy digital TV programs. This projection TV
is capable of receiving the 1080i, 720p, 480p and
480i digital TV formats.
Note:
This projection TV is not capable of displaying a
720p format signal as it is. When the 720p format
signal is received, it is converted into a 480p format
signal.
To view a digital TV program
1 Connect the DTV receiver to VIDEO 5 (DTV)
IN on the projection TV. (for details, see pages
13 and 12)
2 Press TV/VIDEO to select VIDEO 5.
The digital TV format being received is
displayed on the screen for three seconds.
Note:
• You cannot select VIDEO 5 unless a DTV
receiver is connected.
masterpage:Left
3 Select a digital channel on the DTV receiver.
For details, see the Operating Instructions of
the DTV receiver.
4 Adjust the volume on this projection TV.
Tip z
The optimum convergence alignment varies with
digital TV formats. Whenever you find that the picture
blurs, press FLASH FOCUS. (for details, see page 25)
Watching the Picture
in Wide Screen Mode
Automatically — AUTO
WIDE
When a 480i format signal with an ID-1 (16:9
aspect ratio recorded) signal is received, the
projection TV automatically selects wide screen
mode.
Notes:
• When the AUTO WIDE function does not work
correctly due to the quality of signal, select wide
screen mode manually. (see page 29)
• The AUTO WIDE function does not work when the
following signals are received:
- 480i format signal without an ID-1 (aspect ratio
recorded) signal
- 480p format signal
- 720p/1080i format signals (The picture is always
displayed in FULL mode)
Activating the AUTO WIDE function
Set AUTO WIDE in the WIDE SCREEN MODE
menu to ON. (see page 40)
TV/VIDEO
DTV FORMAT : 480p
To deactivate the AUTO WIDE function
Set AUTO WIDE in the WIDE SCREEN MODE
menu to OFF. (see page 40)
28
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
When receiving a normal 4:3 broadcast –
NORMAL
When a normal 4:3 aspect ratio picture with an ID1 signal is received, NORMAL mode is
automatically selected. The picture is not enlarged
and is displayed as it is.
Tip z
Watching the Picture in
Wide Screen Mode
Manually — WIDE MODE
You can select the wide screen mode manually.
Note:
The 720p/1080i format signal is displayed in FULL
mode always.
Press WIDE MODE repeatedly on the remote
control.
WIDE MODE
When enlarging the picture to fill the 16:9 screen,
select WIDE ZOOM in WIDE SCREEN MODE menu
manually. (see “Using WIDE ZOOM mode” on this
page)
,
FULL
Note:
• The 720p/1080i format signal is displayed in FULL
mode always.
- video input signals are changed (see “TV/VIDEO”
on page 27)
- the projection TV is turned off
- DIRECT PLAY is selected (see page 46)
- ON/OFF TIMER works (see page 40)
- AUTO WIDE in WIDE SCREEN MODE menu is
set to ON again (see page 40).
Using WIDE ZOOM mode
You can enlarge a normal 4:3 picture of 480i
format signal by selecting WIDE ZOOM.
The picture is enlarged, while the upper and lower
parts of the picture are condensed to fit the 16:9
screen.
Each press scrolls through the following modes:
,
When receiving a 4:3 squeezed picture –
FULL
When a squeezed video camera or DVD picture
with an ID-1 signal is received, FULL mode is
automatically selected.
The picture is enlarged horizontally only, to fill the
16:9 screen.
AUTO WIDE function works again when:
Using Your New Projection TV
,
NORMAL
masterpage:Right
WIDE
ZOOM
For details on each mode, see “To select the wide
screen mode automatically – WIDE MODE.”
When selecting the wide screen mode
manually – Temporarily Auto Wide Off
When the wide screen mode is selected by pressing
the WIDE MODE button on the remote control,
the AUTO WIDE function does not work
temporarily. However, the settings of AUTO
WIDE in WIDE SCREEN MODE menu remains.
Using ZOOM mode
You can enlarge a letter box movie (16:9 aspect
ratio) of a video tape or a DVD disc by selecting
ZOOM.
The picture is enlarged horizontally and vertically
to an equal aspect ratio that fills the 16:9 screen.
,
ZOOM
29
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
Caution about continued wide screen
mode usage for 4:3 aspect ratio pictures
This projection TV was designed primarily for
viewing TV broadcasts in wide screen mode (16:9
aspect ratio pictures). Consistent and exclusive
viewing of 4:3 aspect ratio programs in NORMAL
mode will lead to permanent imprinting of the
gray band on both sides of the picture.
Therefore, when you watch conventional 4:3 ratio
TV programs, we recommend you select WIDE
ZOOM mode by using WIDE MODE button.
Notes:
• Depending on the picture format, black bands may
be present on the top and bottom of the screen.
• For ZOOM and WIDE ZOOM modes you can
adjust the vertical position of the picture. (see “V
CENTER” on page 41)
Watching Two
Programs at One Time
— PIP
The Picture-in-Picture (PIP) feature allows you to
view two channels simultaneously, one in the full
size “main” picture and one in a smaller “window”
picture.
You can move the window picture to any location
on the screen.
Using the yellow labeled buttons
for PIP operations
REFER TO THE
ILLUSTRATION OF THE
REMOTE CONTROL ON THE INSIDE FRONT
COVER OF THIS MANUAL AS YOU REVIEW THE
FOLLOWING DESCRIPTION
Tip z
If you press RESET in PIP mode, the window picture
will move to the bottom right (factory-preset
location).
Note:
• The PIP feature is not available for the inputs
from VIDEO 5 (DTV) IN.
The symbol “9”
indicates which
picture’s sound is
being received.
TV channel or
input-source
mode for the
6
main picture (It
will dim in
about 3
10
seconds.)
TV channel or
input-source
mode for the
Window picture
window picture
(It will dim in
about 3
seconds.)
The symbol “b” or
“B” indicates which
picture’s TV channel
or input source can
be changed.
Main
picture
30
masterpage:Left
Press to display a window picture.
Each time you press this button, the picture size
will change (1/4 t 1/9 t 1/16).
Press (OFF) to close the window picture.
POSITION
Press to change the location of the window picture
(counterclockwise) around the main picture.
ACTIVE
Press to select either the main or window picture in
order to change the TV channel or video source
using the white labeled buttons below. The symbol
“b” (or “B”) will appear to indicate which
picture’s channel or input mode can be changed.
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
— (white labeled button)
To change the location of the window picture,
move the joystick in any direction and release it
when the picture is in the desired location.
TV/VIDEO
— (white labeled button)
CH
or
0 - 9 or
JUMP
and ENTER
— (white labeled button)
Press to select the TV channel on which the
symbol “b” (or “B”) is displayed. (for details, see
“Watching the TV” on page 26)
AUDIO
OFF
Press to alternate sound between the main picture
and the window picture. The symbol “9” will
appear for a few seconds to indicate which
picture’s sound is being received.
FREEZE
This is useful when you need to copy down
information that appears on the TV’s screen.
Press to freeze the main and window pictures.
Press to cancel the PIP function and return to
normal viewing.
Notes:
• If one of the pictures received through PIP is snowy,
the entire screen may become unstable. In this case,
erase the snowy channel. (see “CHANNEL SKIP”
on page 41)
Using Your New Projection TV
Press repeatedly to scroll through the available
video inputs for the picture on which the symbol
“b” (or “B”) is displayed. (see “TV/VIDEO” on
page 27)
masterpage:Right
• If you select VIDEO 5 when the main picture is
active, the window picture disappears and you
can view the picture from VIDEO 5 (DTV) IN.
When the window picture is active, you cannot view
the picture from VIDEO 5 (DTV) IN.
Press again to resume PIP viewing. Press (OFF)
to cancel and resume normal TV viewing.
SWAP
Press to switch the audio and video of the main
picture and the window picture.
Each time you press SWAP, the picture and sound
of the two will be exchanged.
ANT — (white labeled button)
Press to change between the VHF/UHF input and
the AUX input for the picture on which the symbol
“b” (or “B”) is displayed.
Press to access CHANNEL INDEX for direct
channel selection. (see “Using CHANNEL
INDEX” on page 33)
31
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
Watching Two
Programs at One Time
— P&P (Twin View™)
The Picture-and-Picture (P&P) feature allows you
to view two channels simultaneously, both in a
reduced size screen. The main picture will appear
on the right.
You can change the size of both pictures to suit
your personal preference.
masterpage:Left
Using the yellow labeled buttons
for P&P operations
Moving the joystick right or left will activate the
same function.
REFER TO THE
ILLUSTRATION OF THE
REMOTE CONTROL ON THE INSIDE FRONT
COVER OF THIS MANUAL AS YOU REVIEW THE
FOLLOWING DESCRIPTIONS
LEFT
Tip z
If you press RESET in P&P mode, the right and left
pictures will be reset to the same size (factory-preset
size.)
RIGHT
Note:
• The P&P feature is not available for the inputs
from VIDEO 5 (DTV) IN.
Press to display right (main) and left pictures.
Press (OFF) to close the sub picture.
The symbol “b”
or “B” indicates
TV channel which picture’s
or inputTV channel or
source
input source can
mode for the be changed.
sub picture
(It will dim in
about 3
seconds.)
7
Sub
picture
6
The symbol
“9” indicates
which
picture’s
sound is
being
received.
TV channel or
input-source
mode for the
main picture (It
will dim in
about 3
seconds.)
Main picture
ZOOM IN
LEFT
RIGHT
ACTIVE
or
— (white labeled button)
Press and hold either RIGHT or LEFT to zoom in
on the selected picture.
Release at the desired size. The other picture will
be zoomed out simultaneously.
Press to select either the right or left picture in
order to change the TV channel or video source
using the white labeled buttons below. The symbol
“b” (or “B”) will appear to indicate which
picture’s channel or input mode can be changed.
TV/VIDEO — (white labeled button)
Press repeatedly to scroll through the available
video inputs for the picture on which the symbol
“b” (or “B”) is displayed. (see “TV/VIDEO” on
page 27)
32
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
masterpage:Right
SWAP
CH
or 0 - 9 or JUMP
and ENTER
— (white labeled button)
ANT — (white labeled button)
Press to change between the VHF/UHF input and
the AUX input for the picture on which the symbol
“b” (or “B”) is displayed.
Press to switch the audio and video of the right and
left pictures.
Each time you press SWAP, the picture and sound
of the two will be exchanged.
OFF
Press to cancel the P&P function and return to
normal viewing.
Notes:
• If one of the pictures received through P&P is
snowy, the entire screen may become unstable. In
this case, erase the snowy channel. (see
“CHANNEL SKIP” on page 41)
• The CHANNEL INDEX feature is not available
for the inputs from VIDEO 5 (DTV) IN.
1 Press
.
The current channel will be reduced in size and
displayed in the center of the screen in normal
motion picture format. The first twelve
receivable channels will appear one after
another, clockwise, around the center picture.
These small pictures are updated in intervals of
one second. The channel number and channel
caption (if set) on the second and later
appearances will dim.
Using Your New Projection TV
Press to select the TV channel on which the
symbol “b” (or “B”) is displayed. (for details, see
“Watching the TV” on page 26)
Note:
10
AUDIO
Press to alternate sound between the right and left
pictures. The symbol “9” will appear for a few
seconds to indicate which picture’s sound is being
received.
