TP-Link TL-R480T+ V5 Installation Guide

Enterprise Networking Solution
Installation Guide
Load Balance Broadband Router
TL-R480T+
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice.
is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their
respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
111
This device may not cause harmful interference.
222
This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
I
Copyright & Trademarks
Related Document
The User Guide of this product is provided in the resource CD. To obtain the latest
product information, please visit the Official Website:
http://www.tp-link.com
About this Installation Guide
This Installation Guide describes the hardware characteristics, installation methods
and the points that should be attended to during installation. This Installation
Guide is structured as follows:
Chapter 1 Introduction. This chapter describes the External Components of
the Router.
Chapter 2 Installation. This chapter illustrates how to install the Router.
Chapter 3 Lightning Protection. This chapter illustrates how to prevent
lightning damage.
Chapter 4 Connection. This chapter illustrates how to do the physical connection of the Router.
Chapter 5 Configuration. This chapter illustrates how to login and set up the
Router.
Appendix A Troubleshooting.
Appendix B Hardware Specifications.
Appendix C Technical Support.
Audience
This Installation Guide is for:
Network Engineer
Network Administrator
Conventions
This Guide uses the specific formats to highlight special messages. The following
table lists the notice icons that are used throughout this guide.
Remind to be careful. A caution indicates a potential which may result in
device damage.
Remind to take notice. The note contains the helpful information for a
better use of the product.
Related Document
II
Contents
Chapter 1
Introduction ——————————— 01
1.1
Product Overview ...................................................................01
1.2
Appearance ...............................................................................01
Chapter 2
2.1
Installation ———————————— 03
Package Contents ...................................................................03
2.2
Safety Precautions ..................................................................03
2.3
Installation Tools......................................................................05
2.4
Product Installation ................................................................06
Chapter 3
Lightning Protection ———————— 08
3.1
Cabling Reasonably................................................................08
3.2
Connect to Ground.................................................................10
3.3
Equipotential Bonding ..........................................................11
3.4
Use Lightning Arrester ..........................................................12
Chapter 4
Connection ——————————— 14
4.1
WAN Port ....................................................................................14
4.2
LAN Port .....................................................................................14
4.3
Console Port..............................................................................14
4.4
Verify Installation ....................................................................15
4.5
Power On....................................................................................15
4.6
Initialization ..............................................................................15
Chapter 5
Configuration——————————— 16
5.1
Preparations ..............................................................................16
5.2
Login ............................................................................................16
Appendix A Troubleshooting ————————— 20
Appendix B Hardware Specifications —————— 21
Appendix C Technical Support ————————— 22
III
Contents
Load Balance Broadband Router
CCCCCCCCCC Introduction
1111
Product Overview
TL-R480T+ is a product designed for small business. It features three free changeable
ports that can be set to either LAN or WAN, allowing the router to support up to four
WAN ports to satisfy various Internet access requirements through one device. At the
same time, network traffic is managed to ensure that data is properly distributed to
each port. TP-LINK TL-R480T+ will provide you consistent network uptime and reliable
Ethernet connectivity.
1111 Appearance
■■
Front Panel
The front panel of TL-R480T+ is shown as the following figure.
FFFFFFFFFFF Front Panel
LEDs
LED
PWR
SYS
Link/Act
100Mbps
Status
Indication
On
The Router is powered on
Off
The Router is powered off or power supply is abnormal
Flashing
The Router works properly
On/Off
The Router works improperly
On
(Green/Yellow1
There is a device linked to the corresponding port but
not active
(Green indicates the corresponding port is working as
a LAN port, and yellow indicates WAN port1
Flashing
(Green/Yellow1
The corresponding port is transmitting or receiving
data
(Green indicates the corresponding port is working as
a LAN port, and yellow indicates WAN port1
Off
There is no device linked to the corresponding port
On
(Green/Yellow1
The linked device is running at 100Mbps
(Green indicates the corresponding port is working as
a LAN port, and yellow indicates WAN port1
Off
There is no device linked to the corresponding port or
the port is running at 10Mbps
Introduction
01
Load Balance Broadband Router
Interface Description
Interface
Description
WAN
The WAN port is designed to connect the Router to the interface provided
by ISP via the RJ45 cable
LAN
The LAN port is designed to connect the Router to the local PCs or
switches by the RJ45 cable
Console
The Console port is designed to connect with the serial port of a computer
or terminal to check and monitor some simple system information of the
Router
Reset
With the Router powered on, use a pin to press and hold the Reset button (about 5
seconds) until the SYS LED flashes quickly. Then release the button and wait for the
Router rebooting to its factory default settings.
