advertisement
Portable
MiniDisc Player
Operating Instructions
3-266-437-11(1)
“WALKMAN” is a registered trademark of Sony Corporation to represent Headphone Stereo products. trademark of Sony Corporation.
is a
MZ-NF520D
© 2004 Sony Corporation
2
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
To prevent fire, do not cover the ventilation of the apparatus with news papers, table cloths, curtains, etc. And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
Certain countries may regulate disposal of the battery used to power this product.
Please consult with your local authority.
Caution
The use of optical instruments with this product will increase eye hazard.
CAUTION
—
CLASS 1M INVISIBLE
LASER RADIATION WHEN OPEN
DO NOT VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS
Information
IN NO EVENT SHALL SELLER BE
LIABLE FOR ANY DIRECT,
INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR
EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR
THE USE OF ANY PRODUCT.
For customers who purchased this product in the USA
Owner’s Record
The serial number is located at the rear of the disc compartment lid and the model number is located at the top and bottom.
Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. MZ-NF520D
Serial No.
Product registration
Please register this product on line at www.sony.com/walkmanreg
<http://www.sony.com/walkmanreg>
Proper registration will enable us to send you periodic mailings about software upgrades, new products, services and other important announcements. Thank you.
If you have any questions about this product, contact:
— http://www.sony.com/ walkmansupport
— Sony Network Portable Audio
Support Line
1-(866)-456-7669
— Sony Customer Information
Services Center
12451 Gateway Blvd. Fort Myers,
FL 33913
Declaration of Conformity
Trade Name: SONY
Model No.: MZ-NF520D
Responsible Party: Sony Electronics
Inc.
Address: 16450 W. Bernardo Dr, San
Diego, CA 92127 USA
Telephone No.: 858-942-2230
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
3
4
Notice for users
On the supplied software
• Copyright laws prohibit reproducing the software or the manual accompanying it in whole or in part, or renting the software without the permission of the copyright holder.
• In no event will SONY be liable for any financial damage, or loss of profits, including claims made by third parties, arising out of the use of the software supplied with this player.
• In the event a problem occurs with this software as a result of defective manufacturing, SONY will replace it.
However, SONY bears no other responsibility.
• The software provided with this player cannot be used with equipment other than that which is so designated.
• Please note that, due to continued efforts to improve quality, the software specifications may be changed without notice.
• Operation of this player with software other than that provided is not covered by the warranty.
Notes
• The recorded music is limited to private use only. Use of the music beyond this limit requires permission of the copyright holders.
• Sony is not responsible for music files that cannot be saved on your computer due to unsuccessful recording from a CD or from music downloading.
On the battery
• When you replace the battery, be sure to use a new one.
• If “LoBATT” appears even once in the display, replace the battery.
• SonicStage, MD Simple Burner,
OpenMG, Magic Gate, MagicGate
Memory Stick, Memory Stick, Net MD,
ATRAC, ATRAC3, ATRAC3plus and their logos are trademarks of Sony
Corporation.
• Microsoft, Windows, Windows NT and
Windows Media are trademarks or registered trademarks of Microsoft
Corporation in the United States and /or other countries.
• IBM and PC/AT are registered trademarks of International Business
Machines Corporation.
• Macintosh is a trademark of Apple
Computer, Inc. in the United States and/ or other countries.
• MMX and Pentium are trademarks or registered trademarks of Intel
Corporation.
• All other trademarks and registered trademarks are trademarks or registered trademarks of their respective holders.
• ™ and ® marks are omitted in this manual.
CD and music-related data from
Gracenote, Inc., copyright © 2000-2003
Gracenote. Gracenote CDDB R Client
Software, copyright 2000-2003
Gracenote. This product and service may practice one or more of the following U.S.
Patents: #5,987,525; #6,061,680;
#6,154,773, #6,161,132, #6,230,192,
#6,230,207, #6,240,459, #6,330,593 and other patents issued or pending.
Gracenote and CDDB are registered trademarks of Gracenote. The Gracenote logo and logotype, the Gracenote CDDB logo, and the “Powered by Gracenote” logo are trademarks of Gracenote.
Program © 2001, 2002, 2003, 2004
Sony Corporation
Documentation © 2004 Sony Corporation
5
6
Table of contents
Player Operation
Looking at the controls .................................. 12
Getting started! .............................................. 16
Playing an MD right away! .............................. 18
Listening to the radio ..................................... 20
Various ways of playback .............................. 22
Viewing various information ................................................................22
Selecting the play mode ........................................................................22
Playing a track repeatedly (Repeat Play) ........................................23
Adjusting treble or bass (Digital Sound Preset) ....................................23
Selecting the sound quality .............................................................23
Adjusting the sound quality ............................................................24
Using the group function ................................ 25
What is the group function? ..................................................................25
Playing a track in group play ..........................................................26
Selecting the play mode for group play (Group Play Mode) .........26
Repeat play for the selected group play mode
(Group Repeat Play) ........................................................26
Other Operations ............................................ 27
How to use the menu items ............................................................29
Selecting the play mode ..................................................................30
Adjusting treble or bass (Digital Sound Preset) .............................31
Starting the playback quickly (Quick Mode) .................................32
Protecting your hearing (AVLS) ....................................................32
Viewing various information ..........................................................33
Locking the controls (HOLD) ...............................................................34
Various way to use the radio ......................... 35
Presetting radio stations ....................................................................... 35
Listening to the preset radio stations .................................................... 35
Additional information .................................... 36
Troubleshooting and explanations ................ 39
Troubles and solutions ......................................................................... 39
While playing ................................................................................. 39
While using group function ........................................................... 40
While using the radio ..................................................................... 40
7
8
Software Operation
What you can do with MD Simple Burner/
SonicStage ...................................................... 44
What you can do with MD Simple Burner .....................................44
What you can do with SonicStage ..................................................44
Basic operational flow using an MD Walkman .............................45
Installing ......................................................... 46
Providing the required system environment .........................................46
System requirements ......................................................................46
Installing the software onto your computer ..........................................47
Connecting the MD Walkman to your computer ..................................48
Using MD Simple Burner ................................. 49
Recording by computer operations .......................................................49
The window for recording all tracks on the CD .............................49
The window for recording selected tracks from an audio CD ........50
Using SonicStage ........................................... 51
Importing audio data .............................................................................51
Transferring audio data from your computer to the MD Walkman ......53
Transferring from the MD Walkman back to your computer ........55
Using SonicStage Help .........................................................................57
To display SonicStage Help ...........................................................57
Understanding SonicStage Help .....................................................58
Searching for a word inside an explanation ...................................58
Referring to SonicStage Help ...............................................................59
Importing audio data to the computer ............................................59
Listening to audio data on the computer ........................................59
Managing and editing imported tracks ...........................................59
Backing up audio data ....................................................................60
Troubleshooting ..............................................................................60
When you want to know .................................................................60
Other information ........................................... 61
Uninstalling SonicStage/MD Simple Burner ....................................... 61
On copyright protection ....................................................................... 62
The software cannot be installed onto your computer ................... 64
Using a MD Walkman connected to the computer ........................ 65
9
10
Before using this product
This manual explains the player operations and the installation and basic use of the supplied software.
For details on the various operations, refer to the pages indicated below.
When using the player
Player Operation (pages 11 to 42)
Pages 11 to 42 in this manual explain all of the player functions.
Troubleshooting and explanations (page 39)
This section shows the troubles you may find while using the player, and their solutions.
_________
______________________________
When using the Net MD (the player) connected to your computer
Software Operation (pages 44 to 65)
Pages 44 to 65 in this manual explain the installation and basic operations of the supplied
SonicStage and MD Simple Burner software.
This section shows the troubles you may find while using the supplied SonicStage software, and their solutions. It also has the list of frequently asked questions and answers.
SonicStage Ver. 2.0 Help
This is a help that you can view on your computer screen.
Refer to Help for details on the use of the software. To display
Notes on the “Software Operation” section
• The displayed items in the illustrations that appear in this section may differ from the actual items displayed by the software.