FREEZE
This is useful when you need to copy down
information that appears on the TV’s screen.
Press to freeze both the right and left pictures.
Press again to resume P&P viewing or press
(OFF) to cancel and resume normal TV viewing.
• If you select VIDEO 5 when the right picture is
active, the left picture disappears and you can view
the picture from VIDEO 5 (DTV) IN. When the left
picture is active, you cannot view the picture from
VIDEO 5 (DTV) IN.
A cyan-colored frame will appear to indicate
current channel selection.
2 Move the joystick in any direction to move the
Using CHANNEL
INDEX
cyan frame to the picture that you wish to view,
and press .
You can use the CHANNEL INDEX feature to
display multiple channels and select one directly.
Reciipe
flour - - - - 2
s u g a r - - - 1/2
s a l t - - - - - 1/2
butter - - - 1
Channels used for CHANNEL INDEX will come
directly from the TV’s list of receivable channels
(those set during AUTO PROGRAM or through
the CHANNEL SET UP menu).
(continued)
33
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\08CTV.fm
The selected channel will zoom in and move to
the center, and the sound of that channel will
be heard.
Reciipe
flour - - - - 2
s u g a r - - - 1/2
s a l t - - - - - 1/2
butter - - - 1
3 If you wish to view another channel, repeat
step 2.
To view the normal picture of the selected
channel, proceed to step 4.
masterpage:Left
• If you leave the CHANNEL INDEX screen
displayed for an hour without any additional
operation, CHANNEL INDEX is canceled and the
normal picture reappears.
Using the yellow labeled buttons
for CHANNEL INDEX operations
REFER TO THE
ILLUSTRATION OF THE
REMOTE CONTROL ON THE INSIDE FRONT
COVER OF THIS MANUAL AS YOU REVIEW THE
FOLLOWING DESCRIPTIONS
REFER TO THE
ILLUSTRATION OF THE
REMOTE CONTROL ON THE INSIDE FRONT
COVER OF THIS MANUAL AS YOU REVIEW THE
FOLLOWING DESCRIPTIONS
TV/VIDEO
Press to scroll the center picture through the video
inputs.
The surrounding channels will not change.
4 Press
.
The center picture will be enlarged for normal
viewing.
Using the white labeled buttons for
center picture operations
Press to display the next twelve receivable
channels.
ANT
Press to switch the center picture between the
VHF/UHF input and the AUX input.
OFF
Press to cancel the current operation and return to
normal TV viewing.
CH
or
Notes:
• You cannot move the cyan frame until all of the
surrounding pictures appear.
• The projection TV will continually update each of
the surrounding pictures while the CHANNEL
INDEX screen is displayed.
FREEZE
JUMP
0 - 9 or
and ENTER
Press to freeze the center picture.
Press again to cancel the frozen picture and resume
normal center picture viewing.
Press to select a channel for the center picture. (for
details, see “Watching the TV” on page 26)
• Sound will only be heard from the center picture.
34
• If one of the pictures received through CHANNEL
INDEX is snowy, the entire screen may become
unstable. In this case, erase the snowy channel. (see
“CHANNEL SKIP” on page 41)
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
Adjusting Your SET UP
(menus)
3 Move the joystick up or down to highlight the
desired option.
Move
The main menu appears.
MENU
VIDEO
MODE :
PICTURE
BRIGHTNESS
COLOR
HUE
SHARPNESS
COLOR TEMP :
NR :
DYNAMIC PICTURE :
Move
Select
VIVID
COOL
OFF
OFF
Exit
MENU
desired menu and press
(press down on the
center of the joystick) to activate it.
SET UP
PARENTAL CONTROL
CAPTION VISION:
CC1
SELECT OUT: MONITOR
LANGUAGE:
ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE: NORMAL
DTV INPUT:
Y PB PR
Select
MENU
4 Press
(press down on the center of the
joystick).
Options for your selection (Pop-up menu or
Adjusting menu) will be displayed.
Pop-up menu
2 Move the joystick up or down to highlight the
Move
Exit
Exit
SET UP
PARENTAL CONTROL
CAPTION VISION:
CC1
SELECT OUT:
VIDEO1
LANGUAGE:
ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE: NORMAL
DTV INPUT:
Y PB PR
SET UP
PARENTAL CONTROL
CAPTION VISION
CC1
SELECT OUT: MONITOR
LANGUAGE: ENGLISH
VIDEO1
VIDEO LABEL
VIDEO2
DIRECT PLAY
VIDEO3
FREEZE MODE:NORNAL
VIDEO4
DTV INPUT:
R.G.B
TV OUT
OUT
TV
Move
Select
Exit
MENU
Adjusting menu
Move
Select
Exit
MENU
Some adjustment menus may require further
operations. For details, see each menu option.
To return to the previous screen (except for the
slider adjustment menus), choose
at the
bottom of the menu and press
or move the
joystick left.
6 Once you have completed all menu
corrections, press MENU to exit the menu
screens.
MENU
VIDEO LABEL
VIDEO1:
VIDEO2:
VIDEO3:
VIDEO4:
VIDEO5:
Move
Adjusting Your SET UP (menus)
1 Press the MENU button.
Select
5 Move the joystick up or down to make your
selection and press
to activate it.
The previous screen will reappear.
SET UP
PARENTAL CONTROL
CAPTION VISION:
CC1
SELECT OUT: MONITOR
LANGUAGE:
ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE: NORMAL
DTV INPUT:
Y PB PR
Learning Menu
Selection
Use the MENU button to access a menu and use
the joystick to alter the settings. Use the following
example to learn how to modify settings.
masterpage:First-Right
VIDEO1
VIDEO2
VIDEO3
VIDEO4
VIDEO5
Select
Exit
MENU
To exit from the menus at any time
Press MENU.
MENU
You may also move the joystick right to
activate your selection.
35
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
Using the VIDEO
Menu
VIDEO
MODE :
PICTURE
BRIGHTNESS
COLOR
HUE
SHARPNESS
COLOR TEMP :
VIVID
COOL
NR :
DYNAMIC PICTURE :
Move
Select
}
Sliders
OFF
OFF
Exit
MENU
For detailed information on using the remote
control to modify menu settings, refer to “Learning
Menu Selection” on page 35.
To select the VIDEO
Display
,
Highlight
menu:
, Select
MENU
masterpage:Left
VIVID:
Select for enhanced picture contrast and sharpness.
STANDARD:
Select to display a standard picture for normal
viewing environments.
MOVIE:
Select to display a finely detailed picture for low
light environments.
GAME:
Select to display graphics such as a video game.
You can choose one of five different video modes
that best suits the program you are watching. You
can also adjust the picture quality (such as
BRIGHTNESS, COLOR, etc.) for each MODE to
suit your taste.
Adjust slider left (down) to decrease color
intensity.
HUE
— Picture Adjustment
Adjust slider right (up) to increase the green tones.
Adjust slider left (down) to increase the red tones.
— Picture Adjustment
Press PICTURE MODE on the remote control for
direct selection of a MODE setting.
Adjust slider right (up) to sharpen the picture.
Adjust slider left (down) to soften the picture.
COLOR TEMP
— White Intensity (Color Temperature)
Adjustment
PICTURE
— Picture Adjustment
Adjust slider left (down) to decrease picture
contrast.
— Customized picture viewing
— Picture Adjustment
Adjust slider right (up) to increase color intensity.
SHARPNESS
PRO (Professional):
Select to display a picture with minimum
enhancements.
Adjust slider right (up) to increase picture contrast.
MODE
COLOR
BRIGHTNESS
— Picture Adjustment
Adjust slider right (up) to brighten the picture.
Adjust slider left (down) to darken the picture.
COOL:
Select to give the white colors a blueish tint.
NEUTRAL:
Select to give the white colors a neutral tint.
WARM:
Select to give the white colors a reddish tint.
First select each MODE individually before
adjusting the picture quality.
36
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
NR
— Picture Noise Reduction
Select ON to reduce picture noise.
AUDIO
TREBLE
BASS
BALANCE
MTS :
STEREO
SPEAKER :
ALL ON
EFFECT:
OFF
SURROUND LEVEL
NR can be set separately from the MODE settings
of the VIDEO menu.
DYNAMIC PICTURE
— Black Intensity Adjustment
To restore the factory settings
Press RESET on the remote control while the
VIDEO menu is selected. To restore each MODE
to the factory setting, press RESET after selecting
the mode to be reset.
Move
Select
Exit
BALANCE
— Sound Adjustment
} Sliders
Adjust slider right (up) to emphasize right speaker
volume.
Adjust slider left (down) to emphasize left speaker
volume.
MENU
MTS
For detailed information on using the remote
control to modify menu settings, refer to “Learning
Menu Selection” on page 35.
To select the AUDIO
Display
,
Highlight
menu:
, Select
MENU
— Enjoy stereo, bilingual and mono
programs
Adjusting Your SET UP (menus)
Select OFF to cancel the feature.
Adjust slider left (down) to decrease low pitched
sounds.
Using the AUDIO
Menu
Select OFF to cancel the feature.
Select ON to emphasize the black level and to
produce a bolder dynamic picture.
masterpage:Right
STEREO:
Select for stereo reception when viewing a
program broadcast in stereo.
SAP:
Select to listen to a bilingual broadcast. (non-SAP
programs will be muted when this feature is
selected)
MONO:
Select for mono reception. (use to reduce noise
during stereo broadcasts)
TREBLE
— Sound Adjustment
Adjust slider right (up) to increase high pitched
sounds.
Adjust slider left (down) to decrease high pitched
sounds.
BASS
— Sound Adjustment
Adjust slider right (up) to increase low pitched
sounds.
Quick MTS access:
Press MTS on your remote control to cycle through
the MTS options as follows: (STEREO b SAP b
MONO b STEREO).
Note:
• The MTS function is not available for input
from an external equipment connected VIDEO
1, VIDEO 2, VIDEO 3, VIDEO 4 or VIDEO 5
(DTV) IN.
(continued)
37
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
SPEAKER
— Custom selection of audio output source
ALL ON:
Select to listen to the sound from the projection
TV speakers alone.
L/R OFF:
Select to turn off the projection TV left and right
speakers and listen to the left and right channel
sounds through a separate audio system’s speakers.
ALL OFF:
Select to turn off the projection TV speakers and
listen to the projection TV’s sound only through an
external audio system’s speakers.
CENTER IN:
Select to use the projection TV center speaker as
center speaker when you connect an amplifier with
a Dolby Pro Logic decoder. (see “Connecting an
Amplifier That Supports Dolby Pro Logic
Decoder” on page 22)
EFFECT
— Customizes surround sound effects
based on the program’s audio type
EFFECT can only be set when SPEAKER is set to
ALL ON or L/R OFF.
; PRO LOGIC:
Produces superb theater-like surround effects.
Most effective for programs encoded in Dolby
surround.
masterpage:Left
; 3 STEREO:
Produces a dynamic three dimensional sound
without using the rear speakers. The sound of the
rear channel is output from the front speakers.
SRS 3D MONO:
Adds a surround-like effect to mono programs.
