Taurus T9.9 - Treadmill Owner Manual

Assembly and operating instructions

Art. No. TF-T99-2

Treadmill

T9.9

2

T9.9

T9.9

Dear Customer,

Thank you for deciding for a high-quality training equipment of the brand Taurus, the brand that makes athlete‘s hearts beat faster. Taurus offers a wide range of home fitness equipment like elliptical cross trainers, ergometers, treadmills and rowing machines. Taurus equipment is the optimal equipment for all those who want to train at home independent of goals and fitness level. For further information please visit www.sport-tiedje.com or www.taurus-fitness.de.

SAFETY NOTICE

Please read all of the instructions carefully before assembly and first use. These instructions are intended to ensure speedy assembly and explain safe usage. Make sure that all people exercising with the equipment (in particular children and persons with limited physical, sensory, mental or motor capabilities) are informed about these instructions and its content in advance.

In case of doubt, a responsible person must supervise the use of the equipment.

This equipment has been manufactured according to the latest safety knowledge. As far as possible, potential safety hazards which could cause injury have been eliminated.

Make sure to follow the instructions carefully and that all parts are securely in place. If required, read through the instructions again to correct any mistakes.

Please pay close attention to the safety and maintenance instructions given here.

The contract partner cannot be held liable for damage to health, accidents or damage to the equipment when it is not used in accordance with these instructions.

The equipment is suitable for home use as well as semi-professional use (e. g., hospitals, clubs, hotels, schools, etc.). It is not suitable for commercial or professional use (e. g., commercial gyms).

Retain these instructions in a safe place for future reference, maintenance or when ordering replacement parts.

3

CONTENTS

1 GENERAL INFORMATION

1.1 Technical data

1.2 Personal safety

1.3 Electrical safety

1.4 Set-up place

2 ASSEMBLY INSTRUCTIONS, MAINTENANCE AND CARE

2.1 General instructions

2.2 Errors and error diagnosis

2.3 Error codes and troubleshooting

2.4 Care and maintenance

2.5 Maintenance and service calendar

3 ASSEMBLY

3.1 Package contents

3.2 Assembly instructions

4 OPERATING INSTRUCTIONS

4.1 Console display

4.2 Button functions

4.3 Turning on the equipment

4.4 Programs

4.4.1 Manual program

4.4.2 Training program

4.4.3 Random program

4.4.4 Heart rate controlled programs

4.4.5 User-defined programs

4.4.6 Body fat mode

4.4.7 APP (iOS & Android) installation manual

5 WORKOUT INSTRUCTIONS

5.1 Heart rate measuring

5.2 10 tips for effective running training

5.3 Designing a workout

4

T9.9

18

31

32

33

26

26

28

28

18

20

23

25

41

41

44

45

10

10

11

12

12

14

15

15

16

6

8

9

6

7

T9.9

5.4 Stretching exercises for leg & chest muscles

5.5 Workout journal

6 WARRANTY INFORMATION

7 DISPOSAL

8 ORDERING ACCESSORIES

9 ORDERING SPARE PARTS

9.1 Service hotline

9.2 Serial number and model name

9.3 Parts list

9.4 Exploded drawing

47

49

50

52

53

54

54

54

55

60

5

1

GENERAL INFORMATION

1.1

Technical data

LCD display of

+ speed in km/h

+ training time in min

+ training distance in km

+ calories burnt in kcal

+ heart rate (when using the hand sensors or a chest strap)

+ incline in %

+ intensity profile

+ device connection

+ graphic display of trained muscles

Motor output: 3 HP continuous output (DC motor)

Max. motor continuous output: 2.2 kW / 3 HP

Max. motor peak rating: 5.5 kW / 7.5 HP

Max. load of incline motor: 350 kg/771 lbs

Speed range: 0.8 - 20 km/h

Incline range: 0 - 15 %

Total number of training programs: 15

Pre-set programs:

Manual program:

Heart rate controlled programs: 3

Random program:

User-defined programs:

1

4

6

1

Running surface size (L x W): 157.5 x 55 cm

Wheel diameter: 76 mm

Running belt thickness: 4.4 mm (orthopedic running belt)

Running deck thickness: 25,4 mm

Weight and dimensions:

Article weight (gross, including packaging): 156 kg

Article weight (net, without packaging): 131 kg

Packaging dimensions (L x W x H): approximately 2260 mm x 1000 mm x 420 mm

Setup dimensions (L x W x H): approximately 2075 mm x 920 mm x 1375 mm

Maximum user weight: 180 kg/396 lbs

6

T9.9

T9.9

1.2

Personal safety

+ Before you start using the equipment, you should consult your physician that this type of exercise is suitable for you from a health perspective. Particularly affected are persons who: have a hereditary disposition to high blood pressure or heart disease, are over the age of 45, smoke, have high cholesterol values, are overweight and/or have not exercised regularly in the past year.

+ Please note that working out excessively can seriously damage your health. Please also be aware that heart rate monitoring systems might be imprecise.

+ The equipment may only be used for its intended purpose; that means for running training by adults.

+ Any other usage is prohibited and potentially dangerous. The contract partner cannot be held liable for damage resulting from improper use.

+ The equipment is strictly for use by one person at a time.

+ Children should not be allowed unsupervised access to the equipment.

+ Before starting your training, make yourself familiar with all of the equipment‘s functions and setting options. Have an expert explain the correct usage of the product to you.

+ Make sure that nobody is in the range of motion of the equipment while exercising.

+ Keep your hands, feet and other body parts, hair, clothing, jewelry and other objects well clear of moving parts.

+ During use, wear suitable sports clothing rather than loose or baggy clothing.

When selecting sports shoes, think about the suitability of the sole – preferably this should be made of rubber or other non-slip materials. Shoes with heels, leather soles, studs or spikes are not suitable. Never work out in bare feet.

+ It is also important to take note of the information given in the workout instructions for creating a workout plan.

+ At the first signs of weakness, nausea, dizziness, pain, difficulty in breathing or other abnormal symptoms, stop your workout immediately and, if necessary, consult your physician.

+ Without prior agreement from your authorized contract partner, opening the equipment is prohibited.

+ The equipment has stable steps on the sides that you can stand on in case of an emergency and leave the equipment.

+ The safety key should be inserted during all training.

+ The safety key and the power cable should be removed when you are not present in order to rule out improper usage by third parties.

7

Safety Key

+ The equipment has an EMERGENCY STOP mechanism for your safety. The equipment may only be operated when the safety key is properly attached to the contact point of the cockpit. The equipment will automatically stop immediately if the safety key is no longer on the contact point. That is why you should attach the safety key string with the clip to your clothing before training. Remove the safety key from the cockpit with the help of the string if you would like to quickly stop the treadmill, you can no longer handle the speed or an emergency occurs.

+ In order for the safety key to be released from the cockpit contact point in the event of a fall, the clip from the safety key must be attached to your clothing!

+ An uncontrolled usage of the equipment by third parties can be avoided by removing and storing the safety key.

+ Prevent children from having access to the safety key.

1.3

Electrical safety

+ The equipment requires a 220 - 240V / 50 Hertz mains power supply.

+ The equipment should be connected directly to a grounded plug socket only by means of the power cable supplied. The use of multi-socket adapters or similar is not recommended. Extension leads must comply with local electrical safety guidelines. Always fully unwind the power cable.

+ The outlet should be secured with a fuse with a minimum value of „16 amperes, slow“.

+ In order to reduce the risk of an electric shock, always unplug the equipment from the mains socket immediately after your workout, before assembly or dismantling, and before maintenance or cleaning. Do not pull on the cable.

+ When plugged in, do not leave the equipment unattended at any time. To avoid use by anyone unfamiliar with the operating instructions, the power cable should be removed when the equipment is not in use.

+ Keep the power cable away from heat, oil and sharp edges. Do not route the power cable underneath the equipment or under a carpet or rug, and do not place any objects on top of it.

+ Make no modifications to either the power cable or the mains plug.

+ If the power cable or the plug are damaged or defective, contact your authorized contract partner. Do not use the equipment in the meantime.

+ Do not keep electrical devices (e. g., mobile phones) in close proximity to the console or the control electronics, otherwise display values (e. g., pulse measuring) could be inaccurate.

