16-289.fm Page 1 Tuesday, July 20, 1999 10:57 AM

Cat. No. 16-289

OWNER’S MANUAL

Please read before using this equipment.

13-Inch Color TV/Monitor

16-289.fm Page 2 Tuesday, July 20, 1999 10:57 AM

FEATURES

Your Radio Shack 13-Inch Color TV/

Monitor has many features for easy and convenient TV viewing. Your TV is specially designed for the hearingimpaired, with a built-in digital decoder that allows you to read closedcaptioned and text-service broadcasts.

You can also use your TV to monitor an audio/video source that has audio/ video outputs, such as a VCR or camcorder. The supplied remote control lets you operate the TV from a distance.

Your TV also includes these special features.

181-Channel Tuning Capability — lets you select up to 68 VHF/UHF channels and cable channels 1–125.

Automatic Channel Programming

— automatically stores in memory all active channels in your area for quick tuning.

Programmable Sleep Timer — automatically turns off your TV after the time you set.

Auto Demonstration — lets you review the TV’s set-up menus.

Bilingual On-Screen Display — lets you select English or Spanish for the on-screen language.

Automatic Picture Control — lets you select the factory preset picture so you do not need to manually adjust the picture controls.

Multicolored On-Screen Bar Graph

Displays — show the relative adjustment level for each picture control.

Earphone Jack — lets you connect an earphone so you can listen without disturbing others.

Note: You need two AA batteries (not supplied) to power the remote control.

For your records, we suggest you record your TV’s serial number here.

The number is on the back of the TV.

Serial Number _______________

2

© 1997 Tandy Corporation.

All Rights Reserved.

Radio Shack is a registered trademark used by Tandy Corporation.

16-289.fm Page 3 Tuesday, July 20, 1999 10:57 AM

SAFETY PRECAUTIONS

Power Supply: This TV operates on

120V, 60 Hz AC power only. Never connect the TV to a voltage other than the specified voltage (such as to the output of a nontransformer type converter or to direct current).

Polarized Plug: This TV is equipped with a polarized plug (one blade is wider than the other). This plug fits into an

AC power outlet only one way. If you are unable to fully insert the plug into the outlet, try reversing the plug.

Installation: Do not expose the TV to any unnecessary jarring, moisture, dust, direct sunlight, or heat.

Select a place for this TV that minimizes the length of the antenna lead and power cord.

Allow sufficient space between the TV and wall so the chassis components are properly ventilated.

Do not cover the ventilation slots on the top or back of the TV or place the

TV on any soft material that could affect ventilation on the bottom of the TV.

Warning: To prevent fire or shock hazard, do not expose this product to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

!

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

!

This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case.

This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product.

3

4

16-289.fm Page 4 Tuesday, July 20, 1999 10:57 AM

CONTENTS

Getting Started ..................................................................................................... 5

Choosing a Location ........................................................................................ 5

Connecting Antennas ...................................................................................... 5

Connecting an Outdoor Antenna .............................................................. 5

Connecting Cable TV ...................................................................................... 6

Connecting an Audio/Video Source ................................................................. 7

Connecting Power ........................................................................................... 7

Connecting Earphones .................................................................................... 7

Installing the Remote Control’s Batteries ........................................................ 8

Using the TV’s Controls ...................................................................................... 9

Using the TV’s Front Panel Controls ............................................................... 9

Using the Remote Control ............................................................................. 10

Using Auto Demonstration ............................................................................. 11

Operation ............................................................................................................ 12

Turning the TV On/Off ................................................................................... 12

Setting the On-Screen Language .................................................................. 12

Selecting the Input Signal .............................................................................. 12

Selecting TV or Video .................................................................................... 13

Using Automatic and Manual Channel Programming .................................... 13

Using Automatic Programming ............................................................... 13

Manually Adding a Channel .................................................................... 13

Manually Deleting a Channel .................................................................. 14

Auto Picture Control ...................................................................................... 15

Adjusting the Picture ...................................................................................... 15

