Sony XR-4803 Service manual

SERVICE MANUAL

XR-4803

East European Model

Model Name Using Similar Mechanism

Tape Transport Mechanism Type

SPECIFICATIONS

NEW

MG-25F-136

MICROFILM

– Continued on next page –

FM/MW/LW CASSETTE CAR STEREO

– 2 –

TABLE OF CONTENTS

1.

GENERAL

................................................................... 3

2.

DISASSEMBLY

......................................................... 9

3.

ASSEMBLY OF MECHANISM DECK

........... 11

4.

MECHANICAL ADJUSTMENTS

....................... 14

5.

ELECTRICAL ADJUSTMENTS

Test Mode ........................................................................ 14

Tape Deck Section .......................................................... 14

Tuner Section .................................................................. 15

6.

DIAGRAMS

6-1. IC Pin Function Description ........................................... 17

6-2. Printed Wiring Board – MAIN Section – ...................... 21

6-3. Schematic Diagram – MAIN Section – .......................... 23

6-4. Printed Wiring Board – PANEL Section – .................... 27

6-5. Schematic Diagram – PANEL Section – ....................... 29

7.

EXPLODED VIEWS

................................................ 33

8.

ELECTRICAL PARTS LIST

............................... 36

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be damaged by heat.

SECTION 1

GENERAL

This section is extracted from instruction manual.

– 3 –

– 4 –

– 5 –

– 6 –

– 7 –

– 8 –

SECTION 2

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

FRONT PANEL ASS’Y

1

Push the button

(release).

2 Remove the front panel ass’y to the direction of the arrow

A

.

A

COVER ASS’Y

1

2

2

1

3 cover ass’y

2

1

– 9 –

SUB PANEL, MECHANISM DECK (MG-25F-136)

3 connector

(CN351)

5 screw

(PTT2.6

×

6)

6 mechanism deck

(MG-25F-136)

4 flexible flat cable

(CN301)

2 sub panel

1 three screws

(PTT2.6

×

8)

1 three screws

(PTT2.6

×

8)

MAIN BOARD, HEAT SINK

3 two ground point screws

4

main board

5 two screws

(PTT2.6

×

5)

5 three screws

(PTT2.6

×

10)

1 screw

(PTT2.6

×

8)

5 screw

(PTT2.6

×

8)

6

heat sink

2

rubber cap (25)

1 two screws

(PTT2.6

×

8)

– 10 –

SECTION 3

ASSEMBLY OF MECHANISM DECK

Note: Follow the assembly procedure in the numerical order given.

HOUSING

5 Fit projection on C part.

2

Install the hanger onto two claws of the housing.

4

Fit claw on

B

part.

7

Holder the hanger by bending the claw.

1 Install the catch to the hanger. hanger

3 Put the housing under

A

part.

6 Fit projection on D part.

housing

C part

8 Hold the hanger by bending the claw.

D

part

ARM (SUCTION)

A

part

B part

2 Move the arm (suction) in the arrow direction and fit on projection.

projection

1

Fit the arm (suction) on the shaft.

– 11 –

LEVER (LDG-A) / (LDG-B)

shaft A shaft B shaft C shaft

A shaft B

1 Fit the lever (LDG-A) on shafts

A

–

C

and install it.

3

type-E stop ring 2.0

2

Fit the lever (LDG-B) on shafts A and B and install it.

GEAR (LDG-FT)

hole gear (LDG-D) hole lever (LDG-A) gear (LDG-FB)

4 Align hole in the gear (LDG-D) with hole the lever (LDG-A).

5

gear (LDG-FT)

6

polyethylene washer

2 tension spring (LD-2)

1

2 tension spring (LD-1)

3 Move the lever (LDG-B) in the arrow direction.

– 12 –

GUIDE (C)

2

guide (C)

1

three claws

– 13 –

SECTION 4

MECHANICAL ADJUSTMENTS

1. Clean the following parts with a denatured-alcohol-moistened swab: playback head pinch roller rubber belt idler capstan

2. Demagnetize the playback head with a head demagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.

4. After the adjustments, apply suitable locking compound to the parts adjusted.

5. The adjustments should be performed with the power supply voltage unless otherwise noted.

• Torque Measurement

Mode

Forward

Torque Meter

CQ-102C

Forward

Back Tension

Reverse

Reverse

Back Tension

FF, REW

CQ-102C

CQ-102RC

CQ-102RC

CQ-201B

Meter Reading

30 – 65 g•cm

(0.42 – 0.90 oz•inch)

0.5 – 4.5 g•cm

(0.01 – 0.06 oz•inch)

30 – 65 g•cm

(0.42 – 0.90 oz•inch)

0.5 – 4.5 g•cm

(0.01 – 0.06 oz•inch)

60 – 200 g•cm

(0.83 – 2.78 oz•inch)

• Tape Tension Measurement

Mode Tension Meter

Forward CQ-403A

Reverse CQ-403R

Meter Reading more than 90 g

(more than 3.18 oz) more than 90 g

(more than 3.18 oz)

SECTION 5

ELECTRICAL ADJUSTMENTS

TEST MODE

This set have the test mode function. In the test mode, FM Auto

Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments can be performed easier than it in ordinary procedure.

<Set the Test Mode>

1. Set the “power select” switch (S501) is “A” position.

2. Turn ON the regulated power supply. (All LEDs on the set lights up, and the clock is displayed.)

Note: Press the

[OFF]

button, if the clock is not displayed.

3. Push the preset

4. Push the preset

5. Press the preset

[4]

button.

[5]

button.

[1]

button for more than two seconds.

6. Then the display indicates all lights, the test mode is set.

<Release the Test mode>

1. Push the

[OFF]

button.

2. Return the “power select” switch (S501) to initially set position.

See the adjustment location from on page 16 for the adjustment.

TAPE DECK SECTION

Tape Speed Adjustment

Setting:

0 dB=0.775 V test tape

WS-48A

(3 kHz, 0 dB) speed checker or frequency counter

4

Ω set

– + speaker out terminal

Procedure:

1. Put the set into the FWD PB mode.

2. Adjust adjustment resistor for inside capstan motor so that the reading on the speed checker or frequency counter becomes in specification.

Specification: Constant speed

Speed checker

–1.5 to +2.5%

Adjustment Location: See page 16.

Frequency counter

2,955 to 3,075 Hz

– 14 –

TUNER SECTION

0 dB=1 µV

Cautions during repair

When the tuner unit is defective, replace it by a new one because its internal block is difficult to repair.

Note: Adjust the tuner section in the sequence shown below.

1. FM Auto Scan/Stop Level Adjustment.

2. FM Stereo Separation Adjustment.

3. AM (MW) Auto Scan/Stop Level Adjustment.

FM Auto Scan/Stop Level Adjustment

Setting:

[SOURCE]

button: FM

FM RF signal generator antenna jack (J1)

0.01

µ

F set

Carrier frequency : 98.0 MHz

Output level : 22 dB (12.6

µ

V)

Mode : mono

Modulation : 1 kHz, 22.5 kHz deviation (30%)

Procedure:

1. Set to the test mode. (See page 14.)

2. Push the

[SOURCE]

button and set to FM.

