advertisement
2-190-733-11 (1)
SRP-X500P Manager
User’s Guide
Software Version 1.0
Before using the software, please read this User’s Guide and the Operating Instructions of the
SRP-X500P Digital Powered Mixer thoroughly and retain them for future reference.
SRP-X500P
© 2004 Sony Corporation
2
Table of Contents
Overview.................................................................................3
Features ...................................................................................... 3
Using the supplied CD-ROM..................................................... 3
Operating conditions .................................................................. 3
Preparation.............................................................................4
Installing the SRP-X500P Manager ........................................... 4
Uninstalling ................................................................................ 4
Names and Functions of Controls on Screen.....................5
Common operation section ........................................................ 5
BLOCK screen ........................................................................... 6
PANEL VIEW screen ................................................................ 9
OVER VIEW screen ................................................................ 10
REMOTE FADER screen ........................................................ 15
PARALLEL/PROJECTOR CONTROL screen....................... 16
SCENE MEMORY screen....................................................... 18
About the Mixer’s Internal Preset Memory........................ 19
SYSTEM TYPE preset memory .............................................. 19
PROJECTOR PROTOCOL preset memory ............................ 20
To Control the Projector Whose Protocol Is Not Preset to the Mixer ........................................................................ 21
Appendix .............................................................................. 25
Factory settings (SYSTEM TYPE 0)....................................... 25
Overview
Features
The SRP-X500P Manager is a program which allows you to make parameter settings for the SRP-X500P Digital
Powered Mixer.
Various effector settings
Detailed settings on equalizer, automatic gain control, compressor, etc. can be performed. The SRP-X500P
Manager is provided with visual aids including graphs to allow easy operation.
Remote settings
Settings for the REMOTE PARALLEL connector on the rear of the SRP-X500P Digital Powered Mixer and settings for projector control can be performed.
Scene memory
You can store the settings as scene files to the internal memory of the SRP-X500P Digital Powered Mixer. You can change the settings at a time by recalling the scene.
Operating conditions
The recommended operating environment for using the
SRP-X500P Manager is as follows.
OS
CPU
RAM
Available hard disk space
Microsoft Windows Millennium Edition
Microsoft Windows 2000 Professional
Microsoft Windows XP Professional
Microsoft Windows XP Home Edition
Celeron 400 MHz or higher
128 MB of RAM or greater
20 MB of available hard-disk space
Notes on use
• The PC must be preinstalled with one of the OS listed above. Operation of this software when the OS has been upgraded is not guaranteed.
• Operation this software is not guaranteed in every PC, even if the recommended environment is satisfied.
Using the supplied CD-ROM
The CD-ROM contains the following files.
SRP-X500P Manager
This is a program for setting the SRP-X500P parameters from a PC.
SRP-X500P Manager User’s Guide
This is a PDF file containing information on the functions and operations of the SRP-X500P Manager. Can be viewed on a PC.
SRP-X500P Operating Instructions
This is a PDF file containing information on the functions and operations of the SRP-X500P Digital Powered Mixer.
Can be viewed on a PC.
To open these PDF files, Adobe Acrobat or Adobe Reader must be installed on your PC.
To get Adobe Reader, go to the website of Adobe Systems
Incorporated (http://www.adobe.com/).
Overview
3
Preparation
Installing the SRP-X500P Manager
1
Insert the supplied CD-ROM into the CD-ROM drive of the personal computer.
2
Open the SRP-X500P Manager \ English folder double-click the Setup icon.
“Welcome to the SRP-X500P Manager setup wizard.” screen appears.
3
Click “Next”.
“Select Installation Folder.” screen appears.
Uninstalling
1
Click the Start menu and select “Settings (S)”. Then click “Control Panel” to open it.
2
Double-click the “Add/Remove Programs” icon and select “SRP-X500P Manager” from the list of the
“Install/Uninstall” tab.
3
Click “Add/Remove (R)...”.
This completes the uninstallation.
Note
When using Microsoft Windows 2000 Professional,
Microsoft Windows XP Professional or Microsoft
Windows XP Home Edition, be sure to log on as the user having administrator authority, then perform the installation or uninstallation.
Note
The SRP-X500P Manager folder is created in
C:\Program Files. To change the installation destination, click “Browse...”.
4
After specifying the installation destination, click
“Next”.
“Confirm Installation.” screen appears.
5
Click “Next”.
Installation stars.
6
After “Installation Complete.” screen appears, click
“Close”.
“Confirm Installation.” screen appears.
Installation of the SRP-X500P Manager is now complete.
4
Preparation
Names and Functions of Controls on Screen
Common operation section
The controls shown below appear on all the screens.
A Menu bar
The titles of the menus are displayed.
You can perform operations that are common to the basic settings and each setup screen.
a
File menu
This software allows you to save the parameters of up to 8 scenes and the information in a single setup file (*.x5p).
New: Creates a new setup file. Cannot be selected when communication between the SRP-X500P Manager and the SRP-X500P Digital Powered Mixer (referred to as “mixer” hereafter) is active.
Open: Opens an existing setup file. When “Open” is selected while the communication between the SRP-
X500P Manager and the mixer is active, all parameters within the current setup file is transmitted to the mixer.
Open scene: Opens the specified scene number from the
8 scenes in the existing setup file.
A Select a setup file.
B The information contained in the selected setup file is displayed.
C Select the scene number.
Names and Functions of Controls on Screen
5
D The index of the selected scene number is displayed.
E Click the Open button.
Save: Saves the new data by overwriting the existing data.
Save as: Saves the data under a different name.
Exit: Exits the SRP-X500P Manager.
b
Communication menu
Activates/deactivates the communication between the
SRP-X500P Manager and the mixer. Also specifies the port number for RS-232C communication.
Connect: Activates communication. Cannot be selected when the communication between the SRP-X500P
Manager and the mixer is already activated.
Disconnect: Deactivates communication. Cannot be selected when the communication between the SRP-
X500P Manager and the mixer is already deactivated.
Port select: Specifies the port number for RS-232C communication to be used for SRP-X500P Manager operation.
c
Options menu
Factory preset: Resets all parameters to the default settings.
Password setting: You can set a password.
A Enter a password.
B For confirmation, enter the same password again.
C Click “OK”.
Note
If you enter the wrong password, you cannot start the SRP-
X500P Manager. Be sure to take a note of the password.
If you forget the password, uninstall the software and then reinstall it from the supplied CD-ROM.
d
Help menu
About: The version of the software appears.
B Screen selection tabs
Click to select the setup screen for each parameter.
C CONNECTION indicator
Lights up green when the communication between the
SRP-X500P Manager and the mixer is activated.
BLOCK screen
The BLOCK screen shows the internal block diagram of the mixer. You can click the button to turn each function on or off while monitoring overall settings on this screen.
