USER MANUAL
Model: YPH-12H -S1
PORTABLE AIR-CONDITIONER
Thank you for selecting super quality air conditioner. Please be sure to
read this manual carefully before using it. Any question, please
contact the professional for help.
CONTENTS
CONTENTS……………………………………………………………1
IMPORTANT SAFEGUARD…………………………………………2
FEATURES AND PARTS LIST………………………………………3
CONTROL PANEL……………………………………………………4
REMOTE CONTROL…………………………………………………6
OPERATION METHODS……………………………………………..8
INSTALLATION……………………………………………………….10
WATER & DRAINAGE METHODS…………………………….…..13
MAINTENANCE………………………………………………………14
TROUBLE SHOOTING………………………………………………15
INSTALLATION ACCESSORIES…………………………………...16
APPENDIX……………………………………………………………..17
--1--
IMPORTANT SAFEGUARDS
Read all instructions for the safety of yourself and your family.
*Keep the unit on a flat and dry place. Leave at least 50cm space
all around the unit.
*Installation suits to national electrical net layout rules.
*After installation, please check if the plug is perfect and firmly
insert in the jack.
*Keep the air inlet and outlet ventilation open.
*Keep the appliance far from gas or other inflammable liquids.
*Place the electrical wire in order and avoid being blundered and
plugs pulled out.
*Correctly use the power cord. If destroyed, please close the air
conditioner and pulled out of the plug. Please ask a specialist for
help.
Please do not
*No not use the appliance other than domestic purpose.
*Do not install in the washing room.
*Do not let children play by himself or herself. Children and
deformity suffer cannot use the conditioner without guardian.
*Never use the main plug as a switch to start and stop the air
conditioning unit. Use the provided ON/OFF switch located on the
control panel.
*Do not let your skin or eyes enjoy the cooling wind directly.
*Do not put anything on the unit.
*Do not put anything on the air-inlet and air-outlet.
*Do not use insects-killing spray and other flammability near the
conditioner
*Do not scratch the surface by aculeate things.
*Do not spray oil or water into the conditioner.
*Do not place it where have water or other liquid.
*Do not clean the conditioner by water, use waterish cloth to wipe.
*Do not use chemist solvent to clean the conditioner, such as
benzene, oil and alcohol. Use neutral cleanser to wipe
conditioner.
Suggestion:
Stop the conditioner if the temperature is higher than 40℃ under
cooling or lower than 7℃ under heating.
--2--
FEATURE AND PARTS LIST
Feature
*No installation is required.
*Easily moved . The handle makes moving more convenient.
*Totally luxury panel and modern appearance design.
*LCD Blue screen display.
*Water-cooled mode and adding water mode is most energy
saving and environmental protecting.
*Low noise and strong wind.
*Auto swing makes wind blow from left to right automatically.
*Three-minute restart delay to protect compressor.
Parts list:
1. Control panel
1
4
2
2. Horizontal louver
5
3
3. Vertical louver
7
4. Handle
5. Air-inlet grille
6. Castor
6
7. Exhaust pipe
Fig 1
8. Water injection port
8
9. Power cord pothook
10. Air filter
9
10
11. Air-outlet grille
12. Connector of Outer water tank
11
12
13. Inner water tank
14
13
14. power cord and plug
Fig 2
--3--
CONTROL PANEL
CAUTIONS: If the unit is turned off in cool mode and started
immediately, it will wait at least 3 minutes before running.
图3
1. Buttons
ON/OFF:Press this button to turn on/off the unit.
Mode: Press this button to select mode.
Up/down: Press up or down button to set temperature or adjust
time in Timer mode. Press both buttons to exchange Celsius to
Fahrenheit or vice versa.
Swing: press this button to make the vertical louver swing
automatically. Press it again, the swing will stop.
Speed: Press this button to select high, middle or low fan
speed.
Timer indicator.
