TP-Link TL-SG2210P User Guide

Add to my manuals
188 Pages

advertisement

TP-Link TL-SG2210P User Guide | Manualzz

TL-SG2210P/TL-SG2216/TL-SG2424/

TL-SG2424P/TL-SG2452

Gigabit Smart Switch

REV1.3.0

1910011016

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK

TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами

України.

III

Safety Information

 When product has power button, the power button is one of the way to shut off the product;

When there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

This product can be used in the following countries:

AT BG BY CA CZ DE DK EE

ES FI FR GB GR HU IE IT

LT LV MT NL NO PL PT RO

RU SE SK TR UA US

IV

CONTENTS

Package Contents ..........................................................................................................................1

Chapter 1 About this Guide...........................................................................................................2

1.1 Intended Readers .........................................................................................................2

1.2 Conventions..................................................................................................................2

1.3 Overview of This Guide ................................................................................................2

Chapter 2 Introduction ..................................................................................................................6

2.1 Overview of the Switch .................................................................................................6

2.2 Main Features...............................................................................................................6

2.3 Appearance Description ...............................................................................................6

2.3.1 Front Panel ........................................................................................................6

2.3.2 Rear Panel .......................................................................................................10

Chapter 3 Login to the Switch.....................................................................................................12

3.1 Login...........................................................................................................................12

3.2 Configuration ..............................................................................................................12

Chapter 4 System .......................................................................................................................14

4.1 System Info.................................................................................................................14

4.1.1 System Summary.............................................................................................14

4.1.2 Device Description ...........................................................................................15

4.1.3 System Time ....................................................................................................16

4.1.4 Daylight Saving Time .......................................................................................17

4.1.5 System IP.........................................................................................................18

4.2 User Management ......................................................................................................19

4.2.1 User Table........................................................................................................19

4.2.2 User Config ......................................................................................................20

4.3 System Tools ..............................................................................................................21

4.3.1 Config Restore .................................................................................................21

4.3.2 Config Backup..................................................................................................22

4.3.3 Firmware Upgrade ...........................................................................................22

4.3.4 System Reboot ................................................................................................23

4.3.5 System Reset...................................................................................................23

4.4 Access Security ..........................................................................................................24

4.4.1 Access Control.................................................................................................24

4.4.2 SSL Config.......................................................................................................25

4.4.3 SSH Config ......................................................................................................27

Chapter 5 Switching....................................................................................................................33

5.1 Port .............................................................................................................................33

III

5.1.1 Port Config .......................................................................................................33

5.1.2 Port Mirror ........................................................................................................34

5.1.3 Port Security ....................................................................................................36

5.1.4 Port Isolation ....................................................................................................38

5.1.5 Loopback Detection .........................................................................................39

5.2 LAG ............................................................................................................................40

5.2.1 LAG Table ........................................................................................................41

5.2.2 Static LAG ........................................................................................................42

5.2.3 LACP Config ....................................................................................................43

5.3 Traffic Monitor .............................................................................................................45

5.3.1 Traffic Summary...............................................................................................45

5.3.2 Traffic Statistics ................................................................................................46

5.4 MAC Address..............................................................................................................47

5.4.1 Address Table ..................................................................................................48

5.4.2 Static Address ..................................................................................................49

5.4.3 Dynamic Address .............................................................................................50

5.4.4 Filtering Address ..............................................................................................52

5.5 DHCP Filtering............................................................................................................53

Chapter 6 VLAN..........................................................................................................................57

6.1 802.1Q VLAN..............................................................................................................58

6.1.1 VLAN Config ....................................................................................................59

6.2 Application Example for 802.1Q VLAN .......................................................................61

Chapter 7 Spanning Tree ............................................................................................................63

7.1 STP Config .................................................................................................................68

7.1.1 STP Config.......................................................................................................68

7.1.2 STP Summary..................................................................................................70

7.2 Port Config..................................................................................................................70

7.3 MSTP Instance ...........................................................................................................72

7.3.1 Region Config ..................................................................................................72

7.3.2 Instance Config ................................................................................................73

7.3.3 Instance Port Config.........................................................................................74

7.4 STP Security...............................................................................................................76

7.4.1 Port Protect ......................................................................................................76

7.4.2 TC Protect........................................................................................................78

7.5 Application Example for STP Function .......................................................................79

Chapter 8 Multicast.....................................................................................................................83

8.1 IGMP Snooping ..........................................................................................................85

IV

8.1.1 Snooping Config ..............................................................................................86

8.1.2 Port Config .......................................................................................................87

8.1.3 VLAN Config ....................................................................................................88

8.1.4 Multicast VLAN ................................................................................................90

8.2 Multicast IP .................................................................................................................93

8.2.1 Multicast IP Table .............................................................................................94

8.2.2 Static Multicast IP.............................................................................................94

8.3 Multicast Filter.............................................................................................................95

8.3.1 IP-Range..........................................................................................................96

8.3.2 Port Filter .........................................................................................................96

8.4 Packet Statistics..........................................................................................................98

Chapter 9 QoS..........................................................................................................................100

9.1 DiffServ.....................................................................................................................103

9.1.1 Port Priority ....................................................................................................103

9.1.2 802.1P/CoS mapping.....................................................................................105

9.1.3 DSCP Priority.................................................................................................106

9.1.4 Schedule Mode ..............................................................................................108

9.2 Bandwidth Control ....................................................................................................109

9.2.1 Rate Limit.......................................................................................................109

9.2.2 Storm Control ................................................................................................. 110

9.3 Voice VLAN .............................................................................................................. 112

9.3.1 Global Config ................................................................................................. 114

9.3.2 Port Config ..................................................................................................... 115

9.3.3 OUI Config ..................................................................................................... 116

Chapter 10 ACL .......................................................................................................................... 118

10.1 ACL Config ............................................................................................................... 118

10.1.1 ACL Summary................................................................................................ 118

10.1.2 ACL Create .................................................................................................... 118

10.1.3 MAC ACL ....................................................................................................... 119

10.1.4 Standard-IP ACL ............................................................................................120

10.1.5 Extend-IP ACL ...............................................................................................120

10.2 Policy Config.............................................................................................................121

10.2.1 Policy Summary .............................................................................................122

10.2.2 Policy Create..................................................................................................122

10.2.3 Action Create .................................................................................................123

10.3 Policy Binding ...........................................................................................................123

10.3.1 Binding Table .................................................................................................123

V

10.3.2 Port Binding ...................................................................................................124

10.3.3 VLAN Binding.................................................................................................124

10.4 Application Example for ACL ....................................................................................125

Chapter 11 PoE ..........................................................................................................................128

11.1 PoE Config ...............................................................................................................128

11.1.1 PoE Config.....................................................................................................129

11.1.2 PoE Profile .....................................................................................................131

11.2 PoE Time-Range ......................................................................................................132

11.2.1 Time-Range Summary ...................................................................................133

11.2.2 PoE Time-Range Create ................................................................................133

11.2.3 PoE Holiday Config........................................................................................134

Chapter 12 SNMP.......................................................................................................................136

12.1 SNMP Config ............................................................................................................138

12.1.1 Global Config .................................................................................................138

12.1.2 SNMP View....................................................................................................139

12.1.3 SNMP Group..................................................................................................140

12.1.4 SNMP User ....................................................................................................141

12.1.5 SNMP Community..........................................................................................143

12.2 Notification................................................................................................................145

12.3 RMON.......................................................................................................................146

12.3.1 History Control ...............................................................................................147

12.3.2 Event Config ..................................................................................................148

12.3.3 Alarm Config ..................................................................................................149

Chapter 13 LLDP ........................................................................................................................151

13.1 Basic Config .............................................................................................................155

13.1.1 Global Config .................................................................................................155

13.1.2 Port Config .....................................................................................................156

13.2 Device Info................................................................................................................157

13.2.1 Local Info .......................................................................................................157

13.2.2 Neighbor Info .................................................................................................158

13.3 Device Statistics........................................................................................................158

13.4 LLDP-MED ...............................................................................................................160

13.4.1 Global Config .................................................................................................161

13.4.2 Port Config .....................................................................................................161

13.4.3 Local Info .......................................................................................................163

13.4.4 Neighbor Info .................................................................................................164

Chapter 14 Maintenance ............................................................................................................166

VI

14.1 System Monitor.........................................................................................................166

14.1.1 CPU Monitor ..................................................................................................166

14.1.2 Memory Monitor .............................................................................................167

14.2 Log............................................................................................................................167

14.2.1 Log Table .......................................................................................................168

14.2.2 Local Log .......................................................................................................169

14.2.3 Remote Log ...................................................................................................169

14.2.4 Backup Log ....................................................................................................170

14.3 Device Diagnostics ...................................................................................................171

14.3.1 Cable Test ......................................................................................................171

14.3.2 Loopback .......................................................................................................172

14.4 Network Diagnostics .................................................................................................172

14.4.1 Ping................................................................................................................172

14.4.2 Tracert............................................................................................................173

Appendix A: Specifications .........................................................................................................175

Appendix B: Configuring the PCs ...............................................................................................176

Appendix C: Glossary.................................................................................................................178

VII

Package Contents

The following items should be found in your box:

 One Gigabit Smart Switch

 One power adapter (for TL-SG2210P)

One power cord (for TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452)

 Four rubber cushions (for TL-SG2210P)

Two mounting brackets and other fittings (for TL-SG2216/TL-SG2424/TL-SG2424P/

TL-SG2452)

 Installation

 Resource CD, including:

 This User Guide

 CLI Reference Guide

 SNMP Mibs

 Other Helpful Information

Note:

Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor.

1

Chapter 1 About this Guide

This User Guide contains information for setup and management of TL-SG2210P/TL-SG2216/

TL-SG2424/TL-SG2424P/TL-SG2452 Gigabit Smart Switch. Please read this guide carefully before operation.

1.1 Intended Readers

This Guide is intended for network managers familiar with IT concepts and network terminologies.

1.2 Conventions

In this Guide the following conventions are used:

The switch or TL-SG2210P/TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452 mentioned in this Guide stands for TL-SG2210P/TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452

Gigabit Smart Switch without any explanation.

Tips:

The TL-SG2210P/TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452 switchs are sharing this User

Guide. For simplicity, we will take TL-SG2424 for example throughout this Guide.

Menu Name→Submenu Name→Tab page indicates the menu structure. System→System

Info→System Summary means the System Summary page under the System Info menu option that is located under the System menu.

Bold font indicates a button, a toolbar icon, menu or menu item.

Symbols in this Guide:

Symbol Description

Note:

Ignoring this type of note might result in a malfunction or damage to the device.

Tips:

This format indicates important information that helps you make better use of your device.

1.3 Overview of This Guide

Chapter Introduction

Chapter 1 About This Guide

Introduces the guide structure and conventions.

Chapter 2 Introduction

Introduces the features, application and appearance of

TL-SG2210P/TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452 switch.

2

Chapter Introduction

Chapter 3 Login to the Switch Introduces how to log on to the Web management page.

Chapter 4 System

This module is used to configure system properties of the switch. Here mainly introduces:

System Info: Configure the description, system time and network parameters of the switch.

User Management: Configure the user name and password for users to log on to the Web management page with a certain access level.

System Tools: Manage the configuration file of the switch.

Access Security: Provide different security measures for the login to enhance the configuration management security.

Chapter 5 Switching

This module is used to configure basic functions of the switch.

Here mainly introduces:

Port: Configure the basic features for the port.

LAG: Configure Link Aggregation Group. LAG is to combine a number of ports together to make a single high-bandwidth data path.

Traffic Monitor: Monitor the traffic of each port.

MAC Address: Configure the address table of the switch.

DHCP Filtering: Monitor the process of the host obtaining the

IP address from DHCP server.

Chapter 6 VLAN

Chapter 7 Spanning Tree

This module is used to configure VLANs to control broadcast in

LANs. Here mainly introduces:

 802.1Q VLAN: Configure port-based VLAN.

This module is used to configure spanning tree function of the switch. Here mainly introduces:

STP Config: Configure and view the global settings of spanning tree function.

Port Config: Configure CIST parameters of ports.

MSTP Instance: Configure MSTP instances.

STP Security: Configure protection function to prevent devices from any malicious attack against STP features.

Chapter 8 Multicast

This module is used to configure multicast function of the switch.

Here mainly introduces:

IGMP Snooping: Configure global parameters of IGMP

Snooping function, port properties, VLAN and multicast

VLAN.

Multicast IP: Configure multicast IP table.

Multicast Filter: Configure multicast filter feature to restrict users ordering multicast programs.

Packet Statistics: View the multicast data traffic on each port of the switch, which facilitates you to monitor the IGMP messages in the network.

3

Chapter

Chapter 9 QoS

Chapter 10 ACL

Chapter 11 PoE

Chapter 12 SNMP

Chapter 13 LLDP

Introduction

This module is used to configure QoS function to provide different quality of service for various network applications and requirements. Here mainly introduces:

DiffServ: Configure priorities, port priority, 802.1P priority and

DSCP priority.

Bandwidth Control: Configure rate limit feature to control the traffic rate on each port; configure storm control feature to filter broadcast, multicast and UL frame in the network.

Voice VLAN: Configure voice VLAN to transmit voice data stream within the specified VLAN so as to ensure the transmission priority of voice data stream and voice quality.

This module is used to configure match rules and process policies of packets to filter packets in order to control the access of the illegal users to the network. Here mainly introduces:

ACL Config: ACL rules.

Policy Config: Configure operation policies.

Policy Binding: Bind the policy to a port/VLAN to take its effect on a specific port/VLAN.

This module is used to configure the PoE function for the switch to supply power for PD devices. Here mainly introduces:

PoE Config: Configure PoE function globally.

PoE Time-Range: Configure the effective time for PoE port to supply power..

This module is used to configure SNMP function to provide a management frame to monitor and maintain the network devices. Here mainly introduces:

SNMP Config: Configure global settings of SNMP function.

Notification: Configure notification function for the management station to monitor and process the events.

RMON: Configure RMON function to monitor network more efficiently.

This module is used to configure LLDP function to provide information for SNMP applications to simplify troubleshooting.

Here mainly introduces:

Basic Config: Configure the LLDP parameters of the device.

Device Info: View the LLDP information of the local device and its neighbors

Device Statistics: View the LLDP statistics of the local device

LLDP-MED: Configure LLDP-MED parameters of the device.

4

Chapter

Chapter 14 Maintenance

Introduction

This module is used to assemble the commonly used system tools to manage the switch. Here mainly introduces:

System Monitor: Monitor the memory and CPU of the switch.

Log: View configuration parameters on the switch.

Device Diagnostics: Test the connection status of the cable connected to the switch, test if the port of the switch and the connected device are available.

Network Diagnostics: Test if the destination is reachable and the account of router hops from the switch to the destination.

Appendix A Specifications

Lists the hardware specifications of the switch.

Appendix B Configure the PCs Introduces how to configure the PCs.

Appendix C Glossary

Lists the glossary used in this manual.

Return to CONTENTS

5

Chapter 2 Introduction

Thanks for choosing the TL-SG2210P/TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452 Gigabit

Smart Switch!

2.1 Overview of the Switch

Designed for workgroups and departments, TL-SG2210P/TL-SG2216/TL-SG2424/TL-SG2424P/

TL-SG2452 from TP-LINK provides wire-speed performance and full set of layer 2 management features. It provides a variety of service features and multiple powerful functions with high security.

The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. QoS and IGMP snooping/filtering optimize voice and video application. Link aggregation (LACP) increase aggregated bandwidth, optimizing the transport of business critical data. SNMP, RMON, WEB/CLI/Telnet Log-in bring abundant management policies. TL-SG2210P/TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452 switch integrates multiple functions with excellent performance, and is friendly to manage, which can fully meet the need of the users demanding higher networking performance.

2.2 Main Features

Resiliency and Availability

+ IEEE 802.1s Multiple Spanning Tree provides high link availability in multiple VLAN environments.

+ Multicast snooping automatically prevents flooding of IP multicast traffic.

+ Root Guard protects root bridge from malicious attack or configuration mistakes

Layer 2 Switching

+ Supports up to 512 VLANs simultaneously (out of 4K VLAN IDs).

Quality of Service

+ Supports L2/L3 granular CoS with 4 priority queues per port.

+ Rate limiting confines the traffic flow accurately according to the preset value.

Manageability

+ Supports Telnet, CLI, SNMP v1/v2c/v3, RMON and web access.

+ Port Mirroring enables monitoring selected ingress/egress traffic.

2.3 Appearance Description

2.3.1 Front Panel

The front panel of TL-SG2210P is shown as Figure 2-1.

Figure 2-1 Front Panel of TL-SG2210P

6

The following parts are located on the front panel of TL-SG2210P:

Reset: Press this button for five seconds or above to reset the software setting back to factory default setting.

LEDs

Name

Power

System

Link/Act

(Port 1-8)

SPF1, SFP2

PoE Status

(Port 1-8)

PoE Max

Status

On(Green)

Flashing/Off

Flashing

The switch is powered off or power supply is abnormal.

The switch is working normally.

Green

On/Off The switch is working abnormally.

On

A 1000Mbps device is connected to the corresponding port, but no activity.

Flashing Data is being transmitted or received.

Yellow

On

A 10/100Mbps device is connected to the corresponding port, but no activity.

Flashing Data is being transmitted or received.

Off

Indication

The switch is powered on.

On(Green)

Flashing

Off

On(Green)

Flashing

Off

On(Red)

Flashing

Off

No device is connected to the corresponding port.

An SFP transceiver is connected to the corresponding port, and it is connected to a device, but no activity.

A 1000Mbps device is connected to the corresponding port and transmitting data.

A 10/100Mbps device or no device is connected to the corresponding port.

The corresponding port is connected to a PoE PD and supplying power.

The PoE power circuit is overloaded or in short.

No PD is connected to the corresponding port, or no power is supplied.

Total power supply is >=46W but <53W.

Total power supply is >=53W.

Total power supply is <46W.

The front panel of TL-SG2216 is shown as Figure 2-2.

Figure 2-2 Front Panel of TL-SG2216

7

The front panel of TL-SG2424 is shown as Figure 2-3.

Figure 2-3 Front Panel of TL-SG2424

The front panel of TL-SG2424P is shown as Figure 2-4.

Figure 2-4 Front Panel of TL-SG2424P

The front panel of TL-SG2452 is shown as Figure 2-5.

Figure 2-5 Front Panel of TL-SG2452

The following parts are located on the front panel of TL-SG2216/TL-SG2424/TL-SG2424P/

TL-SG2452:

Reset: Press this button for five seconds or above to reset the software setting back to factory default setting.

10/100/1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps,

100Mbps or 1000Mbps. Each has a corresponding 1000Mbps LED and link/Act LED.

SFP Ports: Designed to install the SFP module. TL-SG2216/TL-SG2424/TL-SG2424P switch features some SFP transceiver slots that are shared with the associated RJ45 ports. The associated two ports are referred to as “combo” ports, which means they cannot be used simultaneously, otherwise only SFP ports work. TL-SG2452 features 4 individual SFP ports.

Note:

The SFP port can only be used with a gigabit module.

LEDs

For TL-SG2216/TL-SG2424:

Name

Power

Status

On Power is on.

Indication

Flashing Power supply is abnormal.

Off Power is off or power supply is abnormal.

8

Name

System

1000Mbps

Link/Act

Status Indication

On The switch is working abnormally.

Flashing The switch is working normally.

Off

On

Off

On

The switch is working abnormally.

A 1000Mbps device is connected to the corresponding port.

A 10/100Mbps device or no device is connected to the corresponding port.

A device is connected to the corresponding port but no activity.

Flashing Data is being transmitted or received.

Off No device is connected to the corresponding port.

For TL-SG2424P:

TL-SG2424P has a LED mode switch button which is for switching the LED status indication.

When the Speed LED is on, the port LED is indicating the data transmission rate. When the PoE

LED is on, the port LED is indicating the power supply status. By default the Speed LED is on.

Pressing the mode switch button, the Speed LED will turn off and the PoE LED will light up. Then the PoE LED will turn off after being on for 60 seconds and the Speed LED will light up again.

When the Speed LED is on, the port LED is indicating the data transmission rate.

Name

Power

System

10/100/1000Mbps

Status

On

Off

Flashing

Flashing

Indication

The switch is powered on.

The switch is powered off or power supply is abnormal.

Power supply is abnormal.

The switch works properly.