Special Functions .............................................................................................. 17

Setting the Sleep Timer ................................................................................. 17

Using Closed Captions .................................................................................. 17

Selecting the Caption Function ............................................................... 19

Using the Text Function ................................................................................. 19

Selecting Text .......................................................................................... 20

Troubleshooting ................................................................................................. 21

Care and Maintenance ....................................................................................... 22

FCC Information ............................................................................................ 23

Specifications ..................................................................................................... 24

16-289.fm Page 5 Tuesday, July 20, 1999 10:57 AM

GETTING STARTED

CHOOSING A LOCATION

Choose a location for the TV where:

• Air flows freely on all sides.

• The power cord is not in the way of normal traffic.

Note: Do not plug in the power cord until you make all other connections.

CONNECTING

ANTENNAS

The supplied rod antenna provides adequate reception in most areas.

To connect the rod antenna, insert it into the hole on the top of the TV. Attach the 300-ohm twin-lead connectors to the two screw terminals on the supplied adapter.

300 Ohm Flat Wire

300-to-75 Ohm Adapter

Then connect the adapter to the TV’s

VHF/UHF (75

Ω

) terminal.

Rod Antenna

300-to-75 Ohm Adapter

VHF/UHF (75

Ω

) Terminal

Connecting an Outdoor

Antenna

For the best reception, we recommend you use an outdoor antenna.

Note: Before you connect the TV to an outdoor antenna, inspect the antenna and the antenna’s cable. Severely weathered antennas and antenna cables can reduce the signal quality.

Your local Radio Shack store sells replacement antenna cable (300-ohm flat wire or 75-ohm coaxial cable) and a wide variety of outdoor antennas.

The antenna connection you use depends on the type of antenna and cable you have.

Warning: When installing an outdoor antenna, read and follow all instructions and cautions that accompany the antenna.

• If you have a combination VHF/

UHF antenna and the antenna uses 75-ohm coaxial cable, connect the cable directly to the TV’s

VHF/UHF (75

Ω

) terminal.

VHF/UHF Antenna

VHF/UHF (75

Ω

) Terminal

75 Ohm Coaxial Cable

5

16-289.fm Page 6 Tuesday, July 20, 1999 10:57 AM

6

• If you have a combination VHF/

UHF antenna and the antenna uses 300-ohm flat wire, connect the flat wire to the screw terminals on the supplied 300-to-75 ohm adapter. Then connect the adapter to the TV’s VHF/UHF (75

Ω

) terminal.

VHF/UHF (75

Ω

) Terminal

VHF/UHF Antenna

300-to-75 Ohm Adapter

300 Ohm Flat Wire

CONNECTING CABLE TV

If you subscribe to a cable TV service, connect the cable company’s 75-ohm coaxial cable directly to the TV’s VHF/

UHF (75

Ω

) terminal.

If you use a cable box, connect the box’s output to the TV’s VHF/UHF (75

Ω

) terminal.

From Cable Company

75-Ohm Coaxial Cable

IN OUT

Cable Box

• If you have separate VHF and

UHF antennas, use a VHF/UHF combiner (not supplied) to combine the VHF and UHF signals.

Then connect the combiner’s 75ohm connector to the TV’s VHF/

UHF (75

Ω

) terminal.

VHF Antenna

UHF Antenna

VHF/UHF (75

Ω

) Terminal

VHF/UHF Combiner

Set the TV to the same channel as the box’s output (Channel 3 or 4) and use the box to select channels.

Note to CATV System Installer: This reminder is provided to call the CATV system installer’s attention to Section

820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

You can listen to your TV by connecting an earphone to the TV’s EAR-

PHONE jack, or by connecting the TV’s

AUDIO IN/VIDEO IN jack s to a home audio system.

16-289.fm Page 7 Tuesday, July 20, 1999 10:57 AM

CONNECTING AN

AUDIO/VIDEO SOURCE

You can use your TV to monitor an audio/video source (such as a VCR, camcorder or laser disc player). Connect the audio/video source’s output jacks to the AUDIO IN/VIDEO IN jacks on the back of the TV.