■■
Rear Panel
The rear panel of TL-R480T+ is shown as the following figure.
FFFFFFFFFFF Rear Panel
Power Socket
Connect the female connector of the power cord here, and the male connector to
the AC power outlet. Please make sure the voltage of the power supply meets the
requirement of the input voltage.
Grounding Terminal
The Router already comes with lightning protection mechanism. You can also ground
the Router through the PE (Protecting Earth) cable of AC cord or with Ground Cable.
For detailed information, please refer to Chapter 3 Lightning Protection.
Caution: Please use the provided power cord.
02
Introduction
Load Balance Broadband Router
CCCCCCCCCC Installation
2222 Package Contents
Make sure that the package contains the following items. If any of the listed items is
damaged or missing, please contact your distributor.
One Router
One Power Cord, One Console
Cable and One Ethernet Cable
One Resource CD
Two mounting brackets and the
fittings
This Installation Guide
2222 Safety Precautions
To avoid any device damage and bodily injury caused by improper use, please observe
the following rules.
■■
Safety Precautions
■■
Keep the power off during the installation.
■■
■■
■■
Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good
skin contact and is well grounded.
Use only the power cord provided with the Router.
Make sure that the supply voltage matches the specifications indicated on the rear
panel of the Router.
■■
Ensure the vent hole is well ventilated and unblocked.
■■
Do not open or remove the cover of the Router.
■■
Before cleaning the device, cut off the power supply. Do not clean it by the waterish
cloth, and never use any other liquid cleaning method.
Installation
03
Load Balance Broadband Router
■■
Site Requirements
Temperature/Humidity
ȭ
ȭ
Please keep a proper temperature and humidity in the equipment room. Too high/low
humidity may lead to bad insulation, electricity leakage, mechanical property changes
and corrosions. Too high temperature may accelerate aging of the insulation materials
and can thus significantly shorten the service life of the device. For normal temperature
and humidity of the device, please check the following table.
Environment
Temperature
Humidity
Operating
0℃ ~ 40℃
10% ~ 90%RH Non-condensing
Storage
-40℃ ~ 70℃
5% ~ 90%RH Non-condensing
Clearness
The dust accumulated on the Router can be absorbed by static electricity and result
in poor contact of metal contact points. Some measures have been taken for the
device to prevent static electricity, but too strong static electricity can cause deadly
damage to the electronic elements on the internal circuit board. To avoid the effect of
static electricity on the operation of the Router, please attach much importance to the
following items:
■■
Dust the device regularly, and keep the indoor air clean.
■■
Keep the device well grounded and ensure static electricity has been transferred.
Electromagnetic Interference
Electronic elements including capacitance and inductance on the device can be affected
by external interferences, such as conducted emission by capacitance coupling,
inductance coupling, and impedance coupling. To decrease the interferences, please
make sure to take the following measures:
■■
■■
■■
04
Installation
Use the power supply that can effectively filter interference from the power grid.
Keep the device far from high-frequency, strong-current devices, such as radio
transmitting station.
Use electromagnetic shielding when necessary.
Load Balance Broadband Router
Lightening Protection
Extremely high voltage currents can be produced instantly when lightning occurs and the air
in the electric discharge path can be instantly heated up to 20,000℃. As this instant current
is strong enough to damage electronic devices, more effective lightning protection measures
should be taken.
