Craftsman 315 Owner`s manual

Owner's Manual/Manual
Del Propietario
1/2 HP
315_N=
GARAGE DOOR OPENER
ABRIDOR DE PUERTA DE COCHERA
For Residential
315_.=
Use Only
Model • 139.53930D
m
Z
t.n
rrl
t.n
z_
o
Read and follow all safety rules
and operating instructions before
first use of this product.
Leer y seguir todas las reglas de
seguridad y las instrucciones de
operacion antes de usar este
producto por primera vez.
Fasten the manual near the garage
door after installation.
Guardar este manual cerca de la
puerta de la cochera.
Periodic checks of the opener are
required to ensure safe operation.
Se deben realizar revisiones
periodicas del abridor de puertas
para asegurar su operacion
segura.
Sears, Roebuck
and Co., Hoffman
www.sears.com/craftsman
Estates,
IL 60179 U.S.A
TABLE
OF CONTENTS
Introduction
2- 7
Safety symbol and signal word review
.............
Preparing your garage door ......................
Tools needed .................................
Planning
...................................
Carton inventory
Adjust the travel limits .........................
27
3
3
Adjust the force ..............................
28
Test the safety reversal system ..................
29
Test The Protector System ® .....................
29
6
............................
7
Assembly
8-11
Assemble the rail and install the trolley .............
Fasten the rail to the motor unit ...................
27-29
2
4-5
..............................
Hardware inventory
Adjustment
8
9
Operation
30-34
Operation safety instructions
....................
30
Using your garage door opener ..................
30
Using the wall-mounted
31
Door Control .............
To open the door manually
.....................
31
Install the idler pulley ...........................
Install the chain/cable .........................
9
10
Care of your garage door opener
Having a problem? ............................
33
Tighten the chain .............................
11
Diagnostic chart ..............................
34
Installation
11.26
................
Programming
35-36
Installation safety instructions ...................
Determine the header bracket location ............
11
12
To add or reprogram a hand-held remote control
To erase all codes ............................
Install the header bracket
13
3-Function Remotes
14
To add, reprogram or change
a Keyless Entry PIN ...........................
......................
Attach the rail to the header bracket
Position the opener
..............
...........................
15
32
.... 35
35
..........................
35
36
Hang the opener .............................
Install the door control .........................
16
17
Repair
Rail assembly parts ...........................
37
Install the light ...............................
18
Installation parts ..............................
37
Attach the emergency release rope and handle .....
18
Motor unit assembly parts ......................
38
Electrical requirements
19
........................
Parts
37.38
Accessories
39
Install The Protector System ® .................
Fasten the door bracket .....................
20-22
23-24
Warranty
39
Connect the door arm to the trolley ............
25-26
Repair
Parts
and
Service
Backcover
INTRODUCTION
Safety
Symbol
and Signal
Word
Review
This garage door opener has been designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the instructions and warnings contained in this manual.
Mechanical
When you see these Safety Symbols and Signal Words on
the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the
warnings that accompany them. The hazard may come
from something mechanical or from electric shock. Read
the warnings carefully.
Electrical
When you see this Signal Word on the following pages, it
will alert you to the possibility of damage to your garage
door and/or the garage door opener if you do not comply
with the cautionary statements that accompany it. Read
them carefully.
Preparing
your
garage
door
Before you begin:
• Disable locks.
To prevent possible SERIOUSINJURYor DEATH:
• ALWAYScall a trained door systems technician if garage
door binds, sticks, or is out of balance An unbalanced
garage door may not reverse when required
• NEVERtry to loosen, move or adjust garage door, door
springs, cables, pulleys, brackets or their hardware, all of
which are under EXTREMEtension
• Remove any ropes connected to garage door.
• Complete the following test to make sure your garage
door is balanced and is not sticking or binding:
1. Lift the door about halfway as shown. Release the
door. If balanced, it should stay in place, supported
entirely by its springs.
• Disable ALL locks and remove ALL ropes connected to
garage door BEFOREinstalling and operating garage door
opener to avoid entanglement.
2. Raise and lower the door to see if there is any
binding or sticking.
If your door binds, sticks, or is out of balance, call a
trained door systems technician.
To prevent damage to garage door and opener:
• ALWAYSdisable locks BEFOREinstalling and operating the
opener.
• ONLYoperate garage door opener at 120V,60 Hz to avoid
malfunction and damage.
iili
Sectional Door
Tools
One-Piece Door
needed
During assembly, installation and adjustment of the
opener, instructions will call for hand tools as illustrated
below.
Level (optional)
Pencil
Hack Saw
Tape Measure
16 it6
Dnll
D_
and
Stepladder
5/32"
Wire Cutters
Screwdriver
Adjustable
and 1/4"
End Wrench
Planning
Identify the type and height of your garage door. Survey
your garage area to see if any of the conditions below
apply to your installation. Additional materials may be
required. You may find it helpful to refer back to this page
and the accompanying illustrations as you proceed with
the installation of your opener.
Depending on your requirements there are several
installation steps which may call for materials or hardware
not included in the carton.
• Installation Step 1 - Look at the wall or ceiling above
the garage door. The header bracket must be securely
fastened to structural supports.
• Installation Step 5 - Do you have a finished ceiling in
your garage? If so, a support bracket and additional
fastening hardware may be required.
• Installation Step 10- Depending upon garage
construction, extension brackets or wood blocks may be
needed to install sensors.
• Look at the garage door where it meets the floor. Any
gap between the floor and the bottom of the door must
not exceed 1/4" (6 mm). Otherwise, the safety reversal
system may not work properly. See Adjustment Step 3.
Floor or door should be repaired.
SECTIONAL DOOR INSTALLATIONS
• Do you have a steel, aluminum, fiberglass or glass
panel door? If so, horizontal and vertical
reinforcement is required (Installation Step 11).
• The opener should be installed above the center of the
door. If there is a torsion spring or center bearing plate
in the way of the header bracket, it may be installed
within 4 feet (1.22 m) to the left or right of the door
center. See Installation Steps 1 and 11.
• If your door is more than 7 feet (2.13 m) high, see rail
extension kits listed on Accessories page.
• Installation Step 10 -Alternate floor mounting of the
safety reversing sensor will require hardware not
provided.
• Do you have an access door in addition to the garage
door? If not, Model 53702 Emergency Key Release is
required. See Accessories page.
SECTIONAL DOOR INSTALLATION
FINISHED
CEILING
Support
fastening hardware
is required.
See page 16.
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with
glass panels, etc.). See page 23 for details.
Slack in chain tension
is normal when
garage door is closed.
Header Wall
Extension
OR
-
Motor unit
Spring
Torsion Spring
Access Door
Header
,Centerline
iof Garage
I
[
CLOSED
POSITION
Bracket
:;
/
O
Trolley
Stop Bolt
' _=-
_
Trolley
_ _., _r_:_:
_
O
Door
Spring
I T'
I.. I
/_
#ra,g
•
\\
" .LLJ' d
Safety Reversing
Sensor
Safety Reversing Sensor
/.._/
#_
Emergency
Remease
Arm
Gap between floor
and bottom of door
must not exceed 1/4" (6 mm).
F_
_, •
L,na,n
Arm
Rope & Handle
Planning
(Continued)
ONE-PIECE DOOR INSTALLATIONS
• Generally, a one-piece door does not require
reinforcement. If your door is lightweight, refer to the
information relating to sectional doors in Installation
Step 11.
• Depending on your door's construction, you may need
additional mounting hardware for the door bracket
(Step 11).
Without a properly working safety reversal system, persons
(particularly small children) could be SERIOUSLYINJUREDor
KILLED by a closing garage door.
• The gap between the bottom of the garage door and the floor
MUST NOT exceed 1/4" (6 mm). Otherwise, the safety
reversal system may not work properly.
• The floor or the garage door MUST be repaired to eliminate
the gap.
ONE-PIECE DOOR WITHOUT TRACK
FINISHED CEILING
Suppo_ bracket
&fastening
hardwareis required.
See page 16.
7
i
•
Header Wall
Rail
!
.........
Slack in chain tension
is normal when garage
door is closed,
Motor Unit
Wall-mounted
Door Control
CLOSED
Trolley
Safety Reversing
Stop Bolt
Safety Reversing
Sensor
Gap between floor
and bottom of door must not exceed 1/4" (6 mm),
POSITION
Cable
Trolley
Emergency
Release
Rope & Handle
i
Sensor
Curved
Door
Arm
Door
Arm
Garage Door
ONE-PIECE DOOR WITH TRACK
CLOSED
Trolley Stop Bolt
Access
J
_Header
PosmoN
Chain
Cable
Curved
LT_L_
Rail
Bracket
Ol
/_
Door
Door Arr_
......
_
Bracket
Y_TJ'_ Garage
//zl
Door
J
Safety
Reversing Sensor
Reversing
Gap between floor
Sensor
and bottom of door
must not exceed 1/4" (6 ram).
iooooo)j
Door
Straight
Arm
/
L_
Emergency
Release
--Rope &
Handle
Carton
Inventory
Your garage door opener is packaged in one carton
which contains the motor unit and all parts illustrated
below. Accessories will depend on the model purchased.
If anything is missing, carefully check the packing
material. Parts may be stuck in the foam. Hardware for
assembly and installation is shown on the next page.
Save the carton and packing material until installation
and adjustment is complete.
Chain Spreader
SECU RITY,I, ®
3-Function Remote Control
with visor clip (2)
Standard Control Console
Trolley
Rail
Center/Back
Sections
Motor Unit with a Light Lens
Hanging Brackets
Idler Pulley
"U" Bracket
Rail
Fron! (header)
/_f_2
Curved Door
Arm Section
Header Bracket
Door Bracket
2-Conductor Bell Wire
White & White/Red
Safety Sensor
Bracket(2)
The Protector System ®
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with 2-Conductor White & White/Black
Bell Wire attached
Safety Labels
and
Literature
Straight Door
Arm Section
Hardware
Inventory
Separate all hardware and group as shown below for the assembly and installation procedures.
