filename[D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CEL.fm]
masterpage:Right
4-174-068-11(1)
Multi Channel AV
Receiver
Operating Instructions
STR-DN1010
©2010 Sony Corporation
model name1[STR-DN1010]
[4-174-068-11(1)]
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB02REG_STR-DN1010-CEL.fm4-174068-11(1)
masterpage: Left
For customers in the United
States
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the apparatus with
newspapers, tablecloths, curtains, etc.
Do not place the naked flame sources such as lighted
candles on the apparatus.
Owner’s Record
The model and serial numbers are located on the rear
of the unit. Record these numbers in the space
provided below. Refer to them whenever you call
upon your Sony dealer regarding this product.
Model No. _____________________________________________________
Serial No. ______________________________________________________
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing, and
do not place objects filled with liquids, such as
vases, on the apparatus.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
As the main plug is used to disconnect the unit from
the mains, connect the unit to an easily accessible
AC outlet. Should you notice an abnormality in the
unit, disconnect the main plug from the AC outlet
immediately.
Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or
the like.
The unit is not disconnected from the mains as long
as it is connected to the AC outlet, even if the unit
itself has been turned off.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
This symbol is intended to alert
the user to the presence of the Hot
Surface that may be hot if it is
touched during the normal
operation.
Important Safety Instructions
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10)Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11)Only use attachments/accessories specified by
the manufacturer.
2GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB02REG_STR-DN1010-CEL.fm
12)Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or
when unused for long periods of time.
14)Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
masterpage: Right
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
To reduce the risk of electric shock, the speaker cord
should be connected to the apparatus and the
speakers in accordance with the following
instructions.
1) Disconnect the AC power cord from the MAINS.
2) Strip 10 to 15 mm of the wire insulation of the
speaker cord.
3) Connect the speaker cord to the apparatus and
the speakers carefully so as not to touch the core
of speaker cord by hand. Also disconnect the AC
power cord from the MAINS before
disconnecting the speaker cord from the
apparatus and the speakers.
The following FCC statement
applies only to the version of
this model manufactured for
sale in the U.S.A. Other
versions may not comply with
FCC technical regulations.
For customers in Europe
NOTE:
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. The recycling of materials
will help to conserve natural resources. For more
detailed information about recycling of this product,
please contact your local Civic Office, your
household waste disposal service or the shop where
you purchased the product.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
continued
3GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB02REG_STR-DN1010-CEL.fm4-174068-11(1)
Disposal of waste batteries
(applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the battery or on the packaging
indicates that the battery provided with this product
shall not be treated as household waste.
On certain batteries this symbol might be used in
combination with a chemical symbol. The chemical
symbols for mercury (Hg) or lead (Pb) are added if
the battery contains more than 0.0005% mercury or
0.004% lead.
By ensuring these batteries are disposed of correctly,
you will help prevent potentially negative
consequences for the environment and human health
which could otherwise be caused by inappropriate
waste handling of the battery. The recycling of the
materials will help to conserve natural resources.
In case of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery, this battery
should be replaced by qualified service staff only.
To ensure that the battery will be treated properly,
hand over the product at end-of-life to the applicable
collection point for the recycling of electrical and
electronic equipment.
For all other batteries, please view the section on
how to remove the battery from the product safely.
Hand the battery over to the applicable collection
point for the recycling of waste batteries.
For more detailed information about recycling of
this product or battery, please contact your local
Civic Office, your household waste disposal service
or the shop where you purchased the product.
masterpage: Left
About This Manual
• The instructions in this manual are for model
STR-DN1010. Check your model number by
looking at the lower right corner of the front panel.
In this manual, models of area code U2 is used for
illustration purposes unless stated otherwise. Any
difference in operation is clearly indicated in the
text, for example, “Models of area code ECE
only”.
• The instructions in this manual describe the
controls on the supplied remote. You can also use
the controls on the receiver if they have the same
or similar names as those on the remote.
About area codes
The area code of the receiver you purchased is
shown on the lower right portion of the rear panel
(see the illustration below).
4-XXX-XXX-XX (X) AA
Area code
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
Notice for customers: The following
information is only applicable to
equipment sold in countries applying
EU Directives.
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo,
108-0075 Japan. The Authorized Representative for
EMC and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters
please refer to the addresses given in separate
service or guarantee documents.
For customers in Australia
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
4GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB02REG_STR-DN1010-CEL.fm
On copyrights
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the
double-D symbol are trademarks of Dolby
Laboratories.
** Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS is a
registered trademark and the DTS logos, Symbol,
DTS-HD and DTS-HD Master Audio are
trademarks of DTS, Inc. © 1996-2008 DTS, Inc.
All Rights Reserved.
masterpage: Right
“BRAVIA” is a trademark of Sony Corporation.
“PlayStation” is a registered trademark of Sony
Computer Entertainment Inc.
“S-AIR” and its logo are trademarks of Sony
Corporation.
DLNA and DLNA CERTIFIED are trademarks
and/or service marks of the Digital Living Network
Alliance.
This receiver incorporates High-Definition
Multimedia Interface (HDMITM) technology.
HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
SIRIUS, XM and all related marks and logos are
trademarks of Sirius XM Radio Inc. and its
subsidiaries. All rights reserved. Service not
available in Alaska and Hawaii.
The font type (Shin Go R) installed in this receiver
is provided by MORISAWA & COMPANY LTD.
These names are the trademarks of MORISAWA &
COMPANY LTD., and the copyright of the font also
belongs to MORISAWA & COMPANY LTD.
iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
All other trademarks and registered trademarks are
of their respective holders. In this manual, ™ and ®
marks are not specified.
The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Sony Corporation is under license.
Other trademarks and trade names are those of their
respective owners.
“M-crew Server” is a trademark of Sony
Corporation.
“x.v.Color (x.v.Colour)” and “x.v.Color
(x.v.Colour)” logo are trademarks of Sony
Corporation.
5GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CELTOC.fm
masterpage: Left
Table of Contents
About This Manual........................................4
Supplied accessories......................................8
Description and location of parts...................9
Connections
1: Installing the speakers .............................19
2: Connecting the speakers ..........................21
3: Connecting the TV ..................................23
4a: Connecting the audio components.........24
4b: Connecting the video components ........26
5: Connecting the antennas (aerials)............35
6: Inserting the wireless transmitter/
transceiver...............................................35
7: Connecting the AC power cord
(mains lead) ............................................36
Preparing the Receiver
Initializing the receiver ................................37
Selecting the front speaker system ..............37
Calibrating the appropriate speaker settings
automatically (Auto Calibration)............38
Guide to on-screen display operation ..........44
Basic Operations
Playback ......................................................46
Enjoying sound/images from the components
connected to the DIGITAL MEDIA
PORT ......................................................48
Using the Sleep Timer .................................52
Recording using the receiver .......................52
Tuner Operations
Listening to FM/AM radio.......................... 53
Presetting FM/AM radio stations
(Preset Tuning)....................................... 55
Using the Radio Data System (RDS).......... 56
(Models of area code CEK, ECE, AU1,
TW2 only)
Listening to Satellite Radio......................... 57
(Models of area code U2, CA2 only)
Connecting the SIRIUS Satellite Radio...... 58
Preparing to listen to the SIRIUS Satellite
Radio...................................................... 58
Selecting a channel of the SIRIUS Satellite
Radio...................................................... 59
Presetting SIRIUS Satellite Radio
channels ................................................. 61
Restricting access to specific channels
(Parental Lock) ...................................... 62
Enjoying Surround Sound
Selecting the sound field............................. 65
Enjoying the surround effect at low volume
levels (NIGHT MODE) ......................... 69
Resetting sound fields to the initial
settings ................................................... 69
“BRAVIA” Sync Features
What is “BRAVIA” Sync? .......................... 70
Preparing for the “BRAVIA” Sync ............. 70
Playing back components with one-touch
operation (One-Touch Play)................... 72
Enjoying the TV sound from the speakers
connected to the receiver
(System Audio Control)......................... 72
Turning off the receiver with the TV
(System Power Off) ............................... 73
Enjoying movies with the optimum sound
field (Theater/Theatre Mode Sync)........ 73
Enjoying the TV sound via an HDMI cable
(Audio Return Channel)......................... 74
6GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CELTOC.fm
masterpage: Right
S-AIR Operations
About S-AIR products ................................ 75
Setting up an S-AIR product....................... 76
Enjoying the system’s sound in another
room ....................................................... 80
Changing the channel for better sound
transmission ........................................... 81
Stabilizing S-AIR reception ........................ 82
Enjoying the S-AIR receiver while the
S-AIR main unit is in standby mode...... 83
Advanced Operations
Switching between digital and analog audio
(INPUT MODE) .................................... 84
Enjoying the sound/images from other
inputs...................................................... 85
Using a bi-amplifier connection.................. 88
Using the setting menu................................ 89
Auto Calibration menu................................ 90
Speaker Settings menu ................................ 91
Surround Settings menu .............................. 95
EQ Settings menu........................................ 96
Audio Settings menu................................... 96
Video Settings menu ................................... 97
HDMI Settings menu .................................. 98
System Settings menu ............................... 100
Operating without connecting to a TV...... 101
Using the Remote
Programming the remote........................... 112
Clearing all the contents of the remote’s
memory ................................................ 116
Additional Information
Glossary .................................................... 117
Precautions ................................................ 120
Troubleshooting ........................................ 122
Specifications ............................................ 129
Index.......................................................... 132
7GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CELTOC.fm
Supplied accessories
•
•
•
•
Operating Instructions (this manual)
Quick Setup Guide
GUI Menu List
FM wire antenna (aerial) (1)
• AM loop antenna (aerial) (1)
masterpage: Left
Inserting batteries into the
remote
Insert two R6 (size-AA) batteries in the
RM-AAP051 (Models of area code U2, CA2
only) or RM-AAP052 (Models of area code
CEK, ECE, AU1, TW2 only) Remote
Commander.
Observe the correct polarity when installing
batteries.
• Remote commander (1)
– RM-AAP051 (Models of area code U2,
CA2 only)
– RM-AAP052 (Models of area code ECE,
CEK, AU1, TW2 only)
Notes
• R6 (size-AA) batteries (2)
• Optimizer microphone (ECM-AC2) (1)
• Do not leave the remote in an extremely hot or
humid place.
• Do not use a new battery with old ones.
• Do not mix manganese batteries and other kinds of
batteries.
• Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
• If you do not intend to use the remote for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace the batteries, the programmed
remote codes may be cleared. If this happens,
program the remote codes again (page 112).
• When the remote no longer operates the receiver,
replace all the batteries with new ones.
8GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
masterpage: Right
Description and location of parts
Front panel
1
qh
2
3
qg
4
qf
5
qd
6
qs qa
7
0
8
9
Name and function
Name and function
A ?/1 (on/standby)
Turns the receiver on or off (page 37, 55, 69).
G MUTING
Turns off the sound temporarily.
Press MUTING again to restore the sound (page
47, 122).
B Remote sensor
Receives signals from remote commander.
C White indicator
Lights up when the receiver is on.
Lights off when the receiver is off.
D MULTI CHANNEL DECODING indicator
Lights up when multi channel audio signals are
decoded (page 124).
E Display
Displays the current status of the selected
component or a list of selectable items (page 11).
F INPUT SELECTOR +/–
Selects the input source to playback (page 46,
52, 84).
H MASTER VOLUME
Adjusts the volume level of all speakers at the
same time (page 46, 122).
I VIDEO 2 IN jacks
Connects to a portable audio/video component
such as a camcorder or video game (page 33).
J AUTO CAL MIC jack
Connects to the supplied optimizer microphone
for the Auto Calibration function (page 39).
K DISPLAY
Selects the information displayed on the display
(page 47, 128).
continued
9GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
masterpage: Left
Name and function
L DIMMER
Adjusts the brightness of the display (page 111).
M INPUT MODE
Selects the input mode when the same
components are connected to both digital and
analog jacks (page 84).
N 2CH/A.DIRECT, A.F.D., MOVIE, MUSIC
Selects a sound field (page 65, 66).
O SPEAKERS
Selects the front speaker system (page 37).
P PHONES jack
Connects to headphones (page 122).
10GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
masterpage: Right
About the indicators on the display
1
2
LH SW RH
L
C
R
SL
S
SR
3
4
5
6 7
8
9
ARC
D + EX TrueHD NEO 6
PL ll x z ANALOG HDMI COAX OPT
S –AIR
EQ RDS CAT MEM DTS – HD MSTR HI RES LBR
LF E
D.RANGE SIRIUS ST
DTS –ES 96 24 LPCM SLEEP BI–AMP SP A B
SB L SB SB R
qk
qj
qh qg
qf
qd
qs
qa
q;
Indicator and explanation
Indicator and explanation
A SW
E Dolby Digital Surround indicators
Lights up one of the respective indicators when
the receiver is decoding the corresponding
Dolby Digital format signals.
Lights up when the audio signal is output from
the SUBWOOFER jack.
B Dolby Pro Logic indicators
Lights up one of the respective indicators when
the receiver performs Dolby Pro Logic
processing. This matrix surround decoding
technology can enhance input signals.
PL
PL II
PL IIx
PL IIz
Dolby Pro Logic
Dolby Pro Logic II
Dolby Pro Logic IIx
Dolby Pro Logic IIz
Note
These indicators may not light up depending on
the speaker pattern setting.
C Input indicators
Light up to indicate the current input.
ANALOG
Lights up when
– INPUT MODE is set to “ANALOG”.
– Sound Field is set to “Analog Direct”.
– No digital signals are detected.
HDMI
The receiver recognizes a component connected
via an HDMI IN jack.
COAX
When INPUT MODE is set to “AUTO” and the
source signal is a digital signal being input
through the COAXIAL jack (page 84).
OPT
When INPUT MODE is set to “AUTO” and the
source signal is a digital signal being input
through the OPTICAL jack (page 84).
D ARC
Lights up when TV input is selected and the
Audio Return Channel (ARC) signals are
detected (page 100).
D
D EX
D+
TrueHD
Dolby Digital
Dolby Digital Surround EX
Dolby Digital Plus
Dolby TrueHD
Note
When playing a Dolby Digital format disc, be
sure that you have made digital connections and
that INPUT MODE is set to “AUTO” (page 84).
F NEO:6
Lights up when DTS Neo:6 Cinema/Music
decoder is activated (page 66).
G DTS-HD indicators
Lights up one of the respective indicators when
the receiver is decoding the corresponding
DTS-HD format signals.
DTS-HD MSTR DTS-HD Master Audio
DTS-HD HI RES DTS-HD High Resolution
Audio
DTS-HD Low Bit Rate
DTS-HD LBR
Audio
H S-AIR
Lights up when the S-AIR transmitter (not
supplied) is inserted.
I SP A/SP B/SP A B
Lights up according to the front speaker system
used (page 37).
However, these indicators do not light up if the
speaker output is turned off or if headphones are
connected.
J BI-AMP
Lights up when surround back speakers
selection is set to “BI-AMP” (page 88).
continued
11GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
masterpage: Left
Indicator and explanation
Indicator and explanation
K SLEEP
Lights up when the Sleep Timer is activated.
R Playback channel indicators
The letters (L, C, R, etc.) indicate the channels
being played back. The boxes around the letters
vary to show how the receiver downmixes or
upmixes the source sound (based on the speaker
pattern settings).
L LPCM
Lights up when Linear PCM (Pulse Code
Modulation) signals are decoded.
M DTS(-ES) indicators
Lights up one of the respective indicators when
the receiver is decoding the corresponding DTS
format signals.
DTS
DTS-ES
DTS 96/24
DTS
DTS-ES
DTS 96 kHz/24 bit
Note
When playing a DTS format disc, be sure that
you have made digital connections and that
INPUT MODE is set to “AUTO” (page 84).
N Tuning indicators
Lights up when the receiver tunes in radio
stations, or satellite radio stations.
RDS (Models of area code CEK, ECE,
AU1, TW2 only)
A station that provides RDS services is tuned in.
CAT (Models of area code U2, CA2 only)
The category mode is selected during the
satellite radio operation.
MEM
A memory function, such as Preset Memory
(page 55), etc., is activated.
SIRIUS (Models of area code U2, CA2
only)
The SiriusConnect Home tuner is connected and
“SR” is selected.
ST
Stereo broadcast
LH
RH
L
R
C
SL
SR
S
SBL
SBR
SB
Front Left High
Front Right High
Front Left
Front Right
Center (monaural)
Surround Left
Surround Right
Surround (monaural or the
surround components
obtained by Pro Logic
processing)
Surround Back Left
Surround Back Right
Surround Back (the
surround back components
obtained by 6.1 channel
decoding)
Example:
Speaker pattern: 3/0.1
Recording format: 3/2.1
Sound Field: A.F.D. AUTO
O EQ
Lights up when the equalizer is activated.
P D.RANGE
Lights up when dynamic range compression is
activated (page 94).
Q
Lights up when the disc being played back
contains an LFE (Low Frequency Effect)
channel and the LFE channel signal is actually
being reproduced.
12GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
masterpage: Right
Rear panel
1
8
2 3
6
7
6
A S-AIR section
EZW-T100
slot
5
D DIGITAL INPUT/OUTPUT section
Connects to a
wireless transmitter
(not supplied)
(page 35).
B DMPORT section
DMPORT
jack
4
Connects to a Sony
DIGITAL MEDIA
PORT adapter
(page 24).
OPTICAL
IN jacks
COAXIAL
IN jack
HDMI IN/
OUT* jacks
C ANTENNA section
FM
ANTENNA
jack
Connects to the
supplied FM wire
antenna (aerial)
(page 35).
AM
ANTENNA
terminals
Connects to the
supplied AM loop
antenna (aerial)
(page 35).
SIRIUS jack
(Models of
area code U2,
CA2 only)
Connects to a
SiriusConnect Home
tuner (not supplied)
(page 58).
Connects to a
Blu-ray disc player,
etc. (page 23, 30,
31, 32).
Connects to a DVD
player, satellite
tuner, Blu-ray disc
player, etc. The
image is output to a
TV or a projector
while the sound can
be output from a TV
or/and speakers
connected to this
receiver (page 23,
27).
E SPEAKERS section
Connects to
speakers (page 21).
continued
13GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
F AUDIO INPUT/OUTPUT section
AUDIO IN/
White (L) OUT jacks
Connects to a Super
Audio CD player,
etc. (page 23, 24).
Red (R)
Black
AUDIO OUT Connects to a
jack
subwoofer
(page 21).
G VIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
White (L) OUT jacks
Red (R)
Yellow
Connects to a VCR,
Blu-ray disc player,
etc. (page 30, 32,
33).
VIDEO IN/
OUT* jacks
masterpage: Left
Remote commander
You can use the supplied remote to operate the
receiver and to control the Sony audio/video
components that the remote is assigned to
operate.
You can also program the remote to control
non-Sony audio/video components. For
details, see “Programming the remote”
(page 112).
• RM-AAP051 (Models of area
code U2, CA2 only)
• RM-AAP052 (Models of area
code CEK, ECE, AU1, TW2
only)
H COMPONENT VIDEO INPUT/
OUTPUT section
Green
(Y)
Blue
(PB/CB)
Y, PB/CB,
PR/CR IN/
OUT* jacks
Connects to a
Blu-ray disc player,
TV, satellite tuner,
etc. (page 23, 30, 31,
32).
Red
(PR/CR)
* You can watch the selected input image when you
connect the MONITOR OUT or HDMI TV OUT
jack to a TV (page 23).
14GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
masterpage: Right
Name and function
wg
wf
wd
ws
A ?/1 (on/standby)
1
2
3
Turns the receiver on or sets it to the standby
mode.
To turn off all components, press ?/1 and
AV ?/1 (B) at the same time (SYSTEM
STANDBY).
Saving the power in standby mode.
When “Ctrl for HDMI” is set to “OFF” (page
70) and “S-AIR Stby” is set to “OFF” (page 83).
4
wa
w;
5
6
ql
7
Turns on or off the audio/video components that
the remote is programmed to operate.
To turn the TV on or off, press TV (W) and
then press AV ?/1.
If you press ?/1 (A) at the same time, it will
turn off the receiver and other components
(SYSTEM STANDBY).
Note
The function of the AV ?/1 switch changes
automatically each time you press the input
buttons (D).
C AMP
The button lights up and activates the receiver
operation (page 101).
qk
qj
B AV ?/1a) (on/standby)
8
9
0
qh
qg
qf
qa
qd
qs
D Input buttons (VIDEO 1b))
Selects the component you want to use. When
you press any of the input buttons, the receiver
turns on. The buttons are initial assigned to
control Sony components. You can program the
remote to control non-Sony components
following the steps in “Programming the
remote” on page 112.
Numeric buttonsa) (number 5b))
Press SHIFT (V), then press numeric buttons
to
– preset/tune to preset stations.
– select track numbers. Press 0/10 to select track
number 10.
– select channel numbers.
Press TV (W), then press the numeric buttons
to select the TV channels.
-/--a)
Press SHIFT (V), then press -/-- to select the
channel entry mode, either one or two digit.
To select the channel entry mode of the TV,
press TV (W) and then press -/--.
>10a)
Press SHIFT (V), then press >10 to select track
numbers over 10. You can also select the
channel numbers of the DIGITAL CATV
terminal.
continued
15GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
Name and function
Name and function
ENTERa)
Press SHIFT (V), then press ENTER to enter
the value after selecting a channel, disc or track
using the numeric buttons.
To enter the value of Sony TV, press TV (W)
and then press ENTER.
MEMORY
Press SHIFT (V), then press MEMORY to
store a station during tuner operation.
/a) (Text) (RM-AAP052 only)
Press TV (W), then press / to display text.
E SOUND FIELD +/–
Selects a sound field (page 65).
F Color buttonsa)
Displays an operation guide on the TV screen
when the color buttons are available. Follow the
operation guide to perform a selected operation.
G GUI MODE
Displays the GUI menu on the TV screen.
H TOOLS/OPTIONSa)
Displays and selects items from the option
menus.
To display the options of Sony TV, press TV
(W) and then press TOOLS/OPTIONS.
I MENU, HOMEa)
Displays the menu to operate the audio/video
components.
To display the menus of Sony TV, press TV
(W) and then press HOME.
J
./>a), m/Ma),
masterpage: Left
Na)b),
Xa),
xa)
Skip, backward/forward, play, pause, stop
operation.
/ < a)
Replay the previous scene or fast forward the
current scene.
<
CATEGORY +/– (RM-AAP051 only)
Selects a category for satellite tuner (page 60,
110).
CATEGORY MODEb) (RM-AAP051 only)
Selects the category mode for satellite tuner
(page 59, 110).
TUNING +/–a)
Scans a station.
D.TUNING
Enters direct tuning mode (page 54, 109).
K TV CH +b)/–a) (RM-AAP051 only)
PROG +b)/–a) (RM-AAP052 only)
Press TV (W), then press TV CH +/– or
PROG +/– to select preset TV channels.
PRESET +b)/–a)
Selects
– preset stations.
– preset channels.
cb)/C (RM-AAP052 only)
In text mode: Press TV (W), then press c/C
to select the next or previous page.
L F1a), F2a)
Press BD or DVD (D), then press F1 or F2 to
select a component.
• DVD/HDD COMBO
F1: HDD
F2: DVD disc, Blu-ray disc
• DVD/VCR COMBO
F1: DVD disc, Blu-ray disc
F2: VHS
SLEEP
Activates the Sleep Timer function and the
duration which the receiver turns off
automatically (page 52).
M BD/DVD TOP MENUa)
Displays the menu or on-screen guide on the TV
screen. Then, use V/v/B/b (R) and
(R) to
perform menu operations.
BD/DVD MENUa)
Displays the menu on the TV screen. Then, use
V/v/B/b (R) and
(R) to perform menu
operations.
TV INPUTa) (RM-AAP051 only)
a) (Input select) (RM-AAP052 only)
Press TV (W), then press TV INPUT or
to
select the input signal (TV input or video input).
a)
(Text hold) (RM-AAP052 only)
In text mode: Press TV (W), then press
hold the current page.
to
WIDEa) (RM-AAP051 only)
a)
(Wide mode) (RM-AAP052 only)
Press TV (W), then press WIDE or
repeatedly to select the wide picture mode.
N MUTINGa) (RM-AAP051 only)
a) (RM-AAP052 only)
Activates the muting function. Press the button
again to restore the sound. To activate the TV’s
muting function, press TV (W) and then press
MUTING or
.
16GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
Name and function
O TV
Name and function
VOL +/–a)
a)
(RM-AAP051 only)
+/– (RM-AAP052 only)
Press TV (W), then press TV VOL +/– or
+/– to adjust the TV volume level.
MASTER VOL +/–a) (RM-AAP051 only)
+/–a) (RM-AAP052 only)
Adjust the volume level of all speakers at the
same time.
P DISC SKIPa)
Skips disc when using a multi-disc changer.
Q RETURN/EXIT Oa)
Returns to the previous menu or exits the menu
while the menu or on-screen guide is displayed
on the TV screen.
To return to the previous menu of Sony TV,
press TV (W) and then press RETURN/EXIT
O.
R
a)
a)
, V/v/B/b
Press V/v/B/b to select the menu items, then
press
to enter the selection.
S GUIDEa) (RM-AAP051 only)
a)
(Guide) (RM-AAP052 only)
Press TV (W), then press GUIDE or
display the on-screen program guide.
masterpage: Right
to
T DISPLAYa)
Views information on the display.
X THEATER (RM-AAP051 only)
THEATRE (RM-AAP052 only)
Sets the optimal picture settings automatically
for watching movies when you connect a Sony
TV that is compatible with the THEATER or
THEATRE button function (page 73).
Y RM SET UP
Set up the remote.
a) See
the table on page 18 for information on the
buttons that you can use to control each
component.
b) The following buttons have tactile dots. Use the
tactile dots as reference when operating the
receiver.
– number 5, VIDEO 1
– N, CATEGORY MODE (RM-AAP051 only)
– PRESET +, TV CH + (RM-AAP051 only),
PROG + (RM-AAP052 only), c
(RM-AAP052 only)
Notes
• Some functions explained in this section may not
work depending on the model.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
DISPLAYa) (RM-AAP051 only)
Press TV (W), then press DISPLAY to display
information of TV.
,
(Info, Text reveal) (RM-AAP052
only)
Press TV (W), then press
to display
information such as current channel number and
screen mode.
In text mode: Press TV (W), then press
to
reveal hidden information (e.g. answers to a
quiz).
U NIGHT MODE
Activates the Night Mode function (page 69).
V SHIFT
The button lights up and activates the buttons
with pink printing.