■■
Ensure the rack and device are well earthed.
■■
Make sure the power socket has a good contact with the ground.
■■
Keep a reasonable cabling system and avoid induced lightning.
■■
Use the signal SPD (Surge Protective Device) when wiring outdoor.
Note: For detailed lightning protection measures, please refer to Chapter 3
Lightning Protection.
Installation Site
S
When installing the device on a rack or a flat workbench, please note the following
items:
■■
■■
■■
The rack or workbench is flat and stable, and sturdy enough to support the weight
of 5.5kg at least.
The rack or workbench has a good ventilation system. The equipment room is well
ventilated.
The rack is well grounded. Keep the power socket less than 1.5 meters away from
the device.
2222 Installation Tools
■■
Phillips screwdriver
■■
ESD-preventive wrist wrap
■■
Cables
Installation
05
Load Balance Broadband Router
Note: These tools are not provided with our product. If needed, please self purchase
them.
2222 Product Installation
■■
Desktop Installation
To install the device on the desktop, please follow the steps:
111Set the device on a flat surface strong enough to support the entire weight of the
device with all fittings.
222Remove the adhesive backing papers from the rubber feet.
333Turnover the device and attach the supplied rubber feet to the recessed areas on
the bottom at each corner of the device.
Feet
Bottom of the Device
Notch
FFFFFFFFFFF Desktop Installation
■■
Rack Installation
To install the device in an EIA standard-sized, 19-inch rack, follow the instructions
described below:
111Check the grounding and stability of the rack.
222Secure the supplied rack-mounting brackets to each side of the device with supplied
screws, as illustrated in the following figure.
Rackmounting Bracket
Screw
FFFFFFFFFFF Bracket Installation
06
Installation
Load Balance Broadband Router
333After the brackets are attached to the device, use suitable screws (not provided) to
secure the brackets to the rack, as illustrated in the following figure.
Rack
FFFFFFFFFFF Rack Installation
Caution:
Please set 5~10cm gaps around the device for air circulation.
Please avoid any heavy thing placed on the device.
Please mount devices in sequence from the bottom to top of the rack and ensure a
certain clearance between devices for the purpose of heat dissipation.
■■
■■
■■
Installation
07
Load Balance Broadband Router
CCCCCCCCCC Lightning Protection
3333 Cabling Reasonably
In the actual network environment, you may need cable outdoors and indoors, and
the requirements for cabling outdoors and indoors are different. A reasonable cabling
system can decrease the damage of induced lightning to devices.
Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors,
please use a signal lightning arrester.
■■
Requirements for Cabling Outdoors
■■
Aerial cabling without safeguard is not allowed.
■■
■■
■■
■■
08
It’s not allowed cabling down the building to connect network devices in different
floors.
Outdoor cables should be buried and paved to the indoor through basement. A
piece of steel wire should be paved underground along the pipe and connected to
the lightning protection terminal of the building for shielding. Before connecting the
cable to the device, install a signal lightning arrester on the corresponding port.
When an aerial cable is set up, the cable should be through a metal pipe (15m long
at least) before coming into the building. The two ends of this metal pipe should
be grounded. Before connecting the cable to the device, install a signal lightning
arrester on the corresponding port.
It’s not necessary to pave STP cables through pipes. The shielded layer of STP cable
should be well grounded. Before connecting the cable to the device, install a signal
lightning arrester on the corresponding port.
Lightning Protection
Load Balance Broadband Router
■■
Requirements for Cabling Indoors
When cabling indoors, keep a certain distance away from the devices that may cause
high-frequency interferences, such as down-conductor cable, powerline, power
transformer and electromotor.
■■
■■
The main cable should be paved in the metal raceway of the access shaft. When
cabling, keep the loop area formed by the cable itself as small as possible.
Requirements for the distance between Ethernet cable and other pipelines are
shown in the table.