• Explanations in this section assume familiarity with basic Windows operations. For details on the use of your computer and the operating system, please refer to the respective manuals.
• Explanations in this section cover general Net MD products. For this reason, some explanations (and some illustrations) may not be applicable to your Net MD. Please refer to the operating instructions of your Net MD as well.
Checking the supplied accessories
Headphones with a remote control (1)
(for USA model)
Earphones with a remote control (1)
(for Canadian model)
Dedicated USB cable (1)
CD-ROM (SonicStage Ver. 2.0 and MD Simple Burner Ver. 2.0) (1)*
Recordable disc (1)
∗
Do not play a CD-ROM on an audio CD player.
11
12
Looking at the controls
Front of the player
3
1
2
4
5
6
7
8
A Display window
B VOLUME +* and – button
∗
The VOLUME + button has a tactile dot.
C 4-position control key
ENTER/NX (enter/play/pause)*
. and > (search/AMS) x/CANCEL (stop/cancel)
∗
The ENTER/NX button has a tactile dot.
D MENU button
E GROUP button
F USB jack
When connecting to your computer, connect the dedicated USB cable to this jack.
G HOLD switch
H i (headphones/earphones) jack
Back of the player
2
3
1
A OPEN button
B Hand strap hole
Use the hole to attach your own strap.
C Battery compartment lid
The display window of the player
1
2
3
4
5
6
7
8
A Disc indication
B Group mode indication
Lights up when group mode is on.
C Track number display
D Battery level indication
Shows approximate battery condition.
E Play mode indication
Shows play mode of the MD.
F SOUND indication
G Disc, group, track indication
H Character information display
Displays the track names, elapsed time, etc.
13
14
The headphones/earphones with a remote control
A
B
C
D
E
F
G
H
I
J
K
A VOL +, – buttons
Press to adjust the volume.
B Jog lever (. • NX/ENT • >,
TUNE – • BAND • TUNE +)
NX/ENT (to press): play, pause, enter
.(to slide towards): REW
> (to slide towards): FF
BAND (to press): select a band
TUNE – (to slide towards): tune backward
TUNE + (to slide towards): tune forward
C Display window
D x (stop) button
E (group) +, – buttons
F RADIO ON/OFF button
Press to turn on or off the radio.
G Clip
H HOLD switch
To prevent the buttons from being accidentally operated when you carry the player, use this function.
I DISPLAY button
J P-MODE/
button
K SOUND button
The display window of the remote control
A B C D E
F G
A Disc indication
B PRESET indication
C Character information display
D Play mode indication
E SOUND indication
F Battery level indication
G Track number/Band/Preset number display
15
Getting started!
1
Insert an alkaline dry battery.
16
E e
Slide to open the battery compartment lid.
Insert one LR6 (size AA) alkaline dry battery minus end first.
Close the lid.
When to replace the battery
You can check the battery condition through the battery indicator while using the player.
Battery power decreasing r
Weak battery r
The battery has gone out.
“LoBATT” flashes in the display, and the power goes off.
Battery life 1)
When playing 2) transferring audio data from the computer 3)
SP Stereo LP2 Stereo LP4 Stereo
Approx. 36 hours Approx. 42.5 hours Approx. 48 hours
55 tracks (of about
5 minutes each)
230 tracks (of about
5 minutes each)
325 tracks (of about
5 minutes each)
1) When using a new Sony LR6 (size AA) alkaline dry battery (produced in Japan).
2) Measured in accordance with the JEITA (Japan Electronics and Information Technology Industries
3)
Association) standard.
The numbers of tracks that can be transferred differs according to the computer’s operating environment.
When using the radio
FM TV/Wb(weather)(USA model only)
Approx. 18.5 hours Approx. 17 hours
Notes
• Disconnect the dedicated USB cable before replacing the dry battery.
• The battery life may be shorter than that specified, depending on the operating conditions, the temperature of the location, and varieties of batteries.
• When you replace the battery, be sure to use a new one.
• If “LoBATT” appears even once in the display, replace the battery.
2
Make connections and unlock the controls.
1 Connect the headphones/earphones
with the remote control to i.
2 Slide HOLD in the opposite direction of the arrow indicated on the player
(HOLD .) to unlock the control.
HOLD
to i
Connect firmly.
17
Playing an MD right away!
1
Insert an MD.
1
Press OPEN to open the lid.
2
Insert an MD to the direction of the arrow with the label side facing front, and press the lid down to close.
18
2
Play an MD.
4-way control key
(NX, ., >, x)
VOLUME +, –
VOL +, –
Jog lever
(NX,
.
,
> ) x
1 Press NX on the player.
(Press the jog lever (NX) on the remote control.)
2 Press VOLUME + or – to adjust the volume.
(Press VOL + or – on the remote control.)
The volume will be shown in the display.
To stop play, press x .
After you stop the player, the player will automatically turn off in about 10 seconds.
Playback starts from the point you last stopped playing.
To start with the first track of the disc, press
NX on the player or the jog lever (NX) on the remote control for 2 seconds or more.
To
Pause
Cue to the current track or the previous track
Operation on the player Operation on the remote control
Press NX . Press NX again to resume play.
Press the jog lever (NX).
Press the jog lever (NX) again to resume play.
Press ..
Press . repeatedly.
Slide the jog lever towards
.. Slide the jog lever towards . repeatedly.
Cue to the next track
Go backwards or forward while playing
Press >.
Slide the jog lever towards
>.
Press and hold . or >.
Slide and hold the jog lever towards . or >.
Search for a specific position while viewing a elapsed time
(Time Search)
Search for a specific track while viewing track names and numbers
(Index Search)
Press and hold . or > while pausing.
Press and hold . or > while the player is stopped.
Slide and hold the jog lever towards . or > while pausing.
Slide and hold the jog lever towards . or > while the player is stopped.
Cue to the beginning of the every 10th track
(only during playback of the disc with no group settings 1) )
Remove the MD
Press GROUP, and then press
. or >.
Press x and open the lid.
2)
Press + or – button
Press x and open the lid.
1)
For more details, see “Using the group function” (page 25).
2) Once you open the lid, the point to start play will change to the beginning of the first track.
Suppressing the skip of the sound (G-PROTECTION)
The G-PROTECTION function was developed to provide a higher level of shock resistance than that of existing players in order to allow the player to be used while jogging.
Note
The playback sound may skip if:
• the player receives stronger continuous shock.
• a dirty or scratched MiniDisc is played.
z
• The MZ-NF520D supports DSP TYPE-S for ATRAC/ATRAC3. It thus allows you to enjoy TYPE-S high-quality sound from MDs recorded in MDLP mode on TYPE-S-equipped MD decks, etc.
• The player can play the track recorded by 2
×
or 4
× long playing mode (LP2 or LP4). Normal stereo playback, LP2 stereo playback, LP4 stereo playback or monaural playback is automatically selected to match the audio source.
19
20
Listening to the radio
You can listen to the FM broadcast through the built-in digital tuner in the remote control. With the USA model, you can also listen to TV and weather broadcasts.
Controls on the player cannot be used to operate the tuner.
1
Turn on the radio.
VOL +, –
Jog lever
(BAND, TUNE –,
TUNE +) x
RADIO ON/OFF
P-MODE/
SOUND
1 Press RADIO ON/OFF.
The radio turns on.
If “ PRESET ” is displayed, press P-
MODE/ the display.
to make it disappear from
2 For the USA model, press the jog lever repeatedly to select the band.
Each time you press the jog lever, the indication changes as follows:
“FM” t“TV”t“Wb”(weather)
For the Canadian model, only the FM band can be received. You cannot select other bands.
3
Slide the jog lever towards TUNE + or
TUNE – repeatedly to tune in the desired radio station.
4 Press VOL +, – to adjust the volume.
To turn off the radio
Press RADIO ON/OFF or x.
To tune in a station quickly
(FM only)
In step 3, slide and hold the jog lever until the frequency indication begins to change.
