Sony STRDH130 User's Manual

filename[D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB01COV_STR-DH130-U2.fm]
masterpage:Right
4-294-472-11(1)
FM Stereo
FM/AM Receiver
Operating Instructions
STR-DH130
model name1[STR-DH130]
[4-294-472-11(1)]
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB02REG_STR-DH130U2.fm4-294-472-11(1)
masterpage: Left
For customers in the United
States
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the apparatus with
newspapers, tablecloths, curtains, etc. Do not place
the naked flame sources such as lighted candles on
the apparatus.
Owner’s Record
The model and serial numbers are located on the rear
of the unit. Record these numbers in the space
provided below. Refer to them whenever you call
upon your Sony dealer regarding this product.
Model No.
Serial No.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing, and
do not place objects filled with liquids, such as
vases, on the apparatus.
As the main plug is used to disconnect the unit from
the mains, connect the unit to an easily accessible
AC outlet. Should you notice an abnormality in the
unit, disconnect the main plug from the AC outlet
immediately.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or
the like.
Important Safety Instructions
The unit is not disconnected from the mains as long
as it is connected to the AC outlet, even if the unit
itself has been turned off.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
This symbol is intended to alert
the user to the presence of the Hot
Surface that may be hot if it is
touched during the normal
operation.
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10)Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11)Only use attachments/accessories specified by
the manufacturer.
2GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB02REG_STR-DH130U2.fm
12)Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or
when unused for long periods of time.
14)Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
masterpage: Right
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
To reduce the risk of electric shock, the speaker cord
should be connected to the apparatus and the
speakers in accordance with the following
instructions.
1) Disconnect the AC power cord from the MAINS.
2) Strip 10 to 15 mm of the wire insulation of the
speaker cord.
3) Connect the speaker cord to the apparatus and
the speakers carefully so as not to touch the core
of speaker cord by hand. Also disconnect the AC
power cord from the MAINS before
disconnecting the speaker cord from the
apparatus and the speakers.
The following FCC statement
applies only to the version of
this model manufactured for
sale in the U.S.A. Other
versions may not comply with
FCC technical regulations.
For customers in Europe
NOTE:
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. The recycling of materials
will help to conserve natural resources. For more
detailed information about recycling of this product,
please contact your local Civic Office, your
household waste disposal service or the shop where
you purchased the product.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
continued
3GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB02REG_STR-DH130U2.fm4-294-472-11(1)
Disposal of waste batteries
(applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the battery or on the packaging
indicates that the battery provided with this product
shall not be treated as household waste.
On certain batteries this symbol might be used in
combination with a chemical symbol. The chemical
symbols for mercury (Hg) or lead (Pb) are added if
the battery contains more than 0.0005% mercury or
0.004% lead.
By ensuring these batteries are disposed of correctly,
you will help prevent potentially negative
consequences for the environment and human health
which could otherwise be caused by inappropriate
waste handling of the battery. The recycling of the
materials will help to conserve natural resources.
In case of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery, this battery
should be replaced by qualified service staff only.
To ensure that the battery will be treated properly,
hand over the product at end-of-life to the applicable
collection point for the recycling of electrical and
electronic equipment.
For all other batteries, please view the section on
how to remove the battery from the product safely.
Hand the battery over to the applicable collection
point for the recycling of waste batteries.
For more detailed information about recycling of
this product or battery, please contact your local
Civic Office, your household waste disposal service
or the shop where you purchased the product.
masterpage: Left
About This Manual
• The instructions in this manual are for model
STR-DH130. The model number is located at the
lower right corner of the front panel. The
illustrations used in this manual are of Europe
model and they may be different from your model.
Any differences in operation are marked in the
manual as “Europe model only”.
• The instructions in this manual describe the
operation of the receiver with the supplied remote
control. You can also use the buttons or knobs on
the receiver if they have the same or similar names
as those on the remote control.
Notice for customers: The following
information is only applicable to
equipment sold in countries applying
EU Directives.
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo,
108-0075 Japan. The Authorized Representative for
EMC and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters
please refer to the addresses given in separate
service or guarantee documents.
4GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB01COV_STR-DH130U2TOC.fm
masterpage: Right
Table of Contents
About This Manual........................................4
Supplied accessories......................................6
Description and location of parts...................7
Getting started .............................................13
Connections
Additional Information
Precautions.................................................. 29
Troubleshooting .......................................... 30
Specifications.............................................. 32
Index ........................................................... 34
1: Installing the speakers .............................13
2: Connecting the speakers ..........................14
3: Connecting the audio/video equipment...14
4: Connecting the antennas (aerials)............17
5: Connecting the AC power cord
(mains lead) ............................................18
Preparing the Receiver
Initializing the receiver ................................18
Selecting the speaker system .......................19
Adjusting the tone........................................19
Basic Operations
Playback ......................................................20
Viewing information on the display
panel .......................................................21
Recording using the receiver .......................22
Tuner Operations
Listening to FM/AM radio ..........................22
Presetting FM/AM radio stations
(Preset Tuning) .......................................24
Receiving RDS broadcasts ..........................26
(Europe model only)
Menu Operations
Using the setting menu ................................26
Using the Remote Control
Reassigning the input button .......................27
Resetting the input buttons ..........................28
5GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB01COV_STR-DH130U2TOC.fm
Supplied accessories
• Operating Instructions (this manual)
• Quick Setup Guide
• FM wire antenna (aerial) (1)
masterpage: Left
Inserting batteries into the
remote control
Insert two R6 (size AA) batteries (supplied) by
matching 3 and # on the batteries to the
diagram inside the battery compartment of the
remote control.