ASSEMBLY HARDWARE
Lock Nut
1/4"-20 (2)
Nut
3/8" (1)
Lock Washer
3/8" (1)
i
Bolt 1/4"-20xl-3/4"
(2)
Master
Link (2)
Trolley Threaded
Idler Bolt (1)
Shaft (1)
INSTALLATION
HARDWARE
©
Carriage Bolt
1/4"-20xl/2"
(2)
Ring
Fastener (3)
Wing Nut
1/4"-20 (2)
Handle
Nut 5/16"-18 (8)
©
Hex Bolt
5/16"-18x7/8"
Lag Screw
5/16"-9xl -5/8" (2)
(4)
LockWasher
5/16" (7)
Insulated
Staples (30)
Lag Screw
5/16"-18xl
Screw
6ABx1-1/4"
-7/8" (2)
(2)
Screw 6-32xl"
(2)
Rope
Carriage Bolt
5/16"-18x2-1/2"
(2)
Drywall Anchors (2)
Spacer (2)
ol
Clevis Pin
5/16"x1-1/2"(1)
Clevis Pin
5/16"x1" (1)
q
Clevis Pin
5/16"x1-1/4"
(1)
ASSEMBLY
Assemble
STEP
1
the Rail & Install
the Trolley
To avoid installation difficulties, do not run the garage
door opener until instructed to do so.
To prevent INJURYfrom pinching, keep hands and fingers
away from the joints while assembling the rail.
The front rail has a cut out "window" at the door end (see
illustration). The hole above this window is larger on
the top of the rail than on the bottom. A smaller hole
3-1/2" (8.9 cm) away is close to the rail edge. Rotate the
back rail so it has a similar hole close to the opposite
edge, about 4-3/4" (12 cm) from the far end.
3. Place the motor unit on packing material to protect the
cover, and rest the back end of the rail on top. For
convenience, put a support under the front end of the
rail.
1. Remove the straight door arm and hanging bracket
packaged inside the front rail and set aside for
Installation Step 5 and 12. NOTE: To prevent INJURY
while unpacking the rail carefully remove the straight
door arm stored within the rail section.
5. Check to be sure there are 4 plastic wear pads inside
the inner trolley. If they became loose during shipping,
check all packing material. Snap them back into
position as shown.
4. As a temporary stop, insert a screwdriver into the hole
10" (25 cm) from the front end of the rail, as shown.
6. Slide the trolley assembly along the rail from the back
end to the screwdriver.
2. Align the rail sections on a flat surface as shown and
slide the tapered ends into the larger ones. Tabs along
the side will lock into place.
Trolley
_ered
End
End
End
Outer Trolley
\
End
Screwdriver
Tabs
Inner Trolley
\
Window
Cut-Out
Idler
PulleyHole
_Wear
Pads
ASSEMBLY
Fasten
the
STEP
Rail
2
to the
Motor
Unit
To avoid SERIOUSdamageto garage door opener, use ONLY
those bolts/fasteners mounted in the top of the opener.
• Insert a 1/4"-20xl-3/4 bolt into the cover protection bolt
hole on the back end of the rail as shown. Tighten
securely with a 1/4"-20 lock nut. Do NOTovertighten.
• Remove the two bolts from the top of the motor unit.
• Place the "U" bracket, flat side down onto the motor unit
and align the bracket hole with the bolt holes. Fasten
with the previously removed bolts.
Chain
Spreader
• Align the rail assembly with the top of the motor unit.
Slide the rail end onto the "U" bracket, all the way to the
stops that protrude on the top and sides of the bracket.
Motor Unit
Sprocket
• Attach spreader to the motor unit with two screws.
"U" Bracket
\
Bolt
\
N
I
HARDWARE
SHOWN
ACTUAL
Protection
Cover
Bolt Hole
SIZE
©
Lock Nut
1/4"-20
Bolt 1/4"-20xl -3/4"
J Lock Nut
ASSEMBLY
Install
the
STEP
Idler
Bolt
Chain and
Cable
3
Pulley
• Lay the chain/cable beside the rail, as shown. Grasp the
end of the cable and pass approximately 12" (30 cm) of
cable through the window. Allow it to hang until
Assembly Step 5.
Washer
Idler
Bolt tl
• Remove the tape from the idler pulley. The inside center
should be pre-greased. If dry, regrease to ensure proper
operation.
_
Screwdriver
Trolley
\
I
I
I
I
I
• Place the idler pulley into the window as shown.
Bolt
I
Trolley
t
• Insert the idler bolt from the top through the rail and
pulley. Tighten with a 3/8" lock washer and nut
underneath the rail until the lock washer is compressed.
Grease
_
Lock
Washer
3/8"
• Rotate the pulley to be sure it spins freely.
I
_._
Stop
Inside Pulley
'_
Idler
Hole
"'",
E
• Insert a 1/4"-20xl-3/4 bolt into the trolley stop hole in
the front of the rail as shown. Tighten securely with a
1/4"-20 lock nut.
Idler
Pulley
HARDWARE
SHOWN
ACTUAL
U
Pulley
_,
SIZE
Jli}_
i/J'Jj
Idler Bolt
Bolt 1/4"-20x1-3/4
Lock Nut 1/4"-20
Nut 3/8"
Lock Washer 3/8"
Lock
Nut
ASSEMBLY
Install
the
STEP
4
Chain/Cable
To avoid possible SERIOUSINJURYto fingers from moving
garage door opener:
• ALWAYSkeep hand clear of sprocket while operating opener.
• Securely attach chain spreader BEFOREoperating.
1. Pull the cable around the idler pulley and toward the
trolley.
2. Connect the cable to the retaining slot on the trolley, as
shown (Figure 1):
• From below, push pins of master link bar up through
cable link and trolley slot.
Dispensing
Carton
Leave
• Push master link cap over pins and past pin notches.
Chain
and
Cable
inside Dispensing
arton
• Slide clip-on spring over cap and onto pin notches
until both pins are securely locked in place.
3. With the trolley against the screwdriver, dispense the
remainder of the cable/chain along the rail toward the
motor unit into the slot on the chain spreader, around
the sprocket onto the chain spreader and continuing to
the trolley assembly. The sprocket teeth must engage
the chain (Figure 2).
to Prevent
Kinking,
Keep Chain and Cable
Taut When Dispensing
Figure 1
Master Link_
Clip-On Sp ri rig "_r_k
4. Check to make sure the chain is not twisted, then
connect it to the threaded shaft with the remaining
master link.
Master
Link Cap
, ,,
Master Link _,-_ _>_.
Clip-On Spring _
5. Thread the inner nut and lock washer onto the trolley
threaded shaft (Figure 3).
Master
6. Insert the trolley threaded shaft through the hole in the
trolley. Be sure the chain is not twisted (Figure 4).
7. Loosely thread the outer nut onto the trolley
threaded shaft.
Trolley
Threaded
Cable
Link
\
8. Remove the screwdriver.
Idler
Pulley
\ Slotted
Hole
_
hie
Figure 2
Master
Link Bar
Chain
"U" Bracket
Spreader
,/
Motor Unit
Sprocket
Figure 3
._
Figure 4
Trolley
Threaded
Shaft
Round
Hole
10
Lock
Washer
5/16"
5/16"
Shaft
Pin
kk
,
j
Notch
i
Round
Hole
Link Bar
ASSEMBLY
Tighten
the
STEP
5
Chain
Figure 1
• Spin the inner nut and lock washer down the trolley
threaded shaft, away from the trolley.
Outer Lock
Nut
Washer
Trolley
Threaded
Shaft
• To tighten the chain, turn outer nut in the direction
shown (Figure 1).
• When the chain is approximately 1/4" (6 mm) above the
base of the rail at its midpoint, re-tighten the inner nut to
secure the adjustment.
Sprocket noise can result if chain is too loose.
Figure 2
When installation is complete, you may notice some chain
droop with the door closed. This is normal. If the chain
returns to the position shown in Figure 2 when the door is
open, do not re-adjust the chain.
Chain
NOTE: During future maintenance, ALWAYS pull the
emergency release handle to disconnect trolley before
adjusting chain. You may notice loosening of chain after
Adjustment Step 3 (Test the Safety Reversal System).
Check for proper tension and readjust chain if necessary.
Then repeat Adjustment Step 3.
i
I
Base of Rail
Mid length of Rail
You have now finished assembling your garage door
opener. Please read the following warnings before
proceeding to the installation section.
INSTALLATION
IMPORTANT INSTALLATION INSTRUCTIONS
To reduce the risk of SEVERE INJURY or DEATH:
1. READAND FOLLOWALL INSTALLATIONWARNINGS
AND INSTRUCTIONS.
8. NEVERwear watches, rings or loose clothing while
installing or servicing opener.They could be caught in
garage door or opener mechanisms.
9. Install wall-mounted garage door control:
• within sight of the garage door.
• out of reach of children at minimum height of 5 feet
2. Install garage door opener only on properly balanced
and lubricated garage door. An improperly balanced
door may not reverse when required and could result in
SEVEREINJURYor DEATH.
3. ALL repairs to cables, spring assemblies and other
hardware MUST be made by a trained door systems
technician BEFOREinstalling opener.
4. Disable ALL locks and remove ALL ropes connected to
garage door BEFOREinstalling opener to avoid
entanglement.
5. Install garage door opener 7 feet (2.13 m) or more
above floor.
(1.5 m).
• away from ALL moving parts of the door.
10. Placeentrapment warning label on wall next to garage
door control.