AUDIO IN

VIDEO IN

CONNECTING

EARPHONES

For private listening, plug a pair of earphones with a 1 /

8

-inch mini-plug (not supplied) into the EARPHONE jack on the right side of the TV.

EARHONE

To view the audio/video source, follow the steps in “Selecting TV or Video” and play the audio/video source according to its instructions.

Note: If you use the EARPHONE jack, use the TV’s VOLUME control to adjust the volume.

CONNECTING POWER

Plug the TV’s AC power cord into a standard AC power outlet.

Listening Safely

To protect your hearing, follow these guidelines when you use earphones.

• Set the volume to the lowest setting before you begin listening. After you begin listening, adjust the volume to a comfortable level.

• Do not listen at extremely high volume levels. Extended highvolume listening can lead to permanent hearing loss.

• Once you set the volume, do not increase it. Over time, your ears adapt to the volume level, so a volume level that does not cause discomfort might still damage your hearing.

7

16-289.fm Page 8 Tuesday, July 20, 1999 10:57 AM

INSTALLING THE

REMOTE CONTROL’S

BATTERIES

The remote control requires two AA batteries (not supplied) for operation.

For the longest battery life, use alkaline batteries (Radio Shack Cat. No.

23-552). To ensure consistent operation, change the batteries about once a year.

Batteries

8

1. Remove the battery compartment cover by pressing down and sliding it in the direction of the arrow.

2. Install two AA batteries as indicated by the polarity markings (+ and –) inside the compartment.

Cautions:

• Batteries installed incorrectly might leak and damage the remote control.

• Do not mix old batteries with new ones, and do not mix different types of batteries (for example, standard and alkaline).

3. Replace the cover.

16-289.fm Page 9 Tuesday, July 20, 1999 10:57 AM

USING THE TV’S CONTROLS

USING THE TV’S FRONT PANEL CONTROLS

This section briefly describes the function of each button on the TV’s front panel.

Each function is described in detail later in this manual.

Remote Control Receiver

FUNCTION — Selects the different onscreen function controls.

VOL — Press the top VOL button to increase the volume and bottom VOL button to lower it. The number of vertical bars at the lower part of the screen indicates the relative volume level. You also use these buttons to adjust the

TV’s on-screen function controls.

CH — Press the top CH button to select the next higher channel and the bottom CH button to select the next lower channel. Press and hold down either button to quickly scroll through channels. See “Using Automatic and

Manual Channel Programming” on

Page 13.

POWER — Turns on or off the TV.

9

16-289.fm Page 10 Tuesday, July 20, 1999 10:57 AM

USING THE REMOTE

CONTROL

The remote control has the same controls as the TV’s front panel, as well as the additional controls described in this section.

To operate the remote control, point its front window toward the TV’s front panel. Then press the desired button(s) on the remote control.

Channel Selection Buttons

Channel Selection (Number) But-

tons — Press to directly select a channel. The selected channel number appears on the screen for about 5 seconds.

• To select a single-digit broadcast

(AIR) channel — Channel 5, for example — press 5 . You do not need to press 0 before entering a single-digit channel (but, if you do, the TV changes channels faster).

• To select a double-digit broadcast channel — Channel 12, for example — press 1 and then 2 .

• To select a three-digit cable channel — Channel 121, for example

— press 1 , 2 , and 1 .

Note: You must select CABLE as the input source before you can select a cable channel. See “Selecting the Input Signal” on

Page 12.

RECALL — Displays the current channel number for about 5 seconds. Also clears the on-screen function displays.

SLEEP — Sets the sleep timer.

PICTURE — Selects a picture control

(contrast, brightness, color, tint, or sharpness) for adjustment.

TV/VIDEO — Selects the TV or VIDEO mode.

CAPTION — Turns the closed caption decoder on or off.

10

16-289.fm Page 11 Tuesday, July 20, 1999 10:57 AM

REVIEW — Returns to the previously selected channel.