On/Off

Green

On

The switch works improperly.

A 1000Mbps device is connected to the corresponding port, but no activity.

Flashing Data is being transmitted or received.

Yellow

Off

On

A 10/100Mbps device is connected to the corresponding port, but no activity.

Flashing Data is being transmitted or received.

No device is connected to the corresponding port.

When the PoE LED is on, the port LED is indicating the power supply status.

Name

Power

System

Status

On

Off

Flashing

Flashing

On/Off

Indication

The switch is powered on.

The switch is powered off or power supply is abnormal.

Power supply is abnormal.

The switch works properly.

The switch works improperly.

9

Name

PoE Max

10/100/1000Mbps

Status

On

Flashing

Off

On

Green

Flashing

Indication

The remaining PoE power≤7W.

The remaining PoE power keeps ≤7W after this LED is on for 2 minutes.

The remaining PoE power≥7W.

The port is supplying power normally.

The supply power exceeds the corresponding port’s maximum power.

Yellow

Flashing Power-on self-test has failed.

Off No PoE power supply is provided on the port.

For TL-SG2452:

Name

PWR

Status

On

Flashing

Off

Indication

Power is on.

Power supply is abnormal.

Power is off or power supply is abnormal.

On The switch is working abnormally.

SYS Flashing The switch is working normally.

Green

10/100/1000Mbps

Yellow

Off The switch is working abnormally.

On

A 1000Mbps device is connected to the corresponding port but no activity.

Flashing Data is being transmitted or received.

On

A 10/100Mbps device is connected to the corresponding port but no activity.

Flashing Data is being transmitted or received.

Off No device is connected to the corresponding port.

2.3.2 Rear Panel

The rear panel of TL-SG2210P features a power socket and eight ports. Its rear panel is shown as the following figure.

Figure 2-6 Rear Panel of TL-SG2210P

10/100/1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps,

100Mbps or 1000Mbps. Each has a corresponding LED on the front panel.

SFP Ports: Designed to install the SFP module. The SFP port can only be used with a gigabit module.

10

Power Socket: Connect the female connector of the power cord here, and the male connector to the DC power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage (48V/1.25A).

The rear panel of TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452 features a power socket and a Grounding Terminal (marked with ), here we take TL-SG2424 for example.

Figure 2-7 Rear Panel of the switch

Grounding Terminal: The switch already comes with Lightning Protection Mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground

Cable.

AC Power Socket: Connect the female connector of the power cord here, and the male connector to the AC power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage (100-240V~ 50/60Hz 0.6A for TL-SG2216/TL-SG2424,

100-240V~ 50/60Hz 3.5A for TL-SG2424P and100-240V~ 50/60Hz 1.0A for TL-SG2452).

Return to CONTENTS

11

Chapter 3 Login to the Switch

3.1 Login

1) To access the configuration utility, open a web-browser and type in the default address http://192.168.0.1 in the address field of the browser, then press the Enter key.

Figure 3-1 Web-browser

Tips:

To log in to the switch, the IP address of your PC should be set in the same subnet addresses of the switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is

255.255.255.0. For the detailed instructions as to how to do this, please refer to Appendix B.

2) After a moment, a login window will appear, as shown in Figure 3-2. Enter admin for the User

Name and Password, both in lower case letters. Then click the Login button or press the Enter key.

Figure 3-2 Login

3.2 Configuration

After a successful login, the main page will appear as Figure 3-3, and you can configure the

function by clicking the setup menu on the left side of the screen.

12

Figure 3-3 Main Setup-Menu

Note:

Clicking Apply can only make the new configurations effective before the switch is rebooted. If you want to keep the configurations effective even the switch is rebooted, please click Save

Config. You are suggested to click Save Config before cutting off the power or rebooting the switch to avoid losing the new configurations.

Return to CONTENTS

13

Chapter 4 System

The System module is mainly for system configuration of the switch, including four submenus:

System Info, User Management, System Tools and Access Security.

4.1 System Info

The System Info, mainly for basic properties configuration, can be implemented on System

Summary, Device Description, System Time, Daylight Saving Time and System IP pages.

4.1.1 System Summary

On this page you can view the port connection status and the system information.

The port status diagram shows the working status of 24 10/100/1000Mbps RJ45 ports and 4 SFP ports of the switch.

Choose the menu System→System Info→System Summary to load the following page.

 Port Status

Figure 4-1 System Summary

Indicates the 1000Mbps port is not connected to a device.

Indicates the 1000Mbps port is at the speed of 1000Mbps.

Indicates the 1000Mbps port is at the speed of 10Mbps or 100Mbps.

Indicates the SFP port is not connected to a device.

Indicates the SFP port is at the speed of 1000Mbps.

14

When the cursor moves on the port, the detailed information of the port will be displayed.

Figure 4-2 Port Information

Port Info

Port:

Type:

Rate:

Status:

Displays the port number of the switch.

Displays the type of the port.

Displays the maximum transmission rate of the port.

Displays the connection status of the port.

Click a port to display the bandwidth utilization on this port. The actual rate divided by theoretical maximum rate is the bandwidth utilization. The following figure displays the bandwidth utilization monitored every four seconds. Monitoring the bandwidth utilization on each port facilitates you to monitor the network traffic and analyze the network abnormities.

Figure 4-3 Bandwidth Utilization

Bandwidth Utilization

Rx:

Tx:

Select Rx to display the bandwidth utilization of receiving packets on this port.

Select Tx to display the bandwidth utilization of sending packets on this port.

4.1.2 Device Description

On this page you can configure the description of the switch, including device name, device location and system contact.

Choose the menu System→System Info→Device Description to load the following page.

15

Figure 4-4 Device Description

The following entries are displayed on this screen:

Device Description

Device Name:

Device Location:

System Contact:

Enter the name of the switch.

Enter the location of the switch.

Enter your contact information.

4.1.3 System Time

System Time is the time displayed while the switch is running. On this page you can configure the system time and the settings here will be used for other time-based functions.

You can manually set the system time or synchronize with PC’s clock as the system time.

Choose the menu System→System Info→System Time to load the following page.

Figure 4-5 System Time

The following entries are displayed on this screen:

 Time Info

Current System Date:

Current Time Source:

Displays the current date and time of the switch.

Displays the current time source of the switch.

16

 Time Config

Manual:

Get Time from NTP

Server:

When this option is selected, you can set the date and time manually.

When this option is selected, you can configure the time zone and the IP Address for the NTP Server. The switch will get UTC automatically if it has connected to an NTP Server.

Time Zone: Select your local time.

Primary/Secondary Server: Enter the IP Address for the

NTP Server.

Update Rate: Specify the rate fetching time from NTP server.

Synchronize with

PC’S Clock:

When this option is selected, the administrator PC’s clock is utilized.

Note:

1. The system time will be restored to the default when the switch is restarted and you need to reconfigure the system time of the switch.

2. When Get Time from NTP Server is selected and no time server is configured, the switch will get time from the time server of the Internet if it has connected to the Internet.

4.1.4 Daylight Saving Time

Here you can configure the Daylight Saving Time of the switch.

Choose the menu System→System Info→Daylight Saving Time to load the following page.

Figure 4-6 Daylight Saving Time

The following entries are displayed on this screen:

 DST Config

DST Status: Enable or disable the DST.

17

Predefined Mode:

Recurring Mode:

Date Mode:

Select a predefined DST configuration.

USA: Second Sunday in March, 02:00 ~ First Sunday in

November, 02:00.

Australia: First Sunday in October, 02:00 ~ First Sunday in

April, 03:00.

Europe: Last Sunday in March, 01:00 ~ Last Sunday in

October, 01:00.

New Zealand: Last Sunday in September, 02:00 ~ First

Sunday in April, 03:00.

Specify the DST configuration in recurring mode. This configuration is recurring in use.

Offset: Specify the time adding in minutes when Daylight

Saving Time comes.

Start/End Time: Select starting time and ending time of

Daylight Saving Time.

Specify the DST configuration in Date mode. This configuration is recurring in use.

Offset: Specify the time adding in minutes when Daylight

Saving Time comes.

Start/End Time: Select starting time and ending time of

Daylight Saving Time.

Note:

1. When the DST is disabled, the predefined mode, recurring mode and date mode cannot be configured.

2. When the DST is enabled, the default daylight saving time is of European in predefined mode.

4.1.5 System IP

Each device in the network possesses a unique IP Address. You can log on to the Web management page to operate the switch using this IP Address. The switch supports three modes to obtain an IP address: Static IP, DHCP and BOOTP. The IP address obtained using a new mode will replace the original IP address. On this page you can configure the system IP of the switch.

Choose the menu System→System Info→System IP to load the following page.

Figure 4-7 System IP

18

The following entries are displayed on this screen:

IP Config

MAC Address:

IP Address Mode:

Management VLAN:

IP Address:

Subnet Mask:

Default Gateway:

Displays MAC Address of the switch.

Select the mode to obtain IP Address for the switch.

Static IP: When this option is selected, you should enter IP

Address, Subnet Mask and Default Gateway manually.

DHCP: When this option is selected, the switch will obtain network parameters from the DHCP Server.

BOOTP: When this option is selected, the switch will obtain network parameters from the BOOTP Server.

Enter the ID of management VLAN, the only VLAN through which you can get access to the switch. By default VLAN1 owning all the ports is the Management VLAN and you can access the switch via any port on the switch. However, if another VLAN is created and set to be the Management VLAN, you may have to reconnect the management station to a port that is a member of the

Management VLAN.

Enter the system IP of the switch. The default system IP is

192.168.0.1 and you can change it appropriate to your needs.

Enter the subnet mask of the switch.

Enter the default gateway of the switch.

Note:

1. Changing the IP address to a different IP segment will interrupt the network communication, so please keep the new IP address in the same IP segment with the local network.

2. The switch only possesses one IP address. The IP address configured will replace the original

IP address.

3. If the switch gets the IP address from DHCP server, you can see the configuration of the switch in the DHCP server; if DHCP option is selected but no DHCP server exists in the network, a few minutes later, the switch will restore the setting to the default.

4. If DHCP or BOOTP option is selected, the switch will get network parameters dynamically from the Internet, which means that IP address, subnet mask and default gateway can not be configured.

5. By default, the IP address is 192.168.0.1.

4.2 User Management

User Management functions to configure the user name and password for users to log on to the

Web management page with a certain access level so as to protect the settings of the switch from being randomly changed.

The User Management function can be implemented on User Table and User Config pages.

4.2.1 User Table

On this page you can view the information about the current users of the switch.

Choose the menu System→User Management→User Table to load the following page.

19

Figure 4-8 User Table

4.2.2 User Config

On this page you can configure the access level of the user to log on to the Web management page. The switch provides two access levels: Guest and Admin. The guest only can view the settings without the right to configure the switch; the admin can configure all the functions of the switch. The Web management pages contained in this guide are subject to the admin’s login without any explanation.

Choose the menu System→User Management→User Config to load the following page.

Figure 4-9 User Config

The following entries are displayed on this screen:

User Info

User Name:

Access Level:

User Status:

Password:

Create a name for users’ login.

Select the access level to login.

Admin: Admin can edit, modify and view all the settings of different functions.

Guest: Guest only can view the settings without the right to edit and modify.

Select Enable/Disable the user configuration.

Type a password for users’ login.

20

Confirm Password:

Password Display

Mode:

Retype the password.

Simple: Select a simple password display mode.

Cipher: Select a cipher password display mode.

User Table

Select: Select the desired entry to delete the corresponding user information. It is multi-optional. The current user information can’t be deleted.

User ID, Name,

Access Level and status:

Operation:

Displays the current user ID, user name, access level and user status.

Click the Edit button of the desired entry, and you can edit the corresponding user information. After modifying the settings, please click the Modify button to make the modification effective.

Access level and user status of the current user information cannot be modified.

4.3 System Tools

The System Tools function, allowing you to manage the configuration file of the switch, can be implemented on Config Restore, Config Backup, Firmware Upgrade, System Reboot and

System Reset pages.

4.3.1 Config Restore

On this page you can upload a backup configuration file to restore your switch to this previous configuration.

Choose the menu System→System Tools→Config Restore to load the following page.

Figure 4-10 Config Restore

The following entries are displayed on this screen:

 Config Restore

Restore Config: Click the Restore Config button to restore the backup configuration file. It will take effect after the switch automatically reboots.

21

Note:

1. It will take a few minutes to restore the configuration. Please wait without any operation.

2. To avoid any damage, please don’t power down the switch while being restored.

3. After being restored, the current settings of the switch will be lost. Wrong uploaded configuration file may cause the switch unmanaged.

4.3.2 Config Backup

On this page you can download the current configuration and save it as a file to your computer for your future configuration restore.

Choose the menu System→System Tools→Config Backup to load the following page.

Figure 4-11 Config Backup

The following entries are displayed on this screen:

Config Backup

Backup Config: Click the Backup Config button to save the current configuration as a file to your computer. You are suggested to take this measure before upgrading.

Note:

It will take a few minutes to backup the configuration. Please wait without any operation.

4.3.3 Firmware Upgrade

The switch system can be upgraded via the Web management page. To upgrade the system is to get more functions and better performance. Go to http://www.tp-link.com

to download the updated firmware.

Choose the menu System→System Tools→Firmware Upgrade to load the following page.

22

Figure 4-12 Firmware Upgrade

Note:

1. Don’t interrupt the upgrade.

2. Please select the proper software version matching with your hardware to upgrade.

3. To avoid damage, please don't turn off the device while upgrading.

4. After upgrading, the device will reboot automatically.

5. You are suggested to backup the configuration before upgrading.

4.3.4 System Reboot

On this page you can reboot the switch and return to the login page. Please save the current configuration before rebooting to avoid losing the configuration unsaved

Choose the menu System→System Tools→System Reboot to load the following page.

Figure 4-13 System Reboot

Note:

To avoid damage, please don't turn off the device while rebooting.

4.3.5 System Reset

On this page you can reset the switch to the default. All the settings will be cleared after the switch is reset.

Choose the menu System→System Tools→System Reset to load the following page.

23

Figure 4-14 System Reset

Note:

After the system is reset, the switch will be reset to the default and all the settings will be cleared.

4.4 Access Security

Access Security provides different security measures for the remote login so as to enhance the configuration management security. It can be implemented on Access Control, SSL Config and

SSH Config pages.

4.4.1 Access Control

On this page you can control the users logging on to the Web management page to enhance the

configuration management security. The definitions of Admin and Guest refer to 4.2 User

Management

.

Choose the menu System→Access Security→Access Control to load the following page.

Figure 4-15 Access Control

24

The following entries are displayed on this screen:

Access Control Config

Control Mode:

IP Address & Mask

MAC Address:

Port:

Select the control mode for users to log on to the Web management page.

IP-based: Select this option to limit the IP-range of the users for login.

MAC-based: Select this option to limit the MAC Address of the users for login.

Port-based: Select this option to limit the ports for login.

These fields can be available for configuration only when IP-based mode is selected. Only the users within the IP-range you set here are allowed for login.

The field can be available for configuration only when MAC-based mode is selected. Only the user with this MAC Address you set here are allowed for login.

The field can be available for configuration only when Port-based mode is selected. Only the users connected to these ports you set here are allowed for login.

Session Config

Session Timeout: If you do nothing with the Web management page within the timeout time, the system will log out automatically. If you want to reconfigure, please login again.

 Access User Number

Number Control:

Admin Number:

Guest Number:

Select Enable/Disable the Number Control function.

Enter the maximum number of the users logging on to the Web management page as Admin.

Enter the maximum number of the users logging on to the Web management page as Guest.

4.4.2 SSL Config

SSL (Secure Sockets Layer), a security protocol, is to provide a secure connection for the application layer protocol (e.g. HTTP) communication based on TCP. SSL is widely used to secure the data transmission between the Web browser and servers. It is mainly applied through ecommerce and online banking.

SSL mainly provides the following services:

1. Authenticate the users and the servers based on the certificates to ensure the data are transmitted to the correct users and servers;

2. Encrypt the data transmission to prevent the data being intercepted;

3. Maintain the integrality of the data to prevent the data being altered in the transmission.

Adopting asymmetrical encryption technology, SSL uses key pair to encrypt/decrypt information. A key pair refers to a public key (contained in the certificate) and its corresponding private key. By

25

default the switch has a certificate (self-signed certificate) and a corresponding private key. The

Certificate/Key Download function enables the user to replace the default key pair.

After SSL is effective, you can log on to the Web management page via https://192.168.0.1

. For the first time you use HTTPS connection to log into the switch with the default certificate, you will be prompted that “The security certificate presented by this website was not issued by a trusted certificate authority” or “Certificate Errors”. Please add this certificate to trusted certificates or continue to this website.

On this page you can configure the SSL function.

Choose the menu System→Access Security→SSL Config to load the following page.

Figure 4-16 SSL Config

The following entries are displayed on this screen :

 Global Config

SSL: Select Enable/Disable the SSL function on the switch.

 Certificate Download

Certificate File: Select the desired certificate to download to the switch. The certificate must be BASE64 encoded.

Key Download

Key File: Select the desired SSL Key to download to the switch. The key must be BASE64 encoded.

Note:

1. The SSL certificate and key downloaded must match each other; otherwise the HTTPS connection will not work.

2. The SSL certificate and key downloaded will not take effect until the switch is rebooted.

3. To establish a secured connection using https, please enter https:// into the URL field of the browser.

26

4. It may take more time for https connection than that for http connection, because https connection involves authentication, encryption and decryption etc.

4.4.3 SSH Config

As stipulated by IETF (Internet Engineering Task Force), SSH (Secure Shell) is a security protocol established on application and transport layers. SSH-encrypted-connection is similar to a telnet connection, but essentially the old telnet remote management method is not safe, because the password and data transmitted with plain-text can be easily intercepted. SSH can provide information security and powerful authentication when you log on to the switch remotely through an insecure network environment. It can encrypt all the transmission data and prevent the information in a remote management being leaked.

Comprising server and client, SSH has two versions, V1 and V2 which are not compatible with each other. In the communication, SSH server and client can auto-negotiate the SSH version and the encryption algorithm. After getting a successful negotiation, the client sends authentication request to the server for login, and then the two can communicate with each other after successful authentication. This switch supports SSH server and you can log on to the switch via SSH connection using SSH client software.

SSH key can be downloaded into the switch. If the key is successfully downloaded, the certificate authentication will be preferred for SSH access to the switch.

Choose the menu System→Access Security→SSH Config to load the following page.

Figure 4-17 SSH Config

The following entries are displayed on this screen :

 Global Config

SSH:

Protocol V1:

Protocol V2:

Select Enable/Disable SSH function.

Select Enable/Disable SSH V1 to be the supported protocol.

Select Enable/Disable SSH V2 to be the supported protocol.

27

Idle Timeout:

Max Connect:

Specify the idle timeout time. The system will automatically release the connection when the time is up. The default time is

120 seconds.

Specify the maximum number of the connections to the SSH server. No new connection will be established when the number of the connections reaches the maximum number you set. The default value is 5.

 Key Download

Key Type:

Key File:

Download:

Select the type of SSH Key to download. The switch supports three types: SSH-1 RSA, SSH-2 RSA and SSH-2 DSA.

Select the desired key file to download.

Click the Download button to download the desired key file to the switch.

Note:

1. Please ensure the key length of the downloaded file is in the range of 256 to 3072 bits.

2. After the Key File is downloaded, the user’s original key of the same type will be replaced.

The wrong uploaded file will result in the SSH access to the switch via Password authentication.

Application Example 1 for SSH:

 Network Requirements

1. Log on to the switch via password authentication using SSH and the SSH function is enabled on the switch.

2. PuTTY client software is recommended.

Configuration Procedure

1. Open the software to log on to the interface of PuTTY. Enter the IP address of the switch into

Host Name field; keep the default value 22 in the Port field; select SSH as the Connection type.

28

2. Click the Open button in the above figure to log on to the switch. Enter the login user name and password, and then you can continue to configure the switch.

Application Example 2 for SSH:

Network Requirements

1. Log on to the switch via key authentication using SSH and the SSH function is enabled on the switch.

2. PuTTY client software is recommended.

 Configuration Procedure

1. Select the key type and key length, and generate SSH key.

29

Note:

1. The key length is in the range of 256 to 3072 bits.

2. During the key generation, randomly moving the mouse quickly can accelerate the key generation.

2. After the key is successfully generated, please save the public key and private key to the computer.

3. On the Web management page of the switch, download the public key file saved in the computer to the switch.

30

Note:

1. The key type should accord with the type of the key file.

2. The SSH key downloading can not be interrupted.

4. After the public key and private key are downloaded, please log on to the interface of PuTTY and enter the IP address for login.