6
Names and Functions of Controls on Screen
A MIC INPUT setting section a
Indicators
These are the indicators of microphone input.
RF: Lights up green when the RF signal is input to the wireless tuner unit which is installed in the mixer.
AF: Lights up yellow when the audio signal is input to the wireless tuner unit which is installed in the mixer.
WL: Lights up green when the signal is input to the mixer from the wireless tuner unit installed to the mixer. As long as this indicator is lit, the mixer selects the signal input from the wireless tuner unit.
+48V: Lights up red when the +48 V ON/OFF switch on the mixer is set to ON.
b
Index name input box
You can enter an index name for each input channel. Up to eight alphanumeric characters can be entered.
c
TRIM indication
Displays the reference level of the input channel specified by the TRIM control on the mixer within the range of –60 dBu to –30 dBu.
d
Level meter
Displays the signal level of the input channel.
e
LCF, FR/EQ, and AGC buttons
Click to turn each function on or off. The button lights up green when it is set to on.
f
MUTING button
Left-click to turn muting function on or off. The button lights up red when it is set to on.
g
Fader level indication
Displays the fader level of the input signal. The displayed value is the summation of the level of the INPUT fader and remote fader specified by the software and the input level control setting on the mixer.
Names and Functions of Controls on Screen
7
B LINE, AV/RGB INPUT setting section a
TRIM indication
Displays reference level specified by the TRIM control on the mixer.
b
Level meter
Displays the signal level of each input channel.
c
AV/RGB SELECTOR buttons
Click to select one of the AV/RGB channels (A to E). The button for the selected channel lights up green.
d
SIGNAL DEFINE indication
Displays the signal format specified in the PROJECTOR
CONTROL setting section of the REMOTE PARALLEL/
PROJECTOR CONTROL screen.
e
PROJECTOR PROTOCOL indication
Displays the projector protocol setting specified by the
PROJECTOR PROTOCOL selector on the mixer and model name of the projector.
For details on the MUTING button, fader level indication,
entering the index name for the input signal, see “A MIC
INPUT setting section” of the BLOCK screen (page 7).
C ROUTING setting section
With this section, you can select an output path for each input signal by assigning each input channel to an output channel.
Left-click a channel button to turn the corresponding channel on or off. Right-click the button to specify the sending level of the input signal to the output channel.
When the channel button is set to on and the sending level is set to 0 dB, it lights up green. The button lights up blue when it is set to on and the sending level is set to –3 dB to
–20 dB.
D OUTPUT setting section a
DELAY button
Click to turn the delay on or off. The button lights up green when the delay is set to on.
8
Names and Functions of Controls on Screen
Note
The total amount of delay time to be set for the total output channel must not exceed 160 ms (54.7 m or 181.9 feet).
For details, see “DELAY amount setup box” (page 13).
b
PROTECTION indicator
Lights up red when the PROTECTION indicator on the mixer lights up red.
c
ATT indication
Shows the attenuation level specified by the SPEAKER
OUT controls on the mixer.
d
CLIP indicator
Lights up red when the CLIP indicator on the mixer lights up red.
e
LINK check box
Check the muting, compressor, delay, and output fader settings for the SPEAKER 1 and 2, SPEAKER 3 and 4,
LINE 1 and 2, or LINE 3 and 4 to link with each other.
f
70V LINE check box
Check to set the SPEAKER 3 and 4 channels to 70V LINE.
PANEL VIEW screen
The PANEL VIEW screen shows the settings performed through the front panel of the mixer and the system type setting,
A FRONT PANEL VIEW display section
Shows the settings performed through the front panel of the mixer.
If you save the current status of this section to the setup file, position of the controls and switches of the mixer can be recalled later. Then, by setting the controls and switches so that the markers representing them on the screen light up green, the front panel status can be easily reproduced.
B SYSTEM TYPE display section
Shows the image of the system type specified by the
SYSTEM TYPE selector on the front panel of the mixer.
C PROJECTOR PROTOCOL display section
Displays the projector number specified by the
PROJECTOR PROTOCOL selector on the front panel of the mixer and index name of the projector.
D INFORMATION input section
Up to 128 alphanumeric characters can be entered.
Names and Functions of Controls on Screen
9
OVER VIEW screen
The detailed settings on equalizer, automatic gain control, etc., for each channel can be performed.
A MIC INPUT setting section a
TRIM indication
Displays the reference level of the input channel specified by the TRIM control on the mixer within the range of –60 dBu to –30 dBu.
b
Level meter
Displays the signal level of the input channel.
c
Indicators
These are the indicators of microphone input.
RF: Lights up green when the RF signal is input to the wireless tuner unit which is installed in the mixer.
AF: Lights up yellow when the audio signal is input to the wireless tuner unit which is installed in the mixer.
WL: Lights up green when the signal is input to the mixer from the wireless tuner unit installed to the mixer. As long as this indicator is lit, the mixer selects the signal input from the wireless tuner unit.
+48V: Lights up red when the +48 V ON/OFF switch on the mixer is set to ON.
d
Index name indication
Shows the index name of the input channel entered in index name column of the BLOCK screen.
e
AGC (Automatic Gain Control) button
Left-click to display the AUTO GAIN CONTROL setting screen.
10
Names and Functions of Controls on Screen
K GAIN CONTROL indication
Shows the amount of gain control obtained by the
AGC function.
L CLOSE button
Click to close the AUTO GAIN CONTROL setting screen.
f
FR/EQ (Feedback Reducer/Equalizer) button
Left-click to display the MIC INPUT EQUALIZER setting screen.
A Characteristics graph
Displays the characteristics of the automatic gain control. By dragging the marker with the mouse, threshold level and ratio of the compressor and threshold level of the gate can be changed.
B ON button
Click to turn the automatic gain control on or off.
When set to on, this button lights up green.
C COMPRESSOR THRESHOLD setup box
Specifies the threshold level of the compressor. The level can be set within the range of –60 dB to +20 dB, in 1-dB steps.
D RATIO setup box
Specifies the ratio of the compressor. The value can be set within the range of 1 : 1 to
∞
: 1, in 14 steps.
E MAKE GAIN setup box
Specifies the make up gain value. The value can be set within the range of 0 dB to +10 dB, in 1-dB steps.
F GATE THRESHOLD setup box
Specifies the threshold level of the gate. The value can be set within the range of –60 dB to 0 dB, in 1-dB steps.
G RANGE setup box
Specifies the range of the gate. The value can be set within the range of –60 dB to 0 dB, in 1-dB steps.
H ATTACK setup box
Specifies the attack time. The value can be set within the range of 0.1 ms to 33000 ms, in 32 steps.