Display

SHUF1

FM 98.0

3. Adjust with the volume RV2 on TU1 so that the “FM” indication turns to “FMI” indication on the display window.

But, in case of already indicated “FMI”, turn the RV2 so that put out light “I” indication and adjustment.

Display

SHUF1

FM 98.0


FM Stereo Separation Adjustment

Setting:

[SOURCE]

button: FM

FM RF signal generator antenna jack (J1)

0.01

µ

F set

4

Ω level meter

+

–

Carrier frequency : 98.0 MHz

Output level : 70 dB (3.2 mV)

Mode

Modulation

: stereo speaker out terminal

: main: 1 kHz, 20 kHz deviation (26.7%) sub: 1 kHz, 20 kHz deviation (26.7%)

19 kHz pilot: 7.5 kHz deviation (10%)

Procedure:

FM Stereo signal generator output channel

L-CH

Level meter connection

L-CH

Level meter reading (dB)

R-CH

R-CH

L-CH

L-CH

R-CH

R-CH

A

B

Adjust RV4 on TU1 for minimum reading.

C

D

Adjust RV4 on TU1 for minimum reading.

L-CH Stereo separation: A-B

R-CH Stereo separation: C-D

The separations of both channels should be equal.

Specification: Separation more than 28 dB


– 15 –

AM (MW) Auto Scan/Stop Level Adjustment

Make this adjustment after “FM Auto Scan/Stop Level Adjustment”.

Setting:

[SOURCE]

and

[MODE]

button: MW

30

Ω

15 pF

65 pF

AM RF signal generator

AM dummy antenna

(50

Ω

) set antenna jack (J1)

Carrier frequency : 999 kHz

30% amplitude modulation by

1 kHz signal

Output level : 33 dB (44.7

µ

V)

Procedure:

1. Set to the test mode. (See page 14.)

2. Push the

[SOURCE]

button and set to FM.

3. Push the

[MODE]

button and set to MW.

Display

INTRO

SHUF1

MW 999

4. Adjust with the volume RV1 on TU1 so that the “MW” indication turns to “MWI” indication on the display window.

But, in case of already indicated “MWI”, turn the RV1 so that put out light “I” indication and adjustment.

Display

INTRO

SHUF1

999

Adjustment Location:

—SET UPPER VIEW–

Tape Speed Adjustment

TU1

RV4 FM Stereo Separation Adjustment

RV2 FM Auto Scan/Stop Level Adjustment

RV1 AM (MW) Auto Scan/Stop Level Adjustment

– 16 –

SECTION 6

DIAGRAMS

34

35

36

31

32

33

26

27

28

29

30

37

38

39

40

9

17

18

19

20

14

15

16

21

22

23

10

11

12

13

6-1.

IC PIN FUNCTION DESCRIPTION

•

MAIN BOARD IC501

µ

PD17707GC-529-3B9 (SYSTEM CONTROLLER)

Pin No.

1

2

3

4

5

6

7

8

Pin Name

AMSSEL

POS3

POS2

POS0

POS1

TAPEON

CM ON

LM LOD

I/O

I

I

I

I

Function

Setting terminal for the AMS selection fixed at “L”

Tape position detect input from tape operation switch on the mechanism block

I

O Tape system power supply on/off control signal output terminal “H”: tape on

O Capstan/reel motor (M901) drive signal output terminal “H”: motor on

O

Loading/tape operation motor control signal output to the MM1322XFBE (IC351)

(For the loading direction and forward side operation) *1

24

25

LM EJ

TUNON

FM ON

PW ON

MUT

VOLCE

VOLCKO

VOLSO

AMPON

AMPMUT

DX/LO

NCO

GND

DSTSEL

D-BASS

KEYIN1

KEYIN0

O

I

Loading/tape operation motor control signal output to the MM1322XFBE (IC351)

(For the eject direction and reverse side operation) *1

O Tuner system power supply on/off control signal output to the BA3918 (IC611) “H”: tuner on

O FM system power supply on/off control signal output to the BA3918 (IC611) “H”: FM on

O Main system power supply on/off control signal output to the BA3918 (IC611) “H”: power on

O Line muting control signal output terminal “H”: line muting on

O Chip enable signal output to the electrical volume (IC331)

O Serial data transfer clock signal output to the electrical volume (IC331)

O Serial data output to the electrical volume (IC331)

O Standby control signal output to the power amplifier (IC751) “L”: standby

O Muting control signal output to the power amplifier (IC751) “L”: muting on

O Local/DX selection signal output to the FM/AM tuner unit (TU1) “L”: DX, “H”: local

O Not used (open)

— Ground terminal

I Destination setting terminal (fixed at center voltage)

I D-BASS switch (SW951) input (A/D input)

Key input terminal (A/D input)

6, INTRO 1, REPEAT 2, 3, BL SKIP 6, ATA 5, MTL 4 keys input (LSW921 to LSW927)

I

Key input terminal (A/D input)

OFF, SOURCE, MODE *, + ) + SEEK AMS, – = 0 SEEK AMS, VOLUME –,

SEL, VOLUME +, ATT, DSPL, BTM, LCL keys input

(LSW901 to LSW909, LSW930, LSW911 and LSW912)

RC IN0

VSM

AMIFIN

FMIFIN

VDD2

FM OSC

AM OSC

GND

NCO

EO1

TEST0

NCO

SEKOUT

MW SW

BEEP

I

I

Rotary remote commander shift key A/D input terminal

FM and AM (MW/LW) signal meter voltage detection input from the FM/AM tuner unit (TU1)

I

I

AM (MW/LW) intermediate frequency detection signal input from the FM/AM tuner unit (TU1)

FM intermediate frequency detection signal input from the FM/AM tuner unit (TU1)

— Power supply terminal (+5V)

I

I

FM local oscillator detection signal input from the FM/AM tuner unit (TU1)

AM (MW/LW) local oscillator detection signal input from the FM/AM tuner unit (TU1)

— Ground terminal

O Not used (open)

O Main charge-pump control signal output terminal

I Setting terminal for the test (fixed at “L”)

O Not used (open)

O Seek control signal output to the FM/AM tuner unit (TU1)

O MW/LW selection signal output to the FM/AM tuner unit (TU1) “L”: MW, “H”: LW

O Beep sound output terminal

– 17 –

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

Pin No.