Ethernet Cable
Other Pipelines
Min Parallel Net Length L
(mm1
Min Parallel-overlapping
Net Height H (mm1
Down-conductor
1000
300
PE
50
20
Service pipe
150
20
Compressed air pipe
150
20
Thermal pipe (not wrapped1
500
500
Thermal pipe (wrapped1
300
300
Gas pipe
300
20
The two diagrams below demonstrate parallel net length and parallel-overlapping net
height.
Note: The above minimum net length/height is required when metal raceway is not
used. If any requirements cannot be met, you can add a steel tube or metal raceway
for shielding.
■■
Requirements for the distance between Ethernet cable and high-power electric
devices are in following tables.
Cable
<2kVA
powerline
Pave Way
Min Parallel
Length (mm1
Parallel cabling
130
One is in the grounded metal raceway or metal pipe
70
The both are in the grounded metal raceway or metal
pipe
10
Lightning Protection
09
Load Balance Broadband Router
2~5kVA
powerline
>5kVA
powerline
Parallel cabling
300
One is in the grounded metal raceway or metal pipe
150
The both are in the grounded metal raceway or metal
pipe
80
Parallel cabling
600
One is in the grounded metal raceway or metal pipe
300
The both are in the grounded metal raceway or metal
pipe
150
Device
Min Distance (m1
Switch case
1.00
Transformer room
2.00
Elevator tower
2.00
Air-conditioner room
2.00
3333 Connect to Ground
Connecting the device to ground is to quickly release the lightning over-voltage and
over-current of the device, which is also a necessary measure to protect the body from
electric shock.
In different environments, the device may be grounded differently. The following
will instruct you to connect the device to the ground in two ways, connecting to the
grounding bar or connecting to the ground via the power cord. Please connect the
device to ground in the optimum way according to your specific operation environment.
■■
Connecting to the Grounding Bar
If the device is installed in the Equipment Room, where a grounding bar is available,
you are recommended to connect the device to the grounding bar as shown in the
following figure.
Device (Rear Panel)
Grounding Terminal
Ground Cable
Grounding Bar
FFFFFFFFFFF Connecting to the Grounding Bar
10
Lightning Protection
Load Balance Broadband Router
Note: The grounding bar and the ground cable are not provided with our product. If
needed, please self purchase them.
■■
Connecting to the Ground via the Power Supply
If the device is installed in the normal environment, the device can be grounded via the
PE (Protecting Earth) cable of the AC power supply as shown in the following figure.
FFFFFFFFFFF Connecting to the Ground
Note:
The figure is to illustrate the application and principle. The power plug you get from
the package and the socket in your situation will comply with the regulation in your
country, so they may differ from the figure above.
If you intend to connect the device to the ground via the PE (Protecting Earth) cable
of AC power cord, please make sure the PE (Protecting Earth) cable in the electrical
outlet is well grounded in advance.
■■
■■
3333 Equipotential Bonding
Equipotential Bonding is the practice of intentionally electrically connecting all earthed
systems to the same grounding grid or connecting the grounding grids of all the
earthed systems together through the ground or overground metal so as to create
an earthed equipotential zone. When lightning occurs, the high voltage produced by
lightning current in all systems will meanwhile exist in their ground cables, and thus
all ground cables have the same electrical potential and basically eliminate the electric
strikes between the systems.
The figure bellow illustrates how to practice equipotential bonding in a network.
Lightning Protection
11
Load Balance Broadband Router
Grounding Terminal
Equipotential Bonding Cable
Ground Cable
Grounding Bar
FFFFFFFFFFF Equipotential Bonding
When equipotential bonding, please note that the cable should be copper wrapped
2
Kelly with its area being 6mm at least. The shorter cable the better, and use a
grounding bar to establish an equipotential bonding point.
Note: The equipotential bonding cable is not provided with our product. If needed,
please self purchase it.
3333 Use Lightning Arrester
Power lightning arrester and signal lightning arrester are used for lighting protection.