LIVE:
Produces surround effects with the atmosphere of a
concert hall.
GAME:
Produces maximum audio impact. Most effective
for video games.
OFF:
Normal stereo or mono reception.
Adjusting the Speaker Volume
for Customized Surround
Mode
After you set EFFECT to one of the modes, adjust
the volume of the front, center and rear speakers to
the same level so that the projection TV’s sound
will be even and natural. For ;PRO LOGIC and
;3 STEREO, adjust the speaker volume using
the test tone feature.
Adjusting the speaker volume
1 Connect the rear speakers (not supplied).
For details, see “Mounting the Rear Speakers
(not supplied)” on pages 6 and 7.
2 Select SURROUND LEVEL from the AUDIO
SURROUND LEVEL
menu. (see “SURROUND LEVEL” on the left
column)
— Speaker volume adjustment for
surround modes
After selecting one of the surround modes, adjust
the volume of each speaker so that the sound will
be even and natural. (see “Adjusting the Speaker
Volume for Customized Surround Mode” on the
right column)
;PRO-LOGIC
CENTER
REAR
BALANCE
TEST TONE :
Move
Select
OFF
Exit
MENU
To restore the factory settings
Press RESET on the remote control while the
AUDIO menu is selected.
However, EFFECT is not reset to the factory
setting even if you press RESET.
38
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
3 Move the joystick up or down to select the
speaker for volume adjustment and press
;PRO-LOGIC
CENTER
REAR
BALANCE
TEST TONE :
.
masterpage:Right
Adjusting the speaker volume
using the test tone
The TEST TONE feature makes it easier to adjust
the volume level. You can use this feature for
;PRO LOGIC and ;3 STEREO modes only.
Using the TIMER
Menu
TIMER
DAYLIGHT SAVING:
CURRENT TIME
ON / OFF TIMER
OFF
1 With the SURROUND LEVEL window open,
Move
Select
Exit
move the joystick up or down to select TEST
TONE and press .
MENU
Move
4 Move the joystick up, down, left or right to
.
5 Use the joystick to select other speakers and to
adjust the volume levels.
;PRO-LOGIC
CENTER
REAR
BALANCE
TEST TONE :
Move
Select
MENU
After setting the clock you can use the timer to
turn the projection TV on and off.
ON
OFF
Exit
––:––AM
Select
Exit
Adjusting Your SET UP (menus)
CENTER: Select to adjust the level of the
center speaker. (not available for SRS 3D
MONO)
REAR: Select to adjust the level of the rear
speakers. (not available for ;3 STEREO)
BALANCE: Select to adjust the balance
between the right and left speakers.
adjust the volume level and press
NO
For detailed information on using the remote
control to modify menu settings, refer to “Learning
Menu Selection” on page 35.
MENU
2 Move the joystick up or down to select ON.
A test tone will be output from each speaker in
sequence:
Front left t Center t Front right t Rear
To select the TIMER
Display
,
Highlight
menu:
, Select
MENU
To turn off the test tone, select OFF.
3 Follow steps 2 through 4 in “Adjusting the
speaker volume.”
Note:
You can adjust the volume using the test tone
independent of the projection TV’s operation.
Tip z
Set daylight saving time before setting the clock. Any
loss of power will cause these settings to be erased.
(continued)
39
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
DAYLIGHT SAVING
ON/OFF TIMER
— Automatically adjusts the time.
— Wake up or scheduled viewing.
Select YES to compensate for Daylight Saving
Time in spring. The current time automatically
moves ahead one hour.
Select NO at the end of Daylight Saving Time in
fall. The current time moves back one hour.
masterpage:Left
1 Select the desired timer
ON / OFF TIMER
(1 or 2).
1. – – – – – –
– – : – – AM – H ch– – –
2 Move the joystick up or
2. – – – –
– – : – – AM – H ch– – –
down until the desired
SUN
1 2 : 0 0AM
day (MON-SUN) or
Move
Select
Exit
range of days (EVERY
SUN-SAT or EVERY MON-FRI) is displayed,
and press .
Using the WIDE
SCREEN MODE Menu
WIDE SCREEN MODE
AUTO WIDE :
ON
WIDE MODE :
ZOOM
V CENTER :
0
MENU
CURRENT TIME
— Necessary for the TIMER.
CURRENT TIME
1 Press , then move the
joystick up or down
– – – – – : – –AM
until the current day
(MON-SUN) is
displayed, and press .
Move
Select
Exit
2 Move the joystick up or
down until the current hour (1-12) and AM/PM
is displayed, and press .
MENU
3 Move the joystick up or down until the current
minute (00-59) is displayed, and press .
The Clock has now started. Press MENU to exit.
Move
Select
Exit
MENU
3 Move the joystick up or down until the time
(hours and minutes) that you want the
projection TV to remain on is displayed, and
then press .
For detailed information on using the remote
control to modify menu settings, refer to “Learning
Menu Selection” on page 35.
4 Move the joystick up or down to set the time
duration (maximum of 6 hours) and press .
5 Move the joystick up or down to select the
desired channel and press .
To select the WIDE SCREEN MODE
menu:
The timer is now set. The TIMER/STAND BY
indicator on your projection TV will be lit.
Press MENU to exit. To cancel your timer setting,
select timer 1 or 2 and press RESET while in the ON/
OFF TIMER window. Performing AUTO PROGRAM
will erase all TIMER settings.
Display
,
Highlight
, Select
MENU
AUTO WIDE
— Automatically selects the wide screen
mode
Select ON to automatically display the picture
with an ID-1 (aspect ratio recorded) signal of 480i
format in an optimum wide screen mode; normal
4:3 picture in NORMAL, letterbox picture in
ZOOM, and 4:3 squeezed picture in FULL. (for
details, see pages 28 and 29)
Select OFF if you want to choose the wide screen
40
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
mode manually by pressing the WIDE MODE
button repeatedly.
WIDE MODE
Using the CHANNEL
SET UP Menu
— Manually selects the wide screen mode
You can select NORMAL, WIDE ZOOM, ZOOM
or FULL for the 4:3 or letterbox picture to fill the
16:9 screen manually by pressing the WIDE
MODE button repeatedly. (for details on each
mode, see “Watching the Picture in Wide Screen
Mode Automatically — AUTO WIDE” on page
28)
— Adjusts the position of the picture
Allows you to move the picture vertically within
the screen (available only in ZOOM and WIDE
ZOOM modes).
Move the joystick up or down to move the picture,
and press .
CHANNEL SET UP
CHANNEL SKIP
CHANNEL CAPTION
CABLE :
ON
AUTO PROGRAM
FAVORITE CHANNEL : AUTO
CHANNEL FIX :
OFF
Move
Select
Exit
MENU
For detailed information on using the remote
control to modify menu settings, refer to “Learning
Menu Selection” on page 35.
,
Highlight
, Select
CHANNEL SKIP
— Skips unnecessary channels
With the CHANNEL SKIP
window open:
— Easy recognition of the channel you are
watching
With the CHANNEL
CAPTION window open:
MENU
After AUTO SET UP, you
can erase unnecessary TV
channels from the channel
preset memory.
CHANNEL CAPTION
You can add a caption for
up to 32 channels of both
VHF/UHF and AUX
inputs.
To select the CHANNEL SET UP
menu:
Display
1 Move the joystick up or down to select the
desired channel. You can view the channel that
is selected with the CHANNEL SKIP menu in
the center sub screen. You can also use CH +/–
or 0–9 and ENTER buttons.
2 Press .
3 Move the joystick up or down to select YES,
and press .
The selected channel will be erased.
If you want to re-enter the skipped channel, follow
the steps above and select NO.
CHANNEL SKIP
1:
2:
3:
4:
5:
6:
7:
8:
Select a channel
Move
Select
NO
NO
NO
NO
NO
NO
NO
NO
Exit
MENU
Adjusting Your SET UP (menus)
V CENTER
masterpage:Right
CHANNEL CAPTION
CHANNEL :
CAPTION :
Move
– ––
– –––
Select
Exit
MENU
1 Press
and then move the joystick up or
down to select the desired channel. You can
view the channel that is selected with the
CHANNEL CAPTION menu in the center sub
screen.
2 Press .
3 Move the joystick up or down to display the
first letter or number of the caption and press
to select it.
4 Repeat until up to four digits are selected.
5 Press .
To erase a caption, press RESET.
(continued)
41
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
masterpage:Left
CABLE
CHANNEL FIX
— Cable system setting
— Locks selection of your projection TV’s
input when used in conjunction with
external equipment such as a cable box, AV
receiver, etc.
Select ON if your projection TV is connected to a
cable system.
Select OFF if your projection TV is connected to
an antenna.
AUTO SET UP will set CABLE to ON
automatically.
AUTO PROGRAM
— Automatic channel presetting
Select YES to signal the projection TV to
automatically program all receivable TV channels.
When all the receivable channels are stored, the
lowest numbered channel is displayed.
Select NO to cancel AUTO PROGRAM.
FAVORITE CHANNEL
— User’s favorite channels
The FAVORITE CHANNEL feature enables easy
access to the eight channels that you preset (or the
last channel that you were watching).
(for details on how to set up this feature, see
“Setting and Selecting FAVORITE CHANNEL”
on this page.)
2-6:
When the cable box is connected to the VHF/UHF
input, you can fix the TV’s input to one of the
channels between 2 and 6. Press SAT/CABLE
(FUNCTION) and then CH +/– to change the
cable box channels.
AUX 2-6:
Use this when a cable box is connected to AUX,
and a cable or antenna is connected to VHF/UHF.
VIDEO 1:
Use this when you have connected external video
equipment (e.g. AV receiver) and you want the
projection TV’s input fixed to it.
OFF:
When you want to switch CHANNEL FIX off.
If the projection TV is in the AUX mode when you
turn CHANNEL FIX off, press ANT to return to
UHF input mode.
Setting and Selecting
FAVORITE CHANNEL
The FAVORITE CHANNEL feature of your
projection TV enables easy access to the eight
channels that you preset (or the last channel that
you were watching).
Your FAVORITE CHANNEL options can be set
automatically or manually.
The factory setting for FAVORITE CHANNEL is
AUTO.
When FAVORITE CHANNEL is set to AUTO, the
last eight channels selected with the 0–9 buttons
will be set as FAVORITE CHANNEL options. If
you want to input your own selections as
FAVORITE CHANNEL settings, set to
MANUAL.
Note:
• You can not use the FAVORITE CHANNEL
when watching the signal input from VIDEO 5
(DTV) IN.
TIMER settings are erased when CHANNEL FIX is
set.
Note:
• You cannot change channels with the TV’s tuner
when you set CHANNEL FIX. If you want to use
the TV’s tuner while fixing the TV’s input to
VIDEO 1, use the SET UP menu to set SELECT
OUT to TV OUT. (see “SELECT OUT” on page
45)
42
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
Setting FAVORITE CHANNEL
manually
3 Move the joystick up or down to select a
position (1–8), and press
1 Select FAVORITE CHANNEL from the
CHANNEL SET UP
CHANNEL SKIP
CHANNEL CAPTION
CABLE :
ON
AUTO PROGRAM
FAVORITE CHANNEL : AUTO
CHANNEL FIX :
MANUAL
Select
Exit
Select a channel
Move
Select
Exit
Simply proceed as described in “Setting
FAVORITE CHANNEL manually” (skip step 2 if
MANUAL is already selected).