11. Placemanual release/safety reversetest label in plain
view on inside of garage door.
12. Upon completion of installation, test safety reversal
system. Door MUST reverse on contact with a
1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on
the floor.
6. Mount emergency releasehandle 6 feet (1.83 m) above
floor.
7. NEVERconnect garage door opener to power source
until instructed to do so.
11
INSTALLATION
Determine
Location
the
STEP
Header
1
Unfinished
Oei,og
7---jr
Bracket
_
J _
\ OPT O.AL
__\CEtUNG
J4 MOUNT
_ FOR
._
yj
HEADER
_
BRACKET
Vertical Centerline
of Garage Door
To prevent possible SERIOUSINJURYor DEATH:
• Header bracket MUST be RIGIDLYfastened to structural
support on header wall or ceiling, otherwise garage door
might not reverse when required. DO NOTinstall header
bracket over drywall.
• Concreteanchors MUST be used if mounting header bracket
or 2x4 into masonry.
• NEVERtry to loosen, move or adjust garage door, springs,
cables, pulleys, brackets, or their hardware, all of which are
under EXTREMEtension.
2x4
Structural
Supports
_'
• ALWAYScall a trained door systems technician if garage
door binds, sticks, or is out of balance. An unbalanced
garage door might not reverse when required.
Installation procedures vary according to garage door
types. Follow the instructions which apply to your door.
1. Close the door and mark the inside vertical centerline of
the garage door.
2. Extend the line onto the header wall above the door.
You can fasten the header bracket within 4 feet
(1.22 m) of the left or right of the door center only if
a torsion spring or center bearing plate is in the
way; or you can attach it to the ceiling (see page 13)
when clearance is minimal. (It may be mounted on
the wall upside down if necessary, to gain
approximately
1/2" (1 cm).
2"(5 cm)
Header Wal_
Header Wall
Track
of Travel
X
--Door
If you need to install the header bracket on a 2x4
(on wall or ceiling), use lag screws (not provided)
to securely fasten the 2x4 to structural supports as
shown here and on page 13.
3. Open your door to the highest point of travel as shown.
Draw an intersecting horizontal line on the header wall
above the high point:
Sectional
door with curved track
One-piece
J/7"
Y
Track
Highest Point
of Travel
TT
door with horizontal
track
• 2" (5 cm) above the high point for sectional door and
one-piece door with track.
• 8" (20 cm) above the high point for one-piece door
without track.
This height will provide travel clearance for the top edge
of the door.
Header Wall
l _
8" (20 cm)
Wall
III L8"{28
NOTE: If the total number of inches exceeds the height
available in your garage, use the maximum height
possible, or refer to page 13 for ceiling installation.
Door_
JJjC
/
_
_/of
Highest
i
Highest
Point
:
of Travel
Point
Travel
One-piece door without track:
jamb hardware
12
,
One-piece door without track:
pivot hardware
INSTALLATION
Install
the
Header
STEP
2
Wall Mount
Bracket
You can attach the header bracket either to the wall above
the garage door, or to the ceiling. Follow the instructions
which will work best for your particular requirements. Do
not install the header bracket over drywall. If installing
into masonry, use concrete anchors (not provided).
WALL HEADER BRACKET INSTALLATION
Optional
Mounting
• Center the bracket on the vertical centerline with the
bottom edge of the bracket on the horioontal line as
shown (with the arrow pointing toward the ceiling).
Holes
Vertical
Centerline
• Mark the vertical
holes designated
holes and fasten
support with the
set of bracket holes (do not use the
for ceiling mount). Drill 3/16" pilot
the bracket securely to a structural
hardware provided.
--
Header
Wall--
Door
Lag Screws
5/16"x9x1-5/8"
2x4
Structural
Support
Door Spring
HARDWARE
SHOWN ACTUAL
I
SIZE
Horizontal
Line
Garage
-- Door"_
j-J
Highest Point of
Garage Door Travel
Vertical
Centerline
of Garage Door
Lag Screw
5/16"-9xl -5/8"
CEILING HEADER BRACKET INSTALLATION
• Extend the vertical centerline onto the ceiling as shown.
• Center the bracket on the vertical mark, no more than
6" (15 cm) from the wall. Make sure the arrow is
pointing away from the wall. The bracket can be
mounted flush against the ceiling when clearance
is minimal.
• Mark the side holes. Drill 3/16" pilot holes and fasten
bracket securely to a structural support with the
hardware provided.
•
.-
-Vertical
FinishedCenterline
CeiUing -
[-
of Garage Door
Header
Bracket
6" (15 cm) Maximum
Ceiling Mounting
Door
Spring
Holes
_
Lag Screws
5/16"x9x1-5/8"
-- Header Wall --
Centedine
of Garage Door
13
INSTALLATION
Attach
the
STEP
Rail
to the
3
Header
Bracket
NOTE: (Optional) With some existing installations, you
may re-use the old header bracket with the two plastic
spacers included in the hardware bag. Place the spacers
inside the bracket on each side of the rail, as illustrated.
• Position the opener on the garage floor below the
header bracket. Use packing material as a protective
base. NOTE: If the door spring is in the way you'll need
help. Have someone hold the opener securely on a
temporary support to allow the rail to clear the spring.
• Position the rail bracket against the header bracket.
• Align the bracket holes and join with a clevis pin
5/16"x1-1/2" as shown.
• Insert a ring fastener to secure.
//
//
Idler Pulley
//
//
//
0
/
/
\
Mounting
Hole
Header Bracket
0
<-
Mounting
Hole
OPTION WITH
SOME EXISTING
INSTALLATIONS
Door
Opener Carton or
Support
HARDWARE
SHOWN
Clevis Pin 5/16"x1-1/2"
14
ACTUAL
SIZE
Ring Fastener
INSTALLATION
Position
the
STEP
4
Opener
To prevent damage to garage door, rest garage door opener
rail on 2x4 placed on top section of door.
Follow instructions which apply to your door type as
illustrated.
SECTIONAL
TRACK
DOOR OR ONE-PIECE DOOR WITH
A 2x4 laid flat is convenient for setting an ideal
door-to-rail distance.
Rail
• Remove foam packaging.
i
!.
• Raise the opener onto a stepladder. You will need help
at this point if the ladder is not tall enough.
• Open the door all the way and place a 2x4 laid flat on
the top section beneath the rail.
_l
Door
2x4 is used to determine
tfheco_CtgmOU
• If the top section or panel hits the trolley when you raise
the door, pull down on the trolley release arm
to disconnect inner and outer sections. Slide the outer
trolley toward the motor unit. The trolley can remain
disconnected until Installation Step 12 is completed.
ntin g height
ENGAGED
ONE-PIECE DOOR WITHOUT TRACK
A 2x4 on its side is convenient for setting an ideal door-torail distance.
• Remove foam packaging.
• Raise the opener onto a stepladder. You will need help
at this point if the ladder is not tall enough.
• Open the door all the way and place a 2x4 on its side
on the top section of the door beneath the rail.
L_
2x4 is used to determine
the correct mounting height
from ceiling.
• The top of the door should be level with the top of the
motor unit. Do not position the opener more than
4" (10 cm) above this point.
15
INSTALLATION
Hang
the
STEP
5
Opener
To avoid possible SERIOUSINJURYfrom a falling garage door
opener, fasten it SECURELYto structural supports of the
garage. Concrete anchors MUST be used if installing any
brackets into masonry.
Three representative installations are shown. Yours may
be different. Hanging brackets should be angled (Figure 1)
to provide rigid support. On finished ceilings (Figure 2 and
Figure 3), attach a sturdy metal bracket to structural
supports before installing the opener. This bracket and
fastening hardware are not provided.
1. Measure the distance from each side of the motor unit
to the structural support.
Figure 1
Structural
Supports
\
2. Cut both pieces of the hanging bracket to required
lengths.
Lag Screws
5/16"-18xl -7/8"
3. Drill 3/16" pilot holes in the structural supports.
Measure
i
4. Attach one end of each bracket to a support with
5/16"-18xl -7/8" lag screws.
Distance
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
5. Fasten the opener to the hanging brackets with
5/16"-18x7/8" hex bolts, lock washers and nuts.
6. Check to make sure the rail is centered over the door
(or in line with the header bracket if the bracket is not
centered above the door).
Figure 2
7. Remove the 2x4. Operate the door manually. If the door
hits the rail, raise the header bracket.
NOTE: DO NOT connect power to opener at this time.
FINISHED CEILING
\
.....
HARDWARE
SHOWN
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
ACTUAL SIZE
Lag Screw 5/16"-18xl
"(Not Provided)
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
W/8"
Figure 3
Hex Bolt
5/16"-18x7/8"
Nut 5/16"-18
Lock Washer
5/16"
Lag Screws
5/16"-18xl -7/8"
(Not Provided)
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
Nut 5/16"-18
16
FINISHED CEILING
Bolt 5/16"-18x7/8"
Lock Washer 5/16"
INSTALLATION
Install
the
Door
STEP
6
Control
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
Locate door control within sight of door, at a minimum
height of 5 feet (1.5 m) where small children cannot reach,
away from moving parts of door and door hardware.
If installing into drywall, drill 5/32" holes and use the
anchors provided. For pre-wired installations (as in new
home construction), it may be mounted to a single gang
box (Figure 2).
• Be sure power is not connected BEFOREinstalling door
control.
• Connect ONLYto 24 VOLTlow voltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a closing
garage door:
• Install door control within sight of garage door, out of reach
of children at a minimum height of 5 feet (1.5 m), and away
from all moving parts of door.
• NEVERpermit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLYwhen it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYSkeepgarage door in sight until completely closed.
NEVERpermit anyone to cross path of closing garage door.
1 .Strip 7/16" (11 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back of
door control by color: white wire to 2 and white/red wire
to the 1.