Econ: press this button to have an energy saving mode. This
default temperature is 27℃ in cooling mode, and 23℃ in
heating mode, also fan speed is low. These data can’t be
changed. The LED display will flash
accordingly. Press
is flashing. After it’s cancelled you
again to cancel it when
may set temperature or choose fan speed.
--4--
2.LCD display
:Cool mode indicator.
:Dehumidifying mode indicator
: Fan mode indicator, also it
inner-dehumidifying mode is chosen.
will
flash
when
:Heating mode indicator
:Water Full indicator.
:Set temperature under cooling mode or room temperature
under fan mode. TEMP means temperature, ℃ means
centigrade, and ℉ means Fahrenheit.
When 88 is E2, it means room temperature sensor faulty;
When 88 is E3, evaporator sensor faulty; When 88 is df, the
cooling system is defrosting or anti-foresting..
:Water Injection indicator.
:Auto-on or auto-off indicator. On means auto-on, off means
auto-off.
:Fan speed can be low, middle and high. You can choose
swing or not.
:Energy saving status (only in heating and cooling mode).
--5--
REMOTE CONTROL
1.Button instruction
Up/Down
Mode
When unit is on or
under Timer Mode,
press this key to choose
cooling,
heating,
dehumidifying or fan
Press temperature will
increase 1℃or1℉ ,
temperature
press
will decrease 1℃or 1℉。
Or adjust time under
timer Mode
Fan
Press this to choose fan
speed (low, middle or
high). When the unit is
turned on at first time,
the default speed is low
Power Button
Press this button to
turn on/off the unit.
Swing Button
Press this button to
control swing function.
Temperature Button
Press this button to
choose ℃ Centigrade
or ℉ Fahrenheit
Econ Button
Under cooling model,
press this button to get
energy saving mode, Low
wind, and low noise.
Timer
Press this to set auto on
time when the unit is
off, to set auto off time
when the unit is on.
Press
to set the auto
on/off time you want.
Room temperature display
Press this to display the
room temperature, press it
again to cancel room
temperature display; it can
be used as a thermometer
when the unit is off
--6--
2. Symbol instruction:
(1).Mode
From up to down, it is cooling, heating,
dehumidifying and fan mode, press
Mode key to set. The default is Fan,
when the unit is on first time.
(2). Signal
It flashes when signal’s sent out.
(3).Economic
It appears when it is under economic
mode, and disappears when the
mode’s cancelled.
(4).Swing
It appears when the Swing is on, and
disappears when Swing is off. The
default is on.
(5). Fan
It is available when the unit is cooling or
fan Mode, you can set fan speed as
you need.
(6). Room temperature and set
temperature
When the unit is off, it displays room temperature and the word
“Room” will show on the screen; when it is under cooling mode, you
can set temperature by pressing
, and then the “Set” will be on.
It will display room or setting temperature by pressing . The
temperature range is 18-30 ℃,default is ℃。
(7). Timer
It displays when timer is on, to show the auto on/off time
3. Technology specification
(1) Remote control: DC3V Voltage 2.4~3.3V
(2) Time: 24hs, Tolerance≤5min
--7--
(3) Temperature tolerance:±1℃or ±1℉;
(4)Temperature range:18-30℃/64-86℉。
OPERATION METHODS
Timer set
1. Set timer-off
Press the Timer button when the unit is on. The screen will flash “-“ five times. During this period, press Up or Down button to adjust
set time (range: 0.5h to 24h). After time is set, if press
once in
the first 3 hours, the set time only increases or decreases 0.5h, if
after 3 hours, the set time will increase or decrease 1h. The set
time will flash 5 times after adjusting. Once the set time is up, the
unit will turn off automatically.
2. Set timer-on
Press the Timer button when the unit is off. Same as timer-off set.
After time is set, you may choose working mode, if choose cooling
or heating mode, you can set temperature; if choose
dehumidifying mode, you can set targeting humidity. Once the set
time is up, the unit will turn on automatically.