W TV
The button light up and activates the buttons
with yellow printing.
continued
17GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB03DES_STR-DN1010-CEL.fm
masterpage: Left
To control other Sony components
TV VCR
Name
DVD Blu-ray HDD PSX Video
Digital DSS*1 Digital Tape DAT CD DIGITAL
player, disc Recorder
CD
CATV
satellite/ deck deck player, MEDIA
DVD/ player
player, terminal*1
terrestrial A/B
MD PORT
VCR
LD
receiver*2
deck device
combo
player
B AV ?/1
z
z
z
z
z
z
z
z
z
z
D Numeric
buttons
z
z
z
z
z
z
z
z
z
z
-/--, >10
z
z
z
z
z
z
z
z
z
z
ENTER
z
z
z
z
z
z
z*4
z
z
z
F Color buttons z
z*3
z
z
H TOOLS/
OPTIONS
z
z
z
z
*2
z
(Text)
z
z
z
z
z
J ./>
z
z
z
z
z
z
z
z
z
/
z
<
z
z
z*5 z
z
z
z
z
I MENU, HOME z
<
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z*7
z
z
z
z
m/TUNING –, z
M/TUNING +
z
z
z
z
z
z
N, X, x
z
z
z
z
z
z
z
z
K PRESET +/–,
TV CH +/–*1,
PROG +/–*2
z
z
z
z
z
z*4
z
z
z
L F1, F2
z
z
M BD/DVD TOP
MENU, BD/
DVD MENU
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z*3
z
z
z
z
z
z
z
z
TV INPUT*1,
*2
(Input
*2
select),
(Text hold),
*2
WIDE*1,
(Wide mode)
z
z
z
N MUTING*1,
z
O MASTER
VOL +/–*1, TV
VOL +/–*1,
+/–*2
z
*2
P DISC SKIP
Q RETURN/
EXIT O
z
R V/v/B/b,
S GUIDE*1,
(Guide)
z
*2
T DISPLAY
*1
*2
*3
*4
RM-AAP051 only.
RM-AAP052 only.
DVD player only.
LD player only.
z
z
z
z
z*6
z
z
*5
*6
*7
z
z
z
z
z
Deck B only.
Video CD only.
m/M only.
18GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
Connections
Connections
1: Installing the speakers
This receiver allows you to use a 7.1 channel
system (7 speakers and one subwoofer).
Example of speaker system
configuration
To fully enjoy theater-like multi channel
surround sound requires five speakers (two
front speakers, a center speaker, and two
surround speakers) and a subwoofer (5.1
channel).
You can enjoy high fidelity reproduction of
DVD software recorded sound in the Surround
EX format if you connect additional one
surround back speaker (6.1 channel) or two
surround back speakers (7.1 channel).
You can enjoy vertical sound effects if you
connect additional two front high speakers
(7.1 channel) in PLIIz mode (page 66).
AFront speaker (Left)
BFront speaker (Right)
CCenter speaker
DSurround speaker (Left)
ESurround speaker (Right)
FSurround back speaker (Left)*
GSurround back speaker (Right)*
HFront high speaker (Left)*
IFront high speaker (Right)*
JSubwoofer
* You cannot use the surround back speakers
and the front high speakers simultaneously.
continued
19GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
Tips
• When you connect a 7.1 channel speaker system
with two surround back speakers, all angle A
should be the same.
• When you connect a 7.1 channel speaker system
with two front high speakers, place the front high
speakers
– at an angle between 22° to 45°.
– at least 3.3 feet (1 meter) directly above the front
speakers.
• When you connect a 6.1 channel speaker system,
place the surround back speaker behind the
listening position.
• Since the subwoofer does not emit highly
directional signals, you can place it wherever you
want.
20GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
2: Connecting the speakers
Connections
Before connecting cords, be sure to disconnect the AC power cord (mains lead).
Surround speaker
Center speaker
Right
B
Left
B
B
A
B
13/32"
(10 mm)
Right
Subwoofer b)
Left
Surround back/Front high/
Bi-amplifier/Front B
speakera)
Right
Left
Front A speaker
A Monaural audio cord (not supplied)
B Speaker cord (not supplied)
continued
21GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
a)
Notes on the SPEAKERS SURROUND BACK/
FRONT HIGH/BI-AMP/FRONT B terminals
connection.
– If you connect only one surround back speaker,
connect it to L of this terminals.
– If you are not using surround back speaker or
front high speakers, and you have an additional
front speaker system, connect the additional
front speaker system to this terminals.
Set “SB Assign” to “Speaker B” in the Speaker
Settings menu (page 91).
You can select the front speaker system you
want using the SPEAKERS button on the
receiver (page 37).
– If you are not using surround back speaker or
front high speakers, you can connect the front
speakers to this terminals using bi-amplifier
connection (page 22).
Set “SB Assign” to “BI-AMP” in the Speaker
Settings menu (page 91).
b) When you connect a subwoofer with an auto
standby function, turn off the function when
watching movies. If the auto standby function is
set to on, it turns to standby mode automatically
based on the level of the input signal to a
subwoofer, then sound may not be output.
Bi-amplifier connection
If you are not using surround back speakers or
front high speakers, you can connect the front
speakers to the SPEAKERS SURROUND
BACK/FRONT HIGH/BI-AMP/FRONT B
terminals using a bi-amplifier connection.
Front speaker
(Right)
Front speaker
(Left)
Hi
Hi
Lo
Lo
Notes
• Before connecting the AC power cord (mains
lead), make sure that metallic wires of the speaker
cords are not touching each other between the
SPEAKERS terminals.
• After you have install and connect your speaker, be
sure to select the speaker pattern from the Speaker
Settings menu (page 91).
Connect the jacks on the Lo (or Hi) side of the
front speakers to the SPEAKERS FRONT A
terminals, and connect the jacks on the Hi (or
Lo) side of the front speakers to the
SPEAKERS SURROUND BACK/FRONT
HIGH/BI-AMP/FRONT B terminals.
Make sure that metal fittings of Hi/Lo attached
to the speakers have been removed from the
speakers. Not doing so may cause a
malfunction of the receiver.
After you have made the bi-amplifier
connection, set “SB Assign” to “BI-AMP” in
the Speaker Settings menu (page 91).
22GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
3: Connecting the TV
It is not necessary to connect all the cables.
Connect audio and video cords according to
the jacks of your components.
Before connecting cords, be sure to disconnect
the AC power cord (mains lead).
TV
Video signals
Audio signals
Audio/video
signals
ARC
A
B
Ca)
D
A Component video cord (not supplied)
B Video cord (not supplied)
C Optical digital cord (not supplied)
D Audio cord (not supplied)
E HDMI cable (not supplied)
Ea)
b)
Recommended connection
Alternative connection
Sony recommends that you use an HDMI-authorized cable or Sony HDMI cable.
continued
23GB
STR-DN1010
4-174-068-11(1)
Connections
You can watch the selected input image when
you connect the HDMI TV OUT or
MONITOR OUT jack to a TV. You can
operate this receiver using a GUI (Graphical
User Interface) if you connect HDMI TV OUT
jack to a TV.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
a)
To enjoy TV multi channel surround sound
broadcasting from the speakers connected to the
receiver, connect C or E.
Be sure to turn off the TV’s volume or activate the
TV’s muting function.
b) If your TV is compatible with the Audio Return
Channel (ARC) function, the TV sound will output
from the speakers connected to the receiver via
HDMI TV OUT connection. In this case, set
“ARC” to “ON” in HDMI Settings menu
(page 100).
4a: Connecting the audio
components
The following illustration shows how to
connect a Super Audio CD player, CD player,
CD recorder and DIGITAL MEDIA PORT
adapter. Before connecting cords, be sure to
disconnect the AC power cord (mains lead).
Notes
• Be sure to turn on the receiver when the video and
audio signals of a playback component are being
output to a TV via the receiver. If the power supply
of the receiver is not turned on, neither video nor
audio signals will be transmitted.
• Connect image display components such as a TV
monitor or a projector to the HDMI TV OUT or
MONITOR OUT jack on the receiver. You may
not be able to record, even if you connect recording
components.
• Depending on the status of the connection between
the TV and the antenna (aerial), the image on the
TV screen may be distorted. In this case, place the
antenna (aerial) farther away from the receiver.
• When connecting optical digital cords, insert the
plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
Notes on connecting DIGITAL
MEDIA PORT adapter
Tips
To detach the DIGITAL MEDIA
PORT adapter from DMPORT
jack
• All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
• The receiver has a video conversion function. For
details, see “Function for conversion of video
signals” (page 34).
• When you connect the audio output jack of the TV
to the TV IN jacks of the receiver to output the TV
sound from the speakers connected to the receiver,
set the sound output jack of the TV to “Fixed” if it
can be switched between either “Fixed” or
“Variable”.
• Do not connect or disconnect the DIGITAL
MEDIA PORT adapter while the receiver is
turned on.
• Be sure to make DMPORT connections
firmly, insert the connector straight in.
• As the connector of the DIGITAL MEDIA
PORT adapter is fragile, be sure to handle
with care when placing or moving the
receiver.
• When connecting the DIGITAL MEDIA
PORT adapter, be sure the connector is
inserted with the arrow mark facing towards
the arrow mark on the DMPORT jack.
1
2
Press and hold both sides of the connector and
then pull out the connector.
24GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
A
TV*
Connections
Super Audio
CD player,
CD player,
CD recorder
masterpage: Right
B
DIGITAL MEDIA
PORT adapter
A Audio cord (not supplied)
B Video cord (not supplied)
* You can enjoy the images from the components
connected to the DIGITAL MEDIA PORT adapter
when you connect the TV to the receiver.
25GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
4b: Connecting the video components
Components to be connected
Connect your video components according to
the table below.
Component
Page
Blu-ray disc player*
27, 30
DVD player*
27, 31
DVD recorder*
27, 31
Satellite tuner*,
Cable TV tuner*
27, 32
“PlayStation 3”
27
Video input/output jacks to be
connected
The image quality depends on the connecting
jack. See the illustration that follows. Select
the connection according to the jacks on your
components.
COMPONENT VIDEO
Y
HDMI
PB/CB
VIDEO
VCR
33
Camcorder, video game, etc.
33
PR/CR
Digital
* We recommend that you connect your video
components via HDMI connection if they have
HDMI jacks.
If you want to connect several
digital components, but cannot
find an unused input
See “Enjoying the sound/images from other
inputs” (page 85).
Analog
High quality image
Converting video signals
This receiver is equipped with a function for
up-converting video signals. For details, see
“Function for conversion of video signals”
(page 34).
Notes
• Before connecting cords, be sure to disconnect the
AC power cord (mains lead).
• It is not necessary to connect all the cords. Connect
according to the availability of jacks on the
connected components.
• Be sure to turn on the receiver when the video and
audio signals of a playback component are being
output to a TV via the receiver. If the power supply
of the receiver is not turned on, neither video nor
audio signals will be transmitted.
• When connecting optical digital cords, insert the
plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
Tip
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
26GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
Connections
Connecting components with
HDMI jacks
HDMI is the abbreviated name for HighDefinition Multimedia Interface. It is an
interface which transmits video and audio
signals in digital format.
Sony recommends that you connect
components to the receiver using an HDMI
cable.
By connecting Sony “BRAVIA” Synccompatible components using HDMI cables,
operations can be simplified. See ““BRAVIA”
Sync Features” (page 70).
HDMI features
• A digital audio signals transmitted by HDMI
can be output from the speakers connected to
the receiver. This signal supports Dolby
Digital, DTS, and Linear PCM.
• The receiver can receive Multi Linear PCM
(up to 8 channels) with a sampling frequency
of 192 kHz or less with an HDMI
connection.
• Analog video signals input to the VIDEO
jack or COMPONENT VIDEO jacks can be
up-converted as HDMI signals (page 34).
Audio signals are not output from an HDMI
TV OUT jack when the image is converted.
• This receiver supports High Bitrate Audio
(DTS-HD Master Audio, Dolby TrueHD),
Deep Color (Deep Colour), x.v.Color
(x.v.Colour) and 3D transmission.
• This receiver supports the Control for HDMI
function. For details, see ““BRAVIA” Sync
Features” (page 70).
continued
27GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Satellite tuner,
Cable TV tuner
DVD player,
DVD recorder
Audio/video
signals
Audio/video
signals
A
masterpage: Left
Blu-ray disc player
Audio/video
signals
A
A
A
Audio/video
signals
“PlayStation 3”
A
Audio/video
signals
ARC
TV, etc.*
A HDMI cable (not supplied)
Sony recommends that you use an HDMI-authorized cable or Sony HDMI cable.
* For details on the audio connection of TV to the
receiver, see page 23.
Notes
• HDMI 3 input has a better sound quality. When
you need a higher sound quality, connect your
component to the HDMI IN 3 (for AUDIO) jack
and select HDMI 3 as input.
• Be sure to change the initial setting of the HDMI
1–4 input button on the remote so that you can use
the button to control your components. For details,
see “Programming the remote” (page 112).
• You can also rename the HDMI input so that it can
be displayed on the receiver’s display. For details,
see “Naming the input (Name Input)” (page 47).
28GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Notes on connecting cables
Notes on HDMI connections
• An audio signal input to the HDMI IN jack
is output from the SPEAKERS jacks, HDMI
TV OUT jack and PHONES jack. It is not
output from any other audio jacks.
• Video signals input to the HDMI IN jack can
only be output from the HDMI TV OUT
jack. The video input signals cannot be
output from the VIDEO OUT jacks or
MONITOR OUT jacks.
• The audio and video signals of HDMI input
are not output from the HDMI TV OUT jack
while the GUI menu is displayed.
• When you want to listen to the sound from
the TV speaker, set “Audio Out” to
“TV+AMP” in the HDMI Settings menu
(page 98). If you cannot play back multi
channel audio source, set to “AMP”.
However, the sound will not output from the
TV speaker.
• DSD signals of Super Audio CD are not
input and output.
• Be sure to turn on the receiver when the
video and audio signals of a playback
component are being output to a TV via the
receiver. If you set “Pass Through” to
“OFF”, video and audio signals will not be
transmitted when the power is turned off.
• Audio signals (sampling frequency, bit
length, etc.) transmitted from an HDMI jack
may be suppressed by the connected
component. Check the setup of the
connected component if the image is poor or
the sound does not come out of a component
connected via the HDMI cable.
• Sound may be interrupted when the
sampling frequency, the number of channels
or audio format of audio output signals from
the playback component is switched.
• When the connected component is not
compatible with copyright protection
technology (HDCP), the image and/or the
sound from the HDMI TV OUT jack may be
distorted or may not be output.
In this case, check the specification of the
connected component.
• You can enjoy High Bitrate Audio (DTS-HD
Master Audio, Dolby TrueHD), multi
channel Linear PCM only with an HDMI
connection.
• Set the image resolution of the playback
component to more than 720p/1080i to
enjoy High Bitrate Audio (DTS-HD Master
Audio, Dolby TrueHD).
• The image resolution of playback
component may need certain settings be
made before you can enjoy multi channel
Linear PCM. Refer to the operating
instructions of the playback component.
• To enjoy 3D images, connect 3D-compatible
TV and video components (Blu-ray disc
player, Blu-ray disc recorder, “PlayStation
3”, etc.) to the receiver using High Speed
HDMI cables, put on 3D glasses, and then
play back a 3D-compatible content.
• Depending on the TV or the video
component, 3D images may not be
displayed. Check the 3D image formats
supported by the receiver (page 131).
• Not every HDMI component supports all
functions that are defined by the specified
HDMI version. For example, components
that support HDMI, version 1.4, may not
support Audio Return Channel (ARC).
• Refer to the operating instructions of each
connected component for details.
29GB
STR-DN1010
4-174-068-11(1)
Connections
• Use a High Speed HDMI cable. If you use a
Standard HDMI cable, 1080p, Deep Color
(Deep Colour) or 3D images may not be
displayed properly.
• We do not recommend using an HDMI-DVI
conversion cable. When you connect an
HDMI-DVI conversion cable to a DVI-D
component, the sound and/or the image may
not be output. Connect other audio cords or
digital connecting cords, then set “Input
Assign” in the Input Option menu when the
sound is not output correctly.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
Connecting a Blu-ray disc player
The following illustration shows how to connect a Blu-ray disc player.
Blu-ray disc player
Video signals
A
Audio signals
B
C
A Component video cord (not supplied)
B Video cord (not supplied)
C Audio cord (not supplied)
D Optical digital cord (not supplied)
E Coaxial digital cord (not supplied)
D
E*
Recommended connection
Alternative connection
* When you connect a component equipped with an
COAXIAL jack, set “Input Assign” in the Input
Option menu (page 85).
Notes
• The initial setting of the COMPONENT VIDEO
IN 1 jacks are Blu-ray disc player. If you want to
connect your Blu-ray disc player to the
COMPONENT VIDEO IN 2 or IN 3 jacks, set
“Input Assign” in the Input Option menu (page 85).
• To input multi channel digital audio from the
Blu-ray disc player, set the digital audio output
setting on the Blu-ray disc player. Refer to the
operating instructions supplied with the Blu-ray
disc player.
30GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
Connecting a DVD player, DVD recorder
Connections
The following illustration shows how to connect a DVD player or DVD recorder.
DVD player, DVD recorder
Video signals
A
Audio signals
B*
A Component video cord (not supplied)
B Optical digital cord (not supplied)
C Coaxial digital cord (not supplied)
C
Recommended connection
Alternative connection
* When you connect a component equipped with an
OPTICAL jack, set “Input Assign” in the Input
Option menu.
Notes
• The initial setting for the DVD input button is as
follows:
– RM-AAP051: DVD player
– RM-AAP052: DVD recorder
To control other components, be sure to change the
initial setting of the DVD input button on the
remote. For details, see “Programming the remote”
(page 112).
• You can also rename the DVD input so that it can
be displayed on the receiver’s display. For details,
see “Naming the input (Name Input)” (page 47).
• The initial setting of the COMPONENT VIDEO
IN 2 jacks are DVD player or DVD recorder.
If you want to connect your DVD player or DVD
recorder to the COMPONENT VIDEO IN 1 or IN
3 jacks, set “Input Assign” in the Input Option
menu (page 85).
• To input multi channel digital audio from the DVD
player or DVD recorder, set the digital audio
output setting on the DVD player or DVD recorder.
Refer to the operating instructions supplied with
the DVD player or DVD recorder.
31GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
Connecting a satellite tuner, cable TV tuner
The following illustration shows how to connect a satellite tuner or cable TV tuner.
Satellite tuner, Cable TV tuner
Video signals
A
Audio signals
B
C
D
A Component video cord (not supplied)
B Video cord (not supplied)
C Audio cord (not supplied)
D Optical digital cord (not supplied)
Recommended connection
Alternative connection
Note
The initial setting of the COMPONENT VIDEO IN
3 jacks are satellite tuner or cable TV tuner. If you
want to connect your satellite tuner or cable TV
tuner to the COMPONENT VIDEO IN 1 or IN 2
jacks, set “Input Assign” in the Input Option menu
(page 85).
32GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
Connecting components with analog video and audio jack
DVD recorder, VCR
Audio signals
A
Video signals
B
(On the front panel)
Camcorder,
video game
C
A Audio cord (not supplied)
B Video cord (not supplied)
C Audio/video cord (not supplied)
Notes
• Be sure to change the initial setting of the VIDEO
1 input button on the remote so that you can use the
button to control your DVD recorder. For details,
see “Programming the remote” (page 112).
• You can also rename the VIDEO 1 input so that it
can be displayed on the TV screen and display. For
details, see “Naming the input (Name Input)”
(page 47).
continued
33GB
STR-DN1010
4-174-068-11(1)
Connections
The following illustration shows how to connect a component which has analog jacks such as a
DVD recorder, VCR, etc.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
Function for conversion of video signals
This receiver is equipped with a function for converting video signals.
Video signals and component video signals can be output as HDMI video signals (HDMI TV OUT
jack only).
INPUT jack
OUTPUT jack
HDMI IN
HDMI TV OUT
COMPONENT VIDEO IN
COMPONENT VIDEO MONITOR OUT
VIDEO IN
MONITOR VIDEO OUT
: Same type of signal as that of the input signal is output.
: Video signals are upconverted and output.
As the initial setting, video signals input from the connected component are output as shown in the
table above. We recommend that you set the video conversion function to match the resolution of
the monitor you are using. For details, see “Video Settings menu” (page 97).
Notes on converting video
signals
• When video signals from a VCR, etc., are
converted on this receiver and then output to
your TV, depending on the status of the
video signal output, the image on the TV
screen may appear distorted horizontally or
no image may be output.
• HDMI video signals cannot be converted to
component video signals and video signals.
• The converted video signals are not output
from the MONITOR VIDEO OUT and
COMPONENT VIDEO MONITOR OUT
jack.
• When you play back a VCR with an image
improvement circuit, such as TBC, the
images may be distorted or may not be
output. In this case, set the image
improvement circuit function to off.
• The resolution of the signals output to the
HDMI TV OUT jacks are converted up to
1080p.
• COMPONENT VIDEO MONITOR OUT
jacks have restrictions on resolution when
the resolution of video signals protected by
copyright technology is converted.
Resolution of up to 480p can be output to the
COMPONENT VIDEO MONITOR OUT
jacks. The HDMI TV OUT jack has no
restriction on resolution.
• Converted HDMI image output does not
support x.v.Color (x.v.Colour), Deep Color
(Deep Colour) and 3D image.
To connect a recording
component
When recording, connect the recording
component to the VIDEO OUT jacks of the
receiver. Connect cords for input and output
signals to the same type of jack, as VIDEO
OUT jacks do not have an up-conversion
function.
Note
Signals output from the HDMI TV OUT or
MONITOR OUT jacks may not be recorded
properly.
34GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
6: Inserting the wireless
transmitter/transceiver
Connect the supplied AM loop antenna
(aerial) and FM wire antenna (aerial).
Before connecting the antennas (aerials), be
sure to disconnect the AC power cord (mains
lead).
To use the S-AIR function, you need to insert
the wireless transmitter (not supplied) into the
S-AIR main unit and the wireless transceiver
(not supplied) into the S-AIR sub unit.
FM wire antenna (aerial) (supplied)
AM loop antenna (aerial)
(supplied)
Notes
• Before inserting the wireless transmitter/
transceiver, be sure to disconnect the AC power
cord (mains lead).
• Do not touch the terminals of the wireless
transmitter/transceiver.
To insert the wireless
transmitter into the S-AIR main
unit
1 Remove the screws.
Notes
• To prevent noise pickup, keep the AM loop
antenna (aerial) away from the receiver and other
components.
• Be sure to fully extend the FM wire antenna
(aerial).
• After connecting the FM wire antenna (aerial),
keep it as horizontal as possible.
Note
Remove the screws pointed with
not remove other screws.
mark. Do
continued
35GB
STR-DN1010
4-174-068-11(1)
Connections
5: Connecting the
antennas (aerials)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
2 Insert the wireless transmitter.
EZW-T100 slot
7: Connecting the AC
power cord (mains lead)
Connect the AC power cord (mains lead) to a
wall outlet.
Notes
Wireless transmitter
Notes
• Before connecting the AC power cord (mains
lead), make sure that metallic wires of the speaker
cords are not touching each other between the
SPEAKERS terminals.
• Connect the AC power cord (mains lead) firmly.
AC power cord (mains lead)
• Insert the wireless transmitter with the S-AIR
logo facing up.
• Insert the wireless transmitter so that the V
marks are aligned.
• Do not insert other than the wireless
transmitter into the EZW-T100 slot.
3 Use the screws that you removed from
step 1 to fasten the wireless
transmitter.
To the wall outlet
Note
Do not use other screws to fasten the wireless
transmitter.
To insert the wireless
transceiver into the S-AIR sub
unit
Refer to the operating instructions supplied
with the surround amplifier and S-AIR
receiver.
36GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Preparing the Receiver
Initializing the receiver
Selecting the front
speaker system
You can select the front speakers you want to
drive.
Be sure to use the buttons on the receiver for
this operation.
SPEAKERS
?/1
Press SPEAKERS repeatedly to
select the front speaker system
you want to drive.
1
Press ?/1 to turn off the
receiver.
2
Hold down ?/1 for 5 seconds.
After “CLEARING” appears on the
display for a while, “CLEARED!”
appears.
All the settings you have changed or
adjusted are reset to the initial settings.
To select the front speakers
connected to
Light up
The SPEAKERS FRONT A
terminals
SP A
The SPEAKERS SURROUND
BACK/FRONT HIGH/BI-AMP/
FRONT B terminals
SP B*
Both the SPEAKERS FRONT A and SP A B*
SPEAKERS SURROUND BACK/
FRONT HIGH/BI-AMP/FRONT B
terminals (parallel connection)
* To select “SP B” or “SP A B”, set “SB Assign” to
“Speaker B” in the Speaker Settings menu
(page 91).
To turn off the speaker output
Press SPEAKERS repeatedly until the “SP A”
and “SP B” indicators on the display do not
light up. “SPK OFF” appears on the display.
Note
You cannot switch the front speaker system by
pressing SPEAKERS when the headphones are
connected.
37GB
STR-DN1010
4-174-068-11(1)
Preparing the Receiver
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their initial settings.
Be sure to use the buttons on the receiver for
this operation.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Calibrating the
appropriate speaker
settings automatically
(Auto Calibration)
This receiver is equipped with DCAC (Digital
Cinema Auto Calibration) function which
allows you to perform automatic calibration as
follows:
• Check the connection between each speaker
and the receiver.a)
• Adjust the speaker level.
• Measure the distance of each speaker from
your listening position.a)b)
• Measure the speaker size.a)
• Measure the speaker polarity.
• Measure the frequency characteristics.a)c)
a)
The measurement result is not utilized when
“Analog Direct” is selected.
b) The measurement result is not utilized when
signals with a sampling frequency of more than
96 kHz are being received.
c) The measurement result is not utilized when
signals with a sampling frequency of more than
48 kHz are being received.
The DCAC is designed to obtain proper sound
balance in your room. However, you can
adjust the speaker levels and balance manually
according to your preference. For details, see
“Test Tone” (page 93).
masterpage: Left
Before you perform Auto
Calibration
Before you perform Auto Calibration, check
the following items.
• Set up and connect the speakers
(page 19–21).
• Connect only the supplied optimizer
microphone to the AUTO CAL MIC jack.
Do not connect other microphones to this
jack.
• Set “SB Assign” to “BI-AMP” in the
Speaker Settings menu if you use
bi-amplifier connection (page 91).
• Set “SB Assign” to “Speaker B” in the
Speaker Settings menu if you use speakers
front B connection (page 91).
• Pair the surround amplifier to S-AIR main
unit if you want to use surround amplifier.
• Make sure the speaker output is not set to
“SPK OFF” (page 37).
• Disconnect the headphones.
• Remove any obstacles in the path between
the optimizer microphone and the speakers
to avoid measurement errors.
• Make sure the environment is quiet to avoid
the effect of noise and get a more accurate
measurement.
• Select the seating position as position 1, 2 or
3 to save the Auto Calibration result
(page 90).
Notes
• During the measurement, the sound that comes out
of the speakers is very loud. The volume of the
sound cannot be adjusted. Pay attention to the
presence of children or to the effect on your
neighborhood.
• If the muting function has been activated before
you perform Auto Calibration, the muting function
will be set to off automatically.
38GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
1: Setting up the Auto
Calibration
On setting up the active
subwoofer
• When a subwoofer is connected, turn on the
subwoofer and turn up the volume
beforehand. Turn the MASTER VOLUME
to just before the mid-point.
• If you connect a subwoofer with a crossover
frequency function, set the value to
maximum.
• If you connect a subwoofer with an auto
standby function, set it to off (deactivated).
Optimizer
microphone
When using front high
speakers*
Note
Depending on the characteristics of the subwoofer
you are using, the setup distance value may be
further away from the actual position.
* Be sure to set the speaker pattern setting with front
high speakers (page 91).