• AM loop antenna (aerial) (1)
• Remote control (RM-AAU130) (1)
Notes
• R6 (size AA) batteries (2)
• Do not leave the remote control in an extremely hot
or humid place.
• Do not use a new battery with old ones.
• Do not mix manganese batteries and other kinds of
batteries.
• Do not expose the remote control sensor to direct
sunlight or lighting apparatuses. Doing so may
cause a malfunction.
• If you do not intend to use the remote control for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace or remove the batteries, the
remote control buttons may be reset to their default
settings. If this happens, reassign the input buttons
(page 27).
• When the receiver no longer responds to the
remote control, replace all the batteries with new
ones.
6GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB03DES_STR-DH130U2.fm
masterpage: Right
Description and location of parts
Front panel
1
qd
2 3
qs
4
qa
5
0
6
9
8
7
Indicators on the display panel
qg
qf
SP A
SP B
MEMORY
RDS
MONO SLEEP
ST
qh
B SPEAKERS (OFF/A/B/A+B) (page 14, 19)
H DIMMER
Adjusts the brightness of the display panel in 3
levels.
C INPUT SELECTOR (page 20, 22 - 25)
I DISPLAY (page 21)
D Display panel
J BASS +/–, TREBLE +/– (page 19)
E Remote control sensor
Receives signals from remote control.
K TUNING MODE, TUNING +/–, MEMORY/
ENTER (page 23, 25)
F MASTER VOLUME (page 20)
L FM MODE (page 23)
G MUTING (page 20)
M PHONES jack (page 30)
A ?/1 (on/standby) (page 18, 24)
continued
7GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB03DES_STR-DH130U2.fm
masterpage: Left
N SP A/SP B
Lights up according to the speaker system used
(page 19). However, these indicators do not light
up if the speaker output is turned off or if
headphones are connected.
O SLEEP
Lights up when the Sleep Timer is activated
(page 11).
P Tuning indicators
Lights up when the receiver tunes to a radio
station.
MEMORY
A memory function, such as Preset Memory
(page 24), etc., is activated.
RDS (Europe model only)
Tuned to a station with RDS services.
MONO
Monaural broadcast
ST
Stereo broadcast
Preset station number (The number will change
according to the preset station you select.)
8GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB03DES_STR-DH130U2.fm
masterpage: Right
Rear panel
1
2
3
A Audio signal section (page 14, 16)
White (L)
AUDIO IN/OUT jacks
Red (R)
PORTABLE IN jack
B ANTENNA section (page 17)
FM ANTENNA jack
AM ANTENNA terminals
C SPEAKERS section (page 14)
9GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB03DES_STR-DH130U2.fm
To control the receiver
Remote control
Use the supplied remote control to operate this
receiver and other equipment. The remote
control is assigned to operate Sony audio/
video equipment. You can reassign the input
button to match the equipment connected to
your receiver (page 27).
RM-AAU130
wd
1
ws
2
3
wa
4
5
w;
6
ql
7
8
9
0
qa
qk
masterpage: Left
qj
qs
qh
qd
B ?/1* (on/standby)
Turns the receiver on or sets it to standby mode.
C Input buttons
Selects the equipment you want to use. When
you press any of the input buttons, the receiver
turns on. The buttons are assigned to control
Sony equipment.
G D.TUNING
Enters direct tuning mode.
H ENTER/MEMORY
Stores a station during tuner operation.
I AMP MENU
Displays the menu to operate the receiver.
K MUTING
Turns off the sound temporarily.
Press the button again to restore the sound.
L MASTER VOL +**/–
Adjust the volume level of all speakers at the
same time.
N TUNING +/–
Scans a station.
PRESET +/–
Selects preset stations.
FM MODE
Selects the FM monaural or stereo reception.
P RETURN/EXIT O
Returns to the previous menu.
Q
, V/v/B/b
Press V/v/B/b to select the settings, then press
to enter/confirm the selection.
R DISPLAY
Views information on the display panel.
qf
T Numeric buttons**
Presets or tune to the preset stations.
qg
10GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB03DES_STR-DH130U2.fm
V SLEEP
Sets the receiver to turn off automatically at a
specified time.
Each time you press this button, the display
changes cyclically as follows.
0-30-00 t 1-00-00 t 1-30-00 t 2-00-00 t
OFF
When Sleep Timer is being used, “SLEEP”
indicator lights up in the display panel.
Tip
To check the remaining time before the receiver
turns off, press SLEEP. The remaining time
appears on the display panel. If you press
SLEEP again, the Sleep Timer will be canceled.
* If you press AV ?/1 (A) and ?/1 (B)
simultaneously, the receiver and connected
equipment will turn off (SYSTEM STANDBY).
The function of the AV ?/1 (A) changes
automatically each time you press the input
buttons (C).
**The number 5, MASTER VOL +/TV VOL +, and
N buttons have tactile dots. Use the tactile dots
as references when operating the receiver.
To control a Sony TV
Hold down TV (O), then press the button
printed in orange to select the function you
want.
Example: Hold down TV (O), then press
TV CH +.
1
Hold
down
TV
masterpage: Right
K MUTING
Activates the TV’s muting function.
L TV VOL +**/–
Adjusts the TV volume.