I HOLD TIME setup box
Specifies the hold time. The value can be set within the range of 0.1 ms to 33000 ms, in 32 steps.
J RELEASE setup box
Specifies the release time. The value can be set within the range of 0.1 ms to 33000 ms, in 32 steps.
A Channel selection button
Selects the input channel that you want to set. The selected button lights up yellow. To select the other channel, left-click the corresponding button.
B Equalizer pattern graph
Appears when “EQ” is selected on the FR/EQ selection radio button.
The markers with the same color as the corresponding band in the EQ parameter appear on the graph. You can change the gain and frequency for each band by dragging the corresponding marker with the mouse.
Right-clicking the marker returns the gain to 0 dB.
You can also change the Q value by rolling the center wheel of the mouse up or down.
C LCF (low-cut filter) button
Each click on this button toggles the low-cut filter between on and off. This button lights up green when set to on. The low-cut filter reduces low-frequency components such as blowing noise and makes the sound clearer.
D FR/EQ button
Each click on this button toggles the feedback reducer or equalizer between on and off. This button lights up green when set to on.
E FR/EQ selection radio buttons
Names and Functions of Controls on Screen
11
Click “FR” or “EQ” to select the function of equalizer as the feedback reducer or the parametric equalizer.
FR: The feedback reducer setting screen appears.
When “FR” is selected, the EQ parameter 1 to 5 columns become inactive and FR SETUP button becomes active.
EQ: The 5-band parametric equalizer setting screen appears. When “EQ” is selected, the EQ parameter
1 to 5 columns become active and FR SETUP button becomes inactive.
Note
Changing the parametric equalizer setting will cancel the howling suppression. When you use the equalizer as the parametric equalizer, make the setting carefully not to affect the howling suppression.
F FR SETUP button
Left-click to display the channel selection dialog box.
With the dialog box, select the channel and click OK button to carry out the automatic setting of the feedback reducer (function to suppress the positive acoustic feedback by detecting the frequency that causes howling in advance and by reducing the gain of the frequency).
Note
The FR SETUP button becomes operative only when the communication between the SRP-X500P Manager and the mixer is active and “FR” is selected on the FR/
EQ selection radio buttons.
G EQ parameter setup boxes
Set the frequency, Q-value, and gain for each equalizer band. Values can be set by clicking on the S/s buttons or by entering numerical value directly.
H CLOSE button
Click to close the MIC INPUT EQUALIZER setting screen.
g
MUTING button
Left-click to turn muting function on or off. The button lights up red when it is set to on.
h
Input fader
You can adjust the input level by dragging the input fader.
The yellow triangler marker displayed on the side of the fader indicates the fader position which is the sum of the input fader setting and the input level control settings on the mixer.
B LINE, AV/RGB INPUT setting section a
Index name indication
Shows the index name of the audio signal input from the
LINE IN connectors or the AV/RGB INPUT connectors
(A to E). For the signal input from the AV/RGB INPUT connectors, the index name is displayed along with the
SELECT buttons indication (e.g., A:INDEX).
b
Level meters
Displays the signal level of each input channel.
c
TRIM indication
Displays the reference level of the input channel specified by the TRIM control on the mixer. For the signal input from the AV/RGB INPUT connectors, the reference level is displayed along with the SELECT buttons indication
(e.g., A:–3 dB).
d
SELECT buttons
Click to select one of the AV/RGB channels (A to E). The button for the selected channel lights up green.
e
MUTING button
Left-click to turn muting function on or off. The button lights up red when it is set to on.
f
Input fader
You can adjust the input level by dragging the input fader.
The yellow triangler marker displayed on the side of the fader indicates the fader position which is the sum of the input fader setting and remote fader setting on the software and the input level control settings on the mixer.
C DELAY indication section
12
Names and Functions of Controls on Screen
a
DELAY REMAIN indication
The total amount of delay time to be set for the total output channels must not exceed 160 ms (54.7 m, or 181.9 feet).
After the DELAY REMAIN indication shows 0%, the amount of delay time cannot be increased.
b
UNIT setup box
Allows you to select the unit of the delay from the following: ms, meter, feet.
D Routing setting section
With this section, you can select an output path for each input signal by assigning each input channel to an output channel.
The buttons on the first row are for the MIC INPUT channels. The buttons on the middle row are for the LINE
INPUT L/R channels, and the buttons located on the last row are for the AV/RGB INPUT L/R channels.
Left-click a channel button to turn the corresponding channel on or off. Right-click the button to specify the sending level of the input signal to the output channel.
When the channel button is set to on and the sending level is set to 0 dB, it lights up green. The button lights up blue when it is set to on and the sending level is set to –3 dB to
–20 dB.
a
DELAY button
Turns the delay time function on or off. The button lights up green when the delay is turned to on.
b
DELAY amount setup box
Allows you to select the amount of delay. The value can be set by clicking on the S/s buttons or by entering numerical value directly. The amount of delay is shown in units specified in the UNIT setup box on the DELAY indication section.
E Output channels setting section
With this section, settings related to output channels can be performed.
Note
The total amount of delay time to be set for the total output channels must not exceed 160 ms (54.7 m, or 181.9 feet).
Determine the amount of delay time by watching the
DELAY REMAIN indication on the DELAY indication section.
c
Speaker output indicators
PROTECTION: Lights up red when the PROTECTION indicator on the mixer lights up red.
CLIP: Lights up red when the CLIP indicator on the mixer lights up red.
d
ATT indication
Shows the attenuation level specified by the SPEAKER
OUT controls on the mixer.
e
70V LINE check box
Check to set the SPEAKER 3 and 4 channels to 70V LINE.
f
LINK check box
Check the parameter settings for the SPEAKER 1 and 2,
SPEAKER 3 and 4, LINE 1 and 2, or LINE 3 and 4 to link with each other.
Names and Functions of Controls on Screen
13
Notes
• Even when the LINK check box is checked, equalizer settings are not linked between the 2 channels.
• When the sum of delay amount or compressor amount exceeds the limit due to linkage of the 2 channels, a warning message appears. If this occurs, reduce the amount.
g
COMP button
Left-click to display the COMPRESSOR setting screen.
H ATTACK setup box
Specifies the attack time.
I RELEASE setup box
Specifies the release time.
J CLOSE button
Click to close the COMPRESSOR setting screen.
h
EQ button
Left-click to display the OUTPUT EQUALIZER setting screen.
A Channel selection buttons
The selected button lights up yellow. To select the other channel, left-click the corresponding button.
B ON indicator
The indicator for the channel whose compressor setting is turned on lights up green.
C Characteristics graph
Displays the characteristics of the compressor. By dragging the markers with the mouse, threshold level and ratio of the compressor can be changed.
D ON button
Left-click to turn the compressor on or off. When set to on, this button lights up green.