2. Remove cover by gently prying along one side with a
screwdriver (Figure 1). Fasten with 6ABx1-1/4"
self-tapping screws (drywall installation) or 6-32xl"
machine screws (into gang box) as follows:
• Install bottom screw, allowing 1/8" (3 mm) to protrude
above wall surface.
Outside Keylock Accessory Connections
To opener quick-connect terminals: white to white;
white/red to red.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid cracking
plastic housing. Do not overtighten.
HARDWARE
ACTUAL
• Insert top tabs and snap on cover.
Door Control Button
3. (For standard installation only) Run bell wire up wall
and across ceiling to motor unit. Use insulated staples
to secure wire in several places. Do not pierce wire with
a staple, creating a short or open circuit.
Insulated
Staples
Control Console (std installation)
4. Strip 7/16" (11 mm) of insulation from end of bell wire.
Connect bell wire to the quick-connect terminals as
follows: white to white and white/red to red.
Control Console (pre-wired)
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires into
quick-connect holes: white to white and red/white to red.
5. Position the antenna wire as shown.
Drywall Anchors
Figure I
REMOVE & REPLACE
To Replace,
Insert
Top Tabs
First
6. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent location
on inside of garage door.
NOTE: DO NOT connect power and operate opener at
this time. The trolley will travel to the full open
position but will not return to the close position
until the sensor beam is connected and properly
aligned.
SHOWN
SIZE
Figure 2
COVER
PRE-WIRED
INSTALLATION
To Remove,
Twist
Here
24 Volt
2-Conductor
Bell Wire
Lighted
Push Butto__
Quick-Connect
2-Conductorll
Wire
Terminals
STANDARD
CONTROL CONSOLE
STANDARD CONTROL
'BACK VIEW)
Top
Mounting
Hole
Terminal
Screws
Antenna
Bell
Wire
17
Bottom
Mounting
Hole
I
INSTALLATION
Install
the
STEP
7
Light
To prevent possible OVERHEATING
of the endpanel or light
socket,
• DO NOT use short neck or specialty light bulbs.
• DO NOT use halogen bulbs. Use ONLYincandescent.
To prevent damage to the opener:
• DO NOT use bulbs larger than IOOW.
• ONLYuse A19 size bulbs.
• Press the release tabs on both sides of lens. Gently
rotate lens back and downward until the lens hinge is in
the fully open position. Do not remove the lens.
• Install up to a 100 watt maximum light bulb in the
socket. The light will turn ON and remain lit for
approximately 4-1/2 minutes when power is connected.
Then the light will turn OFR
• Reverse the procedure to close the lens.
100 Watt (Max)
Standard
Light Bulb
• Use A19, standard neck garage door opener bulbs for
replacement.
Release Tab
NOTE: Use only a standard light bulb. The use of short
neck or speciafity light bulb may overheat the endpanel or
light socket.
INSTALLATION
Attach
the
and Handle
STEP
Emergency
\
\
8
Release
Rope
To prevent possible SERIOUSINJURYor DEATHfrom a failing
garage door:
• If possible, use emergency releasehandle to disengage
trolley ONLYwhen garage door is CLOSED.Weak or broken
springs or unbalanceddoor could result in an open door
failing rapidly and/or unexpectedly.
• NEVERuse emergency releasehandle unless garage
doorway is clear of persons and obstructions.
• NEVERuse handle to pull door open or closed. If rope knot
becomes untied, you could fall.
• Thread one end of the rope through the hole in the top
of the red handle so "NOTICE" reads right side up as
shown. Secure with an overhand knot at least 1"
(2.5 cm) from the end of the rope to prevent slipping.
• Thread the other end of the rope through the hole in the
release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet (1.83 m)
above the floor. Ensure that the rope and handle clear
the tops of all vehicles to avoid entanglement. Secure
with an overhand knot.
Trolley
NOTE: If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.
Emergency
Release Handle
18
_K Overhand
not
INSTALLATION
Electrical
STEP
9
Requirements
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution or fire:
To avoid installation difficulties, do not run the opener
at this time.
• Be sure power is not connected to the opener, and
disconnect power to circuit BEFOREremoving cover to
establish permanent wiring connection.
• Garagedoor installation and wiring MUST be in compliance
with all local electrical and building codes.
• NEVERuse an extension cord, 2-wire adapter, or change
plug in any way to make it fit outlet. Be sure the opener is
grounded.
To reduce the risk of electric shock, your garage door
opener has a grounding type plug with a third grounding
pin. This plug will only fit into a grounding type outlet. If
the plug doesn't fit into the outlet you have, contact a
qualified electrician to install the proper outlet.
PERMANENT
CONNECTION
WIRING
Ground Tab
If permanent wiring is required by your local code,
refer to the following procedure.
Green
Ground Screw
To make a permanent connection through the 7/8" hole in
the top of the motor unit:
• Remove the motor unit cover screws and set the cover
aside.
\
Black
Wire
Ground Wire
• Remove the attached 3-prong cord.
White Wire
• Connect the black (line) wire to the screw on the brass
terminal; the white (neutral) wire to the screw on the
silver terminal; and the ground wire to the green ground
screw. The opener must be grounded.
• Reinstall the cover.
To avoid installation
at this time.
difficulties,
do not run the opener
19
INSTALLATION
Install
The
STEP
Protector
10
System
®
Be sure power is not connectedto the garage door opener
BEFOREinstalling the safety reversing sensor.
To prevent SERIOUSINJURYor DEATHfrom a closing
garage door:
• Correctly connect and align the safety reversing sensor. This
required safety device MUST NOTbe disabled.
• Install the safety reversing sensor so beam is NO HIGHER
than 6" (15 cm) above garage floor.
The safety reversing sensor must be connected and
aligned correctly before the garage door opener will
move in the down direction.
IMPORTANT INFORMATION ABOUT THE SAFETY
REVERSING SENSOR
When properly connected and aligned, the sensor will
detect an obstacle in the path of its electronic beam. The
sending eye (with an amber indicator light) transmits an
invisible light beam to the receiving eye (with a green
indicator light). If an obstruction breaks the light beam
while the door is closing, the door will stop and reverse to
full open position, and the opener lights will flash 10 times.
If it is necessary to mount the units on the wall, the
brackets must be securely fastened to a solid surface
such as the wall framing. Extension brackets (see
accessories) are available if needed. If installing in
masonry construction, add a piece of wood at each
location to avoid drilling extra holes in masonry if
repositioning is necessary.
The units must be installed inside the garage so that the
sending and receiving eyes face each other across the
door, no more than 6" (15 cm) above the floor. Either can
be installed on the left or right of the door as long as the
sun never shines directly into the receiving eye lens.
The invisible light beam path must be unobstructed. No
part of the garage door (or door tracks, springs, hinges,
rollers or other hardware) may interrupt the beam while
the door is closing.
The mounting brackets are designed to clip onto the track
of sectional garage doors without additional hardware.
Safety Reversing Sensor
6" (15 crn) max, above floor
Protection Area
Facing the door from inside the garage
2O
INSTALLING THE BRACKETS
Be sure power to the opener is disconnected.
Install
and align the brackets so the sensors will face each other
across the garage door, with the beam no higher than
6" (15 cm) above the floor. They may be installed in one of
three ways, as follows.
Garage door track installation
Figure 1
DOOR TRACK
MOUNT (RIGHT SIDE)
Door
Track
(preferred):
Indicator
Light
• Slip the curved arms over the rounded edge of each
door track, with the curved arms facing the door. Snap
into place against the side of the track. It should lie
flush, with the lip hugging the back edge of the track, as
shown in Figure 1.
Sensor
Bracket
If your door track will not support the bracket securely,
wall installation is recommended.
Wall installation
(Figure 2 & 3):
• Place the bracket against the wall with curved arms
facing the door. Be sure there is enough clearance for
the sensor beam to be unobstructed.
WALL MOUNT (RIGHT SIDE)
Fasten Wood Block to Wall with
Figure 2
//Lag
Screws
(Not Provided)
Indicator
Light
• If additional depth is needed, an extension bracket (See
Accessories) or wood blocks can be used.
• Use bracket mounting holes as a template to locate and
drill (2) 3/16" diameter pilot holes on the wall at each
side of the door, no higher than 6" (15 cm) above the
floor.
Sensor
Bracket
(Not Provided)
Lens
• Attach brackets to wall with lag screws (Not provided).
• If using extension brackets or wood blocks, adjust right
and left assemblies to the same distance out from the
mounting surface. Make sure all door hardware
obstructions are cleared.
Floor installation
Figure 3
WALL MOUNT
<_r
d;ll
(Figure 4):
• Use wood blocks or extension brackets (See
Accessories) to elevate sensor brackets so the lenses
will be no higher than 6" (15 cm) above the floor.
(RIGHT SIDE)
Extension
Bracket
(See Accessories)
(Provided with
Extension Brackel
• Carefully measure and place right and left assemblies at
the same distance out from the wall. Be sure all door
hardware obstructions are cleared.
• Fasten to the floor with concrete anchors as shown.
Sensor
Bracket
(Provided with
Extension
Bracket)
_"
Indicator
Light
Lens
Figure 4
HARDWARE
Carriage Bolt
1/4"-20xl/2"
SHOWN
ACTUAL
Wing Nut
1/4"-20
FLOOR
MOUNT (RIGHT SIDE)
SIZE
_i_
J
Attach with
i!
Concrete Anchors
(Not Provided)
Indicator
Staples
Light
Bracket
21
MOUNTING AND WIRING THE SAFETY REVERSING
SENSORS
Figure 5
Wing Nut
1/4"-20
• Slide a 1/4"-20xl/2" carriage bolt head into the slot on
each sensor. Use wing nuts to fasten sensors to
brackets, with lenses pointing toward each other across
the door. Be sure the lens is not obstructed by a bracket
extension (Figure 5).