1
Connect the supplied optimizer
microphone to the AUTO CAL
MIC jack.
2
Set up the optimizer
microphone.
Place the optimizer microphone at your
listening position. Use a stool or tripod so
that the optimizer microphone remains at
the same height as your ears.
39GB
STR-DN1010
4-174-068-11(1)
Preparing the Receiver
When using surround back
speakers
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
2: Performing Auto Calibration
?/1
masterpage: Left
4
Press V/v repeatedly to select
“Auto Cal. Start”, then press
or b.
5
6
Press
to select “START”.
The measurement starts in five
seconds.
Input
buttons
Auto Calibration
Count Down
Please press enter key
to stop.
5
CANCEL
RETURN
GUI
MODE
V/v/b,
MENU
7
Measurement starts.
The measurement process will take
approximately 30 seconds with a test
tone. Wait until the measurement process
completes.
Auto Calibration
MUTING/
MASTER
VOL +/–/
2 +/–
TONE
1
WOOFER
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
T.S.P.
Press V/v repeatedly to select
“Settings”, then press
or b.
Tips
• Operations other than turning the receiver on or off
are deactivated during the measurement.
• The measurements may not be performed correctly
or Auto Calibration cannot be performed when
special speakers, such as dipole speakers are used.
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“Auto Cal.”, then press
or b.
40GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
To cancel Auto Calibration
2
Press V/v repeatedly to select the item
you want, then press .
Item and explanation
Retry
Performs the Auto Calibration again.
Save
Saves the measurement results and exits the
setting process.
Warning
Displays warning concerning the
measurement results. See “Message list after
Auto Calibration measurement” (page 43).
Phase*
Displays the phase of each speaker (in phase/
out of phase).
3: Confirming/saving the
measurement results
1
View the measurement result.
Distance
Displays the measurement result for speaker
distance.
Confirm the measurement
result.
Level
Displays the measurement result for speaker
level.
When the measurement ends, a beep
sounds.
Exit
Exits the setting process without saving the
measurement results.
Auto Calibration
* When the speaker(s) is (are) out of the phase,
“OUT” is displayed on the TV screen. The
“+” and “–” terminals of the speaker may be
connected the other way around.
However, depending on the speakers, “OUT”
appears on the TV screen even though the
speakers are connected properly. This is
because of the speakers’ specifications. In
this case, you can continue to use the
receiver.
Save
Note
If an error code appears on the screen, see
“Message list after Auto Calibration
measurement” (page 43).
3
Save the measurement result.
Select “Save” in step 2.
continued
41GB
STR-DN1010
4-174-068-11(1)
Preparing the Receiver
The Auto Calibration function will be
canceled when you do the following during the
measurement process:
– Press ?/1.
– Press the input buttons on the remote or
press the INPUT SELECTOR +/–
repeatedly on the receiver.
– Press MUTING (RM-AAP051 only) or
(RM-AAP052 only) on the remote. You can
also use MUTING on the receiver.
– Press SPEAKERS on the receiver.
– Change the volume level.
– Connect the headphones.
– Press .
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
4
masterpage: Left
Select the Auto Calibration
Type.
Press V/v repeatedly to select “Auto Cal.
Type”, then press .
Auto Calibration
Auto Cal. Type
Full Flat
Engineer
Front Reference
Off
RETURN
Calibration type and explanation
Full Flat
Makes the measurement of frequency from
each speaker flat.
Engineer
Sets the frequency to one that matches that of
the Sony listening room standard.
Front Reference
Adjusts the characteristics of all the speakers
to match the characteristics of the front
speaker.
Off
Sets the Auto Calibration to off.
5
Disconnect the optimizer
microphone after you have
finished.
Note
If you have reposition your speaker, we recommend
that you perform Auto Calibration again to enjoy the
surround sound.
Tip
The size of a speaker (“Large”/“Small”) is
determined by the low frequency characteristics.
The measurement results may vary, depending on
the position of the optimizer microphone and
speakers, and the shape of the room. It is
recommended that you follow the measurement
results. However, you can change those settings in
the Speaker Settings menu. Save the measurement
results first, then try to change the settings if you
want.
42GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
Message list after Auto Calibration measurement
Display and explanation
Error Code 31
The SPEAKERS is set to off. Set it to others and perform the Auto Calibration again.
Error Code 33
• None of the front speakers are connected or only one front speaker is connected.
• The optimizer microphone is not connected.
• Either the surround left or surround right speaker is not connected.
• Surround back speakers or front high speakers are connected even though surround speakers are not
connected. Connect the surround speaker(s) to the SPEAKERS SURROUND terminals.
• The surround back speaker is connected only to the SPEAKERS SURROUND BACK/FRONT HIGH/
BI-AMP/FRONT B R terminals. When you connect only one surround back speaker, connect it to the
SPEAKERS SURROUND BACK/FRONT HIGH/BI-AMP/FRONT B L terminals.
• Either the front left high or front right high speaker is not connected.
Warning 40
The measurement has completed. However, the noise level is high. You may be able to perform the
measurement properly if you try it again, even though the measurement cannot be performed in all
environments. Try to perform the measurement in a quiet environment.
Warning 41
The sound input from the optimizer microphone is outside the acceptable range. It is louder than the loudest
sound that can be measured. Try to perform the measurement when the environment is quiet enough to allow
proper measurement.
Warning 42
The volume of the receiver is out of the acceptable range. Try to perform the measurement when the
environment is quiet enough to allow proper measurement.
Warning 43
The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try to perform the
measurement in a quiet environment.
NO WARNING
There is no warning information.
When “Error Code” appears
When “Warning” appears
Check the error and perform Auto Calibration
again.
1 When you press , “RETRY?” appears.
2 Press B/b to select “YES”.
3 Press .
The measurement starts in five seconds.
If a warning on the measurement result is
present, detailed information is displayed.
Press
to return to step 1 of “3: Confirming/
saving the measurement results” (page 41).
Tip
Depending on the position of the subwoofer, the
measurement results for polarity may vary.
However, there will be no problems even if you
continue to use the receiver with that value.
43GB
STR-DN1010
4-174-068-11(1)
Preparing the Receiver
Error Code 32
None of the speakers were detected. Make sure that the optimizer microphone is connected properly and
perform the measurement again.
If the optimizer microphone is connected properly but the error code appears, the optimizer microphone cable
may be damaged or improperly connected.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
2
Guide to on-screen
display operation
masterpage: Left
Press V/v repeatedly to select a
menu you want, then press
.
The menu item list appears on the TV
screen.
Example: When you select “Settings”.
You can display the menu of the receiver on
the TV screen and select the function you want
to use on the TV screen by pressing V/v/B/b
and
on the remote.
To display the menu of the receiver on the TV
screen, make sure that the receiver is in “GUI
MODE” following the steps in “To turn “GUI
MODE” on and off” (page 44).
Auto Cal.
Speaker
Surround
EQ
Settings
Audio
GUI MODE
V/v/B/b,
RETURN/
EXIT O
Press V/v repeatedly to select
the menu item you want to
adjust, then press
to enter
the menu item.
4
Repeat steps 2 and 3 to select
the parameter you want.
TOOLS/
OPTIONS
MENU
Using the menu
1
3
To return to the previous screen
Press RETURN/EXIT O.
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
To exit the menu
Press MENU.
To turn “GUI MODE” on and off
Press GUI MODE. “MENU ON” or “MENU
OFF” appears on the display, depending on the
mode selected.
BD
Input
DVD
SAT/CATV
Music
TV
Video
VIDEO 1
44GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Overview of the main menus
Menu icon
2
Description
Input
Selects the input source
component connected to the
receiver (page 46).
The menu item list appears on the TV
screen.
Example: when you select “Input”.
Selects the music from the
audio component connected
to the DIGITAL MEDIA
PORT adapter (page 48).
Video
BD
Selects the images from the
video components connected
to the DIGITAL MEDIA
PORT adapter (page 48).
FM/AM/SR
Press V/v repeatedly to select a
menu you want, then press
or b to enter the menu.
Input
TV
Selects the built-in FM/AM
radio or satellite tuner
connected (page 53, 57).
Settings
You can adjust the settings of
the speakers, the surround
effect, equalizer, audio,
video and other inputs
connected to the HDMI jacks
(page 89).
VIDEO 1
3
Press TOOLS/OPTIONS while
the menu item list is displayed.
The option menu appears.
Using the option menus
BD
Input
When you press TOOLS/OPTIONS, the
option menus for the selected main menu are
displayed. You can select a related function
without reselecting the menu.
1
DVD
SAT/CATV
DVD
SAT/CATV
Input Assign
Name lnput
TV
VIDEO 1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
BD
Input
Press V/v repeatedly to select
the option menu item you want,
then press
or b.
5
Press V/v repeatedly to select
the parameter you want, then
press
.
DVD
SAT/CATV
To exit the menu
TV
Press MENU.
Music
Video
4
VIDEO 1
45GB
STR-DN1010
4-174-068-11(1)
Preparing the Receiver
Music
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
3
Basic Operations
Playback
masterpage: Left
Press V/v repeatedly to select
the component you want, then
press
.
The selected input appears on the TV
screen.
4
Turn on the component and
start playback.
5
Press MASTER VOL +/–
(RM-AAP051 only) or 2 +/–
(RM-AAP052 only) to adjust the
volume.
?/1
Input
buttons
You can also use MASTER VOLUME on
the receiver.
6
GUI MODE
V/v/B/b,
RETURN/
EXIT O
TOOLS/
OPTIONS
MENU
MUTING/
1
MASTER
VOL +/–/
2 +/–
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press SOUND FIELD +/– to
enjoy the surround sound.
You can also use 2CH/A.DIRECT,
A.F.D., MOVIE, MUSIC button on the
receiver.
For details, see page 65.
Tips
• You can press INPUT SELECTOR +/– on the
receiver repeatedly or press input buttons on the
remote to select the component you want.
• You can adjust the volume differently depending
on the speed with which you turn the MASTER
VOLUME on the receiver.
To turn the volume up or down quickly: turn the
knob quickly.
To make fine adjustment: turn the knob slowly.
• You can adjust the volume differently depending
on the length of time you press and hold the
MASTER VOL +/– (RM-AAP051 only) or
2 +/– (RM-AAP052 only) button on the remote.
To turn the volume up or down quickly: press and
hold the button.
To make a fine adjustment: press the button and
release it immediately.
Press V/v repeatedly to select
“Input”, then press
or b.
The menu item list appears on the TV
screen.
46GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
To activate the muting function
To cancel naming input
Press MUTING (RM-AAP051 only) or
(RM-AAP052 only) on the remote.
You can also use MUTING on the receiver.
The muting function will be canceled when
you do the following.
• Press MUTING (RM-AAP051 only) or
(RM-AAP052 only) again.
• Increase the volume.
• Turn off the receiver.
• Perform Auto Calibration.
Press RETURN/EXIT O.
Viewing information on the
display
You can check the sound field, etc., by
changing the information on the display.
Basic Operations
To avoid damaging your
speakers
AMP
Before you turn off the receiver, be sure to turn
down the volume level.
Naming the input (Name Input)
You can enter a name of up to 8 characters for
inputs and display it.
This is convenient for labeling the jacks with
the names of the connected components.
1
2
Press V/v repeatedly on the
“Input” screen to select the
input you want.
Press TOOLS/OPTIONS.
The option menu appears.
3
Press V/v repeatedly to select
“Name Input”, then press
.
BD
Input
DVD
SAT/CATV
Input Assign
Name lnput
TV
DISPLAY
Press AMP, then press DISPLAY
repeatedly.
You can also use DISPLAY on the receiver.
Each time you press DISPLAY, the display
will change as follows.
Input name you selecteda) t Original input
name t Sound field currently applied t
Volume level t Stream information
FM and AM band
Program Service nameb) or preset station
namea) t Frequency t Program Type
indicationb) t Radio Text indicationb) t
Current Time indication (in 24-hour system
mode)b) t Sound field currently applied t
Volume level
VIDEO 1
4
Press V/v/B/b to select a
character, then press
.
The name you entered is registered.
continued
47GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
SIRIUS Satellite Radio (Models
of area code U2, CA2 only)
Channel name t Channel number t
Category name t Artist name/Feature t
Song/program title t Composer name t
Signal strength t Sound field type t
Volume level
a)
Index name appears only when you have assigned
one to the input or preset station (page 56). Index
name does not appear when only blank spaces
have been entered or it is the same as the input
name.
b) During RDS reception only (Models of area code
CEK, ECE, AU1, TW2 only) (page 56).
masterpage: Left
Enjoying sound/images
from the components
connected to the DIGITAL
MEDIA PORT
The DIGITAL MEDIA PORT (DMPORT)
allows you to enjoy picture and sound from a
network system such as a portable audio/video
source or computer.
For details on connecting the DIGITAL
MEDIA PORT adapter, see “Connecting
audio components” (page 24).
Note
Character or marks may not be displayed for some
languages.
Tip
You cannot switch the display while “GUI” is shown
on the display. Press GUI MODE repeatedly to
select “MENU OFF”.
You can use the following Sony DIGITAL
MEDIA PORT adapters:
• TDM-BT1/BT10 Bluetooth™ Wireless
Audio Adapter
• TDM-NW10 DIGITAL MEDIA PORT
Adapter
• TDM-NC1 Wireless Network Audio Client
• TDM-iP10/iP50 DIGITAL MEDIA PORT
Adapter
• TDM-MP10 DIGITAL MEDIA PORT
Adapter
The DIGITAL MEDIA PORT adapter is an
optional product.
Notes
• Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter to the DMPORT jack.
• Before disconnecting the DIGITAL MEDIA
PORT adapter, be sure to turn off the receiver.
• Do not connect or disconnect the DIGITAL
MEDIA PORT adapter while the receiver is turned
on.
• Depending on the type of DIGITAL MEDIA
PORT adapter, video output may not be possible.
• The DIGITAL MEDIA PORT adapters are
available for purchase depending on the area.
48GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
If the option menu does not appear on the
screen, refer to the operating instructions
of the connected component.
When an adapter other than iPod is
connected, a hierarchical menu does not
appear.
Selecting the operation screen
You can select an operation screen using the
GUI menu, depending on the DIGITAL
MEDIA PORT adapter you want to use. For
some adapter, such as TDM-BT1, the
operation screen is fixed and you cannot
change it on the GUI screen.
Operating the component
connected to the DIGITAL MEDIA
PORT adapter
V/v/b,
TOOLS/
OPTIONS
V/v/B/b,
MENU
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“Music” or “Video”, then press
or b.
3
Press TOOLS/OPTIONS.
The option menu appears.
4
Press V/v repeatedly to select
the mode you want, then press
.
The details of each mode are as follows:
• System GUI
This mode is for the TDM-iP50 and
TDM-NC1. The list of tracks will be
displayed on the GUI screen of the
receiver. You can select a track you
want and play it back on each GUI
screen.
• iPod
This mode is for the TDM-iP50.
To operate the TDM-iP50 or
TDM-NC1 using the GUI menu of
the receiver
1
Make sure that “System GUI” is
selected in step 4 in “Selecting
the operation screen”
(page 49).
2
Press V/v/B/b repeatedly to
select the content you want
from the contents list displayed
on the GUI screen, then press
to play it back.
The following content lists are just
examples. They may vary depending on
the components connected to the receiver.
continued
49GB
STR-DN1010
4-174-068-11(1)
Basic Operations
GUI MODE
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Contents list for audio
iPod
Playlists > Playlist > Track
Artists > Artist > Album > Track
Albums > Album > Track
Songs > Track
masterpage: Left
Playing the selected track
During playback of the selected track, the
displayed screen changes depending on the
DIGITAL MEDIA PORT adapter connected.
Genres > Genre > Artist > Album > Track
Example of a “System GUI” screen
Composers > Composer > Track
Music Player
Audiobooks > Audiobook > Track
1/1
0:17
Network Client
Music Surfina) > Albumc) > Track
Playlista) > Playlist > Track
Title Sample
Artist Sampl...
Album Sample
Web Radioa) > Station > Program
Music Libraryb) > Album > Track
RETURN
OPTIONS
a)
Displayed only when M-crew Server is connected.
b)
Displayed only when a DLNA server other than
M-crew Server is connected.
c)
Displayed as “Genre”, “Artist” or “Album”,
depending on setting of “List Mode”.
You can operate the components connected to
the DIGITAL MEDIA PORT adapter using
the following buttons on the remote of the
receiver.
Contents list for video
iPod
./>
Movies > Content
B•/•b
TV Shows > Episode > Content
m/M
N
Music Videos > Artist > Content
x
Video Playlists > Video Playlist > Content
X
Video Podcasts > Episode > Content
3
Press MASTER VOL +/–
(RM-AAP051 only) or 2 +/–
(RM-AAP052 only) to adjust the
volume.
To operate the TDM-iP50 using
the iPod menu
Make sure that “iPod” is selected in step 4 in
“Selecting the operation screen” (page 49).
For details on operating the iPod, refer to the
operating instructions supplied with the iPod.
To
Do the following
Play
Press N.
Pause
Press X. To resume play,
press the button again.
Stop
Press x.
Find the beginning of a Press ..
track during playback, or
find the beginning of the
previous track
Find the beginning of the Press >.
next track
Skip to the previous/next Press B•/•b.
album
Go backward/forward
Press m/M.*
* Fast-backward/forward while pressing and
holding the m/M button.
50GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Selecting the playback mode
1
Press TOOLS/OPTIONS.
The option menu appears.
3
4
Press V/v repeatedly to select
“Repeat”, “Shuffle”, “List
Mode” or “Audiobook”, then
press
or b.
Press V/v repeatedly to select
the mode you want to select
from the following, then press
.
x Repeat (TDM-iP50 only)
• OFF
• One
• All
x Shuffle (TDM-iP50 only)
DIGITAL MEDIA PORT message
list
Message and explanation
No Adapter
The adapter is not connected.
No Device
There is no device connected to the adapter.
No Audio
No audio file was found.
Basic Operations
2
Play back the track you want to
listen to following the steps in
“Operating the component
connected to the DIGITAL
MEDIA PORT adapter”
(page 49).
masterpage: Right
Loading
The data is being read.
No Server*
There is no server connected.
No Track*
No track was found.
No Item
No item was found.
Connecting*
Connecting to the server.
Configuring*
The network is setting up.
Warning*
Check the display of the DIGITAL MEDIA PORT
adapter.
Searching*
Searching the server.
* TDM-NC1 only.
• OFF
• Songs
• Albums
x List Mode (TDM-NC1 only)
•
•
•
•
All Tracks
Disc List
Artist List
Genre List
x Audiobook (TDM-iP50 only)
• Low
• Normal
• High
51GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Using the Sleep Timer
You can set the receiver to turn off
automatically at a specified time.
AMP
masterpage: Left
Recording using the
receiver
You can record from a video/audio component
using the receiver. Refer to the operating
instructions supplied with your recording
component.
Recording onto a CD-R
You can record onto a CD-R using the
receiver. Refer to the operating instructions
supplied with your CD recorder.
1
Press one of the input buttons
to select the playback
component.
You can also use INPUT SELECTOR +/–
on the receiver.
2
Prepare the playback
component for playing.
For example, tune to the radio station you
want to record (page 53).
3
Prepare the recording
component.
Insert a blank CD-R into the CD recorder
and adjust the recording level.
SLEEP
Press AMP, then press SLEEP
repeatedly while the power is on.
“SLEEP” lights up on the display.
Each time you press the button, the display
changes cyclically as follows:
4
Start recording on the
recording component, then
start playback on the playback
component.
Note
Sound adjustments do not affect the signal output
from the SA-CD/CD/CD-R AUDIO OUT jacks.
0:30:00 t 1:00:00 t 1:30:00 t 2:00:00
t OFF
Tip
To check the remaining time before the receiver
turns off, press SLEEP. The remaining time appears
on the display. If you press SLEEP again, the Sleep
Timer will be canceled.
52GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Recording onto a recording
media
1
2
Listening to FM/AM radio
You can also use INPUT SELECTOR
+/– on the receiver.
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and
AM antennas (aerials) to the receiver (page
35).
Prepare the playback
component for playing.
Prepare the recording
component.
Tip
The tuning scale for direct tuning differs depending
on the area code as shown in the following table. For
details on area codes, see page 4.
Insert a blank video tape, etc. into the
recording component (connected to
VIDEO 1 OUT jacks) for recording.
Area code
FM
U2, CA2
100 kHz
Start recording on the
recording component, then
start playback on the playback
component.
* The AM tuning scale can be changed (page 55).
Notes
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to
record from the source.
• Only analog input signals are output from the
analog output jack (for recording).
• HDMI sound cannot be recorded.
CEK, ECE, AU1, TW2 50 kHz
AM
10 kHz*
9 kHz
SHIFT
Numeric
buttons
GUI MODE
V/v/b,
TOOLS/
OPTIONS
MENU
53GB
STR-DN1010
4-174-068-11(1)
Tuner Operations
4
Tuner Operations
Press the input button of the
playback component.
For example, insert the video tape you
want to copy into the VCR.
3
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Tuning into a station
automatically (Auto Tuning)
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“FM” or “AM”, then press
or
b.
Tuning into a station directly
(Direct Tuning)
You can enter the frequency of a station
directly by using the numeric buttons.
1
4
Press V/v repeatedly to select
“Auto Tuning”, then press
or b.
2
3
Press V/v repeatedly to select
“Direct Tuning”, then press
or b.
4
Press SHIFT, then press
numeric buttons to enter the
frequency.
Example 1: FM 102.50 MHz
Select 1 b 0 b 2 b 5 (b 0*)
Example 2: AM 1,350 kHz
Select 1 b 3 b 5 b 0
In case of poor FM stereo
reception
1 Tune in the station you want to listen to
using Auto Tuning, Direct Tuning
(page 54), or select the preset station you
want (page 55).
2 Press TOOLS/OPTIONS.
3 Press V/v repeatedly to select “FM Mode”,
then press
or b.
4 Press V/v repeatedly to select “MONO”,
then press .
Press V/v repeatedly to select
“FM” or “AM”, then press
or
b.
The FM or AM menu list appears on the
TV screen.
Press V/v.
Press V to scan from low to high, press v
to scan from high to low.
The receiver stops scanning whenever a
station is received.
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
The FM or AM menu list appears on the
TV screen.
3
masterpage: Left
* Press 0 for models of area code CEK,
ECE, AU1, TW2 only.
Tip
If you have tuned in an AM station, adjust
the direction of the AM loop antenna
(aerial) for optimum reception.
5
Press
.
If you cannot tune in a station
“– – – .– – MHz” appears and then the screen
returns to the current frequency.
Make sure you have entered the right
frequency. If not, repeat step 4. If you still
cannot tune in a station, the frequency is not
used in your area.
54GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Changing the AM tuning scale
(Models of area code U2, CA2 only)
You can change the AM tuning scale to either
9 kHz or 10 kHz on the receiver.
?/1
masterpage: Right
Presetting FM/AM radio
stations (Preset Tuning)
You can preset up to 30 FM and 30 AM
stations. Then you can easily tune in the
stations you often listen to.
GUI MODE
V/v/b,
MENU
1
Press ?/1 to turn off the
receiver.
2
While holding down DISPLAY,
press ?/1 on the receiver.
3
Change the current AM tuning
scale to 9 kHz (or 10 kHz).
To reset the scale to 10 kHz (or 9 kHz),
repeat the procedure above.
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Note
All preset stations will be erased when you change
the tuning scale.
Press V/v repeatedly to select
“FM” or “AM”, then press
or
b.
The FM or AM menu list appears on the
TV screen.
3
Tune in the station that you
want to preset using Auto
Tuning (page 54) or Direct
Tuning (page 54).
In case of poor FM stereo reception,
switch the FM reception mode (page 54).
4
Press TOOLS/OPTIONS.
The option menu appears.
5
Press V/v repeatedly to select
“Memory”, then press
or b.
continued
55GB
STR-DN1010
4-174-068-11(1)
Tuner Operations
TOOLS/
OPTIONS
DISPLAY
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
6
Press V/v repeatedly to select a
preset number, then press
.
The station is stored as the selected preset
number.
7
Repeat steps 3 to 6 to preset
another station.
You can store station as follows:
• AM band: AM 1 to AM 30
• FM band: FM 1 to FM 30
Tuning to preset stations
Repeat steps 1 and 2 of
“Presetting FM/AM radio
stations (Preset Tuning)”.
2
Press V/v repeatedly to select
the preset station you want.
Preset numbers from 1 to 30 are available.
Naming preset stations (Name
Input)
2
Using the Radio Data
System (RDS)
(Models of area code CEK, ECE,
AU1, TW2 only)
This receiver allows you to use Radio Data
System (RDS), which enables radio stations to
send additional information along with the
regular program signal. This receiver offers
convenient RDS features, such as Program
Service name display.
Notes
1
1
masterpage: Left
On “FM” or “AM” screen, press
V/v repeatedly to select the
preset number on which you
have stored the station and
which you want to name.
Press TOOLS/OPTIONS.
The option menu appears.
3
Press V/v repeatedly to select
“Name Input”, then press
or
b.
4
Press V/v/B/b to select a
character, then press
.
• RDS is operable only for FM stations.
• Not all FM stations provide RDS service, nor do
they provide the same type of services. If you are
not familiar with the RDS services in your area,
check with your local radio stations for details.
Receiving RDS broadcasts
Simply select a station on the FM
band using Direct Tuning (page 54),
Auto Tuning (page 54), or Preset
Tuning (page 55).
When you tune in a station that provides RDS
services, “RDS” lights up and the program
service name appears on the display.
Note
RDS may not work properly if the station you tuned
to is not transmitting the RDS signal properly or if
the signal strength is weak.
Tip
When a Program Service name is displayed, you can
check the frequency by pressing DISPLAY
repeatedly (page 47).
The name you entered is registered.
56GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Listening to Satellite
Radio
(Models of area code U2, CA2 only)
To listen to Satellite Radio, you’ll need to
connect a SIRIUS Satellite Radio tuner (sold
separately) to your Sirius-Ready receiver.
SIRIUS Satellite Radio is available to
residents of the US (except Alaska and
Hawaii) and Canada.
masterpage: Right
SIRIUS and all related marks and logos are
trademarks of Sirius XM Radio Inc. and its
subsidiaries. All other marks and logos are the
property of their respective owners. All rights
reserved. SIRIUS subscription sold separately.
Taxes and a one-time activation fee may apply.
SIRIUS tuner required (sold separately) to receive
the SIRIUS service. All programming and fees
subject to change. It is prohibited to copy,
decompile, disassemble, reverse engineer, hack,
manipulate or otherwise make available any
technology or software incorporated in receivers
compatible with the SIRIUS Satellite Radio System.
Service not available in Alaska or Hawaii.
Tuner Operations
Satellite Radio delivers a variety of
commercial-free music from categories
ranging from Pop, Rock, Country, R&B,
Dance, Jazz, Classical and many more plus
coverage of all the top professional and
college sports including play by play games
from select leagues and teams. Additional
programming includes expert sports talk,
uncensored entertainment, comedy, family
programming, local traffic and weather and
news from your most trusted sources.
