Earn BISSELL Rewards!
Register your
product today!
See details on
back page
®
USER'S GUIDE
52C2, 61C5 SERIES
2
Thank You
3
Safety Instructions
4
Product View
5-7
Assembly
7-9
Operations
10-15
Maintenance and Care
16
Troubleshooting
17
Replacement Parts
18
Accessories
19
Warranty
20
Product Registration
20
Consumer Care
product
images
may vary
Thanks for buying a BISSELL Total Floors® Vacuum
We’re glad you purchased a BISSELL Total Floors® vacuum. Everything
we know about floor care went into the design and construction of this
complete, high-tech home cleaning system.
Your BISSELL Total Floors® vacuum is well made, and we back it with a
limited warranty. We also stand behind it with a knowledgeable, dedicated
Consumer Care department, so, should you ever have a problem, you’ll
receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL
is a global leader in the design, manufacture, and service of high quality
homecare products like your Total Floors® vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman & CEO
2
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
Read all instructions before using
your upright VACUUM.
WARNING:
To reduce the risk of fire,
electric shock, or injury:
■Always connect to a polarized outlet (left slot is
wider than right). Unplug from outlet when not
in use and before conducting maintenance.
■Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■Do not leave vacuum cleaner unattended
when it is plugged in.
■Unplug from outlet when not in use and
before servicing.
■Unplug before attaching the TurboBrush Tool.
■Do not use outdoors or on wet surfaces.
■Do not allow children to operate vacuum
cleaner or use as a toy.
■Close attention is necessary when used by
or near children.
■Do not use for any purpose other than
described in this user’s guide.
■Use only manufacturer’s recommended
attachments.
■Do not use with damaged cord or plug.
■If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, have it repaired at an
authorized service center.
■Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
appliance over cord. Keep cord away from
heated surfaces.
■Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
■Do not handle vacuum cleaner or plug with
wet hands.
■Do not put any object into openings. Do not
use with any opening blocked; keep openings
free of dust, lint, hair, and anything that may
reduce air flow.
■Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
■Turn off all controls before plugging or
unplugging vacuum cleaner.
■Use extra care when cleaning stairs.
■Do not pick up flammable materials (lighter
fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapors.
■Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.).
■Do not use vacuum cleaner in an enclosed
space filled with vapors given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other explosive
or toxic vapors.
■Do not pick up hard or sharp objects such as
glass, nails, screws, coins, etc.
■Do not pick up anything that is burning
or smoking, such as cigarettes, matches,
or hot ashes.
■Do not use without filters in place.
■Use only on dry, indoor surfaces.
■Keep appliance on a level surface.
■Do not carry the vacuum cleaner while
it is running.
SAVE THESE
INSTRUCTIONS.
This model is for household use only.
Commercial use of this unit voids the
manufacturer’s warranty.
THIS APPLIANCE
HAS A POLARIZED
PLUG.
To reduce the risk of electric shock, this
appliance has a polarized plug (one blade
is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician to install a proper outlet. Do not
change the plug in any way.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
3
Product view
Upper
Handle
Cord Clip
Select models include
Pet TurboEraser®
Tool or TurboBrush®
Tool
Power
Cord
Combination
Dusting
Brush/
Upholstery
Tool
Suction Power
Indicator
Carry
Handle
Quick
Release®
Cord Wrap
Power Switch
Easy Empty™
Dirt Container
Stretch Hose
Extension
Handle
Crevice
Tool
Post-Motor
Filter*
Specialty
Tool**
Lock ’n
Seal™ Lever
Pre-Motor
Filter
Hose
Wand Base
Height
Adjustment
Knob
Edge
Cleaning
Port
Pet Hair Lifter (select models)
WARNING:
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
4
Brush On/
Off Pedal
Recline
Pedal
Foot
Hose
*Select models include a Febreze® post-motor filter.
For ordering information, turn to page 17.
**Select models may include Pet Hair Fabric Tool or
Long Reach Dusting Tool
Febreze® and related trademarks are owned by
The Procter & Gamble Company, Cincinnati, Ohio
and used under license by BISSELL, Inc.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Assembly
Warning:
The only tool you’ll need to assemble your
vacuum cleaner is a Phillips screwdriver.
Plastic film can be dangerous.
To avoid danger or suffocation,
keep away from babies
and children.