MENU
.
channel.
You have now selected a favorite channel.
The FAVORITE CHANNEL menu will appear.
If you set CHANNEL CAPTION names (e.g.
CNN, HBO), they will also be displayed. (see
“CHANNEL CAPTION” on page 41)
FAVORITE CHANNEL
1 CNN
1.
2.
2
3 . 10 SPTN
4 . 22
5 . 30
6 . 40
7 . 52
8 . 125
Select a position
Move
Select
Exit
FAVORITE CHANNEL
1.
1 CNN
2 . 125
3 . 10 SPTN
4 . 22
5 . 30
6 . 40
7 . 52
8 . 125
Select a channel
Move
Select
Exit
FAVORITE CHANNEL
1 . ___
2
2.
3 . 10 SPTN
4 . 22
5 . 30
6 . 40
7 . 52
8 . 125
Select a channel
Move
Select
MENU
5 Press
and use the joystick to program other
favorite channels. (Follow steps 3 and 4.)
6 Press MENU when you have finished.
MENU
When you reach step 3, select the position you
want to change and press . Press RESET to
clear the channel for that position.
Your favorite channels are now ready for use.
Adjusting Your SET UP (menus)
2 Move the joystick up or down to select
Resetting FAVORITE
CHANNEL choices
You have the option of returning to the FAVORITE
CHANNEL screen to adjust any of your favorite
channel choices.
4 Move the joystick up or down to select a
MENU
MANUAL and press
.
FAVORITE CHANNEL
1 CNN
1.
2
2.
3 . 10 SPTN
4 . 22
5 . 30
6 . 40
7 . 52
8 . 125
CHANNEL SET UP menu. (see page 41)
Move
masterpage:Right
Exit
MENU
Move the joystick up or down to select a new
channel.
Press MENU when you are done.
Note:
• The FAVORITE CHANNEL feature is not
available for the picture input from AUX or
VIDEO 5 (DTV) IN.
(continued)
43
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
Using FAVORITE CHANNEL
You can use the FAVORITE CHANNEL feature to
directly select the channel you want to watch.
1 Press
3 Press
masterpage:Left
to select the channel.
The selected channel will be displayed for
normal viewing.
Using the SET UP
Menu
SET UP
PARENTAL CONTROL
CAPTION VISION:
CC1
SELECT OUT:
MONITOR
LANGUAGE:
ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE: NORMAL
Y PB PR
DTV INPUT:
once.
The favorite channel menu and a window
picture will be superimposed over the current
channel. The window picture displays the
channel selected from the menu.
Move
To cancel the favorite channel menu before
selecting a channel, move the joystick up or down
to select EXIT at the bottom of the menu and press
.
FAVORITES
12 CNN
36 ESPN
50
60
70
80
90
120 MTV
EXIT
2 Move the joystick up or down to select the
channel that you wish to view from the menu.
Select
Exit
MENU
For detailed information on using the remote
control to modify menu settings, refer to “Learning
Menu Selection” on page 35.
To select the SET UP
Display
, Highlight
menu:
, Select
MENU
The picture of the selected channel will be
displayed in the window picture.
PARENTAL CONTROL
— Blocks programs unsuitable for children
FAVORITES
12 CNN
36 ESPN
50
60
70
80
90
120 MTV
EXIT
Allows you to block TV programs that you feel are
unsuitable for your children.
(see “Using the PARENTAL CONTROL Feature”
on page 47 for details)
44
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
masterpage:Right
CAPTION VISION
SELECT OUT
— Television closed caption display
— Output signal selection from SELECT
OUT
Some programs are
SET UP
PARENTAL CONTROL
CAPTION VISION
CC1
broadcast with Caption
SELECT OUT:MONITOR CC2
LANGUAGE: ENGLISH CC3
Vision.
VIDEO LABEL
CC4
DIRECT PLAY
TEXT1
To display Caption Vision,
TEXT2
FREEZE MODE:NORMAL
DTV INPUT:
Y PBTEXT3
PR
select [CC] 1, [CC] 2, [CC]
TEXT4
3, [CC] 4, TEXT1,
Move
Select
Exit
TEXT2, TEXT3 or TEXT4 from the menu. Then
press the [CC] button until Caption Vision is
displayed.
You can select the desired
output signal from the
SELECT OUT jacks at the
rear of the projection TV.
If you select TV OUT, the following pop-up menu
appears.
SET UP
PARENTAL CONTROL
CAPTION VISION
CC1
SELECT OUT:
MONITOR
LANGUAGE: ENGLISH
VIDEO1
VIDEO LABEL
VIDEO2
DIRECT PLAY
VIDEO3
FREEZE MODE:NORNAL
VIDEO4
DTV INPUT:
R.G.B
TV OUT
MENU
Move
Select
Exit
MENU
[CC] 1, [CC] 2, [CC] 3 or [CC] 4 displays a printed
version of the dialogue or sound effects of a
program. (The mode should be set to [CC] 1 for
most programs.) TEXT1, TEXT2, TEXT3 or
TEXT4 displays network/station information
presented using either half or the whole screen.
MONITOR:
Select to edit tapes while monitoring. SELECT
OUT outputs the picture displayed on the screen.
Note:
• Poor reception of TV programs can cause errors in
Caption Vision and XDS.
Captions may appear with a white box or other
errors instead of the intended text.
VIDEO1–VIDEO4:
Select to edit tapes while viewing an input image
different from that being recorded. SELECT OUT
outputs the signal input to the projection TV
regardless of the displayed picture on the screen.
TV OUT:
Select if you connect an AV receiver to VIDEO 1
IN. SELECT OUT outputs the signal that the TV is
tuned to, regardless of the displayed picture. (see
“Connecting an AV Receiver” on page 20 for
connection)
SET UP
PARENTAL CONTROL
CAPTION VISION:
CC1
SELECT OUT:
MONITOR
LANGUAGE:
VIDEO1
VIDEO LABEL
VIDEO2
DIRECT PLAY
VIDEO3
FREEZE MODE:
VIDEO4
DTV INPUT:
R.G.B
TV OUT
DTV
ASPECT:
4:3
Set up
using
YES
only VIDEO1 input?
NO
Move
Select
Exit MENU
Select NO if you have connected multiple
components to your projection TV. You can select
an input (VIDEO1 – VIDEO4) with the TV/
VIDEO button.
Adjusting Your SET UP (menus)
Note:
• SELECT OUT setting is not available for the
inputs from VIDEO 5 (DTV) IN.
Select YES only if you
have connected an AV
receiver, with no other
equipment, to your
projection TV. You can
always select the signal
from the receiver by
pressing TV/VIDEO once.
Note:
• The SELECT OUT signal is only available when
the projection TV is on.
LANGUAGE
— User’s preferred language
Select from available languages (ENGLISH or
ESPAÑOL) to display all menus in your language
of choice.
45
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
masterpage:Left
VIDEO LABEL
DIRECT PLAY
— Easy recognition of connected
equipment (e.g. SAT, VHS, etc.)
— Easy operation of a connected VCR
This feature allows you to
label each input mode so
that you can easily identify
the connected equipment
(e.g. you can label VIDEO
1 IN as VHS).
VIDEO LABEL
VIDEO1:
VIDEO2:
VIDEO3:
VIDEO4:
VIDEO5:
VIDEO1
VIDEO2
VIDEO3
VIDEO4
VIDEO5
Select
Exit
MENU
1 Move the joystick up or down to select the input
mode you want to label and press .
VIDEO LABEL
Move
— Freeze picture mode
This feature allows you to
DIRECT PLAY
VIDEO1:
OFF
switch the input mode from
VIDEO2:
OFF
VIDEO3:
OFF
the TV to a Sony VCR
VIDEO4:
OFF
(MDP or DVD) and start
playing by only pressing
the N (playback) button
Move
Select
Exit
on the remote control. You have to set the AV 1/2/
3/DVD/MDP switch on the remote control (e.g.,
you connect your VCR to the VIDEO 3 IN jacks
and set the AV 1/2/3/DVD/MDP switch to VTR 3).
With the DIRECT PLAY window open:
1
2
3
DVD/MDP
MENU
Move
With the VIDEO LABEL window open:
VIDEO1:
VIDEO2:
VIDEO3:
VIDEO4:
VIDEO5:
FREEZE MODE
VIDEO1
VHS
8mm
BETA
LD
SAT
DVD
AV RECEIVER
SKIP
Select
Exit MENU
2 Move the joystick up or down to select the label
and press .
VIDEO LABEL Options:
VIDEO 1: VIDEO 1, VHS, 8mm, BETA, LD,
SAT, DVD, AV RECEIVER, SKIP
VIDEO 2–4: VIDEO 2–4, VHS, 8mm, BETA,
LD, SAT, DVD, SKIP
VIDEO 5: VIDEO 5, DTV, DVD, SKIP
If you select SKIP, your projection TV will skip this
connection when you scan through video sources
using the TV/VIDEO button.
1 Move the joystick up or down to select the input
to which your video equipment is connected,
and press .
DIRECT PLAY
VIDEO1:
VIDEO2:
VIDEO3:
VIDEO4:
1
2
Move
3
OFF
AV1
AV2
AV3
DVD/MDP
Useful when you need to copy down information
that appears on the TV’s screen.
Note:
• The FREEZE MODE feature is not available for
the inputs from VIDEO 5 (DTV) IN jacks.
NORMAL:
Select to freeze the whole picture on the screen by
pressing FREEZE.
R e c ip e
flour - - - - 2
s u g a r - - - 1/2
s a l t - - - - - 1/2
butter - - - 1
The current picture freezes.
DVD/MDP
Select
Exit
MENU
2 Move the joystick up or down to select the
position of the AV 1/2/3/DVD/MDP switch, and
press .
TWIN:
Select to freeze the desired scene and display it on
the left of the screen while viewing the normal
picture of the current channel on the right by
pressing FREEZE.
Note:
• DIRECT PLAY setting is not available for the
inputs from VIDEO 5 (DTV) IN.
46
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
This mode is not available for PIP, P&P or CH
INDEX screens.
Frozen
picture
6
R e c ip e
flour - - - - 2
s u g a r - - - 1/2
s a l t - - - - - 1/2
butter - - - 1
Normal
motion
picture
Press FREEZE again or press (OFF) to display
the normal picture.
–– Input signal selection from the DTV
receiver
Select Y PB PR when you connect a DTV
receiver to the Y/PB/PR jacks of VIDEO 5 (DTV)
IN.
Select R.G.B when you connect a DTV receiver to
the G/B/R/HD/VD jacks of VIDEO 5 (DTV) IN
on the rear of the projection TV.
Using the PARENTAL
CONTROL Feature
The TV programs and movies shown on TV are
given a rating signal based on the following rating
systems: Television Parental Guidelines to rate
television programs (TV ratings), and Motion
Picture Association of America (MPAA)
Guidelines to rate movies including those shown
on TV (movie ratings)
Note:
• The PARENTAL CONTROL feature is not
available for the inputs from VIDEO 5 (DTV) IN.