Note
Compressor can be simultaneously applied to up to 4 output channels.
E GAIN REDUCTION indicator
Shows the amount of attenuation of the gain.
F THRESHOLD setup box
Specifies the threshold level of the compressor.
G RATIO setup box
Specifies the ratio of the compressor.
A Channel selection buttons
The selected button lights up yellow. To select the other channel, left-click the corresponding button.
B Number of bands setup box
Use the pull-down menu to select the number of bands to set the parameters. 0, 3, 6, 9, or 12 bands can be selected. The parameter setup boxes corresponding to the selected number of bands become active.
Note
The total amount of equalizer bands to be applied to the total output channels must not exceed 24 bands.
While setting the equalizer for the output channels, be sure that the total number of equalizer bands is 24 or less.
C Equalizer pattern graph
The markers with the same color as the corresponding band in the EQ parameter appear on the graph. You can change the gain and frequency for each band by dragging the corresponding marker with the mouse.
Right-clicking the marker returns the gain to 0 dB.
You can also change the Q value by rolling the center wheel of the mouse up or down.
D ON button
14
Names and Functions of Controls on Screen
Left-click to turn the equalizer on or off. When set to
ON, this button lights up green.
E Equalizer parameter setup boxes
Set the frequency, Q-value, and gain for each equalizer band. Values can be set by clicking on the S/s buttons or by entering numerical value directly.
F CLOSE button
Click to close the OUTPUT EQUALIZER setting screen.
i
Output fader
You can adjust the output level by dragging the output fader. The yellow triangular marker displayed on the side of the fader indicates the fader position which is the sum of the output fader setting, remote fader setting, and the output level control settings on the mixer.
For details on the index name indication, level meters, and
the MUTING button, see “A MIC INPUT setting section” of the OVER VIEW screen (page 10).
REMOTE FADER screen
By assigning input/output faders to the remote faders, you can control the volume of asssined channels with single fader operation.
The level of the MASTER fader can be controlled by the
MASTER volume control on the front panel of the mixer.
The level of the REMOTE 1 to 6 faders can be controlled through the REMOTE PARALLEL connector on the rear panel of the mixer.
a
Index name input box
You can enter an index name for each remote fader. Up to eight alphanumeric characters can be entered.
b
Index name indication
Displays the index name entered in the BLOCK setting screen.
c
Fader assignment buttons
Left-click the button to assign input/output faders to the remote fader. The buttons corresponding to assigned input/ output faders light up green.
Note
Input faders and output faders cannot be assigned to the same remote fader.
Names and Functions of Controls on Screen
15
d
MUTING indicator
The indicator for the muted fader lights up red.
e
Remote fader level indication
Shows the level of the remote fader.
PARALLEL/PROJECTOR CONTROL screen
The PARALLEL/PROJECTOR CONTROL screen allows you to make settings on the REMOTE PARALLEL connector of the mixer and projector control.
A PARALLEL setting section a
PARALLEL INPUT indicators
Show the status of each input pin of the REMOTE
PARALLEL connector.
When input voltage is high: Turns off.
16
Names and Functions of Controls on Screen
When input voltage is low: Lights up green.
b
INPUT function selection section
Left-click and select the function from the pull-down menu.
The selectable functions are as follows:
INPUT
NONE
AV/RGB
SELECT
MASTER
VOLUME
REMOTE
FADER 1-6
-
OFF, A-E Switch
(momentary type)
MUTING Switch (latch type)
UP Switch
(momentary type)
DOWN Switch (latch type)
MUTING Switch (latch type)
LEVEL
Connectable device
Function
Volume
None
When turned on, selects AV/RGB
SELECT setting (OFF or A-E).
When turned on, mutes the master volume. Turn off to cancel muting.
While turned on, keeps turning up the master volume.
While turned on, keeps turning down the master volume.
When turned on, mutes the remote fader. Turn off to cancel muting.
Adjusts the remote fader volume.
SCENE
RECALL
PROJECTER
POWER
1-8
ON
Switch
(momentary type)
Switch
(momentary type)
STANDBY Switch
(momentary type)
ON/
STANDBY
Switch (latch type)
When turned on, recalls the scene memory.
When turned on, turns on the projector power.
When turned on, sets the projector to standby status.
EMG OPEN
CLOSE
Emergency broadcast system
Emergency broadcast system
When turned on, turns on the projector power. Turn off to set the projector to standby status.
When the signal from the emergency broadcast system is
OPEN, mutes all output channels.
Turn off to cancel muting.
When the signal from the emergency broadcast system is
CLOSE, mutes all output channels. Turn off to cancel muting.
c
Input level indication
Shows the input level setting on the mixer. This is indicated only when a volume controller is connected to the input pin.
d
PARALLEL OUTPUT indicators
Show the status of each output pin of the REMOTE
PARALLEL connector.
When output voltage is low: Lights up green.
When output voltage is high: Turns off.
e
OUTPUT function selection section
Left-click and select the function from the pull-down menu.
The selectable functions are as follows:
OUTPUT Function
NONE
AV/RGB
SELECT
MASTER
VOLUME
None
OFF, A-E Turns on (Low) when the corresponding channel is selected.
MUTING Turns on (Low) when the master volume is fully turned down.
MAX (UP) Turns on (Low) when the master volume is at the maximum level.
REMOTE
FADER 1-6
MIN
(DOWN)
Turns on (Low) when the master volume is at the minimum level.
MUTING Turns on (Low) when the corresponding remote fader is fully turned down.
MAX Turns on (Low) when the corresponding remote fader is at the maximum level.
SCENE
RECALL
MIN
1-8
Turns on (Low) when the corresponding remote fader is at the minimum level.
Turns on (Low) when the corresponding scene memory is recalled.
PROJECTER
POWER
ON Turns on (Low) when the projector is turned on.
STANDBY Turns on (Low) when the projector enters standby status.
EMG Turns on (Low) when all output channels are muted by the EMG setting for the input pins (either OPEN or CLOSE).
B PROJECTOR CONTROL setting section
With this section, settings related to projector control can be performed.
1 2
3
4 a
PROJECTOR PROTOCOL indication
Shows the status of the PROJECTOR PROTOCOL selector setting on the mixer and the name of the projector.
b
PROTOCOL SETTING button
Left-click to display the PROTOCOL SETTING screen.
A File menu
The projector protocol settings can be saved as a file and can be recalled later.
B INDEX name input box
You can enter an index name the projector protocol setting file. Up to 16 alphanumeric characters can be entered.
C BITS PER SECOND setup box
Use the pull-down menu to select the baud rate for the
RS-232C port for projector control.
D PARITY setup box
Use the pull-down menu to select the parity bits.