Locate and install filters
Important: Before using your vacuum, make
sure that all filters (pre-motor and post-motor) are
in place. Do not operate your vacuum without
these filters. Your Total Floors vacuum comes preloaded with a post-motor foam filter. If you wish
to use the post-motor Febreze® filter instead,
locate the Febreze® filter in the vacuum carton
and remove the filter from its packaging. Next,
remove the post-motor foam filter from the filter
door and insert the Febreze® filter in its place as
is shown to the right (A). Do not use your vacuum
without one of these filters in place. Do not use
both filters together.
Attach handle to vacuum
1. Locate the carry handle. Remove the screw
packet taped to the carry handle. There are
three screws in this screw packet. Two screws
are used to attach the upper handle and carrying handle to the vacuum base. One screw
is used to attach the hose guide/tool caddy.
A.
1.
2.
3.
2. Stand the vacuum upright. From the back
of the vacuum body, slide the base of the
upper handle firmly into the grooves at the
top of the vacuum body. Continue to push
so that there are no gaps and the front of
the handle is flush with the vacuum body.
3. With the upper handle firmly placed on the
vacuum body, guide the carrying handle
into place onto the back of the upper handle
and insert two of the screws into the existing
holes. (Reference the rear-facing product
view on page 4 to see how the carry handle
should look). Tighten screws securely with
a Phillips screwdriver to anchor the carry
handle to the upper handle and the upper
handle to the vacuum body.
a.
Attach the vacuum hose & tools
1.Attach the 3 hose/tool storage pieces to the
back of the unit.
a. Attach the tool storage clip to the back of
the handle by snapping the piece into the
unit as shown. Push piece straight in until
it snaps into place.
b. Attach the hose guide clip to the left side
of the back of the vacuum. Insert tab at a
45 degree angle and turn clockwise so it
snaps into place.
b.
c.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
5
Assembly
Attach the vacuum hose & tools continued
c. The hose guide/tool caddy should be
attached at the bottom of the back of
the vacuum. Slide into place and insert
screw into the existing hole. Tighten
securely with a Phillips screwdriver.
2. Line up the tabs of the Twist n’ Snap hose with the
corresponding notches and turn clockwise. Slide
the end of the hose into the hose wand base.
Hose wraps on back of unit as shown on page 4.
3.Place the TurboBrush Tool or Pet TurboEraser
Tool into its holder from the front of the vacuum.
Power cord
To store the power cord, wrap cord around the
upper and lower cord wrap on the side of the
vacuum. To release the power cord, rotate the
upper cord wrap down and gently pull off cord.
Power switch
The power switch is located just below the
carrying handle on the side of the vacuum.
Push the rocker switch “ON” (I) to vacuum,
and “OFF” (O) when cleaning is complete.
Brush Roll Power
The rotating brush ON/OFF pedal is located on
the foot of the vacuum. You can use your foot to
engage or disengage this pedal (A). When the
brush roll pedal has been engaged, the brush
will start rotating. The brush roll should be turned
on for most carpeted floors. To turn the brush roll
off, disengage the pedal by pressing on it with
your foot. We recommend turning off the brush
roll for bare floor cleaning to prevent scatter or
for other delicate surfaces.
NOTICE:
The brush roll continues to rotate while
using your vacuum for above floor
cleaning. To prevent carpet damage,
turn the brush roll off and do not lean
on vacuum or tilt forward.
CAUTION:
Before using your vacuum,
make sure that the dirt container is in the locked position
and that all filters (pre-motor
and post-motor) are in place.
Do not operate your vacuum
without these filters.
Tip:
Your vacuum features a quickrelease cord wrap. To remove the
power cord quickly and easily,
rotate the upper cord wrap towards
the floor, and slip the cord off.
A
Edge Suction
To make edge cleaning more convenient,
remove the hose from the hose wand base
and attach the crevice tool. Insert the crevice
tool into the port on the foot of the vacuum (B).
Suction is now diverted to the front corner of
the vacuum and you can clean along edges
and into corners. It is recommended you turn
off the brush roll when using this feature.
(B)
Tip:
Do not use extension wand when
using the Edge Suction Feature.
6
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Assembly
Handle Positions
Using your foot, press the handle
release pedal, located on the lower
left side of the vacuum to recline to
a cleaning position.
1.
2.