Activating the PARENTAL
CONTROL feature
First, set a password, then select your desired
rating from Sony’s predetermined ratings.
2 Enter a four digit password* using the 0–9
buttons.
SET UP
PARENTAL CONTROL
CAPTION VISION:
CONFIRM
PASSWORD
SELECT OUT:
_ ___
LANGUAGE:ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE:NORMAL
DTV INPUT:
Y PB PR
Confirm password
Move
Exit
MENU
* Do not enter “4357” corresponding to “HELP”
on a phone number pad. (see page 52)
3 To confirm the password, re-enter the same
Adjusting Your SET UP (menus)
DTV INPUT
masterpage:Right
password with the 0–9 buttons.
Your password is stored and the PARENTAL
CONTROL menu automatically appears.
If you want to change the password, see page
51.
PARENTAL CONTROL
PARENTAL LOCK: OFF
RATING:
CHILD
CHANGE PASSWORD
1 Select PARENTAL CONTROL from the SET
UP menu. (see page 44)
Move
SET UP
PARENTAL CONTROL
SET NEW
CAPTION VISION:
PASSWORD
SELECT OUT:
_ ___
LANGUAGE:ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE:NORMAL
DTV INPUT:
Y
PB PR
R.G.B
Use [0-9] to enter
password
DTV ASPECT:
4:3
Move
Exit MENU
Select
Exit
MENU
4 Make sure that PARENTAL LOCK is
highlighted, and press
.
PARENTAL CONTROL
PARENTAL LOCK: ON
OFF
RATING:
CHILD
CHANGE PASSWORD
Move
Select
Exit
MENU
(continued)
47
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
5 Move the joystick up or down to select ON,
and press
.
masterpage:Left
To deactivate the PARENTAL
CONTROL feature
If you set PARENTAL LOCK in the PARENTAL
CONTROL menu to OFF, the PARENTAL
CONTROL feature will be canceled and you can
view all TV programs and movies shown on TV.
PARENTAL CONTROL
PARENTAL LOCK: ON
RATING:
CHILD
CHANGE PASSWORD
1 Select PARENTAL CONTROL from the SET
Move
Select
Exit
MENU
6 Move the joystick up or down to select
RATING, and press
.
PARENTAL CONTROL
PARENTAL LOCK: ON
CHILD
RATING:
YOUTH
CHANGE PASSWORD
YOUNG ADULT
CUSTOM
Exit
7 Move the joystick up or down to select a
desired rating (CHILD, YOUTH and YOUNG
ADULT), and press .
If you want to select the ratings from
“CUSTOM,” go to step 4 of “Selecting a
Custom Rating” on page 49.
8 Press MENU to exit the menu.
.
PARENTAL CONTROL
PARENTAL LOCK: ON
OFF
RATING:
CHILD
CHANGE PASSWORD
Move
Select
Exit
MENU
4 Move the joystick up or down to select OFF,
SET UP
PARENTAL CONTROL
CAPTION VISION:
PASSWORD
SELECT OUT: _ _ _ _
LANGUAGE:ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE:NORMAL
DTV INPUT:
Y PB PR
Use [0-9] to enter
password
Move
Exit MENU
and press
The PARENTAL CONTROL menu appears.
PARENTAL CONTROL
PARENTAL LOCK: ON
RATING:
CHILD
CHANGE PASSWORD
Move
Select
Exit
.
PARENTAL CONTROL
PARENTAL LOCK: OFF
RATING:
CHILD
CHANGE PASSWORD
2 Enter your four digit password using the 0–9
MENU
PARENTAL LOCK, and press
UP menu. (see page 44)
buttons.
Age up to 6
Move
Select
3 Move the joystick up or down to select
Move
Select
Exit
MENU
5 Press MENU to exit the menu.
To unlock the PARENTAL CONTROL
feature temporarily
MENU
When you select a PARENTAL CONTROL
program, no sound or picture except for a channel
number will appear. The
indicator is displayed.
To view the program, follow the steps below.
1 Press ENTER to display the “Password”
screen.
2 Enter your password using the 0–9 buttons.
PARENTAL CONTROL will be canceled
(PARENTAL LOCK set to OFF) until you turn
your projection TV off.
48
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
Selecting a Custom Rating
If you want to select the ratings to be blocked from
CUSTOM once you have activated the
PARENTAL CONTROL feature (see page 47),
follow the procedure below.
For a detailed description of each rating, see pages 52
and 53.
masterpage:Right
3 Move the joystick up or down to select
RATING, and press
7 Move the joystick up or down to select
, and
press .
The
indicator automatically appears beside
the selected rating and all “higher” ratings,
indicating that the programs that match the
ratings will be blocked.
.
PARENTAL CONTROL
PARENTAL LOCK: ON
CHILD
RATING:
YOUTH
CHANGE PASSWORD
YOUNG ADULT
CUSTOM
Age up to 6
Move
Select
Exit
TV RATING
MENU
TV–Y _
TV–Y7 _
TV–G _
TV–PG –
TV–14 –
TV–MA–
1 Select PARENTAL CONTROL from the SET
UP menu. (see page 44)
2 Enter your four digit password using the 0–9
buttons.
The PARENTAL CONTROL menu appears.
PARENTAL CONTROL
PARENTAL LOCK: ON
RATING:
CHILD
CHANGE PASSWORD
CUSTOM, and press
.
Select category
Move
Select
First, select a TV rating.
Select
Exit
RATING, and press
MENU
Some ratings have additional content ratings
called “extenders.” The extenders are defined
as follows: D (sexually suggestive Dialog), FV
(Fantasy Violence), L (coarse Language), S
(Sexual situations) and V (Violence). By
setting the extenders, you can define additional
viewing limits. For more details of extenders,
see page 53.
.
TV RATING
TV–Y _
TV–Y7 _
TV–G _
TV–PG _
TV–14 _
TV–MA _
:FV _
:D _ L _ S _ V _
:D _ L _ S _ V _
:
L_S_V_
Select rating
Move
Select
Exit
MENU
6 Move the joystick up or down to select the TV
MENU
Exit
5 Move the joystick up or down to select TV
rating to be blocked, and press
Move
:D – L – S – V –
:D – L – S – V –
:
L–S–V
Adjusting Your SET UP (menus)
SET UP
PARENTAL CONTROL
CAPTION VISION:
PASSWORD
SELECT OUT: _ _ _ _
LANGUAGE:ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE:NORMAL
DTV INPUT:
Y PB PR
Use [0-9] to enter
password
Move
Exit MENU
4 Move the joystick up or down to select
:FV _
.
All of the extenders included in the selected
ratings will be blocked. If you wish to allow
any of them to be viewed, go to step 8.
(continued)
TV RATING
TV–Y
TV–Y7
TV–G
TV–PG
TV–14
TV–MA
_
_
_
_
_
:FV _
:D _ L _ S _ V _
:D _ L _ S _ V _
:
L_S_V_
Allow rating
Move
Select
Exit
MENU
49
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
8 Move the joystick left or right to select the
extender to be viewed, and press
.
TV RATING
TV–Y _
TV–Y7 _
TV–G _
TV–PG –
TV–14 –
TV–MA–
:FV _
:D – L – S – V –
:D – L – S – V –
:
L–S–V
Block content
Move
Select
Exit
masterpage:Left
10 Repeat steps 8 and 9 for other extenders.
13 Move the joystick up or down to select the
All programs that match the ratings you select
and higher, except for the extenders that were
canceled, will be blocked.
movie rating to be blocked, and press
MOVIE RATING
–
G
–
PG
PG–13 –
–
R
NC–17 –
–
X
11 After setting of the TV rating is complete,
move the joystick up or down to select
and press .
,
Block rating
Move
Select
MENU
CUSTOM RATING
9 Move the joystick up or down to select
“–,” and press
TV RATING
MOVIE RATING
UNRATED: VIEW ALL
“–” appears beside the selected extender,
indicating that the programs that match the
extender can be viewed.
If you select ,
is displayed to show that
the programs that match the extender will be
blocked again.
TV RATING
TV–Y _
TV–Y7 _
TV–G _
TV–PG –
TV–14 –
TV–MA–
:FV _
:D – L – S – V _
:D – L – S – V –
:
L–S–V
Select category
Move
Select
press
Select category
Move
Select
Exit
MENU
Second, select a movie rating.
12 Move the joystick up or down to select MOVIE
RATING, and press
MENU
, and
.
The
indicator automatically appears beside
the selected rating and all “higher” ratings,
indicating that the programs that match the
ratings will be blocked.
.
MOVIE RATING
–
G
–
PG
PG–13 –
–
R
NC–17 –
–
X
MOVIE RATING
–
G
–
PG
PG–13 –
–
R
NC–17 –
–
X
Select rating
Move
Select
Exit
Exit
14 Move the joystick up or down to select
.
.
Select rating
Move
Select
Exit
Exit
MENU
MENU
MENU
15 Press MENU to exit the menu.
50
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
To block TV programs and/or
movies for which a rating signal is
not given (NR and N/A)
For a description of the NR and N/A ratings, see page
53.
1 Perform steps 1–4 of “Selecting a Custom
Rating” on page 49.
2 Move the joystick up or down to select
UNRATED, and press
.
Select ...
No program
(to view any unrated
TV program and
movie)
VIEW ALL
Unrated TV programs
TV
Unrated movies
MOVIE
Unrated TV programs
and movies
BOTH
4 Press MENU to exit the menu.
CUSTOM RATING
Exit
Changing the Password
1 Select PARENTAL CONTROL from the SET
UP menu. (see page 44)
SET UP
PARENTAL CONTROL
CAPTION VISION:
PASSWORD
SELECT OUT: _ _ _ _
LANGUAGE:ENGLISH
VIDEO LABEL
DIRECT PLAY
FREEZE MODE:NORMAL
DTV INPUT:
Y PB PR
Use [0-9] to enter
password
Move
Exit MENU
2 Enter your four digit password using the 0–9
Adjusting Your SET UP (menus)
TV RATING
MOVIE RATING
UNRATED: VIEW ALL
TV
MOVIE
BOTH
No block
Move
Select
To block ...
masterpage:Right
buttons.
The PARENTAL CONTROL menu appears.
PARENTAL CONTROL
PARENTAL LOCK: ON
RATING:
CHILD
CHANGE PASSWORD
MENU
3 Move the joystick up or down to select the type
of programs to be blocked, and press
.
Move
Select
Exit
MENU
CUSTOM RATING
TV RATING
MOVIE RATING
UNRATED: BOTH
Block all unrated
programming
Move
Select
Exit
3 Move the joystick up or down to select
CHANGE PASSWORD, and press
MENU
.
PARENTAL CONTROL
PARENTAL LOCK: ON
CHILD
RATING:
CHANGE PASSWORD
NEW
____
Use [0-9] to enter
new four digit
password
Move
Exit
MENU
(continued)
51
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
4 Enter a new four digit password using the 0–9
buttons.
PARENTAL CONTROL
PARENTAL LOCK: ON
CHILD
RATING:
CHANGE PASSWORD
COMFIRM
____
Confirm password
Move
Exit
MENU
5 Enter the password set in step 4 again to
confirm.
If you entered it incorrectly, “Password
incorrect” appears.
Re-enter the correct password.