Once you’ve purchased a SIRIUS tuner you’ll
need to activate it and subscribe to begin
enjoying the service. Easy to follow
installation and setup instructions are provided
with the SIRIUS tuner. There are a variety of
programming packages available, including
the option of adding “The Best of XM”
programming to the SIRIUS service. The
“Best of XM” service is not available to
SIRIUS Canada subscribers at this time.
Please check with SIRIUS Canada for any
updates using the numbers and web address
below.
Family friendly packages are also available to
restrict channels featuring content that may be
inappropriate for children.
To subscribe to SIRIUS, U.S. and Canadian
customers can call 1-888-539-SIRI (1-888539-7474) or visit sirius.com (US) or
siriuscanada.ca (Canada).
57GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Connecting the SIRIUS
Satellite Radio
masterpage: Left
Preparing to listen to the
SIRIUS Satellite Radio
Connect the SiriusConnect Home tuner. When
you use the SiriusConnect Home tuner with
this receiver, be sure to connect the AC power
adaptor supplied with the tuner to a wall outlet.
GUI MODE
V/v/b,
SIRIUS jack
TOOLS/
OPTIONS
MENU
Checking the SIRIUS Radio ID
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Note
Keep the SiriusConnect Home tuner, antenna, and
AC power adaptor away from the speaker cords and
the power cord to avoid picking up noise.
2
Press V/v repeatedly to select
“SR”, then press
or b.
3
Press TOOLS/OPTIONS, then
press V/v repeatedly to select
“Sirius ID”, then press
or b.
4
Check the SIRIUS ID on the TV
screen and write it in the space
provided here.
ID:_________________________________
You can also check the SIRIUS ID using
the display on the receiver.
58GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Checking receiving conditions
(Antenna Aiming)
1
Press GUI MODE.
Selecting a channel of the
SIRIUS Satellite Radio
SHIFT
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Press V/v repeatedly to select
“SR”, then press
or b.
3
Press TOOLS/OPTIONS, then
press V/v repeatedly to select
“Antenna”, then press
or b.
4
Numeric
buttons
GUI MODE
V/v/b,
While checking the quality of
the reception, adjust the
direction of the antenna to
obtain the best reception.
TOOLS/
OPTIONS
MENU
To exit the menu
Press MENU.
Selecting a channel by category
(Category Mode)
You can select a channel from one category or
all the categories.
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“SR”, then press
or b.
continued
59GB
STR-DN1010
4-174-068-11(1)
Tuner Operations
2
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
3
Press V/v repeatedly to select
the category, then press
or
b.
• All: You can select a channel from all
the categories.
• (category name): You can select a
channel from one category.
Selecting a channel by inputting
the channel number directly
(Direct Tuning)
1
4
Press V/v repeatedly to select
the channel, then press
.
The selected channel is being received.
The channel information is displayed on
the TV screen.
2
Press V/v repeatedly to select
“SR”, then press
or b.
3
Press TOOLS/OPTIONS.
The option menu appears.
4
Press V/v repeatedly to select
“Direct Tuning”, then press
or b.
5
Press SHIFT, then press the
numeric buttons to enter the
channel number.
6
Press
Note
When you select a channel in the “Category Mode”,
the channel you selected may not be the one in the
category you want. This is because one channel may
belong to more than one category.
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Note
When the “Preset Mode” screen is displayed,
press TOOLS/OPTIONS, then press V/v
repeatedly to select “Category Mode”.
masterpage: Left
.
The selected channel is tuned in.
60GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Presetting SIRIUS
Satellite Radio channels
6
7
V/v/b,
Repeat steps 3 to 6 to preset
another channel.
Selecting the channel by using
the preset numbers
MENU
Presetting channels using the
preset numbers
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“SR”, then press
or b.
3
Select a channel you want to
preset using Category Tuning
(page 59) or Direct Tuning
(page 60).
4
Press TOOLS/OPTIONS.
1
Repeat steps 1 and 2 of
“Presetting channels using the
preset numbers” (page 61).
2
Press V/v repeatedly to select
the preset number from the
preset list, then press
.
You can select stored preset channels
from 1 to 30.
Notes
• The channel information you have preset may be
changed if SIRIUS Satellite Radio Inc. change
their channel programming.
• When the “Category Mode” screen is displayed,
press TOOLS/OPTIONS, then press V/v
repeatedly to select “Preset Mode”.
The option menu appears.
5
Press V/v repeatedly to select
“Memory”, then press
or b.
61GB
STR-DN1010
4-174-068-11(1)
Tuner Operations
TOOLS/
OPTIONS
Press V/v repeatedly to select
the preset channel you want,
then press
.
Preset channels from 1 to 30 are available,
and a default channel is preset for all the
preset channels when you purchase the
receiver.
The selected channel is registered as the
preset channel you selected in step 3.
You can select the channels you want directly
by presetting them using the preset numbers.
You can preset up to 30 SIRIUS Satellite
Radio channels.
GUI MODE
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
Restricting access to
specific channels
4
You can restrict access to certain channels
using your own lock code. The lock code is set
to “0000” as the default.
Change the lock code before you use this
function for the first time. See “To change the
lock code (Lock Code)” (page 62).
SHIFT
Numeric
buttons
Press V/v repeatedly to select
“ON”, then press
.
“Enter your 4-digit lock code.” appears.
5
(Parental Lock)
masterpage: Left
Press SHIFT, then press the
numeric buttons to enter your
4-digit lock code.
“The channel has been locked.” appears
and the Parental Lock is set.
To delete the numbers you have entered,
go back to step 2 by pressing RETURN/
EXIT O, and then repeat the procedure
above from step 2.
To change the lock code (Lock
Code)
1 Select a channel you want to change
the lock code using Category Mode
(page 59) or Direct Tuning (page 60).
2 Press TOOLS/OPTIONS.
The option menu appears.
3 Press V/v repeatedly to select “Lock
V/v/b,
RETURN/
EXIT O
TOOLS/
OPTIONS
Code”, then press
.
“Enter your 4-digit lock code.” appears.
4 Press SHIFT, then press the numeric
buttons to enter your 4-digit lock code.
“Enter a new lock code.” appears.
5 Enter a new 4-digit lock code using the
1
2
Select a channel you want to
lock using Category Mode
(page 59) or Direct Tuning
(page 60).
Press TOOLS/OPTIONS.
numeric buttons.
“To confirm, enter your new lock code
again.” appears.
6 Reenter the new lock code with the
numeric buttons.
“The lock code has been changed.”
appears.
The option menu appears.
3
Press V/v repeatedly to select
“Parental Lock”, then press
or b.
62GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Right
To listen to the locked channels
1 Select a locked channel you want to
listen to using Direct Tuning (page 60).
“Enter your 4-digit lock code.” appears.
2 Press SHIFT, then press the numeric
buttons to enter your 4-digit lock code.
The channel is tuned in.
To cancel the Parental Lock
1 Select a channel you want to unlock
using Direct Tuning (page 60).
Tuner Operations
2 Press TOOLS/OPTIONS.
The option menu appears.
3 Press V/v repeatedly to select
“Parental Lock”, then press
or b.
4 Press V/v repeatedly to select “OFF”,
then press
.
“Enter your 4-digit lock code.” appears.
5 Press SHIFT, then press the numeric
buttons to enter your 4-digit lock code.
“The channel has been unlocked.” appears
and the channel is unlocked.
Notes
• When you select a channel using Category Mode,
locked channels are skipped.
• When the receiver is reset to the initial settings, the
lock code returns to the default (0000), but the
Parental Lock settings are not removed.
• You cannot preset locked channels. If you set the
Parental Lock for a preset channel, the preset
information for that channel returns to the default.
• You cannot set the Parental Lock for channel 0 and
channel 184.
• You can set only one lock code on the receiver.
You cannot set individual lock codes for each
channel.
continued
63GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB04GET_STR-DN1010-CEL.fm
masterpage: Left
SIRIUS Satellite Radio message list
Message
appears on
TV screen
[Display]
Explanation
Remedies
Antenna
[ANTENNA]
The antenna is not connected
properly.
Check the connection between the SiriusConnect
Home tuner and the antenna.
Acquiring
[ACQUIRING]
The receiving condition is not
good.
Try moving the antenna to another location.
For details about the antenna location, refer to the
operating instructions supplied with the SiriusConnect
Home tuner.
UNSUB CH
[CALL 888,
539-SIRI]*
You have not subscribed for the
selected channel.
—
SR Tuner
[SR TUNER]
The SiriusConnect Home tuner is Check all the connections, and then turn the system on
not connected properly.
again. Also make sure if the AC adaptor supplied with
the SiriusConnect Home tuner is connected to a wall
socket.
Invalid
[INVALID]
You have entered an invalid
channel number.
The channel to be tuned-in is void due to the change
by the broadcast service, or the receiving condition is
not good.
Locked CH
[LOCKED CH]
The selected channel is locked.
—
SUB UPDT
[SUB UPDT]
The subscription information has
been updated.
—
Updating
[UPDATING]
Channel information is being
updated.
—
FW UPDT
[FW UPDT]
The SiriusConnect Home tuner
firmware is being updated.
—
––––
There is no text information in the This is not an error. The text information may not be
channel.
displayed depending on the system condition, for
example, right after the system has received a channel.
* “CALL 888” and “539-SIRI” appears on the display alternately.
64GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Right
Note
Enjoying Surround Sound
Selecting the sound field
This receiver can create multi channel
surround sound. You can select one of the
optimized sound fields from the receiver’s
preprogrammed sound fields.
.
SOUND
FIELD +/–
You cannot select “Analog Direct” when you select
DVD, DMPORT and HDMI 1-4 as input.
Auto Format Direct (A.F.D.)
mode
The Auto Format Direct (A.F.D.) mode allows
you to listen to high fidelity sound and select
the decoding mode for listening to a 2 channel
stereo sound as multi channel sound.
x A.F.D. AUTO (A.F.D. Auto)
Presets the sound as it was recorded/encoded
without adding any surround effects.
You can also use 2CH/A.DIRECT, A.F.D.,
MOVIE or MUSIC on the receiver.
2 channel sound mode
x MULTI ST. (Multi Stereo)
Outputs 2 channel left/right signals from all
speakers. However, sound may not be output
from certain speakers depending on the
speaker settings.
Movie mode
You can switch the output sound to 2 channel
sound regardless of the recording formats of
the software you are using, the playback
component connected, or the sound field
settings of the receiver.
You can take advantage of surround sound
simply by selecting one of the receiver’s preprogrammed sound fields. They bring the
exciting and powerful sound of movie theaters
into your home.
x 2CH ST. (2ch Stereo)
x C.ST.EX A (Cinema St EX A
DCS )
The receiver outputs the sound from the front
left/right speakers only. There is no sound
from the subwoofer.
Standard 2 channel stereo sources completely
bypass the sound field processing and multi
channel surround formats are downmixed to 2
channel.
x A. DIRECT (Analog Direct)
You can switch the audio of the selected input
to 2 channel analog input. This function
enables you to enjoy high quality analog
sources without any adjustment.
When using this function, only the volume and
front speaker level can be adjusted.
Reproduces the sound characteristics of the
Sony Pictures Entertainment “Cary Grant
Theater” cinema production studio. This is a
standard mode, great for watching almost any
type of movie.
x C.ST.EX B (Cinema St EX B
DCS )
Reproduces the sound characteristics of the
Sony Pictures Entertainment “Kim Novak
Theater” cinema production studio. This mode
is ideal for watching science-fiction or action
movies with lots of sound effects.
continued
65GB
STR-DN1010
4-174-068-11(1)
Enjoying Surround Sound
Press SOUND FIELD +/– repeatedly
to select the sound field you want.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
x C.ST.EX C (Cinema St EX C
DCS )
Reproduces the sound characteristics of the
Sony Pictures Entertainment scoring stage.
This mode is ideal for watching musicals or
films where orchestra music is featured in the
soundtrack.
masterpage: Left
x HALL (Hall)
Reproduces the acoustics of a classical concert
hall.
x JAZZ (Jazz Club)
Reproduces the acoustics of a jazz club.
x CONCERT (Live Concert)
x V.MULTI DIM. (V.M. Dimension
DCS )
Reproduces the acoustics of a 300-seat live
house.
Creates many virtual speakers from a single
pair of actual surround speakers.
x STADIUM (Stadium)
x PLII MV (PLII Movie)
Performs Dolby Pro Logic II Movie mode
decoding. This setting is ideal for movies
encoded in Dolby Surround. In addition, this
mode can reproduce sound in 5.1 channel for
watching videos of overdubbed or old movies.
x PLIIx MV (PLIIx Movie)
Performs Dolby Pro Logic IIx Movie mode
decoding. This setting expands Dolby Pro
Logic II Movie or Dolby Digital 5.1 to discrete
7.1 movie channels.
x PLIIz (PLIIz Height)
Performs Dolby Pro Logic IIz mode decoding.
This setting increases flexibility to expand a
5.1 to a 7.1 channel system. Its vertical
component gives a dimension of presence and
depth.
x NEO6 CIN (Neo:6 Cinema)
Performs DTS Neo:6 Cinema mode decoding.
A source recorded in 2 channel format is
decoded into 7 channels.
Music mode
You can take advantage of surround sound
simply by selecting one of the receiver’s
preprogrammed sound fields. They bring the
exciting and powerful sound of concert halls
into your home.
Reproduces the feeling of a large open-air
stadium.
x SPORTS (Sports)
Reproduces the feeling of sports broadcasting.
x PORTABLE (Portable Audio)
Reproduces a clear enhanced sound image
from your portable audio device. This mode is
ideal for MP3 and other compressed music.
x PLII MS (PLII Music)
Perform Dolby Pro Logic II Music mode
decoding. This setting is ideal for normal
stereo sources such as CDs.
x PLIIx MS (PLIIx Music)
Performs Dolby Pro Logic IIx Music mode
decoding. This setting is ideal for normal
stereo sources such as CDs.
x PLIIz (PLIIz Height)
Performs Dolby Pro Logic IIz mode decoding.
This setting increases flexibility to expand a
5.1 to a 7.1 channel system. Its vertical
component gives a dimension of presence and
depth.
x NEO6 MUS (Neo:6 Music)
Performs DTS Neo:6 Music mode decoding.
A source recorded in 2 channel format is
decoded into 7 channels. This setting is ideal
for normal stereo sources such as CDs.
66GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
When headphones are
connected
You can only select this sound field if the
headphones are connected to the receiver.
x HP 2CH (HP (2 ch))
This mode is selected automatically if you use
headphones (except Analog Direct). Standard
2 channel stereo sources completely bypass
the sound field processing and multi channel
surround formats are downmixed to 2
channels except LFE signals.
Note
When headphones are connected to the S-AIR
surround amplifier, the sound field is automatically
set to “HP (2 ch)”.
masterpage: Right
• The sound fields for music and movies do not work
in the following cases.
– Signals with a sampling frequency of more than
48 kHz are being received.
– Signals with more than 5.1 channel are being
received (except PLIIz).
• When one of the sound fields for music is selected,
no sound is output from the subwoofer if all the
speakers are set to “Large” on the Speaker Settings
menu. However, the sound will be output from the
subwoofer if
– the digital input signal contains LFE signals.
– the front or surround speakers are set to “Small”.
– the sound field for movie is selected.
– “Portable Audio” is selected.
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
Tips
This mode is selected automatically if you use
headphones when “Analog Direct” is selected.
Outputs the analog signals without processing
by the equalizer, sound field, etc.
• You can identify the encoding format of DVD
software, etc., by looking at the logo on the
package.
• Dolby Pro Logic IIx and Dolby Pro Logic IIz
decoding are effective when multi channel signals
are input.
• Sound fields with DCS marks use DCS
technology. For details on Digital Cinema Sound
(DCS), see “Glossary” (page 117).
If you connect a subwoofer
This receiver will generate a low frequency
signal for output to the subwoofer when there
is no LFE signal, which is a low-pass sound
effect output from a subwoofer to a 2 channel
signal. However, the low frequency signal is
not generated for “Neo:6 Cinema” or “Neo:6
Music” when all speakers are set to “Large”.
In order to take full advantage of the Dolby
Digital bass redirection circuitry, we
recommend setting the subwoofer’s cut off
frequency as high as possible.
To turn off the surround effect
for movie/music
Press SOUND FIELD +/– repeatedly to select
“2CH ST.” or “A.F.D. AUTO”.
You can also press 2CH/A.DIRECT
repeatedly on the receiver to select “2CH ST.”
or press A.F.D. repeatedly on the receiver to
select “A.F.D. AUTO”.
Notes on sound fields
• Depending on the speaker pattern settings, some
sound fields may not be available.
• You cannot select PLIIx and PLIIz at the same
time.
– PLIIx is available only when the speaker pattern
is set to a setting with surround back speaker(s).
– PLIIz is available only when the speaker pattern
is set to a setting with front high speakers.
67GB
STR-DN1010
4-174-068-11(1)
Enjoying Surround Sound
x HP DIRECT (HP (Direct))
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
When connecting Blu-ray disc players and other next generation HD
players
Digital audio formats that this receiver can decode depend on digital audio input jacks for the
components connected. This receiver supports the following audio formats.
Audio format
Maximum number
of channels
Connection of the playback component and
the receiver
COAXIAL/OPTICAL
HDMI
Dolby Digital
5.1
a
a
Dolby Digital EX
6.1
a
a
a)
7.1
×
a
Dolby TrueHDa)
7.1
×
a
DTS
5.1
a
a
DTS-ES
6.1
a
a
DTS 96/24
5.1
a
a
DTS-HD
High Resolution Audioa)
7.1
×
a
DTS-HD
Master Audioa)b)
7.1
×
a
Multi channel Linear PCMa)
7.1
×
a
Dolby Digital Plus
a) Audio signals are output in another format if the playback component does not correspond to the format. For
details, refer to the operating instructions of the playback component.
with a sampling frequency of more than 96 kHz are played back at 96 kHz or 88.2 kHz.
b) Signals
68GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Enjoying the surround
effect at low volume
levels
(NIGHT MODE)
masterpage: Right
Resetting sound fields to
the initial settings
Be sure to use the buttons on the receiver for
this operation.
?/1
This function allows you to retain a theater like
environment at low volume levels. This
function can be used with other sound fields.
When watching a movie late at night, you will
be able to hear the dialog clearly even at a low
volume level.
NIGHT
MODE
The NIGHT MODE function is activated. The
NIGHT MODE is set to on and off as you
press NIGHT MODE.
Note
1
Press ?/1 to turn off the
receiver.
2
While holding down MUSIC,
press ?/1.
“S.F. CLEAR” appears on the display and
all sound fields are reset to their initial
setting.
This function does not work in the following cases.
– Sound Field is set to “Analog Direct”.
– Signals with a sampling frequency of more than
48 kHz are being received.
Tip
While this function is on, the Bass, Treble, and
Effect Levels increase, and “D.Range Comp” is
automatically set to “MAX”.
69GB
STR-DN1010
4-174-068-11(1)
Enjoying Surround Sound
Press NIGHT MODE to select
“NIGHT ON”.
MUSIC
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
“BRAVIA” Sync Features
What is “BRAVIA” Sync?
“BRAVIA” Sync is compatible with Sony TV,
Blu-ray disc/DVD player, AV amplifier, etc.,
that is equipped with the Control for HDMI
function.
By connecting Sony components that are
compatible with the “BRAVIA” Sync with an
HDMI cable (not supplied), operation is
simplified as follows:
• One-Touch Play (page 72)
• System Audio Control (page 72)
• System Power Off (page 73)
• Theater/Theatre Mode Sync (page 73)
• Audio Return Channel (page 74)
Control for HDMI is a mutual control function
standard used by HDMI CEC (Consumer
Electronics Control) for HDMI (HighDefinition Multimedia Interface).
We recommend that you connect the receiver
to products featuring “BRAVIA” Sync.
Note
Depending on the connected component, the
Control for HDMI function may not work. Refer to
the operating instructions of the component.
masterpage: Left
Preparing for the
“BRAVIA” Sync
The receiver is compatible with the “Control
for HDMI-Easy Setting” function.
• If your TV is compatible with the “Control
for HDMI-Easy Setting” function, you can
set the Control for HDMI function of the
receiver and playback components
automatically by setting the TV (page 70).
• If your TV is not compatible with the
“Control for HDMI-Easy Setting” function,
set the Control for HDMI function of the
receiver, playback components and TV
individually (page 71).
If your TV is compatible with the
“Control for HDMI-Easy Setting”
function
The Control for HDMI function of the receiver
can be turned on simultaneously by turning on
the Control for HDMI function of the TV.
1 Connect the receiver, TV and playback
components via HDMI connection
(page 27).
(The respective components must be
compatible with the Control for HDMI
function).
2 Turn on the receiver, TV and playback
components.
3 Turn the Control for HDMI function of
the TV on.
The Control for HDMI function of the
receiver and all the connected components
are turned on simultaneously. When the
setup is completed, “COMPLETE” will
appear.
For details on setup of the TV, refer to the
operating instructions of your TV.
70GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
If your TV is not compatible with
the “Control for HDMI-Easy
Setting” function
GUI MODE
V/v/b,
MENU
masterpage: Right
Notes
• Before you do the “Control for HDMI-Easy
Setting” from the TV, be sure to turn on the TV,
connected components and receiver.
• If the playback components cannot function after
you have made the settings for “Control for HDMIEasy Setting”, check the Control for HDMI setting
on your TV.
• If the connected components do not support
“Control for HDMI-Easy Setting”, you need to set
the Control for HDMI function for the connected
components to on before you perform the “Control
for HDMI-Easy Setting” from the TV.
1 Perform the steps given in “If your TV is
compatible with the “Control for HDMIEasy Setting” function” (page 70).
2 Press GUI MODE.
“BRAVIA” Sync Features
After “MENU ON” appears on the display
for a while, “GUI” appears and the GUI
menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
3 Press V/v repeatedly to select
“Settings”, then press
or b.
The Settings menu list appears on the TV
screen.
4 Press V/v repeatedly to select “HDMI”,
then press
or b.
5 Press V/v repeatedly to select “Ctrl for
HDMI”, then press
or b.
6 Press V/v repeatedly to select “ON”,
then press
.
The Control for HDMI function is set to on.
7 Set the Control for HDMI function of the
connected component to on.
If the Control for HDMI function for the
connected component is already set to on,
you do not need to change the setting.
For details on setting the TV and connected
components, refer to the operating
instructions of the respective components.
71GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Playing back components
with one-touch operation
(One-Touch Play)
By a simple operation (one-touch),
components connected to the receiver with
HDMI connections start automatically. You
can enjoy the sound/image using connected
components.
When you set “Pass Through” to “AUTO” or
“ON”, sound and image can be output only
from the TV while the receiver remains in
standby mode.
When you start playback a connected
component, the receiver and TV operation are
simplified as follow:
masterpage: Left
Enjoying the TV sound
from the speakers
connected to the receiver
(System Audio Control)
You can enjoy the TV sound from the speakers
connected to the receiver by a simple
operation.
You can operate System Audio Control
function using the TV menu. For details, refer
to the operating instructions of the TV.
TV
Receiver
Sets System Audio
Control to on
• Turns on (if in
standby mode)
• Switches to
appropriate
HDMI input
Minimizes TV
volume
Outputs TV
sound
Receiver and TV
Turns on (if in standby mode)
Switches to appropriate HDMI input
Notes
• Depending on the TV, the start of the content may
not be output.
• Depending on the settings, the receiver may not
turns on when “Pass Through” is set to “AUTO” or
“ON”.
Tip
You can also select a connected component, such as
DVD/Blu-ray disc player using the TV menu. The
receiver and TV will automatically switch to the
appropriate HDMI input.
You can also use the System Audio Control
function as follows.
• If you turn on the receiver while the TV is
turned on, the System Audio Control
function will automatically be set to on and
the TV sound will output from the speakers
connected to the receiver. However, if you
turn off the receiver, the sound will output
from the TV speakers.
• When you adjust the TV volume, the
receiver’s volume is adjusted
simultaneously.
Notes
• If System Audio Control does not function
according to your TV setting, refer to the operating
instructions of the TV.
• When “Ctrl for HDMI” is set to “ON”, the “Audio
Out” settings in the HDMI Settings menu will set
automatically depending on the System Audio
Control settings.
• When you connect a TV that does not have System
Audio Control function, the System Audio Control
function does not work.
• If the TV is turned on before turning on the
receiver, the TV sound will not be output for a
moment.
72GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Turning off the receiver
with the TV
(System Power Off)
When you turn the TV off by using the
POWER button on the TV’s remote, the
receiver and the connected components turn
off automatically.
You can also use the receiver’s remote to turn
off the TV.
AV ?/1
TV
Press TV, then press AV ?/1.
Notes
• Set the TV Standby Synchro to “ON” before using
the System Power Off function. For details, refer to
the operating instructions of the TV.
• Depending on the status, the connected
components may not be turned off. For details,
refer to the operating instructions of the connected
components.
Enjoying movies with the
optimum sound field
(Theater/Theatre Mode
Sync)
THEATER/
THEATRE
Press THEATER or THEATRE on
the remote of the receiver, TV, or
the Blu-ray disc player, while
pointing the remote towards the TV.
The sound field switches to “C.ST.EX B”.
To return to the previous sound field, press
THEATER or THEATRE again.
Note
The sound field may not switch depending on the
TV.
Tip
The sound field may be changed back to the
previous one when you change the TV’s input.
73GB
STR-DN1010
4-174-068-11(1)
“BRAVIA” Sync Features
The TV, receiver and the components
connected via HDMI are turned off.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
Notes
Enjoying the TV sound via
an HDMI cable
(Audio Return Channel)
• This function does not work when you set “Ctrl for
HDMI” to “OFF” in the HDMI Settings menu.
• This function is only available when
– your TV is compatible with Audio Return
Channel (ARC) function.
– INPUT MODE is set to “AUTO”.
The Audio Return Channel (ARC) function
enables the TV outputs the audio signals to the
receiver via an HDMI cable connected to the
HDMI TV OUT jack.
You can enjoy the TV sound from the speakers
connected to the receiver without connecting
the TV AUDIO IN or TV OPTICAL IN jack.
GUI
MODE
V/v/b,
MENU
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“Settings”, then press
or b.
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“HDMI”, then press
or b.
4
Press V/v repeatedly to select
“ARC”, then press
or b.
5
Press V/v repeatedly to select
“ON”, then press
.
74GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
S-AIR Operations
Room B
S-AIR sub unit
(S-AIR receiver)
About S-AIR products
Room A
S-AIR main unit
(this receiver)
S-AIR sub unit
(surround amplifier)
S-AIR Operations
This receiver is compatible with the S-AIR
function (page 119), which allows wireless
sound transmission between S-AIR products.
There are two types of S-AIR product.
• S-AIR main unit (this receiver):
The S-AIR main unit is for transmitting
sound.
You can use up to 3 S-AIR main units. (The
number of usable S-AIR main unit depends
on the use environment.)
• S-AIR sub unit (not supplied):
The S-AIR sub unit is for receiving sound.
– Surround amplifier: You can enjoy
surround and surround back speakers
sound wirelessly. For details, refer to the
operating instructions supplied with the
surround amplifier.
– S-AIR receiver: You can enjoy system
sound in another room.
These S-AIR products can be purchased as an
option (the S-AIR product lineup differs
depending on the area).