M MENU/HOME
Displays the TV menus.
N TV CH +/–
Scans for the preset TV channels.
P RETURN/EXIT O
Returns to the previous TV menu.
R DISPLAY
Displays information related to the current TV
program.
S -/-Selects TV channel entry mode.
>10/
Selects the channel numbers of the Digital
CATV terminal.
For example, to select 2.1, press 2, >10/ and 1.
x
x
T Numeric buttons**
Selects the TV channels.
W TV INPUT
Selects the input signal.
* If you press AV ?/1 (A) and ?/1 (B)
simultaneously, the receiver and connected
equipment will turn off (SYSTEM STANDBY).
The function of the AV ?/1 (A) changes
automatically each time you press the input
buttons (C).
**The number 5, MASTER VOL +/TV VOL +, and
N buttons have tactile dots. Use the tactile dots
as references when operating the receiver.
2
Press
TV CH +
A TV ?/1 (on/standby)
Turns the TV on or off.
H ENTER/MEMORY
Enters the selections.
J TOOLS/OPTIONS
Displays the TV function options.
continued
11GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB03DES_STR-DH130U2.fm
masterpage: Left
To control other Sony equipment
Name
Blu-ray Disc,
DVD player
Satellite tuner, VCR
Cable TV
tuner
CD player
MD deck,
Tape deck
Power
Power
Powerc)
A
AV ?/1a)
Power
Power
E
POP UP/MENU
Menu
–
–
–
–
F
TOP MENU
On-screen
guide
–
–
–
–
H
ENTER/MEMORY
Enter
Enter
Enter
Enter
–
J
TOOLS/OPTIONS
Options menu
Options menu
–
–
–
M
MENU/HOME
Menu
Menu
Menu
–
–
N
./>
Skip track
Select channel Search index
Skip track
Skip track
REPLAY
/
ADVANCE
Replay,
fast forward
–
Replay,
fast forward
–
–
m/M
Search forward, –
backward
Fast forward,
rewind
Fast forward,
rewind
Fast forward,
rewind
Nb)
Play
–
Play
Play
Play
X
Pause
–
Pause
Pause
Pause
x
Stop
–
Stop
Stop
Stop
RETURN/EXIT O
Return
Return, exit
–
–
–
Enter
Enter
Enter
Enter
Enterc)
P
Q
V/v/B/b
Select
Select
Select
–
–
R
DISPLAY
Display
Display
Display
Display
Displayc)
S
-/--
–
–
–
–
–
>10/
–
(.)dotd)
Track > 10
Track > 10
–
CLEAR
Clear
Clear
–
–
–
Numeric buttonsb)
Track
Channel
Channel
Track
Trackc)
x
T
a) If
you press AV ?/1 (A) and ?/1 (B)
simultaneously, the receiver and connected
equipment will turn off (SYSTEM STANDBY).
The function of the AV ?/1 (A) changes
automatically each time you press the input
buttons (C).
b)
The number 5, MASTER VOL +/TV VOL +, and
N buttons have tactile dots. Use the tactile dots as
references when operating the receiver.
c)
For MD deck only.
d) For example, to select 2.1, press 2, >10/ and 1.
x
Notes
• The above explanation is intended to serve as
examples.
• Depending on the model of your connected
equipment, some functions explained in this
section may not work with the supplied remote
control.
12GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB04CON_STR-DH130U2.fm
Getting started
Installing and connecting the
speakers (page 13, 14)
Connecting the audio/video
equipment (page 14, 16)
Connections
1: Installing the speakers
This receiver allows you to use a 2.0 channel
system.
Example of speaker system
configuration
Left
speaker
Right
speaker
Preparing the receiver
See “5: Connecting the AC power cord (mains
lead)” (page 18) and “Initializing the receiver”
(page 18).
Selecting the speaker system
(page 19)
13GB
STR-DH130
4-294-472-11(1)
Connections
You can enjoy your audio/video equipment
connected to the receiver by following the
simple steps below.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB04CON_STR-DH130U2.fm
2: Connecting the
speakers
masterpage: Left
3: Connecting the audio/
video equipment
Before connecting the cords, be sure to
disconnect the AC power cord (mains lead).
Connecting the audio equipment
Before connecting cords, be sure to disconnect
the AC power cord (mains lead).
Left speaker
Super Audio
CD player,
CD player
A
A
SPEAKERS B
terminals*
A
1
10 mm
(13/32")
2
Right speaker
4
B
3
A
A Speaker cords (not supplied)
* If you have an additional speaker system, connect
them to the SPEAKERS B terminals. You can
select the speakers you want to use with the
SPEAKERS (OFF/A/B/A+B) button on the
receiver (page 19).
Portable
audio
MD deck,
Tape deck
A Audio cord (not supplied)
B Phono cord with stereo headphone
jack (not supplied)
* If you want to record, you must make this
connection (page 22).
14GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB04CON_STR-DH130U2.fm
masterpage: Right
Notes
Connections
• When listening to a equipment connected to the
PORTABLE IN jack, sound may be distorted or
interrupted. This is not a malfunction and will
depend on the connected equipment.
• If the sound from the equipment connected to the
PORTABLE IN jack is very soft, you may increase
the volume level. However, before you switch to
other input, be sure to reduce the volume level to
avoid damaging your speaker.
15GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB04CON_STR-DH130U2.fm
masterpage: Left
Connecting the video equipment
Before connecting cords, be sure to disconnect the AC power cord (mains lead).