Power lightning arrester is used for limiting the voltage surge due to a lightning. If an
outdoor AC power cord should be directly connected to the device, please use a power
lightning arrester.
Note: Power lightning arrester is not provided with our product. If needed, please self
purchase it.
12
Lightning Protection
Load Balance Broadband Router
Signal lightning arrester is used to protect RJ45 ports of the device from lightning.
When cabling outdoors, please install a signal lightning arrester before connecting the
cable to the device.
When purchasing or using a signal lightning arrester, please observe the following
rules:
■■
■■
The port rate of the signal lightning arrester should match the rate of the desired
port on the device. If it is not matched, this signal lighting arrester will not work.
Purchase a standard lightning arrester.
Install signal lightning arrester near the protected device and connect it to the
ground via a shorter ground cable.
Grounding Terminal
Equipotential Bonding Cable
Signal Lightning Arrester
Device
Ethernet Cable
FFFFFFFFFFF Equipotential Bonding
Note: Signal lightning arrester is not provided with our product. If needed, please self
purchase it.
Lightning Protection
13
Load Balance Broadband Router
CCCCCCCCCC Connection
4444 WAN Port
Please connect the WAN port of the Router to the interface provided by ISP via
Ethernet cable.
4444 LAN Port
Connect a LAN port of the Router to the computer by RJ45 cable as the following figure
shown.
LAN Port
RJ45 Cable
RJ45 Port
FFFFFFFFFFF Connecting the LAN Port
4444 Console Port
CLI (Command Line Interface) enables you to do some simple operations to the Router,
thus you can load the CLI after connecting the PCs or Terminals to the console port on
the Router via the provided cable. For TL-R480T+, you can check and monitor some
simple system information of the Router.
Connect the console port of the device with your computer by the console cable as the
following figure shown.
FFFFFFFFFFF Connecting the Console Port
14
Connection
Load Balance Broadband Router
Note:
The console port is the first port on the right of the front panel.
Please keep the device power off when you plugging the console cable.
Do not connect the console port with other ports by RJ45 cable.
■■
■■
■■
4444 Verify Installation
After completing the installation, please verify the following items:
■■
There are 5~10cm of clearance around the sides of the device for ventilation and
the air flow is adequate.
■■
The voltage of the power supply meets the requirement of the input voltage of the device.
■■
The power socket, device and rack are well grounded.
■■
The device is correctly connected to other network devices.
4444 Power On
Plug in the negative connector of the provided power cord into the power socket of the
device, and the positive connector into a power outlet as the following figure shown.
FFFFFFFFFFF Connecting to Power Supply
Note: The figure is to illustrate the application and principle. The power plug you get
from the package and the socket in your situation will comply with the regulation in
your country, so they may differ from the figure above.
4444 Initialization
After the device is powered on, it begins the Power-On Self-Test. A series of tests run
automatically to ensure the device functions properly. During this time, its LED indicators will respond as follows:
■■
The Power LED lights on all the time.
■■
All LEDs except PWR LED flashes momentarily and then turns off.
■■
The SYS LED flashes every second continuously, which means the initialization is finished.
Connection
15
Load Balance Broadband Router
CCCCCCCCCC Configuration
5555 Preparations
111Connect a PC to a LAN port of the Router with a RJ45 cable properly.
222Set the Internet Protocol (TCP/IP) properties of the PC with the "IP address" as
192.168.0.x ("x" is any number from 2 to 254), "Subnetmask" as 255.255.255.0 and
"Default gateway" as 192.168.0.1. Shown in the following figure.
FFFFFFFFFFF Internet Protocol (TCP/IP) Properties
5555 Login
111To access the GUI (Graphical User Interface) of the Router, open a web browser and
type the default management address http://192.168.0.1 in the address field of the
browser, then press the Enter key.
FFFFFFFFFFF Web Browser
222Enter "admin" for the default User name and Password, both in lower case letters.
Then click the OK button or press the Enter key.
