- Sports & recreation
- Fitness, gymnastics & weight training
- Treadmills
- Exerpeutic
- Magnetic Treadmill 4010.6-120116
- Owner's manual
Exerpeutic Magnetic Treadmill 4010.6-120116 Owner's Manual
Add to My manuals20 Pages
Exerpeutic 4010 is a magnetic treadmill designed for home use, with features to help you achieve your fitness goals. Its sturdy construction supports users up to 300lbs, and its user-friendly computer tracks time, distance, calories burned, and heart rate. It also offers preset programs and manual mode to customize your workout. With its space-saving design and transport wheels, the Exerpeutic 4010 can be easily folded and moved for storage when not in use.
advertisement
4010.6-120116
Magnetic Treadmill
OWNER’S MANUAL
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
If you need help with product information, assembly, or replacement parts. Please contact customer service.
Email us at:
[email protected]
Or call us at:
1-844-641-7920
Hours:
8:00 am to 5:00 pm (PST) Daily
TABLE OF CONTENTS
SERVICE ------------------------------------------------------------------------- 2
LABEL PLACEMENT -------------------------------------------------------- 3
PRODUCT SAFETY ----------------------------------------------------------- 4
OVERVIEW DRAWING ------------------------------------------------------ 5
PARTS LIST --------------------------------------------------------------------- 6
PARTS LIST & TOOL---------------------------------------------------------- 7
ASSEMBLY ---------------------------------------------------------------------- 8
COMPUTER --------------------------------------------------------------------- 11
STORAGE ----------------------------------------------------------------------- 12
ADJUSTMENTS ---------------------------------------------------------------- 13
LUBRICATION ------------------------------------------------------------------ 15
TROUBLE SHOOTING & MAINTENANCE ----------------------------- 16
WARRANTY -------------------------------------------------------------------- 17
PARTS REQUEST FORM --------------------------------------------------- 18
1
SERVICE
IMPORTANT: FOR NORTH AMERICA ONLY
For damage or defective product, questions, replacement parts or any other service support, please contact our customer service department
(8:00 AM - 5:00 PM Pacific Standard Time, Daily) by below methods:
For Best Service Email:
[email protected]
*
Website:
www.paradigmhw.com
Toll-Free:
1-844-641-7921**
Please have the following information ready when requesting for service:
Your name
Phone number
Model number
Serial number
Part number
Proof of Purchase
For damaged or defective product please contact our customer service before returning to the store.
* Emailing us with the information above will be the best method to receive a response during peak business hours.
**Response time may vary.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA
2
LABEL PLACEMENT
3
PRODUCT SAFETY
Basic precautions should always be followed, including the following safety instructions when using this magnetic treadmill: Read all instructions before using this magnetic treadmill.
1. Check every part of the equipment before exercise. If there is any defective component, replace it immediately; keep the equipment out of use until repair.
2. Make sure all parts, bolts and nuts are well assembled and locked before exercise.
3. Never insert any object into any opening.
4. Never operate this magnetic treadmill if it is not working properly. If it has been dropped or damaged, or been exposed to water, do not use and consult an Authorized Service Representative at 1-844-641-7921.
5. Do not attempt any maintenance or adjustments other than those described in this manual. Should any problems arise, discontinue use and consult an Authorized Service Representative.
6. Wear comfortable and suitable clothing when using the treadmill. Do not use the treadmill barefoot, in only socks or in sandals, always wear athletic shoes. Never wear loose clothing because it could run the risk of getting caught in the treadmill.
7. Keep children and pets away from the equipment while in use.
8. Do not use the treadmill outdoors. This magnetic treadmill is for household use only.
9. Only one person should be on the treadmill while in use.
10. Keep the magnetic treadmill on a solid, level surface with the minimum safety area clearance of 78.7” x 118” of the magnetic treadmill. Be sure the area around the treadmill remains clear during use and has adequate clearance.
11. Hold the handlebar with your hands when starting or stopping exercise and increasing or decreasing the speed.
12. If feeling chest pains, nausea, dizziness, or short of breath, you should stop exercising immediately and consult your physician before continuing.
13. The maximum weight capacity for this product is 300lbs / 136kgs.
WARNING:
Before beginning any exercise program consult your physician. This is especially important for the persons who are over 35 years old or who have pre-existing health problems. Read all instructions before using any fitness equipment.
CAUTION:
Read all instructions carefully before operating this
product. Retain this Owner’s Manual for future reference.