Blu-ray Disc player,
DVD player
Video
signals
Audio signals
To the VIDEO IN
jack of the TV.
A
A
To the VIDEO IN
jack of the TV.
Video
signals
Audio
signals
Satellite tuner,
Cable TV tuner
A
To the VIDEO IN
jack of the TV.
Video
signals
Audio
signals
VCR,
DVD recorder
A Audio cord (not supplied)
* If you want to record, you must make this
connection (page 22).
16GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB04CON_STR-DH130U2.fm
masterpage: Right
Notes
4: Connecting the
antennas (aerials)
Before connecting antennas (aerials), be sure
to disconnect the AC power cord (mains lead).
FM wire antenna (aerial)
(supplied)
AM loop antenna (aerial)
(supplied)
Notes
• To prevent noise pickup, keep the AM loop
antenna (aerial) away from the receiver and other
equipment.
• Be sure to fully extend the FM wire antenna
(aerial).
• After connecting the FM wire antenna (aerial),
keep it as horizontal as possible.
17GB
STR-DH130
4-294-472-11(1)
Connections
• The default setting for the BD/DVD and VIDEO
input buttons on the remote control is as follows:
BD/DVD: Blu-ray Disc player
VIDEO: VCR
Be sure to change the default setting of the
BD/DVD (and VIDEO) input button so that you
can use the button to control your DVD player (and
DVD recorder). For details, see “Reassigning the
input button” (page 27).
• You can also rename the BD/DVD and VIDEO
input so that it can be displayed on the receiver’s
display panel. For details, see “Naming inputs”
(page 20).
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB04CON_STR-DH130U2.fm
5: Connecting the AC
power cord (mains lead)
Connect the AC power cord (mains lead) to a
wall outlet.
AC power cord (mains lead)
masterpage: Left
Preparing the Receiver
Initializing the receiver
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to revert back to the factory default
settings.
Be sure to use the buttons on the receiver to
perform this operation.
?/1
To the wall outlet
1
Press ?/1 to turn off the
receiver.
2
Hold down ?/1 for 5 seconds.
The “CLEARING” appears on the
display panel for a while, then changes to
“CLEARED”.
Changes or adjustments made to the
settings are now reset to the defaults.
18GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB04CON_STR-DH130U2.fm
Selecting the speaker
system
Adjusting the tone
You can adjust the tonal quality of the
speakers.
BASS
+/–
TREBLE
+/–
SPEAKERS (OFF/A/B/A+B)
Press SPEAKERS (OFF/A/B/A+B)
repeatedly to select the speaker
system you want to drive.
To select
Light up
The speakers connected to the
SPEAKERS A terminals
SP A
The speakers connected to the
SPEAKERS B terminals
SP B
The speakers connected to both the
SPEAKERS A and B terminals
(parallel connection)
SP A
SP B
Press TREBLE + or TREBLE –
repeatedly to adjust the treble
level.
Press BASS + or BASS –
repeatedly to adjust the bass level.
You can adjust from –10 dB to +10 dB in 1 dB
step.
The initial setting is 0 dB.
To turn off the speaker output
Press SPEAKERS (OFF/A/B/A+B)
repeatedly until the “SP A” and “SP B”
indicators on the display do not light up.
Note
You cannot switch the speaker system by pressing
SPEAKERS (OFF/A/B/A+B) when the headphones
are connected.
19GB
STR-DH130
4-294-472-11(1)
Preparing the Receiver
You can select the speakers you want to drive,
if you have connected the speakers to
SPEAKERS A and B terminals.
Be sure to use the buttons on the receiver to
perform this operation.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB05BAS_STR-DH130U2.fm
masterpage: Left
To activate the muting function
Press MUTING.
The muting function will be canceled when
you do the following.
• Press the button again.
• Increase the volume.
• Turn off the receiver.
Basic Operations
Playback
Input
buttons
To avoid damaging your
speakers
Before you turn off the receiver, be sure to turn
down the volume level.
AMP
MENU
MUTING
,
V/v/B/b
1
Turn on the connected
equipment.
2
3
Turn on the receiver.
MASTER
VOL +/–
Press the input button which
corresponds to the equipment
you want.
You can also use INPUT SELECTOR on
the receiver.
The selected input appears on the display
panel.
You can enter a name of up to 8 characters for
inputs (except TUNER) to appear on the
display panel.
It is more recognizable having the equipment
named on the display than the jacks.
1
Press the corresponding input
button which you want to
create an index name.
You can also use INPUT SELECTOR on
the receiver.
2
3
Press AMP MENU.
Press V/v repeatedly to select
“NAME IN”, then press
or b.
The cursor flashes and you can enter a
character.
4
When you press TUNER, “FM TUNER” or
“AM TUNER” appears for a while, and then
frequency appears on the display panel.
Press V/v to select a character,
then press B/b to move the
input position backward and
forward.
Play back the source.
Tips
Note
4
5
Naming inputs
Press MASTER VOL +/– to
adjust the volume.
You can also use MASTER VOLUME on
the receiver.
• You can select the character type as follows
by pressing V/v.
Alphabet (upper case) t Numbers t
Symbols
• To enter a blank space, press b without
selecting a character.
20GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB05BAS_STR-DH130U2.fm
If you made a mistake
Press B/b until the character you want to
change flashes, then press V/v to select
the correct character.
5
Press
.
The name you entered is registered.