The remote control automatically scans the radio frequencies and stops when it finds a clear station.
To improve the broadcast reception
Extend the headphones/earphones cord, which act as the FM antenna.
If an FM broadcast is hard to tune in
Press SOUND repeatedly until “Local” appears in the display. The noise will be reduced.
When you cannot operate the radio
Make sure the remote control is not
Notes
• The radio will not operate if the remote control is not connected to the player.
• The volume of radio and MD can be adjusted individually using the supplied remote control.
• Playback stops when you use the radio.
• Do not place the remote control close to another electronic device, such as the player itself, another radio, a TV, a mobile phone, or a computer, as this may cause noise in the reception.
• When you use the radio, it is recommended that you use a new dry battery since more power is consumed by the radio than by MD playback.
21
Various ways of playback
In this section, the operation using the remote control is mainly explained. For details on operations done on the player, see the pages indicated for each operation.
Notes
• Depending on whether group play or normal play is selected, the operating conditions, and the disc settings, you may not be able to select certain indications or the indications may appear differently.
• During playback, the track mode appears momentarily, and is then replaced by the elapsed time of the current track.
Viewing various information
You can check the track or disc name, track number, the elapsed playing time of the current track, the number of the tracks recorded on the MD, the group name, and the total number of tracks in a group.
For the player operation, see page 33.
DISPLAY
Selecting the play mode
You can select from the various play modes using the P-MODE/ button.
P-MODE/
1
While playing, press DISPLAY.
Each time you press DISPLAY, the display changes as follows:
Display window on the remote control
A B
Jog lever
1
Press P-MODE/ repeatedly.
Each time you press the button, the play mode changes as follows:
Display window on the remote control
Play mode indication
22
Display: A / B
A B
Track number
Track number
The number of total tracks in the group
The number of total tracks
Track number
The elapsed time
Track name
Group name
Disc name
Track mode
Indication 1)
(none)
(normal play)
Play mode
All the tracks are played once.
1 (single-track play)
A single track is played once.
SHUF
(shuffle play)
All the tracks are played in random order.
1) Group play mode ( ) appears whenever you play a disc with group settings. For more
details, see “Selecting the play mode for group play (Group Play Mode)” (page 26).
For the player operation, see page 30.
Playing a track repeatedly
(Repeat Play)
You can use the repeat function for normal play, single-play, and shuffle play mode.
1
During playback in the selected play mode, press and hold P-MODE/ for 2 seconds or more.
appears in the display.
To cancel repeat play
Press and hold P-MODE/ for 2 seconds or more.
z
By pressing P-MODE/ button during repeat play, you can change the play mode to be used with repeat play.
For the player operation, see page 30.
Adjusting treble or bass
(Digital Sound Preset)
You can adjust the treble and bass to suit your taste. The player can store two sets of treble-bass adjustments, which can then be selected later during playback.
Jog lever
SOUND
Selecting the sound quality
Factory settings
Factory settings of the Digital Sound
Preset are as follows:
• “SOUND1”: bass +1, treble ±0
• “SOUND2”: bass +3, treble ±0
1
Press SOUND repeatedly to select
“SOUND1” or “SOUND2” in the display.
To cancel Digital Sound Preset
23
24
Adjusting the sound quality
You can change the preset sound quality and store the results in “SOUND1” or
“SOUND2”.
1
Press SOUND repeatedly to select
“SOUND1” or “SOUND2”.
2
During playback, press SOUND for 2 seconds or more.
The player changes to B (bass) setting mode. Pressing jog lever changes the player to T (treble) setting mode.
When you select bass-setting mode,
“B” appears. When you select treble setting mode, “T” appears.
3
Slide the jog lever repeatedly to adjust the level.
Example: While adjusting the bass
The cursor moves.
(Position: –2)
4
Press the jog lever to enter.
The sound settings are saved and the playback display appears again.
To cancel the setting
Press SOUND repeatedly until nothing
appears in the display in step 1.
To cancel the procedure
Press and hold the DISPLAY button or x button for 2 seconds or more.
For the player operation, see page 31.
z
• Settings can also be changed while playback is momentarily paused (X).
• If the player is not operated approximately for
3 minutes, the current setting is stored and the display automatically switches to normal playback.
Note
When you use the Digital Sound Preset, the sound may break or become distorted depending on the settings or the track. In this case, change the settings of the sound quality.
–4 ±0 +3
The sound can be adjusted in 8 steps
(–4, –3, ...±0, ...+2, +3).
To switch “B” (bass) and “T”
(treble):
Press the jog lever.
To switch “SOUND1” and
“SOUND2”:
Press SOUND.
Using the group function
What is the group function?
The group function is provided to allow playback of discs with group settings. The group function is convenient for playback of MDs on which several albums or CD singles have been recorded in MDLP
(LP2/LP4) mode.
What is a disc with group settings?
The player can operate various functions in units of group; that is tracks that have been recorded on a disc as part of separate groups, as shown below.
Before group settings are made
Disc
Note
The player does not support the recording of group settings on the player. Use the supplied
SonicStage software to assign tracks to group.
For details, see “Software Operation” section
MENU
GROUP
ENTER/NX,
.
, >, x/
CANCEL
Playing groups
The player can operate various playback with a disc which has group setting.
This section explains the operations that are done on the remote control. For details
on operations on the player, see page 30
1 2 3 4 5 6 7 8 12131415 m
Track 1 to 5 are assigned to group 1.
Track 8 to12 are assigned to group 2.
Track 13 to15 are assigned to group 3.
Track 6 to 7 are assigned to no group.
After setting the group (group play)
Disc
Group 1 Group 2 Group 3
1 2 3 4 5 6 7 1 2 3 4 5 1 2 3
Tracks that were not assigned to a group are treated as being part of “GP --”.
You can create a maximum of 99 groups on a disc.
Jog lever
+, –
P-MODE/
25
26
Playing a track in group play
In group play, all groups are played in order, starting with group 1, followed by the unassigned tracks (“Group - -”).
Playback stops after all the tracks have been played.
1
During playback, press P-MODE/ repeatedly until “ ” appears in the display.
To cue to the start of a group
(Group Skip)
1 During playback, press + or –.
Pressing – button cues to the first track in the current group. Pressing the button again cues to the first track of the previous group.
For the player operation, see page 30.
Selecting the play mode for group play (Group Play Mode)
The shuffle play and repeat play function can be used during group play mode.
1
Press P-MODE/ repeatedly.
After normal playback (page 22), the
following play modes are displayed.
Display
(Normal
Group Play)
, SHUF
(In-Group
Shuffle)
Play mode
All tracks in the groups play back once (starting with the first track in group 1).
Shuffle play starts with the group that is currently playing, and continues with the succeeding groups.
Repeat play for the selected group play mode
(Group Repeat Play)
1
During playback in the selected group mode, press and hold P-MODE/ for 2 seconds or more.
“ ” appears in the display.
Playback repeats in the respective group play mode.
Display Play mode
Repeat play of tracks within a group
SHUF Repeat shuffle play of tracks within a group
Other Operations
Useful settings
The player has various useful functions for playback.
The following table shows the functions that you can select. Some items can be set by menu operations on both the player and the remote control, while others can be set with the buttons on the remote control.
Category
Playing
Display
Function
Selecting the play mode
Changing the sound quality
Starting playback quickly
Limiting the maximum volume
Viewing information
What it does
Selects the play mode, such as repeat play, shuffle play, etc.
Adjust the treble and bass, and stores two sets of treble-bass adjustment.
player remote control player Sets the player to start playback or cue to a track quickly.
remote control
Sets a limit on the maximum volume to protect your hearing.
Displays various information such as the remaining time, etc. in the display window.
Operation player remote control player remote control player remote control
Site page
page 32 page 32 page 32 page 32
This section mainly explains the settings made by menu operations on the player.
27
28
List of menus
Menus on the player
Items listed under “Menu 1” are the selectable items which appear when you press MENU, items listed under “Menu 2” are the selectable items which appear when you select an item in Menu 1, and “Menu 3” are the selectable items which appear when you select an item in
Menu 2.