5. Click Browse to download the private key file to SSH client software and click Open.

31

After successful authentication, please enter the login user name. If you log on to the switch without entering password, it indicates that the key has been successfully downloaded.

Return to CONTENTS

32

Chapter 5 Switching

Switching module is used to configure the basic functions of the switch, including five submenus:

Port, LAG, Traffic Monitor, MAC Address and DHCP Filtering.

5.1 Port

The Port function, allowing you to configure the basic features for the port, is implemented on the

Port Config, Port Mirror, Port Security , Port Isolation and Loopback Detection pages.

5.1.1 Port Config

On this page, you can configure the basic parameters for the ports. When the port is disabled, the packets on the port will be discarded. Disabling the port which is vacant for a long time can reduce the power consumption effectively. And you can enable the port when it is in need.

The parameters will affect the working mode of the port, please set the parameters appropriate to your needs.

Choose the menu Switching→Port→Port Config to load the following page.

Figure 5-1 Port Config

The following entries are displayed on this screen:

 Port Config

Port Select:

Select:

Port:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for configuration. It is multi-optional.

Displays the port number.

33

Description:

Status:

Speed and Duplex:

Flow Control:

Give a description to the port for identification.

Allows you to Enable/Disable the port. When Enable is selected, the port can forward the packets normally.

Select the Speed and Duplex mode for the port. The device connected to the switch should be in the same Speed and

Duplex mode with the switch. When “Auto” is selected, the

Speed and Duplex mode will be determined by auto-negotiation.

For the SFP port, this switch does not support auto-negotiation.

Allows you to Enable/Disable the Flow Control feature. When

Flow Control is enabled, the switch can synchronize the speed with its peer to avoid the packet loss caused by congestion.

Displays the LAG number which the port belongs to. LAG:

Note:

1. The switch can not be managed through the disabled port. Please enable the port which is used to manage the switch.

2. The parameters of the port members in a LAG should be set as the same.

3. When using the SFP port with a 100M module or a gigabit module, you need to configure its corresponding Speed and Duplex mode. For 100M module, please select 100MFD while select 1000MFD for gigabit module. By default, the Speed and Duplex mode of SFP port is

1000MFD.

5.1.2 Port Mirror

Port Mirror, the packets obtaining technology, functions to forward copies of packets from one/multiple ports (mirrored port) to a specific port (mirroring port). Usually, the mirroring port is connected to a data diagnose device, which is used to analyze the mirrored packets for monitoring and troubleshooting the network.

Choose the menu Switching→Port→Port Mirror to load the following page.

Figure 5-2 Mirror Group List

34

The following entries are displayed on this screen.

Mirror Group List

Group:

Mirroring:

Mode:

Mirrored Port:

Operation:

Displays the mirror group number.

Displays the mirroring port number.

Displays the mirror mode. The value will be "Ingress" or "Egress".

Displays the mirrored ports.

Click Edit to configure the mirror group.

Click Edit to display the following figure.

Figure 5-3 Port Mirror Config

The following entries are displayed on this screen:

Mirror Group

Select the mirror group number you want to configure.

Number:

Mirroring Port

Mirroring Port: Select the mirroring port number.

35

 Mirrored Port

Port Select:

Select:

Port:

Ingress:

Egress:

LAG:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port as a mirrored port. It is multi-optional.

Displays the port number.

Select Enable/Disable the Ingress feature. When the Ingress is enabled, the incoming packets received by the mirrored port will be copied to the mirroring port.

Select Enable/Disable the Egress feature. When the Egress is enabled, the outgoing packets sent by the mirrored port will be copied to the mirroring port.

Displays the LAG number which the port belongs to. The LAG member can not be selected as the mirrored port or mirroring port.

Note:

1. The LAG member can not be selected as the mirrored port or mirroring port.

2. A port can not be set as the mirrored port and the mirroring port simultaneously.

3. The Port Mirror function can take effect span the multiple VLANs.

5.1.3 Port Security

MAC Address Table maintains the mapping relationship between the port and the MAC address of the connected device, which is the base of the packet forwarding. The capacity of MAC Address

Table is fixed. MAC Address Attack is the attack method that the attacker takes to obtain the network information illegally. The attacker uses tools to generate the cheating MAC address and quickly occupy the MAC Address Table. When the MAC Address Table is full, the switch will broadcast the packets to all the ports. At this moment, the attacker can obtain the network information via various sniffers and attacks. When the MAC Address Table is full, the packets traffic will flood to all the ports, which results in overload, lower speed, packets drop and even breakdown of the system.

Port Security is to protect the switch from the malicious MAC Address Attack by limiting the maximum number of MAC addresses that can be learned on the port. The port with Port Security feature enabled will learn the MAC address dynamically. When the learned MAC address number reaches the maximum, the port will stop learning. Thereafter, the other devices with the MAC address unlearned can not access to the network via this port.

Choose the menu Switching→Port→Port Security to load the following page.

36

Figure 5-4 Port Security

The following entries are displayed on this screen:

 Port Security

Select:

Port:

Max Learned MAC:

Learned Num:

Learn Mode:

Status:

Select the desired port for Port Security configuration. It is multi-optional.

Displays the port number.

Specify the maximum number of MAC addresses that can be learned on the port.

Displays the number of MAC addresses that have been learned on the port.

Select the Learn Mode for the port.

Dynamic: When Dynamic mode is selected, the learned

MAC address will be deleted automatically after the aging time.

Static: When Static mode is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be cleared after the switch is rebooted.

Permanent: When Permanent mode is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be saved even the switch is rebooted.

Select Enable/Disable the Port Security feature for the port.

Note:

The Port Security function is disabled for the LAG port member. Only the port is removed from the

LAG, will the Port Security function be available for the port.

37

5.1.4 Port Isolation

Port Isolation provides a method of restricting traffic flow to improve the network security by forbidding the port to forward packets to the ports that are not on its forward portlist.

Choose the menu Switching→Port→Port Isolation to load the following page.

Figure 5-5 Port Isolation

The following entries are displayed on this screen:

Port Isolation Config

From Port/To Port:

Forward Portlist:

Port Isolation List

Port:

Forward Portlist:

Select the port number in this range to set their forward list.

Select the port that to be forwarded to.

Displays the port number.

Displays the forward portlist.

38

5.1.5 Loopback Detection

With loopback detection feature enabled, the switch can detect loops using loopback detection packets. When a loop is detected, the switch will display an alert or further block the corresponding port according to the port configuration.

Choose the menu Switching→Port→Loopback Detection to load the following page.

Figure 5-6 Loopback Detection Config

The following entries are displayed on this screen :

 Global Config

LoopbackDetection

Status:

Detection Interval:

Automatic

Recovery Time:

Web Refresh Status:

Web Refresh Interval:

Here you can enable or disable Loopback Detection function globally.

Set a Loopback Detection interval between 1 and 1000 seconds.

By default, it’s 30 seconds.

Time after which the blocked port would automatically recover to normal status. It can be set as integral times of detection interval.

Here you can enable or disable web automatic refresh.

Set a web refresh interval between 3 and 100 seconds. By default, it’s 3 seconds.

39

 Port Config

Port Select:

Select:

Port:

Status:

Operation Mode:

Recovery Mode:

Loop Status:

Block Status:

LAG:

Manual Recover:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for Loopback Detection configuration. It is multi-optional.

Displays the port number.

Enable or disable Loopback Detection function for the port.

Select the mode how the switch processes the detected loops.

 Alert: When a loop is detected, display an alert.

 Port based: When a loop is detected, display an alert and block the port.

Select the mode how the blocked port recovers to normal status.

 Auto: Block status can be automatically removed after recovery time.

 Manual: Block status only can be removed manually.

Displays the port status whether a loopback is detected.

Displays the port status about block or unblock.

Displays the LAG number the port belongs to.

Manually remove the block status of selected ports.

Note:

1. Recovery Mode is not selectable when Alert is chosen in Operation Mode.

2. Loopback Detection must coordinate with storm control.

5.2 LAG

LAG (Link Aggregation Group) is to combine a number of ports together to make a single high-bandwidth data path, so as to implement the traffic load sharing among the member ports in the group and to enhance the connection reliability.

For the member ports in an aggregation group, their basic configuration must be the same. The basic configuration includes STP, QoS, VLAN, port attributes, MAC Address Learning mode and other associated settings. The further explains are following:

If the ports, which are enabled for the 802.1Q VLAN, STP, QoS and Port Configuration

(Speed and Flow Control), are in a LAG, their configurations should be the same.

The ports, which are enabled for the half-duplex, Port Security, Port Mirror and MAC

Address Filtering, can not be added to the LAG.

If the LAG is needed, you are suggested to configure the LAG function here before configuring the other functions for the member ports.

40

Tips:

1. Calculate the bandwidth for a LAG: If a LAG consists of the four ports in the speed of

1000Mbps Full Duplex, the whole bandwidth of the LAG is up to 8000Mbps (2000Mbps * 4) because the bandwidth of each member port is 2000Mbps counting the up-linked speed of

1000Mbps and the down-linked speed of 1000Mbps.

2. The traffic load of the LAG will be balanced among the ports according to the Aggregate

Arithmetic. If the connections of one or several ports are broken, the traffic of these ports will be transmitted on the normal ports, so as to guarantee the connection reliability.

The LAG function is implemented on the LAG Table, Static LAG and LACP Config configuration pages.

5.2.1 LAG Table

On this page, you can view the information of the current LAG of the switch.

Choose the menu Switching→LAG→LAG Table to load the following page.

Figure 5-7 LAG Table

The following entries are displayed on this screen:

Global Config

Hash Algorithm: Select the applied scope of Aggregate Arithmetic, which results in choosing a port to transfer the packets.

SRC MAC + DST MAC: When this option is selected, the

Aggregate Arithmetic will apply to the source and destination

MAC addresses of the packets.

SRC IP + DST IP: When this option is selected, the

Aggregate Arithmetic will apply to the source and destination

IP addresses of the packets.

LAG Table

Select:

Group Number:

Description:

Member:

Select the desired LAG. It is multi-optional.

Displays the LAG number here.

Displays the description of LAG.

Displays the LAG member.

41

Operation: Allows you to view or modify the information for each LAG.

 Edit: Click to modify the settings of the LAG.

 Detail: Click to get the information of the LAG.

Click the Detail button for the detailed information of your selected LAG.

Figure 5-8 Detailed Information

5.2.2 Static LAG

On this page, you can manually configure the LAG.

Choose the menu Switching→LAG→Static LAG to load the following page.

Figure 5-9 Manually Config

The following entries are displayed on this screen:

 LAG Config

Group Number: Select a Group Number for the LAG.

42

Description:

Member Port

Member Port:

Displays the description of the LAG.

Select the port as the LAG member. Clearing all the ports of the LAG will delete this LAG.

Tips:

1. The LAG can be deleted by clearing its all member ports.

2. A port can only be added to a LAG. If a port is the member of a LAG, the port number will be displayed in gray and can not be selected.

5.2.3 LACP Config

LACP (Link Aggregation Control Protocol) is defined in IEEE802.3ad and enables the dynamic link aggregation and disaggregation by exchanging LACP packets with its partner. The switch can dynamically group similarly configured ports into a single logical link, which will highly extend the bandwidth and flexibly balance the load.

With the LACP feature enabled, the port will notify its partner of the system priority, system MAC, port priority, port number and operation key (operation key is determined by the physical properties of the port, upper layer protocol and admin key). The device with higher priority will lead the aggregation and disaggregation. System priority and system MAC decide the priority of the device. The smaller the system priority, the higher the priority of the device is. With the same system priority, the device owning the smaller system MAC has the higher priority. The device with the higher priority will choose the ports to be aggregated based on the port priority, port number and operation key. Only the ports with the same operation key can be selected into the same aggregation group. In an aggregation group, the port with smaller port priority will be considered as the preferred one. If the two port priorities are equal, the port with smaller port number is preferred. After an aggregation group is established, the selected ports can be aggregated together as one port to transmit packets.

On this page, you can configure the LACP feature of the switch.

Choose the menu Switching→LAG→LACP Config to load the following page.

43

Figure 5-10 LACP Config

The following entries are displayed on this screen :

 Global Config

System Priority: Specify the system priority for the switch. The system priority and

MAC address constitute the system identification (ID). A lower system priority value indicates a higher system priority. When exchanging information between systems, the system with higher priority determines which link aggregation a link belongs to, and the system with lower priority adds the proper links to the link aggregation according to the selection of its partner.

 LACP Config

Port Select:

Select:

Port:

Admin Key:

Port Priority:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for LACP configuration. It is multi-optional.

Displays the port number.

Specify an Admin Key for the port. The member ports in a dynamic aggregation group must have the same Admin Key.

Specify a Port Priority for the port. This value determines the priority of the port to be selected as the dynamic aggregation group member. The port with smaller Port Priority will be considered as the preferred one. If the two port priorities are equal; the port with smaller port number is preferred.

44

Mode:

Status:

LAG:

Specify LACP mode for your selected port.

Enable/Disable the LACP feature for your selected port.

Displays the LAG number which the port belongs to.

5.3 Traffic Monitor

The Traffic Monitor function, monitoring the traffic of each port, is implemented on the Traffic

Summary and Traffic Statistics pages.

5.3.1 Traffic Summary

Traffic Summary screen displays the traffic information of each port, which facilitates you to monitor the traffic and analyze the network abnormity.

Choose the menu Switching→Traffic Monitor→Traffic Summary to load the following page.

Figure 5-11 Traffic Summary

The following entries are displayed on this screen:

 Auto Refresh

Auto Refresh:

Refresh Rate:

Traffic Summary

Allows you to Enable/Disable refreshing the Traffic Summary automatically.

Enter a value in seconds to specify the refresh interval.

Port Select: Click the Select button to quick-select the corresponding port based on the port number you entered.

45

Port:

Packets Rx:

Packets Tx:

Octets Rx:

Octets Tx:

Statistics:

Displays the port number.

Displays the number of packets received on the port. The error packets are not counted in.

Displays the number of packets transmitted on the port.

Displays the number of octets received on the port. The error octets are counted in.

Displays the number of octets transmitted on the port.

Click the Statistics button to view the detailed traffic statistics of the port.

5.3.2 Traffic Statistics

Traffic Statistics screen displays the detailed traffic information of each port, which facilitates you to monitor the traffic and locate faults promptly.

Choose the menu Switching→Traffic Monitor→Traffic Statistics to load the following page.

Figure 5-12 Traffic Statistics

The following entries are displayed on this screen:

 Auto Refresh

Auto Refresh:

Refresh Rate:

Allows you to Enable/Disable refreshing the Traffic Summary automatically.

Enter a value in seconds to specify the refresh interval.

46

 Statistics

Port:

Received:

Sent:

Broadcast:

Multicast:

Unicast:

Alignment Errors:

UndersizePkts:

Pkts64Octets:

Pkts65to127Octets:

Pkts128to255Octets:

Pkts256to511Octets:

Pkts512to1023Octets:

PktsOver1023Octets:

Collisions:

Enter a port number and click the Select button to view the traffic statistics of the corresponding port.

Displays the details of the packets received on the port.

Displays the details of the packets transmitted on the port.

Displays the number of good broadcast packets received or transmitted on the port. The error frames are not counted in.

Displays the number of good multicast packets received or transmitted on the port. The error frames are not counted in.

Displays the number of good unicast packets received or transmitted on the port. The error frames are not counted in.

For TL-SG2216/TL-SG2424/TL-SG2424P:

Displays the number of the received packets that have a bad

Frame Check Sequence (FCS) with a non-integral octet

(Alignment Error) and have a bad FCS with an integral octet

(CRC Error). The length of the packet is between 64 bytes and

1518 bytes.

For TL-SG2452:

Displays the number of the received packets that have a bad

Frame Check Sequence (FCS) . The length of the packet is from

64 bytes to maximal bytes of the jumbo frame(usually 10240 bytes).

Displays the number of the received packets (excluding error packets) that are less than 64 bytes long.

Displays the number of the received packets (including error packets) that are 64 bytes long.

Displays the number of the received packets (including error packets) that are between 65 and 127 bytes long.

Displays the number of the received packets (including error packets) that are between 128 and 255 bytes long.

Displays the number of the received packets (including error packets) that are between 256 and 511 bytes long.

Displays the number of the received packets (including error packets) that are between 512 and 1023 bytes long.

Displays the number of the received packets (including error packets) that are over 1023 bytes.

Displays the number of collisions experienced by a port during packet transmissions.

5.4 MAC Address

The main function of the switch is forwarding the packets to the correct ports based on the destination MAC address of the packets. Address Table contains the port-based MAC address information, which is the base for the switch to forward packets quickly. The entries in the Address

Table can be updated by auto-learning or configured manually. Most the entries are generated and updated by auto-learning. In the stable networks, the static MAC address entries can facilitate the

47

switch to reduce broadcast packets and enhance the efficiency of packets forwarding remarkably.

The address filtering feature allows the switch to filter the undesired packets and forbid its forwarding so as to improve the network security.

The types and the features of the MAC Address Table are listed as the following:

Type

Static

Address Table

Dynamic

Address Table

Filtering

Address Table

Configuration

Way

Manually configuring

Automatically learning

Manually configuring

Aging out

No

Yes reboot

(if the configuration the port is saved) bound MAC address and

Yes

No

No Yes

The bound MAC address can not be learned by the other ports in the same

VLAN.

The bound MAC address can be learned by the other ports in the same VLAN.

-

Table 5-1 Types and features of Address Table

This function includes four submenus: Address Table, Static Address, Dynamic Address and

Filtering Address.

5.4.1 Address Table

On this page, you can view all the information of the Address Table.

Choose the menu Switching→MAC Address→Address Table to load the following page.

Figure 5-13 Address Table

The following entries are displayed on this screen:

 Search Option

MAC Address:

VLAN ID:

Enter the MAC address of your desired entry.

Enter the VLAN ID of your desired entry.

48

Port:

Type:

Select the corresponding port number of your desired entry.

Select the type of your desired entry.

All: This option allows the address table to display all the address entries.

Static: This option allows the address table to display the static address entries only.

Dynamic: This option allows the address table to display the dynamic address entries only.

Filtering: This option allows the address table to display the filtering address entries only.

 Address Table

MAC Address:

VLAN ID:

Port:

Type:

Aging Status:

Displays the MAC address learned by the switch.

Displays the corresponding VLAN ID of the MAC address.

Displays the corresponding Port number of the MAC address.

Displays the Type of the MAC address.

Displays the Aging status of the MAC address.

5.4.2 Static Address

The static address table maintains the static address entries which can be added or removed manually, independent of the aging time. In the stable networks, the static MAC address entries can facilitate the switch to reduce broadcast packets and remarkably enhance the efficiency of packets forwarding without learning the address. The static MAC address learned by the port with

Port Security enabled in the static learning mode will be displayed in the Static Address Table.

Choose the menu Switching→MAC Address→Static Address to load the following page.

Figure 5-14 Static Address

49

The following entries are displayed on this screen:

Create Static Address

MAC Address:

VLAN ID:

Port:

Search Option

Enter the static MAC Address to be bound.

Enter the corresponding VLAN ID of the MAC address.

Select a port from the pull-down list to be bound.

Search Option: Select a Search Option from the pull-down list and click the Search button to find your desired entry in the Static Address Table.

MAC: Enter the MAC address of your desired entry.

VLAN ID: Enter the VLAN ID number of your desired entry.

Port: Enter the Port number of your desired entry.

Static Address Table

Select:

MAC Address:

VLAN ID:

Port:

Type:

Aging Status:

Select the entry to delete or modify the corresponding port number. It is multi-optional.

Displays the static MAC Address.

Displays the corresponding VLAN ID of the MAC address.

Displays the corresponding Port number of the MAC address. Here you can modify the port number to which the MAC address is bound.

The new port should be in the same VLAN.

Displays the Type of the MAC address.

Displays the Aging Status of the MAC address.

Note:

1. If the corresponding port number of the MAC address is not correct, or the connected port (or the device) has been changed, the switch can not be forward the packets correctly. Please reset the static address entry appropriately.