6 Press MENU to exit the menu.
If you have forgotten your
password
In step 1 of “Changing the Password,” enter the
master password “4357” (corresponding to
“HELP” on a phone number pad). You can then
store a new password.
Notes:
• If you entered “4357” as your password the first
time, you cannot store a new password. (see step 2
of “Activating the PARENTAL CONTROL feature”
on page 47)
• When you select a PARENTAL CONTROL
program and the
indicator is displayed on the
screen, you cannot view that program even if you
enter “4357.” (see “To unlock the PARENTAL
CONTROL feature temporarily” on page 48)
masterpage:Left
What the Ratings
Mean
Sony’s predetermined ratings
These are original ratings that Sony predetermined
according to the viewer’s age. Each rating allows
you to view the certain programs, as follows.
See the center column to page 53 for a description of
TV and movie ratings.
CHILD:
Suitable for children under the age of 6.
Viewable movie ratings: G, NR, and N/A
Viewable TV ratings: TV-Y, TV-G, and TV-NR
YOUTH:
Suitable for children aged 7 and older.
Viewable movie ratings: G, PG, NR, and N/A
Viewable UTV ratings: TV-Y, TV-Y7, TV-G, TVPG, and TV-NR
YOUNG ADULT:
Suitable for children aged 14 and older.
Viewable movie ratings: G, PG, PG-13, NR, and
N/A
Viewable TV ratings: TV-Y, TV-Y7, TV-G, TVPG, TV-14, and TV-NR
Movie ratings
Movie ratings are for movies (including those
shown on TV) rated according to the Motion
Picture Association of America (MPAA)
Guidelines.
G (General Audiences—All Ages
Admitted):
In G-rated films no strong words are used, the
violence is at a minimum, nudity and sex scenes
are not present, nor is there any drug use.
PG (Parental Guidance Suggested. Some
Material May Not Be Suitable For
Children):
This is a film which may need to be monitored first
by parents.
PG-13 (Parents Strongly Cautioned. Some
Material May Be Inappropriate For Children
Under 13):
Parents are alerted to be very careful about the
attendance of their under-teenage children when
viewing.
R (Restricted, Under 17 Require
Accompanying Parent Or Adult Guardian):
This film includes hard language, tough violence,
nudity, drug abuse or other elements of concern.
NC-17 or X (No One 17 Or Under
Admitted.):
This is a film that most parents would consider not
suitable for children aged 17 and under. There may
be violence, sex, aberrational behavior, drug abuse
or other elements of concern.
52
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\09CTV.fm
NR (Not Rated):
This is a film that a producer has not rated,
intending to have his film widely released.
N/A (Not Applicable):
This is a film that a producer considers outside the
scope of the MPAA ratings.
Note:
• NR and N/A ratings are shown together as
UNRATED in the menu.
TV-Y (All Children):
This program is designed for young children aged
2–6 and is appropriate for all children.
TV-Y7 (Directed to Older Children):
This program is designed for children aged 7 and
above. Themes and elements in this program may
include mild fantasy violence or slapstick
violence, or may frighten children under the age of
7.
TV-G (General Audience):
Most parents would find this program suitable for
all ages. It contains little or no violence, no strong
language and little or no sexual dialog or
situations.
TV-PG (Parental Guidance Suggested):
This program contains some material that parents
may find unsuitable for younger children.
TV-14 (Parents Strongly Cautioned):
This program contains some material that many
parents would find unsuitable for children under
the age of 14.
V (Violence):
Programs containing violence
There may be some profanity, violence or brief
nudity in these programs.
TV-MA (Mature Audience Only):
This program is specifically designed to be viewed
by adults and therefore may be unsuitable for
children under the age of 17.
TV-NR (Not Rated/Unrated):
This is a program broadcast without any rating,
such as news, news flashes or sports.
Adjusting Your SET UP (menus)
TV ratings
TV ratings are for TV programs rated according to
the Television Parental Guidelines.
masterpage:Right
Note:
• The TV-NR rating is shown as UNRATED in the
menu.
About the extenders of TV ratings
TV-Y7, TV-PG, TV-14 and TV-MA ratings have
additional content ratings called “extenders” to
define additional viewing limits. The extenders are
defined as follows:
D (sexually suggestive Dialog):
Programs containing suggestive dialog, or sexual
innuendo
FV (Fantasy Violence):
Programs containing cartoon violence occurring in
TV-Y7 programs only
L (coarse Language):
Programs containing coarse language
S (Sexual situations):
Programs containing sexual content
53
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\10OVE.fm
Additional Operations
masterpage:First-Left
If the remote control doesn’t work
• See the tips on page 56.
VCR manufacturer code numbers
Operating Video
Equipment
Setting the Manufacturer’s
Code
You can use the supplied remote control to operate
Sony or non-Sony video equipment that has an
infrared sensor.
1 Set the AV1/2/3/DVD/MDP switch to the input
through which you would like to access your
video equipment.
The following Sony equipment is preset to
each input as shown below:
AV1 (303)
Beta, ED Beta VCRs
AV2 (302)
8 mm VCR
AV3 (301)
VHS VCR
DVD/MDP (751) DVD Player
2 Press CODE SET, DVD/VCR (FUNCTION),
and the 0-9 buttons to enter the manufacturer’s
code number (see the following chart), then
press ENTER.
For example, to operate a Sony 8mm VCR:
CODE SET
FUNCTION
DVD/VCR
ENTER
3
0
2
Manufacturer
Code
Sony
Aiwa
Admiral (M. Ward)
Audio Dynamic
Bell & Howell (M. Ward)
Broksonic
Canon
Citizen
Craig
Criterion
Curtis Mathis
Daewoo
DBX
Dimensia
Emerson
Fisher
Funai
General Electric
Go Video
Goldstar
Hitachi
Instant Replay
JC Penney
301, 302, 303
338
327
314, 337
330, 343
319, 317
309, 308
332
315, 302, 332
315
304, 338, 309
341, 312, 309
314, 336, 337
304
319, 320, 316, 317, 318, 341
330, 334, 335, 333
338
329, 304, 309
340, 339, 322
332
306, 304, 305, 338
309, 308
309, 305, 304, 330, 314, 336,
337
314, 336, 337
314, 336, 332, 337
332, 305, 333, 334, 330, 335,
338
308, 309, 310
314, 336, 337
332
309, 335
305, 304
JVC
Kenwood
LXI (Sears)
Magnavox
Marantz
Marta
Memorex
Minolta
Mitsubishi/MGA
Multitech
NEC
Olympic
Optimus
Panasonic
Pentax
Philco
Philips
Pioneer
Quasar
RCA/PROSCAN
Realistic
Sansui
Singer
Samsung
Sanyo
Scott
Sharp
Shintom
Signature 2000 (M. Ward)
Sylvania
Symphonic
SV2000
Tashiro
Tatung
Teac
Technics
Teknica
Toshiba
Wards
XR-1000
Yamaha
Zenith
323, 324, 325, 326
325, 338, 321
314, 336, 337
309, 308
327
308, 309, 306, 307
305, 304
308, 309
308, 309, 310
308
308, 309, 306
304, 305, 308, 309, 311, 329,
312, 313, 310
309, 330, 328, 335, 324, 338
314
315
322, 313, 321
330, 335
312, 313, 321, 335, 323, 324,
325, 326
327, 328
315
338, 327
308, 309, 338, 310
338
338
332
314, 336, 337
314, 336, 338, 337
309, 308
342, 338
312, 311
327, 328, 335, 331, 332
315
330, 314, 336, 337
331
54
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\10OVE.fm
MDP manufacturer code numbers
Manufacturer
Code
Sony
Panasonic
Pioneer
701
704
702
DVD Player manufacturer code
numbers
Manufacturer
Code
Sony
Panasonic
Pioneer
RCA
Toshiba
751
753
752
755
754
• In some rare cases, you may not be able to operate
your non-Sony video equipment with the supplied
remote control. In this case, please use the
equipment’s own remote control.
• When you remove the batteries, the code number
may revert to the factory setting.
Operating video equipment
1 Set the AV1/2/3/DVD/MDP switch to the input
through which you would like to access your
video equipment.
Operating a VCR using the remote
control
Operating a DVD Player using the
remote control
To turn On/Off
To turn On/Off
To select a channel
To change channels
To record
To play
To stop
To fast forward
To rewind the tape
To pause
To search the picture
forward or backward
To change input mode
Press DVD/VCR (POWER).
[Green Button]
Press the 0 – 9 buttons.
Press CH +/–.
Press
(REC) while pressing
(lower).
Press N.
Press x.
Press M.
Press m.
Press X. Press again to resume
normal playback.
Press M or m during playback.
Release to resume normal
playback.
Press TV/VCR.
Operating an MDP using the
remote control
To turn On/Off
To play
To stop
To pause
To search the picture
forward or backward
To search a chapter
forward or backward
To play
To stop
To pause
To step through
different tracks of an
audio disc
To step through
different chapters of a
video disc
To display the Title
menu
To display the DVD
menu
To select tracks
directly
To display the menu
(Set up)
Press DVD/VCR (POWER).
[Green Button]
Press N.
Press x.
Press X. Press again to resume
normal playback.
Press M to step forward or m
to step backward.
Press CH+ to step forward or CH–
to step backward.
Press TITLE.
Press DVD MENU.
Additional Operations
Tips z
masterpage:Right
Press 0-9 buttons.
Press MENU.
Press DVD/VCR (POWER).
[Green Button]
Press N.
Press x.
Press X. Press again to resume
normal playback.
Press M or m during playback.
Release to resume normal
playback.
Press CH +/–.
2 Press DVD/VCR (FUNCTION).
3 Use the VCR/DVD/MDP operation buttons
indicated in the following tables.
55
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\10OVE.fm
Operating a Cable Box
or Satellite Receiver
(SAT)
Setting the Manufacturer’s
Code
You can program the supplied remote control to
operate a cable box or satellite receiver.
Press CODE SET, SAT/CABLE (FUNCTION),
and the 0-9 buttons to enter the manufacturer’s
code number (see the following chart), then press
ENTER.
For example, to operate a Sony satellite receiver:
CODE SET
FUNCTION
SAT/CABLE
ENTER
8
0
1
masterpage:Left
Manufacturer code numbers (cable
box)
Manufacturer
Code
Gemini
Hamlin/Regal
Jerrold/G. I.
233
222, 223, 224, 225, 226
201, 202, 203, 204, 205, 222,
206, 207, 208, 218
230, 231, 232
234
227, 228, 229
219, 220, 221
236, 237, 238, 239, 240, 241
214, 215
235
209, 210, 211
216, 217
212, 213
Macom
Magnavox
Oak
Panasonic
Philips
Pioneer
Samsung
Scientific Atlanta
Tocom
Zenith
Manufacturer code numbers
(Satellite receiver)
Manufacturer
Code number
Sony
801 (preset code for remote
control)
802
802
General Electric
RCA/PROSCAN
receiver.
If the remote control doesn’t work
• Try repeating the set up procedures using the
other codes listed for your equipment.
To operate the projection TV
Press TV (FUNCTION). Then use the projection
TV control buttons to control the projection TV.