FFFFFFFFFFF Login
16
Configuration
Load Balance Broadband Router
333After a successful login, the Quick Setup screen will pop up as the Figure 5-4
shown. If it does not prompt, you can click the Quick Setup on the left of the main
menu. Then click Next.
FFFFFFFFFFF Quick Setup
444Select the total number of WAN ports you prefer to use as the Figure 5-5 shown.
Then click Next to load the WAN Port screen.
FFFFFFFFFFF WAN Mode
555Select the WAN port you want to use as the Figure 5-6 shown, and then click Next
to load the WAN Connection Type screen.
FFFFFFFFFFF WAN Port
666Select the connection type provided by your ISP (Internet Service Provider) as the
Figure 5-7 shown. Three popular types are provided here. For other connection
types, please refer to the Network→WAN.
FFFFFFFFFFF WAN Connection Type
1)If you choose PPPoE, you will see the screen as the Figure 5-8 shown. Enter the
Account Name and Password provided by your ISP.
Configuration
17
Load Balance Broadband Router
FFFFFFFFFFF WAN Connection Type - PPPoE
Click Next to dial up, and the process will take a few minutes. The process of
configuring the network parameters is shown as Figure 5-9. If you close the screen
during the process, the configuration will still be continued in the background.
These fields are case sensitive. If you have difficulty in this process, please contact
your ISP.
FFFFFFFFFFF WAN Connection Type – PPPoE Connecting
2)If your ISP assigns the IP address automatically, please choose the Dynamic IP
connection type to obtain the parameters for WAN port automatically. The process
for obtain the parameter may take a few minutes as Figure 5-10 shown. If you
close the screen during the process, the configuration will still be continued in the
background.
FFFFFFFFFFFFWAN Connection Type - Dynamic IP
3)If you choose Static IP, you should enter the detailed IP information provided by
your ISP in Figure 5-11.
FFFFFFFFFFFFWAN Connection Type - Static IP
Then click Next. The process for configuring the network parameters is shown as
Figure 5-12. If you close the screen during the process, the configuration will still be
continued in the background.
18
Configuration
Load Balance Broadband Router
If you have difficulty in this process, please contact your ISP.
FFFFFFFFFFFFWAN Connection Type - Static IP Connecting
777 After that, you will see the next screen. Click Finish to complete the quick
installation or click Continue to configure other WAN ports.
FFFFFFFFFFFFConfiguration Completed
888After a successful login, the main page will appear as the following figure, and you
can configure the function by clicking the setup menu on the left side of the screen.
FFFFFFFFFFFF Main Page of the Router
Configuration
19
Load Balance Broadband Router
Appendix A Troubleshooting
QQQQ What could I do if I forgot the username and password of the
Router?
You can restore the Router to factory defaults, please refer to 1.2
Appearance of this Installation Guide for detail. The default management
address of the Router is http://192.168.0.1, default username and password
are both admin. All your current settings will be cleared after the Router is
restored. If you have backup configuration, please import it now.
QQQQ Why does the PWR LED work abnormally?
The PWR LED should be lit up when the power system works normally. If the
PWR LED worked abnormally, please check as follows:
111 Make sure that the power cable is connected properly, and the power
contact is normal.
222 Make sure the voltage of the power supply meets the requirement of the
input voltage of the Router.
QQQQ What could I do if I could not access the web-based configuration
page?
You are recommended to check the following items:
111 Check every port LED on the Router and make sure the cable is installed
properly.
222 Try another port on the Router and make sure the cable meets the
requirement and works normally.
333 Turn off the power. After a while, turn on the power again.
444 Make sure the IP address of your PC is set within the subnet of the
Router.
555 If you still cannot access the configuration page, please restore the
Router to its factory defaults. Then the IP address should be set as
192.168.0.x (“x” is any number from 2 to 254) and Subnet Mask as
255.255.255.0.
QQQQ Why does the page display abnormally?