2. If the MAC address of a device has been added to the Static Address Table, connecting the device to another port will cause its address not to be recognized dynamically by the switch.

Therefore, please ensure the entries in the Static Address Table are correct and valid.

3. The MAC address in the Static Address Table can not be added to the Filtering Address Table or bound to a port dynamically.

5.4.3 Dynamic Address

The dynamic address can be generated by the auto-learning mechanism of the switch. The

Dynamic Address Table can update automatically by auto-learning or the MAC address aging out mechanism.

To fully utilize the MAC address table, which has a limited capacity, the switch adopts an aging mechanism for updating the table. That is, the switch removes the MAC address entries related to a network device if no packet is received from the device within the aging time.

On this page, you can configure the dynamic MAC address entry.

Choose the menu Switching→MAC Address→Dynamic Address to load the following page.

50

Figure 5-15 Dynamic Address

The following entries are displayed on this screen:

Aging Config

Auto Aging:

Aging Time:

Allows you to Enable/Disable the Auto Aging feature.

Enter the Aging Time for the dynamic address.

Search Option

Search Option: Select a Search Option from the pull-down list and click the Search button to find your desired entry in the Dynamic Address Table.

MAC: Enter the MAC address of your desired entry.

VLAN ID: Enter the VLAN ID number of your desired entry.

Port: Enter the Port number of your desired entry.

LAG ID: Enter the LAG ID of your desired entry.

Dynamic Address Table

Select:

MAC Address:

VLAN ID:

Port:

Type:

Aging Status:

Bind:

Select the entry to delete the dynamic address or to bind the MAC address to the corresponding port statically. It is multi-optional.

Displays the dynamic MAC Address.

Displays the corresponding VLAN ID of the MAC address.

Displays the corresponding port number of the MAC address.

Displays the Type of the MAC address.

Displays the Aging Status of the MAC address.

Click the Bind button to bind the MAC address of your selected entry to the corresponding port statically.

51

Tips:

Setting aging time properly helps implement effective MAC address aging. The aging time that is too long or too short results decreases the performance of the switch. If the aging time is too long, excessive invalid MAC address entries maintained by the switch may fill up the MAC address table.

This prevents the MAC address table from updating with network changes in time. If the aging time is too short, the switch may remove valid MAC address entries. This decreases the forwarding performance of the switch. It is recommended to keep the default value.

5.4.4 Filtering Address

The filtering address is to forbid the undesired packets to be forwarded. The filtering address can be added or removed manually, independent of the aging time. The filtering MAC address allows the switch to filter the packets which includes this MAC address as the source address or destination address, so as to guarantee the network security. The filtering MAC address entries act on all the ports in the corresponding VLAN.

Choose the menu Switching→MAC Address→Filtering Address to load the following page.

Figure 5-16 Filtering Address

The following entries are displayed on this screen:

Create Filtering Address

MAC Address:

VLAN ID:

Search Option

Search Option:

Enter the MAC Address to be filtered.

Enter the corresponding VLAN ID of the MAC address.

Select a Search Option from the pull-down list and click the Search button to find your desired entry in the Filtering Address Table.

MAC Address: Enter the MAC address of your desired entry.

VLAN ID: Enter the VLAN ID number of your desired entry.

52

 Filtering Address Table

Select:

MAC Address:

VLAN ID:

Port:

Type:

Aging Status:

Select the entry to delete the corresponding filtering address. It is multi-optional.

Displays the filtering MAC Address.

Displays the corresponding VLAN ID.

Here the symbol “--” indicates no specified port.

Displays the Type of the MAC address.

Displays the Aging Status of the MAC address.

Note:

The MAC address in the Filtering Address Table can not be added to the Static Address Table or bound to a port dynamically.

5.5 DHCP Filtering

Nowadays, the network is getting larger and more complicated. The amount of the PCs always exceeds that of the assigned IP addresses. The wireless network and the laptops are widely used and the locations of the PCs are always changed. Therefore, the corresponding IP address of the

PC should be updated with a few configurations. DHCP (Dynamic Host Configuration Protocol) functions to solve the above mentioned problems.

However, during the working process of DHCP, generally there is no authentication mechanism between Server and Client. If there are several DHCP servers in the network, network confusion and security problem will happen. To protect the switch from being attacked by illegal DHCP servers, you can configure the desired ports as trusted ports and only the clients connected to the trusted ports can receive DHCP packets from DHCP severs. Here the DHCP Filtering function performs to monitor the process of hosts obtaining IP addresses from DHCP servers.

 DHCP Working Principle

DHCP works via the “Client/Server” communication mode. The Client applies to the Server for configuration. The Server assigns the configuration information, such as the IP address, to the

Client, so as to reach a dynamic employ of the network source. A Server can assign IP address for several Clients, which is illustrated in the following figure.

53

Figure 5-17 Network diagram of DHCP

For different DHCP clients, DHCP server provides three IP address assigning methods:

(1) Manually assign the IP address: Allows the administrator to bind the static IP address to a specific client (e.g.: WWW Server) via the DHCP server.

(2) Automatically assign the IP address: DHCP server assigns the IP address without an expiry time limitation to the clients.

(3) Dynamically assign the IP address: DHCP server assigns the IP address with an expiry time. When the time for the IP address expired, the client should apply for a new one.

Most clients obtain IP addresses dynamically, which is illustrated in the following figure.

Figure 5-18 Interaction between a DHCP client and a DHCP server

( 1) DHCP-DISCOVER Stage: The Client broadcasts the DHCP-DISCOVER packet to find the DHCP server.

( 2) DHCP-OFFER Stage: Upon receiving the DHCP-DISCOVER packet, the DHCP server selects an IP address from the IP pool according to the assigning priority of the IP

54

addresses and replies to the client with DHCP-OFFER packet carrying the IP address and other information.

( 3) DHCP-REQUEST Stage: In the situation that there are several DHCP servers sending the

DHCP-OFFER packets, the client will only respond to the first received DHCP-OFFER packet and broadcast the DHCP-REQUEST packet which includes the assigned IP address of the DHCP-OFFER packet.

( 4) DHCP-ACK Stage: Since the DHCP-REQUEST packet is broadcasted, all DHCP servers on the network segment can receive it. However, only the requested server processes the request. If the DHCP server acknowledges assigning this IP address to the client, it will send the DHCP-ACK packet back to the client. Otherwise, the Server will send the

DHCP-NAK packet to refuse assigning this IP address to the client.

 DHCP Cheating Attack

During the working process of DHCP, generally there is no authentication mechanism between

Server and Client. If there are several DHCP servers in the network, network confusion and security problem will happen. The common cases incurring the illegal DHCP servers are the following two:

( 1) It’s common that the illegal DHCP server is manually configured by the user by mistake.

( 2) Hacker exhausted the IP addresses of the normal DHCP server and then pretended to be a legal DHCP server to assign the IP addresses and the other parameters to Clients. For example, hacker used the pretended DHCP server to assign a modified DNS server address to users so as to induce the users to the evil financial website or electronic trading website and cheat the users of their accounts and passwords. The following figure illustrates the DHCP Cheating Attack implementation procedure.

Figure 5-19 DHCP Cheating Attack Implementation Procedure

DHCP Filtering feature allows only the trusted ports to forward DHCP packets and thereby ensures that users get proper IP addresses. DHCP Filtering is to monitor the process of hosts obtaining the IP addresses from DHCP servers, and record the IP address, MAC address, VLAN and the connected Port number of the Host for automatic binding. DHCP Filtering feature prevents

55

the network from the DHCP Server Cheating Attack by discarding the DHCP packets on the distrusted port, so as to enhance the network security.

Choose the menu Switching → DHCP Filtering to load the following page.

Figure 5-20 DHCP Filtering

The following entries are displayed on this screen :

DHCP Filtering

DHCP Filtering:

Enable/Disable the DHCP Filtering function globally.

Trusted Port

Here you can select the desired port(s) to be Trusted Port(s). Only the Trusted Port(s) can receive DHCP packets from DHCP Servers. Click All button to select all ports. Click Clear button to select none.

Return to CONTENTS

56

Chapter 6 VLAN

The traditional Ethernet is a data network communication technology based on CSMA/CD (Carrier

Sense Multiple Access/Collision Detect) via shared communication medium. Through the traditional Ethernet, the overfull hosts in LAN will result in serious collision, flooding broadcasts, poor performance or even breakdown of the Internet. Though connecting the LANs through switches can avoid the serious collision, the flooding broadcasts can not be prevented, which will occupy plenty of bandwidth resources, causing potential serious security problems.

A Virtual Local Area Network (VLAN) is a network topology configured according to a logical scheme rather than the physical layout. The VLAN technology is developed for switches to control broadcast in LANs. By creating VLANs in a physical LAN, you can divide the LAN into multiple logical LANs, each of which has a broadcast domain of its own. Hosts in the same VLAN communicate with one another as if they are in a LAN. However, hosts in different VLANs cannot communicate with one another directly. Therefore, broadcast packets are limited in a VLAN. Hosts in the same VLAN communicate with one another via Ethernet whereas hosts in different VLANs communicate with one another through the Internet devices such as router, the Layer 3 switch, etc.

The following figure illustrates a VLAN implementation.

Figure 6-1 VLAN implementation

Compared with the traditional Ethernet, VLAN enjoys the following advantages.

( 1) Broadcasts are confined to VLANs. This decreases bandwidth utilization and improves network performance.

( 2) Network security is improved. VLANs cannot communicate with one another directly. That is, a host in a VLAN cannot access resources in another VLAN directly, unless routers or

Layer 3 switches are used.

( 3) Network configuration workload for the host is reduced. VLAN can be used to group specific hosts. When the physical position of a host changes within the range of the VLAN, you do not need to change its network configuration.

A VLAN can span across multiple switches, or even routers. This enables hosts in a VLAN to be dispersed in a looser way. That is, hosts in a VLAN can belong to different physical network segments. This switch supports 802.1Q VLAN to classify VLANs. VLAN tags in the packets are necessary for the switch to identify packets of different VLANs.

57

6.1 802.1Q VLAN

VLAN tags in the packets are necessary for the switch to identify packets of different VLANs. The switch works at the data link layer in OSI model and it can identify the data link layer encapsulation of the packet only, so you can add the VLAN tag field into the data link layer encapsulation for identification.

In 1999, IEEE issues the IEEE 802.1Q protocol to standardize VLAN implementation, defining the structure of VLAN-tagged packets. IEEE 802.1Q protocol defines that a 4-byte VLAN tag is encapsulated after the destination MAC address and source MAC address to show the information about VLAN.

As shown in the following figure, a VLAN tag contains four fields, including TPID (Tag Protocol

Identifier), Priority, CFI (Canonical Format Indicator), and VLAN ID.

Figure 6-2 Format of VLAN Tag

( 1) TPID: TPID is a 16-bit field, indicating that this data frame is VLAN-tagged. By default, it is

0x8100 in this switch.

( 2) Priority: Priority is a 3-bit field, referring to 802.1p priority. Refer to section “QoS & QoS profile” for details.

( 3) CFI: CFI is a 1-bit field, indicating whether the MAC address is encapsulated in the standard format in different transmission media. This field is not described in detail in this chapter.

( 4) VLAN ID: VLAN ID is a 12-bit field, indicating the ID of the VLAN to which this packet belongs. It is in the range of 0 to 4,095. Generally, 0 and 4,095 is not used, so the field is in the range of 1 to 4,094.

VLAN ID identifies the VLAN to which a packet belongs. When the switch receives an un-VLAN-tagged packet, it will encapsulate a VLAN tag with the default VLAN ID of the inbound port for the packet, and the packet will be assigned to the default VLAN of the inbound port for transmission.

In this User Guide, the tagged packet refers to the packet with VLAN tag whereas the untagged packet refers to the packet without VLAN tag, and the priority-tagged packet refers to the packet with VLAN tag whose VLAN ID is 0.

Link Types of ports

When creating the 802.1Q VLAN, you should set the link type for the port according to its connected device. The link types of port including the following two types: Untagged and Tagged.

( 1) Untagged: The untagged port can be added in multiple VLANs. If a VLAN-tagged packet arrives at a port and the VLAN ID in its VLAN tag does not match any of the VLAN the ingress port belongs to, this packet will be dropped. The packets forwarded by the untagged port are untagged.

( 2) Tagged: The tagged port can be added in multiple VLANs. If a VLAN-tagged packet arrives at a port and the VLAN ID in its VLAN tag does not match any of the VLAN the ingress port belongs to, this packet will be dropped. When the VLAN-tagged packets are forwarded by the Tagged port, its VLAN tag will not be changed.

58

 PVID

PVID (Port VLAN ID) is the default VID of the port. When the switch receives an un-VLAN-tagged packet, it will add a VLAN tag to the packet according to the PVID of its received port and forward the packets.

When creating VLANs, the PVID of each port, indicating the default VLAN to which the port belongs, is an important parameter with the following two purposes:

( 1) When the switch receives an un-VLAN-tagged packet, it will add a VLAN tag to the packet according to the PVID of its received port

( 2) PVID determines the default broadcast domain of the port, i.e. when the port receives UL packets or broadcast packets, the port will broadcast the packets in its default VLAN.

Different packets, tagged or untagged, will be processed in different ways, after being received by ports of different link types, which is illustrated in the following table.

Port Type

Untagged

Packets

Receiving Packets

Tagged Packets

Forwarding Packets

Untagged Packets

Tagged

Packets

Untagged

Tagged

When untagged

If the VID of packet packets are received, the port will add the port, the packet will be received. default VLAN tag, i.e. the PVID of the ingress port, to the packets.

If the VID of packet is forbidden by the port, the packet will be dropped.

The packet will be forwarded unchanged.

The packet will be forwarded with the

PVID of egress port as its VLAN tag.

The packet will be forwarded after removing its VLAN tag

The packet will be forwarded with its current

VLAN tag.

Table 6-1 Relationship between Port Types and VLAN Packets Processing

IEEE 802.1Q VLAN function is implemented on the VLAN Config pages.

6.1.1 VLAN Config

On this page, you can configure the 802.1Q VLAN and its ports.

Choose the menu VLAN→802.1Q VLAN→VLAN Config to load the following page.

59

Figure 6-3 VLAN Table

To ensure the normal communication of the factory switch, the default VLAN of all ports is set to

VLAN1.

The following entries are displayed on this screen:

VLAN Create

VLAN ID

Name

VLAN Table

Enter the VLAN ID you want to create. It ranges from 2 to 4094.

Give a name to the VLAN for identification.

VLAN ID Select: Click based on the VLAN ID you entered.

Select:

VLAN ID:

Select the desired port for configuration.

Displays the VLAN ID.

Name:

Untagged Ports:

Tagged Ports:

Operation:

Displays the name of the specific VLAN.

Show the untagged ports of the specific VLAN.

Show the tagged ports of the specific VLAN.

You can delete the specific VLAN when you click the word

"Delete".

VLAN Membership

VLAN ID:

VLAN Name:

Displays the VLAN ID you choose.

Here you can set the name of the VLAN you choose.

60

Port:

Untagged:

Tagged:

NotMember:

PVID:

LAG:

Displays the port number.

The port will be an untagged member of the specific VLAN if you select it.

The port will be an tagged member of the specific VLAN if you select it.

The port will not be a member of the specific VLAN if you select it.

Here you can change the PVID of the specific port.

Displays the LAG to which the port belongs to.

6.2 Application Example for 802.1Q VLAN

Network Requirements

Switch A is connecting to PC A and Server B;

Switch B is connecting to PC B and Server A;

 PC A and Server A is in the same VLAN;

PC B and Server B is in the same VLAN;

PCs in the two VLANs cannot communicate with each other.

Network Diagram

Configuration Procedure

Configure Switch A

Step Operation Description

Link Type of the

Required. On VLAN→802.1Q VLAN→VLAN Config page, configure the link type of Port 2, Port 3 and Port 4 as Untagged, Tagged and ports

Untagged respectively

Required.

VLAN with its VLAN ID as 10, owning Port 2 and Port 3.

Required.

VLAN with its VLAN ID as 20, owning Port 3 and Port 4.

61

 Configure Switch B

Step Operation Description

Link Type of the ports the link type of Port 7, Port 6 and Port 8 as Untagged, Tagged and

Untagged respectively.

VLAN with its VLAN ID as 10, owning Port 6 and Port 8.

VLAN with its VLAN ID as 20, owning Port 6 and Port 7.

Return to CONTENTS

62

Chapter 7 Spanning Tree

STP (Spanning Tree Protocol), subject to IEEE 802.1D standard, is to disbranch a ring network in the Data Link layer in a local network. Devices running STP discover loops in the network and block ports by exchanging information, in that way, a ring network can be disbranched to form a tree-topological ring-free network to prevent packets from being duplicated and forwarded endlessly in the network.

BPDU (Bridge Protocol Data Unit) is the protocol data that STP and RSTP use. Enough information is carried in BPDU to ensure the spanning tree generation. STP is to determine the topology of the network via transferring BPDUs between devices.

To implement spanning tree function, the switches in the network transfer BPDUs between each other to exchange information and all the switches supporting STP receive and process the received BPDUs. BPDUs carry the information that is needed for switches to figure out the spanning tree.

STP Elements

Bridge ID(Bridge Identifier): Indicates the value of the priority and MAC address of the bridge.

Bridge ID can be configured and the switch with the lower bridge ID has the higher priority.

Root Bridge: Indicates the switch has the lowest bridge ID. Configure the best PC in the ring network as the root bridge to ensure best network performance and reliability.

Designated Bridge: Indicates the switch has the lowest path cost from the switch to the root bridge in each network segment. BPDUs are forwarded to the network segment through the designated bridge. The switch with the lowest bridge ID will be chosen as the designated bridge.

Root Path Cost: Indicates the sum of the path cost of the root port and the path cost of all the switches that packets pass through. The root path cost of the root bridge is 0.

Bridge Priority: The bridge priority can be set to a value in the range of 0~32768. The lower value priority has the higher priority. The switch with the higher priority has more chance to be chosen as the root bridge.

Root Port: Indicates the port that has the lowest path cost from this bridge to the Root Bridge and forwards packets to the root.

Designated Port: Indicates the port that forwards packets to a downstream network segment or switch.

Port Priority: The port priority can be set to a value in the range of 0~255. The lower value priority has the higher priority. The port with the higher priority has more chance to be chosen as the root port.

Path Cost: Indicates the parameter for choosing the link path by STP. By calculating the path cost,

STP chooses the better links and blocks the redundant links so as to disbranch the ring-network to form a tree-topological ring-free network.

The following network diagram shows the sketch map of spanning tree. Switch A, B and C are connected together in order. After STP generation, switch A is chosen as root bridge, the path from port 2 to port 6 is blocked.

Bridge: Switch A is the root bridge in the whole network; switch B is the designated bridge of switch C.

Port: Port 3 is the root port of switch B and port 5 is the root port of switch C; port 1 is the designated port of switch A and port 4 is the designated port of switch B; port 6 is the blocked port of switch C.

63

Figure 7-1 Basic STP diagram

 STP Timers

Hello Time:

Hello Time ranges from 1 to 10 seconds. It specifies the interval to send BPDU packets. It is used to test the links.

Max. Age:

Max. Age ranges from 6 to 40 seconds. It specifies the maximum time the switch can wait without receiving a BPDU before attempting to reconfigure.

Forward Delay:

Forward Delay ranges from 4 to 30 seconds. It specifies the time for the port to transit its state after the network topology is changed.

When the STP regeneration caused by network malfunction occurs, the STP structure will get some corresponding change. However, as the new configuration BPDUs cannot be spread in the whole network at once, the temporal loop will occur if the port transits its state immediately.

Therefore, STP adopts a state transit mechanism, that is, the new root port and the designated port begins to forward data after twice forward delay, which ensures the new configuration BPDUs are spread in the whole network.

BPDU Comparing Principle in STP mode

Assuming two BPDUs: BPDU X and BPDU Y

If the root bridge ID of X is smaller than that of Y, X is superior to Y.

If the root bridge ID of X equals that of Y, but the root path cost of X is smaller than that of Y, X is superior to Y.

If the root bridge ID and the root path cost of X equal those of Y, but the bridge ID of X is smaller than that of Y, X is superior to Y.

If the root bridge ID, the root path cost and bridge ID of X equal those of Y, but the port ID of X is smaller than that of Y, X is superior to Y.