8

T9.9

T9.9

1.4

Set-up place

+ The equipment should only be used indoors, in a sufficiently heated and dry area

(ambient temperature between 10°C and 35°C). The equipment should not be used outdoors or in rooms with high humidity (over 70%) like swimming pools. The equipment should only be stored in surroundings with an ambient temperature between 5°C and 45°C.

+ The training room should be well ventilated during training and not be exposed to any draughts.

+ Choose a location in which to place the equipment such that there is enough free space/clearance to the front, the rear and to the sides of the equipment (at least

1.50 m). Furthermore, the equipment should not be set up in main entrances or on escape routes.

+ Always keep the power cable away from hot surfaces and grounds and make sure that the cable is not stuck somewhere or becomes a „trip hazard“.

+ No objects of any type should be inserted into the openings of the equipment.

+ The equipment should be placed on a level and solid surface, any unevenness in the floor should be leveled out.

+ A floor protective mat / equipment underlay can help to protect high-quality floor

2 coverings (parquet, laminate, cork, carpets) from dents and sweat and can help to level out slight unevenness.

9

2

ASSEMBLY INSTRUCTIONS, MAINTENANCE AND CARE

2.1

General instructions

+ Please check if all parts and tools belonging to the equipment are included in the delivery and if there is any transport damage. If there are any complaints, please contact your contract partner directly.

+ Some of the nuts and bolts to be used in assembly are already pre-mounted in order to make set-up as easy as possible.

+ The equipment must be assembled by adults. In case of doubt, ask for assistance from another person with technical skills.

+ Keep children away from the equipment during assembly, because small parts are included in the delivery and may be swallowed.

+ Make sure that you have enough space (at least 1.50 m) in every direction during assembly.

+ Do not leave any tools and packaging materials like plastic sheeting laying around to avoid danger of suffocation for children.

+ Assemble the equipment on an underlay mat or on the cardboard packaging in order to avoid damage to the equipment and to the floor (scratches).

+ Before starting assembly, all individual parts should be placed on the floor next to each other.

+ Read the assembly instructions carefully and assemble the equipment according to the illustrations. Proceed carefully and cautiously.

+ First loosen all parts and check for their correct fitting. Then tighten the screws using a tool.

+ Modifications to the design or improper repairs may pose a hazard to the user and should not be carried out. The product warranty may be void as a result.

+ Only authorized service technicians are permitted to carry out all servicing and/or repairs – it excludes maintenance and care.

+ Damaged or worn components may impair your safety and the lifespan of the equipment. You should therefore immediately replace damaged or worn components. Please contact your contract partner in such a case. The equipment should no longer be used until it has been repaired. When needed, only use original Taurus spare parts.

+ Check the tightness of all screw connections once a month.

+ In order to be able to guarantee the constructively defined safety level of this equipment, we recommend having the equipment regularly maintained (at least once a year) by specialists (service technicians of your contract partner).

10

T9.9

T9.9

+ The equipment may be cleaned of dust, dirt and sweat using a damp cloth. The use of solvents should be strictly avoided. Also, make sure that no liquids (e. g. sweat) get into the openings of the equipment (e. g. console).

2.2

Errors and error diagnosis

The equipment runs through regular quality controls during production. Nevertheless, errors or malfunctions on the equipment may occur. Individual parts are often the cause of faults and replacement is usually sufficient. Please use the following overview to see the six most common errors and how to repair them. If the equipment still does not work properly, please contact your contract partner.

Error

Console only shows lines

Running belt slips through/stops

Scraping noises

Display does not show anything

Cause

Safety key missing

Belt tension/lubrication not ok

Running belt scrapes, because it is not aligned

Check plug connections

(cables)

Sources of interference in the room

Repair

Check if the safety key is inserted and place it in

Align running belt in accordance with the instructions

Check belt tension/lubrication in accordance with the instructions

Align running belt in accordance with the instructions

Mains switch on “on”, make sure that the safety key is inserted

Remove sources of interference (e. g. mobile phone, speakers, etc.)

No pulse display

With chest strap

Unsuitable chest strap

Use suitable chest strap (see

recommended accessories)

Position of the chest strap incorrect

Reposition chest strap and/or moisten electrodes

Batteries empty Change batteries

11

2.3

Error codes and troubleshooting

The electronic system from the treadmill executes tests continually. If there are deviations, an error code will be displayed and the normal operation will be stopped for your safety.

Please contact your contract partner for technical customer service.

+ E1 - Speed value cannot be recorded. Either the motor is broken or the signal cannot be transmitted.

+ E6 - Incline values are incorrect. The incline motor is broken or the signal cannot be transmitted.

+ E7 - Incline AD is above the normal value. The incline motor is broken or an incorrect setting was made.

2.4

Care and maintenance

The most important maintenance measure is taking care of the running belt. It includes the adjustment, tensioning and lubrication of the running belt. Damage caused due to a lack of care or negligence will not be covered by the warranty. Thus, check for maintenance in regular intervals. Be extremely careful when adjusting and tensioning the belt, because a strong over or under tension may cause damages. The running belt is set properly in the factory before delivery. However, the running belt may get out of place during transport.

Aligning the running mat

+ During training, the running belt should run as centered and straight as possible.

The alignment of the running belt may change depending on the stress and load.

Another reason can be the positioning of the equipment on an uneven surface.

+ While adjusting the belt, let the equipment run with a speed of approximately

5km/h. Nobody may be on the equipment during this process.

+ If the running belt is offset to the left, turn the left setting screw on the rear end of the equipment at most 1/4 rotation clockwise and the right setting screw at most

1/4 rotation counterclockwise (fig. C).

12

T9.9

+ If the running belt is offset to the right, turn the right setting screw on the rear end of the equipment at most 1/4 rotation clockwise and the left setting screw at most

1/4 rotation counterclockwise (fig. D).

+ Then watch how the belt runs for approximately 30 seconds, because the change will not be visible immediately.

+ Repeat the process until the running belt runs straight again. If the running belt cannot be adjusted, please contact your contract partner.

T9.9

Tensioning the belt

+ If the running belt slips over the rollers during operation (if this is the case, a noticeable jerking will be noticed while running), the running belt must be tightened again. In most cases, the cause for the slipping is a straining of the belt through usage. This is completely normal.

+ It can be tightened through the same setting screws that were used during alignment.

+ While tensioning the belt, let the equipment run with a speed of 5km/h.

+ Turn the left and right setting screws directly after each other a max. of 1/4 rotation clockwise.

+ Then check if the running belt is still slipping. If this is still the case, the described process needs to be repeated.

13

Lubricating the running belt

+ If the running belt is inadequately lubricated, the friction will increase significantly and this leads to strong wear of the endless belt, running panel, motor and circuit board.

+ If you feel an increase in friction from the running belt, this is an indicator that you should lubricate the belt (however, a lubrication should be done at least every three months).

+ The treadmill has a reminder for lubricating the treadmill: A symbol is displayed on the console every 100 operating hours. The symbol appears on the display for five minutes and then turns off. In order to turn off the symbol prematurely, press the

INCLINE up and INCLINE down buttons at the same time.

+ In order to be able to optimally lubricate the treadmill, the running belt must be lifted slightly. Then apply some silicone spray on the entire running deck. Apply three short (approximately 1 second) sprays of silicone lubricant between the belt and the running deck.

+ The spraying tube should be held sideways in order to guarantee a moistening of the entire underside of the belt. Continue to rotate the belt by hand so that the entire area between the endless belt and running deck is lubricated. Wipe off the excess lubricant.

+ This maintenance must also be executed after the equipment has not been used for a longer period of time.

2.5

Maintenance and service calendar

The cockpit, casing, handrails and entire frame must be cleaned after every training session with a moist towel (no solvent!) in order to avoid damage caused by sweat.

After 150 hours of operation, the maintenance symbol reminds you to clean the treadmill. After you have cleaned the treadmill and checked all components, turn off the symbol by simultaneously pressing the INCLINE up and INCLINE down buttons.

14

T9.9

T9.9

The following routine work must be done in the specified time intervals:

Part

Display console

Belt tension

Belt lubrication

Weekly

Plastic covers

Screws & cable connections

Legends: C = cleaning; I = inspect c c

Monthly 2x annually Annually

I

I

I

I

I

3

ASSEMBLY

3.1

Package contents

The package contains the parts represented in the illustration, including a power cable with mains plug. If one of the illustrated parts is missing, please contact your contract partner.