MUTE — Press once to mute the sound. MUTE appears on the screen.

Press again to restore the sound.

APC (Auto Picture Control) — Returns to the factory preset picture settings or the settings you select.

SET-UP — Selects the different onscreen function controls. (This button is similar to the FUNCTION button on the TV; however, it only performs setup operations.)

USING AUTO

DEMONSTRATION

Auto demonstration lets you see all the on-screen controls.

1. Press SET-UP on the remote control until AUTO DEMO.

appears on the screen.

2. Press VOL + or – to start the demonstration. The screen shows the different controls and adjusts them so you can see how each one works.

When the demonstration reaches the last display, it starts again from the beginning.

3. To stop auto demonstration, press any button on the remote control or front panel. The picture returns to the settings selected before the demonstration.

11

16-289.fm Page 12 Tuesday, July 20, 1999 10:57 AM

OPERATION

TURNING THE TV

ON/OFF

Press POWER on the TV’s front panel or remote control to turn the TV on or off.

SETTING THE ON-

SCREEN LANGUAGE

1. Press SET-UP on the remote control or FUNCTION on the front panel until LANGUAGE appears on the screen.

SELECTING THE INPUT

SIGNAL

Follow these steps to select between receiving cable stations and receiving broadcast channels.

1. Press SET-UP on the remote control or FUNCTION on the front panel until INPUT SELECTION appears on the screen.

2. Press VOL + or – so the arrow points to ENGLISH or ESPANOL

(Spanish).

3. The on-screen display automatically clears in about 5 seconds.

Or, you can press RECALL to clear it.

All on-screen displays are now in the selected language.

Note: When you press SET-UP on the remote control, VIDEO does not appear as a selection. Press

TV/VIDEO on the remote control to select VIDEO (see “Selecting TV or Video” on Page 13).

2. Press VOL + or – so the arrow points to AIR , CABLE , or VIDEO .

Select AIR if you are using an antenna or CABLE if you are using a cable service. Select VIDEO to view the audio/video source connected to the TV’s input jacks.

3. The on-screen display automatically clears in about 5 seconds.

Or, you can press RECALL to clear it.

12

16-289.fm Page 13 Tuesday, July 20, 1999 10:57 AM

SELECTING TV OR

VIDEO

Press TV/VIDEO on the remote control to view the selected input signal ( TV ) or the audio/video source connected to the TV’s input jacks ( VIDEO ).

3. Press VOL + or –. The TV automatically scans and memorizes all active channels in your area.

USING AUTOMATIC AND

MANUAL CHANNEL

PROGRAMMING

When you turn on the TV for the first time, use the automatic channel programming feature to scan and memorize all active broadcast and cable channels in your area. If there are additional channels you want to add or delete, you can manually add or delete them.

Using Automatic

Programming

1. Press TV/VIDEO so TV is selected.

2. Press SET-UP on the remote control or FUNCTION on the front panel until AUTO PROGRAM appears on the screen.

Note: You can press any button on the remote control or front panel to stop automatic programming.

When the TV has scanned and stored all active channels, it stops on the nearest programmed channel to where you started.

Now, when you press CH + or –, the TV skips inactive channels.

Note: If the TV is unplugged for more than 24 hours, you must repeat automatic channel programming to restore channels in memory.

Manually Adding a Channel

To add a channel that was not stored during automatic programming, follow these steps.

1. Press TV/VIDEO so TV is selected.

13

16-289.fm Page 14 Tuesday, July 20, 1999 10:57 AM

2. Select the input signal ( AIR or

CABLE ).

3. Use the remote control’s number button(s) to select the channel you want to store.

Manually Deleting a Channel

If the TV stored a channel you do not want, follow these steps to delete the channel from memory.

1. Press TV/VIDEO so TV is selected.

2. Select the input signal ( AIR or

CABLE ).

4. Press SET-UP on the remote control until the channel number,

ADD , and DELETE appear on the screen.