Carriage Bolt
1/4"-20xl/2"
--_
"Lens
• Finger tighten the wing nuts.
• Run the wires from both sensors to the opener. Use
insulated staples to secure wire to wall and ceiling.
TROUBLESHOOTING
SENSORS
• Strip 7/16" (11 mm) of insulation from each set of wires.
Separate white and white/black wires sufficiently to
connect to the opener quick-connect terminals. Twist
like colored wires together. Insert wires into quickconnect holes: white to white and white/black to grey
(Figure 6).
THE SAFETY REVERSING
1. If the sending eye indicator light does not glow steadily
after installation, check for:
• Electric power to the opener.
• A short in the white or white/black wires. These can
occur at staples, or at opener connections.
• Incorrect wiring between sensors and opener.
• A broken wire.
ALIGNING THE SAFETY REVERSING SENSORS
• Plug in the opener. The indicator lights in both the
sending and receiving eyes will glow steadily if wiring
connections and alignment are correct.
2. If the sending eye indicator light glows steadily but the
receiving eye indicator light doesn't:
• Check alignment.
The sending eye amber indicator light will glow regardless
of alignment or obstruction. If the green indicator light in
the receiving eye is off, dim, or flickering (and the invisible
light beam path is not obstructed), alignment is required.
• Check for an open wire to the receiving eye.
3. If the receiving eye indicator light is dim, realign
either sensor.
• Loosen the sending eye wing nut and readjust, aiming
directly at the receiving eye. Lock in place.
NOTE: When the invisible beam path is obstructed or
misaligned while the door is closing, the door will reverse.
If the door is already open, it will not close. The opener
lights will blink 10 times. See page 20.
• Loosen the receiving eye wing nut and adjust sensor
until it receives the sender's beam. When the green
indicator light glows steadily, tighten the wing nut.
Figure 6
Bell Wire
Bell Wire
l
1. Strip wire 7/16"
(11 mm)
7,16" (11 m41)
2. Twist like colored
wires together
3. Insert into
appropriate
/
Safety Reversing
Sensor
Invisible Light Beam
Protection Area
/
Red
Safety Reversing
Sensor
White
Quick-Connect
22
terminals
Grey
Terminals
INSTALLATION
Fasten
the
Door
STEP
11
Bracket
Fiberglass, aluminum or lightweight steel garage doors WILL
REQUIREreinforcement BEFOREinstallation of door bracket.
Contact your door manufacturer for reinforcement kit.
Follow instructions which apply to your door type
as illustrated below or on the following page.
A horizontal reinforcement brace should be long
enough to be secured to two vertical supports. A
vertical reinforcement brace should cover the height
of the top panel.
HARDWARE
The illustration shows one piece of angle iron as the
horizontal brace. For the vertical brace, two pieces of
angle iron are used to create a U-shaped support
(Figure 1). The best solution is to check with your garage
door manufacturer for an opener installation door
reinforcement kit.
SHOWN
ACTUAL
©
©
Nut 5/16"-18
NOTE: Many vertical brace installations provide for direct
attachment of the clevis pin and door arm. In this case you
will not need the door bracke# proceed to Installation
Step 12.
SIZE
LockWasher
5/16"
Carriage Bolt
5/16"-18x2-1/2"
SECTIONAL DOORS
• Center the door bracket on the previously marked
vertical centerline used for the header bracket
installation. Note correct UP placement, as stamped
inside the bracket (Figure 2).
• Position the bracket on the face of the door within the
following limits:
• Mark and drill 5/16" left and right fastening holes.
Secure the bracket as shown in Figure 1 if there is
vertical reinforcement.
If your installation doesn't require vertical reinforcement
but does need top and bottom fastening holes for the door
bracket, fasten as shown in Figure 2.
A) The top edge of the bracket 2"-4" (5-10 cm) below
the top edge of the door.
B) The top edge of the bracket directly below any
structural support across the top of the door.
Header Bracket
Horizontal and vertical reinforcement
is needed for lightweight
garage doors
(fiberglass, aluminum, steel, doors with
glass panel, etc.). (Not Provided)
Vertical
Reinforcement
Vertical
Centerline
//of Garage
,' Door
UP
Carriage Bolt
ge
of Door or
einforcement
Board
Door
Bracket
Lock Washer
5/16"
-_(
Nut
5/16"-18
z .....
Figure 1
Door Bracket
23
Figure 2
ONE-PIECE
DOORS
Please read and comply with the warnings and
reinforcement instructions on the previous page. They
apply to one-piece doors also.
• Center the door bracket on the top of the door, in line
with the header bracket as shown. Mark either the left
and right, or the top and bottom holes.
• Drill 5/16" pilot holes and fasten the bracket with
hardware supplied.
HARDWARE
SHOWN ACTUAL
©
If the door has no exposed framing, drill 3/16" pilot holes
and fasten the bracket with 5/16"x1-1/2" lag screws (not
provided) to the top of the door.
©
Nut 5/16"-18
NOTE: The door bracket may be installed on the top edge
of the door if required for your installation, (Refer to the
dotted line optional placement drawing.) Drill 3/16" pilot
holes and substitute 5/16"x1-1/2" lag screws (not
provided) to fasten the bracket to the door,
SIZE
LockWasher
5/16"
Carriage Bolt
5/16"-18x2-1/2"
Header Wall
2x4
Horizontal and vertical
reinforcement
{s needed for
lightweight
garage doors
(fiberglass,
aluminum,
steeU,
door with glass panel, etc.).
(Not Provided)
Header
Bracket
Door
Bracket
Optional
Placement
of Door
Bracket
®
Vertical
8J16.48"$
Washer
Lock
of Garage
Door
'
Door
Bracket
5/16"
Top of Door
(Inside Garac
Top Edge
of Door
Optional
Placement
Carriage Bolt
For a door with no exposed framing,
or for the optional installation, use
5/16"xl-1/2"
lag screws (Not Provided)
to fasten door bracket,
24
5/16"-18x2-1/2"
INSTALLATION
Connect
Door
STEP
Arm
12
to Trolley
Follow instructions which apply to your door type as
illustrated below and on the following page.
SECTIONAL DOORS ONLY
• Make sure garage door is fully closed. Pull the
emergency release handle to disconnect the outer trolley
from the inner trolley. Slide the outer trolley back (away
from the pulley) about 8" (20 cm) as shown in Figures 1,
2 and 3.
• Figure 1:
- Fasten straight door arm section to outer trolley with
the 5/16"x1" clevis pin. Secure the connection with a
ring fastener.
- Fasten curved section to the door bracket in the same
way, using the 5/16"x1-1/4" clevis pin.
Figure 1
• Figure 2:
Pulley
- Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far apart
as possible to increase door arm rigidity.
• Figure 3, Hole alignment
alternative:
- If holes in curved arm are above holes in straight arm,
disconnect straight arm. Cut about 6" (15 cm) from the
solid end. Reconnect to trolley with cut end down as
shown.
- Bring arm sections together.
- Find two pairs of holes that line up and join with bolts,
lock washers and nuts.
"5
• Pull the emergency release handle toward the opener at
a 45 ° angle so that the trolley release arm is horizontal.
Proceed to Adjustment Step 1, page 27. Trolley will
re-engage automatically when opener is operated.
""_/
Bolts
5/16"-18x7/8"
Door Bracket
Figure 2
Pulley
',, i
i
'_ii(-,- 8" (20 cra) rain.
_),,
HARDWARE
SHOWN
J
ACTUAL SIZE
Trolley
/ /
Stop Bolt
//
Lock
/o/
Washers/oy
5/16"
/o7
Nuts
Nut 5/16"-18
G
Clevis Pin
5/16"xl" (Trolley)
Lock Washer 5/t 6"
........
'_,___
1
Ring Fastener
Clevis Pin
Hex Bolt
5/16"xl -1/4" (Door Bracket)
5/16"-18x7/8"
"-7:7 % .' Bo,ts
/
/
o1_
Figure 3
25
"---.
Cut this end
= ....
ALL ONE-PIECE DOORS
1.Assemble
Door
Bracket
the door arm, Figure 4:
Fastener
Clevis Pin
5/16"x1-1/4"
• With the door closed, connect the straight door arm
section to the door bracket with the 5/16"x1-1/4"
clevis pin.
procedures,
- Press the Door Control push button. The trolley will
travel to the fully closed position.
• On one-piece doors, before connecting the door arm
to the trolley, the travel limits must be adjusted. Limit
adjustment screws are located on the left side panel
as shown on page 27. Follow adjustment procedures
below.
decrease
- Manually close the door and lift the door arm to the
trolley. The arm should touch the trolley just ahead of
the door arm connector hole. Refer to the fully closed
trolley/door arm positions in the illustration. If the arm
is behind the connector hole, adjust the limit further.
One full turn equals 2" (5 cm) of trolley travel.
UP travel limit
- Turn the UP limit adjustment screw counter-clockwise
4 turns.
3. Connect the door arm to the trolley:
• Close the door and join the curved arm to the
connector hole in the trolley with the remaining clevis
pin. It may be necessary to lift the door slightly to make
the connection.
- Press the Door Control push button. The trolley will
travel to the fully open position.
- Manually raise the door to the open position (parallel
to the floor), and lift the door arm to the trolley. The
arm should touch the trolley just in back of the door
arm connector hole. Refer to the fully open
trolley/door arm positions in the illustration. If the arm
does not extend far enough, adjust the limit further.
One full turn equals 2" (5 cm) of trolley travel.
• Closed door adjustment:
limit
decrease
• Secure with a ring fastener.
• Run the opener through a complete travel cycle. If the
door has a slight "backward" slant in full open position
as shown in the illustration, decrease the UP limit until
the door is parallel to the floor.