A

Part Description

A Console

B

Frame

C

Handrail (left)

D

Handrail (right)

E

Console mast (left)

F

Console mast (right)

G

Cover (left)

H

Cover (right)

I

Bottle

1

1

1

1

Qty.

1

1

1

1

1

B

C

D

G

E

H

F

I

15

Part Description a Hexagon screw

M8xP1.25x75

b Cross-headed screw

M5xP0.8x15

c Hexagon screw

M8xP1.25x20

d Screwdriver 8mm x

200mm e Allen key 5mm x

70mm x 70mm f

Safety key g

Silicone

Qty.

8 a

6

8

1

1

1

1 e f b g c d

3.2

Assembly instructions

Before starting assembly, look carefully through the individual assembly steps shown and assemble the equipment in the order indicated.

Step 1: Assembly of the handrails

Turn the console (A) and connect the control cables of the left (C) and right (D) handrails with the cables from the console (A). The logo sticker must show outwards.

After you have assembled the handrails on the console, mount the parts with four screws (c).

16

T9.9

T9.9

Step 2: Assembly of the upright side frame

Guide the control cable that comes out of the base frame through the left side frame (C) from the bottom to the top. In order to make this step easier for you, a wire was already led through the side frame (C), which is mounted on the upper and lower end of the side frame. Loosen the wire on the lower end and attach the control cable to it. Now pull it upwards with the help of the wire. In order to prevent the control cable from sliding down, mount it in the upper area of the side frame (C) with the wire. Now plug the left side frame (C) into the left adapter of the base frame (B) and mount this then with the screws (c). Then proceed exactly the same for the right upright side frame (D). Once you have tightened all screws (a), press the cover caps (f) onto the heads of the screws.

Step 3: Assembly of the cockpit

Connect the console cable (A) first with the cable from the left console mast (E) and mount the console on the left and right console mast (E and F) with four screws (c). Then tighten the screws (a) in order to mount the console masts on the frame. Finally, mount the left and right cover (G and H) on the frame

(B) with six screws (b).

17

4

OPERATING INSTRUCTIONS

4.1

Console display

18

T9.9

T9.9

1

2

3

4

Time

Beats per minute and age

Heart rate zones

Training profile

5

Calories

Note on calorie measuring:

The calculation of calorie consumption is based on a general formula. It is not possible to exactly determine an individual calorie consumption, because diverse personal data is required for this. In order to allow for an approximation of your actual energy consumption, you can enter your body weight for this model.

6

7

Equipment connection status

Weight/distance

8

9

LCD text display

Speed

10

Muscle zone

11

Incline

Energy saving mode

If the treadmill is not used for more than four minutes, it will turn into energy saving mode. If you would like to use the treadmill again, remove the safety key and insert it again.

Muscle display

When the treadmill starts, the body and muscle lines will light up. If the user changes the incline, the stressed muscle groups will light up.

19

4.2

Button functions

STOP

20

QUICK START

- Press this button in order to immediately start with the training.

- Press this button during a break in order to return to the start mode.

- Press this button during training in order to get to the pause mode. The display shows “PAUSE”, the defined pause time is four minutes. If more than four minutes are needed, the system will go into the standby mode and the screen turns off the background lighting.

- Press this button in the pause mode for four seconds in order to stop the training and to get to the standby mode.

- Press this button in the menu mode in order to return to the main menu.

T9.9

T9.9

INCLINE up/ down

ENTER

MODE

SPEED INSTANT KEY

1 / 2 / 4 / 6 / 8 / 10

INCLINE INSTANT KEY

2 / 4 / 6 / 8 / 10 / 12

- Press this button and adjust the incline of the treadmill in increments of 1. If you hold the button, the value will change quicker.

- With this button, you can confirm your settings and get to the next step.

- Press this button during the start/ready status in order to enter programs.

- Set the speed of the treadmill with these direct buttons. The unit is in kmh or mph.

- Set the incline of the treadmill in degrees with these direct buttons.

Remove the safety key in the fitness or standby mode. An arrow pointing down will appear in the middle window. Each value indicates the standard value of zero.

Treadmill motor and program stop immediately and the incline remains in the angle before you removed the safety clip. The user must insert the safety clip again and the treadmill can be used again. The windows automatically set the sides to zero.

After you have turned on the equipment with the ON/OFF switch on the motor cover, the display will show a blinking heart symbol. In order to begin a predefined training program, select a corresponding training profile (WORKOUT PROGRAM). Press the

QUICK START button to immediately begin training without a training program.

Handrail buttons

S P E E D

+/-

INCLINE

+/-

Press this button and adjust the speed of the treadmill in

0.1 increments. If you hold the button, the value will change quicker.

Press this button and adjust the incline of the treadmill in increments of 1. If you hold the button, the value will change quicker.

21

Heart rate training

Hand pulse sensors: If the user grabs the hand pulse sensors during training, the pulse symbol will light up in the heart rate window. The current heart rate is recorded and displayed within 20 seconds.

Wireless pulse receiver: For safety reasons and for the purpose of a correct display, the use of a chest strap as a pulse transmitter is recommended instead of handle sensors starting at a speed of 7.2 km/h (4.5 mph). The wireless sensor transfers the pulse directly to the system.

The normal heart rate is between 40 and 220 heartbeats per minute (BPM). If you can choose between the hand pulse sensors and the chest strap, please prefer to use the chest strap.

AGE

21

22

23

24

18

18

20

13

14

15

16

17

28

29

30

25

26

27

31

32

BPM

H Basis

197 124

196 124

195 123

194 122

193 122

192 121

191 121

190 120

189 119

188 119

187 118

186 118

185 117

184 116

183 116

182 115

181 115

181 114

180 113

179 113

AGE

L

124 36

124 37

123 38

122 38

122 40

121 41

121 42

120 43

119 44

119 45

118 46

118 47

117 48

116 49

116 50

115 51

115 52

114 53

113 54

113 55

170

169

168

167

166

165

164

163

162

162

161

160

159

158

157

BPM

H Basis

175 110

174

173

172

171

110

109

109

108

103

103

102

101

101

100

100

99

107

107

106

106

105

104

104

AGE

L

110 59

110 60

109 61

109 62

108 63

107 64

107 65

106 66

106 67

105 68

104 69

104 70

103 71

103 72

102 73

101 74

101 75

100 76

100 77

99 78

22

92

91

91

90

94

93

92

BPM

Basis

97

96

95

95

94

90

90

90

90

90

90

90

90

T9.9

L

92

91

91

90

94

93

92

97

96

95

95

94

88

87

86

89

89

88

86

85

148

147

146

145

144

143

143

H

153

152

151

150

149

142

141

140

139

138

137

136

135

T9.9

33

34

35

178 112

177 112

176 111

112 56

112 57

111 58

156

155

154

98

98

97

98 79

98 80

97

134

133

90

90

85

84

Charging through USB

This equipment can be used for a Bluetooth connection. The user can communicate with the treadmill through the special APP. This opening is used to charge batteries from IOS or Android sets. The outgoing current is 1 A.

4.3

Turning on the equipment

(1) The default weight value is 70 kg (150 lbs). As soon as you change the weight (23 to

120 kg/50 to 286 lbs), the program will be executed corresponding to the weight setting.

(2) The display leads you through the setting steps.

(3) The STOP button can be pressed at any time in order to delete the setting and return to the previous window.

(4) The entered values are counted down to zero during training. Then the program is complete.

(5) Press QUICK START in the start/ready mode and it will take you to the manual mode.

(6) After you have started the program, the treadmill will adjust to the speed and incline in accordance with the program.

(7) The incline system from the treadmill corresponds to the important safety rules listed below.

+ If you press STOP, the system will go into the pause mode. The main motor and incline motor stop immediately. If you press QUICK START, you return to the status before the pause mode.

+ As soon as the program is complete or the time has reached the maximum value of

99:59 minutes, a warning signal will sound and the treadmill will stop in the “Run end” status.

+ If the incline is not at the zero level in the start/ready status, press STOP for two seconds or QUICK START to start the treadmill. The incline automatically returns to zero.

23

(8) If the incline goes back to zero, the incline motor can be stopped by removing the safety key.

(9) If you are in the PAUSE mode for four minutes, the program will end. If you hold

STOP, you can end the training and return to the Start/Ready mode.

Standby

As soon as the treadmill is turned on, a “beep” will sound and the window to enter the weight will appear after two seconds.