See the notes or instructions for the S-AIR sub
unit in this manual only when the S-AIR sub
unit is used.
masterpage: Right
Notes
• The S-AIR menu and parameters only available
when you have inserted the wireless transmitter.
• When the speaker pattern is set to a setting with
front high speakers, the surround back speakers
sound is not output from surround amplifier even if
the surround amplifier is used.
75GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
About environments where
S-AIR products (S-AIR main unit
and sub unit) are used
S-AIR products use a radio frequency of
2.4 GHz. Certain electronic equipment or
other factors may cause lost connection or
instability in S-AIR reception.
• Electronic equipment influence
The following may cause interference or
cross talk.
– Cellular phones, cordless phones
– Wireless LAN, personal computers
– Game machines using radio signals
– Microwave ovens
masterpage: Left
Setting up an S-AIR
product
Before using an S-AIR product, be sure to
perform the following settings to establish the
sound transmission.
• Inserting the wireless transmitter/transceiver
(page 35).
• Establishing sound transmission between
the S-AIR main unit and S-AIR sub unit (ID
setting) (page 77).
• Pairing the S-AIR main unit with a specific
S-AIR sub unit (Pairing operation)
(page 78).
GUI MODE
• Other factors
The following may cause poor reception.
– Materials or structures, such as walls and
floors
– The location where an S-AIR product is
placed
When using S-AIR products, place them as
far as possible from the above electronic
equipment, or place where S-AIR reception
is stable.
V/v/b,
RETURN/
EXIT O
MENU
76GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Establishing sound transmission
between the S-AIR main unit and
S-AIR sub unit (ID setting)
When you match the ID of the S-AIR main
unit and the S-AIR sub unit, you can establish
sound transmission. You can use multiple
S-AIR main unit by setting a different ID for
each unit.
masterpage: Right
8 Set the S-AIR sub unit to the same ID.
Sound transmission is established as
follows (example):
S-AIR main unit (this receiver)
ID A
To set the ID of the S-AIR main
unit
1 Press GUI MODE.
After “MENU ON” appears on the display
for a while, “GUI” appears and the GUI
menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2 Press V/v repeatedly to select
“Settings”, then press
or b.
The Settings menu list appears on the TV
screen.
3 Press V/v repeatedly to select “S-AIR”,
or b.
Note
When the S-AIR transmitter (not supplied) is not
inserted into the S-AIR main unit, “S-AIR”
cannot be selected.
4 Press V/v repeatedly to select “S-AIR
ID”, then press
or b.
The S-AIR ID menu appears.
5 Press V/v repeatedly to select the ID
(A, B or C) you want, then press
.
The ID of the S-AIR main unit is set. “Set
S-AIR ID of the sub unit to the same as that
of the main unit” appears.
6 Press
ID A
S-AIR sub unit
Tip
To confirm the current ID, performs steps 1 to 3
above. When you pair the S-AIR main unit with
the S-AIR sub unit (page 78), “(Pairing)”
appears beside the ID on the TV screen in the
GUI menu.
To exit the menu
Press MENU.
To set the ID of the S-AIR sub
unit
Be sure to match the ID on S-AIR sub unit you
want to the S-AIR main unit.
For details on setting the ID of the surround
amplifier and S-AIR receiver, refer to the
operating instructions supplied with the
surround amplifier and S-AIR receiver.
.
7 Press GUI MODE.
The GUI menu turns off.
continued
77GB
STR-DN1010
4-174-068-11(1)
S-AIR Operations
then press
ID A
S-AIR sub unit
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
To use multiple S-AIR main
units
x Before pairing
You can use multiple S-AIR main units by
setting a different ID for each component.
Sound transmission is established as follows
(example):
S-AIR main unit
(this receiver)
masterpage: Left
Sound transmission is established by the ID
(example).
Your room
Neighbor
S-AIR main unit
(this receiver)
Other S-AIR main
unit
ID A
ID A
ID B
ID A
ID A
S-AIR sub
unit
ID A
S-AIR sub
unit
ID B
S-AIR sub unit
ID A
S-AIR sub unit
S-AIR sub unit
Notes
x After pairing
• Sources with copyright protection may not be
playable on S-AIR sub unit.
• If you have connected surround amplifier,
surround sound will not be output from S-AIR
main unit.
Sound transmission is established between the
paired S-AIR main unit and S-AIR sub unit(s)
only.
Pairing the S-AIR main unit with
a specific S-AIR sub unit
(Pairing operation)
To establish sound transmission, you need to
set the same ID for your S-AIR main unit and
S-AIR sub unit.
However, if your neighbors have S-AIR
products and their IDs are the same as yours,
your neighbors could receive the sound of
your S-AIR main unit or vice versa.
To prevent this, you can pair the S-AIR main
unit with a specific S-AIR sub unit by
performing the pairing operation.
Your room
Neighbor
S-AIR main unit
(this receiver)
No transmission
ID A
S-AIR sub unit
ID A
S-AIR sub unit
Pairing
78GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
To perform pairing
1
2
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
4
Press V/v repeatedly to select
“Settings”, then press
or b.
5
9
Press B/b repeatedly to select
“Finish” or “Continue”, then
press
.
• “Finish”: Finishes pairing.
• “Continue”: Continues to perform
pairing to another S-AIR sub unit.
Tip
You can confirm the pairing completion or the
current ID by checking the “S-AIR Settings”
screen. “Pairing” appears beside the current
S-AIR ID.
10 Press GUI MODE.
The GUI menu turns off.
Note
After you have performed pairing, if you select
the “S-AIR ID” menu, the ID setting (“A”, “B”
or “C”) that you last used is displayed.
Press V/v repeatedly to select
“Pairing”, then press
or b.
“Put the S-AIR sub unit near the S-AIR
main unit. Turn on power and start
pairing.” appears on the TV screen. The
S-AIR main unit is ready to start pairing.
7
• Perform pairing within 5 minutes in step 7. If
you do not, pairing is recognized as failed,
and the screen changes accordingly. In this
case, see “If pairing fails” (page 79).
• When sound transmission is established,
“Pairing complete. To do the pairing another
one, select “Continue”.” appears.
Press V/v repeatedly to select
“S-AIR”, then press
or b.
When the S-AIR transmitter (not supplied) is
not inserted into the S-AIR main unit, “S-AIR”
cannot be selected.
6
Notes
Press B/b repeatedly to select
“Yes”, then press
.
The S-AIR main unit starts pairing.
“Pairing. Do the pairing operation with
the S-AIR sub unit.” appears.
Note
If pairing fails
“Pairing failed. Retry?” appears.
To perform pairing again, select “Yes”.
To finish pairing, select “No”.
To quit pairing during setting
Press RETURN/EXIT O.
To cancel pairing
Perform the ID setting of the main unit
according to the procedure of “To set the ID of
the S-AIR main unit” (page 77). If you reset
the ID (even the same ID again), pairing is
canceled.
79GB
STR-DN1010
4-174-068-11(1)
S-AIR Operations
The Settings menu list appears on the TV
screen.
Start pairing of the S-AIR sub
unit.
Refer to the operating instructions of the
S-AIR sub unit.
Match the IDs of the S-AIR main
unit and the S-AIR sub unit.
• To set the ID of the S-AIR main unit,
see “To set the ID of the S-AIR main
unit” (page 77).
• To set the ID of the S-AIR sub unit,
refer to the operating instructions
supplied with the S-AIR sub unit.
3
8
Place the S-AIR sub unit that
you want to pair near the S-AIR
main unit.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Enjoying the system’s
sound in another room
(For the S-AIR receiver only (not
supplied))
You can enjoy the system’s sound in another
room by using the S-AIR receiver. The S-AIR
receiver can be placed in another room for
enjoying the system’s sound there.
For details of the S-AIR receiver, refer to the
operating instructions supplied with the S-AIR
receiver.
2
3
Press V/v repeatedly to select
“Settings”, then press
or b.
The Settings menu list appears on the TV
screen.
4
Press V/v repeatedly to select
“S-AIR”, then press
or b.
Note
When the S-AIR transmitter (not supplied) is
not inserted into the S-AIR main unit, “S-AIR”
cannot be selected.
V/v/b,
5
Press V/v repeatedly to select
“S-AIR Mode”, then press
or b.
6
Press V/v repeatedly to select
the setting you want, then
press
.
MENU
Set the ID of the S-AIR receiver
to match the ID of the S-AIR
main unit.
• Party: The S-AIR receiver outputs
sound according to the input selected on
the S-AIR main unit.
• Separate: You can select the input you
want for the S-AIR receiver while the
input of the S-AIR main unit remain
unchanged. When “Separate” is
selected, you can only select “SA-CD/
CD”, “DMPORT”, “FM TUNER”,
“AM TUNER”, “SIRIUS”* and the
input that is currently selected on the
S-AIR main unit.
• To set the ID of the S-AIR main unit,
see “To set the ID of the S-AIR main
unit” (page 77).
• To set the ID of the S-AIR receiver,
refer to the operating instructions
supplied with the S-AIR receiver.
Notes
• When you are using another S-AIR sub unit,
such as a surround amplifier, do not change
the ID of the S-AIR main unit. Set the ID of
the S-AIR receiver to match the ID of the
S-AIR main unit.
• When you pair the S-AIR main unit and
another S-AIR sub unit, such as a surround
amplifier, you also need to pair the S-AIR
main unit and the S-AIR receiver. For details,
see “Pairing the S-AIR main unit with a
specific S-AIR sub unit (Pairing operation)”
(page 78).
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
GUI MODE
1
masterpage: Left
Note
When the input selected on the S-AIR
receiver is same as S-AIR main unit, the
input of the S-AIR receiver will change
according to the S-AIR main unit.
7
Press GUI MODE.
The GUI menu turns off.
80GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
8
Select the desired input on the
S-AIR receiver.
x When “Party” is set
The S-AIR receiver’s input changes
sequentially as you change the input on
the S-AIR main unit or S-AIR receiver.
x When “Separate” is set
The S-AIR receiver’s input changes by
pressing S-AIR CH of the S-AIR
receiver.
Note
Changing the channel
for better sound
transmission
If you use multiple wireless systems which
share the 2.4 GHz band, such as wireless LAN
or Bluetooth, the transmission of S-AIR
products or other wireless systems may be
unstable. In this case, transmission may be
improved by changing the “RF Change”
setting.
When TUNER (FM/AM band) is selected on
the S-AIR main unit, you can only select the
same band for the tuner on the S-AIR receiver.
However, you can select input other than
TUNER on the S-AIR receiver.
9
masterpage: Right
GUI MODE
V/v/b,
Adjust the volume on the S-AIR
receiver.
MENU
* Models of area code U2, CA2 only.
Notes
To control the system from the
S-AIR receiver
1
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
You can control the system from the S-AIR
receiver by using the following buttons.
Press
Operation
N, X, x,
Share the same operations on the
remote
./>
S-AIR CH
Change the function of the
system
For details, refer to the operating instructions
of the S-AIR receiver.
Press GUI MODE.
Press V/v repeatedly to select
“Settings”, then press
or b.
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“S-AIR”, then press
or b.
Note
When the S-AIR transmitter (not supplied) is
not inserted into the S-AIR main unit, “S-AIR”
cannot be selected.
continued
81GB
STR-DN1010
4-174-068-11(1)
S-AIR Operations
• The sound of the S-AIR receiver may be cut off by
operation of the S-AIR main unit.
• When the sound is other than 2 channel stereo,
multi channel sound is downmixed to 2 channel.
• Signals with a sampling frequency of more than
96 kHz cannot output to the S-AIR receiver.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
4
Press V/v repeatedly to select
“RF Change”, then press
or
b.
5
Press V/v repeatedly to select
the setting you want, then
press
.
• AUTO: Normally select this. The
system changes “RF Change” to “ON”
or “OFF” automatically.
• ON: The system transmits sound by
searching for a better channel for
transmitting.
• OFF: The system transmits sound by
fixing the channel for transmitting.
6
Press GUI MODE.
The GUI menu turns off.
7
When you set “RF Change” to
“OFF”, select the ID so that
sound transmission is most
stable.
masterpage: Left
Stabilizing S-AIR
reception
Check the following when S-AIR reception is
poor or unstable.
– Confirm the wireless adapters are inserted
correctly (page 35).
– Confirm that the S-AIR IDs of the S-AIR
main unit and sub unit are the same
(page 77).
When S-AIR reception is poor
Check the following.
• Keep cords that are connected to the S-AIR
product (AC power cord (mains lead),
speaker cords, or other cords) away from the
wireless adapter and slot.
Notes
• In most cases, you will not need to change this
setting.
• If “RF Change” is set to “OFF”, transmission
between the S-AIR main unit and S-AIR sub unit
can be performed using one of the following
channels.
– S-AIR ID A: equivalent channel for IEEE
802.11b/g channel 1
– S-AIR ID B: equivalent channel for IEEE
802.11b/g channel 6
– S-AIR ID C: equivalent channel for IEEE
802.11b/g channel 11
• The transmission may be improved by changing
the transmission channel (frequency) of the other
wireless system(s). For details, refer to the
operating instructions of the other wireless
system(s).
• Keep as much space as possible around
S-AIR products.
– Avoid placing S-AIR products on top of or
directly below other electronic equipment.
– Avoid placing S-AIR products in a closed
rack, metal rack or under a table.
82GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
• Adjust the location (height, orientation, and
place in the room) of S-AIR products until
reception is the most stable.
– Place so that the wireless adapters of the
S-AIR main unit and sub unit are closer.
masterpage: Right
Enjoying the S-AIR
receiver while the S-AIR
main unit is in standby
mode
(For the S-AIR receiver only (not
supplied))
You can enjoy the S-AIR receiver while the
S-AIR main unit is in standby mode by setting
“S-AIR Stby” to “ON”.
GUI MODE
V/v/b,
– Place so that S-AIR products are separated
from other wireless devices.
MENU
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
If you still cannot improve S-AIR reception,
change the “RF Change” setting (page 81).
2
Press V/v repeatedly to select
“Settings”, then press
or b.
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“S-AIR”, then press
or b.
Note
When the S-AIR transmitter (not supplied) is
not inserted into the S-AIR main unit, “S-AIR”
cannot be selected.
4
Press V/v repeatedly to select
“S-AIR Stby”, then press
or
b.
continued
83GB
STR-DN1010
4-174-068-11(1)
S-AIR Operations
– Place so that S-AIR products are separated
from metal doors or tables.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
5
Press V/v repeatedly to select
the setting you want.
• ON: You can enjoy the S-AIR receiver
while the S-AIR main unit is in standby
mode or turned on.
• OFF: You cannot enjoy the S-AIR
receiver while the S-AIR main unit is in
standby mode.
To exit the menu
Press MENU.
Notes
• When you set “S-AIR Stby” to “ON”, the power
consumption increases during the standby mode.
• When the wireless transmitter is removed from the
S-AIR main unit, “S-AIR Stby” is set to “OFF”
automatically.
• If you have selected TUNER (FM/AM band) on
the S-AIR main unit before you turn it off and
“S-AIR Stby” is set to “ON”, you can only select
the same band for the tuner on the S-AIR receiver.
However, you can select input other than TUNER
on the S-AIR receiver.
• The sound of the S-AIR receiver may be cut off by
operation of the S-AIR main unit.
• When the receiver is in standby mode,
“A.STANDBY” appears on the display if “S-AIR
Stby” is set to “ON”.
masterpage: Left
Advanced Operations
Switching between
digital and analog audio
(INPUT MODE)
When you connect components to both digital
and analog audio input jacks on the receiver,
you can fix the audio input mode to either of
them, or switch from one to the other,
depending on the type of material you intend
to watch.
1
Press INPUT SELECTOR +/– on
the receiver to select the input.
You can also use the input buttons on the
remote.
2
Press INPUT MODE repeatedly
on the receiver to select the
audio input mode.
The selected audio input mode appears on
the display.
Audio input modes
x AUTO
Gives priority to digital audio signals when
there are both digital and analog connections.
If there are no digital audio signals, analog
audio signals are selected.
x ANALOG
Specifies the analog audio signals input to the
AUDIO IN (L/R) jacks.
84GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Right
Notes
• Some audio input modes may not be set up
depending on the input.
• When either the HDMI 1-4 input, DMPORT input
or SIRIUS* is selected, “------” appears on the
display, and you cannot select other modes. Select
an input mode other than the HDMI 1-4 input,
DMPORT input or SIRIUS* then set the audio
input mode.
• When “Analog Direct” is being used, audio input is
automatically set to “ANALOG”. You cannot
select other modes.
Enjoying the sound/
images from other inputs
You can reassign audio and/or video signals to
another input when they are not currently
being used.
For example when you want to connect your
DVD player but cannot find an unused input:
DVD player
* Models of area code U2, CA2 only.
To OPTICAL
BD IN jack
(audio signal)
To COMPONENT
VIDEO IN 1 jacks
(video signal)
Assign to DVD input jack
using “Input Assign” in
the Input Option menu.
Receiver
1
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Press V/v repeatedly to select
“Input”, then press
or b.
BD
Input
DVD
SAT/CATV
TV
VIDEO 1
3
Press V/v repeatedly to select
the input name you want to
assign.
continued
85GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
2
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
4
masterpage: Left
Press TOOLS/OPTIONS.
BD
Input
DVD
SAT/CATV
Input Assign
Name lnput
TV
VIDEO 1
5
Press V/v repeatedly to select
“Input Assign”, then press
or b.
The “Input Assign” screen appears.
6
Select the audio and/or video
signals you want to assign to
the input which you selected in
step 3 using V/v/B/b.
Input Assign
Select Video
Select Audio
COMP.2
SAT OPT
COMP.3
DVD COAX
CVBS
ANALOG
RETURN
7
Press
to enter the setting.
86GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Right
Input name
BD
DVD
SAT/CATV
VIDEO 1
VIDEO 2
SA-CD/CD/
CD-R
Assignable COMP.1
video input
COMP.2
jacks
COMP.3
a*
a
a
a
a
a
a
a*
a
a
a
a
a
a
a*
a
a
a
CVBS
a
–
a
a*
a*
–
HDMI1
a
a
a
a
a
a
HDMI2
a
a
a
a
a
a
HDMI3
a
a
a
a
a
a
HDMI4
a
a
a
a
a
a
NONE
Assignable BD OPT
audio input
SAT OPT
jacks
DVD COAX
ANALOG
–
a
–
–
–
a*
a*
a
–
a
a
a
–
a
a*
a
a
a
a
a*
a
a
a
a
a
–
a
a*
a*
a*
* Initial setting
Notes
Advanced Operations
• You cannot assign optical signals from an input
source to the optical input jacks on the receiver.
• When you assign the digital audio input, the
INPUT MODE setting may change automatically.
• You cannot reassign more than one HDMI input to
the same input.
• You cannot reassign more than one digital audio
input to the same input.
• You cannot reassign more than one component
video input to the same input.
87GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
Notes
Using a bi-amplifier
connection
1 Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
• Set “SB Assign” to “BI-AMP” before you perform
Auto Calibration.
• If you set “SB Assign” to “BI-AMP”, the speaker
level and distance settings of the surround back
speakers and front high speakers become invalid,
and those of the front speakers are used.
• If you set “SP Pattern” to a setting with surround
back speakers or front high speakers, you cannot
set “SB Assign” to “BI-AMP”.
Press V/v repeatedly to select
“Settings” then press
or b.
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“Speaker”, then press
or b.
4
Press V/v repeatedly to select
“SP Pattern”, then press
or
b.
5
Press V/v repeatedly to select
the appropriate speaker pattern
so that there are no surround
back speakers and front high
speakers, then press
.
6
Press V/v repeatedly to select
“SB Assign”, then press
or
b.
7
Press V/v repeatedly to select
“BI-AMP”, then press
.
The same signals output from the
SPEAKERS FRONT A terminals can be
output from the SPEAKERS
SURROUND BACK/FRONT HIGH/
BI-AMP/FRONT B terminals.
To exit the menu
Press MENU.
88GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Using the setting menu
2
You can adjust various settings for speakers,
surround effects, etc. using the setting menu.
To display the menu of the receiver on the TV
screen, make sure that the receiver is in “GUI
MODE” by following the steps in “To turn
“GUI MODE” on and off” (page 44).
masterpage: Right
Press V/v repeatedly to select
“Settings”, then press
or b
to enter the menu mode.
The Setting menu list appears on the TV
screen.
Auto Cal.
AM
AM
SR
Speaker
Surround
SR
GUI MODE
EQ
V/v/b,
RETURN/
EXIT O
MENU
1
Settings
3
Audio
Press V/v repeatedly to select
the menu item you want, then
press
or b.
Example: When you select “Auto Cal.”.
Press GUI MODE.
After “MENU ON” appears on the
display for a while, “GUI” appears and
the GUI menu appears on the TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Auto Cal.
Speaker
Surround
EQ
Settings
Audio
Input
DVD
SAT/CATV
Music
TV
Video
4
VIDEO 1
Press V/v repeatedly to select
the parameter you want, then
press
or b.
To return to the previous screen
Press RETURN/EXIT O.
To exit the menu
Press MENU.
Note
SR
appears for models of area code U2, CA2 only.
continued
89GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
BD
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
Setting menu list
Menu
Description
Auto Cal.
Sets the speaker level or
distance and makes the
measurement automatically
(page 90).
Speaker
Sets the speaker position
manually (page 91).
Surround
Adjusts the sound field
(surround effect) you choose
(page 95).
EQ
Adjusts the equalizer (bass/
treble sound) (page 96).
Audio
Sets various sound items
(page 96).
Video
Adjusts the resolution of
analog video signals (page
97).
HDMI
Makes settings for sound/
images from components
connected to the HDMI jacks
(page 98).
System
Sets the receiver switch to
standby mode automatically
(page 100).
S-AIR
Makes settings for S-AIR
operations (page 75).
Auto Calibration menu
You can make settings for the Auto
Calibration function to suit your preference.
Auto Cal. Start (Auto Calibration
start)
Lets you perform Auto Calibration. For
details, see “2: Performing Auto Calibration”
(page 40).
Auto Cal. Type (Auto Calibration
type)
Lets you select the Auto Calibration type for
each seating position. For details, see step 4 of
“3: Confirming/saving the measurement
results” (page 41).
Note
You can select this parameter only when you have
performed the Auto Calibration and saved the
measurement result.
Position
You can register 3 patterns as Position 1, 2,
and 3, depending on the listening position,
listening environment, and measurement
conditions.
90GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
To register settings for the
listening environment
You can select the seating position you want
and register the measurement results of the
Auto Calibration for that seating position.
1 Press V/v repeatedly to select
“Position”, then press
or b.
2 Press V/v repeatedly to select the
position (Position 1, 2, 3) for which you
want to register the measurement
result, then press
.
3 Press V/v repeatedly to select “Auto
Cal. Start”, then press
or b.
The measurement results is registered as
the position you selected in step 2.
4 Press
to select “START”.
5 Repeat step 1 to 3 to register another
seating position.
To select the registered seating
position
1 Press V/v repeatedly to select
“Position”, then press
or b.
2 Press V/v repeatedly to select the
Name Input (Naming position)
You can rename the position name.
1 Select the “Position” for which you want
to name.
2 Press V/v repeatedly to select “Name
Input”, then press
or b.
3 Press V/v/B/b to select a character,
then press
.
The name you entered is registered.
Speaker Settings menu
You can adjust each speaker manually.
You can also adjust the speaker levels after the
Auto Calibration is completed.
Note
The speaker settings are only for the current seating
position.
SP Pattern (Speaker pattern)
Select “SP Pattern” according to the speaker
system which you are using. You do not need
to select the speaker pattern after Auto
Calibration.
1 Press V/v repeatedly to select
“SP Pattern”, then press
or b.
The “SP Pattern” screen appears.
2 Press V/v repeatedly to select the
speaker pattern you want, then press
.
3 Press RETURN/EXIT O.
SB Assign (Surround back
speaker assign)
You can make settings for the surround back
speaker(s) or front high speaker(s). Before you
change “SB Assign” to “BI-AMP” or
“Speaker B”, be sure you have set “SP
Pattern” to a setting without surround back
speakers or front high speakers.
• Speaker B
If you connect an additional front speaker
system to the SPEAKERS SURROUND
BACK/FRONT HIGH/BI-AMP/FRONT B
terminals, select “Speaker B”.
• BI-AMP
If you connect front speakers to the
SPEAKERS SURROUND BACK/FRONT
HIGH/BI-AMP/FRONT B terminals using a
bi-amplifier connection, select “BI-AMP”.
continued
91GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
position (Position 1, 2, 3) you want,
then press
.
The registered seating position is selected.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
• OFF
If you do not use “Speaker B” or “BI-AMP”,
select “OFF”.
To adjust the distance from the
seating position to each
speaker
Note
You can adjust the distance from the listening
position to each speaker (front left/right, front
left/right high, center, surround left/right,
surround back left/right, subwoofer).
Set “SB Assign” to “OFF”, then connect the
surround back speakers to this receiver when you
want to change the connection from a bi-amplifier
connection or speakers front B connection to a
surround back speakers connection. Re-set up the
speakers after you connect the surround back
speakers. See “Calibrating the appropriate speaker
settings automatically (Auto Calibration)”
(page 38).
Manual Setup
You can adjust each speaker manually on the
“Manual Setup” screen. You can also adjust
the speaker levels after the Auto Calibration is
completed.
1 Press V/v/B/b repeatedly to select the
speaker on the screen for which you
want to adjust the distance from the
seating position, then press
.
2 Press B/b repeatedly to select “Dist:”.
3 Press V/v repeatedly to set the
distance of the selected speaker, then
press
.
You can adjust the distance from 3 feet
3 inches to 32 feet 9 inches (1.00 meter to
10.00 meters) in 1 inch (0.01 meter) steps.
Notes
To adjust the speaker level
You can adjust each speaker’s level (front left/
right, front left/right high, center, surround
left/right, surround back left/right,
subwoofer).
1 Press V/v/B/b repeatedly to select the
speaker on the screen for which you
want to adjust the level, then press
.
2 Press B/b repeatedly to select “Lvl:”.
3 Press V/v repeatedly to set the level of
the selected speaker, then press
.
For front left/right speakers, you can adjust
the level from –10.0 dB to +10.0 dB in
0.5 dB steps. For other speakers, you can
adjust the level from –20.0 dB to +10.0 dB
in 0.5 dB steps.
• Depending on the speaker pattern setting, some
parameters may not be available.
• This function does not work in the following cases.
– Sound Field is set to “Analog Direct”.
– Signals with a sampling frequency of more than
96 kHz are being received.
To adjust the size of each
speaker
You can adjust each speaker’s (front left/right,
front left/right high, center, surround left/right,
surround back left/right) size.
1 Press V/v/B/b repeatedly to select the
speaker on the screen for which you
want to adjust the size, then press
.
2 Press B/b repeatedly to select “Size:”.
Note
When one of the sound fields for music is selected,
no sound is output from the subwoofer if all the
speakers are set to “Large”. However, the sound will
be output from the subwoofer if
– the digital input signal contains LFE signals.
– the front or surround speakers are set to “Small”.
– the sound field for movie is selected.
– “Portable Audio” is selected.
92GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
3 Press V/v repeatedly to set the size of
the selected speaker, then press
.
• Large
If you connect large speakers that will
effectively reproduce bass frequencies,
select “Large”. Normally, select “Large”.