3. Change the set time
When Timer is on, if want to change set time, please press Timer
button, now the screen will flash remaining time, during this time
press Up or Down button to adjust time. The set time can also be
cancelled if you press the Timer button once again during the
flashing time
Mode operation
1. Cooling and Heating Mode
*Press Mode button to choose Cooling or Heating, now the screen
will show
*Press
to set a proper room temperature.
*The range is 18~30℃(64-86°F). The temperature will increase
--8--
or decrease 1℃ or 1°F by pressing
.
*Press Speed button to choose a proper fan speed.
* Press Econ in the cooling and heating mode, the set
temperature is “27℃/ 80℉” under cooling mode, “23℃/ 73℉”
under heating mode, and fan speed is low. If want to change
temperature or speed, please Econ again to cancel..
*Press Swing button to adjust the direction of vertical louver.
*Adjust horizontal louver manually.
2. Dehumidifying Mode
*Press Mode to choose dehumidifying when the unit is on or
under auto-on, now the screen will show
*Setting temperature and choosing fan speed is unavailable under
this mode.
*Adjust horizontal louver manually.
3. Fan mode
*Press MODE button (or Fan button) to choose Fan mode, the
LCD will display .
*Select the fan speed by pressing SPEED button on the remote.
Under this mode, if press SPEED button for 5 seconds,
inner-dehumidifying mode will be activated, which means both
upper fan and lower fan will work. To cancel it press SPEED button
again for 5 seconds.
*The temperature cannot be set under fan mode.
*Press Swing button to make vertical louver swing or stop.
*Adjust horizontal louver manually.
NOTE:
1. Under cooling mode, when the screen shows
, please
add water from the top, which will improve cooling
efficiency, at the same time lowering the noise.
2. The unit will stop working when water level exceeds the
high level, please drain water with drainpipe. The unit will
start working when water is drained.
3. No need to use air exhaust duct when in Fan and
dehumidifying mode.
4. If your room is directly exposed to the sun, draw the
curtains please.
--9--
INSTALLATION
1. Selection of Installation Place
Please install the unit where is flat and dry. Leave at least 50cm
space all around the Unit (when the hose is not connected). (Fig.5)
2. Air Exhaust Duct Mounting Method
1) Fix the square end of the exhaust dust to the exhaust terminal
of the unit. (Fig.6)
2) Put the other end (discharge) to the nearest window. Leave at
least 50cm place around it.
50
50
50
Fig 5
Fig 6
NOTE:
The length of the air exhaust duct is about 170cm when it’s
extended (adapters included) and 60cm when not. We suggest use
the minimum length, which will save energy for you.
This length has been designed especially according to the
specifications of the air conditioner .Do not use an extension
or exchange of a different hose as that may lead to
malfunction.
3. Window Kit Installation
- - 10 - -
The window kit is designed to fit most standard vertical and
horizontal windows. However, it may be necessary for you to
modify in some aspects of the installation procedures for certain
Vertical
Window
Horizontal
Window
Window Kit Size:
Min Size:90cm
Max Size:130cm
Window Kit Size:
Min Size:90cm
Max Size:130cm
Fig 8
Fig 7
types of windows. Please refer to the illustrations. (Fig.7 and Fig.8)
4. Mounting illustrations
1)
Mounting in the wall
130cm
40cm
Fig 9
- - 11 - -
2) Correct bending
θ≤45°
Fig 10
θ≤45°
Fig 11
3) Wrong bending
Fig 12
- - 12 - -
Adding and Draining Water
Adding water
*The condensing water is recycled to improve efficiency through
cooling condenser. Also it will lower the noise and save energy.
*When the condensing water is not enough for pumping, the water
Injection indicator on the control panel will illuminate, you’d better
inject some water into the water draw, right of the handle, there is
a cover. Meanwhile, pay attention the water level pole at your
right, where show the water quantity.
Note: The water-cool-mode is not working under
dehumidifying, fan or heating mode. Do not add water.
Clean Water
Water Level
Small Cover
Water Draw
Cover
Drainage
Drainage Port
Plug
Lid
Fig 13
*When the water is full, the water full indicator will light and the
compressor will stop working. The buzzer will buzz 10 times every
5 minutes until the water is below the high level or drained by hand.