4
OVERVIEW DRAWING
5
PARTS LIST
No. Description
001 Main Frame
002 Incline Adjuster
003L Left Stabilizer Tube
003R Right Stabilizer Tube
004 Stabilizer
005 Handlebar
Qty No. Description
1 034 Handlebar End Cap
1 035 Bolt M8x50
1 036 Nylon Washer Ø20xØ9.5x2.5
1 037 Washer Ø16xØ8.5x1.5
1 038 Washer Ø20xØ10.5x1.5
1 039 Bolt M10x60
006 Computer
007 Computer Support Plate
1 040 Bolt M8x15
1 041 Rubber Pad Ø32x8.8
008 Hand Pulse Sensor Extension
Wire
1 043 Wire Plug Ø12.5
009 Extension Sensor Wire II [Short] 1 044 Bolt M8x40
010 Hand Pulse Sensor with Wire 2 045 Incline Adjuster Round Cap Ø25
011 Extension Sensor Wire I [Long] 1 046 Bolt M8x45
013 Tension Control Knob 1 048 Cap 13#
014 Magnet Bracket
015 Magnet
1 049 Rear Roller Adjustment Bolt M6x80 2
5 050 Elliptic End Cap 30x70 2
2
2
2
2
6
4
2
016 Washer Ø13xØ6.5x1.5
017 Bolt M8x70
018 Nylon Nut M8
019 Nut M6
1 052 Rear Roller Ø42x419
1 053 Bearing Cap Ø42
6 054 Bearing 6201
1 055 Washer Ø16xØ12.3
1
2
4
2
Qty
2
2
4
10
2
2
024 Round Knob M10x25
025 Ball Knob Ø25xM8
026 Spring Knob Pin
027 Spring Ø12x1x37
1 056 Big Washer Ø24xØ13.2x2.0
1 057 Rear Roller Axle Ø12x466
1 058 Front Roller Axle Ø12x586
1 059 Clip
028 Handlebar Knob Ø48xM10
029 Nut M8
2 060 Front Roller Ø42x509
2 061 Anti-slip Pad
030 Handlebar Knob Pin Ø12xM8x58 2 062 Running Belt
031 Computer Knob M5x15 2 063 Side Rail
032 Bolt M5x12
033 Handlebar Foam Grip
8 064 Running Deck
2 065 Phillips Self Drilling Screw
1
2
1
2
2
1
1
2
1
6
6
No. Description
066L Left Protective Cover
066R Right Protective Cover
067 Transport Wheel
068 Small Magnet
070 Screw ST4.2x20
071 Rubber Pad Ø33x18
072 Cable Clip
073 Bolt M5x10
PARTS LIST & TOOL
Qty No. Description Qty
1 074 Big Washer Ø20xØ6x1.5
1 075
Socket Button Head Cap Screw
M6x55
2 076 Spring Ø8xØ50x1
1
1
1
1 077 Sensor with Wire
2 078 Screw ST4.8x10
2 079 Plastic Washer Ø25xØ13x2
1
1
2
1 080 Wire Plug
1 081 Self-Tapping Screw ST 4.2x12
2
1
5mm Allen Wrench with Phillips
Screwdriver
1 PC
7
ASSEMBLY
Tool:
5mm Allen Wrench with Phillips
Screwdriver
Step 1
Place the magnetic treadmill in the upright position.
Remove six Washers (37) and six Bolts (40) from the Left/Right Stabilizer
Tubes (3L, 3R with the 5mm Allen Wrench with Phillips
Screwdriver provided.
Insert both Left/Right Stabilizer Tubes (3L, 3R) into the Stabilizer (4), and secure using six Washers (37) and six Bolts (40) that were removed.
Tighten the bolts with the 5mm Allen Wrench with Phillips Screwdriver provided.
8
ASSEMBLY
Step 2
Remove the Round Knob (24) from the Stabilizer (4).
Place one hand on the rear end of Main Frame (1) and use the other hand to pull out the Ball Knob (25). Lower the Main Frame (1) down onto the floor.
TO PREVENT INJURY PLEASE MAKE SURE YOU HAVE A FIRM HOLD
WHEN SETTING DOWN THE DECK.
Remove two Computer Knobs (31) from the Computer Support Plate (7).
Remove two Handlebar Knobs (28) from the Handlebar (5) and then lift the
Handlebar (5) all the way up.
Tighten the Handlebar (5) onto the Stabilizer (4) with two Handlebar Knobs
(28) that were removed.
Turn the Computer (6) upwards and adjust the angle of Computer (6) to the desired position. Hold the Computer (6) and align computer knob holes.
Tighten the Computer (6) onto the Handlebar (5) with two Computer Knobs
(31) that were removed.
9
ASSEMBLY
Step 3
Install Round Knob (24) to the bigger hole on the Stabilizer (4) and Main
Frame (1) by turning it in a clockwise direction to lock the Main Frame (1) in place.
Note: Securely tighten Round Knob (24) so that the treadmill is sturdy.
Plug the Hand Pulse Sensor Extension Wire (8) from the Handlebar (5) into
PULSE receptacle on the back of Computer (6).
