ISYS® WALL MOUNT TOUCHPANELS

ISYS® WALL MOUNT TOUCHPANELS
Wall Mount Touchpanel Accessories
INTERFACE MODULES AND CABLES
TPMC-CH-IMW
CAT5 Balanced AV Interface Wall Plate
wall mount touchpanels
The TPMC-CH-IMW is a wall plate version of the
TPMC-CH-IMC interface module, providing a wall
plate connection for new Isys® TPS and TPMC-CH
series touchpanels that utilize Crestron Home® (CH)
CAT5 Balanced AV connectivity*. It mounts into a
2-gang electrical box and includes front panel
connections for a single “triamese” cable (provided
with the touchpanel or sold separately). Several
TPMC-CH-IMW wall plates may be installed to
facilitate connectivity for a single movable
touchpanel at multiple locations.
Wired as part of a complete Crestron Home
CAT5 AV distribution system, the TPMC-CH-IMW
requires just a single CresCAT-D cable, carrying
Cresnet, bidirectional audio, and (1) video signal
up to 500 feet within a single bundled cable (observe
distance limitations based upon power consumption
for the touchpanel in use). The TPMC-CH-IMW can
also be connected to conventional audio and coaxial
video sources.
Maximum Input Level: 4 VRMS balanced, 2 VRMS unbalanced
Connects to any Crestron CAT5 Audio port via CresCAT
cable, or a conventional audio source
AUDIO OUT: (1) 5-pin 3.5mm detachable terminal block
Balanced stereo line-level output (unbuffered pass-thru from
front AUDIO port);
Connects to any Crestron CAT5 Audio port via CresCAT
cable, or a conventional balanced audio input
LED Indicators
SPECIFICATIONS
PWR: (green) Indicates 24 Volts DC power supplied from
Cresnet control network
Connectors – Front Panel
Power Requirements
NET: (1) 4-pin 3.5mm detachable terminal block, pass-thru
from rear NET port
Cresnet Power Usage: 2 Watts
(0.08 Amps @ 24 Volts DC)
AUDIO: (1) 8-pin RJ45 female
Bidirectional CAT5 balanced stereo audio port
Output Impedance: 100 ohms balanced
Maximum Output Level: 2 VRMS
Input Impedance: Infinite (unbuffered pass-thru to rear AUDIO
OUT port)
VIDEO: (1) 8-pin RJ45 female
CAT5 balanced video output port
Output Impedance: 100 ohms balanced
Connectors – Rear Panel
NET: (1) 4-pin 5mm detachable terminal block;
Cresnet slave port, connects to Cresnet control network
VIDEO COMP/Y/Y, C/Pb, Pr: (1) 9-pin 3.5mm detachable
terminal block;
Provides (1) composite, S-Video, or component video input
Input Impedance: 100 ohms balanced (also accepts 75 ohm
unbalance);
Input Level: 1 VP-P nominal, 1.5 VP-P maximum
Maximum DC Offset: 1.5 Volts
Connects to any Crestron CAT5 Video Out port via CresCAT
cable, or a conventional coax video source
Environmental
Temperature: 41° to 122°F (5° to 50°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
2-gang mountable in a standard electrical box (2.5 inch
deep minimum); includes black metal front panel Decora®
inserts; requires Decora faceplate (provided by others)
Dimensions
Height: 4.11 in (10.44 cm)
Width: 3.50 in (8.89 cm)
Depth: 1.66 in (4.22 cm)
Weight
7.5 oz (0.21 kg)
*The TPMC-CH-IMW is not compatible with QuickMedia or 10-pin
RJ45 based systems.
AUDIO IN: (1) 5-pin 3.5mm detachable terminal block
Balanced/unbalanced stereo line-level input
Input Impedance: 20k ohm balanced, 10k ohm unbalanced
114
www.crestron.com | 800.237.2041 | 201.767.3400
© 2007 Specifications subject to change without notice
ISYS® WALL MOUNT TOUCHPANELS
Wall Mount Touchpanel Accessories
INTERFACE MODULES AND CABLES
TPS/TPMC-CBL-T
Triamese Cables for New Isys Touchpanels
The TPS/TPMC-CBL-T series of “triamese” cables
provides a clean, flexible cable solution for Crestron’s
new series of Isys 12", 15" and 17" touchpanels.
Available in 3, 6 and 9 foot lengths, these cables
are designed primarily for use in combination with
the TPMC-CH-IMC interface module. A single
TPS/TPMC-CBT-T cable may be used in place of
the 15 ft cable furnished with certain tilt model
touchpanels, and is also compatible with comparable
wall mount models wherever a short pre-made cable
solution is called for.
TPS/TPMC-CBL-T cables may also be used with
QuickMedia-based touchpanels to provide a clean
cable solution between the touchpanel and any
compatible QuickMedia interface device. These
cables are not compatible with older 10-pin RJ45
based touchpanels or interface modules.