When receiving RDS broadcasts
(Europe model only)
Program Service name or preset station
name* t Frequency, band and preset
number t Volume level
* Index name appears only when you have
assigned one to the input or preset station
(page 20, 25). Index name does not appear
when only blank spaces have been entered,
or it is the same as the input name.
Note
Character or marks may not be displayed for some
languages.
Input
buttons
AMP
MENU
DISPLAY
1
Press the corresponding input
button which you want to check
the information.
2
Press AMP MENU, then press
DISPLAY repeatedly.
Each time you press the button, the
display changes cyclically as follows:
Index name of the input* t Selected
input t Volume level
When listening to FM and AM radio
Preset station name* t Frequency, band
and preset number t Volume level
21GB
STR-DH130
4-294-472-11(1)
Basic Operations
Viewing information on
the display panel
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB05BAS_STR-DH130U2.fm
Recording using the
receiver
You can record sound from an audio/video
equipment using the receiver. Refer to the
operating instructions supplied with your
recording equipment.
1
Press the input button which
corresponds to the playback
equipment.
You can also use INPUT SELECTOR on
the receiver.
2
Prepare the playback
equipment for playing.
For example, insert the CD you want to
copy into the CD player.
3
4
Tuner Operations
Listening to FM/AM radio
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and
AM antennas (aerials) to the receiver (page
17).
Tip
The tuning scale for direct tuning is shown below.
Area
FM
AM
USA, Canada
100 kHz
10 kHz*
Europe
50 kHz
9 kHz
* The AM tuning scale can be changed (page 24).
TUNER
Prepare the recording
equipment.
Insert a blank MD, tape or video tape into
the recording equipment (connected to
MD/TAPE AUDIO OUT or VIDEO
AUDIO OUT jacks).
Start recording on the
recording equipment, then start
the playback equipment.
masterpage: Left
Numeric
buttons
D.TUNING
,
V/v/B/b
Notes
• Some sources contain copyright protection to
prevent recording. In this case, you may not be able
to record from the source.
• Sound adjustments do not affect the signal output
from the MD/TAPE AUDIO OUT or VIDEO
AUDIO OUT jacks.
• While the source is being recorded, the auto
standby function of the receiver may start up and
interrupt the recording. In this case, set the
“AUTO.STBY” to “STBY OFF” (page 27).
• You can record the sound from the video
equipment connected to this receiver. However,
you cannot record the image via this receiver.
TUNING
+/–
FM
MODE
22GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB05BAS_STR-DH130U2.fm
Tuning to a station
automatically (Automatic
Tuning)
1
2
Press TUNER repeatedly to
select the FM or AM band.
Tuning to a station directly
(Direct Tuning)
You can enter the frequency of a station
directly by using the numeric buttons.
1
Press TUNING + or TUNING –.
TUNING + scans from lower to higher
frequency stations and TUNING – for
scanning higher to lower.
The receiver stops scanning whenever a
station is received.
masterpage: Right
Press TUNER repeatedly to
select the FM or AM band.
You can also use INPUT SELECTOR on
the receiver.
2
3
Press D.TUNING.
Example 1: FM 102.50 MHz
• USA and Canada models only:
Select 1 b 0 b 2 b 5
• Other models:
Select 1 b 0 b 2 b 5 b 0
Example 2: AM 1,350 kHz
Select 1 b 3 b 5 b 0
Using the control buttons on
the receiver
1 Turn INPUT SELECTOR to select the FM
or AM band.
2 Press TUNING MODE repeatedly to select
“AUTO”.
3 Press TUNING + or TUNING –.
Tip
Adjust the direction of the AM loop antenna
(aerial) for optimum reception upon tuning to
an AM station.
In case of poor FM stereo
reception
If the FM stereo reception is poor and “ST”
flashes on the display panel, select monaural
audio to lessen the sound distortion.
Press FM MODE repeatedly until the
“MONO” indicator lights up on the display
panel.
To return to the stereo mode, press FM MODE
repeatedly until the “MONO” indicator on the
display panel does not light up.
4
Press
.
If you cannot tune to a station
“- - - .- - MHz” or “- - - - kHz” appears and then
the screen returns to the current frequency.
Make sure you have entered the right
frequency. Try repeating steps 2 to 4. If you
still cannot tune to a station, the frequency
may not be in use in your area.
23GB
STR-DH130
4-294-472-11(1)
Tuner Operations
Press the numeric buttons to
enter the frequency.
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB05BAS_STR-DH130U2.fm
Changing the AM tuning scale
masterpage: Left
(USA and Canada models only)
Presetting FM/AM radio
stations
You can change the AM tuning scale to either
9 kHz or 10 kHz using the buttons on the
receiver.
(Preset Tuning)
?/1
You can store up to 30 FM and 30 AM stations
as your favorite stations as preset stations.
TUNER
TUNING MODE
1
Press ?/1 to turn off the
receiver.
2
While holding down TUNING
MODE, press ?/1.
3
Change the current AM tuning
scale to 9 kHz (or 10 kHz).
Numeric
buttons
ENTER/
MEMORY
AMP
MENU
,
V/v/B/b
PRESET
+/–
To reset the scale to 10 kHz (or 9 kHz),
repeat the procedure above.
Note
All preset stations will be erased when you change
the tuning scale.
1
Press TUNER repeatedly to
select the FM or AM band.
You can also use INPUT SELECTOR on
the receiver.