NOTE: When setting the up limit on the following page, the
door should not have a "backward" slant when fully open
as illustrated below. A slight backward slant will cause
unnecessary bucking and/or jerking operation as the door
is being opened or closed from the fully open position.
DOWN travel
- Turn the DOWN limit adjustment screw clockwise
4 complete turns.
Figure 5
Curved
Door Arm
Figure 4
Figure 5:
• Open door adjustment:
Straight
Arm
Bolts
5/16"-18x7/8"
• Secure with a ring fastener.
2. Adjustment
Nuts
5/16"-18
Lock
Washers
5/16"
• Fasten the straight and curved door arm sections
together to the longest possible length (with a 2 or 3
hole overlap).
Inner Trolley
cy Release Handle
Inner Trolley
Outer Trolley
Correct Angle
_C _";
Backward Slant
(Incorrect)
Open Door
26
ADJUSTMENT
Adjust
the
STEP
UP and
DOWN
1
Travel
Limits
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLYINJUREDor
KILLED by a closing garage door.
• Incorrect adjustment of garage door travel limits will
interfere with proper operation of safety reversal system.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal system
MUST be tested. Door MUST reverse on contact with 1-1/2"
high (3.8 cm) object (or 2x4 laid flat) on floor.
Limit adjustment settings regulate the points at which the
door will stop when moving up or down.
To operate the opener, press the Door Control push bar.
Run the opener through a complete travel cycle.
• Does the door open and close completely?
• Does the door stay closed and not reverse
unintentionally when fully closed?
If your door passes both of these tests, no limit
adjustments are necessary unless the reversing test fails
(Adjustment Step 3, page 29).
Adjustment procedures are outlined below. Read the
procedures carefully before proceeding to Adjustment
Step 2. Use a screwdriver to make limit adjustments. Run
the opener through a complete travel cycle after each
adjustment.
To prevent damage to vehicles, be sure fully open door
provides adequate clearance.
NOTE: Repeated operation of the opener during
adjustment procedures may cause the motor to overheat
and shut off. Simply wait 15 minutes and try again. If
anything interferes with the door's upward travel, it will
stop. If anything interferes with the door's downward
travel (including binding or unbalanced doors), it will
reverse.
Cover Protection
Bolt
U
HOW AND WHEN TO ADJUST THE LIMITS
• If the door does not open completely but opens at
least five feet (1.5 m):
Increase up travel. Turn the UP limit adjustment screw
clockwise. One turn equals 2" (5 cm) of travel.
Left Side Panel
NOTE: To prevent the trolley from hitting the cover
protection bolt, keep a minimum distance of 2-4"
(5 cm - 10 cm) between the trolley and the boll
Limit Adjustment
Screws
• If door does not open at least 5 feet (1.5 m):
Adjust the UP (open) force as explained in Adjustment
Step 2.
ADJUSTMENT
LABEL
• If the door does not close completely:
Increase down travel. Turn the down limit adjustment
screw counterclockwise. One turn equals 2" (5 cm) of
travel.
• If the door reverses when closing and there is no
visible interference to travel cycle:
If door still won't close completely and the trolley bumps
into the pulley bracket (page 4), try lengthening the door
arm (page 25) and decreasing the down limit.
If the opener lights are flashing, the Safety Reversing
Sensors are either not installed, misaligned, or
obstructed. See Troubleshooting, page 22.
• If the opener reverses in fully closed position:
Test the door for binding: Pull the emergency release
handle. Manually open and close the door. If the door is
binding or unbalanced, call for a trained door systems
technician. If the door is balanced and not binding,
adjust the DOWN (close) force. See Adjustment Step 2.
Decrease down travel. Turn the down limit adjustment
screw clockwise. One turn equals 2" (5 cm) of travel.
27
ADJUSTMENT
Adjust
the
STEP
2
Force
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLYINJUREDor
KILLED by a closing garage door.
• Too much force on garage door will interfere with proper
operation of safety reversal system.
• NEVERincrease force beyond minimum amount required to
close garage door.
• NEVERuse force adjustments to compensate for a binding
or sticking garage door.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal system
MUST be tested. Door MUST reverse on contact with 1-1/2"
high (3.8 cm) object (or 2x4 laid flat) on floor.
Force adjustment controls are located on the back panel
of the motor unit. Force adjustment settings regulate the
amount of power required to open and close the door.
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down direction
and stops in the up direction. Weather conditions can
affect the door movement, so occasional adjustment may
be needed.
The maximum force adjustment range is about 3/4 of a
complete turn. Do not force controls beyond that
point. Turn force adjustment controls with a screwdriver.
NOTE: If anything interferes with the door's upward travel,
it will stop. If anything interferes with the door's downward
travel (including binding or unbalanced doors), it will
reverse.
HOW AND WHEN TO ADJUST THE FORCES
Force Adjustment
Controls
1. Test the DOWN (close) force
Back Panel
• Grasp the door bottom when the door is about halfway
through DOWN (close) travel. The door should
reverse. Reversal halfway through down travel does
not guarantee reversal on a 1-1/2" (3.8 cm)
obstruction. See Adjustment Step 3, page 29. If the
door is hard to hold or doesn't reverse,
DECREASE the DOWN (close) force by turning
the control counterclockwise. Make small adjustments
until the door reverses normally. After each
adjustment, run the opener through a complete cycle.
I
• If the door reverses during the down (close) cycle
and the opener lights aren't flashing, INCREASE
DOWN (close) force by turning the control clockwise.
Make small adjustments until the door completes a
close cycle. After each adjustment, run the opener
through a complete travel cycle. Do not increase the
force beyond the minimum amount required to close
the door.
J
ADJUSTMENT
LABEL
2. Test the UP (open) force
• Grasp the door bottom when the door is about halfway
through UP (open) travel. The door should stop. If the
door is hard to hold or doesn't stop, DECREASE
UP (open) force by turning the control
counterclockwise. Make small adjustments until the
door stops easily and opens fully. After each
adjustment, run the opener through a complete
travel cycle.
Open Force
• If the door doesn't open at least 5 feet (1.5 m),
INCREASE UP (open) force by turning the control
clockwise. Make small adjustments until door opens
completely. Readjust the UP limit if necessary. After
each adjustment, run the opener through a complete
travel cycle.
28
Close Force
ADJUSTMENT
Test
the
Safety
STEP
3
Reversal
System
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLYINJUREDor
KILLED by a closing garage door.
• Safety reversal system MUST be tested every month.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal system
MUST be tested. Door MUST reverse on contact with 1-1/2"
high (3.8 cm) object (or 2x4 laid flat on the floor.
TEST
• With the door fully open, place a 1-1/2" (3.8 cm) board
(or a 2x4 laid flat) on the floor, centered under the
garage door.
• Operate the door in the down direction. The door must
reverse on striking the obstruction.
ADJUST
• If the door stops on the obstruction, it is not traveling far
enough in the down direction. Increase the DOWN limit
by turning the DOWN limit adjustment screw
counterclockwise 1/4 turn.
A
NOTE: On a sectional door, make sure limit
adjustments do not force the door arm beyond a straight
up and down position. See the illustration on page 25.
_:z:
_7 _::z_7
:::_7_7 z:_z _7 z:_:_7
::zT_:
• Repeat the test.
• When the door reverses on the 1-1/2" (3.8 cm) board,
remove the obstruction and run the opener through 3 or
4 complete travel cycles to test adjustment.
• If the unit continues to fail the Safety Reverse Test, call
for a trained door systems technician.
IMPORTANT SAFETY CHECK:
Test the Safety Reverse System after:
• Each adjustment of door arm length, limits, or force
controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
=
(or a 2x4 laid flat)
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
ADJUSTMENT
Test
The
Protector
STEP
4
System
®
Without a properly installed safety reversing sensor, persons
(particularly small children) could be SERIOUSLYINJUREDor
KILLED by a closing garage door.
• Press the remote control push button to open the door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the door.
The door will not move more than an inch (2.5 cm), and
the opener lights will flash.
The garage door opener will not close from a remote if the
indicator light in either sensor is off (alerting you to the fact
that the sensor is misaligned or obstructed).
If the opener closes the door when the safety
reversing sensor is obstructed (and the sensors are
no more than 6" (15 cm) above the floor), call for a
trained door systems technician.
Safety Reversing Sensor
29
OPERATION
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of SEVERE INJURY or DEATH:
1. READAND FOLLOWALL WARNINGSAND
INSTRUCTIONS.
2. ALWAYSkeep remote controls out of reach of children.
NEVERpermit children to operate or play with garage door
control push buttons or remote controls.
3. ONLYactivate garage door when it can be seen clearly, it is
properly adjusted, and there are no obstructions to door
travel.
4. ALWAYSkeep garage door in sight until completely
closed. NO ONESHOULDCROSSTHE PATHOFTHE
MOVING DOOR.
5. NO ONESHOULDGO UNDERA STOPPED,PARTIALLY
OPENEDDOOR.
6. If possible, use emergency release handle to disengage
trolley ONLYwhen garage door is CLOSED.Weak or
broken springs or unbalanceddoor could result in an open
door failing rapidly and/or unexpectedly.
7. NEVERuse emergency releasehandle unless garage
doorway is clear of persons and obstructions.
8. NEVERuse handle to pull garage door open or closed. If
rope knot becomes untied, you could fall.
Using
Your
Garage
Door
9. If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
10. After ANY adjustments are made, the safety reversal
system MUST be tested.
11. Safety reversal system MUST be tested every month.
Garagedoor must reverse on contact with 1-1/2" high
(3.8 cm) object (or a 2x4 laid flat) on the floor.
12. ALWAYSKEEPGARAGEDOORPROPERLYBALANCED
(see page 3). An improperly balanced door may not
reverse when required and could result in SEVERE
INJURYor DEATH.