41

42

43

44

45

46

47

48

49

50

Pin Name

KEYACK

BU IN

MTLSEL

DOLON

AMSIN

ST

AMS ON

N/R OUT

TAPMUT

ILLON

SD IN

NOSESW

TELMUTE

REL

ACCIN

TESTIN

RC IN1

PW SEL

MTLIN

ADON

KEYSEL

SEKOUTSEL

COLORSEL

LCDCE

LCDCKO

LCDSO

LCDINH

UNICKI

I/O

I

I

I/O

Function

Input of acknowledge signal for the key entry Acknowledge signal is input to accept function and eject keys in the power off status On at input of “L”

Battery detect signal input terminal “H”: battery on

METAL control in/out terminal

At initial mode: auto/manual mode selection input of METAL function “L”: manual mode

At manual mode: METAL on/off control signal output to the CXA2509AQ (IC301)

“H”: METAL on

At auto mode: input at MTLIN (pin %ª)

I/O

I

I/O

Dolby control in/out terminal

At initial mode: valid/invalid selection input of dolby function (“L” input: valid)

At normal mode: dolby on/off control signal output “H”: dolby on

Not used this function in this set (fixed at “H”)

Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor

“L”: music is present, “H”: music is not present

Input of FM stereo detection signal from FM/AM tuner unit (TU1), and output of forced monaural control signal to FM/AM tuner unit (TU1) (Commonly used for stereo display input and forced monaural output)

FM stereo detection at input of “L”, forced monaural at output of “L”

O

O

Tape auto music sensor control signal output to the CXA2509AQ (IC301)

“L” is output to lower the gain for audio level at FF/REW

Forward/reverse direction control signal output to the CXA2509AQ (IC301)

“L: forward direction, “H”: reverse direction

O Tape muting on/off control signal output to the CXA2509AQ (IC301) “H”: tape muting on

O

Power supply on/off control signal output terminal at the illumination and liquid crystal display driver (IC901) “H”: power on

At power select switch (S501) on mode: “H” output at the accessory on

At power select switch (S501) off mode: “H” output at the power on

I

I

I

I

I

I

I

I

Station detector detect input from the FM/AM tuner unit (TU1)

Stop level for SEEK, BTM, etc. is determined SD is present at input of “H”

Detects the removal of the attaching and removing type front panel block “L”: attaching

Telephone muting signal input terminal At input of “L”, the signal is attenuated by –20 dB

Not used (fixed at “H”)

Reel table rotation detect signal input from the take-up and supply reel sensor

Accessory detect signal input terminal “L”: accessory on

Setting terminal for the test mode “L”: test mode (normally fixed at “H”)

Rotary remote commander shift key A/D input terminal

Power select switch (S501) input terminal

“L”: position A (halt mode), “H”: position B (operation mode)

I

Input terminal to set whether the auto metal function is present or not

“L”: auto metal function is present (fixed at “H”)

O Power supply on/off control signal output for the A/D conversion

I Setting terminal for the key (fixed at “H”)

I

I

Active selection terminal for the SEKOUT (pin #•) (fixed at “L”)

Setting terminal for the illumination color “L”: amber, “H”: green Not used (fixed at “L”)

O Chip enable output to the liquid crystal display driver (IC901)

O Serial data transfer clock signal output to the liquid crystal display driver (IC901)

O Serial data output to the liquid crystal display driver (IC901)

O

Blank indicate control signal output to the liquid crystal display driver (IC901)

“L”: no display

I Serial data reading clock signal input terminal for the unilink Not used (connected to pin &¡)

– 18 –

Pin No.

69

70

74

75

76

71

72

73

77

78

79

80

Pin Name

UNISO

UNISI

UNICKO

BUSON

SYSRST

VREG

GND

X OUT

X IN

CE

VDD1

RESET

I/O Function

O Serial data output terminal for the unilink Not used (open)

I Serial data input terminal for the unilink Not used (fixed at “L”)

O Serial data transfer clock signal output terminal for the unilink Not used (connected to pin ^•)

O Bus on/off control signal output terminal Not used (pull up)

O Reset signal output terminal “L”: reset Not used (pull up)

O CPU regulator output terminal Connected to capacitor

— Ground terminal

O Main system clock output terminal (4.5 MHz)

I

I

Main system clock input terminal (4.5 MHz)

CPU chip enable signal input (fixed at “H”)

— Power supply terminal (+5V)

I

System reset signal input from the reset signal generator (IC551) and reset switch (S551)

“L” is input for several 100 msec after power on, then it changes to “H”

*1 loading/tape operation motor control

MODE

TERMINAL

STOP

LM LOD (pin 8)

LM EJ (pin 9)

“L”

“L”

LOADING/

FORWARD

“H”

“L”

EJECT/

REVERSE

“L”

“H”

BRAKE

“H”

“H”

– 19 –

• IC Block Diagrams – MAIN Board –

IC301 CXA2509AQ-T4

PBFB2

PBRIN2

31

32

PBREF2 33

PBFIN2 34

VCT

PBGND

35

36

PBFIN1 37

PBREF1 38

PBRIN1

PBFB1

39

40

30

VCT

29 28 27 26

120 µ /70 µ

T2

– +

F2

F1

X1

+

X1

25

NR BIAS

TAPE/AUX

TAPE EQ

LPF

FWD/RVS

VCC

+

–

F3

24 23 22 21

24dB

+ –

MS

MODE

20

19

18

17

16

MSMODE

DRSW

TAPESW

INSW

NC

MS ON/

OFF

DETECT

15 NC

14 MSOUT

13 DGND

– +

T1

+ –

12 MSTC

11 G1FB

1

120

µ

/70

µ

2 3 4 5 6 7

24dB

8 9 10

IC351 MM1322XFBE

GND 1

IN2 2

VCC 3

IN1 4

8 OUT2

7 VS

6 OUT1

5 GND

IC331 LC75373ED

LSELO

L4

L3

L2

L1

34

35

36

37

38

VDD 39

R1

R2

R3

R4

RSELO

40

41

42

43

44

33

1

+

–

–

+

+

–

–

+

32

2

–

+

+

–

31 30 29 28 27 26 25 24 23

–

+

–

+

+

–

+

–

22 LFIN

21 LFOUT

20 LROUT

+

–

–

+

+

–

3 4 5

+

–

DECODER

+

–

LATCH

SHIFT

REGISTER

CONTROL

–

+

–

+

+

–

19 VREF

18

17

16

15

14

CE

DI

CL

VSS

RROUT

13

12

RFOUT

RFIN

6 7 8 9 10 11

– 31 –

IC611 BA3918-V2

REGULATOR

1 2 3 4

–

+

OVER VOLTAGE

PROTECT

5 6 7 8 9

–

+

10

+

– –

+

11 12

– 32 –

NOTE:

• -XX and -X mean standardized parts, so they may have some difference from the original one.

• Color Indication of Appearance Parts

Example:

KNOB, BALANCE (WHITE) . . . (RED)

↑ ↑

Parts Color Cabinet's Color

SECTION 7

EXPLODED VIEWS

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• The mechanical parts with no reference number in the exploded views are not supplied.

• Hardware (# mark) list and accessories and packing materials are given in the last of the electrical parts list.

(1) CHASSIS SECTION

8

14

15

MG-25F-136

#3

6

7

4

5

3

2

F781

9

10

12

#2

#2

#4

#2

#2

11

13

#1

#2

#2

Front panel ass’y

3

4

1

2

* 5

Ref. No.

Part No.

Description

3-009-294-01 PANEL, SUB

3-935-003-01 SPRING, TORSION

3-932-205-21 DOOR, CASSETTE

X-3367-636-1 LOCK ASSY

3-010-377-01 INSULATOR

* 6

7

* 8

A-3313-396-A MAIN BOARD, COMPLETE

3-915-923-01 SCREW, GROUND POINT

X-3373-270-1 COVER ASSY

1

Remark Ref. No.