• Small
If the sound is distorted, or you feel a lack
of surround effects when using multi
channel surround sound, select “Small” to
activate the bass redirection circuitry and
output the bass frequencies of each
channel from the subwoofer or other
“Large” speakers.
Note
masterpage: Right
Crossover Frequency (Speaker
crossover frequency)
Lets you set the bass crossover frequency of
speakers that the speaker size has been set to
“Small” in the Speaker Settings menu.
Measured speaker crossover frequency is set
for each speaker after the Auto Calibration.
1
Press V/v repeatedly to select
the speaker on the screen you
want to adjust, then press
.
2
Press V/v repeatedly to adjust
the value, then press
.
This function does not work when “Analog Direct”
is being used.
Tips
Test Tone
You can select the test tone type on the “Test
Tone” screen.
Tips
• To adjust the level of all speakers at the same time,
press MASTER VOL +/–. You can also use
MASTER VOLUME on the receiver.
• The adjusted value is shown on the TV screen
during adjustment.
To output test tone from each
speaker
You can output test tone from the speakers in
sequence.
1 Press B/b repeatedly to select “Test
Tone”, then press
.
2 Press V/v repeatedly to adjust the
parameter, then press
.
• OFF
• AUTO
The test tone is output from each speaker
in sequence.
• FL, CNT, FR, SR, SB, SBR, SBL, SL,
LH, RH, SW
You can select which speakers will output
the test tone.
3 Press V/v repeatedly to adjust the
speaker level, then press
.
continued
93GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
• The “Large” and “Small” settings for each speaker
determine whether the internal sound processor
will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the subwoofer or other “Large”
speakers.
However, since bass sound has a certain amount of
directionality, it is best not to cut it, if possible.
Therefore, even when using small speakers, you
can set them to “Large” if you want to output the
bass frequencies from that speaker. On the other
hand, if you are using a large speaker, but prefer
not to have bass frequencies output from that
speaker, set it to “Small”.
If the overall sound level is lower than you prefer,
set all speakers to “Large”. If there is not enough
bass, you can use the equalizer to boost the bass
levels.
• The surround back speakers will be set to the same
setting as that of the surround speakers.
• When the front speakers are set to “Small”, the
center, surround, and front high speakers are also
automatically set to “Small”.
• If you do not use the subwoofer, the front speakers
are automatically set to “Large”.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
To output test tone from
adjacent speakers
When a test tone is not output
from the speakers
You can output test tone from adjacent
speakers so that you can adjust the balance
between the speakers.
• The speaker cords may not be connected
securely. Check to see if they are connected
securely and cannot be disconnected by
pulling on them slightly.
• The speaker cords may have the short-circuit
problem.
1 Press B/b repeatedly to select “Phase
Noise”, then press
.
2 Press V/v repeatedly to adjust the
parameter, then press
.
• OFF
• LH/FR, LH/RH, FL/RH, FL/SR, SL/FL,
SB/SL, SBL/SL, SBR/SBL, SR/SB,
SR/SBR, SR/SL, FR/SR, FR/SL,
CNT/FR, FL/CNT
Lets you output the test tone sequentially
from adjacent speakers.
Some items may not be displayed,
depending on the setting of the speaker
pattern.
3 Press V/v repeatedly to adjust the
speaker level, then press
.
To output the source sound
from adjacent speakers
You can output the source sound from
adjacent speakers so that you can adjust the
balance between the speakers.
1 Press B/b repeatedly to select “Phase
Audio”, then press
.
When a test tone is output from
a different speaker than the
speaker displayed on the TV
screen
The speaker pattern to the connected speaker
is not set up correctly. Make sure the speaker
connection and the speaker pattern match.
D.Range Comp (Dynamic range
compression)
Lets you compress the dynamic range of the
soundtrack. This may be useful when you want
to watch movies at low volumes late at night.
Dynamic range compression is possible with
Dolby Digital sources only.
x MAX
The dynamic range is compressed
dramatically.
x STD
2 Press V/v repeatedly to adjust the
parameter, then press
.
• OFF
• LH/FR, LH/RH, FL/RH, FL/SR, SL/FL,
SB/SL, SBL/SL, SBR/SBL, SR/SB,
SR/SBR, SR/SL, FR/SR, FR/SL,
CNT/FR, FL/CNT
Lets you output front 2 channel source
sound (instead of the test tone)
sequentially from adjacent speakers.
Some items may not be displayed,
depending on the setting of the speaker
pattern.
The dynamic range is compressed as intended
by the recording engineer.
x AUTO
The dynamic range is applied automatically
with Dolby TrueHD source or other source is
set to “OFF”.
x OFF
The dynamic range is not compressed.
3 Press V/v repeatedly to adjust the
speaker level, then press
.
94GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Right
Tips
• Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the
dynamic range information included in the Dolby
Digital signal.
• “STD” is the standard setting, but it only enacts
light compression. Therefore, we recommend
using the “MAX” setting. This greatly compresses
the dynamic range and lets you view movies late at
night at low volumes. Unlike analog limiters, the
levels are predetermined and provide a very natural
compression.
Distance Unit
Lets you select the unit of measure for setting
distances.
Surround Settings menu
You can adjust the sound effect on the
“S.F. Select” screen.
Note
The setup items you can adjust on each menu vary
depending on the sound field.
S.F. Select (Sound field select)
You can select the surround sound field and
adjust the effect level on the “S.F. Select”
screen.
For details on the sound field, see “Enjoying
Surround Sound” (page 65).
x FEET
The distance is displayed in feet.
x METER
The distance is displayed in meters.
To select the surround sound
field
1 Press V/v repeatedly to select
“S.F. Select”, then press
or b.
2 Press V/v repeatedly to select
surround sound you want, then press
.
“S.F. Select”, then press
or b.
2 Press V/v repeatedly to select
surround sound you want, then press
or b.
Note
Effect Level adjustment is valid only when
“Cinema St EX DCS ” is selected.
3 Press V/v repeatedly to select effect
level you want, then press
• MAX
• STD
• MIN
.
95GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
To adjust the effect level
1 Press V/v repeatedly to select
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
EQ Settings menu
Audio Settings menu
You can use the following parameters to adjust
the tonal quality (bass/trebel level) of front
speakers.
You can make settings for the audio to suit
your preference.
Bass
Treble
Level
(dB)
Frequency
(Hz)
A/V Sync (Synchronizes audio
with video output)
Lets you delay the output of audio to minimize
the time gap between audio output and visual
display. You can adjust the delay from 0 ms to
300 ms in 10 ms steps.
Notes
Notes
• This function does not work in the following cases.
– Sound Field is set to “Analog Direct”.
– Signals with a sampling frequency of more than
48 kHz are being received.
• If the equalizer is adjusted while the receiver is
receiving signals with a sampling frequency of
more than 96 kHz, the signals will always be
played back at 96 kHz.
• This parameter is useful when you use a large LCD
or plasma monitor or a projector.
• This function does not work in the following cases.
– Sound Field is set to “Analog Direct”.
– Signals with a sampling frequency of more than
96 kHz are being received.
To adjust the equalizer on the
EQ screen
1 Press B/b repeatedly to select “Bass”
or “Treble”.
2 Press V/v repeatedly to adjust the gain,
then press
.
Dual Mono (Digital broadcast
language selection)
Lets you select the language you want to listen
to during digital broadcast. This feature only
functions for Dolby Digital sources.
x Main/Sub
Sound of the main language will be output
through the front left speaker and sound of the
sub language will be output through the front
right speaker simultaneously.
x Main
Sound of the main language will be output.
x Sub
Sound of the sub language will be output.
96GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Dec. Priority (Digital audio input
decoding priority)
Lets you specify the input mode for the digital
signal input to the DIGITAL IN jacks or
HDMI IN jacks.
x AUTO
Automatically switches the input mode
between DTS, Dolby Digital, or PCM.
x PCM
When signals from the DIGITAL IN jack are
selected, PCM signals are given priority (to
prevent interruption when playback starts).
However, when other signals are input, there
may be no sound, depending on the format.
In this case, set this item to “AUTO”.
When signals from the HDMI IN jack are
selected, only PCM signals are output from the
connected player. When signals other than
PCM are received, set this item to “AUTO”.
Notes
• Even when “Dec. Priority” is set to “PCM”, the
sound may be interrupted at the very beginning of
the first track depending on the CD being played
back.
• When playback a DTS CD, set “Dec. Priority” to
“AUTO”.
masterpage: Right
Video Settings menu
You can make settings for video.
Resolution (Converting video
signals)
Lets you convert the resolution of analog video
input signals (component video and video) and
output from the HDMI TV OUT jack.
x AUTO
The resolution is set automatically, depending
on the connected TV.
x 480/576p
The resolution is set to 480p/576p. Video
signals are upconverted and output through the
receiver.
x 720p
The resolution is set to 720p. Video signals are
upconverted and output through the receiver.
x 1080i
The resolution is set to 1080i. Video signals
are upconverted and output through the
receiver.
The resolution is set to 1080p. Video signals
are upconverted and output through the
receiver.
Note
If you select a resolution that the connected TV does
not support in “Resolution” menu, the images from
the TV will not be output correctly.
97GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
x 1080p
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Comp.Dec. (Component video
decoder)
If the image is distorted when you connect to
video game, set “Comp.Dec.” to “ON”. This
setting is only applicable for component video
input signals.
x ON
x OFF
masterpage: Left
HDMI Settings menu
You can make the required settings for
components connected to the HDMI jack.
Ctrl for HDMI (Control for HDMI)
Lets you turn the Control for HDMI function
on or off. For details, see “Preparing for the
“BRAVIA” Sync” (page 70).
x ON
x OFF
Note
When you set “Ctrl for HDMI” to “ON”, “Audio
Out” may be changed automatically.
Pass Through
Lets you output the HDMI signals to the TV
even when the receiver is in standby mode.
x ON
When the receiver is in the standby mode, the
receiver continuously outputs HDMI signals
from the receiver’s HDMI TV OUT jack.
x AUTO
When the TV is turned on while the receiver is
in the standby mode, the receiver outputs
HDMI signals from the receiver’s HDMI TV
OUT jack. Sony recommends this setting if
you use a TV that is compatible with
“BRAVIA” Sync. This setting saves power in
the standby mode compared with the “ON”
setting.
x OFF
The receiver does not output HDMI signals
when in the standby mode.
Turn on the receiver to enjoy the connected
component’s source on the TV. This setting
saves power in the standby mode compared
with the “ON” setting.
98GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Notes
• This parameter is not available when “Ctrl for
HDMI” is set to “OFF”.
• When “AUTO” is selected, it may take a little more
time for the image and sound to be output to the TV
than when “ON” is selected.
• When the receiver is in standby mode,
“A.STANDBY” appears on the display if “Pass
Through” is set to “AUTO” or “ON”. However,
“A.STANDBY” will disappear when “Pass
Through” is set to “AUTO” and no signals are
detected.
Audio Out (Setting HDMI audio
input)
Lets you set the audio output for HDMI from
the playback component connected to the
receiver via an HDMI connection.
x AMP
masterpage: Right
SW Level (Subwoofer level for
HDMI)
Lets you set the level of the subwoofer to 0 dB
or +10 dB when PCM signals are input via an
HDMI connection. You can set the level for
each HDMI input independently.
x AUTO
Automatically sets the level to 0 dB or +10 dB
depending on the frequency.
x +10 dB
x 0 dB
SW L.P.F. (Subwoofer Low Pass
Filter for HDMI)
Audio signals are not output from the TV speakers
when “Audio Out” is set to “AMP”.
x ON
x TV+AMP
The low pass filter of the subwoofer’s cut off
frequency is set to 120 Hz.
The sound is output from TV’s speaker and the
speakers connected to the receiver.
x OFF
Notes
The low pass filter of the subwoofer is turned
off.
• The sound quality of the playback component
depends on the TV’s sound quality, such as the
number of channels, and the sampling frequency,
etc. When the TV has stereo speakers, the sound
output from the receiver is also stereo as that of the
TV, even if you play back multi channel source.
• When you connect the receiver to an image display
component (projector, etc.), sound may not be
output from the receiver. In this case, select
“AMP”.
• When you select the input that you have assigned
the HDMI input, sound does not output from the
TV.
99GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
Note
Lets you set the low pass filter of the
subwoofer when multi channel Linear PCM
signals are input via an HDMI connection.
Set the “SW L.P.F.” if your connected
subwoofer’s crossover frequency do not have
low pass filter.
The HDMI audio signals from the playback
component is only output to the speakers
connected to the receiver. Multi channel sound
can be played back as it is.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
ARC (Audio Return Channel)
Lets you enjoy the TV sound from the
speakers connected to the receiver via an
HDMI cable. For details, see “Enjoying the
TV sound via an HDMI cable” (page 74).
x ON
masterpage: Left
System Settings menu
You can customize the settings of the receiver.
Auto Standby
x OFF
Lets you set the receiver switch to standby
mode automatically when you do not operate
the receiver or when there is no signals input to
the receiver.
Audio signal is input to the TV OPTICAL IN
or TV AUDIO IN jack.
x ON
Audio signal is input to the HDMI TV OUT
jack.
Note
Switches to standby mode after approximately
30 minutes.
This parameter is not available when “Ctrl for
HDMI” is set to “OFF”.
x OFF
Does not switch to standby mode.
Notes
• This function does not work in the following cases.
– TUNER input is selected.
– S-AIR receiver or surround amplifier is used.
• If you use the Auto standby mode and the Sleep
Timer at the same time, the Sleep Timer has
priority.
100GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Operating without
connecting to a TV
You can operate this receiver using the display
even if you do not use a GUI when a TV is not
connected.
AMP
masterpage: Right
4
Press V/v repeatedly to select
the parameter you want to
adjust, then press
or b.
5
Press V/v repeatedly to select
the setting you want, then
press
.
To return to the previous
display
Press B or RETURN/EXIT O.
To exit the menu
Press MENU.
Note
Some parameters and settings may appear dimmed
on the display. This means that they are either
unavailable or fixed and unchangeable.
GUI MODE
V/v/B/b,
RETURN/
EXIT O
MENU
Advanced Operations
Using the menu in the display
Press GUI MODE repeatedly to
select “MENU OFF”.
When “GUI” is displayed on the display, the
menu is set to display on the TV screen using
a GUI.
1
2
3
Press AMP.
Press MENU.
Press V/v repeatedly to select
the menu you want, then press
or b.
101GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
Overview of the menus
The following options are available in each menu. For details on navigating through menus, see
page 101.
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
FULL FLAT, ENGINEER,
FRONT REF, OFF
FULL FLAT
Position
[POSITION]
POS 1, POS 2, POS 3
POS 1
Naming position
[NAME IN]
For details, see “Name Input (Naming
position)” (page 91).
Test tonea)
[TEST TONE]
OFF, FIX xxxb), AUTO xxxb)
OFF
Phase noisea)
[P. NOISE]
OFF, LH/FR, LH/RH, FL/RH,
FL/SR, SL/FL, SB/SL, SBL/SL,
SBR/SBL, SR/SB, SR/SBR, SR/SL,
FR/SR, FR/SL, CNT/FR, FL/CNT
OFF
Phase audioa)
[P. AUDIO]
OFF, LH/FR, LH/RH, FL/RH,
FL/SR, SL/FL, SB/SL, SBL/SL,
SBR/SBL, SR/SB, SR/SBR, SR/SL,
FR/SR, FR/SL, CNT/FR, FL/CNT
OFF
Front left speaker levela)
[FL LEVEL]
FL –10.0 dB to FL +10.0 dB
(0.5 dB per step)
FL 0 dB
Front right speaker levela)
[FR LEVEL]
FR –10.0 dB to FR +10.0 dB
(0.5 dB per step)
FR 0 dB
Center speaker levela)
[CNT LEVEL]
CNT –20.0 dB to CNT +10.0 dB
(0.5 dB per step)
CNT 0 dB
Surround left speaker levela)
[SL LEVEL]
SL –20.0 dB to SL +10.0 dB
(0.5 dB per step)
SL 0 dB
Surround right speaker levela)
[SR LEVEL]
SR –20.0 dB to SR +10.0 dB
(0.5 dB per step)
SR 0 dB
Surround back speaker levela)
[SB LEVEL]
SB –20.0 dB to SB +10.0 dB
(0.5 dB per step)
SB 0 dB
Surround back left speaker
levela)
[SBL LEVEL]
SBL –20.0 dB to SBL +10.0 dB
(0.5 dB per step)
SBL 0 dB
Surround back right speaker
levela)
[SBR LEVEL]
SBR –20.0 dB to SBR +10.0 dB
(0.5 dB per step)
SBR 0 dB
Front left high speaker levela)
[LH LEVEL]
LH –20.0 dB to LH +10.0 dB
(0.5 dB step)
LH 0 dB
Front right high speaker levela)
[RH LEVEL]
RH –20.0 dB to RH +10.0 dB
(0.5 dB step)
RH 0 dB
Auto Calibration Auto Calibration start
settings
[A.CAL START]
[<AUTO CAL>]
Calibration type
[CAL TYPE]
Level settings
[<LEVEL>]
102GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Menu
[Display]
Speaker settings
[<SPEAKER>]
masterpage: Right
Settings
Initial
setting
Subwoofer levela)
[SW LEVEL]
SW –20.0 dB to SW +10.0 dB
(0.5 dB per step)
SW 0 dB
Dynamic range compression
[D. RANGE]
COMP. MAX, COMP. STD,
COMP. AUTO, COMP. OFF
COMP. AUTO
Speaker pattern
[SP PATTERN]
5/2.1, 5/2, 4/2.1, 4/2, 3/4.1, 3/4, 2/4.1, 3/4.1
2/4, 3/3.1, 3/3, 2/3.1, 2/3, 3/2.1, 3/2,
2/2.1, 2/2, 3/0.1, 3/0, 2/0.1, 2/0
Front speakers sizea)
[FRT SIZE]
LARGE, SMALL
LARGE
Center speaker sizea)
[CNT SIZE]
LARGE, SMALL
LARGE
Surround speakers sizea)
[SUR SIZE]
LARGE, SMALL
LARGE
Front high speakers sizea)
[FH SIZE]
LARGE, SMALL
LARGE
Surround back speaker assignc)
[SB ASSIGN]
SPK B, BI-AMP, OFF
OFF
Front left speaker distancea)
[FL DIST.]
FL 3’3” to FL 32’9”
(FL 1.00 m to FL 10.00 m)
(1 inch (0.01 m) step)
FL 9’10”
(FL 3.00 m)
Front right speaker distancea)
[FR DIST.]
FR 3’3” to FR 32’9”
(FR 1.00 m to FR 10.00 m)
(1 inch (0.01 m) step)
FR 9’10”
(FR 3.00 m)
Center speaker distancea)
[CNT DIST.]
CNT 3’3” to CNT 32’9”
(CNT 1.00 m to CNT 10.00 m)
(1 inch (0.01 m) step)
CNT 9’10”
(CNT 3.00 m)
Surround left speaker distancea)
[SL DIST.]
SL 3’3” to SL 32’9”
(SL 1.00 m to SL 10.00 m)
(1 inch (0.01 m) step)
SL 9’10”
(SL 3.00 m)
Surround right speaker distancea) SR 3’3” to SR 32’9”
[SR DIST.]
(SR 1.00 m to SR 10.00 m)
(1 inch (0.01 m) step)
SR 9’10”
(SR 3.00 m)
Surround back speaker distancea) SB 3’3” to SB 32’9”
[SB DIST.]
(SB 1.00 m to SB 10.00 m)
(1 inch (0.01 m) step)
SB 9’10”
(SB 3.00 m)
Surround back left speaker
distancea)
[SBL DIST.]
SBL 3’3” to SBL 32’9”
(SBL 1.00 m to SBL 10.00 m)
(1 inch (0.01 m) step)
SBL 9’10”
(SBL 3.00 m)
Surround back right speaker
distancea)
[SBR DIST.]
SBR 3’3” to SBR 32’9”
(SBR 1.00 m to SBR 10.00 m)
(1 inch (0.01 m) step)
SBR 9’10”
(SBR 3.00 m)
Front left high speaker distancea)
[LH DIST.]
LH 3’3” to LH 32’9”
(LH 1.00 m to LH 10.00 m)
(1 inch (0.01 m) step)
LH 9’10”
(LH 3.00 m)
Front right high speaker distancea) RH 3’3” to RH 32’9”
[RH DIST.]
(RH 1.00 m to RH 10.00 m)
(1 inch (0.01 m) step)
RH 9’10”
(RH 3.00 m)
continued
103GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
Parameters
[Display]
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
Subwoofer distancea)
[SW DIST.]
SW 3’3” to SW 32’9”
(SW 1.00 m to SW 10.00 m)
(1 inch (0.01 m) step)
SW 9’10”
(SW 3.00 m)
Distance unit
[DIST. UNIT]
FEET, METER
FEETd)
Front speaker crossover
frequencye)
[FRT CROSS]
CROSS 40 Hz to CROSS 200 Hz
(10 Hz step)
CROSS 120 Hz
Center speaker crossover
frequencye)
[CNT CROSS]
CROSS 40 Hz to CROSS 200 Hz
(10 Hz step)
CROSS 120 Hz
Surround speaker crossover
frequencye)
[SUR CROSS]
CROSS 40 Hz to CROSS 200 Hz
(10 Hz step)
CROSS 120 Hz
Front high speaker crossover
frequencye)
[FH CROSS]
CROSS 40 Hz to CROSS 200 Hz
(10 Hz step)
CROSS 120 Hz
Surround settings Sound field selection
[<SURROUND>] [S.F. SELECT]
EQ settings
[<EQ>]
Tuner settings
[<TUNER>]
masterpage: Left
For details, see “Enjoying Surround MULTI ST. j)
Sound” (page 65).
Effect levelf)
[EFFECT]
EFCT. MAX, EFCT. STD,
EFCT. MIN
EFCT. STD
Front speakers bass level
[BASS]
BASS –10 dB to BASS +10 dB
(1 dB per step)
BASS 0 dB
Front speakers treble level
[TREBLE]
TREBLE –10 dB to TREBLE
+10 dB (1 dB per step)
TREBLE 0 dB
FM station receiving mode
[FM MODE]
STEREO, MONO
STEREO
Naming preset stations
[NAME IN]
For details, see “Naming preset
stations (Name Input)” (page 56).
Parental lockg)
[PARENTAL]
LOCK ON, LOCK OFF
Lock code editg)
[CODE EDIT]
For details, see “Restricting access to
specific channels (Parental Lock)”
(page 62).
SIRIUS antenna aiming modeg)
[SR ANT AIM]
For details, see “Checking receiving
conditions (Antenna Aiming)”
(page 59).
SIRIUS radio IDg)
[SIRIUS ID]
For details, see “Checking the
SIRIUS Radio ID” (page 58).
LOCK OFF
104GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Right
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
Audio settings
[<AUDIO>]
Synchronizes audio with video
output
[A/V SYNC]
0 ms to 300 ms
(10 ms per step)
0 ms
Digital broadcast language
selection
[DUAL MONO]
MAIN/SUB, MAIN, SUB
MAIN
Digital audio input decoding
priority
[DEC. PRIO.]
DEC. AUTO, DEC. PCM
DEC. AUTO
Digital audio input assignment
[A. ASSIGN]
For details, see “Enjoying the sound/
images from other inputs” (page 85).
Resolution
[RESOLUTION]
AUTO, 480/576p, 720p, 1080i,
1080p
Video input assignment
[V. ASSIGN]
For details, see “Enjoying the sound/
images from other inputs” (page 85).
Switching component signals
[COMP. DEC.]
DEC. ON, DEC. OFF
DEC. OFF
Control for HDMI
[CTRL:HDMI]
CTRL ON, CTRL OFF
CTRL ON
HDMI Pass Through
[PASS THRU]
ON, AUTO, OFF
OFF
Setting HDMI audio input
[AUDIO OUT]
AMP, TV+AMP
AMP
Subwoofer level for HDMIh)
[SW LEVEL]
SW AUTO, SW +10 dB, SW 0 dB
SW AUTO
Subwoofer Low Pass Filter for
HDMIh)
[SW L.P.F.]
L.P.F. ON, L.P.F. OFF
L.P.F. ON
Audio Return Channel
[ARC]
ARC ON, ARC OFF
ARC ON
Brightness of the display
[DIMMER]
DIM MAX, DIM MID, DIM OFF
DIM OFF
Auto standby mode
[AUTO STBY]
STBY ON, STBY OFF
STBY ON
Naming inputs
[NAME IN]
For details, see “Name Input”
(page 47).
Video settings
[<VIDEO>]
HDMI settings
[<HDMI>]
continued
105GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
System settings
[<SYSTEM>]
AUTO
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
masterpage: Left
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
S-AIR settings
[<S-AIR>]
S-AIR IDi)
[S-AIR ID]
ID: A, ID: B, ID: C
ID: A
Pairingi)
[PAIRING]
START, CONDITION
START
S-AIR modei)
[S-AIR MODE]
PARTY, SEPARATE
PARTY
RF Changei)
[RF CHANGE]
RF AUTO, RF ON, RF OFF
RF AUTO
S-AIR Standbyi)
[S-AIR STBY]
STBY ON, STBY OFF
STBY OFF
a)
Depends on the speaker pattern setting, some parameters or settings may not be available.
represent a speaker channel (FL, FR, CNT, SL, SR, SB, SBL, SBR, LH, RH, SW).
c) You can only select this parameter if “SP PATTERN” is not set to a setting with surround back or front high
speakers (page 91).
d) “METER” for models of area code CEK, ECE, AU1 and TW2.
e) You can only select this parameter if your speaker is set to “SMALL”.
f)
You can only select this parameter if you select Cinema Studio A/B/C as sound field.
g) This parameter is only available if the SiriusConnect Home tuner is connected to the SIRIUS jack on the
receiver.
h)
This parameter is only available when HDMI input is selected.
i) This parameter is only available if the S-AIR transmitter (not supplied) is inserted to the EZW-T100 slot on
the receiver.
j)
“A.F.D. AUTO” for models of area code CEK, ECE, AU1 and TW2.
b) xxx
106GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Performing Auto Calibration
For details on the Auto Calibration, see
“Calibrating the appropriate speaker settings
automatically (Auto Calibration)” (page 38).
See “Before you perform Auto Calibration”
(page 38) before performing the Auto
Calibration.
To operate on the receiver
1 Press GUI MODE repeatedly to select
“MENU OFF”.
2 Press AMP.
Receiver operation is enabled.
3 Press MENU.
4 Press V/v repeatedly to select “<AUTO
CAL>” , then press
or b.
masterpage: Right
To cancel Auto Calibration
The Auto Calibration function will be
canceled when you do the following during the
measurement process:
– Press ?/1.
– Press the input buttons on the remote or
press the INPUT SELECTOR +/–
repeatedly on the receiver.
– Press MUTING (RM-AAP051 only) or
(RM-AAP052 only) on the remote. You can
also use MUTING on the receiver.
– Press SPEAKERS on the receiver.
– Change the volume level.
– Connect the headphones.
Tips
• Operations other than turning the receiver on or off
are deactivated during Auto Calibration.
• The measurements may not be performed correctly
or Auto Calibration cannot be performed when
special speakers, such as dipole speakers are used.