3. Press CH + or – or the remote control’s number button(s) to select the channel you want to delete.

5. Press VOL + or – so the arrow points to ADD .

6. The on-screen display automatically clears in about 5 seconds.

Or, you can press RECALL to clear it. The channel is added.

4. Press SET-UP on the remote control until the channel number,

ADD , and DELETE appear on the screen.

14

16-289.fm Page 15 Tuesday, July 20, 1999 10:57 AM

5. Press VOL + or – so the arrow points to DELETE .

6. The on-screen display automatically clears in about 5 seconds.

Or, you can press RECALL to clear it. The channel is deleted.

appears. If you want to return to the picture controls you previously selected, press APC until PICTURE RESET

OFF appears.

ADJUSTING THE

PICTURE

Follow these steps to adjust the picture’s contrast, brightness, color intensity, tint, and sharpness.

1. Press PICTURE on the remote control or FUNCTION on the front panel until the desired picture control appears.

2. Adjust the selected control level by pressing VOL + or –.

AUTO PICTURE

CONTROL

Press APC on the remote control to display the Auto Picture Control status.

When PICTURE RESET is set to ON , the TV’s picture shows the factory settings. If you adjust the picture, ON automatically changes to OFF (see

“Adjusting the Picture”).

If you have adjusted the picture and want to return to the factory settings, press APC until PICTURE RESET ON

The bar graph on the screen shows the relative adjustment level.

15

16-289.fm Page 16 Tuesday, July 20, 1999 10:57 AM

Refer to the following picture control chart.

CONTROL

CONTRAST

BRIGHTNESS

COLOR INTENSITY

TINT

SHARPNESS

CONTROL

BUTTON

– +

Lower

Darker

Higher

Brighter

Lighter Deeper

Reddish Greenish

Softer Sharper

16

16-289.fm Page 17 Tuesday, July 20, 1999 10:57 AM

SPECIAL FUNCTIONS

SETTING THE SLEEP

TIMER

You can set the sleep timer to automatically turn off the television after the selected time period.

Follow these steps to use the sleep timer.

1. Press SLEEP on the remote control until the desired time period appears on the screen: --,

240 , 210 , 180 , 150 , 120 , 90 ,

60 , 30 , 20 , or 10 minutes.

SLEEP---

SLEEP10

SLEEP24

SLEEP210

SLEEP20

SLEEP30 SLEEP60

...

2. Wait about 5 seconds for the display to automatically clear. The timer begins to count down for the selected number of minutes.

Notes:

• To view the remaining sleep time, press SLEEP once. After about 5 seconds, the display clears.

• To cancel the sleep timer, press

SLEEP until the display shows

SLEEP --. After about 5 seconds, the display clears.

USING CLOSED

CAPTIONS

Closed captioning displays the audio portion of a television program as written words that appear on the television screen (in a form similar to English subtitles). Closed captions allow viewers to read the dialogue and narration of television programs.

Caption signals are transmitted as part of the TV broadcast and then decoded by the TV to display as words.

Caption Tips

• Sometimes TV stations broadcast two different caption signals on the same channel. By selecting

MODE 1 or MODE 2 under MODE

SELECTION , you can choose which signal to view. MODE 1 is usually the signal with the captions, while MODE 2 might show demonstration or programming information.

• Not all TV broadcasts include closed caption signals. Check your local programming guide.

17

16-289.fm Page 18 Tuesday, July 20, 1999 10:57 AM

18

• Your TV might not properly receive caption signals in the following situations.

Ignition: Black spots or horizontal streaks appear; picture flutters or drifts. Usually caused by interference from an automobile ignition system, neon lamps, drills, or other electrical appliances.

Ghosts: Double images appear.

Ghosts are caused by the television signal following two paths: the direct path and another reflected from a building, hill, or other object.

Changing the direction or position of the antenna might improve the reception.

Snow: Small dots in the picture. If your TV is located at the fringe area of a television broadcast, where the signal is weak, you might need to install a special antenna to improve the picture.

You are using an old, bad, or illegally recorded tape in the VCR connected to the TV.