Note
Different indication may be displayed depending on the operating conditions and settings.
Menu 1 Menu 2
DISP LapTim
T:Name
G:Name
D:Name
T–MODE
P-MODE Normal
1 Trk
SOUND
OPTION
Shuff
Normal
Shuff
OFF
SOUND1
SOUND2
SET
AVLS
Power
Menu 3
—
—
—
—
—
RepOFF (factory setting) y RepON
—
—
—
SOUND1 y SOUND2
OFF (factory setting) y ON
NORMAL (factory setting) y QUICK
Menu on the remote control
Menu 1 Menu 2 Functions
OPTION AVLS AVLS OFF (factory setting) y AVLS ON
PowerMode NORMAL (factory setting) y QUICK
How to use the menu items
To set the menu items, do the following procedure.
On the player
1 Press MENU to enter the menu.
2 Press . or > to select the item.
3 Press ENTER to enter the selection.
4
The setting will be entered when you press
ENTER at the last.
To return the preceding setting
Press x.
To cancel the operation while setting
Press and hold x for 2 seconds or more.
MENU
4-position control key
On the remote control
You can set only the “OPTION” menu.
1 Press and hold DISPLAY for 2 seconds or more to enter the menu.
2 Press the jog lever.
3 Slide the jog lever to select the item.
4 Press the jog lever to enter the selection.
5
The setting will be entered when you press the jog lever at the last.
To return the preceding setting
Press x.
To cancel the operation while setting
Press and hold x for 2 seconds or more.
Jog lever
DISPLAY
29
30
Selecting the play mode
For details and remote control operation,
1
While the player is playing, enter the menu and select “P-MODE”.
2
Select the desired play mode.
Each time you press >, the display item indicated by A changes as follows:
Pressing ENTER/NX while A is flashing causes the play mode to enter.
Pressing > repeatedly changes A .
Display A 1)
Normal
(normal play)
1 Trk
(single-track play)
Shuff
(shuffle play)
Play mode
All the tracks are played once.
A single track is played once.
All the tracks are played in random order.
1) Group play mode ( ) appears whenever you play a disc with group settings. For more
details, see “Playing a track in group play”
3
Press . or > repeatedly until
“RepOFF” or “RepON” (playing a track repeatedly) appears in the display, and then press ENTER/NX to enter the selection.
If you select “RepON”, “ ” appears on B and the playback repeats with
the play mode selected in step 2.
B lights up when you press ENTER/
NX .
Display B Play mode
Repeat play of all tracks
1
SHUF
Repeat play of a selected track
Repeat shuffle play of all tracks
To cancel the procedure
Press MENU .
To return the preceding settings
Press x/CANCEL.
Playing a track in group play
1
Do steps 1 and 2 of (“Selecting the play mode”, page 30) and select
“ Normal ”
To cue to the start of a group (Group
Skip)
1 Press GROUP.
2 While “ ” flashing, press . or >.
Pressing . button cues to the first track in the current group. Pressing the . button again cues to the first track of the previous group.
For the remote control operation, see
Selecting the play mode for group play (Group Play Mode)
1
Do steps 1 to 2 of “Selecting the play mode” (page 30).
After normal playback (page 22), the
following play modes appears after normal play.
Display
, Normal
(Normal
Group Play)
Play mode
All tracks in the groups play back once (starting with the first track in group 1).
, Shuff
(In-Group
Shuffle)
Shuffle play starts with the group that is currently playing, and continues with the succeeding groups.
2
Select “RepON” or “RepOFF”.
For the remote control operation, see
Adjusting treble or bass
(Digital Sound Preset)
Selecting the sound quality
1
Enter the menu and select “SOUND”
- “SOUND1” or “SOUND2”.
To cancel Digital Sound Preset
Select “OFF”.
Adjusting the sound quality
1
Enter the menu and select “SOUND”
- “SET”.
2
Press . or > repeatedly until
“SOUND1” or “SOUND2” appears in the display, and then press ENTER/
NX.
The display shows the currently
“BASS” sound setting.
3
Press . or > repeatedly to adjust the sound level.
Shows “SOUND1” or
“SOUND2” is selected
The sound can be adjusted in 8 steps.
(–4, –3, ...±0, ...+2, +3)
4
Press ENTER/NX.
“BASS” is set and the display changes to “TRE” (treble) setting mode.
5
Press . or > repeatedly to adjust the sound level, and then press
ENTER/NX to enter the selection.
“TRE” (treble) is set.
The sound settings are saved and the playback display appears again.
To cancel the procedure
Press MENU.
To return the preceding settings
Press x/CANCEL.
For the details and the remote control
31
32
Starting the playback quickly
(Quick Mode)
After pressing the playback button or cueing to the track, the playback can start quickly.
1
Enter the menu and select “OPTION”
- “Power”(“PowerMode” on the remote control).
2
Select “QUICK”.
Display window on the player
Display window on the remote control
To switch back to the normal setting
To cancel the procedure
Press MENU.
To return the preceding settings
Press x/CANCEL.
Notes
• When the power mode is set to “QUICK”, the power remains on within the player even when nothing appears in the display. This leads to a shorter battery life.
• If no player operation (including opening or closing of the lid) occurs for an hour, the power in the player automatically turn off. For this reason, the next time you start playback or do another operation, the player will not respond quickly. the unit, however, will return to quick mode afterwards.
Protecting your hearing
(AVLS)
The AVLS (Automatic Volume Limiter
System) function sets a maximum volume level to protect your ears.
1
Enter the menu and select “OPTION”
- “AVLS”.
2
Select “ON”.
When you try to turn the volume too high, “AVLS” appears in the display.
The volume is kept to a moderate level.
To cancel the AVLS
To cancel the procedure
Press MENU.
To return the preceding settings
Press x/CANCEL.
Viewing various information
A B
Track number —
Track number
C
The elapsed time
Track name
The number of total tracks in the group
GP
The number of total tracks
Track number —
Group name
Disc name
Track mode
1
While playing, enter the menu and select “DISP”.
2
Select the information you want.
Each time you press . or >, the display changes as the follows:
Display
LapTim
T:Name
G:Name
D:Name
T–MODE
Meaning
The elapsed time of the current track
Track name
Group name
Disc name
Indicates the recording mode selected on the MD player used; i.e., “SP”,
“LP2”, “LP4”, or
“MONO”.
Notes
• Depending on the group settings, the operating conditions and the disc settings, you may not be able to select certain indications or the indications may appear differently.
• The “T–MODE” indication appears only during playback. It appears for a few seconds, and is then replaced by the elapsed time of the current track.
For the details and the remote control
33
34
Locking the controls
(HOLD)
To prevent the buttons from being accidentally operated when you carry the player, use this function.
HOLD
1
Slide HOLD in the direction of the
. to lock.
To unlock the controls
Slide HOLD to the opposite direction of the arrow.
Various way to use the radio
Presetting radio stations
For the USA model, up to 41 radio stations can be preset, 30 for FM, 7 for
TV, and 4 for Wb (weather).
For the Canadian model, up to 30 FM stations can be preset.
RADIO ON/OFF
P-MODE/
6
Press the jog lever to enter the selection.
A long beep sounds in the headphones/earphones. “PRESET”,
“M”, and preset number disappear in the display.
Listening to the preset radio stations
You can simply tune the station by selecting the preset number.
RADIO ON/OFF
P-MODE/
Jog lever
(BAND, TUNE –, TUNE +)
1
Press RADIO ON/OFF to turn on the radio.
If “PRESET” is displayed, press P-
MODE/ to make it disappear from the display.
2
Press the jog lever repeatedly to select the band.
USA model: “FM” t “TV” t “Wb
(weather)”
Canadian model: “FM” only
3
Slide the jog lever towards TUNE + or TUNE – repeatedly to tune the desired radio station.
4
Press and hold the jog lever until
“M” and the preset number flash in the display.
5
Slide the jog lever repeatedly until the desired preset number appears in the display.