Please check as follows:
111 Update your browser or replace it with another browser, and try again.
222 If the pop-up is blocked, please lower the security level of the browser.
20
Troubleshooting
Load Balance Broadband Router
Appendix B Hardware Specifications
Item
Content
Standards and Protocol IEEE 802.3, IEEE 802.3u,
TCP/ IP, DHCP, ICMP, NAT, PPPoE, SNTP, HTTP, DNS
Transmission Medium
10Base-T: UTP/STP of Cat. 3 or above
100Base-TX: UTP/STP of Cat. 5 or above
LEDs
PWR, SYS, Link/Act, 100Mbps
Operating Temperature 0℃~40℃
Storage Temperature
-40℃~70℃
Operating Humidity
10%~90%RH Non-condensing
Storage Humidity
5%~90%RH Non-condensing
Size (L×W×H1
294mm×180mm×44mm
Hardware Specifications
21
Load Balance Broadband Router
Appendix C Technical Support
■■
■■
For more help, please go to: www.tp-link.com/support/faq.asp
To download the latest Firmware, Driver, Utility and User Guide, please go to:
www.tp-link.com/support/download.asp
■■
22
For all other technical support, please contact us by using the following details:
Global
Tel: +86 755 26504400
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Singapore
Tel: +65 62840493
E-mail: [email protected]
Service time: 24hrs, 7 days a week
UK
Tel: +44 (01 845 147 0017
E-mail: [email protected]
Service time: 24hrs, 7 days a week
USA/Canada
Toll Free: +1 866 225 8139
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Australia & New Zealand
Tel: AU 1300 87 5465 NZ 0800 87 5465
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Malaysia
Tel: 1300 88 875465 (1300 88TPLINK1
Email: [email protected]
Service time: 24hrs, 7 days a week
Turkey
Tel: 444 19 25 (Turkish Service1
E-mail: [email protected]
Service time: 9:00 AM to 6:00 PM, 7 days a week
Italy
Tel: +39 02 66987799
E-mail: [email protected]
Service time: Monday to Friday, 9:00 AM to 6:00 PM
Ukrainian
Tel: +380 (441 590-51-14
E-mail: [email protected]
Service time: Monday to Friday, 14:00 PM to 22:00 PM
Brazilian
Toll Free: 0800-770-4337 (Portuguese Service1
E-mail: [email protected]
Service time: Monday to Saturday, 08:00 AM to 08:00 PM
Poland
Tel: +48 (01 801 080 618 / +48 22 7217563 (if calls from mobile phone1
E-mail: [email protected]
Service time: Monday to Friday 9:00 AM to 5:00 PM. GMT+1 or GMT+2
(Daylight Saving Time1
Russian Federation
Tel: 8 (4951 223-55-60
8 (8001 250-55-60 (toll-free call from any RF region1
E-mail: [email protected]
Service time: From 10:00 to 18:00 (Moscow time1
*Except weekends and holidays in Russian Federation
Indonesia
Tel: (+62 1 021 6259 135
E-mail: [email protected]
Service time: Monday to Friday, 9:00-12:00 ; 13:00-18:00
*Except public holidays
Technical Support
Load Balance Broadband Router
Germany/Austria
Tel: +49 1805 875465 (German Service1/+49 1805 TPLINK
E-mail: [email protected]
Fee: 0.14 EUR/min from the German fixed phone network and up to 0.42
EUR/min from mobile phone
Service time: Monday to Friday 9:00 AM to 6:00 PM
GMT+ 1 or GMT+ 2 (Daylight Saving Time in Germany1
*Except bank holidays in Hesse
Switzerland
Tel: +41 (01848 800998 (German Service1
E-mail: [email protected]
Fee: 4-8 Rp/min, depending on rate of different time
Service time: Monday to Friday 9:00 AM to 6:00 PM,
GMT+ 1 or GMT+ 2 (Daylight Saving Time1
Technical Support
23
Website: http://www.tp-link.com
E-mail: [email protected]
7106503825
Rev: 2.0.0