Weight setting

(1) Press SPEED+ or SPEED- to enter the weight. The default value is 70 kg (154 lbs).

The input range is between 23 to 130 kg (50 to 286 lbs).

(2) Confirm the weight with ENTER. “SELECT PROGRAM” appears on the screen. Press

SPEED+ or SPEED- in order to select a program. Optionally, you can press QUICK

START in order to directly begin training.

The reason for the weight setting is to show the user the burnt calories and to show the fitting formula for the change. The weight can be entered during any restart. After training or as soon as the safety key is removed, the equipment will go back to the weight setting page.

Rest mode: If the equipment is not used for a longer period of time, the computer will go into rest mode. The system goes into standby mode and turns off the screen lighting in order to save electricity. If you press a button in the rest mode, the screen will lighten up again.

24

T9.9

Quick start mode - beginning of training

(1) Press ENTER in standby mode in order to confirm the weight. Press QUICK START in order to start the training directly. “READY GO” appears on the display and after three seconds, the program starts at a speed of 0.8 km/h (0.5 mph), the incline is zero, the training time starts at 0:00, the maximum value is 99:59.

(2) During training:

+ Set the incline angle with INCLINE up or INCLINE down or INCLINE QUICK KEY.

+ Set the speed with SPEED+ or SPEED- or SPEED QUICK KEY.

T9.9

(3) Press STOP while training in order to get to the pause mode. The speed returns to zero and the incline stops at the current angle.

(4) If the training time is achieved 99:59 or one of the target values for time, distance or calories in this time, the speed will return to zero, the incline stops at the current angle, the screen shows “RUN END”. If you press STOP for four seconds or longer, the system will return to the standby mode.

4.4

Programs

You can select one of the following program categories:

• Manual program:

• Different profiles for pre-set training programs:

• Heart rate controlled programs:

• User-defined training programs:

• Random training program:

• Body mass mode

3

4

1

6

1

25

4.4.1

Manual program

(1) Confirm the manual program with ENTER and enter the time: Press SPEED+ or

SPEED- in order to set the target time. The default value is 0:00 min:sec and you can choose between 20:00 to 99:00.

(2) Confirm the time with ENTER and enter the distance: Press SPEED+ or SPEED- in order to set the target distance. The default value is 0.00 km (mile) and you can choose between 1.00 to 99.00.

(3) Confirm the distance with ENTER and enter the calories: Press SPEED+ or SPEED- in order to set the target calories. The default value is 0 calories, range 10 to 9990.

(4) As soon as you have completed the settings, press START and the program will accept the entered values as a guideline. As soon as the default values are at zero, the program is complete.

4.4.2

Training program

P1 to P6 profiles - There is a total of 30 levels, 1 minute per level

Program P1 (9-hole) - 3.5 km

(1) Confirm the program selection P1 with ENTER. Press SPEED+ or SPEED- in order to enter the level. The default value is 1, the range is between 1 to level 10.

(2) Confirm the target distance with ENTER. “Ready Go” appears on the screen and training begins after three seconds.

P1 (9 hole)

Program P2 (hill climbing)

(1) Confirm the program selection P2 with ENTER. Press SPEED+ or SPEED- in order to enter the level. The default value is 1, the range is between 1 to level 10.

(2) Confirm the selected level with ENTER. Press SPEED+ or SPEED- in order to enter the time. The default value is 30:00 min:sec; the range is between 20:00 to 99:00.

(3) Confirm the target time with ENTER. “Ready Go” appears on the screen and training begins after three seconds.

26

T9.9

T9.9

P2 (climbing)

Program P3 to P6: Setting corresponds to P2

P3 (hill run)

P4 (interval)

P5 (rolls)

P6 (weight reduction)

27

4.4.3

Random program

(1) Confirm the program selection RANDOM with ENTER. Press SPEED+ or SPEED- in order to enter the time. The default value is 0:00 min:sec; the range is between

20:00 and 99:00.

(2) Confirm the time with ENTER. Press SPEED+ or SPEED- in order to enter the distance. The default value is 0.00 km (mile). The range is between 1.00 and 99.00.

(3) Confirm the distance with ENTER. Press SPEED+ or SPEED- in order to enter the target calories. The default value is 0 calories; the range is between 10 to 9990.

(4) After you have completed the settings, press START to begin the training.

Note: Time, distance, calories can be entered. As soon as one of the values is entered, the other two automatically go back to zero.

RANDOM - random speed

4.4.4

Heart rate oriented programs

The training goal from this program is the heart rate. If the average exceeds the defined value, the incline and speed remain the same and the heart rate moves in the range in order to achieve the training goal. This heart rate program offers three types:

60%, 75% and the target heart rate (personal setting).

HRC 1-3 (heart rate 1-3)

Confirm the program selection HRC 1-3 with ENTER. Press SPEED+ or SPEED- in order to enter the desired heart rate: 60%, 75%, target heart rate.

28

T9.9

T9.9

Note: In the HRC mode, only a wireless pulse signal can be received. Wear a wireless chest strap. If the system does not receive a pulse signal for longer than 45 seconds, the system will stop automatically and displays “NO PULSE”. Hold STOP for four minutes and the system will return to the standby mode.

During the program, the speed decreases or increases every 10 seconds in accordance with the current pulse. If the current pulse is less than the target pulse, the speed will increase 0.1 kmh (mph). If the current pulse is higher than the target pulse, the speed will decrease 0.1 kmh (mph). If the speed increases 10 times, the incline will increase by one level. If the speed decreases 10 times, the incline will decrease by one level.

The maximum speed can be achieved. The speed can achieve the lowest value of 0.8 km/h (0.5 mph). The maximum incline level is 15.

(1) 60% and 75%

+ Confirm the selection 60% with ENTER. Press SPEED+ or SPEED- in order to enter the time. The default value is 0:00 min:sec. The range is between 20:00 and 99:00.

+ Confirm the time with ENTER. Press SPEED+ or SPEED- in order to enter the age.

The default value is 30. The range is between 13 and 80 years.

+ Confirm the age with ENTER. The heart rate window displays the age and calculates the target value based on the heart rate formula.

+ Confirm the target pulse with ENTER. “Ready Go” appears on the screen for three seconds and the training begins.

+ After the program starts, the current pulse will be displayed in the heart rate window and the target heart rate window shows the target heart rate.

HRC 60 % (heart rate 60 %)

29

HRC 75 % (heart rate 75 %)

(2) Target heart rate (THR)

+ Confirm the program THR with ENTER. Press SPEED+ or SPEED- in order to enter the time. The default value is 0:00 min:sec. The range is between 20:00 and 99:00.

+ Confirm the time with ENTER. Press SPEED+ or SPEED- in order to enter the pulse value. The default value is 72, add 1 each.

+ Confirm the target pulse with ENTER. “Ready Go” appears on the screen for three seconds and the training begins.

HRC THR (target heart rate)

Hand pulse sensors: If the user grabs the hand pulse sensor during training, the pulse symbol will light up in the heart rate window. The current heart rate is recorded and displayed within 20 seconds.

Wireless pulse receiver: For safety reasons and for the purpose of a correct display, the use of a chest strap as a pulse transmitter is recommended instead of handle sensors starting at a speed of 7.2 kmh (4.5 mph). The wireless sensor transmits the pulse directly to the system.

The normal heart rate is between 40 and 220 heartbeats per minute (BPM). If you can choose between the hand pulse sensors and the chest strap, please prefer to use the chest strap.

Heart rate training zones

30

T9.9

T9.9

Determination of the maximum heart rate: Max. heart rate = (220 - age).

Low: 0~64%

Fat burning: 65%~74%

Aerobic:

High:

75%~84%

85%

Instructions: If the user is 30 years old, the maximum heart rate is 190 in the heart rate training mode. If the user’s heart rate is at 120, this corresponds to 120/190 = 63% and

LOW is displayed.

4.4.5

User-defined programs

(1) Confirm the program selection U1-4 with ENTER. Press SPEED+ or SPEED- in order to enter the time. The default value is 00:00 min:sec; the range is between 20:00 and 99:00.

(2) Confirm the time with ENTER. Press SPEED+ or SPEED- in order to enter the distance. The default value is 0.00 km (mile). The range is between 1.00 and 99.00.

(3) Confirm the distance with ENTER. Press SPEED+ or SPEED- in order to enter the target calories. The default value is 0 calories; the range is between 10 to 9990.