Jog lever
(BAND, TUNE –, TUNE +)
1
Press RADIO ON/OFF to turn on the radio.
2
Press the jog lever repeatedly to select the band.
USA model: “FM” t “TV” t “Wb
(weather)”
Canadian model: “FM” only
3
Press P-MODE/ so that
“PRESET” appears in the display.
4
Slide the jog lever towards TUNE + or TUNE – repeatedly until the desired preset number appears in the display.
Note
In the case of double-digit preset numbers, the band is indicated in the display by “F” for FM.
35
36
Additional information
Precautions
On safety
• Do not carry or store the dry battery in the same place with metallic objects such as coins, key rings, or necklaces. This may cause a short-circuit and the generation of heat.
• Incorrect battery usage may cause the battery fluid to leak or battery to burst. To prevent such accidents, make sure the battery is installed with the + and – poles oriented correctly.
• If a battery leak should develop, carefully and thoroughly wipe away the battery fluid in the battery compartment before inserting a new battery.
• If you will not use the player for a long time, be sure to remove the dry battery.
On Handling
• Do not drop or bump the player. This may cause the player to malfunction.
• Do not pull headphones/earphones cords.
• Do not place the player in the following places:
—An extremely hot place (over 60°C
(140°F))
—A place exposed to direct sunlight or near a heater
—In a car with the windows rolled up
(especially in the summer)
—In a damp place such as a bathroom
—Near a source of electromagnetic fields such as a magnet, speaker, or TV
—In a dusty place
On heat build-up
Heat may build up in the player if it is used for an extended period of time. This, however, is not a malfunction.
On mechanical noise
The player emits mechanical noise while operating, which is caused by the power-saving system of the player. This is not a malfunction.
On installation
Never use the player where it will be subjected to extremes of light, temperature, moisture or vibration.
On the MiniDisc cartridge
• Do not touch the internal disc directly. Forcing the shutter open may damage the internal disc.
• When transporting a MiniDisc, keep it in its case.
• Do not place the cartridge where it will be subjected to light, temperature, moisture or dust.
• Do not affix the label outside of the specified area on the MD. Make sure the label is placed within the recessed space on the disc.
On the headphones/earphones
Road safety
• Do not use headphones/earphones while driving, cycling, or operating any motorized vehicle. This may lead to a traffic accident and is illegal in many areas. It can also be potentially dangerous to play your player at high volumes while walking, especially at pedestrian crossings. You should exercise extreme caution or discontinue using the player in potentially hazardous situations.
• If you experience an allergic reaction to the supplied headphones/earphones, stop using them at once and consult a doctor or a Sony service center.
Preventing hearing damage
Avoid using headphones/earphones at high volumes. Hearing experts advise against continuous, loud and extended play. If you experience a ringing in your ears, reduce the volume or discontinue use.
Caring for others
Keep the volume at a moderate level. This will allow you to hear outside sounds and to be considerate of the people around you.
On cleaning
• After wiping the player casing with a soft cloth slightly moistened with water, wipe it again with a dry cloth. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzene as this may mar the finish on the casing.
• Wipe the disc cartridge with a dry cloth to remove dirt.
• Dust on the lens may prevent the unit from operating properly. Be sure to close the disc compartment lid after inserting or ejecting an
MD.
• To maintain good sound quality, use a soft cloth to clean the plugs of the headphones/ earphones. A dirty plug may cause noise or intermittent breaks in the sound during playback.
• Clean the terminals periodically with a cotton swab or a soft cloth as illustrated.
Dry battery compartment
If the power source (battery) accidentally becomes disconnected during recording
The lid may refuse to open. If this happens, do not open the lid by force. Do the steps below instead.
1 Connect the power source (battery) firmly to the player.
2 Press the OPEN button to open the lid.
To protect a recorded MD
To record-protect an MD, slide open the tab at the side of the MD. In this position, the MD cannot be recorded. To record again, slide the tab back so the tab is visible.
Tab
Back of the MD
Recorded material is protected.
Terminals
When recording with the supplied application software
Before you remove the MD after the transfer of audio data from your computer has completed
Make sure that “TOC Edit” has disappeared in the display, and then press the x (stop) button.
Recorded material is not protected.
If you have any questions or problems concerning your player, please consult your nearest Sony dealer. (If a trouble occurred when the disc was in the player, we recommend that the disc be left in the player when you consult your Sony dealer so that the cause of trouble may be better understood.)
When consulting your Sony dealer, be sure to bring the player and the headphones/earphones.
37
Specifications
MD Player
Audio playing system
MiniDisc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength:
λ
= 790 nm
Emission duration: continuous
Laser output: less than 44.6 µW
(This output is the value measured at a distance of 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.)
Recording and playback time (when using MDW-80)
Maximum 160 min. in monaural
Maximum 320 min. in LP4 stereo
Revolutions
Approx. 380 rpm to 2,700 rpm
Error correction
ACIRC (Advanced Cross Interleave Reed
Solomon Code)
Sampling frequency
44.1 kHz
Coding
ATRAC (Adaptive TRansform Acoustic
Coding)
ATRAC3 — LP2/LP4
Modulation system
EFM (Eight to Fourteen Modulation)
Number of channels
2 stereo channels
1 monaural channel
Frequency response
20 to 20,000 Hz ± 3 dB
Outputs i : stereo mini-jack, maximum output level
5 mW + 5 mW, load impedance 24
Ω
(USA)
5 mW + 5 mW, load impedance 16
Ω
(Canada)
38
Radio
Frequency range
USA model:
FM: 87.5 - 108.0 MHz
TV: 2 - 13 CH
WEATHER: 1 - 7 CH
Canadian model:
FM: 87.5 - 108.0 MHz
Antenna
FM/TV/WEATHER:
Headphones/earphones cord antenna
General
Power requirements
One LR6 (size AA) alkaline battery (not supplied)
Recommended temperature for check-in/check-out
+5
°
C (+41
°
F) or higher
Battery operation time
Dimensions
Approx. 81
×
30.7
×
74.4 mm (w/h/d) (3 1 /
4
×
1 1 /
4
×
3 in.) without projections.
Mass
Approx. 115 g (4.1 oz) the player only
US and foreign patents licensed from Dolby
Laboratories.
Design and specifications are subject to change without notice.
Optional accessories
MDR series stereo Headphones/earphones*
SRS series Active Speakers
∗
When using optional headphones, use only headphones/earphones with stereo mini plugs. You cannot use headphones/ earphones with micro plugs.
Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information about the accessories in your country.
Troubleshooting and explanations
Troubles and solutions
If you find any troubles operating the player, follow the steps below.
1
Check this section, “Troubles and solutions”.
2
If you cannot solve the problem after you made checks, consult your nearest Sony dealer.
While playing
Symptom
An MD is not played normally.
An MD is not played from the first track.
Cause/Remedy
• Repeat play is selected.
, Use MENU on the player to change back to the normal play
• Playback mode is changed.
, Use MENU on the player to change back to the normal play
• Disc playing stopped before it came to the last track.
, Press NX for 2 seconds or more to start playing.
• Group play mode is selected.
, Use MENU on the player to change back to the normal play
(page 30), and then press NX for 2 seconds or more to start
playing.
• The digital sound preset is off.
, Select “SOUND1” or “SOUND2” (page 23).
The digital sound preset function does not work.
Playback sound skips.
Sound has a lot of static.
Noise is momentarily heard.
Volume cannot be turned up.
• The player is placed where it receives continuous vibration.
, Put the player on a stable place.
• A very short track may cause sound to skip.
, Try not to create a track under one second long.
• Strong magnetism from a television or such device is interfering with operation.
, Move the player away from the source of strong magnetism.
• The sound was recorded in LP4 stereo mode.
, Because of the nature of the compression method used in LP4 mode, noise may be output on very rare occasions during playback of sound recorded in this mode.
• AVLS is on.
, Release AVLS settings (page 32).
39
40
Symptom
No sound comes through the headphones/ earphones.
The player skips to several tracks ahead or behind when you press
. or >.