When the alarm stops the unit will work automatically.
*Before you drain the water you need to turn the unit off and pull
the plug out of the power supply. Upcap the lid, remove the rubber
plug on the drainage port, then let the water flow out. Once drained,
put the rubber plug back and screw the lid up an switch it on.
(Fig.14). If the provided pipe is not long enough, you may buy a
longer one (inner diameters 9mn).
Note
Move the unit gently when the water is high. If not, the water may
spill all inside of the unit.
- - 13 - -
MAINTENANCE
Cleaning
Turn off the unit and pull the plug out of the socket before cleaning.
1. Clean the surface
Clean the surface of the unit with a duster or a half-wet soft cloth.
Do not use chemical solvent like benzene, alcohol, gasoline, etc.,
otherwise the surface may be damaged or even deformed.
2. Clean the air filter
If the air filter is blocked with a lot of dust,
the efficiency will be reduced. You’d better
Clean the filter every two weeks.
1) Pull out the air filter as Fig.15.
2) Wash the air filter by immersing it
gently into warm(under 40°C or 104°F)
water with neutral detergent. Rinse the
filter and dry it in a shaded place.
2) Push the air filter back into the original
position.
Fig 15
End of season
1. Pull the plug out of the drain mouth and remove the water from
the water plate and inner water tank. You can remove the water
entirely by slanting the unit back.
Setting the fan mode, then press the Fan button for 5 seconds until
the lower fan works. After that, operate the unit in fan mode for 2 to
3 hours until the pipe is dry. In this way the inside of the unit can be
dried and the mildew growth can be suppressed.
2. Switch off the unit and disconnect the plug from the power
supply.
3. Tie the cable with sting.
4. Remove the air exhaust duct and keep it carefully.
5. Wrap the unit with the plastic bag, and keep it in a dry place.
6. Take the batteries out of the remote control and keep them well.
- - 14 - -
TROUBLE SHOOTING
Before contacting the professional, please first check
it yourself referring to the followings.
Trouble
Check
Solution
Is power fail?
Is plug out?
The unit doesn’t Is power fuse or switch off?
operate at all.
Is the set time suitable?
Is water full alarm on?
It is normal.
Insert the plug into the
socket steadily.
Change the fuse or switch
on.
Change the set time.
Pour the water.
Is air inlet or outlet blocked?
Clear off the blocks.
Is there any other heat source in Move the heat source.
Cooling/Heating
room?
efficiency is not Are air filters very dirty?
Clean the air filter.
good.
Is the temperature suitable?
Change temperature.
Is fan speed set at low?
Select suitable fan
speed.
It is the inner refrigerant flowing It is normal.
inside.
Is it inclined?
Place it in a flat place.
Noisy
Vibration
Stop running and pull the plug out in case
something enumerated below happens. Then
contact the professional for help.
·The fuse and switch often break.
·The power cord superheat or sleeve of the cord is broken.
·There is abnormal odor or smoke comes out of the unit.
Self-diagnosis function
code
E2
E3
Indication
Room temperature faults
Faulty coil temperature
Check
Room temperature sensor faulty
Coil temperature faulty
Note: When display “df”, it means that the coil is defrosting. That is
the normal status.
- - 15 - -
INSTALLATION
ACCESSORIES
Flexible exhaust hose with adapters…………………………….1/set
Stretch from 28cm up to 150cm
Square connector…………………………………………………..1 pc
Flat and round connector…………………..………………………1 pc
Adjustable window slider kit….…………………………………….1/set
Stretch from 90cm 130cm
Screw (the length is 10mm)…………………………………………...1 pc
Plug (square)………………………………………………………....1 pc
Fig16
- - 16 - -
APPENDIX
Fuse Parameter
Type: FSD
Voltage: 250V
Current: 3.15A
Disposal: Do not dispose this product as unsorted municipal
waste. Collection of such waste separately for special treatment is
necessary.
- - 17 - -