2
Tune to the station that you
want to preset using Automatic
Tuning (page 23) or Direct
Tuning (page 23).
3
Press ENTER/MEMORY.
You can also use MEMORY/ENTER on
the receiver.
4
Press the numeric buttons to
select a preset number.
You can also press PRESET + or
PRESET – to select a preset number.
24GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB05BAS_STR-DH130U2.fm
5
Press
Naming preset stations
.
The station is stored as the selected preset
number.
6
Press TUNER repeatedly to
select the FM or AM band.
You can also use INPUT SELECTOR on
the receiver.
2
Tune to the preset station you
want to create an index name
for (page 25).
3
4
Press AMP MENU.
1
2
3
4
5
30
29
28
...
Press V/v repeatedly to select
“NAME IN”, then press
or b.
The cursor flashes and you can enter a
character.
Press PRESET + or PRESET –
repeatedly to select the station.
Each time you press the button, you can
select a preset station as follows:
Press TUNER repeatedly to
select the FM or AM band.
5
27
Press V/v to select a character,
then press B/b to move the
input position backward and
forward.
You can enter up to 8 characters to name
the station.
You can also press the numeric buttons to
enter the preset station. To tune to the
selection, press .
Tips
• You can select the character type as follows
by pressing V/v.
Alphabet (upper case) t Numbers t
Symbols
• To enter a blank space, press b without
selecting a character.
Using the control buttons on
the receiver
1 Turn INPUT SELECTOR to select the FM
or AM band.
If you made a mistake
Press B/b until the character you want to
change flashes, then press V/v to select
the correct character.
2 Press TUNING MODE repeatedly to select
“PRESET”.
3 Press TUNING + or TUNING – to select the
preset station you want.
6
Press
.
The name you entered is registered.
Note (Europe model only)
When you name an RDS (Radio Data System)
station and tune to that station, the Program Service
name appears instead of the name you entered.
25GB
STR-DH130
4-294-472-11(1)
Tuner Operations
You can also use INPUT SELECTOR on
the receiver.
2
1
Repeat steps 1 to 5 to store
another station.
Tuning to preset stations
1
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB06REM_STR-DH130U2.fm
Receiving RDS
broadcasts
masterpage: Left
Menu Operations
Using the setting menu
(Europe model only)
This receiver allows you to use Radio Data
System (RDS), which enables radio stations to
send additional information along with the
regular programming signal. This receiver
offers convenient RDS features, such as
Program Service name display. RDS is
available only for FM stations.*
* Not all FM stations provide RDS service, nor do
they provide the same type of services. If you are
not familiar with the RDS services in your area,
check with your local radio stations for details.
Simply select a station on the FM
band using Direct Tuning (page 23),
Automatic Tuning (page 23), or
Tuning with Preset Station
(page 25).
When you tune to a station that provides RDS
services, “RDS” lights up and the Program
Service name appears on the display panel.
Note
RDS may not work properly if the station you tuned
to is not transmitting the RDS signal or if the signal
strength is weak.
You can customize the receiver by making
various adjustments with setting menu.
AMP
MENU
,
V/v/B/b
RETURN/
EXIT O
1
2
3
Press AMP MENU.
Press V/v repeatedly to select
the menu item you want, then
press
or b.
Press V/v repeatedly to select
the setting you want, then
press
.
To return to the previous
display
Press B or RETURN/EXIT O.
Tip
To exit the menu
While a Program Service name is displayed, you can
check the frequency by pressing DISPLAY
repeatedly (page 21).
Press AMP MENU.
Note
Some parameters and settings may appear dimmed
on the display panel. This means that they are either
unavailable or fixed and unchangeable.
26GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB06REM_STR-DH130U2.fm
Overview of the menus
masterpage: Right
Using the Remote Control
x BALANCE (Speaker balance)
Lets you adjust the balance between left and
right speakers.
You can adjust from BAL. L+10 to
BAL. R+10 in 1dB/step.
The initial setting is BAL. 0.
x NAME IN (Naming)
Lets you set the name of inputs and preset
stations. For details, see “Naming inputs”
(page 20) and “Naming preset stations”
(page 25).
x AUTO.STBY (Auto Standby)
Notes
• This function does not work when TUNER input is
selected.
• If you use the Auto standby mode and the Sleep
Timer at the same time, the Sleep Timer has
priority.
You can change the default settings of the
input buttons to suit the equipment in your
system. For example, if you connect a Blu-ray
Disc player to the SAT jack on the receiver,
you can set the SAT button on this remote
control to control the Blu-ray Disc player.
Note
You cannot reassign the TUNER and PORTABLE
input buttons.
1
Hold down the input button of
which you want to change the
assignment.
Example: Hold down SAT.
2
Referring to the table below,
press the corresponding
button for the category you
want.
Example: Press 8.
Now you can use the SAT button to
control the Blu-ray Disc player.
continued
27GB
STR-DH130
4-294-472-11(1)
Menu Operations/Using the Remote Control
Lets you set the receiver switch to standby
mode automatically when you do not operate
the receiver or when there is no signals input to
the receiver.
• STBY ON
Switches to standby mode after
approximately 30 minutes.
• STBY OFF
Does not switch to standby mode.