The edited tracks may exhibit sound dropout during search operations.
Cause/Remedy
• The headphones/earphones plug is not firmly connected.
, Plug in the plug of the headphones/earphones firmly to i.
• Volume is too low.
, Adjust the volume by pressing VOL + or –.
• The plug is dirty.
, Clean the plug.
• The GROUP button has been pressed ( display).
is flashing in the
, The player returns to normal if no operation has made for 5 seconds.
• This occurs due to the MiniDisc system limitation. The fragmentation of data may cause sound dropout while searching because the tracks are played in higher speed than normal playback.
While using group function
Symptom
The group function does not operate.
A track cannot be transferred to a new group. A new group cannot be created on the supplied
SonicStage software.
Cause/Remedy
• While using a disc with no group setting, an attempt was made to select some group-related menu (“No Gp” appears in the display).
, Use a disc with group setting.
• This is due to the MiniDisc system limitations. Group information has been written to the area where the disc name is stored. The disc name and track names are recorded in the same area, which can store a maximum of approximately 1,700 characters. If the total number exceeds this amount, a new group cannot be created even though group mode is on. It is also impossible to make group settings at this time.
While using the radio
Symptom
The radio does not operate.
Cause/Remedy
• The supplied remote control is connected to other unit than this player. The supplied remote control should be used with this player only.
• After confirming that “NO DISC” has disappeared from the display on the remote control, press RADIO ON/OFF again on the remote control.
Symptom e flashes in the display on the remote control and the radio does not operate.
Cause/Remedy
• The alkaline dry battery is used up.
— Replace the battery with new LR6 (size AA) alkaline dry
Others
Symptom
The player does not work or works poorly.
The player will not play.
Cause/Remedy
• The volume is low.
, Turn up the volume.
• No disc is inserted (“NoDISC” appears in the display).
, Insert a recorded disc.
• The HOLD function is turned on (“HOLD” appears in the display when you press an operation button on the player).
, Disable HOLD by sliding the HOLD switch to the opposite direction of the arrow.
• The lid is not firmly closed.
, Close the lid until it clicks.
• Moisture has condensed inside the player.
, Take the MD out and leave the player in a warm place for several hours until the moisture evaporates.
• The dry battery is weak (“LoBATT” flashes or nothing appears).
, Replace the dry battery with a new one.
• The dry battery have been inserted incorrectly.
, Insert the battery correctly.
• An MD with nothing recorded on is inserted (“BLANK” appears in the display).
, Insert a recorded MD.
• The disc is damaged or does not contain proper recording (“Rd
ERR” appears in the display).
, Reinsert the disc. If the error message still appears, replace it with another disc.
, While operating, the player received a mechanical shock, too much static, abnormal power voltage caused by lightning, etc.
, Restart the operation as follows.
1 Remove the dry battery from the player.
2 Leave the player for about 30 seconds.
3 Insert the dry battery.
• A Hi-MD disc or a standard disc in Hi-MD mode is inserted.
, Hi-MD discs or standard discs in Hi-MD mode cannot be played on this player.
41
42
Explanations
About the DSP TYPE-S for ATRAC/ATRAC3
This player supports playback with the DSP TYPE-S specification for high-level Sony MiniDisc decks equipped with digital signal processors (DSP). This specification allows tracks recorded in
MDLP mode to be played back with high quality sound. Since this player also supports DSP
TYPE-R specification, superb sound is produced during playback in SP (normal stereo) mode as well.
Suppressing the skips of the sound (G-PROTECTION)
The G-PROTECTION function was developed to provide a higher level of shock resistance than that of existing players.
43
What you can do with MD Simple
Burner/SonicStage
What you can do with MD Simple Burner
MD Simple Burner allows you to record music tracks from an audio CD in the CD drive of your computer to an MD Walkman, without first recording the music tracks to the computer.
MD Walkman
Audio CD
44
What you can do with SonicStage
SonicStage allows you to import audio data to your computer from music sources such as audio CDs and the Internet, and then transfer the audio data stored in your computer to an
MD.
Audio CD
MD Walkman
Import
Transfer
Internet Music files in the
MP3,WAV formats
Basic operational flow using an MD Walkman
MD Simple Burner SonicStage
Providing the required system environment (page 46)
Installing the software onto your computer (page 47)
Connecting an MD walkman to your
computer (page 48)
Recording music tracks from an audio CD in the
CD drive of your
computer (page 49)
Importing audio data to
your computer (page 51)
Connecting an MD walkman to your
computer (page 48)
Transferring audio data from your computer
(page 53)
Listening to an MD
45
Installing
Providing the required system environment
System requirements
The following system environment is required in order to use the SonicStage Ver. 2.0/MD
Simple Burner Ver. 2.0 software for the MD Walkman.
Computer
Operating
System
Display
Others
IBM PC/AT or Compatible
• CPU: Pentium II 400 MHz or higher (Pentium III 450 MHz or higher is recommended.)
• Hard disk drive space: 200 MB or more (1.5 GB or more is recommended) (The amount space will vary according to Windows version and the number of music files stored on the hard disk.)
• RAM: 64 MB or more (128 MB or more is recommended)
Others
• CD drive (capable of digital playback by WDM)
• Sound Board
• USB port (supports USB (previously USB 1.1))
Factory installed:
Windows XP Media Center Edition 2004/Windows XP Media Center
Edition/Windows XP Professional/Windows XP Home Edition/
Windows 2000 Professional/Windows Millennium Edition/Windows
98 Second Edition
High Color (16bit) or higher, 800
×
600 dots or better (1024
×
768 dots or better is recommended)
• Internet access: for Web registration, EMD services and CDDB
• Windows Media Player (version 7.0 or higher) installed for playing
WMA files
46
This software is not supported by the following environments:
• OSs other than the indicated above
• Personally constructed PCs or operating systems
• An environment that is an upgrade of the original manufacturer-installed operating system
• Multi-boot environment
• Multi-monitor environment
• Macintosh
Notes
• We do not ensure trouble-free operation on all computers that satisfy the system requirements.
• The NTFS format of Windows XP/Windows 2000 Professional can be used only with the standard
(factory) settings.
• We do not ensure trouble-free operation of the system suspend, sleep, or hibernation function on all computers.
• For Windows 2000 Professional users, install Service Pack 3 or later version before using the software.
Installing the software onto your computer
Before installing the software
• Make sure to close any virus-check software, as such software usually demands a large amount of system resources.
• Even if OpenMG Jukebox, SonicStage, SonicStage Premium, SonicStage Simple Burner, or Net MD Simple Burner has been previously installed, install the software with the supplied CD-ROM. The existing software may be overwritten by the new version or it may co-exist with SonicStage depending on the version of your software. Follow the instructions that appear in the window for the installation.
You will still be able to use music data registered by a previous software version even if the previous version has been overwritten by or co-exists with new SonicStage Ver. 2.0.
As a precaution, we recommend that you back up your music data. To back up the data, refer to [Backing Up My Library] – [Backing Up Data to a Disk] on SonicStage Help .
1
Turn on your computer and start up Windows.
2
Insert the supplied CD-ROM into the CD drive of your computer.
The setup program starts up automatically and the installation window appears.
Depending on the region, a window may appear asking you to select your country. In this case, follow the displayed instructions.
3
Click [Install SonicStage and MD Simple Burner] and then follow the displayed instructions.
Click [Install SonicStage and MD Simple
Burner]
Read the instructions carefully.
Depending on your region, the buttons other than [Install SonicStage and MD Simple
Burner] may differ from those in the illustration above.
The installation may take 20 to 30 minutes, depending on your system environment.
Make sure to restart your computer only after the installation is completed.
Was the installation successful?
If any trouble occurs during the installation, see “Troubleshooting” (page 63).
47
48
Connecting the MD Walkman to your computer
After the software installation is completed, connect the MD Walkman to your computer.
1
Insert a recordable disc into the MD Walkman.
2
Insert the new dry battery into the MD Walkman, and connect the MD
Walkman to the computer using the supplied dedicated USB cable.