Tips z
• If more than one code number is listed, try entering
them one by one until you come to the correct code
for your equipment.
• If you enter a new code number, the code number
you previously entered at that setting is erased.
• In some rare cases, you may not be able to operate
your equipment with the supplied remote control. In
this case, use the equipment’s own remote control
unit.
• Whenever you remove the batteries — to replace
them, for example — if too much time is taken, the
code numbers may revert to the factory setting and
must be reset.
Operating a cable box or
satellite receiver
1 Press SAT/CABLE (POWER) [Green Button]
to turn on/off the cable box or satellite receiver.
2 Press SAT/CABLE (FUNCTION).
3 For other operations, refer to the operating
56
instructions that come with the equipment.
Blue-labeled buttons such as the GUIDE
button can be used only with a satellite
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\11TRB.fm
Additional Information
Troubleshooting
If, after reading the following
instructions, you have additional
questions related to the use of your Sony
projection TV, please call one of the
following numbers (English only).
Customers in the continental United States
contact the Sony Customer Information
Service Center at:
1-800-222-SONY (7669)
Customers in Canada contact the Sony
Customer Relations Center at:
(416) 499-SONY (7669)
b The projection TV is equipped with a selfdiagnosis function. If there is a problem with your
projection TV, the TIMER/STAND BY indicator
on the front panel will flash repeatedly. Counting
the number of flashes helps you inform qualified
Sony personnel of the projection TV’s condition.
1 Count how many times the TIMER/STAND BY
indicator flashes in total. It flashes twice at 3
seconds’ intervals. If, for example, the indicator
flashes twice, stops flashing for 3 seconds, and
flashes twice again, that counts as twice.
2 Press POWER on the projection TV to turn it
off, then inform qualified Sony personnel or the
above Direct Response Center of the number of
flashes.
No picture (screen not lit), no sound
b Make sure the power cord is plugged in.
b Operate with the buttons on both the projection TV
and the remote control.
b Check to see if the TV/VIDEO setting is correct:
when watching TV, set to TV, and when watching
video tapes, set to VIDEO 1, 2, 3, 4 or 5.
b Try another channel. It could be station trouble.
b Perform AUTO SET UP again using the SET UP
button to return to the factory preset condition. (see
“To perform AUTO SET UP again” on page 25)
b The PARENTAL CONTROL feature is activated.
(see “Using the PARENTAL CONTROL Feature”
on page 47)
Remote control does not operate
b Batteries could be weak. Replace the batteries.
b Press TV (FUNCTION) when operating your
projection TV.
Dark, poor or no picture (screen lit),
good sound
b Adjust PICTURE in the VIDEO menu. (see
“PICTURE” on page 36)
b Adjust BRIGHTNESS in the VIDEO menu. (see
“BRIGHTNESS” on page 36)
b Check antenna/cable connections.
b Perform AUTO SET UP again using the SET UP
button to return to the factory preset condition. (see
“To perform AUTO SET UP again” on page 25)
b Adjust the convergence again using the FLASH
FOCUS button. (see “Adjusting the Convergence
Automatically (FLASH FOCUS)” on page 25)
Good picture, no sound
b Press MUTING so that “MUTING” disappears
from the screen. (see “MUTING” on page 26)
Additional Information
The picture turns off and the TIMER/
STAND BY indicator on the front panel
flashes (self-diagnosis function)
masterpage:First-Right
b Check the MTS setting in the AUDIO menu. (see
“MTS” on page 37)
b Make sure SPEAKER is set to ALL ON or L/R
OFF in the AUDIO menu. (see “SPEAKER” on
page 38)
b Perform AUTO SET UP again using the SET UP
button to return to the factory preset condition. (see
“To perform AUTO SET UP again” on page 25)
(continued)
b Make sure the projection TV’s power cord is
connected securely to the wall outlet.
TIMER /
STAND BY
flashing
b Locate the projection TV at least 3-4 feet away
from fluorescent lights.
b Check the polarity of the batteries.
57
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\11TRB.fm
Cannot receive digital channels (when a
DTV receiver is connected)
masterpage:Left
Only snow and noise appear on the
screen
Cannot operate the menu
b Check the DTV INPUT setting in the SET UP
menu. (see “DTV INPUT” on page 47)
b Check the CABLE setting in the CHANNEL SET
UP menu. (see “CABLE” on page 42)
b Check the connections between the DTV receiver
and the projection TV. (see pages 12 and 13)
b Check the antenna/cable connections.
b Check your local listings to find out if you can
receive digital broadcasts in your area.
Cannot receive upper channels (UHF)
when using an antenna
b Make sure CABLE is OFF in the CHANNEL SET
UP menu. (see “CABLE” on page 42)
b Use AUTO PROGRAM to add receivable channels
that are not presently in the TV’s memory. (see
“AUTO PROGRAM” on page 42)
No color
b Adjust the COLOR in the VIDEO menu. (see
“COLOR” on page 36)
b Black and white programs cannot be seen in color.
b Perform AUTO SET UP again using the SET UP
button to return to the factory preset condition. (see
“To perform AUTO SET UP again” on page 25)
b Make sure the channel is broadcasting programs.
b Press ANT to change the input mode. (see “ANT”
on page 26)
b If the item you want to choose appears in gray, you
cannot select it.
b Press the projection TV’s power button off and on
again.
Cannot receive any channels when
using cable TV
b Check the connection with a cable box again. (see
pages 9 and 11)
Dotted lines or stripes
b Make sure CABLE is ON in the CHANNEL SET
UP menu. (see “CABLE” on page 42)
b Adjust the antenna.
b Keep the projection TV away from noise sources
such as cars, neon signs or hair-dryers.
TV is fixed to one channel
b Use AUTO PROGRAM to add receivable channels
that are not presently in TV’s memory. (see “AUTO
PROGRAM” on page 42)
b Try turning CHANNEL FIX off. (see “CHANNEL
FIX” on page 42)
Double images or ghosts
b Use a highly directional outdoor antenna or a cable
(when the problem is caused by reflections from
nearby mountains or tall buildings).
b Use AUTO PROGRAM to add receivable channels
that are not presently in the TV’s memory. (see
“AUTO PROGRAM” on page 42)
Cannot gain enough volume when using
a cable box
b Increase the volume at the cable box. Then press
TV (FUNCTION) and adjust the projection TV’s
volume.
CHANNEL INDEX does not display all
available channels
b Make sure CABLE is ON in the CHANNEL SET
UP menu. (see “CABLE” on page 42)
b Use AUTO PROGRAM to add receivable channels
that are not presently in the TV’s memory. (see
“AUTO PROGRAM” on page 42)
58
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\11TRB.fm
masterpage:Right
FAVORITE CHANNEL does not display
your choices
b Verify that FAVORITE CHANNEL is set to
MANUAL in the CHANNEL SET UP menu. (see
“Setting FAVORITE CHANNEL manually” on
page 43)
Some video sources do not appear when
you press TV/VIDEO
b Ensure that VIDEO LABEL is not set to SKIP. (see
“VIDEO LABEL” on page 46)
Recording through SELECT OUT does
not function properly when recording in
PIP or P&P mode
Additional Information
b SELECT OUT will not record both images in PIP
or P&P. Only the main picture will be recorded.
b If you are recording the main picture and you
switch to the sound of the sub picture using the
AUDIO button, the main picture will be recorded
with sound from the other program.
Cannot play shooting games
b Some shooting games which involve pointing a
light beam at the TV screen with an electronic gun
or rifle cannot be used with this projection TV. For
details, see the instruction manual supplied with the
video game software.
59
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\11TRB.fm
Specifications
Projection system
3 picture tubes, 3 lenses, horizontal in-line system
Picture tube
7-inch high-brightness monochrome tubes (6.3 raster size),
with optical coupling and liquid cooling system
Projection lenses
High performance, large diameter hybrid lens F1.1
Television system
American TV standard
Channel coverage
VHF: 2–13/UHF: 14 –69/CATV: 1 – 125
Antenna
75 ohm external terminal for VHF/UHF
Screen size (measured diagonally)
57 inches (KP-57XBR10W)
65 inches (KP-65XBR10W)
Inputs/outputs
VIDEO 1/3 IN
VIDEO 2 INPUT
S VIDEO IN (4-pin mini DIN):
Y: 1 Vp-p, 75-ohms unbalanced, sync negative
C: 0.286 Vp-p (Burst signal), 75 ohms
VIDEO (phono jack): 1 Vp-p, 75-ohms unbalanced, sync
negative
AUDIO (phono jacks): 500 mVrms (100% modulation),
Impedance: 47 kilohms
VIDEO 4 IN
S VIDEO IN (4-pin mini DIN):
Y: 1 Vp-p, 75-ohms unbalanced, sync negative
C: 0.286 Vp-p (Burst signal), 75 ohms
VIDEO (phono jack): 1 Vp-p, 75-ohms unbalanced, sync
negative
AUDIO (phono jacks): 500 mVrms (100% modulation),
Impedance: 47 kilohms
Y: 1 Vp-p, 75 ohms, sync negative
PB: 0.7 Vp-p, 75 ohms
PR: 0.7 Vp-p, 75 ohms
masterpage:Left
VIDEO 5 (DTV) IN
Maximum scanning rate: 1080i
Y: 1 Vp-p, 75 ohms, negative or tri-level sync
PB: 0.7 Vp-p, 75 ohms
PR: 0.7 Vp-p, 75 ohms
or
G: 0.7 Vp-p
B: 0.7 Vp-p
R: 0.7 Vp-p
HD: 0.5–5 Vp-p, 2.2 kilohms
VD: 0.6–5 Vp-p, 2.2 kilohms
Note:
The VIDEO 5 (DTV) IN jacks are not compatible with a
computer’s 5BNC (R/G/B/HD/VD) video output connectors.
AUDIO (phono jacks): 500 mVrms (100% modulation),
Impedance: 47 kilohms
SELECT OUT
VIDEO (phono jack): 1 Vp-p, 75-ohms unbalanced, sync
negative
AUDIO (phono jacks): 470 mVrms (100% modulation),
Impedance: 47 kilohms
AUDIO (VAR) OUT (phono jacks): 950 mVrms (100%
modulation)
AUDIO (FIX) OUT (phono jacks): 500 mVrms (100%
modulation)
CONTROL S IN/OUT: minijacks
Dimensions (W/H/D)
1,380 K 1,400 K 680 mm (54 3/8 K 55 1/8 K 26 7/8 inches)
(KP-57XBR10W)
1,558 K 1,574 K 735 mm (61 3/8 K 62 K 29 inches)
(KP-65XBR10W)
Mass
126 kg (277 lbs 12 oz) (KP-57XBR10W)
148 kg (326 lbs 4 oz) (KP-65XBR10W)
Supplied accessories
Remote control: RM-Y907 (1)
Batteries size: AA (R6) (2)
Optional accessories
Connecting cables:
RK-G34, RK-74A, RKG-69HG, VMC-10HG, VMC720M, VMC-810S/820S, YC-15V/30V
U/V mixer: EAC-66
Rear speakers: SS-MB115
AV receiver: STR-V555ES
Design and specifications are subject to change without
notice.