5 Press V/v repeatedly to select “A.CAL
START”, then press
to start the
measurement.
Measurement starts in 5 seconds. A count
down is displayed.
Note
While the time is counting down, stand away
from the measurement area to avoid
measurement error.
The measurement process will take
approximately 30 seconds. Wait until the
measurement process completes.
When the measurement ends, a beep
sounds and the measurement result appears
on the display.
Measurement process Explanation
[Display]
Completes properly
[SAVE EXIT]
Proceed to step 2.
Fails
[E - xxxa):xxb)]
See “Message list
after Auto
Calibration
measurement”
(page 43).
a) xxx
F
S
SB
FH
represent a speaker channel.
Front
Surround
Surround back
Front high
Depending on the error code, the speaker
channel may not appears.
b) xx represent an error code.
continued
107GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
6 Measurement starts.
To confirm/save Auto
Calibration results when GUI
function is turned off
1 Confirm the measurement result.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
2 View the measurement result.
Press AMP and then press V/v repeatedly
to select the item. Then press
.
Item and explanation
EXIT
Exits the setting process without saving the
measurement results.
LEVEL INFO.
Displays the measurement result for speaker
level.
masterpage: Left
5 Disconnect the optimizer microphone
after you have finished.
Note
If you have reposition your speaker, we recommend
that you perform Auto Calibration again to enjoy the
surround sound.
Tip
PHASE INFO.
Displays the phase of each speaker (in phase/out
of phase). See “When you select “PHASE
INFO.”” (page 108).
The size of a speaker (LARGE/SMALL) is
determined by the low frequency characteristics.
The measurement results may vary, depending on
the position of the optimizer microphone and
speakers, and the shape of the room. It is
recommended that you follow the measurement
results. However, you can change those settings in
the Speaker Settings menu. Save the measurement
results first, then try to change the settings if you
want.
WARN CHECK
Displays warning concerning the measurement
results. See “Message list after Auto Calibration
measurement” (page 43).
When you select “PHASE
INFO.”
DIST. INFO.
Displays the measurement result for speaker
distance.
SAVE EXIT
Saves the measurement results and exits the
setting process.
RETRY
Performs the Auto Calibration again.
You can check the phase of each speaker
(in phase/out of phase).
1 Press V/v repeatedly to select a
speaker you want to check.
Display and explanation
3 Save the measurement result.
Select “SAVE EXIT” in step 2.
“COMPLETE” appears on the display and
the settings are registered as selected
position number.
4 Select the calibration type.
Press V/v repeatedly to select CAL TYPE,
then press
.
Calibration type and explanation
FULL FLAT
Makes the measurement of frequency from each
speaker flat.
ENGINEER
Sets the frequency characteristics to a set that
matches that of the Sony listening room
standard.
FRONT REF
Adjusts the characteristics of all the speakers to
match the characteristics of the front speaker.
OFF
Set the Auto Calibration to off.
xxx* : IN
The speaker is in phase.
xxx* : OUT
The speaker is out of phase. The “+” and “–”
terminals of the speaker may be connected the
other way around. However, depending on the
speakers, “xxx:OUT” appears on the display
even though the speakers are connected
properly. This is because of the speakers’
specifications. In this case, you can continue to
use the receiver.
* xxx
FL
FR
CNT
SL
SR
SBL
SBR
LH
RH
SW
represent a speaker channel.
Front left
Front right
Center
Surround left
Surround right
Surround back left
Surround back right
Front left high
Front right high
Subwoofer
Depending on the measurement result, the
speaker channel may not appears.
108GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
2 Press
to return to step 2 in “To
confirm/save Auto Calibration results
when GUI function is turned off” (page
107).
Presetting radio stations
1
Tip
Depending on the position of the subwoofer, the
measurement results for polarity may vary.
However, there will be no problems even if you
continue to use the receiver with that value.
2
3
4
press D.TUNING.
2 Press SHIFT, then press numeric
buttons to enter the frequency.
3 Press
.
5
Repeat steps 1 to 4 to preset
another station.
Selecting a preset station
1 Press TUNER repeatedly to select the
FM or AM band.
2 Press PRESET + or PRESET –
repeatedly to select the preset station
you want.
You can also press SHIFT, then press
numeric buttons to select the preset station
you want. Then, press
to enter the
selection.
109GB
STR-DN1010
4-174-068-11(1)
Advanced Operations
Selecting a frequency directly
(Direct Tuning)
1 After selecting the FM or AM band,
Press ENTER.
If SHIFT indicator is light off before you
press ENTER, press SHIFT.
The station is stored as the selected preset
number.
If “MEM” disappears before you press
ENTER, start again from step 2.
FM or AM band.
You can also use INPUT SELECTOR +/–
on the receiver.
Press TUNING + to scan from low to high
frequencies, press TUNING – to scan from
high to low frequencies. The receiver stops
scanning whenever a station is received.
Press PRESET + or PRESET –
to select a preset number.
30 FM and 30 AM preset numbers are
available. If “MEM” disappears before
you select the preset number, start again
from step 2.
For details on the tuner function, see “Tuner
Operations” (page 53).
2 Press TUNING + or TUNING –.
Press SHIFT, then press
MEMORY.
“MEM” lights up for a few seconds.
Perform steps 3 and 4 before “MEM”
disappears.
Listening to the FM/AM radio
Tuning radio stations
1 Press TUNER repeatedly to select the
Tune in the station that you
want to preset.
For details on the operation, see “Tuning
radio stations” (page 109).
Selecting a sound field type
For details on each sound field type, see
“Enjoying Surround Sound” (page 65).
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Listening to satellite tuner
(Models of area code U2, CA2
only)
For details on SIRIUS Radio service, see
“Listening to Satellite Radio” (page 57) in
“Tuner Operations”.
Aiming the SIRIUS Antenna
You can use “SR ANT AIM” in the Tuner
Settings menu to help you aim the antenna for
optimal signal reception.
1 Press TUNER repeatedly to select
“SIRIUS”.
You can also use INPUT SELECTOR +/–
on the receiver.
2 Press AMP.
3 Press MENU.
“<TUNER>”.
or b to enter the menu.
6 Press V/v repeatedly to select
“SR ANT AIM”.
7 Press
or b to enter the parameter.
8 While checking the parameter, aim
your antenna to where the best
reception will be received.
For details on the parameter, see “SIRIUS
Signal strength” below.
“SIRIUS”.
You can also use INPUT SELECTOR +/–
on the receiver.
2 Press TUNING + or TUNING – to select
channel 0.
3 Check the SIRIUS ID on the display
and write it in the space provided here.
SIRIUS ID:___________________________
Selecting channels from a
category (CATEGORY TUNING)
1 Press TUNER repeatedly to select
“SIRIUS”.
You can also use INPUT SELECTOR +/–
on the receiver.
to select “ONE CAT”.
• ALL CAT: You can select a channel from
all the categories. The initial setting is
“ALL CAT”.
• ONE CAT: You can select a channel from
one category. “CAT” lights up on the
display when you set to “ONE CAT”
mode.
3 Press CATEGORY + or CATEGORY –
to select the category you want.
The category is selected and the channel
with the lowest number in the specified
category is selected.
4 Press TUNING + or TUNING – to select
SIRIUS Signal strength
Signal
strength
Checking the SIRIUS Radio ID
1 Press TUNER repeatedly to select
2 Press CATEGORY MODE repeatedly
4 Press V/v repeatedly to select
5 Press
masterpage: Left
the channel.
Signal type
Satellite
Terrestrial
EXC (excellent)
S:3
T:3
GOOD
S:2
T:2
WEAK
S:1
T:1
NONE
S:0
T:0
Selecting a channel number
directly (Direct Tuning)
1 After selecting satellite tuner, press
D.TUNING.
2 Press SHIFT, then press numeric
buttons to enter the channel number.
3 Press
.
110GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm
Presetting satellite tuner
channels (Models of area code
U2, CA2 only)
1
2
Select a channel you want to
preset.
Changing the brightness of the
front panel display (DIMMER)
You can change the brightness of the front
panel display.
Press AMP.
For details on this operation, see
“Selecting channels from a category
(CATEGORY TUNING)” (page 110).
1
2
3
Press SHIFT, then press
MEMORY.
4
Press V/v repeatedly to select
“DIMMER”, then press
or b.
5
Press V/v repeatedly to select
the setting you want, then
press
.
“MEM” lights up on the display.
3
Press PRESET + or PRESET –
to select a preset number.
You can also select the number by
pressing SHIFT, then numeric buttons.
Preset numbers from 1 to 30 are available.
Channel 1 is preset for the preset numbers
when you purchase the receiver.
4
Press MEMORY.
If SHIFT indicator is light off before you
press MEMORY, press SHIFT.
“MEM” lights off.
Press MENU.
Press V/v repeatedly to select
“SYSTEM”, then press
or b.
The front panel display will change the
brightness according to the setting you
have selected.
Tip
You can also use DIMMER on the receiver to
change the brightness of the front panel display.
Repeat steps 1 to 4 to preset
another channel.
Advanced Operations
5
masterpage: Right
Selecting a preset channel
1 Press TUNER repeatedly to select
“SIRIUS”.
2 Press PRESET + or PRESET –
repeatedly to select the preset channel
you want.
You can also press SHIFT, then numeric
buttons to select the preset channel you
want. Then, press
to enter the selection.
111GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB06REM_STR-DN1010-CEL.fm
3
Using the Remote
Programming the remote
You can customize the remote to match the
components connected to your receiver. You
can even program the remote to control nonSony components and also Sony components
that the remote is normally unable to control.
Before you begin, note that:
– You cannot change the settings of DMPORT
input buttons.
– The remote can control only components
that accept infrared wireless control signals.
Be sure to turn on the receiver and
point the remote towards the
receiver when performing the
following procedure.
RM
SET UP
SHIFT
See the tables on page 113–116 for
information on the numeric code(s).
Note
For a TV remote code value, only numbers in
the 500’s are valid.
4
Press ENTER.
Once the numeric code has been verified,
the RM SET UP indicator slowly flashes
twice and the remote automatically exits
the programming mode.
5
Repeat steps 1 to 4 to control
other components.
Notes
TV
• The indicator turns off while a valid button is
pressed.
• In step 2, if you press TUNER, you can only
program the button to control a tuner (page 113).
• For the numeric codes, only the last three numbers
entered are valid.
Input
buttons
ENTER
Press and hold RM SET UP,
then press AV ?/1.
The RM SET UP indicator flashes slowly.
2
Press numeric buttons to enter
the numeric code (or one of the
codes if more than one code
exists) corresponding to the
component and the maker of
the component you want to
control (including TV button).
AV ?/1
Numeric
buttons
1
masterpage: Left
Press the input button for the
component you want to control.
To cancel programming
Press RM SET UP during any step. The RM
SET UP indicator flashes 5 times in quick
succession. The remote automatically exits the
programming mode.
To activate the input after
programming
Press the programmed button to activate the
input you want.
For example, if you are going to control a
VCR connected to VIDEO 1 IN, press
VIDEO 1.
The RM SET UP and SHIFT indicator
light up.
112GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB06REM_STR-DN1010-CEL.fm
If programming is
unsuccessful, check the
following:
• If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
• If the indicator flashes 5 times in quick
succession while entering the numeric code,
an error has occurred.
Start again from step 1.
The numeric codes
corresponding to the component
and the maker of the component
Use the numeric codes in the tables below to
control non-Sony components and also Sony
components that the remote is normally unable
to control. Since the remote signal that a
component accepts differs depending on the
model and year of the component, more than
one numeric code may be assigned to a
component. If you fail to program your remote
using one of the codes, try using other codes.
masterpage: Right
To control a tuner
Maker
Code(s)
SONY
005
To control a CD player
Maker
Code(s)
SONY
101, 102, 103
DENON
104, 123
JVC
105, 106, 107
KENWOOD
108, 109, 110
MAGNAVOX
111, 116
MARANTZ
116
ONKYO
112, 113, 114
PANASONIC
115
PHILIPS
116
PIONEER
117
TECHNICS
115, 118, 119
YAMAHA
120, 121, 122
To control a DAT deck
Maker
Code(s)
Notes
SONY
203
• The numeric codes are based on the latest
information available for each brand. There is a
chance, however, that your component will not
respond to some or all of the codes.
• All of the input buttons on this remote may not be
available when used with your particular
component.
PIONEER
219
To control a tape deck
Maker
Code(s)
SONY
201, 202
DENON
204, 205
206, 207, 208, 209
NAKAMICHI
210
PANASONIC
216
PHILIPS
211, 212
PIONEER
213, 214
TECHNICS
215, 216
YAMAHA
217, 218
continued
113GB
STR-DN1010
4-174-068-11(1)
Using the Remote
KENWOOD
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB06REM_STR-DN1010-CEL.fm
masterpage: Left
To control an MD deck
To control a DVD recorder
Maker
Code(s)
Maker
Code(s)
SONY
301
SONY
401, 402, 403
DENON
302
JVC
303
To control a DVD/VCR COMBO
KENWOOD
304
Maker
Code(s)
SONY
411
To control an HDD recorder
Maker
SONY
Code(s)
307, 308, 309
To control a Blu-ray disc player/
recorder
Maker
Code(s)
SONY
310, 311, 312
PANASONIC
335
SAMSUNG
336
LG
337
To control a PSX
To control a DVD/HDD COMBO
Maker
Code(s)
SONY
401, 402, 403
To control a TV
Maker
Code(s)
SONY
501, 502
AIWA
501, 536, 539
AKAI
503
AOC
503
CENTURION
566
CORONADO
517
Maker
Code(s)
CURTIS-MATHES
503, 551, 566, 567
SONY
313, 314, 315
DAYTRON
517, 566
DAEWOO
504, 505, 506, 507,
515, 544
Code(s)
FISHER
508, 545
401, 402, 403
FUNAI
548
424
FUJITSU
528
DENON
405
GOLDSTAR/LG
HITACHI
416
503, 512, 515, 517,
534, 544, 556, 568
JVC
415, 423
GRUNDIG
511, 533, 534
MITSUBISHI
419
HITACHI
ORITRON
417
503, 513, 514, 515,
517, 519, 544, 557,
571
PANASONIC
406, 408, 425
ITT/NOKIA
521, 522
503, 510, 566
To control a DVD player
Maker
SONY
BROKSONIC
407
J.C.PENNY
PIONEER
409, 410
JVC
516, 552
RCA
414
KMC
517
SAMSUNG
416, 422
MAGNAVOX
TOSHIBA
404, 421
503, 515, 517, 518,
544, 566
ZENITH
418, 420
PHILIPS
MARANTZ
527
MITSUBISHI/MGA
503, 519, 527, 544,
566, 568
114GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB06REM_STR-DN1010-CEL.fm
masterpage: Right
Maker
Code(s)
To control an LD player
NEC
503, 517, 520, 540,
544, 554, 566
Maker
Code(s)
SONY
601, 602, 603
PIONEER
606
NORDMENDE
530, 558
NOKIA
521, 522, 573, 575
PANASONIC
509, 524, 553, 559,
572
To control a Video CD player
PHILIPS
515, 518, 557, 570,
571
Maker
Code(s)
SONY
605
PHILCO
503, 504, 514, 517,
518
PIONEER
509, 525, 526, 540,
551, 555
PORTLAND
503
QUASAR
509, 535
RADIO SHACK
503, 510, 527, 565,
567
RCA/PROSCAN
503, 510, 523, 529,
544
SAMSUNG
503, 515, 517, 531,
532, 534, 544, 556,
557, 562, 563, 566,
569
SAMPO
566
SABA
530, 537, 547, 549,
558
To control a VCR
Maker
Code(s)
SONY
701, 702, 703, 704,
705, 706
AIWA*
710, 750, 757, 758
AKAI
707, 708, 709, 759
BLAUPUNKT
740
EMERSON
711, 712, 713, 714,
715, 716, 750
FISHER
717, 718, 719, 720
GENERAL ELECTRIC
(GE)
721, 722, 730
GOLDSTAR/LG
723, 753
HITACHI
722, 725, 729, 741
717
508, 545, 546, 560,
567
JVC
726, 727, 728, 736
SCOTT
503, 566
MAGNAVOX
730, 731, 738
SEARS
503, 508, 510, 517,
518, 551
MITSUBISHI/MGA
732, 733, 734, 735
NEC
736
517, 535, 550, 561,
565
PANASONIC
729, 730, 737, 738,
739, 740
SYLVANIA
503, 518, 566
PHILIPS
729, 730, 731
THOMSON
530, 537, 547, 549
PIONEER
729
TOSHIBA
535, 539, 540, 541,
551
RCA/PROSCAN
722, 729, 730, 731,
741, 747
TELEFUNKEN
530, 537, 538, 547,
549, 558
SAMSUNG
742, 743, 744, 745
SANYO
717, 720, 746
SHARP
748, 749
TOSHIBA
747, 756
ZENITH
754
SHARP
TEKNIKA
517, 518, 567
WARDS
503, 517, 566
YORK
566
ZENITH
542, 543, 567
GE
503, 509, 510, 544
LOEWE
515, 534, 556
* If an AIWA VCR does not work even though you
enter the code for AIWA, enter the code for Sony
instead.
continued
115GB
STR-DN1010
4-174-068-11(1)
Using the Remote
SANYO
ITT/NOKIA
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB06REM_STR-DN1010-CEL.fm
masterpage: Left
To control a satellite tuner
Maker
Code(s)
SONY
801, 802, 803, 804,
824, 825, 865
AMSTRAD
845, 846
BskyB
862
GENERAL ELECTRIC
(GE)
866
GRUNDIG
859, 860
HUMAX
846, 847
THOMSON
857, 861, 864, 876
PACE
848, 849, 850, 852,
862, 863, 864
PANASONIC
818, 855
PHILIPS
856, 857, 858, 859,
860, 864, 874
NOKIA
851, 853, 854, 864
RCA/PROSCAN
866, 871
BITA/HITACHI
868
HUGHES
867
JVC/Echostar/Dish
Network
873
MITSUBISHI
872
SAMSUNG
875
TOSHIBA
869, 870
Clearing all the contents
of the remote’s memory
1 While holding down MASTER
VOL – (RM-AAP051 only) or
2 – (RM-AAP052 only), press
and hold ?/1, then press
AV ?/1.
The RM SET UP indicator flashes 3
times.
2
Release all buttons.
All the contents of the remote’s memory
(i.e., all the programmed data) are
cleared.
To control a cable box
Maker
Code(s)
SONY
821, 822, 823
HAMLIN/REGAL
836, 837, 838, 839,
840
JERROLD/G.I./
MOTOROLA
806, 807, 808, 809,
810, 811, 812, 813,
814, 819
JERROLD
830, 831
OAK
841, 842, 843
PANASONIC
816, 826, 832, 833,
834, 835
PHILIPS
830, 831
PIONEER
828, 829
RCA
805
SCIENTIFIC ATLANTA 815, 816, 817, 844
TOCOM/PHILIPS
830, 831
ZENITH
826, 827
116GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
masterpage: Right
x Crossover frequency
Additional Information
Glossary
x Cinema Studio EX
A surround sound mode that can be regarded
as the compilation of Digital Cinema Sound
technology, delivers the sound of a dubbing
theater using three technologies: “Virtual
Multi Dimensions”, “Screen Depth
Matching”, and “Cinema Studio
Reverberation”.
“Virtual Multi Dimensions”, the virtual
speaker technology, creates a virtual multisurround environment with actual speakers up
to 7.1 channel, and brings the surround sound
experience of a theater with the latest facilities
into your home.
“Screen Depth Matching” reproduces treble
attenuation, fullness, and depth of sound
usually created in a theater using sound
emission from behind the screen. This is then
added to the front and center channels.
“Cinema Studio Reverberation” reproduces
the sound characteristics of state-of-the-art
dubbing theaters and recording studios,
including Sony Pictures Entertainment’s
dubbing studios. There are three modes, A/B/
C, available according to the studio type.
x Component video
x Deep Color (Deep Colour)
Video signals for which the color depth of
signals passing through an HDMI jack have
been raised.
The number of colors that could be expressed
by 1 pixel was 24 bits (16,777,216 colors) with
the current HDMI jack. However, the number
of colors which can be expressed by 1 pixel
will be 36, etc., bits when the receiver
corresponds to Deep Color (Deep Colour).
Since the gradation of the depth of a color can
be expressed more finely with more bits,
continuous color changes can be more
smoothly expressed.
x Digital Cinema Sound (DCS)
Unique sound reproduction technology for
home theater developed by Sony, in
cooperation with Sony Pictures Entertainment,
for enjoying the exciting and powerful sound
of movie theaters at home. With this “Digital
Cinema Sound” developed by integrating a
DSP (Digital Signal Processor) and measured
data, the ideal sound field intended by
filmmakers can be experienced at home.
x Dolby Digital
Digital audio encoding/decoding technology
developed by Dolby Laboratories, Inc. It
consists of front (left/right), center, surround
(left/right) and subwoofer channels. It is a
designated audio standard for DVD video and
also known as 5.1 channel surround. Since
surround information is recorded and
reproduced in stereo, more realistic sound with
fuller presence is delivered than with Dolby
surround.
x Composite video
A standard format for transmitting video
signal information. The luminance signal Y
and chrominance signal C are combined and
transmitted together.
continued
117GB
STR-DN1010
4-174-068-11(1)
Additional Information
A format for transmitting video signal
information consisting of three separate
signals: luminance Y, chrominance Pb, and
chrominance Pr. High quality pictures, such as
DVD video or HDTV pictures, are transmitted
more faithfully. The three jacks are color coded green, blue and red.
The frequency at which two speaker’s
frequencies intersect.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
x Dolby Digital Plus
Dolby Digital Plus provides the flexibility and
efficiency to deliver more channels of
compelling surround sound for high-definition
video media. Its superior coding efficiencies
enable up to 7.1 channel of high-quality multi
channel audio without negatively impacting
bit budgets allocated for video performance or
additional feature sets.
masterpage: Left
x Dolby Surround (Dolby Pro
Logic)
Audio processing technology developed by
Dolby Laboratories, Inc. Center and mono
surround information is matrixed into two
stereo channels. When reproduced, audio is
decoded and output in 4 channels surround
sound. This is the most common audio
processing method for DVD video.
x Dolby Digital Surround EX
x Dolby TrueHD
Acoustic technology developed by Dolby
Laboratories, Inc. Surround back information
is matrixed into regular left and right surround
channels so that the sound can be reproduced
in 6.1 channel. Active scenes, especially, are
recreated with a more dynamic and realistic
sound field.
Dolby TrueHD is Dolby’s lossless audio
technology developed for high-definition
optical discs. Dolby TrueHD audio is bit-forbit identical to the original studio masters and
provides supreme-quality audio up to 8
channel at 96 kHz/24 bit and up to 6 channel at
192 kHz/24 bit. Together with high-definition
video, it offers an unprecedented home theater
experience.
x Dolby Pro Logic II
This technology converts 2 channel stereo
recorded audio into 5.1 channel for playback.
There is a MOVIE mode for movies and
MUSIC mode for stereo sources such as
music. Old movies encoded in the traditional
stereo format can be enhanced with 5.1
channel surround sound.
x DTS 96/24
A high sound quality digital signal format. It
records audio at a sampling frequency and bit
rate of 96 kHz/24bit which is the highest
possible for DVD video. The number of
playback channels varies depending on the
software.
x Dolby Pro Logic IIx
Technology for 7.1 channel (or 6.1 channel)
playback. Along with audio encoded in Dolby
Digital Surround EX, 5.1 channel Dolby
Digital encoded audio can be reproduced in
7.1 channel (or 6.1 channel). Furthermore,
existing stereo recorded content can also be
reproduced in 7.1 channel (or 6.1 channel).
x DTS Digital Surround
Digital audio encoding/decoding technology
for theaters developed by DTS, Inc. It
compresses audio less than Dolby Digital,
delivering a higher quality sound
reproduction.
x DTS-ES
x Dolby Pro Logic IIz
Dolby Pro Logic IIz brings a vertical aspect to
the sound field through the addition of left and
right front high speakers. It decodes
nondirectional elements in the audio mix and
reproduces them from the high speakers,
giving an enhanced sense of depth and airiness
to the sound field.
Format for 6.1 channel playback with
surround back information. There are two
modes, “Discrete 6.1” which records all
channels independently, and “Matrix 6.1”
which matrixes surround back channel into
surround left and surround right channels. It is
ideal for playback of motion picture
soundtracks.
118GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
masterpage: Right
x DTS-HD
x Interlace
Audio format which extends the conventional
DTS Digital Surround format.
This format consists of a core and an
extension, and the core part has DTS Digital
Surround compatibility. There are two kinds of
DTS-HD, DTS-HD High Resolution Audio
and DTS-HD Master Audio. DTS-HD High
Resolution Audio has a maximum
transmission rate of 6 Mbps, with lossy
compression (Lossy), and DTS-HD High
Resolution Audio corresponds to a maximum
sampling frequency of 96 kHz, and a
maximum of 7.1 channel. DTS-HD Master
Audio has the maximum transmission rate of
24.5 Mbps, and uses lossless compression
(Lossless), and DTS-HD Master Audio
corresponds to a maximum sampling
frequency of 192 kHz, and a maximum of
7.1 channel.
A scanning method which completes a picture
by displaying half of the lines on a tube surface
of a TV or monitor each 1/60 second. First, all
the odd-numbered lines are drawn, leaving
spaces between each line, then all the evennumbered lines are drawn to fill the spaces.
“i” of “480i” stands for “Interlace”.
x DTS Neo:6
A scanning method that draws all scanning
lines sequentially, as opposed to interlaced
scanning where all the odd and then all the
even lines are drawn.
“p” of “480p” stands for “Progressive”.
This technology converts 2 channel stereo
recorded audio for 7 channel playback. There
are two modes to select according to the
playback source or your preference, CINEMA
for movies, and MUSIC for stereo sources
such as music.
x HDMI (High-Definition
Multimedia Interface)
x High Bitrate Audio
It refers to the audio formats of the
compression method (DTS-HD Master Audio,
Dolby TrueHD, etc.) which is a high bitrate
format recorded mainly on Blu-ray disc etc.
Sound effects of low frequencies which are
output from a subwoofer in Dolby Digital or
DTS, etc. By adding a deep bass with a
frequency between 20 to 120 Hz, audio
becomes more powerful.
x PCM (Pulse Code Modulation)
A method of converting analog audio to digital
audio for easy enjoyment of digital sound.
x Progressive
x S-AIR (Sony Audio Interactive
Radio frequency)
Recent times have seen the rapid spread of
DVD media, Digital Broadcasting, and other
high quality media.
To ensure that the subtle nuances of these high
quality media are transmitted with no
deterioration, Sony has developed a
technology called “S-AIR” for the radio
transmission of digital audio signals with no
compression, and has incorporated this
technology into the EZW-RT10/EZW-T100.