To the USB connecting terminal
MD Walkman
Insert the new dry battery
Dedicated USB cable
To the USB jack/ dedicated jack
Computer
3
Check the connections.
When the connections have been properly made, “PC ppMD”* appears in the display of the MD Walkman.
∗
Depending on the MD Walkman, “Net MD” may be displayed.
Note
When using the MD Walkman connected to your computer, it is recommended that you use a new dry cell battery. We do not assure the results should there be a mis-operation, transferring failure, or destruction of audio data caused by insufficient battery power.
Using MD Simple Burner
Recording by computer operations
MD Simple Burner allows you to record music tracks from an audio CD in the CD drive of your personal computer to the MD Walkman.
To start MD Simple Burner, click [Start] – [All Programs]* – [MD Simple Burner] – [MD
Simple Burner].
∗
[Programs] in the case of Windows 2000 Professional/Windows Millennium Edition/Windows 98
Second Edition z
There are other ways to start up MD Simple Burner as follows:
• Double-click the MD Simple Burner icon in the task tray, or right-click and select [Show
Standard Mode].
• Double-click the MD Simple Burner shortcut icon on the desktop.
Notes
• Only audio CDs with a mark can be used with MD Simple Burner.
• We do not guarantee normal operation in the case of the copy-controlled CDs.
The window for recording all tracks on the CD
[REC/STOP]
To start recording all tracks on the CD as a new group, click here.
To stop recording, click [Stop].
CD icon
Total time of the selected tracks of CD MD icon Disc name (MD)
Artist name (CD)
Album name (CD)
[OPEN]
To open the display as shown on page
Recording mode drop down list
LP2/LP4
Remaining recording time of the inserted MD
49
The window for recording selected tracks from an audio CD
Track information
(CD)
Artist name
Total time of the selected tracks of CD
[CONFIG]
Click here to do the following:
-Set the CD-ROM drive
-View version information for MD Simple Burner
-Confirm CD information registered in the CDDB
Album Title
[REC/
STOP]
Disc name
(MD)
Track information (MD)
You can change the track name and track number
50
[Get CD info]
Information of an audio CD
(album name, track title, etc.) will be reflected in the track list.
[New Group]
Recording mode drop down list
[CLOSE]
To close the display as shown
CD operating section
Use these controls to confirm the tracks on audio CD to be recorded
To deselect all tracks, click here.
To select all tracks, click here.
[Erase]
[All Erase]
Check boxes
Check the box of the tracks that you want to record
Remaining time of the inserted MD
Using SonicStage
Importing audio data
This section explains how to record and store audio data from an audio CD to My Library of SonicStage on the hard disk drive of your computer.
You can record or import music from other sources such as the Internet and your computer’s hard disk. Refer to SonicStage Help for details.
Notes
• Only audio CDs with a mark can be used with SonicStage.
• We do not guarantee normal operation in the case of the copy-controlled CDs.
Source indication
[Music Source]
[CD Info]
[Format/Bit Rate]
1
Start up SonicStage
.
Select [Start] – [All Programs] * – [SonicStage] – [SonicStage].
∗
[Programs] in the case of Windows 2000 Professional/Windows Millennium Edition/Windows 98
Second Edition
SonicStage starts up and the main window appears.
z
You can also start SonicStage with double click ([SonicStage] icon) on the desktop.
2
Insert the audio CD that you want to record into the CD drive of your computer.
The source indication in the top-left of the display changes to [Record a CD].
3
Click [Music Source].
The contents of the audio CD appear in the music source list (on the left side of the screen).
continued
51
52
4
If necessary, click to uncheck tracks you do not want to record.
If you unchecked a box by mistake, click it again to restore the check.
To check all boxes, click
To uncheck all boxes, click
.
.
5
If necessary, change the format and bit rate for recording the audio CD.
When you click [Format/Bit Rate] on the right side of the screen, “CD Recording
Format [My library]” dialog box will appear. The dialog box will ask you to select the format and bit rate for recording the audio CD.
6
Click .
The recording of the tracks selected in step 4 starts.
To stop recording
Click .
z
If CD information such as album title, artist name, and track names could not be obtained automatically, click [CD Info] on the right side of the screen. When you do this, your computer must be connected to the Internet.
Transferring audio data from your computer to the
MD Walkman
Audio data stored in My Library of SonicStage can be transferred to your MD Walkman an infinite number of times.
Transfer Destination list
[Transfer]
The My Library list
[Transfer Mode]
1
Connect your MD Walkman to the computer.
After making the connections, “Net MD” is displayed in the Transfer Destination list in the upper right of the screen.
For details about connections, see “Connecting the MD Walkman to your computer”
Do not disconnect the power source or the dedicated USB cable before the transfer has completed.
2
Click [Transfer].
The screen is switched to the Transfer (Net MD) screen.
3
Click the tracks you want to transfer in the My Library list on the left side of the screen.
To transfer more than one track, hold down the [Ctrl] key while selecting the tracks.
To transfer all tracks of the album, click the album.
4
Change the transfer mode, if necessary.
Click [Transfer Mode] in the middle of the screen to display the “Transfer Mode
Settings” dialog box (for Net MD) and select the transfer mode.
continued
53
54
5
Click .
Transfer of the tracks selected in step 3 begins.
To stop transferring
Click .
Notes
• A transfer will fail and an error message will appear in the following cases:
—When there is no enough free space on the disc.
—When the track is subject to playback restrictions.
• During the transfer, the system suspend, sleep, or hibernation function will not operate.
• Depending on the type of the text and number of characters, the text entered by SonicStage may not be displayed on the connected MD Walkman. This is due to the limitations of the connected MD
Walkman.
• When using your MD Walkman connected to the computer, be sure to use a new battery. We do not assure the results should there be a mis-operation, transferring failure, or destruction of audio data caused by insufficient battery power.
Transferring back audio data from the MD Walkman to your computer
Transfer
Destination list
[Transfer]
The My Library list
List of tracks on the MD
Transferring from the MD Walkman back to your computer
Audio data that has been transferred from your computer and stored on the MD can be transferred back to My Library of SonicStage on your computer.
1
Connect your MD Walkman to the computer.
After making the connections, “Net MD” is displayed in the Transfer Destination list in the upper right of the screen.
For details about connections, see “Connecting the MD Walkman to your computer”
Do not disconnect the power source or the dedicated USB cable before the transfer has completed.
2
Click [Transfer].
The screen is switched to the Transfer (Net MD) screen.
3
In the Net MD list on the right side of the screen, click to select the tracks you want to transfer to your computer.
continued
55
56
4
Click in the middle of the screen.
The transferring of the tracks selected in step 3 starts.
To stop transferring
Click .
Note
Tracks transferred to the MD Walkman from another computer cannot be transferred back to My
Library on your computer.
Using SonicStage Help
SonicStage Help provides further details on how to use SonicStage. SonicStage Help allows you to search easily for information from a list of operations, such as “Importing audio data” or “Transferring audio data”, or from large list of keywords, or by typing in words that might lead you to the appropriate explanations.
To display SonicStage Help
Click [Help] – [SonicStage Help] while SonicStage is running.
[SonicStage Help] z
You can display SonicStage Help by selecting the following:
[Start] – [All Programs]*– [SonicStage] – [SonicStage Help] .
∗
[Programs] in the case of Windows 2000 Professional/Windows Millennium Edition/Windows 98
Second Edition
Notes
• In SonicStage Help, “Device/Media” is the general term for the external device such as the MD
Walkman, the Network Walkman, and the CD Walkman.
• Follow the instructions of your internet provider regarding such things as recommended system.
57
Understanding SonicStage Help
The right side frame
The left side frame
58
1 Double click [Overview] in the left-side frame.
2 Click [About This Help File].
The explanation will appear in the right-side frame.
3 Read the text.
Scroll the display if necessary.
Click underlined words to jump to their explanations.