(4) Hold “ENTER” for about two seconds. Now you can manually set each of the 20 sections of the training program. Set the speed with SPEED+ or SPEED- for the speed and INCLINE up or INCLINE down for the incline.

After you have completed the settings, press START to begin the training.

Note: Time, distance, calories can be entered. As soon as one of the values is entered, the other two automatically go back to zero.

USER

31

4.4.6

Body fat mode

Confirm the BODY FAT program with ENTER and the following information will be requested:

+ Age: The default value is 30. The range is between 13 and 80 years. 1-level increments, setting through SPEED+/SPEED-.

+ Height: The default value is 170 cm (66 inches). The range is between 120 and 200 cm (47 to 78 in). 1cm/1inch increments, setting through SPEED+/SPEED-. Confirm with ENTER and this will take you to the next setting.

+ Sex: The default is “male”. You can choose between female (F) and male (M) with

SPEED+/SPEED-. Confirm with ENTER and this will take you to the next setting.

+ Weight: The default value is 70 kg (150 lbs). The range is between 23 and 130 kg

(50 and 286 lbs). 1kg increments, setting through SPEED+/SPEED-. Confirm with

ENTER.

+ Please grab the pulse sensors with both hands for 15 seconds. After 15 seconds, the body fat value will appear on the screen (results - see table below).

+ After the system has displayed the values, press STOP and it will take you back to the Ready/Start mode after one minute.

Sex

M

(male)

F

(female)

BODY FAT

Under

0.0 -

4.9

0.0 -

14.9

5.0 -

9.9

15.0 -

19.9

Normal

10.0 -

14.9

20.0 -

24.9

15.0 -

19.9

25.0 -

29.9

Over

20.0 -

24.9

30.0 -

34.9

25.0 -

29.9

35.0 -

39.9

Overweight

30.0 -

34.9

40.0 -

44.9

above

35.0

above

45.0

32

T9.9

4.4.7

APP (iOS & Android) installation manual

For iOS devices (iPad)

1. APP Software Download

Connect the iPad with the APP (iTunes) store and search for PAFERS. Read through the APP manual and download the APP, which has a treadmill function, e. g., “Tread

Monitor” and “Run on Earth”. Other APPS that are not created for the treadmill cannot be connected with the computer.

T9.9

2. Find Bluetooth device and start APP

Step 1: Place the iPad in front of the LCD screen.

Step 2: Enter the iPad settings.

Step 3: Open Bluetooth and the iPad will detect all Bluetooth devices within its range.

Please search for the device name from the treadmill Bluetooth and click on the device in order to establish the connection. If several Bluetooth devices are detected and you cannot find the corresponding name, please contact your contract partner.

33

Step 4: Please wait a few seconds until the status has changed to “connected”. Then check if the Bluetooth sign appears in the upper right corner of the iPad (white sign stands for successful Bluetooth connection; gray sign stands for the Bluetooth is open, but not connected).

Step 5: As soon as Bluetooth has been successfully connected for more than 10 seconds, a white background will appear on the LCD display. The sign in the lower right corner changes from “not connected” to “connected”. This means that the computer is successfully connected with the iPad.

Step 6: Press HOME on the iPad and the screen will go to the iPad desktop. Then open the treadmill APP that you downloaded from the iTunes Store.

34

T9.9

T9.9

Step 7: Once you have gotten to the APP page, the treadmill will find the APP. As soon as the APP has successfully connected to the treadmill, the APP sign will appear on the screen. Then you can use any mode in the APP interface in order to control the treadmill.

Step 8: After any usage of the APP, press

HOME twice on the iPad. Close the APP that was just used in the background (see image).

Then go back to the iPad settings in order to close the Bluetooth function. After about 10 seconds, a beep will sound and the screen will return to the regular LCD display.

For Android devices

1.

APP Software Download

Connect the Android tablet with the Play Store and search for PAFERS. Read through the APP manual and download the APP, which has a treadmill function, e. g., “Tread

Monitor”and “Run on Earth”. Other APPS that are not created for the treadmill cannot be connected with the computer.

35

2.

Find Bluetooth device and start APP

Step 1: Please place the Android Tablet in front of the LCD screen.

Step 2: Enter the tablet setting programs and open the Bluetooth.

Step 3: Press HOME in order to get to the desktop and open the APP that you downloaded from the Play Store.

Step 4: Once you have gotten to the APP page, the treadmill will find the APP. Then a page will appear with the connection option. Press Connect and the Android Tablet will detect all Bluetooth devices in its range. Search for the Bluetooth device name from the treadmill and click on it to connect - As soon as the Bluetooth devices are detected, but you do not know the corresponding name, please contact your contract partner.

36

T9.9

Step 5: Please wait a few seconds until the status has changed to “connected”. Then check if the Bluetooth sign appears in the upper right corner of the tablet (white sign stands for successful Bluetooth connection; gray sign stands for the Bluetooth is open, but not connected).

Step 6: As soon as Bluetooth has connected successfully, the APP sign will appear on the screen. A white background will appear on the LCD display. The sign in the lower right corner changes from “not connected” to “connected”. This means that the computer is successfully connected with the tablet. Then you can use any mode in the

APP interface in order to control the treadmill.

T9.9

Step 7: After each usage, close this APP in the background. Then go back to the

Android tablet setting page in order to close the Bluetooth function. After about 10 seconds, a beep will sound and the screen will return to the regular LCD display.

NOTES

+ The APP function is based on the connection of the treadmill via Bluetooth. Make sure that the treadmill is equipped with a Bluetooth set.

+ Once the connection was successful, start the treadmill APP within two minutes.

If the APP is not started during this time or the distance between the tablet and treadmill is more than 2 m, the connection will be disrupted automatically and the steps above must be executed again.

+ The usage and function of every App are different. Please contact your contract partner or visit the PAFERS website in order to receive instructions and functional descriptions about the APP.

+ The APP does not change the metric/English unit automatically. If the unit from the APP is different from that of the console, please change the unit in the APP.

37

+ The software can be updated at any time and a new APP introduced at any time.

+ The APP contains the functions listed below. We recommend that the user opens a 3G network or Wi-Fi in order to be able to use all functions.

FITNESS MANAGEMENT: Register your personal account in the APP and log in. You can record and watch your fitness data for every training session. Some APPs require a connection to Google Maps for location services. This page can also be used as the display interface after localization.

The following circumstances may disturb or crash the APP connection:

+ If you are using the APP and at the same time have background applications running like music, images, etc. Please try to reduce switching between APPs and avoid opening too many applications. The connection can be disrupted through resource planning and independent protection of the tablet.

+ If the connection is disconnected, the treadmill will start the protection function and emit a continual warning sound. The speed will be decreased automatically in order to prevent the user from having safety problems.

If the iOS devices APP no longer works, execute the following steps in order to establish the connection again:

Step 1: Press HOME on the iPad quickly one after the other twice and delete all APPs in the temporary storage (also the PAFERS APP).

38

T9.9

Step 2: Enter the iPad setting program. Press the arrow to the right right from the

Bluetooth device name and select “Yes” in order to delete this Bluetooth device.

T9.9

Step 3: Close the Bluetooth function and turn off the treadmill.

Step 4: Turn on the treadmill again after 10 seconds.

Step 5: Enter the iPad setting program, open the Bluetooth function. Search for the

Bluetooth device name from the treadmill and connect again.

Step 6: Once you have successfully connected, please go back to the desktop and restart the PAFERS APP.

If the Android devices APP no longer works, execute the following steps in order to establish the connection again:

Search, download and install “Advanced Task Killer” in the Google Play Store. Open

“Advanced Task Killer”, select all APPs (also the PAFERS APP). Then press “Kill selected

APP”.

Enter the Android tablet setting program. Press “cancel matching”. Close the Bluetooth function and turn off the treadmill. Turn on the treadmill again after 10 seconds.

Enter the Android tablet setting program. Open the Bluetooth function. Search for the Bluetooth device name from the treadmill and connect again. Once you have successfully connected, please go back to the desktop and restart the PAFERS APP.

39

If the problem is not yet solved, please check if the connected Bluetooth device belongs to the Android Tablet. If this is the case, turn off the Android Tablet temporarily. The

Android Tablet possibly crashes or runs into other wireless interferences.

APP supporting devices (examples are listed below) Please refer to the explanations on the APP download pages for verification.