Names and Functions of Controls on Screen
17
E Command input section
Enter the commands to be sent from the mixer to the projector to turn it on, to set it to standby status, or to select the input channel. Enter the command as a hexadecimal number using numbers 0 to 9 and letters
A to F.
The maximum length of the command is 32 bytes.
F WAIT input box
Specify the wait time until the another command is sent after the projector has received the previously sent command.
G TEST button
Press to run the test on sending command.
H PROJECTOR INPUT SELECT buttons
Press one of the buttons to select the signal format, then enter the command defining the input channel on the projector for the signal format.
I COMMAND SEQUENCE indication
Shows the sequence of commands and the wait time to be sent for defining the input channel on the projector.
J CLOSE button
Click to close the PROTOCOL SETTING setting screen.
c
PROJECTOR POWER setting section
By checking the SYNC WITH POWER ON checkbox, you can interlock the power on/off control of the projector with the POWER switch operation on the SRP-X500P.
d
SIGNAL DEFINE selection radio buttons
Click to select the format of the video signal which is input to each of the AV/RGB INPUT connectors.
SCENE MEMORY screen
You can store the settings that you usually use as a scene file to internal memory of the mixer to recall it whenever you use it. Or, by storing scene files in advance, you can quickly deal with division of the room.
a
SCENE MEMORY button
Left-click to select the scene file number.
18
Names and Functions of Controls on Screen
The color of the button shows the status of the scene file number.
Green: Currently selected.
Gray: A scene file is stored.
Deep gray: No scene file is stored.
b
INDEX indication
Shows the index name of the scene file.
c
FUNCTIONS indication
The functions stored to the selected scene file light up green.
d
STORE button
Used to store the scene file. Left-click to display the setting screen to allow entering the index name and selecting the functions to be included in the scene file.
e
RECALL button
Click to recall the scene file whose number is currently selected by the SCENE MEMORY button. This button does not work when you have selected a number with no scene file is stored.
f
CLEAR button
Click to clear the scene file whose number is currently selected by the SCENE MEMORY button. This button does not work when you have selected a number with no scene file is stored.
g
POWER ON SETTING radio buttons
Click to select the scene file status to be automatically recalled when the mixer is turned on.
LAST MEMORY: The status when the power to the mixer has been turned off resumes.
SCENE No.1: The scene file No.1 is recalled.
About the Mixer’s Internal
Preset Memory
SYSTEM TYPE preset memory
By setting the SYSTEM TYPE selector on the front panel of the mixer to 1 to 9, you can choose the speaker system type setting that corresponds with the AV system being used.
Of the items included in the system type preset memory 1 to 9, the setting of the following items cannot be changed using the SRP-X500P Manager.
• MIC INPUT Low Cut Filter
• MIC INPUT FR/EQ settings
• INPUT fader
• INPUT MUTING
• ROUTING
• Number of bands of the OUTPUT equalizer
• OUTPUT compressor
• OUTPUT fader
• OUTPUT MUTING
• OUTPUT LINK
• DELAY
• 70V LINE/Lo imp. setting for the SPEAKERS CH-3/4 terminals
• REMOTE FADER
• Scene memory
To change the setting of the items above, set the SYSTEM
TYPE selector on the mixer to “0”, turn off the mixer, and then turn it on again.
For details on the settings other than the REMOTE
FADER, refer to the Operating Instructions supplied with the mixer.
The preset patterns for the REMOTE FADER are shown in the following table:
About the Mixer’s Internal Preset Memory
19
SYSTE
M TYPE
Setting
1
2
3
MIC 1-4
LINE,
AV/RGB
SP OUT 1
SP OUT 2
MASTER REMOTE
1 2 3 4 5 6
-
a a
SP OUT 3
SP OUT 4 a
-
LINE OUT 1 a
LINE OUT 2 a
LINE OUT 3 -
LINE OUT 4 -
MIC 1-4
LINE,
-
-
AV/RGB
SP OUT 1 a
SP OUT 2
SP OUT 3 a a
SP OUT 4 a
LINE OUT 1 a
LINE OUT 2 a
LINE OUT 3 -
-
a a a a -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
a -
a -
a -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
a a
a a
a -
a a -
a a -
-
a -
-
-
-
-
-
-
a a -
-
-
a a -
a a
-
-
a a
a -
a a -
a a -
-
a -
-
-
-
-
-
-
-
LINE OUT 4 -
MIC 1-4 -
LINE,
AV/RGB
SP OUT 1 a
SP OUT 2
SP OUT 3 a
-
SP OUT 4 -
LINE OUT 1 a
LINE OUT 2
LINE OUT 3
LINE OUT 4 a
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
a -
-
a -
-
-
-
-
-
-
-
a a
a a
a a -
4
5
6-9
MIC 1-4
LINE,
AV/RGB
SP OUT 1
SP OUT 2
SP OUT 3
SP OUT 4 -
LINE OUT 1 a
-
a
-
-
LINE OUT 2 a
LINE OUT 3 -
LINE OUT 4 -
MIC 1-4 -
LINE,
AV/RGB
a SP OUT 1
SP OUT 2 a
SP OUT 3
SP OUT 4 a a
LINE OUT 1 a
LINE OUT 2 a
LINE OUT 3 -
LINE OUT 4 -
MIC 1-4
LINE,
AV/RGB
-
a SP OUT 1
SP OUT 2
SP OUT 3
SP OUT 4 a a a
LINE OUT 1 a
LINE OUT 2 a
LINE OUT 3 -
LINE OUT 4 a a a
-
a -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
a -
-
-
-
-
a a
a a
-
-
-
-
-
-
-
-
-
a a a a -
-
a -
a -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
a -
a a a
-
-
a a
a a
-
-
-
-
-
-
-
-
-
a a a a -
-
a -
a -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
a -
a -
a -
a -
-
-
-
a a a a
-
-
-
a a
-
a : Assigned.
- : Not assigned.
PROJECTOR PROTOCOL preset memory
By setting the PROJECTOR PROTOCOL selector on the front panel of the mixer to 1 to A, you can choose the protocol that corresponds with the projector or display monitor to be used with the mixer.
Of the items included in the protocol 1 to A, the setting of the following items cannot be changed using the SRP-
X500P Manager.
• Index
20
About the Mixer’s Internal Preset Memory
• Baud rate
• Parity bit
• POWER ON and STANDBY commands and the wait time
• VIDEO, RGB, and COMPONENT input selection command and the wait time
The input selection command for OTHER TERMINAL is not preset to the mixer.
When you input S-video signal or etc. from the video source device directly to the projector or display monitor, specify the input command.
For details on the projector or display monitor whose protocol is preset to the mixer, refer to the Operating
Instructions supplied with the mixer.