Part No.

9

* 10

* 11

12

* 13

Description

1-776-207-41 CORD (WITH CONNECTOR) (POWER)

3-009-809-01 BRACKET (IC)

3-010-517-01 HEAT SINK (BUS NON) (E)

3-935-014-01 CUSHION (U)

3-009-813-01 CHASSIS

Remark

14

15

F781

3-012-859-01 CAP (25), RUBBER

3-937-650-01 PLATE (C), GROUND

1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)

– 33 –

(2) FRONT PANEL SECTION

102

#5 not supplied

(KEY board)

105

107

108 109

120

111

104

103

101

114

121

112

115

106

116

LCD901

113

117

118

#5

Ref. No.

Part No.

101

102

103

104

105

Description

3-018-799-01 BUTTON (D-BASS)

3-015-036-01 CUSHION (BACK PANEL)

3-016-924-01 BUTTON (L) (2) (+. –)

3-009-304-01 BUTTON (RELEASE)

3-932-475-01 SPRING (RELEASE)

* 106

107

108

109

111

Remark Ref. No.

Part No.

112

113

* 114

* 115

* 116

Description

3-016-928-11 BUTTON (4-6) (4. 5. 6)

3-016-930-01 BUTTON (R) (3) (BTM. LCL.

3-019-151-01 PLATE (LCD), GROUND

3-019-150-01 SHEET (REFLECTOR)

3-018-612-01 PLATE, LIGHT GUIDE r)

3-019-149-01 PLATE, LCD

X-3374-689-1 PANEL SUB ASSY

3-009-300-01 BUTTON (SOURCE)

3-018-797-11 BUTTON (L) (3)

(+ + ). SEEK AMS. = 0 –. r. OFF. SEL. ATT)

3-016-927-01 BUTTON (1-3) ( 6. 1. 2. 3)

* 117

118

* 120

* 121

3-018-611-01 HOLDER (LCD)

3-010-519-01 PANEL, FRONT BACK

3-024-391-01 SHEET (LCD)

3-024-846-01 SHEET (LCD) B

LCD901 1-801-966-11 DISPLAY PANEL, LIQUID CRYSTAL

Remark

– 34 –

(3) MECHANISM DECK SECTION

(MG-25F-136)

159

153

154

155

#6

158

157

156

A

152

160

A

161

162

164

168

168

#7

165

166

167

163

HP901

M901

151

Ref. No.

Part No.

151

* 152

* 153

154

155

Description

A-3291-667-A CLUTCH (FR) ASSY

3-019-130-01 LEVER (LDG-A)

3-019-131-01 LEVER (LDG-B)

3-020-539-01 SPRING (LD-1), TENSION

3-020-540-01 SPRING (LD-2), TENSION

156

157

158

* 159

160

3-020-542-01 GEAR (LOADING FT)

3-341-753-11 WASHER, POLYETHYLENE

3-020-533-01 HOUSING

3-020-532-01 ARM (SUCTION)

3-020-534-01 HANGER

Remark Ref. No.

Part No.

161

162

163

164

165

Description

3-933-346-01 CATCHER

3-933-344-01 GUIDE (C)

3-014-798-01 SCREW (HEAD), SPECIAL

3-364-151-01 WASHER

A-3301-267-A CHASSIS ASSY (F)

166

167

3-017-302-01 BELT (25)

3-936-853-01 FLYWHEEL (F)

168 3-701-437-21 WASHER

HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)

M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)

Remark

– 35 –

KEY

NOTE:

• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.

• -XX and -X mean standardized parts, so they may have some difference from the original one.

• RESISTORS

All resistors are in ohms.

METAL: Metal-film resistor.

METAL OXIDE: Metal oxide-film resistor.

F: nonflammable

SECTION 8

ELECTRICAL PARTS LIST

• Items marked “*” are not stocked since they are seldom required for routine service.

Some delay should be anticipated when ordering these items.

• SEMICONDUCTORS

In each case, u: µ, for example: uA. .

: µA. .

uPA. . : µPA. .

uPB. .

: µPB. .

uPC. . : µPC. .

uPD. .

: µPD. .

• CAPACITORS uF: µF

• COILS uH: µH

When indicating parts by reference number, please include the board.

*

*

*

*

*

Ref. No.

Part No.

Description

KEY BOARD

**********

3-018-611-01 HOLDER (LCD)

3-018-612-01 PLATE, LIGHT GUIDE

3-019-149-01 PLATE, LCD

3-019-150-01 SHEET (REFLECTOR)

3-019-151-01 PLATE (LCD), GROUND

< CAPACITOR >

C901 1-163-033-00 CERAMIC CHIP 0.022uF

C902 1-165-319-11 CERAMIC CHIP 0.1uF

C903 1-165-319-11 CERAMIC CHIP 0.1uF

C904 1-163-137-00 CERAMIC CHIP 680PF 5%

< CONNECTOR >

CNP901 1-764-423-11 PIN, CONNECTOR 12P

< DIODE >

D901 8-719-420-90 DIODE MA8051-M

D902 8-719-422-64 DIODE MA8062-M

D903 8-719-422-64 DIODE MA8062-M

D904 8-719-422-64 DIODE MA8062-M

D905 8-719-422-64 DIODE MA8062-M

< IC >

IC901 8-759-443-68 IC LC75834JED

Remark

50V

50V

50V

50V

< CHIP CONDUCTOR >

JC902 1-216-295-00 SHORT 0

JC951 1-216-296-00 SHORT 0

JC952 1-216-296-00 SHORT 0

< LIQUID CRYSTAL DISPLAY >

LCD901 1-801-966-11 DISPLAY PANEL, LIQUID CRYSTAL

< SWITCH >

LSW901 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (OFF)

LSW902 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (SOURCE)

LSW903 1-762-619-11 SWITCH, KEY BOARD (WITH LED)

(MODE *)

LSW904 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (+ + ))

LSW905 1-762-619-11 SWITCH, KEY BOARD (WITH LED) ( = 0 –)

Ref. No.

Part No.