13. ALL repairs to cables, spring assemblies and other
hardware, ALL of which are under EXTREMEtension,
MUST be made by a trained door systems technician.
14. ALWAYSdisconnect electric power to garage door opener
BEFOREmaking any repairs or removing covers.
15SAVETHESEINSTRUCTIONS.
6. If obstructed while opening, the door will stop.
Opener
7. If fully open, the door will not close when the beam is
broken. The sensor has no effect in the opening cycle.
Your Security+ ®opener and hand-held remote control
have been factory-set to a matching code which changes
with each use, randomly accessing over 100 billion new
codes. Your opener will operate with up to eight
Security+ ® remote controls and one Security+ ®Keyless
Entry System. If you purchase a new remote, or if you
wish to deactivate any remote, follow the instructions in
the Programming section.
If the sensor is not installed, or is misaligned, the door
won't close from a hand-held remote. However, you can
close the door with the Door Control, the Outdoor Key
Switch, or Keyless Entry, if you activate them until down
travel is complete. If you release them too soon, the door
will reverse.
The opener lights will turn on under the following
conditions: when the opener is initially plugged in; when
power is restored after interruption; when the opener is
activated. They will turn off automatically after 4-1/2
minutes. Bulb size is A19. Power is 100 watts maximum.
Lights will also turn on when someone walks through the
open garage door.
Activate your opener with any of the following:
• The hand-held Remote Control: Hold the large push
button down until the door starts to move.
• The wall-mounted Door Control: Hold the push button
or bar down until the door starts to move.
• The Keyless Entry (See Accessories): If provided with
your garage door opener, it must be programmed
before use. See Programming.
When the opener is activated (with the safety
reversing sensor correctly installed and aligned)
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop.
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse. If the
obstruction interrupts the sensor beam, the opener
lights will blink for five seconds.
30
Using
the
Wall.Mounted
Door
Press the lighted push button to open
or close the door. Press again to
reverse the door during the closing
cycle or to stop the door while it's
opening.
To Open
Control
I
the
Door
Manually
To prevent possible SERIOUSINJURYor DEATHfrom a failing
garage door:
• If possible, use emergency releasehandle to disengage
trolley ONLYwhen garage door is CLOSED.Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
• NEVERuse emergency releasehandle unless garage
doorway is clear of persons and obstructions.
• NEVERuse handle to pull door open or closed. If rope knot
becomes untied, you could fall.
DISCONNECT
THE TROLLEY:
The door should be fully closed
if possible. Pull down on the
emergency release handle (so
that the trolley release arm
snaps into a vertical position)
and lift the door manually. The
lockout feature prevents the
trolley from reconnecting
automatically, and the door can
be raised and lowered
manually as often as
necessary.
Trolley
Trolley
Release Arm
(In Manual
Disconnect
Position)
Lockout position
(Manual disconnect)
TO RE-CONNECT
TROLLEY:
THE
Pull the emergency release
handle toward the opener at
an angle so that the trolley
release arm is horioontal. The
trolley will reconnect on the
next UP or DOWN operation,
either manually or by using
the door control or remote.
Trolley
Emergency
""_
Release Handle . %_
(Down and Back) " _'
To reconnect
31
CARE OF YOUR
OPENER
GARAGE
LIMIT AND FORCE
ADJUSTMENTS:
Weather conditions may cause
some minor changes in door
operation requiring some readjustments, particularly during
the first year of operation
THE REMOTE CONTROL BATTERY
DOOR
FORCE
CONTROLS
To prevent possible SERIOUSINJURYor DEATH:
• NEVERallow small children near batteries
• If battery is swallowed, immediately notify doctor
The lithium battery should
produce power for up to
LIMITCONTROLS
openthisend
first to avoidJ
_...._
5 years To replace battery, use cracl_ing
_ _--_._.:.._-_J
the visor clip or screwdriver
hous_
blade to pry open the case as
shown. Insert battery matching
polarity instructions inside the
remote cover or on the printed circuit board.
limit and force adjustments Only
a screwdriver is required Follow
the instructions carefully
Repeat the safety reverse test (Adjustment Step 3,
page 29) after any adjustment of limits or force.
Dispose of old battery properly.
MAINTENANCE
SCHEDULE
Once a Month
NOTICE: To comply with FCC and or Industry Canada rules (iC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
• Manually operate door If it is unbalanced or binding,
call a trained door systems technician
Tested to Comply with ECC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
• Check to be sure door opens & closes fully Adjust limits
and/or force if necessary (See pages 27 and 28)
• Repeat the safety reverse test Make any necessary
adjustments (See Adjustment Step 3)
Twice a Year
• Check chain tension Disconnect trolley first Adjust if
necessary (See page 11)
Once a Year
• Oil door rollers, bearings and hinges The opener does
not require additional lubrication Do not grease the door
tracks
32
HAVING
A PROBLEM?
1. My door will not close and the light bulbs blink on
my motor unit: The safety reversing sensor must be
connected and aligned correctly before the garage door
opener will move in the down direction.
Bell Wire
• Verify the safety sensors are properly installed,
aligned and free of any obstructions. Refer to
Installation Step 10: Install The Protector Syster_.
• Check diagnostic LED for flashes on the motor unit
then refer to the Diagnostic Chart on the following
page.
2. My remotes will not activate the door:
• Reprogram remotes following the programming
instructions. Refer to Programming.
Safety Reversing Sensor
• If remote will still not activate your door, check
diagnostic LED for flashes on motor unit then refer to
Diagnostic Chart on the following page.
Sending Eye Safety Reversing
Sensor (Amber Indicator Light)
Receiving Eye Safety Reversing
Sensor (Green Indicator Light)
,/
3. My door reverses for no apparent reason: Repeat
safety reverse test after adjustments to force or travel
limits. The need for occasional adjustment for the force
and limit settings is normal. Weather conditions in
particular can affect door travel.
• Manually check door for balance or any binding
problems.
6. My motor unit hums briefly:
• First verify that the trolley is against the stop bolt.
• Refer to Adjustment Step 2, Adjust the Force.
• Release the door from the opener by pulling the
Emergency Release Rope.
4. My door reverses for no apparent reason after fully
closing and touching the floor: Repeat safety reverse
test after adjustments to force or travel limits. The need
for occasional adjustment for the force and limit settings
is normal. Weather conditions in particular can affect
door travel.
• Manually bring the door to a closed position.
• Loosen the chain by adjusting the outer nut 4 to 5
turns. This relieves the tension.
• Run the motor unit from the remote control or door
control. The trolley should travel towards the door and
stop. If the trolley re-engages with the door, pull the
Emergency Release Rope to disengage.
• Refer to Adjustment Step 1, Adjust the UP and DOWN
Travel Limits. Decrease down travel by turning down
limit adjustment screw clockwise.
• Decrease the UP travel by turning the UP Travel
adjustment screw 2 full turns away from the arrow.
• Re-tighten the outer nut so the chain is a 1/4" (6 mm)
above the base of the rail. (When the door is
reconnected and closed, the chain will sag. This is
normal.)
5. My lights will not turn off when door is open:
• The garage door opener is equipped with a security
light feature. This feature activates the light on when
the safety sensor beam has been obstructed.
• If the trolley does not move away from the bolt, repeat
the steps above.
33
Bell Wire
\
Installed
Safety Reversing Sensor
Diagnostic
Your garage door opener is programmed with
self-diagnostic capabilities. The "Learn" button/diagnostic
LED will flash a number of times then pause signifying it
has found a potential issue. Consult Diagnostic Chart below.
Chart
Safety reversing sensors
wire open (broken or
disconnected).
OR
Symptom: One or both of the Indicator lights on the safety sensors do
not glow steady.
• Inspect sensor wires for a short (staple in wire), correct wiring polarity (black/white
wires reversed), broken or disconnected wires, replace/attach
as needed.
• Disconnect all wires from back of motor unit.
• Remove sensors from brackets and shorten sensor wires to 1-2 ft (30-60 cm) from
back each of sensor.
Safety reversing sensors
wire shorted or
black/white wire
reversed.
• Reattach sending eye to motor unit using shortened wires. If sending eye indicator
light glows steadily, attach the receiving eye.
• Align sensors, if the indicator lights glow replace the wires for the sensors. If the
sensor indicator lights do not light, replace the safety sensors.
Symptom: LED is not fit on door control.
Door control or
wire shorted.
Safety reversing sensors
slightly misaligned
(dim or flashing LED).
Motor overheated or
possible RPM sensor
failure. Unplug to reset.
• Inspect door control/wires for a short (staple in wire), replace as needed.
• Disconnect wires at door control, touch wires together. If motor unit activates,
replace door control.
• If motor unit does not activate, disconnect door control wires from motor unit.
Momentarily short across red and white terminals with jumper wire. If motor unit
activates, replace door control wires.
Symptom: Sending indicator light glows steadily, receiving indicator light is
dim or flashing.
• Realign receiving eye sensor, clean lens and secure brackets.
• Verify door track is firmly secured to wall and does not move.
Symptom: Motor has overheated; the motor unit does not operate or
trolley is stuck on stop bolt = Motor unit hums briefly; RPM Sensor =
Short travel 6-8" (15-20 cm).
• Unplug unit to reset. Try to operate motor unit, check diagnostic code.
• If it is still flashing 5 times and motor unit moves 6-8" (15-20 cm), replace RPM
sensor.
• If motor unit doesn't operate, motor unit is overheated. Wait 30 minutes and retry. If
motor unit still will not operate replace logic board.
Motor Circuit Failure.
Replace Receiver
Logic Board.
Symptom: Motor unit doesn't operate.
• Replace logic board because motor rarely fails.
