advertisement
BTS Touch Exit Button
Installation Instruction
Specifications
Mode BTS-100
Operating Voltage
Current Draw
12~24VDC
30~60mA/12VDC
40~80mA/24VDC
Relay contact output
Com,N/C,N/O
Relay rating 3A/30VDC
BTS-115-ANSI,115-S
12~24VDC
30~50mA/12VDC
40~60mA/24VDC
Com,N/C,N/O
3A/24VDC
BTS-85UK
12~24VDC 12~24VDC
20~40mA/12VDC
20~50mA/24VDC
60~100mA/12VDC
80~120mA/24VDC
12~24VDC
30~60mA/12VDC
40~80mA/24VDC
Com,N/C,N/O Com,N/C,N/O Com,N/C,N/O
3A/24VDC
BTS-400ANSI,300
3A/24VDC
BTS-486
3A/24VDC
Relay strike time
LED status indication
Temperature
Other
1~30 seconds
Green(Relay)
-20~+70ºC
1~30 seconds
Green(Relay)
-20~+70ºC
1~30 seconds
Green(Relay)
-20~+70ºC
1~30 seconds 1~30 seconds
2x6 levels of LED indicator
-20~+70ºC
2x6 levels of LED indicator
-20~+70ºC
N/O,N/C output setting
Wiring Diagram
The BTS touch sensitive exit button has
N.O. and N.C. contact output and can be connected directly to a electromagnetic lock or a proximity reader in series (or in parallel).
Control Device (Outdoor)
Relay output control
Fig.A
In Fig.A, BTS controls the fail-safe locking device directly by series connection. BTS relay time is door-opening time.
Power
Supply
1 30 sec.
Relay Timer
Locking Device
(fail-safe)
BTS Touch Sensitive Switch (Indoor)
Fig.B
In Fig.B, BTS controls the fail-secure locking device directly by parallel connection. BTS relay time is door-opening time.
Control Device (Outdoor)
Relay output control
Locking Device
(fail-secure)
1 30 sec.
Relay Timer
Power
Supply
BTS Touch Sensitive Switch (Indoor)
Note:
1. Make sure that the power input and relay rating output (3Amp/24VDC) are correct.
2. Make sure that the “+” and “-” wires are connected correctly.
3. The door strike or relay must have a varistor or a diode across the door strike terminals to suppress the
back EMF of the strike. Failure to do so will damage the relay contacts and electronic omponents, or
even burn the controller.
Copyright © GIANNI Industries,Inc.All rights reserved.
P-MU-BTS Ver.D Published 2011.03.18
Illustration
BTS Touch Exit Button
Base
Slot hole
LED
Vandal resistant screw
Stopper
Touch panel
The relay will send the signals from N.C. into N.O. contact after your finger or a metal object touches the touch panel.
Time delay can be adjusted from 1 to 30 seconds.
JP setting
Relay output
(Touch)
Relay output
(Touch)
(Light stay on)
Relay output
Relay output
(Light flash)
(Green)
(Touch)
(Red)
(Touch)
(Green)
(Touch)
(Off)
(Touch)
(Red)
(Touch)
(Off)
(Touch)
(Red)
(Green)
(Off)
(Green)
(Off)
(Red)
BTS-400-ANSI,300,486
Relay contact output
(dry contact)
12~24 VDC power input
JP setting
Relay Timer
(Sec.)
Warranty
The product is warranted against defects in material and workmanship while used in normal service for a period of 1 year from the date of sale to the original customer. The GEM policy is one of continual development and improvement; therefore GEM reserves the right to change specifications without notice.
Copyright © GIANNI Industries,Inc.All rights reserved.
P-MU-BTS Ver.D Published 2011.03.18
advertisement
Related manuals
advertisement