To Control the Projector
Whose Protocol Is Not
Preset to the Mixer
Set the PROJECTOR PROTOCOL selector on the mixer to “0”, turn off the mixer, then turn it on again.
And then, make the necessary settings in the PROTOCOL
SETTING screen.
Connectable projectors
Projectors which satisfy the following specifications can be connected to the mixer.
• Equipped with RS-232C remote terminal
• Equipped with the RS-232C remote terminal supporting the following specifications:
− Electrical characteristics : Conforming to RS-232C
− Baud rate : 9600, 19200 or 38400 bps
− Parity bit : None, odd or even
− Data length : 8 bits
− Stop bit : 1 bit
− Flow control : None
The RS-232C remote terminal can be used to turn on the power, turn off the power, and select the input terminal.
Video signal systems and limitations
This system has the following limitations depending on the video signal system used and on the operation method.
The limitations are shown below.
• When component signal is used
To Control the Projector Whose Protocol Is Not Preset to the Mixer
21
The projector is equipped with the component signal input terminals.
No
,
Yes j
The component signal and the
RGB signal are used together.
No
,
Yes j
The projector has a single input terminal which accepts both the component signal and RGB signal that are switched from the RS-
232C remote terminal.
Yes k
No m
The projector has independent input terminals which accept the component signal and RGB signal separately that are switched from the RS-232C remote terminal.
No m
Yes k
The component signal and the
RGB signal cannot be used together.
The component signal cannot be used.
There is no limitation.
There is no limitation.
An RGB signal distributor is required.
Connecting to projector
For details on connecting the mixer to a projector, refer to the SRP-X500P Operating Instructions.
How to set the communication protocol
Set the communication protocol as follows.
1
Settings for the port
Set the BITS PER SECOND setup box and the
PARITY setup box in accordance with the specifications of the projector.
2
Settings for command to turn on the projector a Enter the command to turn on the projector connected to the mixer in the command input section of the PROTOCOL SETTING screen.
b Enter 60 seconds in the WAIT input box, then adjust the wait time during later operation check.
Note
If the commands that can be received by the projector are specified as ASCII code, convert the ASCII code to a hexadecimal number and enter it in the command input section.
3
Settings for command to set the projector to standby status a Enter the command to set the projector connected to the mixer to standby status in the command input section of the PROTOCOL SETTING screen.
b Enter 100 seconds in the WAIT input box, then adjust the wait time during later operation check.
4
Settings for command to define the input signal a Click one of the PROJECTOR INPUT SELECT buttons to specify the signal format, then enter the command in the command input section as follows:
When the projector input can be selected by sending a single command
Enter the input signal selection command to the
COMMAND 1 line. Leave the COMMAND 2 line blank.
When the signal format selection command and input terminal selection command are required
Enter the signal format selection command to the
COMMAND 1 line, then enter the input terminal selection command to the COMMAND 2 line.
Setting example
When the signal systems of VIDEO, COMPONENT and
RGB are used, and when a single command is required for the VIDEO input selection while both commands are required for the COMPONENT and RGB input signal selection, set as shown below.
Signal format COMMAND1
VIDEO VIDEO input terminal selection command
COMMAND2
Undefined (blank)
RGB RGB signal selection COMPONENT/RGB command input terminal select command
22
To Control the Projector Whose Protocol Is Not Preset to the Mixer
COMPONENT COMPONENT signal COMPONENT/RGB selection command input terminal select
OTHER
TERMINAL
Undefined (blank) command
Undefined (blank) b Enter 1 in the WAIT1 input box and enter 9 in the
WAIT2 input box, then adjust the wait time during later operation check.
5
Operation check by using the TEST button a Select VIDEO using the PROJECTOR INPUT
SELECT button without inputting any signals to
AV/RGB INPUT connectors of the mixer, then click the TEST button on the PROTOCOL
SETTING screen.
b Check that VIDEO is selected as the input signal on the projector.
c Do steps a and b for all other signal formats.
If the input selection on the projector is not performed correctly, check that the commands entered in the command input section and the port setting are correct.
After confirming the commands and the port setting, repeat the step 5 above by increasing the wait time to be input to the WAIT1 input box in 1-second steps until the projector operates correctly.
6
Operation check by using the AV/RGB
SELECT buttons on the mixer a Click one of the SIGNAL DEFINE selection radio buttons on the PARALLEL/PROJECTOR
CONTROL screen to make the setting for actual use.
b Input signals from all the AV/RGB INPUT connectors on the mixer, and press the AV/RGB
SELECT buttons on the mixer to check that the video signal is output to the projector.
c Press the AV/RGB SELECT buttons to check all operation patterns (A t B, A t C, A t D, A t E, ..... E t A, E t B, E t C, and E t D) to check that the video signal is output to the projector.
d Press the AV/RGB SELECT buttons several times at random to check that the video signal corresponding to the button which has been pressed the last is output to the projector.
e Repeat the step d more than ten times.
When the video signal is not output to the projector, check the settings of the SIGNAL DEFINE selection radio buttons on the PARALLEL/PROJECTOR
CONTROL screen and the settings on the projector.
After confirming the settings above are correct, do the steps below to adjust the wait time.
a Increase the wait time to be input to the WAIT1 and 2 input boxes at the same time in 1-second steps until the projector operates correctly.
b Decrease the wait time to be input to the WAIT1 input box in 1-second steps until the projector operates correctly.
c Decrease the wait time to be input to the WAIT2 input box in 1-second steps until the projector operates correctly.
If you want to shorten the time to take for the video signal is output to the projector after pressing the AV/
RGB SELECT buttons on the mixer, set the wait time for the WAIT1 and 2 input boxes to the shortest time first. Then perform “5 Operation check by using the
TEST button” and “6 Operation check by using the
AV/RGB SELECT buttons on the mixer”.
7
Operation check to turn on the projector a Press the AV/RGB SELECT A button on the mixer and check that the video signal is output to the projector.
b Operate the input signal selector on the projector so that no video signal is output to the projector.
c Press the POWER switch on the projector to place it to standby status.
d After confirming that the projector is in standby status, click the TEST button in the PROJECTOR
POWER ON section on the PROTOCOL
SETTING screen.
e Check that the projector turns on and the video signal output to the AV/RGB INPUT connector is input to the projector.
f Repeat the steps a to e for the AV/RGB
SELECT B-E buttons.
When the projector does not turn on, check that the command entered in the command input section is correct.
When the video signal is not output to the projector, repeat the test by increasing the wait time to be input to the WAIT input box in 1-second steps until the projector operates correctly.
If you want to shorten the time to take for the video signal is output after the projector turns on, repeat the test by decreasing the wait time to be input to the
WAIT input box in 1-second steps until the projector operates correctly.
