Toro Rake and Vac (51574) Sell Sheet

Rake-O-Vac
®
f
e
a t
u
r
e
s
•2
3 hp (17.2 kW) Kohler Command Pro
engine
®
®
• 4.75 cubic yard (3.6 cubic meter) capacity
A clean sweep.
The Rake-O-Vac’s Kohler 23 hp engine insures there is plenty of
®
horsepower to clean debris from the most difficult turf. A spring-loaded
flex tip reel provides exceptional sweeping performance especially
with those annoying pine needles. The large 4.75 cubic yard hopper
provides plenty of capacity for picking up large areas. Compact and
maneuverable, the Toro Rake-O-Vac clears debris from even the
tightest areas. The rugged impeller fan pulverizes leaves and
debris saving space in the hopper yet the airflow in the
hopper minimizes dust by directing it back to the ground
keeping your neighbors happy.
•N
ew airflow
system delivers a
cleaner sweeping
environment
• S pring-Loaded Flex Tip Reel –
Flexible nylon fingers brush the ground
clear of debris utilizing a spring-loaded
design to give the fingers an extra kick
for clearing debris in wet conditions
•O
ptional Broom Reel provides
additional sweeping power
©2013 The Toro Company
All rights reserved.
8111 Lyndale Ave. S.
Bloomington, MN 55420-1196
Printed in the U.S.A. Rev. 2/13
Call your Toro distributor at 1-800-803-8676
Rake-O-Vac Specifications*
®
RAKE-O-VAC ENGINE DRIVE, MODEL 07055
POWER SUPPLy
Kohler Command Pro CH680, 23 hp (17.2 kW) @ 3600 rpm, 4 cycle, air-cooled, V-twin cylinders, horizontal crankshaft with a 5.5" (14 cm) dry centrifugal clutch.
Compression ratio: 8.5:1. Overhead placement valves; intake, forged high carbon steel, exhaust Stellite faced. Hydraulic valve lifters. Full pressure 4 pint (2.3
liter) with filter, oil capacity. 12-volt, 15 amp alternator with solid state regulator/rectifier. Solid state electronic ignition system with electronically controlled spark
advance. Tri-phase design with screen pre-cleaner, replaceable filter cartridge and dump valve.
FAN IMPELLER
Centrifugal type housing, double inlet. Four alloy steel blades, 16" (41 cm) wide x 23.25" (59 cm) diameter, .1875" (4.8 mm) thick. High tensile, .5625" (4 cm) stress-proof steel shaft mounted
in self-aligning sealed ball bearings. Blower discharge area: 255 in (1645 cm ).
®
DRIVE
FAN HOOD
REEL/BRUSH DRIVE
MAIN FRAME
WHEELS AND TIRES
HOPPER
HITCH
FLEX TIP REEL
DIMENSIONS
WEIGHT
WARRanty
®
®
2
2
Banded double. B-80 drive belt direct from drive shaft to fan impeller drive shaft. Fan impeller runs at 1580 rpm [tip speed 9,720 ft/min. (2963 m/min.)] at 3250
engine rpm.
Twin construction for uniform air distribution; 4.5" (11.4 cm) deep x 63" (160 cm) wide. Inlet area: 283 in (1826 cm ).
Variable position, front weighted rubber flap.
2
2
Belted-double B-53 drive belt from engine to jack shaft. Banded (4) 3V cross section belt, from jack shaft to flex tip reel.
Flex tip reel runs at 275 rpm [tip speed 1,355 ft./min. (413 m/min.)] at 3250 engine rpm.
All welded, structural, rectangular, 2" x 4" (5 cm x 10 cm) and 4" x 4" (10 cm x 10 cm), 11-gauge, steel tubing.
High flotation type I-1 rib tread, 11L-14SL, 6 ply rating, tubeless construction mounted on 8" (20 cm) x 14" (36 cm) wheel with six bolt attachment. Inflation
pressure 28 psi (1.9 bar).
4.75 cu. yd. (3.6 m ) volume; 18-gauge top section with 16-gauge bottom section - rib reinforced; full width, self-cleaning,
semi-automatic dumping.
3
Pin type, .75" (1.9 cm) diameter; adjustable vertical height for tractor hitches from 7.25" (18.4 cm) to 17.25" (43.8 cm) height.
Forward sweeping, 6 rows of teeth, all steel construction with replaceable .1875" (4.8 mm) extruded nylon teeth; each row containing 11 individually spring
loaded flexible sets, 552 total teeth, 18.75" (48 cm) diameter reel, 61" (155 cm) wide, 1.125"
(2.9 cm) diameter shaft set in self aligning sealed bearings. Reel supported by adjustable counterbalance springs and adjustable-gauge wheels. Gauge wheels
aluminum construction with non-scuffing rubber tires operating on greaseable ball bearings;
infinitely adjustable vertically.
Width HeightLength
85.5" (217 cm)
79.5" (202 cm)
13'3" (4.0 m)
2,980 lbs. (1,355 kg)
Two-year limited warranty. Refer to the Operator’s Manual for further details.
OPTIONAL EQUIPMENT
BRUSH
Forward sweeping continuous, polypropylene bristle, floating action provided by spring counterbalance and gauge wheel height adjustment. Model 07162.
Brush speed: 275 rpm [tip speed 1,370 ft./min. (417 m/min.)] at 3200 engine rpm.
*Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor.
“Stellite” is a trademark of Stoody Deloro Stellite, Inc.