1.Upright – For storage and above floor
cleaning with tools.
2. Normal Cleaning – Press handle release
pedal once. This position is used for most
household floor cleaning tasks.
Operations
Transporting your cleaner
1. To move your vacuum cleaner from room
to room, put the handle in the upright
position, tilt the cleaner back on its rear
wheels and push forward.
2. The vacuum cleaner can also be moved by
using the carry handle on the back.
Height Adjustments
There are seven height settings available for
various floor surfaces. Turn the dial on the foot
of the cleaner to the desired setting.
Lowest setting – for low pile carpeting
or bare floors. To pick up debris it may be
necessary to move up one setting.
Medium settings – for medium pile carpet.
High setting – for high pile and most
shag/frieze carpet.
ATTENTION:
Some frieze carpets have long, delicate
fibers or threads that may be damaged
by the rotating brush during vacuuming.
It is recommended the rotating brush be
turned OFF when cleaning this type of
carpet.
Tip:
Before cleaning under low furniture,
check area first for objects that
might harm the unit or block the
vacuum hose
Note: For optimal carpet cleaning
performance, adjust to the lowest
practical setting. If your cleaner is
difficult to push, adjust to the next
higher setting.
If the dial is difficult to turn, tilt the cleaner
back slightly to take the weight off of the
foot while turning.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
7
Operations
Clean filter indicator
The clean filter indicator tells you when the air
flow in your vacuum is reduced due to dirty
filters or a clog in the hose. The clean filter
indicator will remain green until the airflow is
reduced. At that time, it begins to change to
red. When the indicator is fully red, the airflow
is significantly reduced or clogged by a dirty filter. Follow the steps on page 11 to clean your
filters or there is a clog in the hose. All filters
in the vacuum should be cleaned or replaced
when the clean filter indicator turns red. To
check and remove the clog, follow the steps on
page 12 to check for and clear clogs.
NOTE: When your vacuum is
turned off, the clean filter indicator
will go to the red color setting.
The clean filter indicator only
detects reductions in airflow
when the vacuum power is on.
On-board Tools
Your vacuum is not only a powerful carpet
and rug cleaner; it is also a versatile above
floor vacuum cleaner when you select one
of the special tools.
1. Raise the handle to the upright position.
2. Remove the hose wand from the hose
wand base. This automatically diverts
the suction to the hose.
3. Use the hose alone or attach any tool
by firmly pushing onto the vacuum hose,
hose wand, or extension wand. They
are a friction fit, so be sure the hose
and tool fit snuggly together
Dusting brush / upholstery tool:
Two types of cleaning tools are included in
one attachment. Slide the tool out to use with
or without bristles and switch between the
two uses.
clean filter
indicator
NOTICE:
While vacuuming, certain types of
carpets and low humidity conditions
may generate small static discharges.
The discharges are entirely harmless
and are not associated in any way
with the main power supply
Tip:
It is recommended to turn off
the brush roll when the hose is
removed and you are using the
on-board tools
CAUTION:
Always place the vacuum cleaner on
the floor in its fully upright position
and make sure it is locked in place
when using tools. It is recommended
to turn off the brush roll when
using tools.
a.Use the dusting brush to dust furniture,
blinds, books, lamps, shelves and
baseboards.
b.Slide the brush off to use the upholstery
tool on cushions, draperies and fabrics.
8
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Operations
Pet Hair Fabric Tool
(select models):
Use this tool on fabrics such as drapes, beds
or anywhere else pet hair may collect.
Long Reach Dusting Tool
(select models):
Use this tool for dusting large surfaces.
TurboBrush Tool
(select models):
Use rotating brush action for small flat areas
such as stair and cushions. Press gently down
and pull toward you in raking motion; too much
pressure will cause brush to stop rotating.
Pet TurboEraser Tool
(select models):
Use for removing dirt and pet hair from stairs,
upholstery, area rugs, and other small areas.
Pull the tool towards you in a raking motion.
Note: The Pet TurboEraser Tool is
designed to remove pet hair from
upholstered or carpeted surfaces.
It should not be used on pets.
Emptying the dirt container
Empty the dirt container as soon as the dirt
reaches the “fill” line on the front of the cup.
1.Unplug the vacuum from the electrical outlet.
2.Slide the Lock ‘n Seal lever to the left.