 STP Generation

In the beginning

In the beginning, each switch regards itself as the root, and generates a configuration BPDU for each port on it as a root, with the root path cost being 0, the ID of the designated bridge being that of the switch, and the designated port being itself.

64

 Comparing BPDUs

Each switch sends out configuration BPDUs and receives a configuration BPDU on one of its ports from another switch. The following table shows the comparing operations.

Step Operation

1

2

If the priority of the BPDU received on the port is lower than that of the BPDU if of the port itself, the switch discards the BPDU and does not change the BPDU of the port.

If the priority of the BPDU is higher than that of the BPDU of the port itself, the switch replaces the BPDU of the port with the received one and compares it with those of other ports on the switch to obtain the one with the highest priority.

Table 7-1 Comparing BPDUs

Selecting the root bridge

The root bridge is selected by BPDU comparing. The switch with the smallest root ID is chosen as the root bridge.

 Selecting the root port and designate port

The operation is taken in the following way:

Step Operation

1 For each switch (except the one chosen as the root bridge) in a network, the port that receives the BPDU with the highest priority is chosen as the root port of the switch.

2 Using the root port BPDU and the root path cost, the switch generates a designated port BPDU for each of its ports.

Root ID is replaced with that of the root port;

Root path is replaced with the sum of the root path cost of the root port and the path cost between this port and the root port;

The ID of the designated bridge is replaced with that of the switch;

The ID of the designated port is replaced with that of the port.

3 The switch compares the resulting BPDU with the BPDU of the desired port whose role you want to determine.

If the resulting BPDU takes the precedence over the BPDU of the port, the port is chosen as the designated port and the BPDU of this port is replaced with the resulting BPDU. The port regularly sends out the resulting BPDU;

If the BPDU of this port takes the precedence over the resulting BPDU, the

BPDU of this port is not replaced and the port is blocked. The port only can receive BPDUs.

Table 7-2 Selecting root port and designated port

Tips

In a STP with stable topology, only the root port and designated port can forward data, and the other ports are blocked. The blocked ports only can receive BPDUs.

RSTP (Rapid Spanning Tree Protocol), evolved from the 802.1D STP standard, enable Ethernet ports to transit their states rapidly. The premises for the port in the RSTP to transit its state rapidly are as follows.

65

 The condition for the root port to transit its port state rapidly: The old root port of the switch stops forwarding data and the designated port of the upstream switch begins to forward data.

The condition for the designated port to transit its port state rapidly: The designated port is an edge port or connecting to a point-to-point link. If the designated port is an edge port, it can directly transit to forwarding state; if the designated port is connecting to a point-to-point link, it can transit to forwarding state after getting response from the downstream switch through handshake.

RSTP Elements

Edge Port: Indicates the port connected directly to terminals.

P2P Link: Indicates the link between two switches directly connected.

MSTP (Multiple Spanning Tree Protocol), compatible with both STP and RSTP and subject to IEEE

802.1s standard, not only enables spanning trees to converge rapidly, but also enables packets of different VLANs to be forwarded along their respective paths so as to provide redundant links with a better load-balancing mechanism.

Features of MSTP:

 MSTP combines VLANs and spanning tree together via VLAN-to-instance mapping table. It binds several VLANs to an instance to save communication cost and network resources.

MSTP divides a spanning tree network into several regions. Each region has several internal spanning trees, which are independent of each other.

MSTP provides a load-balancing mechanism for the packets transmission in the VLAN.

 MSTP is compatible with both STP and RSTP.

 MSTP Elements

MST Region (Multiple Spanning Tree Region): An MST Region comprises switches with the same region configuration and VLAN-to-Instances mapping relationship.

IST (Internal Spanning Tree): An IST is a spanning tree in an MST.

CST (Common Spanning Tree): A CST is the spanning tree in a switched network that connects all

MST regions in the network.

CIST (Common and Internal Spanning Tree): A CIST, comprising IST and CST, is the spanning tree in a switched network that connects all switches in the network.

The following figure shows the network diagram in MSTP.

66

Figure 7-2 Basic MSTP diagram

MSTP

MSTP divides a network into several MST regions. The CST is generated between these MST regions, and multiple spanning trees can be generated in each MST region. Each spanning tree is called an instance. As well as STP, MSTP uses BPDUs to generate spanning tree. The only difference is that the BPDU for MSTP carries the MSTP configuration information on the switches.

Port States

In an MSTP, ports can be in the following four states:

 Forwarding: In this status the port can receive/forward data, receive/send BPDU packets as well as learn MAC address.

 Learning: In this status the port can receive/send BPDU packets and learn MAC address.

 Blocking: In this status the port can only receive BPDU packets.

 Disconnected: In this status the port is not participating in the STP.

Port Roles

In an MSTP, the following roles exist:

 Root Port: Indicates the port that has the lowest path cost from this bridge to the Root Bridge and forwards packets to the root.

 Designated Port: Indicates the port that forwards packets to a downstream network segment or switch.

 Master Port: Indicates the port that connects a MST region to the common root. The path from the master port to the common root is the shortest path between this MST region and the common root.

 Alternate Port: Indicates the port that can be a backup port of a root or master port.

 Backup Port: Indicates the port that is the backup port of a designated port.

 Disabled: Indicates the port that is not participating in the STP.

The following diagram shows the different port roles.

67

Figure 7-3 Port roles

The Spanning Tree module is mainly for spanning tree configuration of the switch, including four submenus: STP Config, Port Config, MSTP Instance and STP Security.

7.1 STP Config

The STP Config function, for global configuration of spanning trees on the switch, can be implemented on STP Config and STP Summary pages.

7.1.1 STP Config

Before configuring spanning trees, you should make clear the roles each switch plays in each spanning tree instance. Only one switch can be the root bridge in each spanning tree instance. On this page you can globally configure the spanning tree function and related parameters.

Choose the menu Spanning Tree→STP Config→STP Config to load the following page.

Figure 7-4 STP Config

68

The following entries are displayed on this screen:

Global Config

STP:

Version:

Select Enable/Disable STP function globally on the switch.

Select the desired STP version on the switch.

 STP:

 RSTP: Rapid Spanning Tree Protocol.

 MSTP: Multiple Spanning Tree Protocol.

 Parameters Config

CIST Priority:

Hello Time

Max Age:

Forward Delay:

TxHold Count:

Max Hops:

Enter a value from 0 to 61440 to specify the priority of the switch for comparison in the CIST. CIST priority is an important criterion on determining the root bridge. In the same condition, the switch with the highest priority will be chosen as the root bridge. The lower value has the higher priority. The default value is 32768 and should be exact divisor of 4096.

Enter a value from 1 to 10 in seconds to specify the interval to send BPDU packets. It is used to test the links. 2*(Hello Time + 1)

≤ Max Age. The default value is 2 seconds.

Enter a value from 6 to 40 in seconds to specify the maximum time the switch can wait without receiving a BPDU before attempting to reconfigure. The default value is 20 seconds.

Enter a value from 4 to 30 in seconds to specify the time for the port to transit its state after the network topology is changed.

2*(Forward Delay-1) ≥ Max Age. The default value is 15 seconds.

Enter a value from 1 to 20 to set the maximum number of BPDU packets transmitted per Hello Time interval. The default value is

5pps.

Enter a value from 1 to 40 to set the maximum number of hops that occur in a specific region before the BPDU is discarded. The default value is 20 hops.

Note:

1. The forward delay parameter and the network diameter are correlated. A too small forward delay parameter may result in temporary loops. A too large forward delay may cause a network unable to resume the normal state in time. The default value is recommended.

2. An adequate hello time parameter can enable the switch to discover the link failures occurred in the network without occupying too much network resources. A too large hello time parameter may result in normal links being regarded as invalid when packets drop occurred in the links, which in turn result in spanning tree being regenerated. A too small hello time parameter may result in duplicated configuration being sent frequently, which increases the network load of the switches and wastes network resources. The default value is recommended.

3. A too small max age parameter may result in the switches regenerating spanning trees frequently and cause network congestions to be falsely regarded as link problems. A too large max age parameter result in the switches unable to find the link problems in time, which in turn handicaps spanning trees being regenerated in time and makes the network less adaptive. The default value is recommended.

4. If the TxHold Count parameter is too large, the number of MSTP packets being sent in each hello time may be increased with occupying too much network resources. The default value is recommended.

69

7.1.2 STP Summary

On this page you can view the related parameters for Spanning Tree function.

Choose the menu Spanning Tree→STP Config→STP Summary to load the following page.

Figure 7-5 STP Summary

7.2 Port Config

On this page you can configure the parameters of the ports for CIST

Choose the menu Spanning Tree→Port Config to load the following page.

70

Figure 7-6 Port Config

The following entries are displayed on this screen:

Port Config

Port Select:

Select:

Port:

Status:

Priority:

ExtPath:

IntPath:

Edge Port:

P2P Link:

MCheck:

STP Version:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for STP configuration. It is multi-optional.

Displays the port number of the switch.

Select Enable /Disable STP function for the desired port.

Enter a value from 0 to 240 divisible by 16. Port priority is an important criterion on determining if the port connected to this port will be chosen as the root port. The lower value has the higher priority.

ExtPath Cost is used to choose the path and calculate the path costs of ports in different MST regions. It is an important criterion on determining the root port. The lower value has the higher priority.

IntPath Cost is used to choose the path and calculate the path costs of ports in an MST region. It is an important criterion on determining the root port. The lower value has the higher priority.

Select Enable/Disable Edge Port. The edge port can transit its state from blocking to forwarding rapidly without waiting for forward delay.

Select the P2P link status. If the two ports in the P2P link are root port or designated port, they can transit their states to forwarding rapidly to reduce the unnecessary forward delay.

Select Enable to perform MCheck operation on the port. Unchange means no MCheck operation.

Displays the STP version of the port.

71

Port Role:

Port Status:

LAG:

Displays the role of the port played in the STP Instance.

 Root Port: Indicates the port that has the lowest path cost from this bridge to the Root Bridge and forwards packets to the root.

 Designated Port: Indicates the port that forwards packets to a downstream network segment or switch.

 Master Port: Indicates the port that connects a MST region to the common root. The path from the master port to the common root is the shortest path between this MST region and the common root.

 Alternate Port: Indicates the port that can be a backup port of a root or master port.

 Backup Port: Indicates the port that is the backup port of a designated port.

 Disabled: Indicates the port that is not participating in the STP.

Displays the working status of the port.

 Forwarding: In this status the port can receive/forward data, receive/send BPDU packets as well as learn MAC address.

 Learning: In this status the port can receive/send BPDU packets and learn MAC address.

 Blocking: In this status the port can only receive BPDU packets.

 Disconnected: In this status the port is not participating in the

STP.

Displays the LAG number which the port belongs to.

Note:

1. Configure the ports connected directly to terminals as edge ports and enable the BPDU protection function as well. This not only enables these ports to transit to forwarding state rapidly but also secures your network.

2. All the links of ports in a LAG can be configured as point-to-point links.

3. When the link of a port is configured as a point-to-point link, the spanning tree instances owning this port are configured as point-to-point links. If the physical link of a port is not a point-to-point link and you forcibly configure the link as a point-to-point link, temporary loops may be incurred.

7.3 MSTP Instance

MSTP combines VLANs and spanning tree together via VLAN-to-instance mapping table

(VLAN-to-spanning-tree mapping). By adding MSTP instances, it binds several VLANs to an instance to realize the load balance based on instances.

Only when the switches have the same MST region name, MST region revision and

VLAN-to-Instance mapping table, the switches can be regarded as in the same MST region.

The MSTP Instance function can be implemented on Region Config, Instance Config and

Instance Port Config pages.

7.3.1 Region Config

On this page you can configure the name and revision of the MST region

Choose the menu Spanning Tree→MSTP Instance→Region Config to load the following page.

72

Figure 7-7 Region Config

The following entries are displayed on this screen:

Region Config

Region Name:

Revision:

Create a name for MST region identification using up to 32 characters.

Enter the revision from 0 to 65535 for MST region identification.

7.3.2 Instance Config

Instance Configuration, a property of MST region, is used to describe the VLAN to Instance mapping configuration. You can assign VLAN to different instances appropriate to your needs.

Every instance is a VLAN group independent of other instances and CIST.

Choose the menu Spanning Tree→MSTP Instance→Instance Config to load the following page.

Figure 7-8 Instance Config

73

The following entries are displayed on this screen:

Instance Table

Instance ID Select: Click the Select button to quick-select the corresponding Instance ID based on the ID number you entered.

Select: Select the desired Instance ID for configuration. It is multi-optional.

Instance:

Status:

Priority:

Displays Instance ID of the switch.

Displays status of the instance.

VLAN ID:

Clear:

Enter the priority of the switch in the instance. It is an important criterion on determining if the switch will be chosen as the root bridge in the specific instance.

Enter the VLAN ID which belongs to the corresponding instance ID.

After modification here, the previous VLAN ID will be cleared and mapped to the CIST.

Click the Clear button to clear up all VLAN IDs from the instance ID.

The cleared VLAN ID will be automatically mapped to the CIST.

VLAN-Instance Mapping

VLAN ID:

Instance ID:

Enter the desired VLAN ID. After modification here, the new VLAN ID will be added to the corresponding instance ID and the previous

VLAN ID won’t be replaced.

Enter the corresponding instance ID.

7.3.3 Instance Port Config

A port can play different roles in different spanning tree instance. On this page you can configure the parameters of the ports in different instance IDs as well as view status of the ports in the specified instance.

Choose the menu Spanning Tree→MSTP Instance→Instance Port Config to load the following page.

74

Figure 7-9 Instance Port Config

The following entries are displayed on this screen:

 Port Config

Instance ID:

Port Select:

Select:

Port:

Priority:

Path Cost:

Port Role:

Port Status:

LAG:

Select the desired instance ID for its port configuration.

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port to specify its priority and path cost. It is multi-optional.

Displays the port number of the switch.

Enter the priority of the port in the instance. It is an important criterion on determining if the port connected to this port will be chosen as the root port.

Path Cost is used to choose the path and calculate the path costs of ports in an MST region. It is an important criterion on determining the root port. The lower value has the higher priority.

Displays the role of the port played in the MSTP Instance.

Displays the working status of the port.

Displays the LAG number which the port belongs to.

Note:

The port status of one port in different spanning tree instances can be different.

Global configuration Procedure for Spanning Tree function:

75

Step Operation

1 Make clear roles the switches instances: root bridge or designated bridge

Description

Preparation. play in spanning tree parameters and configure MSTP parameters on Spanning

Tree→STP Config→STP Config page.

4 for ports

Configure the MST region

Spanning Tree→Port Config→Port Config page.

Required. Create MST region and configure the role the switch plays in the MST region on Spanning

Tree→MSTP Instance→Region Config and Instance

Config page. for instance ports and configure MSTP parameters for instance ports on

Spanning Tree→MSTP Instance→Instance Port

Config page.

7.4 STP Security

Configuring protection function for devices can prevent devices from any malicious attack against

STP features. The STP Security function can be implemented on Port Protect and TC Protect pages.

Port Protect function is to prevent the devices from any malicious attack against STP features.

7.4.1 Port Protect

On this page you can configure loop protect feature, root protect feature, TC protect feature,

BPDU protect feature and BPDU filter feature for ports. You are suggested to enable corresponding protection feature for the qualified ports.

Loop Protect

In a stable network, a switch maintains the states of ports by receiving and processing BPDU packets from the upstream switch. However, when link congestions or link failures occurred to the network, a down stream switch does not receive BPDU packets for certain period, which results in spanning trees being regenerated and roles of ports being reselected, and causes the blocked ports to transit to forwarding state. Therefore, loops may be incurred in the network.

The loop protect function can suppresses loops. With this function enabled, a port, regardless of the role it plays in instances, is always set to blocking state, when the port does not receive BPDU packets from the upstream switch and spanning trees are regenerated, and thereby loops can be prevented.

Root Protect

A CIST and its secondary root bridges are usually located in the high-bandwidth core region.

Wrong configuration or malicious attacks may result in configuration BPDU packets with higher priorities being received by the legal root bridge, which causes the current legal root bridge to lose its position and network topology jitter to occur. In this case, flows that should travel along high-speed links may lead to low-speed links, and network congestion may occur.

76

To avoid this, MSTP provides root protect function. Ports with this function enabled can only be set as designated ports in all spanning tree instances. When a port of this type receives BDPU packets with higher priority, it transits its state to blocking state and stops forwarding packets (as if it is disconnected from the link). The port resumes the normal state if it does not receive any configuration BPDU packets with higher priorities for a period of two times of forward delay.

 TC Protect

A switch removes MAC address entries upon receiving TC-BPDU packets. If a user maliciously sends a large amount of TC-BPDU packets to a switch in a short period, the switch will be busy with removing MAC address entries, which may decrease the performance and stability of the network.

To prevent the switch from frequently removing MAC address entries, you can enable the TC protect function on the switch. With TC protect function enabled, if the account number of the received TC-BPDUs exceeds the maximum number you set in the TC threshold field, the switch will not performs the removing operation in the TC protect cycle. Such a mechanism prevents the switch from frequently removing MAC address entries.

 BPDU Protect

Ports of the switch directly connected to PCs or servers are configured as edge ports to rapidly transit their states. When these ports receive BPDUs, the system automatically configures these ports as non-edge ports and regenerates spanning trees, which may cause network topology jitter.

Normally these ports do not receive BPDUs, but if a user maliciously attacks the switch by sending

BPDUs, network topology jitter occurs.

To prevent this attack, MSTP provides BPDU protect function. With this function enabled on the switch, the switch shuts down the edge ports that receive BPDUs and reports these cases to the administrator. If a port is shut down, only the administrator can restore it.

BPDU Filter

BPDU filter function is to prevent BPDUs flood in the STP network. If a switch receives malicious

BPDUs, it forwards these BPDUs to the other switched in the network, which may result in spanning trees being continuously regenerated. In this case, the switch occupying too much CPU or the protocol status of BPDUs is wrong.

With BPDU filter function enabled, a port does not receive or forward BPDUs, but it sends out its own BPDUs. Such a mechanism prevents the switch from being attacked by BPDUs so as to guarantee generation the spanning trees correct.

Choose the menu Spanning Tree→STP Security→Port Protect to load the following page.

77

Figure 7-10 Port Protect

The following entries are displayed on this screen:

 Port Protect

Port Select:

Select:

Port:

Loop Protect:

Root Protect:

TC Protect:

BPDU Protect:

BPDU Filter:

LAG:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for port protect configuration. It is multi-optional.

Displays the port number of the switch.

Loop Protect is to prevent the loops in the network brought by recalculating STP because of link failures and network congestions.

Root Protect is to prevent wrong network topology change caused by the role change of the current legal root bridge.

TC Protect is to prevent the decrease of the performance and stability of the switch brought by continuously removing MAC address entries upon receiving TC-BPDUs in the STP network.

BPDU Protect is to prevent the edge port from being attacked by maliciously created BPDUs

BPDU Filter is to prevent BPDUs flood in the STP network.

Displays the LAG number which the port belongs to.

7.4.2 TC Protect

When TC Protect is enabled for the port on Port Protect page, the TC threshold and TC protect cycle need to be configured on this page.

78

Choose the menu Spanning Tree→STP Security→TC Protect to load the following page.

Figure 7-11 TC Protect

The following entries are displayed on this screen:

 TC Protect

TC Threshold:

TC Protect Cycle:

Enter a number from 1 to 100. It is the maximum number of the

TC-BPDUs received by the switch in a TC Protect Cycle. The default value is 20.

Enter a value from 1 to 10 to specify the TC Protect Cycle. The default value is 5.

7.5 Application Example for STP Function

Network Requirements

Switch A, B, C, D and E all support MSTP function.

A is the central switch.

 B and C are switches in the convergence layer. D, E and F are switches in the access layer.

 There are 6 VLANs labeled as VLAN101-VLAN106 in the network.

 All switches run MSTP and belong to the same MST region.

The data in VLAN101, 103 and 105 are transmitted in the STP with B as the root bridge. The data in VLAN102, 104 and 106 are transmitted in the STP with C as the root bridge.

Network Diagram

79

 Configuration Procedure

Configure Switch A:

Step Operation Description type of the related ports as Tagged, and add the ports to VLAN101-VLAN106. The detailed instructions can be found in the section

802.1Q VLAN

. enable STP function and select MSTP version.

On Spanning Tree→STP Config→Port Config page, enable MSTP function for the port.