1. iOS devices

iPod touch (4th) iPod touch (3rd) iPhone 5 iPhone 4S iPhone 4

Mini iPad iPad 2 iPad

2. Android devices

ASUS Nexus 7

Samsung Galaxy Note 2

Samsung S4

The app can also be installed and used on other iOS or Android devices that are not listed here. Due to the different screen sizes and resolutions, the illustrations may be different and a calibration may be necessary if required. The models specified have already been calibrated. If an update is required, it will be specified on the PAFERS website.

Update iOS to 7.0 version or higher, Android to 4.0 or higher - this allows the user to have the best possible results.

40

T9.9

T9.9

5

WORKOUT INSTRUCTIONS

5.1

Heart rate measuring

Pulse measuring through hand sensors

The hand sensors integrated in the handles allow you to determine your heart rate.

You can measure your heart rate by lightly grasping the sensors with both hands at the same time. Blood pressure changes occur due to the heartbeat. The sensors measure the changes to the electric skin resistance caused by it. These values are then used to create an average and are displayed on the screen of the console as a heart rate.

Note:

For some people, the skin resistance change caused by the heart rate is so minimal that the measurements do not allow for usable values. Strong callus or sweat on the hands may also impair a correct measurement. In such cases, the heart rate will not be shown at all or only incorrectly.

If the measurement is incorrect or not taken at all, please check if it happens to only one person or to several people. If the pulse display only does not work in a single case, the equipment is not defective. In this case, we recommend using a chest strap to achieve a permanently correct heart rate display.

CAUTION: Your training equipment is not a medical device. Different factors may influence the accuracy of the heart rate display. The heart rate display only serves as a training aid.

Telemetric heart rate measuring

This treadmill is already equipped with a heart rate receiver as standard. Using a chest strap makes it possible for you to have a wireless heart rate measuring. This optimal and ECG-precise type of measuring reads the heart rate directly from the skin through a transmitting chest strap. The chest strap then sends the impulse to the receiver integrated in the console.

Positioning the chest strap and moistening the electrodes:

Place the belt directly below the chest, while the transmitter should be placed on the middle of the chest. The chest strap should sit comfortably, but not too loose. If the belt is too loose, the contact to the electrodes may be disrupted or the belt may slip while exercising. The transmitter turns on automatically once it is put on. In order to allow for a precise measuring, you should moisten the rubber electrodes. This is best done with a special chest strap contact gel, which is also used for ultrasound scans.

41

Note:

If you have not been active in doing sports for a longer period of time, you should first go to your physician in order to discuss your training with them. You should also contact your physician in advance in the event of heart problems, high/low blood pressure and obesity.

Training with heart rate orientation

Heart rate orientation guarantees an extremely effective and healthy training. Through your age and the following table, you can quickly and easily read and determine the optimal pulse for your training. An alarm will sound if your heart rate exceeds the set target heart rate. Which target heart rate is important for which training goal can be found out in the following.

Fat burning (weight management): The main goal here is to burn deposits of fat. In order to achieve this training goal, a low training intensity (approximately 55% of the maximum heart rate) and a longer training period are required.

Cardiovascular training (cardio training): The primary goal is to increase stamina and fitness through an improved provision of oxygen through the cardiovascular system. In order to achieve this training goal, medium intensity (approximately 75% of the maximum heart rate) with a medium training period is required.

Anaerobic (maximum) load training: The main goal of maximum load training is to improve recovery after short, intense loads in order to be able to quickly return to the aerobic zone. In order to achieve this training goal, a high intensity (approximately

90% of the maximum heart rate) with short, intense load is required, which is followed by a recovery phase in order to prevent muscle fatigue.

42

T9.9

T9.9

220

200

180

160

140

120

100

80

Example:

For a 45-year-old man or woman, the maximum heart rate is 175 (220 - 45 = 175).

• The fat burning target zone (55%) is at approximately 96 beats/min.

= (220 - age) x 0.55.

• The cardio target zone (75%) is at approximately 131 beats/min.

= (220 - age) x 0.75.

• The maximum heart rate for an anaerobic load training (90%) is at approximately

157 beats/min. = (220 - age) x 0.9.

200

180

150

110

20

Heart rate diagram for training intensity

195

175

146

107

190

171

143

105

185

166

139

102

180

162

135

99

175

157

131

96

170

153

128

94

165

148

124

91

160

144

120

155

139

116

150

136

113

88

85

83

70 25 30 35 40 45 50 55 60

Age

Maximum pulse (220-age)

90% of maximum pulse - anaerobic (maximum) intensity training

75% of maximum pulse - cardiovascular training (cardio training)

55% of maximum pulse - fat burning (weight control)

65

43

5.2

10 tips for effective running training

1. Set goals

What would you like to achieve with your training? Weight regulation, improved stamina, prevent risk of disease, more mobility, cardiovascular training, etc. In order to achieve your long-term training goal, set individual partial goals, e. g., weekly or monthly goals.

2. Concentration on training

Try to only dedicate yourself to your training session and do not be distracted.

3. Position yourself correctly while exercising

When you execute the movement, you should start with a moderate speed and hold on if needed. The speed can then be increased gradually. The adjustment of your natural running style will occur relatively quickly. Beginners and overweight people should start with a walking program in order to not overload their joints in the beginning.

4. Correct breathing / appropriate resistance level

Do not overexert yourself physically and mentally by starting with resistance levels that are too high. Start slowly and increase the resistance steadily. Aim for regular and calm breathing.

5. Keep yourself properly hydrated

Drink, drink, drink! Have a drinking bottle close by during your workout.

6. Sufficient recovery periods

Allow your body and your muscles enough time to recover after your workout. Only a relaxed muscle will be fully operational again.

7. Choose a diversified program

Different program functions from your training console support you in doing this. For example, you can complete an interval, incline or step number training unit.

8. Creating the right workout

Every training session should have a warm-up phase, a cool-down phase and a targeted stretching. It increases physical and mental performance and prevents injuries and sore muscles.

44

T9.9

T9.9

9. Workout journal

Keep a record of your training sessions. Note the date, resting pulse, active pulse, recovery pulse, resistance level, time, distance, calories burnt and fitness level.

10. Reward yourself

Do something good for you and your body after training or after achieving a partial goal. Go to the sauna or a swimming pool. Mix a protein shake or enjoy a delicious salad.

5.3

Designing a workout

We recommend two or three workouts per week. Warm up for about five minutes before starting each workout. Finish the workout with a cool-down and targeted stretching.

Warm-up approx. 5 min. Dynamic movement of large muscle groups at a low intensity. Core body temperature increases and the metabolic process is speeded up.

Beginner

Days Duration Intensity

Mon 20 min.

Brisk walking

Wed 20 min.

Brisk walking

Fri 20 min.

Brisk walking

Increased speed for two to three minutes in between in the second week.

Maintain your heart rate.

WEEK 1 + 2

Advanced

Duration Intensity

30 min.

Running at a slow speed

30 min.

Running at a slow speed

30 min.

Running at a slow speed

Increase the speed in between in the second week. Maintain your heart rate.

Beginner

Days Duration Intensity

Mon 25 min.

After every 10 min. run for 1 min.

Wed 25 min.

After every 10 min. run for 1 min.

WEEK 3 + 4

Advanced

Duration Intensity

35 min.

35 min.

Running at a moderate speed

Running at a moderate speed

45

Fri 25 min.

After every 10 min. run for 1 min.

In the fourth week, run for two minutes after every 10 minutes. Maintain your heart rate.

35 min.

Running at a moderate speed

In the fourth week, increase the speed for one minute each. Maintain your heart rate.

Beginner

Days Duration Intensity

WEEK 5 + 6

Advanced

Duration Intensity

Mon 30 min.

Alternate walking and running

Wed 30 min.

Alternate walking and running

Fri 30 min.

Alternate walking and running

In the fifth week, run for three minutes after every eight minutes. In the sixth week, run for three minutes after every six minutes.

Maintain your heart rate.

40 min.

40 min.

40 min.

Running according to heart rate

Running according to heart rate

Running according to heart rate

Pay attention to your heart rate.

WEEK 7 + 8

Beginner

Days Duration Intensity

Mon 35 min.

Walk 8 minutes, run 5 minutes

Wed 35 min.

Walk 8 minutes, run 5 minutes

Advanced

Duration Intensity

45 min.

45 min.

Running according to heart rate

Running according to heart rate

Fri 35 min.