2.
3.Grasp the handle and pull the dirt cup
straight out to remove from the vacuum.
4.Empty dirt into garbage container.
NOTE: Emptying the dirt container
after every use will help prevent
overfilling, and ensure that the
vacuum is ready to go the next
time you clean.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
9
Maintenance and Care
To maximize your cleaning performance
and extend the life of your vacuum, it is
very important that you empty your dirt
container and check and clean your filters
frequently. Follow the instructions on the
following pages, and perform these simple
maintenance steps:
1. Empty the dirt container when the dirt
reaches the “Full” line on the container,
or more frequently, to prevent overfills.
2. Check the pre-motor and post-motor
filter regularly. Clean or replace
as needed.
NOTE: Use of moist parts/components in your unit will damage the
motor and void your warranty
WARNING:
To reduce the risk of electric
shock, turn power switch OFF
and disconnect polarized
plug from electrical outlet before
performing maintenance or
troubleshooting checks.
Tip:
For maximum cleaning performance, check and clean or replace
all filters as suggested
3. Use the hose alone or attach any tool
by firmly pushing onto the vacuum hose,
hose wand, or extension wand. They
are a friction fit, so be sure the hose
and tool fit snuggly together.
NOTE: Be sure to clean or replace
your filters anytime the clean filter
indicator begins to turn red.
NOTE: More frequent filter cleaning
may be necessary if you are
vacuuming new carpet, fine dust,
or have allergy concerns.
Cleaning the dirt container
1. Ensure that the dirt cup has been emptied.
2 While the dirt cup is still out of the
unit,grasp the inner cyclone screen and
twist to the right until the locking tab
stops the rotation. Pull down the inner
cyclone screen to remove it.
inner
cyclone
3 Clean the inner cyclone with a cloth or
soft brush to remove dust or debris.
4. Wipe out the inside of the upper tank
and the inner cyclone with a damp
cloth moistened with water or a mild
cleaning detergent.
10
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Maintenance and Care
Cleaning the dirt container continued
5.If desired, the lower dirt cup may be
washed in warm water. Make sure it is
completely dry before reassembling.
NOTE: Do not put in the dishwasher.
NOTE: Use of moist parts/components in your unit will damage the
motor and void your warranty
NOTICE:
Select models feature a Febreze®
post-motor filter. For purchasing
information, turn to page 17.
6.To reassemble, replace the inner
cyclone screen by sliding it into the
upper tank and rotating it to the left until
the locking tabs stop the rotation.
Cleaning the pre-motor filter
& replacing the post-motor filter
1. Unplug the vacuum from electrical outlet.
2.
2. The pre-motor filter protects the motor
from dirt particles. It is located in
the slide out tray underneath the
dirt container. If the filter becomes
dirty, pull out the tray, lift out the
foam filter pad and clean it.
foam
filter
NOTE: The pre-motor filter may be
hand washed in water with mild
detergent. Rinse well and air dry
thoroughly before replacing.
NOTE: Use of moist parts/components in your unit will damage the
motor and void your warr anty
3.The post-motor filter assists in the filtration process to return clean air to the
room. It is located behind the door
on the side of the vacuum. If the filter
becomes dirty, open the door, remove
the filter and replace.
Warning:
Do not operate vacuum with
damp or wet filters, or without
all filters in place.
3.
4.The Febreze® filter (select models only)
is designed to eliminate odors during
the regular life of the filter. Depending
on usage, the post-motor filter should be
changed every 3-6 months.
NOTE: The post-motor filter is a
white, pleated filter. This filter
is not washable and must be
replaced when it becomes dirty.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
11
Maintenance and Care
Clearing Clogs
1.Turn the power switch off and unplug
the vacuum from the electrical outlet.
2.Check the upper tank for build up or clogs.
3.If you notice dirt build up in the inner
cyclone, follow instruction on how to
clean the inner cyclone in page 10.
4.Check for a clog in the foot hose &
edge cleaning port, the wand or in
the hose.
NOTE: When the indicator reads
Red, there is a clog in the hose
which is diminishing suction
power. Remove the clog in the
hose to restore full suction power.
5. Remove the Twist ‘n Snap hose from
the vacuum by turning to the right.
Straighten the hose and unclog with
a long, narrow object.
6.If you notice debris or dirt clogged in the
foot hose, remove it by pulling it out.