3 Configure the region name and the revision of MST region

On Spanning Tree→MSTP Instance→Region

Config page, configure the region as TP-LINK and keep the default revision setting. mapping table of the MST region Config page, configure VLAN-to-Instance mapping table. Map VLAN 101, 103 and 105 to Instance 1; map

VLAN 102, 104 and 106 to Instance 2.

Configure Switch B:

Step Operation Description type of the related ports as Tagged, and add the ports to VLAN101-VLAN106. The detailed instructions can be found in the section

802.1Q VLAN

. enable STP function and select MSTP version.

On Spanning Tree→STP Config→Port Config page, enable MSTP function for the port.

3 Configure the region name and the revision of MST region

On Spanning Tree→MSTP Instance→Region

Config page, configure the region as TP-LINK and keep the default revision setting. mapping table of the MST region Config page, configure VLAN-to-Instance mapping table. Map VLAN 101, 103 and 105 to Instance 1; map

VLAN 102, 104 and 106 to Instance 2.

5 Configure switch B as the root bridge of Instance 1

On Spanning Tree→MSTP Instance→Instance

Config page, configure the priority of Instance 1 to be

0.

6 Configure switch B as the On Spanning Tree→MSTP Instance→Instance designated bridge of Instance 2 Config page, configure the priority of Instance 2 to be

4096.

80

 Configure Switch C:

Step Operation Description type of the related ports as Tagged, and add the ports to VLAN101-VLAN106. The detailed instructions can be found in the section

802.1Q VLAN

. page, enable STP function and select MSTP version.

On Spanning Tree→STP Config→Port Config page, enable MSTP function for the port.

3 Configure the region name and the revision of MST region

On Spanning Tree→MSTP Instance→Region

Config page, configure the region as TP-LINK and keep the default revision setting. mapping table of the MST region Config page, configure VLAN-to-Instance mapping table. Map VLAN101, 103 and 105 to Instance 1; map

VLAN102, 104 and 106 to Instance 2.

5 Configure switch C as the root bridge of Instance 1

On Spanning Tree→MSTP Instance→Instance

Config page, configure the priority of Instance 1 to be

4096.

6 Configure switch C as the root bridge of Instance 2

On Spanning Tree→MSTP Instance→Instance

Config page, configure the priority of Instance 2 to be

0.

Configure Switch D:

Step Operation Description type of the related ports as Tagged, and add the ports to VLAN101-VLAN106. The detailed instructions can be found in the section

802.1Q VLAN

. page, enable STP function and select MSTP version.

On Spanning Tree→STP Config→Port Config page, enable MSTP function for the port.

3 Configure the region name and the revision of MST region

On Spanning Tree→MSTP Instance→Region

Config page, configure the region as TP-LINK and keep the default revision setting. mapping table of the MST region Config page, configure VLAN-to-Instance mapping table. Map VLAN101, 103 and 105 to Instance 1; map

VLAN102, 104 and 106 to Instance 2.

The configuration procedure for switch E and F is the same with that for switch D.

81

 The topology diagram of the two instances after the topology is stable

For Instance 1 (VLAN101, 103 and 105), the red paths in the following figure are connected links; the gray paths are the blocked links.

 For Instance 2 (VLAN102, 104 and 106), the blue paths in the following figure are connected links; the gray paths are the blocked links.

 Suggestion for Configuration

 Enable TC Protect function for all the ports of switches.

 Enable Root Protect function for all the ports of root bridges.

Enable Loop Protect function for the non-edge ports.

Enable BPDU Protect function or BPDU Filter function for the edge ports which are connected to the PC and server.

Return to CONTENTS

82

Chapter 8 Multicast

Multicast Overview

In the network, packets are sent in three modes: unicast, broadcast and multicast. In unicast, the source server sends separate copy information to each receiver. When a large number of users require this information, the server must send many pieces of information with the same content to the users. Therefore, large bandwidth will be occupied. In broadcast, the system transmits information to all users in a network. Any user in the network can receive the information, no matter the information is needed or not.

Point-to-multipoint multimedia business, such as video conferences and VoD (video-on-demand), plays an important part in the information transmission field. Suppose a point to multi-point service is required, unicast is suitable for networks with sparsely users, whereas broadcast is suitable for networks with densely distributed users. When the number of users requiring this information is not certain, unicast and broadcast deliver a low efficiency. Multicast solves this problem. It can deliver a high efficiency to send data in the point to multi-point service, which can save large bandwidth and reduce the network load. In multicast, the packets are transmitted in the following

way as shown in Figure 8-1.

Figure 8-1 Information transmission in the multicast mode

Features of multicast:

1. The number of receivers is not certain. Usually point-to-multipoint transmission is needed;

2. Multiple users receiving the same information form a multicast group. The multicast information sender just need to send the information to the network device once;

3. Each user can join and leave the multicast group at any time;

83

4. Real time is highly demanded and certain packets drop is allowed.

Multicast Address

As specified by IANA (Internet Assigned Numbers Authority), Class D IP addresses are used as destination addresses of multicast packets. The multicast IP addresses range from

224.0.0.0~239.255.255.255. The following table displays the range and description of several special multicast IP addresses.

Multicast IP address range Description

224.0.0.0~224.0.0.255 Reserved multicast addresses for routing protocols and other network protocols

224.0.1.0~224.0.1.255 Addresses for video conferencing

239.0.0.0~239.255.255.255 Local management multicast addresses, which are used in the local network only

Table 8-1 Range of the special multicast IP

When a unicast packet is transmitted in an Ethernet network, the destination MAC address is the

MAC address of the receiver. When a multicast packet is transmitted in an Ethernet network, the destination is not a receiver but a group with uncertain number of members, so a multicast MAC address, a logical MAC address, is needed to be used as the destination address.

As stipulated by IANA, the high-order 24 bits of a multicast MAC address begins with 01-00-5E while the low-order 23 bits of a multicast MAC address are the low-order 23 bits of the multicast IP

address. The mapping relationship is described as Figure 8-2.

Figure 8-2 Mapping relationship between multicast IP address and multicast MAC address

The high-order 4 bits of the IP multicast address are 1110, identifying the multicast group. Only 23 bits of the remaining low-order 28 bits are mapped to a multicast MAC address. In that way, 5 bits of the IP multicast address is not utilized. As a result, 32 IP multicast addresses are mapped to the same MAC addresses.

 Multicast Address Table

The switch is forwarding multicast packets based on the multicast address table. As the transmission of multicast packets can not span the VLAN, the first part of the multicast address table is VLAN ID, based on which the received multicast packets are forwarded in the VLAN owning the receiving port. The multicast address table is not mapped to an egress port but a group port list. When forwarding a multicast packet, the switch looks up the multicast address table based on the destination multicast address of the multicast packet. If the corresponding entry can not be found in the table, the switch will broadcast the packet in the VLAN owning the receiving port. If the corresponding entry can be found in the table, it indicates that the destination address should be a group port list, so the switch will duplicate this multicast data and deliver each port one

copy. The general format of the multicast address table is described as Figure 8-3 below.

84

VLAN ID Multicast IP Port

Figure 8-3 Multicast Address Table

 IGMP Snooping

In the network, the hosts apply to the near router for joining (leaving) a multicast group by sending

IGMP (Internet Group Management Protocol) messages. When the up-stream device forwards down the multicast data, the switch is responsible for sending them to the hosts. IGMP Snooping is a multicast control mechanism, which can be used on the switch for dynamic registration of the multicast group. The switch, running IGMP Snooping, manages and controls the multicast group via listening to and processing the IGMP messages transmitted between the hosts and the multicast router, thereby effectively prevents multicast groups being broadcasted in the network.

The Multicast module is mainly for multicast management configuration of the switch, including four submenus: IGMP Snooping, Multicast IP, Multicast Filter and Packet Statistics.

8.1 IGMP Snooping

IGMP Snooping Process

The switch, running IGMP Snooping, listens to the IGMP messages transmitted between the host and the router, and tracks the IGMP messages and the registered port. When receiving IGMP report message, the switch adds the port to the multicast address table; when the switch listens to

IGMP leave message from the host, the router sends the Group-Specific Query message of the port to check if other hosts need this multicast, if yes, the router will receive IGMP report message; if no, the router will receive no response from the hosts and the switch will remove the port from the multicast address table. The router regularly sends IGMP query messages. After receiving the

IGMP query messages, the switch will remove the port from the multicast address table if the switch receives no IGMP report message from the host within a period of time.

IGMP Messages

The switch, running IGMP Snooping, processes the IGMP messages of different types as follows.

1. IGMP Query Message

IGMP query message, sent by the router, falls into two types, IGMP general query message and

IGMP group-specific-query message. The router regularly sends IGMP general message to query if the multicast groups contain any member. When receiving IGMP leave message, the receiving port of the router will send IGMP group-specific-query message to the multicast group and the switch will forward IGMP group-specific-query message to check if other members in the multicast group of the port need this multicast.

When receiving IGMP general query message, the switch will forward them to all other ports in the

VLAN owning the receiving port. The receiving port will be processed: if the receiving port is not a router port yet, it will be added to the router port list with its router port time specified; if the receiving port is already a router port, its router port time will be directly reset.

When receiving IGMP group-specific-query message, the switch will send the group-specific query message to the members of the multicast group being queried.

2. IGMP Report Message

IGMP report message is sent by the host when it applies for joining a multicast group or responses to the IGMP query message from the router.

When receiving IGMP report message, the switch will send the report message via the router port in the VLAN as well as analyze the message to get the address of the multicast group the host applies for joining. The receiving port will be processed: if the receiving port is a new member port,

85

it will be added to the multicast address table with its member port time specified; if the receiving port is already a member port, its member port time will be directly reset.

3. IGMP Leave Message

The host, running IGMPv1, does not send IGMP leave message when leaving a multicast group, as a result, the switch can not get the leave information of the host momentarily. However, after leaving the multicast group, the host does not send IGMP report message any more, so the switch will remove the port from the corresponding multicast address table when its member port time times out. The host, running IGMPv2 or IGMPv3, sends IGMP leave message when leaving a multicast group to inform the multicast router of its leaving.

When receiving IGMP leave message, the switch will forward IGMP group-specific-query message to check if other members in the multicast group of the port need this multicast and reset the member port time to the leave time. When the leave time times out, the switch will remove the port from the corresponding multicast group. If no other member is in the group after the port is removed, the switch will send IGMP leave message to the router and remove the whole multicast group.

 IGMP Snooping Fundamentals

1. Ports

Router Port: Indicates the switch port directly connected to the multicast router.

Member Port: Indicates a switch port connected to a multicast group member.

2. Timers

Router Port Time: Within the time, if the switch does not receive IGMP query message from the router port, it will consider this port is not a router port any more. The default value is 300 seconds.

Member Port Time: Within the time, if the switch does not receive IGMP report message from the member port, it will consider this port is not a member port any more. The default value is 260 seconds.

Leave Time: Indicates the interval between the switch receiving a leave message from a host and the switch removing the host from the multicast groups. The default value is 1 second.

The IGMP Snooping function can be implemented on Snooping Config, Port Config, VLAN

Config and Multicast VLAN pages.

8.1.1 Snooping Config

To configure the IGMP Snooping on the switch, please firstly configure IGMP global configuration and related parameters on this page.

If the multicast address of the received multicast data is not in the multicast address table, the switch will broadcast the data in the VLAN. When Unknown Multicast Discard feature is enabled, the switch drops the received unknown multicast so as to save the bandwidth and enhance the process efficiency of the system. Please configure this feature appropriate to your needs.

Choose the menu Multicast→IGMP Snooping→Snooping Config to load the following page.

86

Figure 8-4 Basic Config

The following entries are displayed on this screen:

 Global Config

IGMP Snooping:

Unknown Multicast:

Select Enable/Disable IGMP Snooping function globally on the switch.

Select the operation for the switch to process unknown multicast,

Forward or Discard.

IGMP Snooping Status

Description:

Member:

Displays IGMP Snooping status.

Displays the member of the corresponding status.

8.1.2 Port Config

On this page you can configure the IGMP feature for ports of the switch.

Choose the menu Multicast→IGMP Snooping→Port Config to load the following page.

87

Figure 8-5 Port Config

The following entries are displayed on this screen:

Port Config

Port Select:

Select:

Port:

IGMP Snooping:

Fast Leave:

LAG:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for IGMP Snooping feature configuration.

It is multi-optional.

Displays the port of the switch.

Select Enable/Disable IGMP Snooping for the desired port.

Select Enable/Disable Fast Leave feature for the desired port. If

Fast Leave is enabled for a port, the switch will immediately remove this port from the multicast group upon receiving IGMP leave messages.

Displays the LAG number which the port belongs to.

Note:

1. Fast Leave on the port is effective only when the host supports IGMPv2 or IGMPv3.

2. When both Fast Leave feature and Unknown Multicast Discard feature are enabled, the leaving of a user connected to a port owning multi-user will result in the other users intermitting the multicast business.

8.1.3 VLAN Config

Multicast groups established by IGMP Snooping are based on VLANs. On this page you can configure different IGMP parameters for different VLANs.

Choose the menu Multicast→IGMP Snooping→VLAN Config to load the following page.

88

Figure 8-6 VLAN Config

The following entries are displayed on this screen:

VLAN Config

VLAN ID:

Router Port Time:

Member Port Time:

Leave Time:

Static Router Port:

Enter the VLAN ID to enable IGMP Snooping for the desired

VLAN.

Specify the aging time of the router port. Within this time, if the switch doesn’t receive IGMP query message from the router port, it will consider this port is not a router port any more.

Specify the aging time of the member port. Within this time, if the switch doesn’t receive IGMP report message from the member port, it will consider this port is not a member port any more.

Specify the interval between the switch receiving a leave message from a host and the switch removing the host from the multicast groups.

Enter the static router port which is mainly used in the network with stable topology.

 VLAN Table

VLAN ID Select:

Select:

VLAN ID:

Router Port Time:

Member Port Time:

Leave Time:

Click the Select button to quick-select the corresponding VLAN

ID based on the ID number you entered.

Select the desired VLAN ID for configuration. It is multi-optional.

Displays the VLAN ID.

Displays the router port time of the VLAN.

Displays the member port time of the VLAN.

Displays the leave time of the VLAN.

89

Router Port: Displays the router port of the VLAN.

Note:

The settings here will be invalid when multicast VLAN is enabled

Configuration procedure:

Step Operation Description function and for the port on Multicast→IGMP

Snooping→Snooping Config and Port Config page.

2 Configure the multicast parameters for VLANs on Multicast→IGMP Snooping→VLAN Config page.

If a VLAN has no multicast parameters configuration, it indicates the IGMP Snooping is not enabled in the VLAN, thus the multicast data in the VLAN will be broadcasted.

8.1.4 Multicast VLAN

In old multicast transmission mode, when users in different VLANs apply for join the same multicast group, the multicast router will duplicate this multicast information and deliver each

VLAN owning a receiver one copy. This mode wastes a lot of bandwidth.

The problem above can be solved by configuring a multicast VLAN. By adding switch ports to the multicast VLAN and enabling IGMP Snooping, you can make users in different VLANs share the same multicast VLAN. This saves the bandwidth since multicast streams are transmitted only within the multicast VLAN and also guarantees security because the multicast VLAN is isolated from user VLANS.

Before configuring a multicast VLAN, you should firstly configure a VLAN as multicast VLAN and add the corresponding ports to the VLAN on the 802.1Q VLAN page. If the multicast VLAN is enabled, the multicast configuration for other VLANs on the VLAN Config page will be invalid, that is, the multicast streams will be transmitted only within the multicast VLAN.

Choose the menu Multicast→IGMP Snooping→Multicast VLAN to load the following page.

Figure 8-7 Multicast VLAN

90

The following entries are displayed on this screen:

Multicast VLAN

Multicast VLAN:

VLAN ID:

Router Port Time:

Member Port Time:

Leave Time:

Select Enable/Disable Multicast VLAN feature.

Enter the VLAN ID of the multicast VLAN.

Specify the aging time of the router port. Within this time, if the switch doesn’t receive IGMP query message from the router port, it will consider this port is not a router port any more.

Specify the aging time of the member port. Within this time, if the switch doesn’t receive IGMP report message from the member port, it will consider this port is not a member port any more.

Specify the interval between the switch receiving a leave message from a host, and the switch removing the host from the multicast groups.

Note:

1. The router port should be in the multicast VLAN, otherwise the member ports can not receive multicast streams.

2. The Multicast VLAN won't take effect unless you first complete the configuration for the corresponding VLAN owning the port on the 802.1Q VLAN page.

3. Configure the link type of the router port in the multicast VLAN as Tagged otherwise all the member ports in the multicast VLAN can not receive multicast streams.

4. After a multicast VLAN is created, all the IGMP packets will be processed only within the multicast VLAN.

Configuration procedure:

Step Operation

2

Description function

Required. Enable IGMP Snooping globally on the switch and for the port on Multicast→IGMP

Snooping→Snooping Config and Port Config page.

Create a multicast VLAN Required. Create a multicast VLAN and add all the member ports and router ports to the VLAN on the VLAN→802.1Q

VLAN page.

Configure the link type of the router ports as Tagged.

4 multicast VLAN

Optional. Enable and configure a multicast VLAN on the

Multicast→IGMP Snooping→Multicast VLAN page.

It is recommended to keep the default time parameters.

Look over the configuration If it is successfully configured, the VLAN ID of the multicast

VLAN will be displayed in the IGMP Snooping Status table on the Multicast→IGMP Snooping→Snooping Config page.

91

Application Example for Multicast VLAN:

Network Requirements

Multicast source sends multicast streams via the router, and the streams are transmitted to user A and user B through the switch.

Router: Its WAN port is connected to the multicast source; its LAN port is connected to the switch.

The multicast packets are transmitted in VLAN3.

Switch: Port 3 is connected to the router and the packets are transmitted in VLAN3; port 4 is connected to user A and the packets are transmitted in VLAN4; port 5 is connected to user B and the packets are transmitted in VLAN5.

User A: Connected to Port 4 of the switch.

User B: Connected to port 5 of the switch.

Configure a multicast VLAN, and user A and B receive multicast streams through the multicast

VLAN.

92

 Network Diagram

Configuration Procedure

Step Operation Description

1 Create VLANs Create three VLANs with the VLAN ID 3, 4 and 5 respectively, and specify the description of VLAN3 as Multicast VLAN on

VLAN→802.1Q VLAN page.

2 Configure VLAN→802.1Q VLAN function pages.

For port 3, configure its link type as Tagged, and add it to VLAN3,

VLAN4 and VLAN5.

For port 4, configure its link type as Untagged, and add it to

VLAN3 and VLAN 4.

For port 5, configure its link type as Untagged, and add it to

VLAN3 and VLAN 5.

3 Enable IGMP

Snooping function Snooping→Snooping Config page. Enable IGMP Snooping function for port 3, port 4 and port 5 on Multicast→IGMP

Snooping→Port Config page.

5

VLAN VLAN as 3 and keep the other parameters as default on

Multicast→IGMP Snooping→Multicast VLAN page.

Check Multicast VLAN 3-5 and Multicast VLAN 3 will be displayed in the IGMP

Snooping Status table on the Multicast→IGMP

Snooping→Snooping Config page.

8.2 Multicast IP

In a network, receivers can join different multicast groups appropriate to their needs. The switch forwards multicast streams based on multicast address table. The Multicast IP can be implemented on Multicast IP Table, Static Multicast IP page.

93

8.2.1 Multicast IP Table

On this page you can view the multicast IP table on the switch.

Choose the menu Multicast→Multicast IP→Multicast IP Table to load the following page.

Figure 8-8 Multicast IP Table

The following entries are displayed on this screen:

 Search Option

Multicast IP:

VLAN ID:

Port:

Type:

Enter the multicast IP address the desired entry must carry.

Enter the VLAN ID the desired entry must carry.

Select the port number the desired entry must carry.

Select the type the desired entry must carry.

 All: Displays all multicast IP entries.

 Static: Displays all static multicast IP entries.

 Dynamic: Displays all dynamic multicast IP entries.

 Multicast IP Table

Multicast IP

VLAN ID:

Forward Port

Type:

Displays multicast IP address.

Displays the VLAN ID of the multicast group.

Displays the forward port of the multicast group.

Displays the type of the multicast IP.