Plug the Extension Sensor Wire II (9) from the Handlebar (5) into SENSOR
INPUT receptacle on the back of Computer (6).
10
COMPUTER
Specifications:
TIME ----------------00:00-99:59 MIN: SEC
DISTANCE -------- 0.00-9999 MI
CALORIES --------0.0-9999 CAL
ODOMETER ----- 0-9999 MI
PULSE ------------- 40-240 BEATS/MIN
Button functions:
MODE: Display function selection.
SET: To set goal values as exercise target.
RESET: To clear goal values.
Display functions:
SCAN
Automatically scans through each display mode at 6-second intervals.
TIME
Displays Times.
SPEED
Displays the current speed.
DISTANCE
Displays distance of exercise sessions.
CALORIES
Displays calories burned during exercises.
ODOMETER
Displays accumulative distance from combined exercise sessions.
PULSE
Display the BPM (Beats per Minutes).
Set a goal value:
You can set an exercise goal, the value will be counted down for the value you set.
Press MODE to select a value you’d like to set.
Press SET to set the value, then start your exercise.
How to install the batteries:
1. Remove the battery cover at the rear of computer.
2. Place two "SIZE-AA" batteries into the battery housing.
3. Insure batteries are correctly positioned and battery springs are in proper contact with batteries.
4. Re-install the battery cover.
5. If the display is illegible or only partial legible, remove batteries and wait 15 seconds before reinstalling.
11
STORAGE
Round Knob (24) shall be positioned here when Main Frame (1) is lifted up in the upright position.
Remove Round Knob (24) from the Stabilizer (4) and Main Frame (1).
Hold the rear end of the Main Frame (1) by one hand and use the other hand to pull out the Ball Knob (25). Lift the Main Frame (1) up and align spring knob pin hole. Release the Ball Knob (25) until the Spring Knob Pin (26) pop into the hole on the Main Frame (1) to lock the Main Frame (1) in place.
CAUTION: Failure to secure the Main Frame (1) with the Spring
Knob Pin (26) may cause the treadmill accidental fall and cause bodily injury.
Install the Round Knob (24) onto the Main Frame (1).
Remove two Handlebar Knobs (28) from the Handlebar (5) and then push the Handlebar (5) all the way down.
Install two Handlebar Knobs (28) back onto the Handlebar (5) to lock the
Handlebar (5) in place.
Remove two Computer Knobs (31) from the Computer Support Plate (7).
Turn the Computer (6) downwards and align computer knob holes.
Tighten the Computer (6) onto the Handlebar (5) with two Computer Knobs
(31) that were removed.
12
ADJUSTMENTS
Adjusting the Tension Control Knob
To increase the load, turn the tension control knob in a clockwise direction.
To decrease the load, turn the tension control knob in a counterclockwise direction.
Adjusting the Incline
There are 3 incline angles (A: 8%,
B: 10%, C: 12%) that the incline adjuster can be set to. Place one hand on the rear end of the main frame, then lift the rear end of the main frame up and use your other hand to adjust the Incline adjuster to the desired position.
About the Running Belt
Keeping the Belt aligned
This belt is 16 inches wide. It is recommended that the user’s footsteps stay on the central 12 inches area. This will prevent the belt from shifting off the center. Note: Continuously stepping on the edge of the Belt will cause the Belt to shift to either side of the bed.
Anti-slip Pad
Tension Control Knob
Anti-slip Pad
12 inches of Suggested
Running Area.
13
Adjusting the Running Belt
ADJUSTMENTS
1. The running belt is initially set and adjusted at the factory. However it may come loose during transportation and/or during use. After prolonged use, the belt will begin to stretch out.
2. If the running belt begins to shift to either left or right side, the user can stand on the Anti-slip Pads and hold the handlebar with both hands. Then use your right or left foot to run on the side of the running belt that is opposite to the direction of the slip.
3. If the belt begins to slip to the left use your right foot on the right side. You should see the belt start to correct itself by moving back towards the center.
4. However, if the running belt is still shifting away from center, use the 5mm Allen
Wrench provided and turn the left or right Rear Roller Adjustment Bolt 1/2 turn in a clockwise direction (turn the same side bolt that matches the direction of the slip).
Then try running on the center of the running belt again. If the running belt is still shifting away from center, turn the same Rear Adjustment Bolt another 1/4 turn in the clockwise direction. You should see the belt start to correct itself by moving back towards the center.
Repeat this procedure until the running belt is centered.
If the running belt is slipping during use, then use the 5mm Allen Wrench provided and turn both the left and right rear roller adjustment bolts 1/4 turn in the clockwise direction. You should now run on the running belt to determine if the running belt is still slipping. Repeating the above procedure until the running belt is not slipping.