AVAILABLE MODELS
TPS/TPMC-CBL-T3-B
wall mount touchpanels
Each triamese cable is composed of a single Cresnet
cable terminated on each end with a 3.5mm terminal
block connector, and two (2) CAT5e cables each
terminated with 8-pin RJ45 connectors, providing
connections for Cresnet data and power, plus
bidirectional audio and (1) video signal between the
module and the touchpanel.
3 foot (0.9 meters) Triamese Cable, Black
TPS/TPMC-CBL-T3-W
3 foot (0.9 meters) Triamese Cable, White
TPS/TPMC-CBL-T6-B
6 foot (1.8 meters) Triamese Cable, Black
TPS/TPMC-CBL-T6-W
6 foot (1.8 meters) Triamese Cable, White
TPS/TPMC-CBL-T9-B
9 foot (2.7 meters) Triamese Cable, Black
TPS/TPMC-CBL-T9-W
9 foot (2.7 meters) Triamese Cable, White
115
www.crestron.com | 800.237.2041 | 201.767.3400
© 2007 Specifications subject to change without notice
ISYS® WALL MOUNT TOUCHPANELS
Wall Mount Touchpanel Accessories
INTERFACE MODULES AND CABLES
ST-PK Programming Cable Kit
The ST-PK is a programming cable kit for SmarTouchTM
wireless touchpanels and most Isys® touchpanels.
It is used only for loading touchpanel files, updating
firmware, and configuring the touchpanel prior to
operation. The ST-PK may also be used to update
firmware and adjust the digital audio signal processing
in Crestron's 7.1 surround sound processors and
room solution boxes.
SPECIFICATIONS
wall mount touchpanels
Cables
3.5mm to RJ11 Cable Assembly (CNSP-585)
Provides connection between a SmarTouch wireless
touchpanel and the control processor via a RJ11 Cresnet
port; may require an additional CNRJ11 , ST-CNB, or
C2N-HBLOCK accessory.
RJ11-to-RJ11 Cable plus RJ11-to-DB9F
Adapter (STCP-502)
Provides connection between an Isys touchpanel,
surround processor, or room solution box RS-232
port and PC COM port.
116
www.crestron.com | 800.237.2041 | 201.767.3400
© 2007 Specifications subject to change without notice
ISYS® WALL MOUNT TOUCHPANELS
Wall Mount Touchpanel Accessories
MOUNTING KITS
BB
Back Boxes
BB-Series back boxes provide a recess-mounted
steel enclosure for Isys wall mount touchpanels.
Designed for pre-construction applications, these
back boxes permit fastening to the studs of a framed
wall prior to installation of sheet rock. An assortment
of knockouts is provided to accommodate conduit
fittings, and a blank cover plate is included with
each model.
AVAILABLE MODELS
BB-17L
BB-15L
AVAILABLE ACCESSORIES
Back Box for New Isys 15" Wall Mount Touchpanels
Touchpanel Models:
TPS-15L, TPS-15G-QM-L, TPMC-15-QM-L, TPMC-15-CH-L
Dimensions (HWD):
13.97 x 14.31 x 3.31 in (35.49 x 36.36 x 8.41 cm)
TMK
Trim Rings
BB-12L
Note: Dimensions shown do not include mounting brackets;
consult the installation manual for actual cutout dimensions,
clearances, and complete mounting instructions.
Back Box for New Isys 12" Wall Mount Touchpanels
Touchpanel Models:
TPS-12L, TPS-12G-QM-L
Dimensions (HWD):
12.17 x 13.75 x 3.31 in (30.92 x 34.92 x 8.41 cm)
BB-4000L
MMK
Mud Rings
wall mount touchpanels
Back Box for New Isys 17” Wall Mount Touchpanels
Touchpanel Models:
TPS-17L, TPMC-17-QM-L, TPMC-17-CH-L
Dimensions (HWD):
14.34 x 17.00 x 3.31 in (36.42 x 43.17 x 8.41 cm)
Back Box for Isys 10.4" Wall Mount Touchpanels
Touchpanel Models: TPS-4000L
Dimensions (HWD):
9.18 x 12.75 x 3.31 in (23.32 x 32.37 x 8.41 cm)
BB-3100L
Back Box for Isys 6.4" Wall Mount Touchpanels
Touchpanel Models: TPS-3100L
Dimensions (HWD):
6.69 x 9.34 x 3.31 in (16.97 x 23.73 x 8.41 cm)
BB-2000L
Back Box for Isys 5" Wall Mount Touchpanels
Touchpanel Models: TPS-2000L
Dimensions (HWD):
6.69 x 7.62 x 3.31 in (16.97 x 16.51 x 8.41 cm)
BB-4L
Back Box for Isys 3.6" Wall Mount Touchpanels
Touchpanel Models: TPS-4L
Dimensions (HWD):
5.79 x 6.93 x 3.31 in (14.71 x 17.60 x 8.41 cm)
117
www.crestron.com | 800.237.2041 | 201.767.3400
© 2007 Specifications subject to change without notice