This technology transfers digital audio signals
with no compression using the 2.4 GHz band
range of ISM band (Industrial, Scientific, and
Medical band), such as wireless LANs and
Bluetooth applications.
continued
119GB
STR-DN1010
4-174-068-11(1)
Additional Information
HDMI (High-Definition Multimedia
Interface) is an interface that supports both
video and audio on a single digital connection,
allowing you to enjoy high quality digital
picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital
Contents Protection), a copy protection
technology that incorporates coding
technology for digital video signals.
x LFE (Low Frequency Effects)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
masterpage: Left
x Sampling frequency
To convert analog audio to digital, analog data
should be quantified. This process is called
sampling, and the number of times per second
the analog data is quantified is called the
sampling frequency. A standard music CD
stores data quantified at 44,100 times per
second, which is expressed as a sampling
frequency of 44.1 kHz. Generally speaking, a
higher sampling frequency means better sound
quality.
Precautions
x TSP (Time Stretched Pulse)
• Before operating the receiver, check that the
operating voltage is identical with your local
power supply.
The operating voltage is indicated on the
nameplate on the back of the receiver.
• The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
• If you are not going to use the receiver for a
long time, be sure to disconnect the receiver
from the wall outlet. To disconnect the AC
power cord (mains lead), grasp the plug
itself; never pull the cord.
• (Models of area code U2, CA2 only)
One blade of the plug is wider than the other
for the purpose of safety and will fit into the
wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact
your dealer.
• The AC power cord (mains lead) must be
changed only at a qualified service shop.
A TSP signal is a highly precise measuring
signal that utilizes impulse energy, measuring
a wide band, from low to high, in a short
period.
The amount of energy used to measure signals
is important to ensure measurement accuracy
in a normal indoor environment. Using TSP
signals make it possible to measure signals
effectively.
x x.v.Color (x.v.Colour)
x.v.Color (x.v.Colour) enables the more
faithful reproduction of various colors such as
the brilliant colors of flowers and the turquoise
blue of the southern ocean.
On safety
Should any solid object or liquid fall into the
cabinet, unplug the receiver and have it
checked by qualified personnel before
operating it any further.
On power sources
On heat buildup
Although the receiver heats up during
operation, this is not a malfunction. If you
continuously use this receiver at a large
volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid
burning yourself, do not touch the cabinet.
120GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
masterpage: Right
On S-AIR function
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and
prolong the life of the receiver.
• Do not place the receiver near heat sources,
or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
• Do not place anything on top of the cabinet
that might block the ventilation holes and
cause malfunctions.
• Do not place the receiver near equipment
such as a TV, VCR, or tape deck. (If the
receiver is being used in combination with a
TV, VCR, or tape deck, and is placed too
close to that equipment, noise may result,
and picture quality may suffer. This is
especially likely when using an indoor
antenna (aerial). Therefore, we recommend
using an outdoor antenna (aerial).)
• Use caution when placing the receiver on
surfaces that have been specially treated
(with wax, oil, polish, etc.) as staining or
discoloration of the surface may result.
• As the S-AIR product(s) transmits sound by
radio waves, sound may skip when radio
waves are obstructed. This is a characteristic
of radio waves and is not malfunction.
• As the S-AIR product(s) transmits sound by
radio waves, equipment that generates
electromagnetic energy, such as a
microwave oven, may prevent sound
transmission.
• As the S-AIR function uses the radio waves
that share the same frequency as other
wireless systems, such as wireless LAN or
Bluetooth devices, interference or poor
transmission may result. In this case, take
the following steps:
– Avoid placing the S-AIR product(s) near
other wireless systems.
– Avoid using the S-AIR product(s) and the
other wireless systems spontaneously.
– The transmission may be improved by
changing the transmission channel
(frequency) of the other wireless
system(s). For details, refer to the
operating instructions of the other wireless
system(s).
• The transmission distance differs depending
on the usage environment. Find a location
where transmission between the S-AIR main
unit and sub unit is most effective, and install
the S-AIR main unit and sub unit there.
• Place the S-AIR product(s) on the stable
surface off the floor.
• Poor transmission may occur and the
transmission distance may be too short if the
following conditions exist:
– There is a wall/floor made of reinforced
concrete or stone between the S-AIR
product(s).
– There is an iron divider/door or furniture/
electric product made of fireproof glass,
metal, etc., between the S-AIR product(s).
On operation
Before connecting other components, be sure
to turn off and unplug the receiver.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.
If you have any questions or problems
concerning your receiver, please consult your
nearest Sony dealer.
121GB
STR-DN1010
4-174-068-11(1)
Additional Information
On placement
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem. Should any problem persist, consult
your nearest Sony dealer.
Audio
There is no sound, no matter which
component is selected, or only a very
low-level sound is heard.
• Check that the speakers and components
are connected securely.
• Check that all speaker cords are connected
correctly.
• Check that both the receiver and all
components are turned on.
• Check that MASTER VOLUME control is
not set to “VOL MIN”.
• Check that the SPEAKERS is not set to
“SPK OFF” (page 37).
• Check that headphones are not connected
to the receiver or S-AIR surround
amplifier.
• Press MUTING (RM-AAP051 only) or
(RM-AAP052 only) on the remote to
cancel the muting function. You can also
use MUTING on the receiver.
• Check that you have selected the correct
component with the input buttons
(page 46).
• The protective device on the receiver has
been activated. Turn off the receiver,
eliminate the short-circuit problem, and
turn on the power again.
There is no sound from a specific
component.
• Check that the component is connected
correctly to the audio input jacks for that
component.
• Check that the cord(s) used for the
connection is (are) fully inserted into the
jacks on both the receiver and the
component.
masterpage: Left
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the
PHONES jack to verify that sound is
output from the headphones. If only one
channel is output from the headphones, the
component may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both
channels are output from the headphones,
the front speaker may not be connected to
the receiver correctly. Check the
connection of the front speaker which is
not outputting any sound.
• Make sure you have connected to both the
L and R jacks of an analog component, and
not only to either the L or R jack. Use an
audio cord (not supplied). However, there
will be no sound from the center speaker
when a sound field (2ch Stereo, etc.) is
selected. When the center speaker is not
connected, sound is output only from the
front left/right speakers.
There is no sound from analog 2
channel sources.
• Check that the selected digital audio input
jack is not assigned to other inputs in
“Input Assign” in the Input Option menu
(page 85).
• Check that the INPUT MODE is not set to
“AUTO” (page 84) and the “Input Assign”
function is not used to reassign the audio
input of another source to the selected
input (page 85).
• Check that the INPUT MODE is not set to
“AUTO” (page 84) and the DIGITAL
connection is not made for the selected
input.
122GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
There is no sound from digital sources
(from COAXIAL or OPTICAL input jack).
• Check that the INPUT MODE is set to
“AUTO” (page 84).
• Check that the “Analog Direct” is not
being used.
• Check that the selected digital audio input
jack is not assigned to other inputs in
“Input Assign” in the Input Option menu
(page 85).
• Set “ARC” to “ARC OFF” when no sound
is output from TV OPTICAL IN jack
during TV input (page 100).
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components
are connected correctly and securely.
• Adjust the balance parameters using the
Speaker Settings menu in GUI menu.
There is severe hum or noise.
• Check that the speakers and components
are connected securely.
• Check that the connecting cords are away
from a transformer or motor, and at least
10 feet (3 meters) away from a TV set or
fluorescent light.
• Move your audio components away from
the TV.
• The plugs and jacks are dirty. Wipe them
with a cloth slightly moistened with
alcohol.
masterpage: Right
There is no sound, or only a very lowlevel sound is heard from the center/
surround/surround back/front high
speakers.
• Select a Cinema Studio EX mode (page
65, 66).
• Adjust the speaker level (page 92).
• Make sure the center/surround speaker (s)
is (are) set to either “Small” or “Large”.
• Check that the speaker settings are
appropriate using the Auto Calibration
menu or “SP Pattern” in the Speaker
Settings menu. Then check that sound is
output from each speaker correctly, using
“Test Tone” in the Speaker Settings menu.
There is no sound from the surround
back speakers.
• Some discs have no Dolby Digital
Surround EX flag even though the
packages have Dolby Digital Surround EX
logos.
• Check the “SP Pattern” setting (page 91).
There is no sound from the subwoofer.
• Check that the subwoofer is connected
correctly and securely.
• Make sure you have turned on your
subwoofer.
• Depending on the selected sound field, no
sound output from the subwoofer.
• When all speakers are set to “Large” and
“Neo:6 Cinema” or “Neo:6 Music” is
selected, there is no sound from the
subwoofer.
• Check the “SP Pattern” setting (page 91).
continued
123GB
STR-DN1010
4-174-068-11(1)
Additional Information
The surround effect cannot be
obtained.
• Make sure you have selected the sound
field for movie or music (page 65 or 66).
• Sound fields do not function for signals
with a sampling frequency of more than
48 kHz.
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
Dolby Digital or DTS multi channel
sound is not reproduced.
• Check that the DVD, etc. you are playing
is recorded in Dolby Digital or DTS
format.
• When connecting the DVD player, etc., to
the digital input jacks of this receiver,
make sure the setting for the digital audio
output of the connected component is
available. For example, when connecting
the “PlayStation 3”, set the BD/DVD
audio output format to “Bitstream” on the
“PlayStation 3”.
• Set “Audio Out” to “AMP” in the HDMI
Settings menu.
Recording cannot be carried out.
• Check that the components are connected
correctly.
• Select the source component using the
input buttons (page 46).
The MULTI CHANNEL DECODING lamp
does not light up in blue.
• Check that the playback component is
connected to a digital jack and the input is
selected properly on this receiver.
• Check whether the input source of the
software being played back corresponds to
the multi channel format.
• Check whether the setup on the playback
component is set to multi channel sound.
• Check to make sure the selected digital
audio input jack is not assigned to other
inputs in “Input Assign” in the Input
Option menu (page 85).
masterpage: Left
There is no sound from the component
connected to the DIGITAL MEDIA PORT
adapter.
• Adjust the volume of this receiver.
• The DIGITAL MEDIA PORT adapter
and/or component is not connected
correctly. Turn off the receiver, then
reconnect the DIGITAL MEDIA PORT
adapter and/or component.
• Check the DIGITAL MEDIA PORT
adapter and/or component device to make
sure it supports this receiver.
Video
There is no picture or an unclear
picture appears on the TV screen.
• Select the appropriate input using the input
buttons.
• Set your TV to the appropriate input mode.
• Move your audio components away from
the TV.
• Assign the component video input
correctly.
• The input signal should be same as the
input function when you are up-converting
an input signal with this receiver
(page 34).
• Depending on the DIGITAL MEDIA
PORT adapter, video output may not be
possible.
Recording cannot be carried out.
• Check that the components are connected
correctly.
• Select the source component using the
input buttons (page 46).
124GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
The GUI menu does not appear on the
TV screen.
• Press GUI MODE repeatedly to select
“MENU ON”. If the GUI menu still does
not appear on the TV screen, press MENU.
• Check that the TV is connected correctly.
HDMI
The source sound input from the HDMI
jack on the receiver is not output from
the speakers connected to the receiver
or TV speaker.
• Check the setting of “Audio Out” in the
HDMI Settings menu (page 98).
• Check that the component is connected
correctly to the HDMI jack for that
component.
• You cannot listen to the Super Audio CD
by connecting HDMI.
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with each component.
• Be sure to use a High Speed HDMI cable
when you view images or listen to sound
during Deep Color (Deep Colour) or 3D
transmission.
The Control for HDMI function does not
work.
• Check the HDMI connection (page 27).
• Make sure “Ctrl for HDMI” is set to “ON”
in HDMI Settings menu.
• Make sure the connected component is
compatible with the Control for HDMI
function.
• Check the Control for HDMI settings on
the connected component. Refer to the
operating instructions of the connected
component.
• Repeat the procedures of “Preparing for
the “BRAVIA” Sync” if you change the
HDMI connection, connect/disconnect the
AC power cord (mains lead), or when
there is a power failure (page 70).
No sound is output from the receiver
and TV speaker while using the System
Audio Control function.
• Make sure the TV is compatible with the
System Audio Control function.
• If the TV does not have System Audio
Control function, set the “Audio Out”
settings in HDMI Settings menu to
– “TV+AMP” if you want to listen to the
sound from the TV speaker and
receiver.
– “AMP” if you want to listen to the
sound from the receiver.
• When you connect the receiver to a video
component (projector, etc.), sound may
not be output from the receiver. In this
case, select “AMP”.
• If you cannot listen to the sound of a
component connected to the receiver
while TV input is selected on the receiver
– Change the input of the receiver to
HDMI when you want to watch a
program on a component connected via
HDMI connection to the receiver.
– Change the TV channel when you want
to watch a TV broadcast.
– Select the component or input you want
to watch when you watch a program on
the component connected to the TV.
Refer to the operating instructions of the
TV on this operation.
continued
125GB
STR-DN1010
4-174-068-11(1)
Additional Information
The source image input to the HDMI
jack on the receiver is not output from
the TV.
• Make sure that cables are correctly and
securely connected to components.
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with each component.
• Be sure to use a High Speed HDMI cable
when you view images or listen to sound
during Deep Color (Deep Colour) or 3D
transmission.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
The TV’s remote cannot be used to
control the connected component
when using the Control for HDMI
function.
• Depending on the connected component
and TV, you may need to set up the
component and TV. Refer to the operating
instructions supplied with each component
and TV.
• Change the input of the receiver to the
HDMI input connected to the component.
When the receiver is in standby mode,
there is no image or sound output from
the TV.
• When the receiver is in standby mode,
image and sound are output from the
HDMI component selected the last time
you turned off the receiver. If you are
enjoying other component, play the
component and perform the One-Touch
Play operation, or turn on the receiver to
select the HDMI component you want to
enjoy.
• Make sure “Pass Through” is set to “ON”
in the HDMI Settings menu if you connect
components not compatible with the
“BRAVIA” Sync to the receiver (page 98).
masterpage: Left
S-AIR function
S-AIR connection is not established
(sound transmission is not
established), e.g., the indicator of the
S-AIR sub unit turns off, flashes, or
turns red.
• If you use another S-AIR main unit, place
it more than 26 feet (8 meters) away from
this S-AIR main unit.
• Confirm the S-AIR IDs of the S-AIR main
unit and S-AIR sub unit are the same
(page 77).
• Another S-AIR sub unit is paired to the
S-AIR main unit. Pair the desired S-AIR
sub unit with the S-AIR main unit
(page 78).
• Place the S-AIR main unit and S-AIR sub
unit separately from other wireless
devices.
• Avoid using any other wireless devices.
• The S-AIR sub unit is turned off. Make
sure the AC power cord (mains lead) is
connected and turn on the S-AIR sub unit.
No sound is heard from the S-AIR
receiver.
• Check that the components are connected
to the receiver.
126GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
No sound is heard from the S-AIR
product.
• If you use another S-AIR main unit, place
it more than 26 feet (8 meters) away from
this S-AIR main unit.
• Confirm the ID of the S-AIR main unit and
S-AIR sub unit are the same (page 77).
• Confirm the pairing setting (page 78).
• Place the S-AIR main unit and S-AIR sub
unit closer to each other.
• Avoid using the equipment that generates
electromagnetic energy, such as a
microwave oven.
• Place the S-AIR main unit and S-AIR sub
unit separately from other wireless
devices.
• Avoid using any other wireless devices.
• Change the “RF Change” setting (page
81).
• Change the ID settings of the S-AIR main
unit and S-AIR sub unit.
• Turn off the system and S-AIR sub unit,
then turn them on again.
• Check that headphones are not connected
to the S-AIR sub unit.
“HP NO LINK” and “VOL MIN” appear
alternately on the display and the
volume of the receiver becomes
minimum.
• Volume becomes minimum when you turn
off the surround amplifier with
headphones connected or if the radio
reception is poor. In these cases, check the
radio reception and adjust the volume
level to restore sound from the
headphones.
Tuner
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied)
to connect the receiver to an outdoor FM
antennas (aerial) as shown below. If you
connect the receiver to an outdoor antenna
(aerial), ground it against lightning. To
prevent a gas explosion, do not connect the
ground (earth) wire to a gas pipe.
Outdoor FM antenna (aerial)
Receiver
Ground wire
(not supplied)
To ground
Additional Information
There is noise or the sound skips.
• If you use another S-AIR main unit, place
it more than 26 feet (8 meters) away from
this S-AIR main unit.
• Sources with copyright protection may not
be playable on S-AIR sub unit.
• Place the S-AIR main unit and S-AIR sub
unit closer to each other.
• Avoid using the equipment that generates
electromagnetic energy, such as a
microwave oven.
• Place the S-AIR main unit and S-AIR sub
unit separately from other wireless
devices.
• Avoid using any other wireless devices.
• Change the “RF Change” setting (page
81).
• Change the ID settings of the S-AIR main
unit and S-AIR sub unit.
masterpage: Right
continued
127GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
Radio stations cannot be tuned in.
• Check that the antennas (aerials) are
connected securely. Adjust the antennas
(aerials) and connect an external antenna
(aerial), if necessary.
• (Models of area code U2, CA2 only)
Keep the satellite radio antenna, away
from the speaker cords and the power cord
to avoid picking up noise.
• The signal strength of the stations is too
weak (when tuning in with automatic
tuning). Use direct tuning.
• Make sure you set the tuning interval
correctly (when tuning in AM stations
with direct tuning).
• No stations have been preset or the preset
stations have been cleared (when tuning
by scanning preset stations). Preset the
stations (page 55).
• Press AMP, then press DISPLAY
repeatedly on the remote so that the
frequency appears on the display.
The receiver cannot receive satellite
channels at all.a)
• The receiving condition is not good. Move
the antenna to the place where the
condition is good.
• Check that you subscribed to the satellite
radio service you want (page 57).
RDS does not work.b)
• Make sure that you are tuned to an FM
RDS station.
• Select a stronger FM station.
The RDS information that you want
does not appear.b)
• Contact the radio station and find out
whether they actually provide the service
in question. If so, the service may be
temporarily out of order.
a)
b)
masterpage: Left
Remote commander
The remote does not function.
• Point the remote at the remote sensor on
the receiver.
• Remove any obstacles in the path between
the remote and the receiver.
• Replace all the batteries in the remote with
new ones, if they are weak.
• Make sure you select the correct input on
the remote.
• When you operate a programmed nonSony component, the remote may not
function properly depending on the model
and the maker of the component.
Others
The receiver is turned off
automatically.
• The “Auto Standby” function is working
(page 100).
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. See the following table
to solve the problem. If any problem persists,
consult your nearest Sony dealer.
PROTECTOR
Irregular current is output to the speakers, or
upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
Models of area code U2, CA2 only.
Models of area code CEK, ECE, AU1, TW2 only.
128GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
For other messages, see “Message list after
Auto Calibration measurement” (page 43),
“DIGITAL MEDIA PORT message list”
(page 51) and “SIRIUS Satellite Radio
message list” (page 64).
If you are unable to remedy the
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy
the problem (page 37). However, note that all
memorized settings will be reset to their initial
settings and you will have to readjust all
settings on the receiver.
If the problem persist
Consult your nearest Sony dealer. Note that if
service personnel changes some parts during
repair, these parts may be retained.
In the event of a problem with S-AIR function,
have a Sony dealer check the entire system
together (S-AIR main unit and S-AIR sub
unit).
Reference sections for clearing
the receiver’s memory
To clear
See
All memorized settings
page 37
Customized sound fields
page 69
masterpage: Right
Specifications
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(Models of area code U2 only)
With 8 ohm loads, both channels driven, from
20 Hz – 20,000 Hz; rated 100 watts per
channel minimum RMS power, with no more
than 0.09% total harmonic distortion from
250 milliwatts to rated output.
Amplifier section
Models of area code U21)
Minimum RMS Output Power
(8 ohms, 20 Hz – 20 kHz, THD 0.09%)
100 W + 100 W
Stereo Mode Output Power
(8 ohms, 1 kHz, THD 1%)
110 W + 110 W
Surround Mode Output Power2)
(8 ohms, 1 kHz, THD 10%)
150 W per channel
Models of area code CA21)
Minimum RMS Output Power
(8 ohms, 20 Hz – 20 kHz, THD 0.09%)
95 W + 95 W
Stereo Mode Output Power
(8 ohms, 1 kHz, THD 1%)
110 W + 110 W
Surround Mode Output Power2)
(8 ohms, 1 kHz, THD 10%)
150 W per channel
continued
129GB
STR-DN1010
4-174-068-11(1)
Additional Information
Models of area code CEK, ECE, AU1, TW21)
Stereo Mode Output Power
(8 ohms, 1 kHz, THD 1%)
100 W + 100 W
Surround Mode Output Power2)
(8 ohms, 1 kHz, THD 10%)
140 W per channel
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
1)
Measured under the following conditions:
AM tuner section
Area code
Power requirements
Tuning range
U2, CA2
120 V AC, 60 Hz
Area code
CEK, ECE, AU1
230 V AC, 50 Hz
TW2
110 V AC, 60 Hz
2)
Reference power output for front, center,
surround, surround back and front high speakers.
Depending on the sound field settings and the
source, there may be no sound output.
Frequency response
Analog
10 Hz – 70 kHz,
+0.5 dB/–2 dB (with sound
field and equalizer
bypassed)
Input
Analog
Sensitivity: 500 mV/
50 kohms
S/N3): 96 dB
(A, 500 mV4))
Digital (Coaxial) Impedance: 75 ohms
S/N: 100 dB
(A, 20 kHz LPF)
Digital (Optical) S/N: 100 dB
(A, 20 kHz LPF)
Output (Analog)
AUDIO OUT
Voltage: 500 mV/10 kohms
SUBWOOFER
Voltage: 2 V/1 kohm
Equalizer
Gain levels
±10 dB, 1 dB step
masterpage: Left
Tuning scale
10 kHz step
9 kHz step
U2, CA2
530 kHz –
1,710 kHz
531 kHz –
1,710 kHz
CEK, ECE, AU1,
TW2
–
531 kHz –
1,602 kHz
Antenna (aerial)
Loop antenna (aerial)
Intermediate frequency
450 kHz
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
HDMI Video
SHORT (with sound field and equalizer
bypassed).
4)
Weighted network, input level.
Input/Output (HDMI Repeater block)
640 × 480p@60 Hz
720 × 480p@59.94/60 Hz
1280 × 720p@59.94/60 Hz
1920 × 1080i@59.94/60 Hz
1920 × 1080p@59.94/60 Hz
720 × 576p@50 Hz
1280 × 720p@50 Hz
1920 × 1080i@50 Hz
1920 × 1080p@50 Hz
1920 × 1080p@24 Hz
FM tuner section
HDMI Video (3D)
Tuning range
87.5 MHz – 108.0 MHz
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
Intermediate frequency
10.7 MHz
Input/Output (HDMI Repeater block)
1280 × 720p@59.94/60 Hz Frame packing
1920 × 1080i@59.94/60 Hz Frame packing
1920 × 1080i@59.94/60 Hz Side-by-Side (Half)
1920 × 1080p@59.94/60 Hz Side-by-Side (Half)
1280 × 720p@50 Hz Frame packing
1920 × 1080i@50 Hz Frame packing
1920 × 1080i@50 Hz Side-by-Side (Half)
1920 × 1080p@50 Hz Side-by-Side (Half)
1920 × 1080p@24 Hz Frame packing
3) INPUT
130GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB07ADD_STR-DN1010-CEL.fm
masterpage: Right
General
Power requirements
Area code
Power requirements
U2, CA2
120 V AC, 60 Hz
ECE, CEK
230 V AC, 50/60 Hz
AU1
230 V AC, 50 Hz
TW2
110 V AC, 60 Hz
Power output (DIGITAL MEDIA PORT)
DC OUT:
5V, 0.7A MAX
Power consumption
Area code
Power consumption
U2, CA2, CEK,
ECE, AU1, TW2
250 W
Power consumption (during standby mode)
0.9 W (When “Ctrl for
HDMI” and “S-AIR Stby”
are set to “OFF”)
Dimensions (width/height/depth) (Approx.)
17 in × 6 1/4 in × 12 7/8 in
(430 mm × 157.5 mm ×
324.5 mm) including
projecting parts and
controls
Mass (Approx.)
18 lb 16 oz (8.6 kg)
For details on the area code of the
component you are using, see page 4.
Design and specifications are subject to
change without notice.
Halogenated flame retardants are not used in
the certain printed wiring boards.
Additional Information
131GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CELIX.fm
masterpage: Left
Index
Numerics
D
L
2 channel 65
5.1 channel 19
7.1 channel 19
DCAC (Digital Cinema Auto
Calibration) 38
Decode Priority 97, 105
DIGITAL MEDIA PORT 48
DIMMER 111
Direct Tuning 54, 60, 109,
110
Display 11
Distance Unit 95, 103
Dolby Digital EX 68
Dual Mono 96, 105
DVD player 28, 31
DVD recorder 33
Dynamic range compression
94, 102
Level settings 102
LFE (Low Frequency Effect)
12
Lock Code 62
A
A.F.D. mode 65
A/V Sync 96, 105
AM 53, 109
Analog Direct 65
Antenna Aiming 59, 104,
110
Audio Return Channel 74
Audio settings 96, 105
Auto Calibration settings 90,
102
Auto Tuning 54
B
BI-AMP 91
Bi-amplifier connection 88
Blu-ray disc player 28, 30
BRAVIA Sync
preparing 70
C
Cable TV tuner 32
Calibration Type 90, 102
Camcoder 33
Category Mode 59, 110
CD player 24
Changing the display 47
Clear
memory 37
remote 116
sound field 69
Connection
antennas 35
audio components 24
speakers 21
TV 23
video components 26
Control for HDMI 98
Crossover frequency 93, 103
E
M
Menu 89, 102
Message
Auto Calibration 43
DIGITAL MEDIA
PORT 51
Error 128
SIRIUS 64
Movie mode 65
Music mode 66
Muting 47
Effect level 95
EQ settings 96, 104
Error messages 128
N
F
O
FM 53, 109
FM Mode 54, 104
One-Touch Play 72
Option menu 45
G
P
GUI (Graphical User
Interface) 44
PAIRING 78
Parental Lock 62, 104
Party Mode 80
Phase Audio 94, 102
Phase Noise 94, 102
“PlayStation 3” 28
Position 90, 102
Preset channels 61, 110
Preset Mode 60
Preset stations 55, 109
PROTECTOR 128
H
HDMI Pass Through 98, 105
HDMI settings 98, 105
I
Input Assign 86
INPUT MODE 84
iPod 49
Name Input 47, 56
NIGHT MODE 69
132GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CELIX.fm
masterpage: Right
R
Radio ID 58
RDS 56
Recording 52
Remote 14, 112
Reset 37
Resolution 97, 105
S
S-AIR 75
S-AIR settings 106
Satellite tuner 28, 32
Settings menu 89
SIRIUS Satellite Radio 57,
110
Sleep Timer 52
Sound Field 65, 95
Speaker settings 91, 103
Subwoofer Level 99, 105
Super Audio CD player 24
Surround settings 95, 104
System Audio Control 72
System Power Off 73
System settings 105
T
Test Tone 93, 102
Theater/Theatre Mode Sync
73
Tuner 53
Tuner settings 104
Tuning 54, 55
TV 23, 28
U
Up converting 34
Additional Information
V
VCR 33
Video settings 97, 105
133GB
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CELIX.fm
masterpage: Left
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CELIX.fm
masterpage: Left
STR-DN1010
4-174-068-11(1)
D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB01COV_STR-DN1010-CELIX.fm
masterpage: Left
Sony Corporation Printed in Malaysia
model name1[STR-DN1010]
[4-174-068-11(1)]