An airplane or car is interfering with the TV signal.

The signal from the antenna is weak.

The program wasn’t captioned when it was produced, transmitted, or taped.

• If you connect a VCR that has a captioning function, note the following.

For the best reception of caption signals, connect a signal distributor as shown.

75-Ohm Antenna Jack

CATV Output Terminal

Signal Distributor

Back of TV

Antenna Input Terminal

Back of VCR

TV Input Terminal

16-289.fm Page 19 Tuesday, July 20, 1999 10:57 AM

Select the caption function for either the TV or the VCR, but not both. If both are decoding caption signals, captions might overlap or reception might be poor.

Selecting the Caption

Function

1. Press CAPTION on the remote control or FUNCTION on the front panel so DECODER appears.

Then press VOL + or – so the arrow points to ON .

4. To turn off captions, press CAP-

TION or FUNCTION so DECODER appears, then press VOL + or – so the arrow points to OFF .

Note: If you select captioning and then turn off the TV, captioning is still active when you turn on the TV again.

2. Press CAPTION or FUNCTION so

DECODER MODE appears. Then press VOL + or – so the arrow points to CAPTION .

USING THE TEXT

FUNCTION

Text is information presented in a black box on the television screen as a service to viewers. Some examples of text broadcasts are captioned program lists, weather forecasts, stock exchange reports, and wire-service news.

3. Press CAPTION or FUNCTION until

MODE SELECTION appears.

Press VOL + or – so the arrow points to MODE 1 or MODE 2 .

Some television stations provide two different text services. You can choose between the two text signals by selecting MODE 1 or MODE 2 under MODE

SELECTION .

Note: Not all television stations provide text services.

19

16-289.fm Page 20 Tuesday, July 20, 1999 10:57 AM

Selecting Text

1. Press CAPTION on the remote control or FUNCTION on the front panel to display DECODER . Then press VOL + or – so the arrow points to ON .

Note: If the signal for the text program is weak, the black box might appear and disappear on the screen. This problem goes away when reception improves.

2. Press CAPTION or FUNCTION so the display shows DECODER

MODE . Then press VOL + or – so the arrow points to TEXT .

3. Press CAPTION or FUNCTION so the display shows MODE SELEC-

TION and press VOL + or – so the arrow points to MODE 1 or MODE

2 .

4. To turn off the text function, press

CAPTION or FUNCTION so DE-

CODER appears, then press VOL

+ or – so the arrow points to OFF .

20

16-289.fm Page 21 Tuesday, July 20, 1999 10:57 AM

TROUBLESHOOTING

If you have problems with your 13-inch Color TV/Monitor, review the suggestions below. If you cannot eliminate the problem, contact your local Radio Shack store for assistance.

Problem Suggestion

No power.

No picture or sound.

Sound is OK; picture is poor.

Poor reception.

Make sure the power cord is plugged in

Make sure the television is turned on.

Try another channel.

Check the Air, Cable, or Video setting.

Check all connections.

Try another channel (station trouble).

Check all connections.

Adjust the picture controls.

Adjust the antenna.

Check all connections.

Lines in picture or ghosts (multiple images).

Might be local interference.

Try another channel (station trouble).

Adjust the antenna.

Adjust the picture controls.

Check all connections.

Might be local interference.

Remote control doesn’t work.

Check batteries in the remote control.

Cannot tune to the desired channel.

Try another channel (station trouble).

Check the Air, Cable, or Video setting.

Channel might not be programmed in channel memory. Store it using auto or manual programming.

21

16-289.fm Page 22 Tuesday, July 20, 1999 10:57 AM

CARE AND MAINTENANCE

Your Radio Shack 13-Inch Color TV/Monitor is an example of superior design and craftsmanship. The following suggestions will help you care for your TV/Monitor so you can enjoy it for years.

Keep the TV/Monitor dry. If it gets wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits.

Handle the TV/Monitor gently and carefully. Dropping it can damage circuit boards and cases and can cause the TV/Monitor to work improperly.