Description Remark

LSW906 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (–)

LSW907 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (SEL)

LSW908 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (+)

LSW909 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (ATT)

LSW911 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (BTM)

LSW912 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (LCL)

LSW921 1-762-619-11 SWITCH, KEY BOARD (WITH LED) ( 6)

LSW922 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (1/INTRO)

LSW923 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (2/REPEAT)

LSW924 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (3)

LSW925 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (6/BL SKIP)

LSW926 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (5/ATA)

LSW927 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (4/MTL)

LSW930 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (DSPL)

< PILOT LAMP >

PL901 1-517-633-21 LAMP, PILOT (LCD BACK LIGHT)

PL902 1-517-633-21 LAMP, PILOT (LCD BACK LIGHT)

< RESISTOR >

R901 1-216-647-11 METAL CHIP

R902 1-216-647-11 METAL CHIP

R903 1-216-647-11 METAL CHIP

R904 1-216-651-11 METAL CHIP

R905 1-216-655-11 METAL CHIP

R906 1-216-655-11 METAL CHIP

R907 1-216-659-11 METAL CHIP

R908 1-216-663-11 METAL CHIP

R911 1-208-806-11 RES, CHIP

R921 1-216-647-11 METAL CHIP

R922 1-216-647-11 METAL CHIP

R923 1-216-647-11 METAL CHIP

R924 1-216-651-11 METAL CHIP

R925 1-216-655-11 METAL CHIP

R926 1-216-655-11 METAL CHIP

R941 1-216-667-11 METAL CHIP

R942 1-216-671-11 METAL CHIP

R951 1-216-190-00 RES, CHIP

R952 1-216-089-00 RES, CHIP

R953 1-216-049-11 RES, CHIP

R954 1-216-049-11 RES, CHIP

R955 1-216-049-11 RES, CHIP

680

680

680

1K

1.5K

1.5K

2.2K

3.3K

10K

680

680

680

1K

1.5K

1.5K

4.7K

6.8K

470

47K

1K

1K

1K

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

2% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

5%

5%

5%

5%

5%

1/8W

1/10W

1/10W

1/10W

1/10W

– 36 –

KEY MAIN

C17

C18

C19

C22

C23

C11

C12

C13

C14

C16

C6

C7

C8

C9

C10

C1

C2

C3

C4

C5

Ref. No.

Part No.

*

*

R956

R962

R963

R964 1-216-035-00 METAL CHIP

R965 1-216-035-00 METAL CHIP

R967 1-216-035-00 METAL CHIP

R968 1-216-033-00 METAL CHIP

R981 1-216-655-11 METAL CHIP

R982

R983

R984

R999

Description

1-216-049-11 RES, CHIP

1-216-025-00 RES, CHIP

1-216-033-00 METAL CHIP

1-216-663-11 METAL CHIP

1-216-671-11 METAL CHIP

1-216-081-00 METAL CHIP

1-216-308-00 METAL CHIP

3-009-809-01 BRACKET (IC)

3-010-517-01 HEAT SINK (BUS NON) (E)

7-685-793-09 SCREW +PTT 2.6X8 (S)

< CAPACITOR >

1K

100

220

270

270

270

220

1.5K

3.3K

6.8K

22K

4.7

5%

5%

5%

Remark

1/10W

1/10W

1/10W

5%

5%

5%

5%

1/10W

1/10W

1/10W

1/10W

0.5% 1/10W

0.5% 1/10W

0.5% 1/10W

5%

5%

1/10W

1/10W

*

< SWITCH >

SW951 1-762-937-11 SWITCH, ROTARY (D-BASS)

************************************************************

A-3313-396-A MAIN BOARD, COMPLETE

*********************

Ref. No.

Part No.

Description

C124 1-164-004-11 CERAMIC CHIP 0.1uF

C151 1-163-037-11 CERAMIC CHIP 0.022uF

10% 25V

C152 1-124-257-00 ELECT

C161 1-126-160-11 ELECT

C162 1-126-160-11 ELECT

C168 1-126-157-11 ELECT

2.2uF

1uF

1uF

C163 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V

C164 1-163-037-11 CERAMIC CHIP 0.022uF

10% 25V

C165 1-126-157-11 ELECT 10uF 20% 16V

C166 1-164-492-11 CERAMIC CHIP 0.15uF

10% 16V

C167 1-164-492-11 CERAMIC CHIP 0.15uF

10% 16V

10uF

C169 1-163-227-11 CERAMIC CHIP 10PF


C171 1-126-163-11 ELECT

C181

C202

1-126-163-11 ELECT

1-163-263-11 CERAMIC CHIP

4.7uF

4.7uF

C183 1-163-251-11 CERAMIC CHIP 100PF

C191 1-163-251-11 CERAMIC CHIP 100PF

C201 1-163-263-11 CERAMIC CHIP 330PF

330PF

10%

20%

20%

20%

Remark

25V

50V

50V

50V

20% 16V

0.5PF

50V

5%

20% 50V

C172 1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

20%

C182 1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

5%

5%

5%

5%

50V

50V

50V

50V

50V

50V

1-163-235-11 CERAMIC CHIP 22PF

1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

1-126-933-11 ELECT

1-126-157-11 ELECT

1-126-933-11 ELECT

100uF

10uF

100uF

1-164-232-11 CERAMIC CHIP 0.01uF


5%

20%

20%

20%

50V

10V

16V

10V

50V

50V


1-163-251-11 CERAMIC CHIP 100PF 5%

50V

50V

1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

C204 1-164-232-11 CERAMIC CHIP 0.01uF

50V

C205 1-164-489-11 CERAMIC CHIP 0.22uF

10% 16V



C208 1-126-163-11 ELECT 4.7uF

0.5PF

0.5PF

20%

50V

50V

50V

C209 1-163-251-11 CERAMIC CHIP 100PF 5% 50V

C251 1-163-037-11 CERAMIC CHIP 0.022uF

10% 25V

C252 1-124-257-00 ELECT

C261 1-126-160-11 ELECT

C262 1-126-160-11 ELECT

2.2uF

1uF

1uF

20%

20%

20%

50V

50V

50V

1-126-160-11 ELECT





1uF

0.001uF

100PF

0.01uF

20% 50V

10%

5%

50V

50V

50V

50V

1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V


10% 50V


1-124-584-00 ELECT 100uF

1-124-234-00 ELECT 22uF

20%

20%

25V

10V

16V

C25

C26

1-109-982-11 CERAMIC CHIP 1uF 10% 10V

1-163-989-11 CERAMIC CHIP 0.033uF

10% 25V

C27 1-164-222-11 CERAMIC CHIP 0.22uF

C101 1-163-263-11 CERAMIC CHIP 330PF

C102 1-163-263-11 CERAMIC CHIP 330PF

5%

5%

25V

50V

50V

C263 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V

C264 1-163-037-11 CERAMIC CHIP 0.022uF

10% 25V

C265 1-126-157-11 ELECT 10uF 20% 16V

C266 1-164-492-11 CERAMIC CHIP 0.15uF

10% 16V

C267 1-164-492-11 CERAMIC CHIP 0.15uF

10% 16V

C268 1-126-157-11 ELECT 10uF



C271 1-126-163-11 ELECT 4.7uF

20%

0.5PF

0.5PF

20%

16V

50V

50V

50V

C272 1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

C281 1-126-163-11 ELECT

C301 1-124-234-00 ELECT

C302 1-131-359-41 ELECT

4.7uF

C282 1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

C283 1-163-251-11 CERAMIC CHIP 100PF

22uF

10uF

C303 1-163-251-11 CERAMIC CHIP 100PF

C304 1-164-004-11 CERAMIC CHIP 0.1uF

20% 50V

5%

20%

10%

50V

16V

25V

5% 50V

10% 25V

C305 1-107-823-11 CERAMIC CHIP 0.47uF

10% 16V

C306 1-164-232-11 CERAMIC CHIP 0.01uF

50V

C331 1-124-584-00 ELECT 100uF 20% 10V

C104 1-164-232-11 CERAMIC CHIP 0.01uF

50V

C105 1-164-489-11 CERAMIC CHIP 0.22uF

10% 16V



C108 1-126-163-11 ELECT 4.7uF

0.5PF

0.5PF

20%

50V

50V

50V


C121 1-163-809-11 CERAMIC CHIP 0.047uF

10% 25V

C122 1-164-492-11 CERAMIC CHIP 0.15uF

10% 16V

C123 1-164-004-11 CERAMIC CHIP 0.1uF

10% 25V

C332 1-124-234-00 ELECT 22uF

C353 1-163-251-11 CERAMIC CHIP 100PF

C354 1-126-157-11 ELECT

C355 1-126-157-11 ELECT

C356

C357

1-126-934-11 ELECT


10uF

10uF

220uF

100PF

20% 16V

5%

20%

5%

50V

20% 16V

20% 16V

16V

50V

– 37 –

MAIN

Ref. No.