Speaker
Tweeter: 100 mm (4”) K 2
Woofer: 160 mm (6 3/8”) K 2
Center: 100 mm (4”) K 2
Speaker output
Front: 20 W K 2
Center: 20 W K 1
Rear: 20 W K 2
Power requirement
120 V AC, 60 Hz
Power consumption
In use (Max.): 300 W
In standby: 1 W
60
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02US-COV-KP57XBRUC\01COVIX.fm
Index
A
ACTIVE button . . . . . . . . . . . . 30, 32
ANT button. . . . . . . . . . . . . 26, 31, 33
Antenna cable . . . . . . . . . . . . . . . . . . 8
Antenna connector . . . . . . . . . . . . . . 8
AUDIO button . . . . . . . . . . . . . 31, 33
AUDIO menu operations 9. . . . . . . 37
Audio/Video cable . . . . . . . . . . . . . . 7
AUTO PROGRAM . . . . . . . . . . . . 42
AUTO SET UP . . . . . . . . . . . . . . . . 24
AUX Hookup . . . . . . . . . . . . . . . . . . 9
B
C
CABLE . . . . . . . . . . . . . . . . . . . . . . 42
Cable box
connection. . . . . . . . . . . . . . . . 9, 11
operation . . . . . . . . . . . . . . . . . . . 56
CAPTION VISION . . . . . . . . . . . . 45
CATV cable . . . . . . . . . . . . . . . . . . . 8
CC button . . . . . . . . . . . . . . . . . . . . 27
CH +/– buttons . . . . . . . . . . . . . . . . 26
CHANNEL CAPTION. . . . . . . . . . 41
CHANNEL FIX . . . . . . . . . . . . . . . 42
CHANNEL INDEX . . . . . . . . . . . . 33
CHANNEL SET UP menu
operations
. . . . . . . . . . . . 41
CHANNEL SKIP . . . . . . . . . . . . . . 41
Coaxial cable . . . . . . . . . . . . . . . 7, 10
COLOR. . . . . . . . . . . . . . . . . . . . . . 36
D
DAYLIGHT SAVING . . . . . . . . . . 40
Digital TV program. . . . . . . . . . . . . 28
DIRECT PLAY. . . . . . . . . . . . . . . . 46
DISPLAY button. . . . . . . . . . . . . . . 27
DRC . . . . . . . . . . . . . . . . . . . . . . . . . 1
DTV INPUT . . . . . . . . . . . . . . . . . . 47
DVD
connection. . . . . . . . . . . . . . . 18, 19
operation . . . . . . . . . . . . . . . . . . . 55
DYNAMIC PICTURE . . . . . . . . . . 37
E
Editing using SELECT OUT . . . . . 17
EFFECT . . . . . . . . . . . . . . . . . . . . . 38
;3 STEREO . . . . . . . . . . . . . . . 38
GAME. . . . . . . . . . . . . . . . . . . . . 38
LIVE . . . . . . . . . . . . . . . . . . . . . .38
;PRO LOGIC. . . . . . . . . . . . . .38
SRS 3D MONO. . . . . . . . . . . . . .38
F
Factory settings . . . . . . . . . . . . .37, 38
FAVORITE CHANNEL
selecting. . . . . . . . . . . . . . . . . . . .42
setting . . . . . . . . . . . . . . . . . . . . .43
FLASH FOCUS. . . . . . . . . . . . . . . .25
FREEZE button . . . . . . . . . .26, 31, 33
FREEZE MODE
NORMAL . . . . . . . . . . . . . . . . . .46
TWIN . . . . . . . . . . . . . . . . . . . . .46
G
G/B/R/HD/VD. . . . . . . . . . . . . .13, 47
M
MDP operation. . . . . . . . . . . . . . . . 55
Menu selection. . . . . . . . . . . . . . . . 35
MODE
GAME . . . . . . . . . . . . . . . . . 27, 36
MOVIE . . . . . . . . . . . . . . . . 27, 36
PRO . . . . . . . . . . . . . . . . . . . 27, 36
STANDARD . . . . . . . . . . . . 27, 36
VIVID . . . . . . . . . . . . . . . . . 27, 36
Movie rating. . . . . . . . . . . . . . . . . . 52
MTS
MONO . . . . . . . . . . . . . . . . . . . . 37
SAP . . . . . . . . . . . . . . . . . . . . . . 37
STEREO . . . . . . . . . . . . . . . . . . 37
MUTING button . . . . . . . . . . . . . . 26
N
NR . . . . . . . . . . . . . . . . . . . . . . . . . 37
H
Hookups. . . . . . . . . . . . . . . . . . . . . . .8
HUE. . . . . . . . . . . . . . . . . . . . . . . . .36
O
J
ON/OFF TIMER . . . . . . . . . . . . . . 40
On-line help . . . . . . . . . . . . . . . . . . 23
Operating video equipment . . . . . . 54
Joystick . . . . . . . . . . . . . . . . . . . . . .23
JUMP button . . . . . . . . . . . . . . . . . .26
P
L
LANGUAGE selection . . . . . . . . . .45
Learning menus
AUDIO . . . . . . . . . . . . . . . . . . . .37
CHANNEL SET UP . . . . . . . . . .41
SET UP . . . . . . . . . . . . . . . . . . . .44
TIMER . . . . . . . . . . . . . . . . . . . .39
VIDEO . . . . . . . . . . . . . . . . . . . .36
Additional Information
BALANCE . . . . . . . . . . . . . . . . . . . 37
BASS . . . . . . . . . . . . . . . . . . . . . . . 37
BRIGHTNESS . . . . . . . . . . . . . . . . 36
COLOR TEMP . . . . . . . . . . . . . . . . 36
Connecting Projection TV to
amplifier that supports Dolby
Pro Logic decoder. . . . . . . . . . 22
antenna . . . . . . . . . . . . . . . . . . . . . 8
audio system . . . . . . . . . . . . . . . . 21
AV receiver. . . . . . . . . . . . . . . . . 20
cable . . . . . . . . . . . . . . . . . . . . . . . 8
cable box and cable. . . . . . . . . . . . 9
camcorder . . . . . . . . . . . . . . . . . . 16
DTV receiver . . . . . . . . . . . . 12, 13
DVD Player. . . . . . . . . . . . . . 18, 19
satellite receiver . . . . . . . . . . . . . 14
satellite receiver and VCR . . . . . 15
two VCRs . . . . . . . . . . . . . . . . . . 17
VCR . . . . . . . . . . . . . . . . . . . 10, 11
CONTROL S feature . . . . . . . . . . . . 8
Convergence . . . . . . . . . . . . . . . . . . 25
CURRENT TIME . . . . . . . . . . . . . . 40
masterpage:Right
PARENTAL CONTROL. . . . . . . . 47
Password . . . . . . . . . . . . . . . . . . . . 47
PICTURE. . . . . . . . . . . . . . . . . . . . 36
PICTURE MODE button. . . . . . . . 36
Picture-and-Picture (P&P) . . . . . . . 32
Picture-in-Picture (PIP) . . . . . . . . . 30
PIP/P&P operations
ACTIVE. . . . . . . . . . . . . . . . 30, 32
ANT . . . . . . . . . . . . . . . . . . . 31, 33
AUDIO . . . . . . . . . . . . . . . . 31, 33
CH +/– . . . . . . . . . . . . . . . . . 31, 33
CHANNEL INDEX. . . . . . . . . . 33
61
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]
D:\810nouhin\4080199111\408019911KP57XBRUC\02USCOV-KP57XBRUC\01COVIX.fm
FREEZE . . . . . . . . . . . . . . . . 31, 33
POSITION . . . . . . . . . . . . . . . . . 30
SWAP . . . . . . . . . . . . . . . . . . 31, 33
TV/VIDEO . . . . . . . . . . . . . . 31, 32
Zoom in feature . . . . . . . . . . . . . 32
R
Rear speakers . . . . . . . . . . . . . . . . . . 6
Remote control
Battery installation . . . . . . . . . . . 23
Function buttons . . . . . . . . . . . . . 26
Graphic illustration. . . inside cover
S
S Video cable . . . . . . . . . . . . . . . . . . 7
Safety . . . . . . . . . . . . . . . . . . . . . . . . 2
SAP . . . . . . . . . . . . . . . . . . . . . . . . . 37
Satellite receiver operation . . . . . . . 56
Select button . . . . . . . . . . . . . . . . . . 23
SELECT OUT . . . . . . . . . . . . . . . . 45
SET UP button . . . . . . . . . . . . . . . . 24
SET UP menu operations
. . . . 44
Setting up the projection TV
automatically . . . . . . . . . . . . . 24
Printed in U.S.A
SHARPNESS . . . . . . . . . . . . . . . . . 36
SLEEP button . . . . . . . . . . . . . . . . . 27
Sliders . . . . . . . . . . . . . . . . . . . . . . . 23
SPEAKER
ALL OFF . . . . . . . . . . . . . . . . . . 38
ALL ON . . . . . . . . . . . . . . . . . . . 38
CENTER IN . . . . . . . . . . . . . . . . 38
L/R OFF . . . . . . . . . . . . . . . . . . . 38
Specifications . . . . . . . . . . . . . . . . . 60
Splitter. . . . . . . . . . . . . . . . . . . . . . . 11
SURROUND LEVEL . . . . . . . . . . . 38
SWAP button . . . . . . . . . . . . . . 31, 33
T
TEST TONE . . . . . . . . . . . . . . . . . . 39
TIMER menu operations
. . . . 39
TREBLE . . . . . . . . . . . . . . . . . . . . . 37
Troubleshooting . . . . . . . . . . . . . . . 57
TV (FUNCTION) button . . . . . . . . 26
TV POWER button . . . . . . . . . . . . . 26
TV rating . . . . . . . . . . . . . . . . . . . . . 53
TV/VIDEO button. . . . . . . . . . . . . . 27
masterpage:Left
V
X
VCR. . . . . . . . . . . . . . . . . . . . . .10, 11
VCR manufacturer code numbers . .54
VCR operation. . . . . . . . . . . . . . . . .55
VIDEO LABEL. . . . . . . . . . . . . . . .46
VIDEO menu operations
. . . . .36
VOL +/– buttons . . . . . . . . . . . . . . .26
XDS . . . . . . . . . . . . . . . . . . . . . . . . 27
Y
Y/PB/PR. . . . . . . . . . . . . . . . . . . 12, 19
W
WIDE MODE button. . . . . . . . . . . .29
WIDE SCREEN MODE
FULL. . . . . . . . . . . . . . . . . . . . . .29
NORMAL . . . . . . . . . . . . . . . . . .29
Wide screen mode . . . . . . . . . . . .28
WIDE ZOOM . . . . . . . . . . . . . . .29
ZOOM . . . . . . . . . . . . . . . . . . . . .29
WIDE SCREEN MODE menu
operation
. . . . . . . . . . . .40
If, after reading this instruction manual, you
have additional questions related to the use of
your Sony projection TV, please call one of the
following numbers (English only).
Customers in the continental United
States contact the Sony Customer
Information Service Center at:
1-800-222-SONY (7669)
Customers in Canada contact the
Sony Customer Relations Center at:
(416) 499-SONY (7669)
Model name1[KP-57XBR10W] Model name2[KP-65XBR10W]
[4-080-199-11 (1)]