Walk 8 minutes, run 5 minutes

Increase in the eight week: Walk five minutes, run seven minutes. Maintain your heart rate.

45 min.

Running according to heart rate

If you feel comfortable, then include a few steps or hills in your training.

Cool-down approximately 5 min.

46

Finish your training at low resistance and at slow speed. Allow your body to gently slow back down.

T9.9

5.4

Stretching exercises for leg & chest muscles

T9.9

1. Exercise: Stretching of front thigh / leg extension (quadriceps)

• Stable position, grab arches of feet

• Pull heel towards buttocks, knee points downwards

(no abduction)

• Straight upper body, avoid tilting the pelvic forward

(hollow back) by tensing the abdominal muscles

• Change legs

2. Exercise: Stretching the back thigh / leg curl (hamstring)

• Pull thigh towards upper body with both

hands

• Stretch through increased stretching in

the knee joint

• The lower leg maintains contact with the

floor, keep hips bent

• Change legs

47

3. Exercise: Stretching the calf muscles (gastrocnemius)

• Place feet parallel to each other pointing forward,

the heels touch the floor

• Support yourself on a chair coming from a lunge

• Move your body weight to the front leg, press

your heel from the rear leg towards the floor and

hold the contact

• Slowly stretch your knee of the rear leg until you

feel the stretch in your calves

• Change legs

4. Exercise: Stretching the chest muscles (pectoralis major)

• Stand parallel to a wall

• Place your forearm at 90° to the wall with the elbow

just above shoulder height

• Turn your head and upper body gradually to the

opposite sides until you feel a stretch in the front

chest, of the shoulder being leaned on

• Pay attention to tension in your abdominal and

gluteal muscles

• Your weight is on your front leg

• Change legs

All recommendations of these instructions apply solely to healthy persons and are not suitable for those with heart or cardiovascular problems. All of the tips are intended only as a guide to help you create a workout. Your physician can offer appropriate advice for particular, personal requirements.

We hope you enjoy your workout and have a lot of success!

48

T9.9

5.5

Workout journal

T9.9

Date

Distance

Time (min.)

Training weight

Resistance level Ø Pulse

Calories burnt

I feel ...

Body weight

49

6

WARRANTY INFORMATION

Taurus training fitness equipment is subject to strict quality controls. However, if a fitness equipment purchased from us does not work perfectly, we take it very seriously and ask you to contact our customer service as indicated. We are happy to help you by phone via our service hotline.

Error descriptions

Your fitness equipment is developed for long-term, high-quality training. However, should a problem arise, please first read the operating instructions. For further assistance, please contact your contract partner or call our service hotline. To ensure your problem is solved as quickly as possible, please describe the defect as exactly as possible.

In addition to the statutory warranty, we provide a warranty for every fitness equipment purchased from us according to the following provisions.

Your statutory rights are not affected.

Warrantee

The warrantee is the first/original buyer and/or any person who received a newly purchased product as a gift from the original buyer.

Warranty periods

The following warranty periods begin on delivery of the fitness equipment.

Model

T9.9

Use

Home use

Full warranty

24 months

Semi-professional use 12 months

Frame

30 years

Motor

10 years

Repair costs

According to our choice, there will either be a repair, a replacement of individual damaged parts or a complete replacement. Spare parts, that have to be mounted while assembling the equipment, have to be replaced by the warrantee personally and are not a part of repair. After the expiration of the warranty period for repair costs, a pure parts warranty applies, which does not include the repair, installation and delivery costs.

50

T9.9

T9.9

The terms of use are defined as follows:

• Home use: solely for private use in private households up to 3 hours per day

• Semi-professional use: up to 6 hours per day (e. g. rehabilitation centers, hotels,

clubs, company gyms)

• Professional use: more than 6 hours per day (e. g. commercial gyms)

Warranty service

Within the warranty period, equipment which develops faults as a result of material or manufacturing defects, will be repaired or replaced at our discretion. Ownership of equipment or parts of equipment which have been replaced is transferred to us.

The warranty period is not extended nor does a new warranty period begin following repair or replacement under the warranty.

Warranty conditions

For the warranty to be valid, the following steps must be taken:

Please contact our customer service by email or phone. If the product under warranty has to be sent in for repair, the seller bears costs. After expiry of the warranty, the buyer bears the costs of transport and insurance. If the fault is covered by our warranty, you will receive a new or repaired equipment in return.

Warranty claims are invalid in case of damage resulting from:

• misuse or improper handling

• environmental influences (moisture, heat, electrical surge, dust, etc.)

• failure to follow the current safety measures for the equipment

• failure to follow the operating instructions

• use of force (e. g. hitting, kicking, falling)

• interventions which were not carried out by one of our authorized service centers

• unauthorized repair attempts

Proof of purchase and serial number

Please make sure that you are able to provide the appropriate receipt when claiming on your warranty. So that we can clearly identify the model of your equipment, and for the purposes of our quality control, you will need to give the serial number of your equipment, when contacting the service team. Where possible please have your serial number and your customer number ready when you call our service hotline. It will help us to deal with your request swiftly.

51

If you have trouble finding the serial number on your fitness equipment, our service team is at your disposal to offer further information.

Service outside the warranty period

We are also happy to issue an individual cost estimate if there is a problem with your fitness equipment after the warranty has expired, or in cases which do not fall under the terms of the warranty, e. g. normal wear and tear. Please contact our customer service team to find a quick and cost-effective solution to your problem. In such a case you will be responsible for the delivery costs.

Communication

Many problems can be solved just by speaking to us as your contract partner. We know how important it is to you as a user of the fitness equipment to have problems solved quickly and simply, so you can enjoy working out with minimal interruption.

For that reason, we also want to resolve your queries quickly and in a straightforward manner. Thus, please always keep your customer number and the serial number of the faulty equipment handy.

7

DISPOSAL

At the end of its operational life, this equipment cannot be disposed of in normal household waste. Instead, it must be disposed of via an electricals recycling centre. Further information can be obtained from your local authority‘s recycling service.

The materials can be recycled as per their symbols. Through the reuse, recycling of materials or other forms of recovery of old equipment, you make an important contribution to the protection of the environment.

52

T9.9

T9.9

8

ORDERING ACCESSORIES

Sport-Tiedje floor mat size XXL

Art. No. ST-FM-XXL

Polar transmitter chest strap T34 uncoded

Art. No. T34

Togu Senso Walking Trainer

Art. No. TOGU-470501

Chest strap contact gel

250ml

Art. No. BK-250

Sport-Tiedje silicone spray

Art. No. ST-1003

Fitness equipment care set

Art. No. HF-500

53

9

ORDERING SPARE PARTS

9.1

Service hotline

So that we can give you the best possible service, please have your model name, part

number, serial number, exploded drawing and parts list ready.

SERVICE-HOTLINE

DE

+49 4621 4210-0

+49 4621 4210-699 [email protected]

Mon - Fri 8:00 am - 6:00 pm

Sat 9:00 am - 6:00 pm

NL

+31 172 619961 [email protected]

Mon - Thu 9 am - 5 pm

Fri 9 am - 9 pm

Sat 10 am - 5 pm

UK

+44 141 876 3972 [email protected]

Mon - Fri 9 am - 5 pm

9.2

Serial number and model name

Before assembling your equipment, find the serial number on the white sticker and enter it in the appropriate space.

Serial number:

Brand / category:

Taurus treadmill

Model name:

T9.9

54

T9.9

T9.9

9.3

Parts list

Qty.

Part number

1 HTF236P-D5

1 P-3534

4

1

1

1

1

2

2

2

1

4

1

1

1

1

2

2

1

10 SOC8

1 P-3544

SAA5-15

SOI5

XEK-248

XRA-179-003

XEM-016

1XEK-247

P-3535

P-3540L

P-3541L

A1A094E0505-001

SOF8A

P-3540R

RCA-004

P-3541R

NO-4994

P-3542

P-3543

1

1

4 NS-266

XL-1293B

2

1

1

XEK-249

RBA-043

RBA-042

24 SAK3-8

4 SAI3-8

30 SCI4-16

XL-874A

XL-1084A

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

No

1

2

5

6

7

3

4

8

9

10

12

13

14

Description

console set console upper cover nylon nut M8xP1.25 iPad holder round head Philips screw M5xP0.8x15

nut M5X25X13

Bluetooth module console board (LCD with BT module) safety key switch set keyboard console lower cover handrail upper cover left handrail lower cover left handrail tube hex nut M8XP1.25

handrail upper cover right console overlay decal handrail lower cover right hand pulse sensor plate hand pulse plastic base rocking bar switch cover compressed spring handrail switch with hand pulse wire-lower handrial keyboard handrail sticker-incline handrail sticker-speed round head Philips self-tapping screw ø3x8 round head Philips self-tapping screw ø3x8 truss head Philips self-tapping screw ø4x16 control wire-upper hand pulse wire-upper

55

No

31

57

58

59

59A

60

61

62

63

64

65

66

67

54

55

56

50

51

52

39

40

41

36

37

38

32

33

34

35

42

44

45

46

Qty.