Note:

If the configuration on VLAN Config page and multicast VLAN page is changed, the switch will clear up the dynamic multicast addresses in multicast address table and learn new addresses.

8.2.2 Static Multicast IP

Static Multicast IP table, isolated from dynamic multicast group and multicast filter, is not learned by IGMP Snooping. It can enhance the quality and security for information transmission in some fixed multicast groups.

Choose the menu Multicast→Multicast IP→Static Multicast IP to load the following page.

94

Figure 8-9 Static Multicast IP Table

The following entries are displayed on this screen:

Create Static Multicast

Multicast IP:

VLAN ID:

Forward Port:

Enter static multicast IP address.

Enter the VLAN ID of the multicast IP.

Enter the forward port of the multicast group.

Search Option

Search Option: Select the rules for displaying multicast IP table to find the desired entries quickly.

 All: Displays all static multicast IP entries.

 Multicast IP: Enter the multicast IP address the desired entry must carry.

 VLAN ID: Enter the VLAN ID the desired entry must carry.

 Port: Enter the port number the desired entry must carry.

Static Multicast IP Table

Select:

Multicast IP:

VLAN ID:

Forward Port:

Select the desired entry to delete the corresponding static multicast IP. It is multi-optional.

Displays the multicast IP.

Displays the VLAN ID of the multicast group.

Displays the forward port of the multicast group.

8.3 Multicast Filter

When IGMP Snooping is enabled, you can specified the multicast IP-range the ports can join so as to restrict users ordering multicast programs via configuring multicast filter rules.

When applying for a multicast group, the host will send IGMP report message. After receiving the report message, the switch will firstly check the multicast filter rules configured for the receiving

95

port. If the port can be added to the multicast group, it will be added to the multicast address table; if the port can not be added to the multicast group, the switch will drop the IGMP report message.

In that way, the multicast streams will not be transmitted to this port, which allows you to control hosts joining the multicast group.

8.3.1 IP-Range

On this page you can figure the desired IP-ranges to be filtered.

Choose the menu Multicast→Multicast Filter→IP-Range to load the following page.

Select:

IP-Range ID:

Start Multicast IP:

End Multicast IP:

Figure 8-10 Multicast Filter

The following entries are displayed on this screen:

 Create IP-Range

IP Range ID:

Start Multicast IP:

End Multicast IP:

Enter the IP-range ID.

Enter start multicast IP of the IP-range you set.

Enter end multicast IP of the IP-range you set.

 IP-Range Table

IP-Range ID Select: Click the Select button to quick-select the corresponding

IP-range ID based on the ID number you entered.

Select the desired entry to delete or modify the corresponding

IP-range. It is multi-optional.

Displays IP-range ID.

Displays start multicast IP of the IP-range.

Displays end multicast IP of the IP-range.

8.3.2 Port Filter

On this page you can configure the multicast filter rules for port. Take the configuration on this page and the configuration on IP-Range page together to function to implement multicast filter function on the switch.

Choose the menu Multicast→Multicast Filter→Port Filter to load the following page.

96

Figure 8-11 Port Filter

The following entries are displayed on this screen:

Port Filter Config

Port Select:

Select:

Port:

Filter:

Action Mode:

Bound IP-Range (ID):

Max Groups:

LAG:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for multicast filtering. It is multi-optional.

Displays the port number.

Select Enable/Disable multicast filtering feature on the port.

Select the action mode to process multicast packets when the multicast IP is in the filtering IP-range.

 Permit: Only the multicast packets whose multicast IP is in the IP-range will be processed.

 Deny: Only the multicast packets whose multicast IP is not in the IP-range will be processed.

Enter the IP-rang ID the port will be bound to.

Specify the maximum number of multicast groups to prevent some ports taking up too much bandwidth.

Displays the LAG number which the port belongs to.

Note:

1. Multicast Filter feature can only have effect on the VLAN with IGMP Snooping enabled.

2. Multicast Filter feature has no effect on static multicast IP.

3. Up to 15 IP-Ranges can be bound to one port.

Configuration Procedure:

97

Step Operation Description

1 Configure Configure IP-Range to be filtered on

Multicast→Multicast Filter→IP-Range page.

2 Configure multicast filter rules for ports

Optional. Configure multicast filter rules for ports on

Multicast→Multicast Filter→Port Filter page.

8.4 Packet Statistics

On this page you can view the multicast data traffic on each port of the switch, which facilitates you to monitor the IGMP messages in the network.

Choose the menu Multicast→Packet Statistics to load the following page.

Figure 8-12 Packet Statistics

The following entries are displayed on this screen:

Auto Refresh

Auto Refresh:

Refresh Period:

Select Enable/Disable auto refresh feature.

Enter the time from 3 to 300 in seconds to specify the auto refresh period.

 IGMP Statistics

Port Select:

Port:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Displays the port number of the switch.

98

Query Packet:

Report Packet (V1):

Report Packet (V2):

Report Packet (V3):

Leave Packet:

Error Packet:

Displays the number of query packets the port received.

Displays the number of IGMPv1 report packets the port received.

Displays the number of IGMPv2 report packets the port received.

Displays the number of IGMPv3 report packets the port received.

Displays the number of leave packets the port received.

Displays the number of error packets the port received.

Return to CONTENTS

99

Chapter 9 QoS

QoS (Quality of Service) functions to provide different quality of service for various network applications and requirements and optimize the bandwidth resource distribution so as to provide a network service experience of a better quality.

QoS

This switch classifies the ingress packets, maps the packets to different priority queues and then forwards the packets according to specified scheduling algorithms to implement QoS function.

Figure 9-1 QoS function

 Traffic classification: Identifies packets conforming to certain characters according to certain rules.

 Map: The user can map the ingress packets to different priority queues based on the priority modes. This switch implements three priority modes based on port, on 802.1P and on DSCP.

 Queue scheduling algorithm: When the network is congested, the problem that many packets compete for resources must be solved, usually in the way of queue scheduling. The switch supports four schedule modes: SP, WRR, SP+WRR and Equ.

Priority Mode

This switch implements three priority modes based on port, on 802.1P and on DSCP. By default, the priority mode based on port is enabled and the other two modes are optional.

Port priority is just a property of the port. After port priority is configured, the data stream will be mapped to the egress queues according to the CoS of the port and the mapping relationship between CoS and queues.

100

Figure 9-2 802.1Q frame

As shown in the figure above, each 802.1Q Tag has a Pri field, comprising 3 bits. The 3-bit priority field is 802.1p priority in the range of 0 to 7. 802.1P priority determines the priority of the packets based on the Pri value. On the Web management page of the switch, you can configure different priority tags mapping to the corresponding priority levels, and then the switch determine which packet is sent preferentially when forwarding packets. The switch processes untagged packets based on the default priority mode.

Figure 9-3 IP datagram

As shown in the figure above, the ToS (Type of Service) in an IP header contains 8 bits. The first three bits indicate IP precedence in the range of 0 to 7. RFC2474 re-defines the ToS field in the IP packet header, which is called the DS field. The first six bits (bit 0-bit 5) of the DS field indicate

DSCP precedence in the range of 0 to 63. The last 2 bits (bit 6 and bit 7) are reserved. On the Web management page, you can configure different DS field mapping to the corresponding priority levels. Non-IP datagram with 802.1Q tag are mapped to different priority levels based on 802.1P priority mode; the untagged non-IP datagram are mapped based on port priority mode.

Schedule Mode

When the network is congested, the problem that many packets compete for resources must be solved, usually in the way of queue scheduling. The switch implements four scheduling queues,

TC0, TC1, TC2 and TC3. TC0 has the lowest priority while TC3 has the highest priority. The switch provides four schedule modes: SP, WRR, SP+WRR and Equ. whole bandwidth. Packets in the queue with lower priority are sent only when the queue with higher priority is empty. The switch has four egress queues labeled as TC0, TC1, TC2 and

TC3. In SP mode, their priorities increase in order. TC3 has the highest priority. The disadvantage of SP queue is that: if there are packets in the queues with higher priority for a long time in congestion, the packets in the queues with lower priority will be “starved to death” because they are not served.

101

Figure 9-4 SP-Mode

2. WRR-Mode: Weight Round Robin Mode. In this mode, packets in all the queues are sent in order based on the weight value for each queue and every queue can be assured of a certain service time. The weight value indicates the occupied proportion of the resource. WRR queue overcomes the disadvantage of SP queue that the packets in the queues with lower priority can not get service for a long time. In WRR mode, though the queues are scheduled in order, the service time for each queue is not fixed, that is to say, if a queue is empty, the next queue will be scheduled. In this way, the bandwidth resources are made full use of. The default weight value ratio of TC0, TC1, TC2 and TC3 is 1:2:4:8.

Figure 9-5 WRR-Mode

3. SP+WRR-Mode: Strict-Priority + Weight Round Robin Mode. In this mode, this switch provides two scheduling groups, SP group and WRR group. Queues in SP group and WRR group are scheduled strictly based on strict-priority mode while the queues inside WRR group follow the WRR mode. In SP+WRR mode, TC3 is in the SP group; TC0, TC1 and TC2 belong to the WRR group and the weight value ratio of TC0, TC1 and TC2 is 1:2:4. In this way, when scheduling queues, the switch allows TC3 to occupy the whole bandwidth following the SP mode and the TC0, TC1 and TC2 in the WRR group will take up the bandwidth according to their ratio 1:2:4.

102

4. Equ-Mode: Equal-Mode. In this mode, all the queues occupy the bandwidth equally. The weight value ratio of all the queues is 1:1:1:1.

The QoS module is mainly for traffic control and priority configuration, including three submenus:

DiffServ, Bandwidth Control and Voice VLAN.

9.1 DiffServ

This switch classifies the ingress packets, maps the packets to different priority queues and then forwards the packets according to specified scheduling algorithms to implement QoS function.

This switch implements three priority modes based on port, on 802.1P and on DSCP, and supports four queue scheduling algorithms. The port priorities are labeled as CoS0, CoS1… CoS7.

The DiffServ function can be implemented on Port Priority, 802.1P/Cos mapping, DSCP Priority and Schedule Mode pages.

9.1.1 Port Priority

On this page you can configure the port priority.

Choose the menu QoS→DiffServ→Port Priority to load the following page.

For TL-SG2210P:

Figure 9-6 Port Priority Config for TL-SG2210P

The following entries are displayed on this screen:

 Port Priority Config

Select:

Port:

Priority:

LAG:

Select the desired port to configure its priority. It is multi-optional.

Displays the physical port number of the switch.

Specify the priority for the port.

Displays the LAG number which the port belongs to.

103

Configuration Procedure:

Step Operation

1 Select the port priority

2 Select a schedule mode

Description

Required. On QoS→DiffServ→Port Priority page, configure the port priority.

Required. On QoS→DiffServ→Schedule Mode page, select a schedule mode.

For TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452:

Figure 9-7 Port Priority Config

The following entries are displayed on this screen:

 Port Priority Config

Select:

Port:

Priority:

LAG:

Select the desired port to configure its priority. It is multi-optional.

Displays the physical port number of the switch.

Specify the priority for the port.

Displays the LAG number which the port belongs to.

Configuration Procedure:

Step Operation

1 Select the port priority

Description

Required. On QoS→DiffServ→Port Priority page, configure the port priority.

3 relation between the 802.1P priority and TC configure the mapping relation between the 802.1P priority and TC.

Select a schedule mode Required. On QoS→DiffServ→Schedule Mode page, select a schedule mode.

104

9.1.2 802.1P/CoS mapping

On this page you can configure the mapping relation between the 802.1P priority tag-id/CoS-id and the TC-id.

802.1P gives the Pri field in 802.1Q tag a recommended definition. This field, ranging from 0-7, is used to divide packets into 8 priorities. 802.1P Priority is enabled by default, so the packets with

802.1Q tag are mapped to different priority levels based on 802.1P priority mode but the untagged packets are mapped based on port priority mode. With the same value, the 802.1P priority tag and the CoS will be mapped to the same TC.

Choose the menu QoS→DiffServ→802.1P/CoS mapping to load the following page.

Figure 9-8 802.1P/CoS mapping

The following entries are displayed on this screen :

 802.1P Priority Config

802.1P Priority: Select Enable or Disable 802.1P Priority.

 Priority and CoS-mapping Config

Tag-id/Cos-id:

Queue TC-id:

Indicates the precedence level defined by IEEE802.1P and the

CoS ID.

Indicates the priority level of egress queue the packets with tag and CoS-id are mapped to. The priority levels of egress queue are labeled as TC0, TC1, TC2 and TC3.

Note:

For TL-SG2216/TL-SG2424/TL-SG2424P, the 802.1P priority function is enabled by default and cannot be set as disabled.

Configuration Procedure:

Step Operation Description relation between the 802.1P priority Tag/CoS and the TC page, configure the mapping relation between the

802.1P priority Tag/CoS and the TC.

105

Step Operation

2 Select a schedule mode

Description

Required. On QoS→DiffServ→Schedule Mode page,, select a schedule mode.

9.1.3 DSCP Priority

On this page you can configure DSCP priority. DSCP (DiffServ Code Point) is a new definition to IP

ToS field given by IEEE. This field is used to divide IP datagram into 64 priorities. When DSCP

Priority is enabled, IP datagram are mapped to different priority levels based on DSCP priority mode; non-IP datagram with 802.1Q tag are mapped to different priority levels based on 802.1P priority mode if 8021.1P Priority mode is enabled; the untagged non-IP datagram are mapped based on port priority mode.

Choose the menu QoS→DiffServ→DSCP Priority to load the following page.

For TL-SG2210P/TL-SG2452:

Figure 9-9 DSCP Priority for TL-SG2210P/TL-SG2452

The following entries are displayed on this screen :

DSCP Priority Config

Select Enable or Disable DSCP Priority.

DSCP Priority:

Priority Level

DSCP:

Priority Level:

Indicates the priority determined by the DS region of IP datagram.

It ranges from 0 to 63.

Indicates the 802.1P priority the packets with tag are mapped to.

The priorities are labeled as TC0 ~ TC3.

106

Configuration Procedure:

Step Operation Description

2 relation between the DSCP priority and 802.1P priority enable DSCP Priority and configure the mapping relation between the DSCP priority and TC.

Select a schedule mode Required. On QoS→DiffServ→Schedule Mode page, select a schedule mode.

For TL-SG2216/TL-SG2424/TL-SG2424P:

Figure 9-10 DSCP Priority

The following entries are displayed on this screen :

 DSCP Priority Config

DSCP Priority:

Priority Level

Select Enable or Disable DSCP Priority.

DSCP:

Priority Level:

Indicates the priority determined by the DS region of IP datagram.

It ranges from 0 to 63.

Indicates the 802.1P priority the packets with tag are mapped to.

The priorities are labeled as CoS0 ~ CoS7.

107

Configuration Procedure:

Step Operation Description relation between the DSCP priority and 802.1P priority enable DSCP Priority and configure the mapping relation between the DSCP priority and CoS.

3 relation between the CoS and the TC page, configure the mapping relation between the CoS and the TC.

Select a schedule mode Required. On QoS→DiffServ→Schedule Mode page, select a schedule mode.

9.1.4 Schedule Mode

On this page you can select a schedule mode for the switch. When the network is congested, the problem that many packets compete for resources must be solved, usually in the way of queue scheduling. The switch will control the forwarding sequence of the packets according to the priority queues and scheduling algorithms you set. On this switch, the priority levels are labeled as TC0,

TC1… TC3.

Choose the menu QoS→DiffServ→Schedule Mode to load the following page.

Figure 9-11 Schedule Mode

The following entries are displayed on this screen :

 Schedule Mode Config

SP-Mode:

WRR-Mode:

SP+WRR-Mode:

Equ-Mode:

Strict-Priority Mode. In this mode, the queue with higher priority will occupy the whole bandwidth. Packets in the queue with lower priority are sent only when the queue with higher priority is empty.

Weight Round Robin Mode. In this mode, packets in all the queues are sent in order based on the weight value for each queue. The weight value ratio of TC0, TC1, TC2 and TC3 is 1:2:4:8.

Strict-Priority + Weight Round Robin Mode. In this mode, this switch provides two scheduling groups, SP group and WRR group. Queues in SP group and WRR group are scheduled strictly based on strict-priority mode while the queues inside WRR group follow the

WRR mode. In SP+WRR mode, TC3 is in the SP group; TC0, TC1 and TC2 belong to the WRR group and the weight value ratio of

TC0, TC1 and TC2 is 1:2:4. In this way, when scheduling queues, the switch allows TC3 to occupy the whole bandwidth following the

SP mode and the TC0, TC1 and TC2 in the WRR group will take up the bandwidth according to their ratio 1:2:4.

Equal-Mode. In this mode, all the queues occupy the bandwidth equally. The weight value ratio of all the queues is 1:1:1:1.

108

9.2 Bandwidth Control

Bandwidth function, allowing you to control the traffic rate and broadcast flow on each port to ensure network in working order, can be implemented on Rate Limit and Storm Control pages.

9.2.1 Rate Limit

Rate limit functions to control the ingress/egress traffic rate on each port via configuring the available bandwidth of each port. In this way, the network bandwidth can be reasonably distributed and utilized.

Choose the menu QoS→Bandwidth Control→Rate Limit to load the following page.

Figure 9-12 Rate Limit

The following entries are displayed on this screen:

Rate Limit Config

Port Select:

Select:

Port:

Ingress Rate (bps):

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for Rate configuration. It is multi-optional.

Displays the port number of the switch.

Configure the bandwidth for receiving packets on the port. You can select a rate from the dropdown list or select "Manual" to set Ingress rate, the system will automatically select integral multiple of 64Kbps that closest to the rate you entered as the real Ingress rate.

109

Egress Rate(bps): Configure the bandwidth for sending packets on the port. You can select a rate from the dropdown list or select "Manual" to set Egress rate, the system will automatically select integral multiple of 64Kbps that closest to the rate you entered as the real Egress rate.

Displays the LAG number which the port belongs to. LAG:

Note:

1. If you enable ingress rate limit feature for the storm control-enabled port, storm control feature will be disabled for this port.

2. When selecting "Manual" to set Ingress/Egress rate, the system will automatically select integral multiple of 64Kbps that closest to the rate you entered as the real Ingress/Egress rate.

For example, if you enter 1000Kbps for egress rate, the system will automatically select

1024Kbps as the real Egress rate.

3. When egress rate limit feature is enabled for one or more ports, you are suggested to disable the flow control on each port to ensure the switch works normally.

9.2.2 Storm Control

Storm Control function allows the switch to filter broadcast, multicast and UL frame in the network.

If the transmission rate of the three kind packets exceeds the set bandwidth, the packets will be automatically discarded to avoid network broadcast storm.

Choose the menu QoS→Bandwidth Control→Storm Control to load the following page.

For TL-SG2210P/TL-SG2216/TL-SG2424/TL-SG2424P:

Figure 9-13 Storm Control

110

The following entries are displayed on this screen:

Storm Control Config

Port Select:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select:

Select the desired port for Storm Control configuration. It is multi-optional.

Port:

Broadcast Rate

(bps):

Mulitcast Rate

(bps):

UL-Frame Rate

(bps):

LAG:

Displays the port number of the switch.

Select the bandwidth for receiving broadcast packets on the port.

The packet traffic exceeding the bandwidth will be discarded.

Select Disable to disable the storm control function for the port.

Select the bandwidth for receiving multicast packets on the port.

The packet traffic exceeding the bandwidth will be discarded.

Select Disable to disable the storm control function for the port.

Select the bandwidth for receiving UL-Frame on the port. The packet traffic exceeding the bandwidth will be discarded. Select

Disable to disable the storm control function for the port.

Displays the LAG number which the port belongs to.

Note:

If you enable storm control feature for the ingress rate limit-enabled port, ingress rate limit feature will be disabled for this port.

For TL-SG2452:

Figure 9-14 Storm Control

111

The following entries are displayed on this screen:

Storm Control Config

Port Select:

Select:

Port:

Broadcast:

Multicast:

UL-Frame:

Rate (bps):

LAG:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for Storm Control configuration. It is multi-optional.

Displays the port number of the switch.

Enable/Disable broadcast control feature for the port.

Enable/Disable multicast control feature for the port.

Enable/Disable UL-Frame control feature for the port.

Select the bandwidth for receiving the specified packet on the port.

The packet traffic exceeding the bandwidth will be discarded.

Displays the LAG number which the port belongs to.