Use and store the TV/Monitor only in normal temperature environments. Temperature extremes can shorten the life of electronic devices and distort or melt plastic parts.

Keep the TV/Monitor away from dust and dirt, which can cause premature wear of parts.

CLEANER

Wipe the TV/Monitor with a damp cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the TV/Monitor.

Modifying or tampering with the TV/Monitor’s internal components can cause a malfunction and might invalidate your TV/Monitor’s warranty and void your FCC authorization to operate it. If your TV/Monitor is not performing as it should, take it to your local Radio Shack store for assistance.

22

16-289.fm Page 23 Tuesday, July 20, 1999 10:57 AM

FCC INFORMATION

This TV/Monitor complies with the limits for a Class B digital device as specified in Part 15 of

FCC Rules

. These limits provide reasonable protection against radio and TV interference in a residential area. However, your TV/

Monitor might cause TV or radio interference even when it is operating properly. To eliminate interference, you can try one or more of the following corrective measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the

TV/Monitor and the radio or TV.

• Use outlets on different electrical circuits for the TV/Monitor and the radio or TV.

Consult your local Radio Shack store or an experienced radio/TV technician if the problem still exists.

You must use shielded cables with this equipment.

23

16-289.fm Page 24 Tuesday, July 20, 1999 10:57 AM

SPECIFICATIONS

System ....................................................................................................... NTSC-M

Picture Tube ....................................................................... Type No. A34KPU02XX

Horizontal Resolution ............................................................................... 260 Lines

Receiving Channels ............................................................. Broadcast VHF: 2

∠

13

Broadcast UHF: 14

∠

69

CATV: 1

∠

125

Intermediate Frequency .......................... Picture IF Carrier Frequency: 45.75 MHz

Sound IF Carrier Frequency: 41.25 MHz

Color Sub-Carrier Frequency: 42.17 MHz

Maximum Sensitivity .................... VHF: 28 dB

µ

V max; UHF/CATV: 32 dB

µ

V max

Antenna .................................................................. VHF/UHF 75-Ohm Unbalanced

Power Source ................................................................................. AC 120V, 60Hz

Power Consumption ........................................................................ 85 W Maximum

Output Power ................................................................................. 1.2 W Maximum

Load Impedance ....................................................................................... 16 Ohms

Frequency Response ............................................. 80 Hz–7 kHz (3 dB Bandwidth)

Total Harmonic Distortion ................................................................................... 2%

Speaker ............................................................... 16 Ohm 1.5 Watt (Maximum 3W)

Input Level:

Video .................................................................... 1 Vp-p (75-Ohm Terminated)

Audio ............................................................................................. 400 mV rms

Dimensions (HWD) .............. 14 3 /

4

×

14 6 /

7

×

14 2 /

9

Inches (375

×

377.5

×

361.5 mm)

Weight ......................................................................................... 17 lb 8 oz (7.9 kg)

Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.

24

16-289.fm Page 25 Tuesday, July 20, 1999 10:57 AM

NOTES

25

16-289.fm Page 26 Tuesday, July 20, 1999 10:57 AM

26

16-289.fm Page 27 Tuesday, July 20, 1999 10:57 AM

27

16-289.fm Page 28 Tuesday, July 20, 1999 10:57 AM

RADIO SHACK LIMITED WARRANTY

This product is warranted against defects for 90 days from date of purchase from Radio

Shack company-owned stores and authorized Radio Shack franchisees and dealers.

Within this period, we will repair it without charge for parts and labor. Simply bring your

Radio Shack sales slip as proof of purchase date to any Radio Shack store. Warranty does not cover transportation costs. Nor does it cover a product subjected to misuse or accidental damage.

EXCEPT AS PROVIDED HEREIN, RADIO SHACK MAKES NO EXPRESS WARRAN-

TIES AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURA-

TION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

We Service What We Sell

9/94

1A7

RADIO SHACK

A Division of Tandy Corporation

Fort Worth, Texas 76102

P/N 482-H59L

Printed in Mexico