Part number

1 XHB-TW-400

6

1

1

1

2

1

4

4

9

2

1

8

1

1

1

1

1

2

4

2

1

1

XL-1292

XL-1293A

XL-1291

XL-1286B

SDA8-20I

XEK-028-26

JTFA048

SCE5-10

RAH-SP-002

P-3536R

P-3536L

XEK-250

BAC0250-150-03

SAE5-8

4

1

1

1

1

1

8

JTCA064

JTCB058

SK-298A

1 P-2588

15 SCE5-15

2 BAA1000-120-50

XM-121

SK-439

SOC10

SOC10-8T

XM-118

SGA10-25I

SPA100-200-30

SPB10

CA-240J10

SGA8-80I

SOA8

PEC-UC-1

56

Description

wireless heart rate receiver keyboard connected wire handrail switch with hand pulse wire-upper

BT module connected wire control wire-lower

Truss hex screw M8xP1.25x20

hand pulse board console bracket

Truss head Philips screw M5xP0.8x10

handrail side sticker bottle holder-right bottle holder-left

USB charging board double-sided tape 25mmx15mmx0.3t

round head Philips screw M5xP0.8x8

upright tube left upright tube right truss hex screw motor cover upper truss head Philips screw M5xP0.8x15

foam sticker 100mmx12mmx5t incline motor

CKS hex screw M10xP1.5x40

nylon nut M10xP1.5 nylon nut M10xP1.5x8t

DC motor

CKS hex screw M10xP1.5x25

flat washer ø10xø20x3t spring washer M10 drive belt

CKS hex screw M8xP1.25x80

hex nut M8xP1.25

wire clip knob

T9.9

T9.9

84

85

86

87

88

89

90

92

93

94

95

96

97

98A

99

No

68

69

79

80

81

76

77

78

82A

83

71

72

73

74

75

1

1

2

2

8

1

1

1

1

1

Qty.

Part number

6

2

SAA5-10GZ

BAE0500-240-3

Description

round head Philips screw M5xP0.8x10

rubber pad 50mmX24mmX3t

1

6

4

4

1

1

6

1

1

1

1

1

1

1

1

1

XEH-002-001

XEA-A002A

XLZ-TM

P-1825

XRB-013-002

XEG-10-001

NT-1636

XEM-002

SCE4-10

P-2231

NO-2399

P-1301F

MB-011 power cord socket power switch power cord power cord switch cover controller circuit breaker power cord collector sensor truss head Philips screw M4xP0.7x10

sensor fixing base sensor fixing plate fixing cushion running deck to replace running deck, the part number (184)x2pcs & (185)x3pcs must be replaced together

1 SCI4-12 truss head Philips self-tapping screw ø4x12

BJ-22-080B

SIA8-35I

SIA8-40I cable tie 2.2mmx80mm

counter sink hex screw M8xP1.25x35

counter sink hex screw M8xP1.25x40

2 NAL286E1367 aluminum pedal to replace aluminum deck, the part number (89) must be replaced together

BAA13480-200-15 foam sticker 1348mmx20mmx1.5t

NO-3805 aluminum pedal fixing plate

P-3550L

P-3550R

SAM4-20 rear end cap left rear end cap right round head Philips self-tapping screw ψ4x20

CB00050C

NRL-005

SGA10-100I

SPA100-200-10

SPD10 running belt front roller

CKS hex screw M10xP1.5x100

flat washer ø10xø20x1.0t

thread washer M10

57

No

100

121

122

126

128

129

130

135

138

140

143

144

145

115

116

117

118

119

120

105

106

107

108

109

110

101

102

103

104

111

112

113

114

Qty.

Part number

1 SOA10

2

2

1

2

2

2

1

2

1

2

4

1

2

4

5

2

2

1

1

1

2

2

4

2

1

1

8

2

2

1

BJ-36-163B

BE-1500

SSB8-200

BD-001-100

SSH5-70-70M

SEA8-115-25

8 SPA080-200-20

12 SPB8

XLT044

NRL-005A

SGA10-80I

NO-4059

SPB5

SAE5-12

P-1032

SCE6-10

JTBC010

NT-1000

SGA8-25I

P-1037

PB-00-003

SGC10-60-30I

NT-1379

SQC100-20

P-1155

SPA060-160-10

SMM4-16

JTAA040B

XLT002

XLT001

XLT047

PEC-HC-25

58

Description

hex nut M10xP1.5

extension wire-yellow 14AWGx450x2R rear roller

CKS hex screw M10xP1.5x80

dustproof iron plate spring washer M5 round head Philips screw M5xP0.8x12

rubber pad truss head Philips screw M6xP1.0x10 incline base assembly incline base fixing base

CKS hex screw M8xP1.25x25

plastic sleeve wheel ø60xø10x30

CKS hex screw M10xP1.5x60

incline base flex ㄇ-shaped iron plate pin

R-pin foot pad washer ø6xø16x1t washer Philips self-tapping screw ø4x16 frame assmebly extension wire-white 14AWGx90x2T extension wire-black 14AWGx90x2t extension wire-yellow 14AWGx500x2R

KSS wire clip fixing base cable tie 3.6mmx163mm

magic strap

T-wrench silicon

L hex spanner & Philips screwdriver 5mmx70mmx70mm hex screw M8xP1.25x115

washer ø8ø20x2t spring washer M8

T9.9

T9.9

180

184

185

186

188

222

223

No

146

167

168

169

173

174

175

177

179

147

149

157

159

Qty.

Part number

1 P-2589L

1

1

1

1

2

3

1

4

1

1

1

1

2

4

2

1

1

1

1

1

1

1

1

P-2589R

XLT035

XEN-008

XEB-009

BAC9100-920-05

BAC0900-200-05

P-2296B

XLT074

XLT027

XLT029

XLT033

XLT050

P-2214

DEC-20-1100

PM-001

RBA-016

RBA-014

XHA-T34

PK-L-027

XEK-245

NO-4060

PEC-CS-0610

XL-1285

Description

motor side cover left motor side cover right extension wire-white 14AWGx550x2T choke filter double-sided tape 910mmx92mmx0.5t

double-sided tape 90mmx20mmx0.5t

side pedal decorative strap extension wire-yellow 14AWGx300x1T1R extension wire-white 14AWGx260x2t extension wire-black 14AWGx260x2t extension wire-white 14AWGx300x2t extension wire-black 14AWGx300x2t safety key nylon rope clip grounding sticker 20x1390L grounding sticker 20x670L

Polar heart rate transmitter water bottle

ErP board connecting board base

PC board insulate post

ErP board connecting wire

59

9.4

Exploded drawing

60

T9.9

T9.9

CONTACT

Company head office

Sport-Tiedje GmbH

Flensburger Str. 55

24837 Schleswig

Germany

GENERAL INFORMATION:

DE +49 4621 4210-0 [email protected]

NL +31 172 619961 [email protected]

UK +44 141 876 3972 [email protected]

Hotline for Technical Information

DE +49 4621 4210-0

+49 4621 4210-699 [email protected]

NL +31 172 619961 [email protected]

UK +44 141 876 3986 [email protected]

www.sport-tiedje.com

www.taurus-fitness.de

DISCLAIMER

©2011 TAURUS is a registered brand of the company Sport-Tiedje

GmbH. All rights reserved. Any use of this trademark without the

explicit written permission of Sport-Tiedje is prohibited.

Product and instructions are subject to change. Technical data can be changed without advance notice.

Please find a detailed overview including address and opening hours for all specialist fitness stores of the Sport-Tiedje Group in Germany and abroad on the following

website.

www.sport-tiedje.com/en/stores

61

Notes:

62

T9.9

T9.9

63

Treadmill

T9.9