Part No.

Description Remark Ref. No.

Part No.


C359 1-164-489-11 CERAMIC CHIP 0.22uF

10% 16V



5%

5%

50V

50V

C503

C504

1-124-584-00 ELECT




100uF

0.1uF

C505 1-163-077-00 CERAMIC CHIP 0.1uF

C551 1-125-701-11 DOUBLE LAYER 0.047F

C552 1-124-584-00 ELECT

C553

C554



100uF

0.1uF

0.1uF

20%

10%

10%

20%

10%

10%

10V

25V

25V

5.5V

10V

25V

25V

C571 1-126-163-11 ELECT 4.7uF

20% 50V

C582 1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

C602 1-164-222-11 CERAMIC CHIP 0.22uF

C611

C612

1-126-157-11 ELECT

1-126-157-11 ELECT

10uF

10uF

C613 1-163-077-00 CERAMIC CHIP 0.1uF

C614 1-126-157-11 ELECT 10uF

C615 1-126-157-11 ELECT

C616

C617

1-126-157-11 ELECT

1-126-157-11 ELECT

10uF

10uF

10uF

C621 1-126-157-11 ELECT 10uF

C622 1-163-133-00 CERAMIC CHIP 470PF

C623 1-124-589-11 ELECT

C701

C702



47uF

0.1uF

0.1uF

C703 1-163-077-00 CERAMIC CHIP 0.1uF

C751 1-126-096-11 ELECT 10uF

C752 1-107-682-11 CERAMIC CHIP 1uF

C754

C755

1-126-157-11 ELECT

1-126-096-11 ELECT

10uF

10uF

20%

20%

10%

20%

20%

20%

20%

20%

5%

20%

10%

10%

10%

20%

10%

20%

20%

25V

16V

16V

25V

16V

16V

16V

16V

16V

50V

16V

25V

25V

25V

35V

16V

16V

35V

C781 1-126-936-11 ELECT 3300uF 20% 16V


C783 1-163-181-00 CERAMIC CHIP 100PF

C785

C786

0.1uF

0.1uF

C901 1-163-251-11 CERAMIC CHIP 100PF

C903 1-163-251-11 CERAMIC CHIP 100PF

C904 1-163-251-11 CERAMIC CHIP 100PF

5%

5%

5%

5%

50V

50V

50V

50V

50V

50V

D1

D21

D91 8-719-420-90 DIODE MA8051-M

D301 8-719-404-49 DIODE MA111

D351 8-719-035-91 DIODE MA4091-H (TA)

D352

D501

8-719-404-49 DIODE MA111

8-719-400-20 DIODE MA152WA

D551 8-719-400-20 DIODE MA152WA

D552 8-719-404-49 DIODE MA111

D553 8-719-404-49 DIODE MA111

D571

D572

D582 8-719-057-80 DIODE MA8160-M-TX

D583 8-719-422-76 DIODE MA8075-M

D601 8-719-423-32 DIODE MA8120-M

D621

D622

8-719-035-54 DIODE MA4039-M (TA)

8-719-911-19 DIODE 1SS119

D701 8-719-035-77 DIODE MA4068-L (TA)

D702 8-719-035-77 DIODE MA4068-L (TA)

D703 8-719-035-74 DIODE MA4062-M (TA)

D704

D705

D706 8-719-035-74 DIODE MA4062-M (TA)

D707 8-719-034-94 DIODE MA4180-M (QZ)

D708 8-719-035-74 DIODE MA4062-M (TA)

D709

D721

8-719-035-74 DIODE MA4062-M (TA)

8-719-970-02 DIODE 1SR139-400

D722 8-719-970-02 DIODE 1SR139-400

D723 8-719-970-02 DIODE 1SR139-400

D724 8-719-970-02 DIODE 1SR139-400

D731

D732

D733 8-719-970-02 DIODE 1SR139-400

D734 8-719-970-02 DIODE 1SR139-400

D781 8-719-049-38 DIODE 1N5404TU

D782

D783

Description

< DIODE >

8-719-991-65 DIODE SB02W03C

8-719-423-10 DIODE MA8100-M-TX

8-719-034-94 DIODE MA4180-M (QZ)

8-719-110-03 DIODE RD7.5ESB2

8-719-035-74 DIODE MA4062-M (TA)

8-719-035-74 DIODE MA4062-M (TA)

8-719-970-02 DIODE 1SR139-400

8-719-970-02 DIODE 1SR139-400

8-719-970-02 DIODE 1SR139-400

8-719-970-02 DIODE 1SR139-400

D784 8-719-422-64 DIODE MA8062-M

C906 1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

C907 1-163-009-11 CERAMIC CHIP 0.001uF

10% 50V

C908 1-163-251-11 CERAMIC CHIP 100PF

C909 1-163-181-00 CERAMIC CHIP 100PF

C910 1-163-251-11 CERAMIC CHIP 100PF

5%

5%

5%

50V

50V

50V

C911

C912



100PF 5%

0.0033uF 10%

C913 1-164-004-11 CERAMIC CHIP 0.1uF

C914 1-164-004-11 CERAMIC CHIP 0.1uF

10%

10%

50V

50V

25V

25V

IC301

IC331

IC351 8-759-395-97 IC MM1322XFBE

IC501 8-759-493-99 IC uPD17707GC-529-3B9

IC551 8-759-363-81 IC XC61AN4002PR

IC611

< IC >

8-752-079-78 IC CXA2509AQ-T4

8-759-443-67 IC LC75373ED

8-759-347-49 IC BA3918-V2

IC751 8-759-490-48 IC HA13158

< CONNECTOR >

< JACK >

CN301 1-766-260-11 CONNECTOR, FFC/FPC (ZIF) 7P

* CN351 1-506-995-11 PIN, CONNECTOR (PC BOARD) 13P

CN701 1-764-422-11 PLUG, CONNECTOR 12P

CN781 1-774-701-11 PIN, CONNECTOR 16P

J1

J561

1-764-808-14 JACK (ANT) (ANT IN)

1-566-822-41 JACK (REMOTE IN)

< CHIP CONDUCTOR >

< CONPOSITION CIRCUIT BLOCK >

CP1 1-519-504-11 GAP, DISCHARGE

JC1

JC2

JC4

1-216-296-00 SHORT 0

1-216-295-00 SHORT 0

1-216-296-00 SHORT 0

Remark

– 38 –

MAIN

Remark Ref. No.