Searching for a word inside an explanation
[Search]
“Type in the keyword to find” text box
List Topics
The list of the words that you searched
[Display]
1 Click [Search] to open the “Search” window.
2 Type in the words.
3 Click [List Topics].
A list of the words that were searched is displayed.
4 Click to select the desired item among those displayed.
5 Click [Display].
An explanation of the selected item is displayed .
An explanations of the selected item
Referring to SonicStage Help
Click [Contents] on the left side of the Help window to view a list of items for each operation. Click on any items for details.
Importing audio data to the computer
To
Import audio data from the
Internet
Import audio files on the computer in SonicStage
SonicStage Help
[Importing tracks] – [Purchasing Tracks from a Music
Service Site]
[Importing tracks] – [Importing Music Files]
Listening to audio data on the computer
To
Listen to audio data from the
CD drive or My Library
Listen to audio data on the MD
Walkman connected to the computer
SonicStage Help
[Music Playback] – [Playing Back an Audio CD] or
[Playing Back a Track in My Library]
[Music Playback] – [Playing Back a Track on a Device/
Media]
Managing and editing imported tracks
To
Change information related to
CD information downloading
Edit an album
Delete the tracks
Change the destination directly for track storage
SonicStage Help
[Changing SonicStage Settings] – [Changing Settings for Getting CD information]
[Managing Tracks and Albums]
Albums]
– [Creating/Editing
[Changing SonicStage Settings] – [Changing the
Location for Saving Recorded Files]
59
60
Backing up audio data
We recommend that you back up your music data as a precaution against hard disk crashes or computer replacement.
To
Back up audio data in My
Library
Look up about SonicStage backup
SonicStage Help
[Backing Up My Library] – [Backing Up Data to a
Disk]
[Backing Up My Library]
Backup Tool]
– [FAQ-About SonicStage
Troubleshooting
To
Look up troubleshooting procedure
SonicStage Help
[Additional Information] – [Troubleshooting]
When you want to know
To
Look up unknown words
Look up the kinds of audio data that can be managed by
SonicStage
Look up the kinds of functions that can be used with
SonicStage
SonicStage Help
[Additional Information]
[Overview] –
– [Glossary]
[Content Handled Within SonicStage]
[Overview] – [Features]
Other information
Uninstalling SonicStage/MD Simple Burner
To uninstall SonicStage/MD Simple Burner, follow the procedures below.
1
Click [Start]–[Control Panel]*.
∗
[Settings]–[Control Panel] in the case of Windows 2000 Professional/Windows Millennium
Edition/Windows 98 Second Edition
2
Double-click [Add/Remove Programs].
3
Click [SonicStage 2.0.xx] or [MD Simple Burner 2.0.xx] in the “Currently
Installed Programs” list, and then click [Change and Remove]
*
.
Follow the displayed instruction and restart your computer. The uninstallation is completed when the computer has restarted.
∗
[Change/Remove] in the case of Windows 2000 Professional, [Add/Remove] in the case of
Windows Millennium Edition/Windows 98 Second Edition
Note
When you install SonicStage Ver. 2.0/MD Simple Burner Ver. 2.0, OpenMG Secure Module 3.4 is installed at the same time. Do not delete OpenMG Secure Module 3.4 since it may be used by other software.
61
62
On copyright protection
The OpenMG technology allows you to enjoy digital music, while maintaining the copyrights of its holders. SonicStage encrypts audio files in OpenMG format and stores them on the hard disk of your computer to prevent unauthorized distribution.
Restrictions on audio content
High-quality digital audio content is widely available through music distribution services on the Internet. To protect the copyrights of its holders from unauthorized distribution, some audio content is distributed with certain restrictions on recording and playback. For example, the playback period or playback count for the data may be limited.
Troubleshooting
Please refer to the following steps if you encounter a problem while using SonicStage/MD
Simple Burner.
1
Check the symptoms in this “Troubleshooting” section.
2 Check the symptoms in SonicStage Help when you use SonicStage.
3 If the problem cannot be solved after checking the above references.
Check the following table and then consult your nearest Sony dealer.
Computer
• Manufacturer:
• Model:
• Type: Desktop type / Laptop type
Name of operating system:
RAM capacity:
Hard disk drive (containing SonicStage/MD Simple Burner and audio data)
• Capacity of the drive:
• Free space:
Version of the software
• SonicStage Ver. 2.0
1)
• MD Simple Burner Ver. 2.0
2)
Error Message (if one appear):
If an externally connected CD-ROM drive is used
• Manufacturer:
• Model:
• Type: CD-ROM / CD-R/RW / DVD-ROM / Other ( )
• Type of connection to the computer: PC card / USB / IEEE1394 / Other ( )
If another device with USB connection is used
• Name of the device (or devices):
1)
2)
To check the SonicStage software version, go to [Help] – [About SonicStage] in the SonicStage window.
To check the MD Simple Burner software version, go to [CONFIG] – [Version] in the MD Simple
Burner window.
63
64
The software cannot be installed onto your computer
Problem
The installation was not successful.
The installation appears to have stopped before it has completed.
The progress bar on the display is not moving. The access lamp has not lit for a few minutes.
Cause/Remedy
You are using an OS that does not support this software.
tSee page 46 for more details.
All windows applications are not closed.
tIf you start the installation while other programs are running, a malfunction may occur. This is especially true for programs that require large amounts of system resources, such as virus-check software.
There is not enough hard disk space on your hard disk.
tYou need 200MB or more free space on your hard disk.
Check for the appearance of an error message beneath the installation window.
t Press the [Tab] key while holding down the [Alt] key. If an error message has appeared, press the
[Enter] key. The installation will resume. If there is no message, the installation is still in progress. Wait a little while longer.
The installation is progressing normally. Please wait.
The installation may take 30 minutes or more, depending on your CD drive or system environment.
Using a MD Walkman connected to the computer
Problem
Your computer does not recognize the MD Walkman.
Even though the dedicated
USB cable is used to connect the MD Walkman to the computer, the display on the
MD Walkman does not indicate it is connected.
Cause/Remedy
The MD Walkman is not firmly connected with the supplied dedicated USB cable to the computer.
tReconnect the MD Walkman to the computer firmly.
A disc is not inserted in the MD Walkman.
tCheck if a disc is inserted in the MD Walkman.
The Net MD driver is not be installed.
tInstall the SonicStage/MD Simple Burner software using the supplied CD-ROM.
It takes time to recognize SonicStage. Please wait.
The other application software is running.
tReconnect the supplied dedicated USB cable after a while. If the computer still does not recognize the
MD Walkman, disconnect the MD Walkman, restart the computer, and connect the dedicated USB cable again.
The progress bar on the display is not moving. The access lamp has not lit for a few minutes.
The supplied dedicated USB cable is disconnected.
tConnect the supplied dedicated USB cable firmly.
The connections are made through a USB hub.
tOperations are not guaranteed for USB-hub connections. Connect the MD Walkman directly to the USB connector on the computer.
65
66
Index
A
Accessories optional
AVLS
B
Battery life
C
CD drive
CDDB
CD-ROM
Checking
Cleaning
Connecting
Copyright protection
D
Digital Sound Preset
DSP TYPE-S
E
EMD service
G
G-PROTECTION
Group
skip
H
Hard disk
HOLD
I
Importing
Installing
M
MD Simple Burner
My Library
O
OpenMG Secure Module 3.4
P
Play mode group
tracks
Presetting radio stations
Q
Quick Mode
R
Recording mode (Bit rate)
S
SonicStage
SonicStage Help
Start (software)
SonicStage
System environment
System limitations
T
Transferring
to your computer
U
Uninstalling
USB
USB port
W
Windows 2000 Professional
,
Windows 98 Second Edition
,
,
Windows Media Player
Windows Millennium Edition
,
,
Windows XP Home Edition
Windows XP Media Center Edition
Windows XP Media Center Edition 2004
Windows XP Professional
WMA
This warranty is valid only in Canada.
This warranty is valid only in the United States.
Printed in Malaysia
* 3 2 6 6 4 3 7 1 1 * (1)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project