8
Operation check to set the projector to standby status
To Control the Projector Whose Protocol Is Not Preset to the Mixer
23
a Click the TEST button in the PROJECTOR
POWER STANDBY section on the PROTOCOL
SETTING screen and check that the projector enters standby status.
b Click the TEST button in the PROJECTOR
POWER ON section and check that the projector turns on.
c Press the AV/RGB SELECT A button on the mixer and check that the video signal is output to the projector.
d Click the TEST button in the PROJECTOR
POWER STANDBY section, then after about 3 seconds, click the TEST button in the
PROJECTOR POWER ON section.
e Check that the projector enters standby status.
f Check that the projector turns on after the wait time specified by the WAIT input box elapses and the video signal output to the AV/RGB INPUT A connector is input to the projector.
When the projector does not enter standby status, check that the command entered in the command input section is correct.
When the projector does not turn on, repeat the test by increasing the wait time to be input to the WAIT input box in 1-second steps until the projector operates correctly.
24
To Control the Projector Whose Protocol Is Not Preset to the Mixer
Appendix
Factory settings (SYSTEM TYPE 0)
Inputs
Item
MIC INPUT1-4
LINE IN L,R
AV/RGB IN A-E
INDEX
MIC MIX BUS
FEED BACK REDUCER ON / OFF
FR / EQ
LCF
EQ1 FREQ
EQ2 FREQ
EQ3 FREQ
EQ4 FREQ
EQ5 FREQ
EQ1-5 Q
EQ1-5 GAIN
INPUT FADER
INPUT MUTING
INPUT FADER
INPUT MUTING
INPUT FADER
INPUT MUTING
SELECTOR
MIC 1 INPUT INDEX
MIC 2 INPUT INDEX
MIC 3 INPUT INDEX
MIC 4 INPUT INDEX
LINE INPUT INDEX
AV/RGB INPUT A INDEX
AV/RGB INPUT B INDEX
AV/RGB INPUT C INDEX
AV/RGB INPUT D INDEX
AV/RGB INPUT E INDEX
AGC ON / OFF
AGC COMPRESSOR THRESHOLD
AGC RATIO
AGC MAKE GAIN
AGC GATE THRESHOLD
AGC RANGE
AGC ATTACK
AGC HOLD TIME
AGC RELEASE
0dB
OFF
A
MIC 1
MIC 2
MIC 3
MIC 4
MD
DVD
VTR
CASSETTE
PC 1
PC 2
OFF
0dB
3:1
Factory setting
OFF
FR
ON
160Hz
450Hz
1.25kHz
3.55kHz
10kHz
1.2
0dB
0dB
OFF
0dB
OFF
0dB
– 30dB
– 20dB
22ms
10ms
100ms
Appendix
25
ROUTING ROUTING SPEAKER OUTPUT 1 MIC LEVEL
ROUTING SPEAKER OUTPUT 1 LINE L LEVEL
ROUTING SPEAKER OUTPUT 1 LINE R LEVEL
ROUTING SPEAKER OUTPUT 1 AV/RGB L LEVEL
ROUTING SPEAKER OUTPUT 1 AV/RGB R LEVEL
ROUTING SPEAKER OUTPUT 2 MIC LEVEL
ROUTING SPEAKER OUTPUT 2 LINE L LEVEL
ROUTING SPEAKER OUTPUT 2 LINE R LEVEL
ROUTING SPEAKER OUTPUT 2 AV/RGB L LEVEL
ROUTING SPEAKER OUTPUT 2 AV/RGB R LEVEL
ROUTING SPEAKER OUTPUT 3 MIC LEVEL
|
ROUTING LINE OUTPUT 4 AV/RGB R LEVEL
ROUTING SPEAKER OUTPUT 1 ROUTING ON / OFF
ROUTING SPEAKER OUTPUT 2 ROUTING ON / OFF
ROUTING SPEAKER OUTPUT 3 ROUTING ON / OFF
ROUTING SPEAKER OUTPUT 4 ROUTING ON / OFF
ROUTING LINE OUTPUT 1 ROUTING ON / OFF
ROUTING LINE OUTPUT 2 ROUTING ON / OFF
ROUTING LINE OUTPUT 3 ROUTING ON / OFF
ROUTING LINE OUTPUT 4 ROUTING ON / OFF
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB for all
ON : LINE IN L, AV/RGB IN L
ON : LINE IN R, AV/RGB IN R
ON : MIC MIX BUS
OFF for all
ON : MIC MIX BUS, LINE IN L, AV/
RGB IN L
ON : MIC MIX BUS, LINE IN R, AV/
RGB IN R
ON : MIC MIX BUS, AV/RGB IN L
ON : MIC MIX BUS, AV/RGB IN R
26
Appendix
Outputs
Item
SPEAKERS CH-1/2 OUTPUT FADER
OUTPUT MUTING
EQ BAND
EQ ON / OFF
EQ1 FREQ
EQ2 FREQ
EQ3 FREQ
EQ4 FREQ
EQ5 FREQ
EQ6 FREQ
EQ7 FREQ
EQ8 FREQ
EQ9 FREQ
EQ10 FREQ
EQ11 FREQ
EQ12 FREQ
EQ1-12 Q
EQ1-12 GAIN
COMPRESSOR ON / OFF
COMPRESSOR THRESHOLD
COMPRESSOR RATIO
COMPRESSOR ATTACK
COMPRESSOR RELEASE
DELAY ON/OFF
DELAY TIME
OUTPUT LINK ON / OFF
10dB
∞
: 1
0.47ms
100ms
OFF
0ms
ON
170Hz
315Hz
530Hz
950Hz
1.7kHz
2.97kHz
5kHz
9kHz
Factory setting
0dB
OFF
3 BAND
OFF
31.5Hz
50Hz
100Hz
16kHz
1.8
0dB
ON
Appendix
27
SPEAKERS CH-3/4 OUTPUT FADER
OUTPUT MUTING
EQ BAND
EQ ON / OFF
EQ1 FREQ
EQ2 FREQ
EQ3 FREQ
EQ4 FREQ
EQ5 FREQ
EQ6 FREQ
EQ7 FREQ
EQ8 FREQ
EQ9 FREQ
EQ10-12 FREQ
EQ1-12 Q
EQ1-12 GAIN
70V LINE
COMPRESSOR ON / OFF
COMPRESSOR THRESHOLD
COMPRESSOR RATIO
COMPRESSOR ATTACK
COMPRESSOR RELEASE
DELAY ON/OFF
DELAY TIME
OUTPUT LINK ON / OFF
70V LINE / Lo.imp
710Hz
1.5kHz
3.35kHz
7.5kHz
16kHz
20kHz
1.5
0dB
0dB
OFF
3 BAND
ON:CH-3 OFF:CH-4