Reassigning the input
button
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB06REM_STR-DH130U2.fm
Categories and the
corresponding buttons
Categories
Press
VCR (command mode
VTR 3)a)
1
DVD player
(command mode DVD1)
2
DVD recorder
(command mode DVD3)b)
3
CD player
4
Euro Digital Satellite
Receiver
5
DVR (Digital CATV
terminal)
6
DSS (Digital Satellite
Receiver)
7
Blu-ray Disc player
(command mode BD1)c)
8
Blu-ray Disc recorder
(command mode BD3)c)
9
MD deck
0/10
Tape deck
-/--
a) Sony
VCRs are operated with a VTR 3
setting which corresponds to VHS.
b) Sony DVD recorders are operated with a
DVD1 or DVD3 setting. For details, refer to
the operating instructions supplied with the
DVD recorders.
c) For details on the BD1 or BD3 setting, refer
to the operating instructions supplied with
the Blu-ray Disc player or Blu-ray Disc
recorder.
masterpage: Left
Resetting the input
buttons
TV
INPUT
?/1
MASTER
VOL –
1
While holding down MASTER
VOL –, press ?/1 and TV INPUT.
2
Release all buttons.
The input buttons are reset to the default
setting.
28GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB06REM_STR-DH130U2.fm
masterpage: Right
On placement
Additional Information
Precautions
On safety
Should any solid object or liquid fall into the
cabinet, unplug the receiver and have it
checked by qualified personnel before
operating it any further.
On power sources
On heat buildup
On operation
Before connecting other equipment, be sure to
turn off and unplug the receiver.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.
If you have any questions or problems
concerning your receiver, please consult your
nearest Sony dealer.
Although the receiver heats up during
operation, this is not a malfunction. If you
continuously use this receiver at a large
volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid
burning yourself, do not touch the cabinet.
29GB
STR-DH130
4-294-472-11(1)
Additional Information
• Before operating the receiver, check that the
operating voltage is identical with your local
power supply.
The operating voltage is indicated on the
nameplate on the back of the receiver.
• The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
• If you are not going to use the receiver for a
long time, be sure to disconnect the receiver
from the wall outlet. To disconnect the AC
power cord (mains lead), grasp the plug
itself; never pull the cord.
• The AC power cord (mains lead) must be
changed only at a qualified service shop.
• (USA and Canada models only)
One blade of the plug is wider than the other
for the purpose of safety and will fit into the
wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact
your dealer.
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and
prolong the life of the receiver.
• Do not place the receiver near heat sources,
or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
• Do not place anything on top of the cabinet
that might block the ventilation holes and
cause malfunctions.
• Do not place the receiver near equipment
such as a TV, VCR, or tape deck. (If the
receiver is being used in combination with a
TV, VCR, or tape deck, and is placed too
close to that equipment, noise may result,
and picture quality may suffer. This is
especially likely when using an indoor
antenna (aerial). Therefore, we recommend
using an outdoor antenna (aerial).)
• Use caution when placing the receiver on
surfaces that have been specially treated
(with wax, oil, polish, etc.) as staining or
discoloration of the surface may result.
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB06REM_STR-DH130U2.fm
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem. Should any problem persist, consult
your nearest Sony dealer. Note that if service
personnel changes some parts during repair,
these parts may be retained.
Power
The receiver is turned off
automatically.
• “AUTO.STBY” is set to “STBY ON”
(page 27).
• The Sleep Timer function is working
(page 11).
Sound
There is no sound from one of the
speakers.
• Connect a pair of headphones to the
PHONES jack to verify that sound is
output from the headphones. If only one
channel is output from the headphones, the
equipment may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the equipment. If both
channels are output from the headphones,
the speaker may not be connected to the
receiver correctly. Check the connection of
the speaker which is not outputting any
sound.
• Make sure you have connected to both the
L and R jacks of an analog equipment,
analog equipment requires both L and R
jack connections. Use an audio cord (not
supplied).
masterpage: Left
There is no sound from a specific
equipment.
• Check that the equipment is connected
correctly to the audio input jacks for that
equipment.
• Check that the cord(s) used for the
connection is (are) fully inserted into the
jacks on both the receiver and the
equipment.
There is no sound, no matter which
equipment is selected, or only a very
low-level sound is heard.
• Check that all connecting cords are
inserted to their input/output jacks for the
respective jacks of the receiver, speakers
and the equipment.
• Check that both the receiver and all
equipment are turned on.
• Check that MASTER VOLUME is not set
to “VOL MIN”.
• Check that the SPEAKERS (OFF/A/B/
A+B) is not set to “OFF”.
• Check that headphones are not connected.
• Press MUTING to cancel the muting
function.
• Try pressing the input button on the remote
control or turning INPUT SELECTOR on
the receiver to select the equipment of
your choice (page 20).
• The protective device on the receiver has
been activated. Turn off the receiver,
eliminate the short-circuit problem, and
turn on the power again.
There is severe hum or noise.
• Check that the speakers and equipment are
connected securely.
• Check that the connecting cords are away
from a transformer or motor, and at least
3 meters (10 feet) away from a TV set or
fluorescent light.
• Move your audio equipment away from
the TV.
• The plugs and jacks are dirty. Wipe them
with a cloth slightly moistened with
alcohol.
30GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB06REM_STR-DH130U2.fm
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and equipment are
connected correctly and securely.
• Adjust the speaker balance (page 27).
There is severe hum, interrupted noise
or distortion from the equipment
connected to the PORTABLE IN jack.
• Check that the equipment are connected
securely.
• This is not a malfunction and will depend
on the connected equipment.
Recording cannot be carried out.
• Check that the equipment are connected
correctly.