Part No.

Description

JC151 1-216-296-00 SHORT 0

JC161 1-216-295-00 SHORT 0

JC162 1-216-295-00 SHORT 0

JC163 1-216-296-00 SHORT 0

JC251 1-216-296-00 SHORT 0

JC301 1-216-295-00 SHORT 0

JC302 1-216-295-00 SHORT 0

JC303 1-216-295-00 SHORT 0

JC304 1-216-296-00 SHORT 0

JC331 1-216-296-00 SHORT 0

JC351 1-216-295-00 SHORT 0

JC501 1-216-296-00 SHORT 0

JC502 1-216-295-00 SHORT 0

JC503 1-216-296-00 SHORT 0

JC504 1-216-296-00 SHORT 0

JC506 1-216-296-00 SHORT 0

JC507 1-216-296-00 SHORT 0

JC508 1-216-296-00 SHORT 0

JC561 1-216-295-00 SHORT 0

JC581 1-216-296-00 SHORT 0

JC601 1-216-296-00 SHORT 0

JC611 1-216-296-00 SHORT 0

JC751 1-216-296-00 SHORT 0

JC752 1-216-296-00 SHORT 0

JC781 1-216-295-00 SHORT 0

JC902 1-216-295-00 SHORT 0

JC903 1-216-295-00 SHORT 0

JC904 1-216-295-00 SHORT 0

< COIL >

L501 1-410-509-11 INDUCTOR 10uH

L781 1-411-669-12 COIL, CHOKE

L901 1-410-509-11 INDUCTOR 10uH

< TRANSISTOR >

Q21

Q22

8-729-120-28 TRANSISTOR 2SC1623-L5L6

8-729-021-94 TRANSISTOR 2SK1657-T1B

Q171 8-729-920-21 TRANSISTOR DTC314TKH04




Q351 8-729-015-11 TRANSISTOR 2SD1802FAST-TL

Q352 8-729-027-23 TRANSISTOR DTA114EKA-T146

Q353 8-729-900-53 TRANSISTOR DTC114EK

Q354 8-729-106-60 TRANSISTOR 2SB1115A



Q571 8-729-120-28 TRANSISTOR 2SC1623-L5L6


Q582 1-801-806-11 TRANSISTOR DTC144EKA-T146


Q601 8-729-423-99 TRANSISTOR 2SD2137-OP




Q622 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Remark

R7

R8

R9

R10

R11

R1

R3

R4

R5

R6

Ref. No.

Part No.

Description

< RESISTOR >

1-216-049-11 RES, CHIP

1-216-061-00 METAL CHIP

1-249-429-11 CARBON

1-216-081-00 METAL CHIP

1-249-429-11 CARBON

1-216-109-00 METAL CHIP

1-247-899-11 CARBON

1-216-180-00 RES, CHIP

1-216-073-00 METAL CHIP

1-249-413-11 CARBON

R12

R13

R14

R21

R22

R23

R24

R105

1-216-073-00 METAL CHIP

1-216-049-11 RES, CHIP

1-216-049-11 RES, CHIP

1-216-049-11 RES, CHIP

1-216-198-00 RES, CHIP

1-216-053-00 METAL CHIP

1-249-421-11 CARBON

R103 1-216-041-00 METAL CHIP

R104 1-216-109-00 METAL CHIP

1-216-077-00 METAL CHIP

R106 1-216-079-00 METAL CHIP

R107 1-249-429-11 CARBON

R108 1-216-081-00 METAL CHIP

R121 1-216-200-11 RES, CHIP

R122 1-216-081-00 METAL CHIP

R151 1-216-049-11 RES, CHIP

R152 1-216-089-00 RES, CHIP

R161 1-216-061-00 METAL CHIP

R171 1-216-033-00 METAL CHIP

R172 1-216-073-00 METAL CHIP

10K

1K

1K

1K

1K

1.5K

2.2K

470

330K

15K

1K

3.3K

10K

22K

10K

330K

680K

180

10K

470

R173

R174

R175

R181

R182

R191

1-216-081-00 METAL CHIP

1-216-129-00 METAL CHIP

1-216-089-00 RES, CHIP

1-216-033-00 METAL CHIP

1-216-073-00 METAL CHIP

R183 1-216-081-00 METAL CHIP

R184 1-216-129-00 METAL CHIP

R185 1-216-089-00 RES, CHIP

R186 1-216-182-00 RES, CHIP

1-216-073-00 METAL CHIP

R192 1-216-097-00 RES, CHIP

R203 1-216-041-00 METAL CHIP

R204 1-216-109-00 METAL CHIP

R205 1-216-077-00 METAL CHIP

R206 1-216-079-00 METAL CHIP

R207 1-216-222-00 RES, CHIP

R208 1-216-081-00 METAL CHIP

R251 1-216-049-11 RES, CHIP

R252 1-216-089-00 RES, CHIP

R261 1-216-061-00 METAL CHIP

22K

2.2M

47K

220

10K

22K

2.2M

47K

220

10K

18K

10K

22K

1.2K

22K

1K

47K

3.3K

220

10K

R271 1-216-033-00 METAL CHIP

R272 1-216-073-00 METAL CHIP

R273 1-216-081-00 METAL CHIP

R274 1-216-129-00 METAL CHIP

R275

R281

1-216-089-00 RES, CHIP

1-216-033-00 METAL CHIP

220

10K

22K

2.2M

47K

220

100K

470

330K

15K

18K

10K

22K

1K

47K

3.3K

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/8W

1/10W

1/10W

1/4W

1/10W

1/8W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/8W

1/10W

1/4W

1/10W

1/10W

1/10W

1/10W

1/10W

1/4W

1/10W

1/4W

1/10W

1/4W

1/8W

1/10W

1/4W

1/10W

1/10W

1/10W

1/10W

1/10W

1/8W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

– 39 –

MAIN

Ref. No.

Part No.