34
PROGRAMMING
NOTICE: If this Security.l_ garage door opener is operated with a non-rolling code transmitter, the technical measure in
the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The
owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code
transmitter to circumvent that technical measure.
Your garage door opener has already been programmed at the factory to operate with your hand-held remote control.
The door will open and close when you press the large push button.
Below are instructions for programming your opener to operate with additional Security÷ ® remote controls.
To Add
USING THE "LEARN"
or
Reprogram
a Hand.held
Remote
Control
BUTTON
To Erase
All
Codes From
Memory
Motor
To deactivate any unwanted remote, first
erase all codes:
Unit
_-_-L___®3__
i
Press and hold the "learn" button on motor
unit until the learn indicator light goes out
(approximately 6 seconds). All previous
codes are now erased. Reprogram each remote or keyless
entry you wish to use.
*3-Function
1. Press and release the "learn" button
on the motor unit. The learn
indicator light will glow steadily for
30 seconds.
Remotes
If provided with your garage door opener, the large button
is factory programmed to operate it. Additional buttons on
any Security÷ ®3-Function
remote or compact remote
_
._-'-_'_'_'_'_'_'_
can be programmed to
operate other Security÷ ®
garage door openers.
2. Within 30 seconds, press and hold
the button on the hand-held remote*
that you wish to operate your
garage door.
3. Release the button when the motor
unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.
35
To Add,
Reprogram
or
NOTE: Your new Keyless Entry must be programmed
USING THE "LEARN"
Change
a Keyless
Entry
PIN
to operate your garage door opener,
BUTTON
To set a temporary
PIN
You may authorize access by visitors or service people
with a temporary 4-digit PIN. After a programmed number
of hours or number of accesses, this temporary PIN
expires and will no longer open the door. It can be used to
close the door even after it has expired. To set a
temporary PIN:
)
1. Press the four buttons for your personal entry PIN (not
the last temporary PIN), then press and hold the _=
button.
The opener light will blink three times. Release the
button.
2. Press the temporary 4-digit PIN you have chosen, then
press Enter.
1. Press and release the "learn" button
on motor unit. The learn indicator
light will glow steadily for 30
seconds.
The opener light will blink four times.
3. To set the number of hours this temporary PIN will
work, press the number of hours (up to 255), then
press _.
2. Within 30 seconds, enter a four digit
personal identification number (PIN)
of your choice on the keypad. Then
press and hold the ENTER button.
OR
3. To set the number of times this temporary PIN will work,
press the number of times (up to 255), then press #.
The opener light will blink once when the temporary PIN
has been learned.
3. Release the button when the motor
unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.
To change an existing,
Test by pressing the four buttons for the temporary PIN,
then press Enter. The door should move. If the temporary
PIN was set to a certain number of openings, remember
that the test has used up one opening.To clear the
temporary password, repeat steps 1-3, setting the number
of hours or times to 0 in step 3.
known PIN
One Button Close: Opener can be closed by pressing
only the ENTER button if the one button close feature has
been activated. This feature has been activated at the
factory. To activate or deactivate this feature press and
hold buttons 1 and 9 for 10 seconds. The keypad will blink
twice when the one button close is active. The keypad will
blink four times when one button close is deactivated.
If the existing PIN is known, it may be changed by one
person without using a ladder.
1. Press the four buttons for the present PIN, then press
and hold the # button.
The opener light will blink twice. Release the # button.
2. Press the new 4-digit PIN you have chosen, then
press Enter.
The motor unit lights will blink once when the PIN has
been learned.
Test by pressing the new PIN, then press Enter. The door
should move.
36
REPAIR
Rail
PARTS
Assembly
Parts
3
6
KEY
NO.
PART
NO.
DESCRIPTION
1
4A1008
Master link kit
2
41C5141-1
Complete trolley assembly
3
41A5665-2
Complete rail
4
5
144C56
41A5807
Idler pulley
Chain and cable
6
12D598-1
"U" bracket
NOT SHOWN
183A163
Installation
Wear pads
Parts
\\
KEY
NO.
PART
NO.
DESCRIPTION
1
41 A4899
Standard control console
2
10A20
3V 2032 Lithium battery
3
41 A6140-3
3-function remote control housing
(no circuit board)
4
29B137
Visor clip
5
41A2828
Emergency release rope and handle
assembly
6
41A5047-2
7
41B4494-1
Header bracket w/clevis pin and fastener
2-Conductor bell wire: white and
white/red
8
41 A5047
9
178B35
Door bracket w/clevis pin and fastener
Curved door arm section
10
178B34
Straight door arm section
11
12B776
Hanging bracket
12
41 A5034
Safety sensor kit: receiving and sending
eyes with 3' (.9 m) 2-conductor
bell wire attached
13
41A5266-1
Safety sensor bracket
NOT SHOWN
41A5258-10
Installation hardware bag (includes
hardware listed on page 7)
Owner's manual
7
11
/
/
10
13
114A3392
37
Motor
Unit
Assembly
7
Parts
\
\
19
8
/
17
15
Brown
(Down)
Contact
Contact
KEY
NO.
PART
NO.
LIMIT SWITCH
ASSEMBLY
Contact
11
Wire
12
DESCRIPTION
KEY
NO.
PART
NO.
DESCRIPTION
1
41A5615
Chain Spreader
12
41 A5525-63
Cover
2
41 C4220A
Gear and sprocket assembly
Complete with: Spring washer,
thrust washer, retaining ring,
bearing plate, roll pins (2), drive
gear and worm gear, helical gear
w/retainer and grease
13
14
41 A2818
Limit switch drive & retainer
41 D3452
Limit switch assembly
41A2822-1
Interrupter cup assembly
41A2817
15
16
17
41 C4398A
RPM sensor assembly
41AC150-1
Receiver logic board assembly.
Complete with: Logic board,
end panel w/all labels, light
socket
4
41 B4245
Drive/worm gear kit w/grease,
roll pins (2)
Line cord
5
41 A5484-5
End panels w/all labels
18
6
4A1344
41 C5497
41 C5498
7
108D77
Light socket
Lens
High voltage wire harness
Low voltage wire harness
19
41D179
End panel w/all labels
8
30B532
Capacitor-
9
12A373
41A2826
10
41 A3150
Capacitor bracket
Terminal block w/screws
NOT SHOWN
Motor shaft bearing kit
11
41D3058
1/2 HP
41A2825
Universal replacement motor &
bracket assembly.'
Complete with: Motor, worm,
bracket, bearing assembly, RPM
sensor
38
Opener assembly hardware kit
(includes screws not
designated by a number in
illustration)
ACCESSORIES
139.53702
139.53753
Emergency Key Release:
Required for a garage with NO
access door. Enables homeowner to
open garage door manually from
outside by disengaging trolley.
139.53726
139.53752
To allow an 8 (2.4 m) foot door to
open fully.
Security+ ®Keyless Entry:
Enables homeowner to operate garage
door opener from outside by entering a 4
digit code on specially designed keypad.
139.53687
Premium Control
For finished ceilings or where
additional support is required, based
on garage construction. Includes
brackets and fastening hardware.
139.53709
Door Clearance Brackets:
(For Sectional Doors Only)
Console:
Provides a lock feature to prevent
operation of garage door from portable
remotes. A light feature controls the
opener lights. Can be used to program
the opener to accept additional remotes.
Support Brackets:
Extension Brackets:
(Available only through Sears
Parts & Service)
(Optional) For safety sensor
installation onto the wall or floor.
3-Function
139.53754
To allow a 10 (3 m) foot door to
open fully.
41A5281
Security+ ®Compact
Remote Control:
With loop for attaching key ring.
10 Foot (3 m) Rail Extension:
139.53589
Remote
Includes visor clip.
8 Foot (2.4 m)Rail Extension
139.53727
Secu rity-I.®3-Function
Control:
139.53749
Plug-In Light Control:
Enables homeowner to turn on a
lamp, television or other appliance
from car, bedside, or anywhere in the
home with a remote.
Replaces top brackets and rollers on
door to reduce height of door travel.
For use when installing opener in
garage with low headroom clearance.
WARRANTY
CRAFTSMAN
GARAGE
DOOR OPENER
90-DAY IN-HOME FULL WARRANTY
LIMITED WARRANTY
ON PRODUCT
For 90 days from the date of purchase, this product will be repaired, free of charge, if defective in material or workmanship.
ADDITIONAL
LIMITED WARRANTY
ON PARTS
From the 91st day up to 1 year from the date of purchase, replacement parts for any defective parts on this product will be furnished, free of
charge. You pay for labor.
ADDITIONAL
LIMITED WARRANTY
ON MOTOR
From the 91st day and through 4 years, if the motor on this product is defective, a replacement
for labor.
WARRANTY
RESTRICTION
motor will be furnished free of charge. You pay
This Craftsman Garage Door Opener Limited Warranty does not cover light bulbs or repair parts necessary because of operator abuse or
negligence, including the failure to install, adjust and operate this garage door opener according to instructions contained in the owner's manual.
This limited warranty also does not cover any problems caused by interference.
LIMITATION
ON LIABILITY
Seller will not be liable for loss or damage to property or any incidental or consequential loss or expense from property damage due directly or
indirectly to the use of this product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
DISCLAIMER
OF IMPLIED
WARRANTIES
Except for the motor, all implied warranties for this product, including but not limited to any implied warranties of merchantability and fitness for a
particular purpose, are limited in duration to the 91st day through 1-year limited warranty period set forth above. All implied warranties with
respect to the motor are limited in duration to the 91st day through 4-year limited warranty period set forth above. No implied warranties will exist
or apply after such periods. Some States do not allow limitations on how long an implied warranty lasts, so the above limitations may not
apply to you.
WARRANTY
SERVICE
IS AVAILABLE
BY CALLING
1-800-4-MY-HOME
®.
This warranty applies only while this product is in use in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
39