31.5Hz
63Hz
150Hz
315Hz
ON:CH-3 OFF:CH-4
10dB
∞
: 1
0.47ms
100ms
OFF
0ms
OFF
70V LINE
28
Appendix
LINE OUTPUT 1/2 OUTPUT FADER
OUTPUT MUTING
EQ BAND
EQ ON / OFF
EQ1 FREQ
EQ2 FREQ
EQ3 FREQ
EQ4 FREQ
EQ5 FREQ
EQ6 FREQ
EQ7-12 FREQ
EQ1-6 Q
EQ7-12 Q
EQ1-12 GAIN
COMPRESSOR ON / OFF
COMPRESSOR THRESHOLD
COMPRESSOR RATIO
COMPRESSOR ATTACK
COMPRESSOR RELEASE
DELAY ON/OFF
DELAY TIME
OUTPUT LINK ON / OFF
LINE OUTPUT 3/4 OUTPUT FADER
OUTPUT MUTING
EQ BAND
EQ ON / OFF
EQ1 FREQ
EQ2 FREQ
EQ3 FREQ
EQ4-12 FREQ
EQ1 Q
EQ2 Q
EQ3 Q
EQ4-12 Q
EQ1-12 GAIN
COMPRESSOR ON / OFF
COMPRESSOR THRESHOLD
COMPRESSOR RATIO
COMPRESSOR ATTACK
COMPRESSOR RELEASE
DELAY ON/OFF
DELAY TIME
OUTPUT LINK ON / OFF
10dB
∞
: 1
0.47ms
100ms
OFF
0ms
ON
63Hz
2.5kHz
20kHz
20kHz
1
1.5
0.47
1.5
0dB
OFF
100ms
OFF
0ms
ON
0dB
OFF
0 BAND
OFF
0dB
OFF
0 BAND
OFF
31.5Hz
106Hz
375Hz
1.32kHz
4.5kHz
16kHz
20kHz
1
1.5
0dB
OFF
10dB
∞
: 1
0.47ms
Appendix
29
INDEX SPEAKER OUTPUT 1 INDEX
SPEAKER OUTPUT 2 INDEX
SPEAKER OUTPUT 3 INDEX
SPEAKER OUTPUT 4 INDEX
LINE OUTPUT 1 INDEX
LINE OUTPUT 2 INDEX
LINE OUTPUT 3 INDEX
LINE OUTPUT 4 INDEX
Remotes
Item
AV/RGB INPUT
REMOTE
PARALLEL
CH A VIDEO SIGNAL DEFINE
CH B VIDEO SIGNAL DEFINE
CH C VIDEO SIGNAL DEFINE
CH D VIDEO SIGNAL DEFINE
CH E VIDEO SIGNAL DEFINE
INPUT 1 FUNCTION
INPUT 2 FUNCTION
INPUT 3 FUNCTION
INPUT 4 FUNCTION
INPUT 5 FUNCTION
INPUT 6 FUNCTION
INPUT 7 FUNCTION
INPUT 8 FUNCTION
INPUT 9 FUNCTION
INPUT 10 FUNCTION
OUTPUT 1 FUNCTION
OUTPUT 2 FUNCTION
OUTPUT 3 FUNCTION
OUTPUT 4 FUNCTION
OUTPUT 5 FUNCTION
OUTPUT 6 FUNCTION
OUTPUT 7 FUNCTION
OUTPUT 8 FUNCTION
OUTPUT 9 FUNCTION
OUTPUT 10 FUNCTION
SP 1
SP 2
SP 3
SP 4
AUX L
AUX R
REC L
REC R
Factory setting
VIDEO
VIDEO
VIDEO
RGB
RGB
AV/RGB SELECT A
AV/RGB SELECT B
AV/RGB SELECT C
AV/RGB SELECT D
AV/RGB SELECT E
MASTER VOLUME UP
MASTER VOLUME DOWN
PROJECTOR POWER ON
PROJECTOR POWER STANDBY
EMG CLOSE
AV/RGB SELECT A
AV/RGB SELECT B
AV/RGB SELECT C
AV/RGB SELECT D
AV/RGB SELECT E
MASTER VOLUME MAX (UP)
MASTER VOLUME MIN (DOWN)
PROJECTOR POWER ON
PROJECTOR POWER STANDBY
EMG
30
Appendix
REMOTE FADER
ASSIGN
MASTER INPUT ASSIGN
MASTER SPEAKER OUTPUT ASSIGN
MASTER LINE OUTPUT ASSIGN
REMOTE 1-6 INPUT ASSIGN
REMOTE 1-6 SPEAKER OUTPUT ASSIGN
REMOTE 1-6 LINE OUTPUT ASSIGN
MASTER INDEX
REMOTE 1 INDEX
REMOTE 2 INDEX
REMOTE 3 INDEX
REMOTE 4 INDEX
REMOTE 5 INDEX
REMOTE 6 INDEX
POWER ON SETTING
PROJECTOR POWER
INFORMATION
Not assigned.
Assigned to SPEAKER OUT 1-4.
Assigned to LINE OUT 1/2.
Not assigned.
Not assigned.
Not assigned.
MASTER
REMOTE 1
REMOTE 2
REMOTE 3
REMOTE 4
REMOTE 5
REMOTE 6
LAST MEMORY
SYNC WITH POWER OFF only
Undefined.
Appendix
31
NOTICE FOR USERS
© 2004 Sony Corporation. All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to any machine readable from without prior written approval from Sony Corporation.
SONY CORPORATION PROVIDES NO WARRANTY
WITH REGARD TO THIS MANUAL, THE
SOFTWARE OR OTHER INFORMATION
CONTAINED HEREIN AND HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE WITH REGARD TO THIS
MANUAL, THE SOFTWARE OR SUCH OTHER
INFORMATION. IN NO EVENT SHALL SONY
CORPORATION BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES, WHETHER BASED ON TORT,
CONTRACT, OR OTHERWISE, ARISING OUT OF OR
IN CONNECTION WITH THIS MANUAL, THE
SOFTWARE OR OTHER INFORMATION
CONTAINED HEREIN OR THE USE THEREOF.
Sony Corporation reserves the right to make any modification to this manual or the information contained herein at any time without notice.
The software described herein may also be governed by the terms of a separate user license agreement.
Trademarks
• Celeron is a trademark of Intel Corporation (U.S.A. and other countries).
• Windows is a registered trademark of Microsoft
Corporation (U.S.A. and other countries).
• Adobe Acrobat and Adobe Reader are trademarks or registered trademarks of Adobe Systems Incorporated.
• Other system names, productions, and company names appearing in this manual are trademarks or registered trademarks of their respective holders. In this manual, such names are not indicated by ® or TM marks.
Sony Corporation
advertisement
Related manuals
advertisement