Description

R282 1-216-073-00 METAL CHIP

R283 1-216-081-00 METAL CHIP

R284 1-216-129-00 METAL CHIP

R285 1-216-089-00 RES, CHIP

R286 1-216-033-00 METAL CHIP

R301 1-216-079-00 METAL CHIP

R302 1-216-097-00 RES, CHIP

R303 1-216-065-00 METAL CHIP

R304 1-216-077-00 METAL CHIP

R305 1-249-429-11 CARBON

R306 1-249-429-11 CARBON

R307 1-216-073-00 METAL CHIP

R308 1-216-105-00 RES, CHIP

R331 1-249-393-11 CARBON

R351 1-216-049-11 RES, CHIP

R352 1-249-385-11 CARBON

R353 1-216-065-00 METAL CHIP

R354 1-216-073-00 METAL CHIP

R501 1-216-097-00 RES, CHIP

R502 1-216-097-00 RES, CHIP

R503 1-216-097-00 RES, CHIP

R504 1-216-097-00 RES, CHIP

R505 1-216-097-00 RES, CHIP

R506 1-216-057-00 METAL CHIP

R507 1-216-057-00 METAL CHIP

R508 1-216-057-00 METAL CHIP

R509 1-216-073-00 METAL CHIP

R510 1-249-429-11 CARBON

R513 1-216-699-11 METAL CHIP

R514 1-216-699-11 METAL CHIP

R516 1-216-097-00 RES, CHIP

R517 1-216-097-00 RES, CHIP

R518 1-216-097-00 RES, CHIP

R520 1-216-097-00 RES, CHIP

R522 1-216-097-00 RES, CHIP

R523 1-216-097-00 RES, CHIP

R524 1-216-097-00 RES, CHIP

R525 1-216-097-00 RES, CHIP

R526 1-216-097-00 RES, CHIP

R527 1-216-097-00 RES, CHIP

R528 1-216-097-00 RES, CHIP

R530 1-216-097-00 RES, CHIP

R532 1-216-097-00 RES, CHIP

R534 1-216-097-00 RES, CHIP

R535 1-216-097-00 RES, CHIP

R536 1-216-246-00 RES, CHIP

R537 1-216-246-00 RES, CHIP

R538 1-216-097-00 RES, CHIP

R539 1-216-097-00 RES, CHIP

R540 1-249-421-11 CARBON

R541 1-249-421-11 CARBON

R542 1-249-421-11 CARBON

R543 1-249-421-11 CARBON

R544 1-216-057-00 METAL CHIP

R545 1-249-429-11 CARBON

R546 1-249-413-11 CARBON

R551 1-216-097-00 RES, CHIP

R552 1-216-057-00 METAL CHIP

100K

100K

100K

100K

100K

100K

100K

100K

100K

100K

100K

100K

100K

100K

2.2K

2.2K

2.2K

10K

10K

100K

10K

10K

10K

220K

10

1K

2.2

4.7K

10K

100K

10K

22K

2.2M

47K

220

18K

100K

4.7K

15K

2.2K

2.2K

2.2K

2.2K

2.2K

10K

470

100K

2.2K

100K

100K

100K

100K

100K

100K

100K

100K

100K

100K

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

Remark Ref. No.

Part No.

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/4W

1/4W

1/10W

1/10W

1/4W

1/10W

1/6W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/4W

0.5% 1/10W

0.5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

Description

R561 1-208-806-11 RES, CHIP

R562

R563

R573

R574

R601

R602

R702

R703

R707

R708

R722

R723

R733

R734

1-208-806-11 RES, CHIP

1-216-025-00 RES, CHIP

R564 1-216-025-00 RES, CHIP

R571 1-216-097-00 RES, CHIP

R572 1-216-089-00 RES, CHIP

1-216-089-00 RES, CHIP

1-249-421-11 CARBON

R575 1-216-073-00 METAL CHIP

R585 1-216-113-00 METAL CHIP

R586 1-216-073-00 METAL CHIP

1-249-393-11 CARBON

1-249-395-11 CARBON

R603 1-216-186-00 RES, CHIP

R621 1-216-065-00 METAL CHIP

R701 1-216-025-00 RES, CHIP

1-216-025-00 RES, CHIP

1-216-057-00 METAL CHIP

R704 1-216-057-00 METAL CHIP

R705 1-216-057-00 METAL CHIP

R706 1-216-206-00 RES, CHIP

1-216-049-11 RES, CHIP

1-208-806-11 RES, CHIP

R709 1-208-806-11 RES, CHIP

R710 1-216-025-00 RES, CHIP

R721 1-216-296-00 SHORT

1-216-296-00 SHORT

1-216-296-00 SHORT

R724 1-216-296-00 SHORT

R731 1-216-296-00 SHORT

R732 1-216-296-00 SHORT

1-216-296-00 SHORT

1-216-296-00 SHORT

R751 1-216-198-00 RES, CHIP

R752 1-216-049-11 RES, CHIP

R781 1-216-049-11 RES, CHIP

< TUNER >

TU1

10K

10K

100

100

100K

47K

47K

2.2K

10K

470K

10K

10

15

330

4.7K

100

100

2.2K

2.2K

2.2K

2.2K

1K

10K

10K

100

0

0

0

0

0

0

0

0

1K

1K

1K

A-3282-031-A TUNER UNIT TUX-006/2 (EE)

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

Remark

0.50% 1/10W

0.50% 1/10W

5% 1/10W

5%

5%

5%

1/10W

1/10W

1/10W

1/10W

1/4W

1/10W

1/10W

1/10W

1/4W

1/4W

1/8W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/8W

5% 1/10W

0.50% 1/10W

0.50% 1/10W

5% 1/10W

1/8W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

1/10W

S501

S551

< SWITCH >

1-571-478-11 SWITCH, SLIDE (POWER SELECT)

1-692-431-21 SWITCH, TACTILE (RESET)

1/10W

1/8W

1/8W

1/10W

1/10W

1/4W

1/4W

1/4W

1/4W

1/10W

< VIBRATOR >

X501 1-567-713-11 VIBRATOR, CRYSTAL (4.5MHz)

************************************************************

9

F781

MISCELLANEOUS

***************


1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)

HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)

M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)

************************************************************ 1/4W

1/4W

1/10W

1/10W

– 40 –

Ref. No.

Part No.

Description Remark

#1

#2

#3

#4

#5

**************

HARDWARE LIST

**************

7-621-772-10 SCREW +B 2X4

7-685-793-09 SCREW +PTT 2.6X8 (S)

7-685-792-09 SCREW +PTT 2.6X6 (S)

7-685-794-09 SCREW +PTT 2.6X10 (S)

7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT

#6

#7

7-624-104-04 STOP RING 2.0, TYPE-E

7-627-553-17 PRECISION SCREW +P 2X2 TYPE 3

************************************************************

ACCESSORIES & PACKING MATERIALS

********************************

1-473-067-71 REMOTE COMMANDER (RM-X4S)

3-861-693-11 MANUAL, INSTRUCTION

(HUNGARIAN, RUSSIAN)

3-861-694-11 MANUAL, INSTRUCTION, INSTALL

(HUNGARIAN, RUSSIAN)

3-921-278-01 LABEL (DSPL) (for RM-X4S)

X-3373-412-1 CASE (PANEL) ASSY (for FRONT PANEL)

************************************************************

501

502

503

504

505

PARTS FOR INSTALLATION AND CONNECTIONS

***************************************

3-916-161-31 FRAME ASSY

X-3370-077-1 SCREW ASSY (AE. KEY), FITTING

X-3371-913-1 SCREW ASSY (J)

X-3373-432-1 BRACKET ASSY (For RM-X4S)


501

502

503 504

505

– 41 –

XR-4803

9-925-681-11

Sony Corporation

Personal & Mobile Communication Company

– 42 –

98A05076-1

Printed in Japan © 1998. 1

Published by Quality Assurance Dept.

No results