7.If the clog persists, follow the instructions
for checking the rotating floor brush and
drive belt on page 14 and inspect the air
passageway for obstructions.
foot
hose
12
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Maintenance and Care
Maintaining the Pet TurboEraser
Tool and TurboBrush Tool
The Pet TurboEraser Tool should be checked
regularly for clogs and debris wrapping
around the paddles. Select models include
a TurboBrush Tool that follows the same
maintenance instructions.
3.
1. Unplug unit from outlet.
2. Remove tool from hose or vacuum.
3. If clog is present or debris is visible,
unscrew the two screws on the back of
the Pet TurboEraser Tool to remove the
faceplate and clear any obstructions.
4. To clean debris remove the paddles from
the drive belt and clean debris.
5. Reposition the drive belt on the paddle
roll. Place ends of roll in the slots on sides
as shown. Reposition faceplate and secure
with two screws.
NOTE: The Pet TurboEraser Tool is
designed to remove pet hair from
upholstered or carpeted surfaces.
It should not be used on pets.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
13
Maintenance and Care
Check rotating floor brush and drive belt
You should check your vacuum cleaner's
rotating floor brush and drive belt regularly
for wear or damage. You should also clean
the brush and the brush ends of strings,
hair and carpet fibers. This type of debris
can wrap around the brush and hamper its
ability to effectively clean your carpet. Also
remove any debris that has accumulated
under the brush cover.
CAUTION:
To reduce the risk of injury from
moving parts, turn off vacuum
and disconnect power plug from
electrical outlet.
1. Turn the power switch off and unplug
the vacuum from the electrical outlet.
2. Place handle in low position and turn
the vacuum cleaner over so the bottom
side is facing up.
3.Unscrew and lift off the brush cover.
3.
4. Remove the rotating floor brush.
5. Clean strings, hair and other debris
from the rotating floor brush, paying
particular attention to brush ends.
6. Clean strings, hair and other debris
from the motor pulley, drive belt areas,
and the brush ON/OFF power switch
mechanism.
7. Check the drive belt carefully for wear,
cuts, or stressed areas.
4.
8. Check air passageway for obstructions.
Remove debris from this area.
9. Replace belt and brush. Rotate brush
toward motor pulley to seat the belt
properly.
10.Place the brush cover back and secure
with its screws.
14
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Maintenance and Care
Replace drive belt
1.Turn the power switch off and unplug
the vacuum from the electrical outlet.
Remove floor brush following steps 2-4
on page 14.
rotating
floor brush
2.
2. With the rotating floor brush removed
from the vacuum cleaner, grasp the old
drive belt and remove from the motor
pulley. Discard the old drive belt.
motor
pulley
3. Place the new drive belt over the motor
pulley, pass the belt through the opening of the belt ON/OFF mechanism
and loop the belt over the rotating floor
brush in the space between the bristles.
NOTE: It is important that you use
only genuine BISSELL replacement
belts. Generic belts many not meet
the exact specifications required
to keep your vacuum operating at
its peak performance. The use of
unbranded belts could lead to early
failure of the vacuum and could
void your warranty.
4. Place ends of the rotating floor brush
down into the slots on the sides.
Alignment of brush ends is necessary
to ensure the brush is fully inserted.
5. Turn the rotating floor brush by hand
several times. If properly installed,
the drive belt will center itself on the
rotating floor brush crown.
6.