14
The treadmill has already been spread with "Silicone Oil" in advance before leaving the manufacturing plant. Silicone oil is without volatility and has gradually permeated through the running belt. There will be no need to re-spread the oil in normal circumstances. "Silicone Oil" may be re-spread once the resistance has been increased and the running belt starts rubbing against the running deck. To hold open the running belt from two sides, apply the silicone oil with an even motion on the center of the running deck. Allow the silicone oil to
‘set’ for one minute before using the magnetic treadmill.
Attention: Only use "Silicone Oil" lubricants for this equipment. In addition, do
not add any other oil ingredient; otherwise the magnetic treadmill will be damaged. Do not over-lubricate the running deck. Excess lubricant
should be wiped off with a clean towel.
15
TROUBLE SHOOTING & MAINTENANCE
TROUBLE SHOOTING
PROBLEM: Treadmill running belt slips or is not centered on rear roller.
SOLUTION: Refer to the “Adjustments” section on page 15.
PROBLEM: Computer not working correctly
SOLUTION: Check to make sure the computer wires are connected securely.
SOLUTION: Check the batteries are correctly positioned and battery springs are proper contact with batteries.
SOLUTION: Make sure the batteries are not dead.
PROBLEM: There is no heart rate reading or heart rate reading or is erratic / inconsistent.
SOLUTION: Make sure that the wire connections for the hand pulse sensors are secure.
SOLUTION: To ensure the pulse readout is more precise, please always hold on to the handlebar grip sensors with two hands instead of just with one hand only when you try to test your heart rate figures.
SOLUTION: Gripping the hand pulse sensors too tight. Try to maintain moderate pressure while holding onto the hand pulse sensors.
PROBLEM: The magnetic treadmill makes a squeaking noise when in use.
SOLUTION: The bolts may be loose on the magnetic treadmill, please inspect the bolts and tighten the loose ones.
MAINTENANCE
Cleaning
The magnetic treadmill can be cleaned with a soft cloth and mild detergent. Do not use abrasives or solvents on plastic parts. Please wipe your perspiration off the magnetic treadmill after each use. Be careful not get excessive moisture on the computer display panel as this might cause an electrical hazard or electronics to fail. Please keep the magnetic treadmill, specially, the computer console, out of direct sunlight to prevent screen damage. Please inspect all assembly bolts on the machine for proper tightness every week.
Storage
Store the magnetic treadmill in a clean and dry environment away from children.
16
WARRANTY
MANUFACTURER’S LIMITED WARRANTY
Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s
Manual. Paradigm’s obligation under this warranty applies to the following:
COMPONENT LENGTH OF WARRANTY
Structural Frame 3 years
All Other Components 90 days
(computer display, electronics, upholstery, foam, ball bearings, pulleys, belts, cables, wires, shocks, covers, tension, internal mechanism, wheels, pedals, knobs, accessories and hardware)
Exclusions from Warranty Coverage:
Paradigm does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:
1. Improper installation and/or failure to abide by Paradigm’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it was not designed;
3. Cosmetic items such as scratches, dents or discolorations;
4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
5. Any act of Nature (such as fire, flooding, snow, ice, hurricane, earthquake, lightning or other natural disaster), environmental condition (such as air pollution, mold, mildew, etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
6. Normal weathering due to exposure to sunlight, weather and atmosphere which can cause colored surfaces to, among other things, flake, chalk, or accumulate dirt or stains; or
7. Improper operation, alteration, handling, storage, abuse or neglect of the products.
Paradigm, using its sole discretion, will either repair or replace free of charge any part(s) proven to be defective under normal home use. Any repair or replacement shall provide no new warranty coverage, but shall retain only the remaining portion of the original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required.
Ordering Replacement Parts
Replacement parts can be ordered by emailing our customer service department:
[email protected]
Open Daily 8:00 AM - 5:00 PM (PST).
When ordering replacement parts please have the following information ready:
1. Owner’s Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase
17
6
PARTS REQUEST FORM
Paradigm Health & Wellness, Inc.
EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO
[email protected]
*
NAME: _______________________________________________________
ADDRESS: ____________________________________________________
CITY ______________ STATE ______________ ZIP ___________________
TELEPHONE: (Day) ____________________________________________
(Night) ____________________________________________
SERIAL#: _____________________________________________________
MODEL#: _____________________________________________________
PURCHASE DATE: _____________________________________________
PLACE OF PURCHASE: _________________________________________
PART # DESCRIPTION QTY
“YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS”
* This form can also be faxed in Fax #: 626-810-2166
18
advertisement
Related manuals
Frequently Answers and Questions
What is the maximum weight capacity of the treadmill?
How do I assemble the treadmill?
How do I adjust the incline of the treadmill?
How do I set a goal value for my workout?
How do I replace the batteries in the computer?
What is the SCAN function?
How do I fold the treadmill for storage?
advertisement