• Select the source equipment using the
input buttons (page 20).
• Copyright protection to prevent recording
is contained in the sources. In this case,
you may not be able to record from the
sources.
Tuner function is not selectable.
• Consult your nearest Sony dealer.
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied)
to connect the receiver to an outdoor FM
antenna (aerial) as shown below.
Radio stations cannot be tuned in.
• Check that the antennas (aerials) are
connected securely. Adjust the antennas
(aerials) and connect an external antenna
(aerial), if necessary.
• The signal strength of the stations is too
weak with automatic tuning. Use direct
tuning.
• Make sure you set the tuning scale
correctly (when tuning in AM stations
with direct tuning) (page 23).
• No stations have been preset or the preset
stations have been cleared (when tuning by
scanning preset stations is used). Preset the
stations (page 24).
• Press DISPLAY repeatedly so that the
frequency appears on the display panel.
RDS does not work.*
• Make sure that you are tuned to an FM
RDS station.
• Select a stronger FM station.
• The station you tuned to is not transmitting
the RDS signal or the signal strength is
weak.
The RDS information that you want
does not appear.*
• The service may be temporarily out of
order. Contact the radio station and find
out whether they actually provide the
service in question.
* Europe model only.
Outdoor FM antenna (aerial)
Receiver
31GB
STR-DH130
4-294-472-11(1)
Additional Information
Tuner
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB06REM_STR-DH130U2.fm
Remote control
masterpage: Left
Specifications
The remote control does not function.
• Point the remote control at the remote
control sensor on the receiver.
• Remove any obstacles in the path between
the remote control and the receiver.
• Replace all the batteries in the remote
control with new ones, if they are weak.
• Make sure you select the correct input on
the remote control.
Error messages
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(USA model only)
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
If there is a malfunction, a message appears on
the display panel. You can check the condition
of the system by the message. If any problem
persists, consult your nearest Sony dealer.
PROTECT
Irregular current is output to the speakers, or
the receiver is covered and ventilation holes
are blocked. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
Clearing the memory
Reference section
To clear
See
All memorized settings
page 18
USA, Canada and Europe models1)
Minimum RMS Output Power (8 ohms, 20 Hz –
20 kHz, THD 0.09%)
90 W + 90 W
Stereo Mode Output Power (8 ohms, 1 kHz,
THD 1%)
100 W + 100 W
1)
Measured under the following conditions:
Area
Power requirements
USA, Canada
120 V AC, 60 Hz
Europe
230 V AC, 50 Hz
Frequency response
Analog
10 Hz – 70 kHz
+0.5/–2 dB (with BASS =
0 dB, TREBLE = 0 dB)
Input
Analog (PORTABLE IN)
Sensitivity: 1 V/
50 kilohms
S/N2): 96 dB (A, 500 mV3))
Inputs
Analog (Except PORTABLE IN)
Sensitivity: 500 mV/
50 kilohms
S/N2): 96 dB (A, 500 mV3))
Outputs
Analog (AUDIO OUT)
Voltage: 500 mV/
10 kilohms
32GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB06REM_STR-DH130U2.fm
Tone
Gain levels
masterpage: Right
±10 dB, 1 dB step
2) INPUT SHORT (with BASS = 0 dB, TREBLE =
0 dB).
3) Weighted
network, input level.
FM tuner section
Tuning range
87.5 MHz – 108.0 MHz
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
AM tuner section
Tuning range
Area
Tuning scale
10 kHz step
9 kHz step
USA, Canada
530 kHz –
1,710 kHz
531 kHz –
1,710 kHz
Europe
–
531 kHz –
1,602 kHz
Antenna (aerial)
Loop antenna (aerial)
General
Power requirements
Power requirements
USA, Canada
120 V AC, 60 Hz
Europe
230 V AC, 50/60 Hz
Additional Information
Area
Power consumption 200 W
Power consumption (during standby mode)
0.3 W
Dimensions (w/h/d) (Approx.)
430 mm × 132.5 mm ×
279 mm (17 in × 5 1/4 in ×
11 in) including projecting
parts and controls
Mass (Approx.)
6.4 kg (14 lb 2 oz)
Design and specifications are subject to
change without notice.
Halogenated flame retardants are not used in
the certain printed wiring boards.
33GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB01COV_STR-DH130U2IX.fm
masterpage: Left
Index
A
S
AUTO.STBY 27
Satellite tuner
connecting 16
Sleep Timer 11
Speakers
connecting 14
installing 13
Super Audio CD player
connecting 14
B
BALANCE 27
BASS 19
Blu-ray Disc player
connecting 16
C
Cable TV tuner
connecting 16
CD player
connecting 14
Clear
memory 18
remote control 28
D
DVD player
connecting 16
DVD recorder
connecting 16
T
Tape deck
connecting 14
TREBLE 19
Tuner
connecting 17
Tuning
automatically 23
directly 23
to preset stations 25
V
VCR
connecting 16
E
Error messages 32
I
Initial setup 18
M
MD deck
connecting 14
Muting 20
N
Naming
inputs 20
preset stations 25
R
RDS 26
Recording 22
Remote control 10
34GB
STR-DH130
4-294-472-11(1)
D:\NORM'S JOB\SONY HA\SO0173\STR-DH130\4294472111_GB\GB01COV_STR-DH130U2IX.fm
masterpage: Left
©2012 Sony Corporation Printed in Malaysia
model name1[STR-DH130]
[4-294-472-11(1)]