6. Place the brush cover back and secure
with its screws.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
15
Troubleshooting - Total Floors®
Vacuum cleaner won’t turn on
Possible causes
Remedies
1. Power cord not plugged in
1. Check electrical plug
2. Blown fuse/tripped breaker
2. Check/replace fuse or reset breaker
Vacuum cleaner won’t pick up dirt
Possible causes 1. Incorrect height adjustment
Remedies
1. Adjust powerfoot to correct height setting
2. Hose not attached to suction opening 2. Grasp quick reach handle and firmly push
hose wand onto the suction opening
3. Crack or hole in hose
3. Check hose and replace if needed
4. Broken or worn drive belt
4. Replace drive belt, see page 15
5. Rotating floor brush bristles worn
5. Replace brush
6. Rotating floor brush jammed
6. Remove brush and clean debris from brush ends
7. Clog in vacuum- hose/ foot/ body
7. Follow instructions on page 12 for clearing clogs
8. Dirt container full
8. Empty dirt container
9. Dirt container or upper tank not installed properly
9. Position correctly and lock in place
10. Filters are dirty
10. Check and clean pre-motor and
post-motor filters
Tools won't pick up dirt
Possible causes
Remedies
1. Crack or hole in hose
1. Check hose and replace if needed
2. Clog in vacuum
2. Follow instructions on page 12 for clearing clogs
3. Dirt container full
3. Empty dirt container
4. Dirt container or upper tank not installed properly
4. Position correctly and lock in place
5. Filters are dirty
5. Check and clean pre-motor and
post-motor filters
Vacuum cleaner is difficult to push
Possible causes
1. Incorrect height adjustment
Remedies
1. Adjust powerfoot to correct height setting
Visible dirt escaping from cleaner
Possible causes
1. Dirt container full
Remedies
1. Empty dirt container
2. Filters missing or installed incorrectly
2. Check pre-motor and post-motor
filters for correct installation
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of
service. Contact us directly at 1-800-237-7691.
16
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Replacement parts - Total Floors®
Below please find a list of common replacement parts. While not all of these
parts may have come with your specific machine, all are available to you for
purchase, if desired.
Item
1
2
3
4
5
6
7
8
*Not all
1
5
Part No.
Part Name
203-1730Drive Belt
203-1739Twist ‘n Snap Hose
203-1751Brush Roll
3290Style 14 Pre-Motor Foam Filter
32076 Style 7 & 9 Post-Motor HEPA Media Filter*
27W8Style 7 & 9 Post-Motor Febreze® Filter
203-1729Inner Cyclone Assembly
203-1733Pet Strip Left and Right
parts are included with every model.
2
3
6
4
7
8
*The filter media, not the vacuum as a whole, complies with IEST-RP-CC001.5 HEPA standard.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
17
Accessories - Total Floors®
Item Part No. Part Name
1
203-1740Crevice Tool
2
203-7529 Pet TurboEraser Tool
3
203-1741 Pet Hair Fabric Tool
4
203-1228 Dusting Brush/Upholstery Tool
5
203-1368 Pet Contour Tool®
6
98Q1-A Shedaway® Pet Groom Attachment
7
203-2447 TurboBrush® Tool
8
203-1787Long Reach Dusting Tool
9
203-8296Furniture Tool
10
203-1768Extension Wand
*Not all parts are included with every model.
** Long Reach Dusting Tool and Furniture Tool available in Fall 2012
1
2
5
6
9
10
18
3
7
4
8
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Warranty –
BISSELL Total Floors® Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may vary
from state to state. If you need additional instruction regarding this warranty or have questions
regarding what it may cover, please contact BISSELL Consumer Care by E-mail, telephone, or
regular mail as described below.
Total Floors® 61C5 series – Limited Three Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product
BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL's
option, free of charge from the date of purchase by the original purchaser, for three years any
defective or malfunctioning part.
Total Floors® 52C2 series – Limited Four Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product
BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s
option, free of charge from the date of purchase by the original purchaser, for four years any
defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair,
or any other use not in accordance with the user's guide is not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact BISSELL Consumer Care.
Website or E-mail:
www.bissell.com
Or Call:
BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8 am - 10 pm ET
Saturday 9 am - 8 pm ET
Or Write:
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, MI 49501
ATTN: Consumer Care
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE
ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO THE WARRANTY DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow warranty limitations on how long an implied warranty last so the above
limitation may not apply to you.
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
19
Don't forget to register your product!
Registering is quick, easy and allows us to serve you better over the lifetime of your
product. You’ll receive:
BISSELL Reward Points
Automatically earn points for discounts and free shipping on future purchases.
Efficient Service
Supplying your information now saves you time should you need to contact us with
questions regarding your product.
Product Support Alerts
We’ll contact you with any important product alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!
Visit bissell.com/registration now!
BISSELL consumer care
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Care
1-800-237-7691
Monday - Friday 8 am — 10 pm ET
Saturday 9 am — 8 pm ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Care
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt.
It provides proof of purchase date in the event
of a warranty claim. See Warranty on pages
19 for details.
©2012 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Vietnam
Part Number 110-4563
Rev 5/12
Visit our website at:
www.bissell.com
20
w w w. b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1