Note:

If you enable storm control feature for the ingress rate limit-enabled port, ingress rate limit feature will be disabled for this port.

9.3 Voice VLAN

Voice VLANs are configured specially for voice data stream. By configuring Voice VLANs and adding the ports with voice devices attached to voice VLANs, you can perform QoS-related configuration for voice data, ensuring the transmission priority of voice data stream and voice quality.

 OUI Address (Organizationally unique identifier address)

The switch can determine whether a received packet is a voice packet by checking its source MAC address. If the source MAC address of a packet complies with the OUI addresses configured by the system, the packet is determined as voice packet and transmitted in voice VLAN.

An OUI address is a unique identifier assigned by IEEE (Institute of Electrical and Electronics

Engineers) to a device vendor. It comprises the first 24 bits of a MAC address. You can recognize which vendor a device belongs to according to the OUI address. The following table shows the

OUI addresses of several manufacturers. The following OUI addresses are preset of the switch by default.

Number OUI Address Vendor

112

Number OUI Address Vendor

Table 9-1 OUI addresses on the switch

Port Voice VLAN Mode

A voice VLAN can operate in two modes: automatic mode and manual mode.

Automatic Mode: In this mode, the switch automatically adds a port which receives voice packets to voice VLAN and determines the priority of the packets through learning the source MAC of the

UNTAG packets sent from IP phone when it is powered on. The aging time of voice VLAN can be configured on the switch. If the switch does not receive any voice packet on the ingress port within the aging time, the switch will remove this port from voice VLAN. Voice ports are automatically added into or removed from voice VLAN.

Manual Mode: You need to manually add the port of IP phone to voice VLAN, and then the switch will assign ACL rules and configure the priority of the packets through learning the source MAC address of packets and matching OUI address.

In practice, the port voice VLAN mode is configured according to the type of packets sent out from voice device and the link type of the port. The following table shows the detailed information.

Port Voice

VLAN Mode

Voice

Stream Type

Link type of the port and processing mode

Automatic Mode

TAG voice stream

Untagged: Not supported.

Tagged: Supported. The default VLAN of the port can not be voice VLAN.

UNTAG voice stream

Untagged: Supported.

Tagged: Not supported.

Manual Mode

Untagged: Not supported.

TAG voice stream

Tagged:Supported. The default VLAN of the port should not be voice VLAN.

UNTAG voice stream

Untagged: Supported.

Tagged: Not supported.

Table 9-2 Port voice VLAN mode and voice stream processing mode

Security Mode of Voice VLAN

When voice VLAN is enabled for a port, you can configure its security mode to filter data stream. If security mode is enabled, the port just forwards voice packets, and discards other packets whose source MAC addresses do not match OUI addresses. If security mode is not enabled, the port forwards all the packets.

113

Security Mode Packet Type

Enable

Processing Mode

UNTAG packet

Packet with voice

VLAN TAG

When the source MAC address of the packet is the OUI address that can be identified, the packet can be transmitted in the voice VLAN. Otherwise, the packet will be discarded.

Disable

Packet with other

VLAN TAG

The processing mode for the device to deal with the packet is determined by whether the port permits the VLAN or not, independent of voice VLAN security mode.

UNTAG packet

Packet with voice

VLAN TAG

Do not check the source MAC address of the packet and all the packets can be transmitted in the voice VLAN.

Packet with other

VLAN TAG

The processing mode for the device to deal with the packet is determined by whether the port permits the VLAN or not, independent of voice VLAN security mode.

Table 9-3 Security mode and packets processing mode

Note:

Don’t transmit voice stream together with other business packets in the voice VLAN except for some special requirements.

The Voice VLAN function can be implemented on Global Config, Port Config and OUI Config pages.

9.3.1 Global Config

On this page, you can configure the global parameters of the voice VLAN, including VLAN ID and aging time.

Choose the menu QoS→Voice VLAN→Global Config to load the following page.

Figure 9-15 Global Configuration

The following entries are displayed on this screen:

Global Config

Voice VLAN:

VLAN ID:

Aging Time:

Priority:

Select Enable/Disable Voice VLAN function.

Enter the VLAN ID of the voice VLAN.

Specifies the living time of the member port in auto mode after the

OUI address is aging out.

Select the priority of the port when sending voice data.

114

9.3.2 Port Config

Before the voice VLAN function is enabled, the parameters of the ports in the voice VLAN should be configured on this page.

Choose the menu QoS→Voice VLAN→Port Config to load the following page.

Figure 9-16 Port Config

Note:

To enable voice VLAN function for the LAG member port, please ensure its member state accords with its port mode.

If a port is a member port of voice VLAN, changing its port mode to be “Auto” will make the port leave the voice VLAN and will not join the voice VLAN automatically until it receives voice streams.

The following entries are displayed on this screen:

Port Config

Port Select:

Select:

Port:

Port Mode:

Security Mode:

Member State:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Select the desired port for voice VLAN configuration. It is multi-optional.

Displays the port number of the switch.

Select the mode for the port to join the voice VLAN.

Auto: In this mode, the switch automatically adds a port to the voice VLAN or removes a port from the voice VLAN by checking whether the port receives voice data or not.

Manual: In this mode, you can manually add a port to the voice VLAN or remove a port from the voice VLAN.

Configure the security mode for forwarding packets.

Disable: All packets are forwarded.

Enable: Only voice data are forwarded.

Displays the state of the port in the current voice VLAN.

115

LAG: Displays the LAG number which the port belongs to.

9.3.3 OUI Config

The switch supports OUI creation and adds the MAC address of the special voice device to the

OUI table of the switch. The switch determines whether a received packet is a voice packet by checking its OUI address. The switch analyzes the received packets. If the packets recognized as voice packets, the access port will be automatically added to the Voice VLAN.

Choose the menu QoS→Voice VLAN→OUI Config to load the following page.

Figure 9-17 OUI Configuration

The following entries are displayed on this screen:

Create OUI

OUI:

Mask:

Description:

Enter the OUI address of the voice device.

Enter the OUI address mask of the voice device.

Give a description to the OUI for identification.

 OUI Table

Select:

OUI:

Mask:

Description:

Select the desired entry to view the detailed information.

Displays the OUI address of the voice device.

Displays the OUI address mask of the voice device.

Displays the description of the OUI.

Configuration Procedure of Voice VLAN:

Step Operation

1 Configure the link type of the port

Description

Required. On VLAN→802.1Q VLAN→VLAN Config page, configure the link type of ports of the voice device.

116

4

5

Step Operation

3

Description

Add OUI address

Configure the parameters of the ports in voice VLAN.

Enable Voice VLAN page, click the Create button to create a VLAN.

Optional. On QoS→Voice VLAN→OUI Config page, you can check whether the switch is supporting the OUI template or not. If not, please add the OUI address.

Required. On QoS→Voice VLAN→Port Config page, configure the parameters of the ports in voice VLAN.

Required. On QoS→Voice VLAN→Global Config page, configure the global parameters of voice VLAN.

Return to CONTENTS

117

Chapter 10 ACL

10.1 ACL Config

An ACL may contain a number of rules, and each rule specifies a different package range. Packets are matched in match order. Once a rule is matched, the switch processes the matched packets taking the operation specified in the rule without considering the other rules, which can enhance the performance of the switch.

The ACL Config function can be implemented on ACL Summary, ACL Create, MAC ACL,

Standard-IP ACL and Extend-IP ACL pages.

10.1.1 ACL Summary

On this page, you can view the current ACLs configured in the switch.

Choose the menu ACL→ACL Config→ACL Summary to load the following page.

Figure 10-1 ACL Summary

The following entries are displayed on this screen:

 Search Option

Select ACL:

ACL Type:

Rule Order:

Select the ACL you have created

Displays the type of the ACL you select.

Displays the rule order of the ACL you select.

 Rule Table

Display the rule table of the ACL you have selected. Here you can edit the rules, view the details of them, and move them up and down.

10.1.2 ACL Create

On this page you can create ACLs.

Choose the menu ACL→ACL Config→ACL Create to load the following page.

118

Figure 10-2 ACL Create

The following entries are displayed on this screen:

Create ACL

ACL ID:

Rule Order:

Enter ACL ID of the ACL you want to create.

User Config order is set to be match order in this ACL.

10.1.3 MAC ACL

MAC ACLs analyze and process packets based on a series of match conditions, which can be the source MAC addresses and destination MAC addresses carried in the packets.

Choose the menu ACL→ACL Config→MAC ACL to load the following page.

Figure 10-3 Create MAC Rule

The following entries are displayed on this screen:

 Create MAC ACL

ACL ID:

Rule ID:

Operation:

S-MAC:

Select the desired MAC ACL for configuration.

Enter the rule ID.

Select the operation for the switch to process packets which match the rules.

Permit: Forward packets.

Deny: Discard Packets.

Enter the source MAC address contained in the rule.

119

D-MAC:

MASK:

Enter the destination MAC address contained in the rule.

Enter MAC address mask. If it is set to 1, it must strictly match the address.

10.1.4 Standard-IP ACL

Standard-IP ACLs analyze and process data packets based on a series of match conditions, which can be the source IP addresses and destination IP addresses carried in the packets.

Choose the menu ACL→ACL Config→Standard-IP ACL to load the following page.

Figure 10-4 Create Standard-IP Rule

The following entries are displayed on this screen:

 Create Standard-IP ACL

ACL ID:

Rule ID:

Operation:

S-IP:

D-IP:

Mask:

Select the desired Standard-IP ACL for configuration.

Enter the rule ID.

Select the operation for the switch to process packets which match the rules.

Permit: Forward packets.

Deny: Discard Packets.

Enter the source IP address contained in the rule.

Enter the destination IP address contained in the rule.

Enter IP address mask. If it is set to 1, it must strictly match the address.

10.1.5 Extend-IP ACL

Extend-IP ACLs analyze and process data packets based on a series of match conditions, which can be the source IP addresses, destination IP addresses, IP protocol and other information of this sort carried in the packets.

Choose the menu ACL→ACL Config→Extend-IP ACL to load the following page.

120

Figure 10-5 Create Extend-IP Rule

The following entries are displayed on this screen:

 Create Extend-IP ACL

ACL ID:

Rule ID:

Operation:

S-IP:

D-IP:

Mask:

IP Protocol:

S-Port:

D-Port:

Select the desired Extend-IP ACL for configuration.

Enter the rule ID.

Select the operation for the switch to process packets which match the rules.

Permit: Forward packets.

Deny: Discard Packets.

Enter the source IP address contained in the rule.

Enter the destination IP address contained in the rule.

Enter IP address mask. If it is set to 1, it must strictly match the address.

Select IP protocol contained in the rule.

Configure TCP/IP source port contained in the rule when TCP/UDP is selected from the pull-down list of IP Protocol.

Configure TCP/IP destination port contained in the rule when

TCP/UDP is selected from the pull-down list of IP Protocol.

10.2 Policy Config

A Policy is used to control the data packets those match the corresponding ACL rules by configuring ACLs and actions together for effect.

The Policy Config can be implemented on Policy Summary, Police Create and Action Create pages.

121

10.2.1 Policy Summary

On this page, you can view the ACL and the corresponding operations in the policy.

Choose the menu ACL→Policy Config→Policy Summary to load the following page.

Figure 10-6 Policy Summary

The following entries are displayed on this screen:

 Search Option

Select Policy: Select name of the desired policy for view. If you want to delete the desired policy, please click the Delete button.

Action Table

Select:

Index:

ACL ID:

Select the desired entry to delete the corresponding policy.

Displays the index of the policy.

Displays the ID of the ACL contained in the policy.

10.2.2 Policy Create

On this page you can create the policy.

Choose the menu ACL→Policy Config→Policy Create to load the following page.

Figure 10-7 Create Policy

The following entries are displayed on this screen:

Create Policy

Policy Name: Enter the name of the policy.

122

10.2.3 Action Create

On this page you can add ACLs for the policy.

Choose the menu ACL→Policy Config→Action Create to load the following page.

Figure 10-8 Action Create

The following entries are displayed on this screen:

 Create Action

Select Policy:

Select ACL:

Select the name of the policy.

Select the ACL for configuration in the policy.

10.3 Policy Binding

Policy Binding function can have the policy take its effect on a specific port/VLAN. The policy will take effect only when it is bound to a port/VLAN. In the same way, the port/VLAN will receive the data packets and process them based on the policy only when the policy is bound to the port/VLAN.

The Policy Binding can be implemented on Binding Table, Port Binding and VLAN Binding pages.

10.3.1 Binding Table

On this page view the policy bound to port/VLAN.

Choose the menu ACL→Policy Binding→Binding Table to load the following page.

Figure 10-9 Binding Table

The following entries are displayed on this screen:

 Search Option

Show Mode: Select a show mode appropriate to your needs.

123

 Policy Bind Table

Select:

Index:

Policy Name:

Interface:

Direction:

Select the desired entry to delete the corresponding binding policy.

Displays the index of the binding policy.

Displays the name of the binding policy.

Displays the port number or VLAN ID bound to the policy.

Displays the binding direction.

10.3.2 Port Binding

On this page you can bind a policy to a port.

Choose the menu ACL→Policy Binding→Port Binding to load the following page.

Figure 10-10 Bind the policy to the port

The following entries are displayed on this screen:

 Port-Bind Config

Policy Name:

Port:

Select the name of the policy you want to bind.

Enter the number of the port you want to bind.

 Port-Bind Table

Index:

Policy Name:

Port:

Direction:

Displays the index of the binding policy.

Displays the name of the binding policy.

Displays the number of the port bound to the corresponding policy.

Displays the binding direction.

Note:

For TL-SG2216/TL-SG2424/TL-SG2424P, you can bind one policy to multiple interfaces; but for

TL-SG2452, you can bind one policy to only one interface

10.3.3 VLAN Binding

On this page you can bind a policy to a VLAN.

Choose the menu ACL→Policy Binding→VLAN Binding to load the following page.

124

Figure 10-11 Bind the policy to the VLAN

The following entries are displayed on this screen:

VLAN-Bind Config

Policy Name:

VLAN ID:

Select the name of the policy you want to bind.

Enter the ID of the VLAN you want to bind.

 VLAN-Bind Table

Index:

Policy Name:

VLAN ID:

Direction:

Displays the index of the binding policy.

Displays the name of the binding policy.

Displays the ID of the VLAN bound to the corresponding policy.

Displays the binding direction.

Configuration Procedure:

Step Operation Description configure ACL rules to match packets. configure the policy to control the data packets those match the corresponding ACL rules.

3 Bind the policy to the Required. On ACL→Policy Binding configuration pages, port/VLAN bind the policy to the port/VLAN to make the policy effective on the corresponding port/VLAN.

Note:

For TL-SG2216/TL-SG2424/TL-SG2424P, you can bind one policy to multiple VLANs; but for

TL-SG2452, you can bind one policy to only one VLAN

10.4 Application Example for ACL

Network Requirements

1. The manager of the R&D department can access to the forum of the company and the Internet without any forbiddance. The MAC address of the manager is 00-64-A5-5D-12-C3.

2. The staff of the R&D department can not access to the Internet but can visit the forum.

125

3. The staff of the marketing department can access to the Internet but can not visit the forum.

4. The R&D department and marketing department can not communicate with each other.

Network Diagram

Configuration Procedure

Step Operation Description

1 Configure requirement 1

On ACL→ACL Config→ACL Create page, create ACL 11.

On ACL→ACL Config→MAC ACL page, select ACL 11, create Rule 1, configure the operation as Permit, configure the S-MAC as

00-64-A5-5D-12-C3 and mask as FF-FF-FF-FF-FF-FF.

On ACL→Policy Config→Policy Create page, create a policy named manager.

On ACL→Policy Config→Action Create page, add ACL 11 to Policy manager.

On ACL→Policy Binding→Port Binding page, select Policy manager to bind to port 3.

126

Step Operation Description and 4

On ACL→ACL Config→ACL Create page, create ACL 100. requirement 2 create Rule 1, configure operation as Deny, configure S-IP as

10.10.70.0 and mask as 255.255.255.0, configure D-IP as 10.10.50.0 and mask as 255.255.255.0.

On ACL→ACL Config→Standard-IP ACL page, select ACL 100, create Rule 2, configure operation as Deny, configure S-IP as

10.10.70.0 and mask as 255.255.255.0, configure D-IP as 10.10.88.5 and mask as 255.255.255.255.

On ACL→ACL Config→Standard-IP ACL page, select ACL 100, create Rule 3, configure operation as Permit, configure S-IP as

10.10.70.0 and mask as 255.255.255.0, configure D-IP as 10.10.88.5 and mask as 255.255.255.255.

On ACL→Policy Config→Policy Create page, create a policy named limit1.

On ACL→Policy Config→Action Create page, add ACL 100 to Policy limit1.

On ACL→Policy Binding→Port Binding page, select Policy limit1 to bind to port 3. for requirement 3 and 4

On ACL→ACL Config→Standard-IP ACL page, select ACL 101, create Rule 4, configure operation as Deny, configure S-IP as

10.10.70.0 and mask as 255.255.255.0, configure D-IP as 10.10.50.0 and mask as 255.255.255.0.

On ACL→ACL Config→Standard-IP ACL page, select ACL 101, create Rule 5, configure operation as Deny, configure S-IP as

10.10.70.0 and mask as 255.255.255.0, configure D-IP as 10.10.88.5 and mask as 255.255.255.255.

On ACL→Policy Config→Policy Create page, create a policy named limit2.

On ACL→Policy Config→Action Create page, add ACL 101 to Policy limit2.

On ACL→Policy Binding→Port Binding page, select Policy limit2 to bind to port 4.

Return to CONTENTS

127

Chapter 11 PoE

Note:

Only TL-SG2210P and TL-SG2424P support PoE function.

PoE (Power over Ethernet) technology describes a system to transmit electrical power along with data to remote devices over standard twisted-pair cable in an Ethernet network. It is especially useful for supplying power to IP telephones, wireless LAN access points, cameras and so on.

Composition

A PoE system usually consists of PSE and PD.

PSE: Power sourcing equipment (PSE) is a device such as a switch that provides power on the

Ethernet cable to the linked device.

PD: A powered device (PD) is a device accepting power from the PSE and thus consumes energy.

PDs falls into two types, standard PDs and nonstandard PDs. Standard PDs refer to the powered devices that comply with IEEE 802.3af (for TL-SG2210P/TL-SG2424P) and IEEE 802.3at (for

TL-SG2424P). Examples include wireless LAN access points, IP Phones, IP cameras, network hubs, embedded computers etc.

Advantage

 Cheap cabling: The remote device such as cameras can be powered by PSE in no need of prolonging its power cord additionally and Ethernet cable is much cheaper than AC wire or power cord.

 Easy to connect: PoE uses only one Ethernet cable with no need of external power supply.

 Reliable: A powered device can be either powered by PSE using Ethernet cable or powered through the provided power adapter. It is very convenient to provide a backup power supply for the PDs.

 Flexibility: In compliance with IEEE 802.3af (for TL-SG2210P/TL-SG2424P) and IEEE

802.3at (for TL-SG2424P), global organizations can deploy PoE everywhere without concern for any local variance in AC power standards, outlets, plugs, or reliability.

 Wide use: It can be applied to wireless LAN access points, IP Phones, IP cameras, network hubs, embedded computers etc.

TL-SG2424P/TL-SG2210P is a Power Sourcing Equipment (PSE). All the Auto-Negotiation RJ45 ports on the switch support Power over Ethernet (PoE) function, which can automatically detect and supply power for those powered devices (PDs) complying with IEEE 802.3af (for

TL-SG2210P/TL-SG2424P) and IEEE 802.3at (for TL-SG2424P). The maximum power

TL-SG2210P can supply is 53W and the maximum power each PoE port can supply is 15.4W. The maximum power TL-SG2424P can supply is 180W and the maximum power each PoE port can supply is 30W.

PoE function can be configured in the two sections, PoE Config and PoE Time-Range.

11.1 PoE Config

All the RJ45 ports on the switch can be configured to supply power for the powered devices that comply with IEEE 802.3af (for TL-SG2210P and TL-SG2424P) and IEEE 802.3at (for

TL-SG2424P). As the power every port or the system can provide is limited, some attributes should be set to make full use of the power and guarantee the adequate power to the linked PDs.

128

When the power exceeds the maximum power limit or the power is inadequate to power the device, the switch may disconnect the power supply to the PD linked to the port with lower priority. When detecting a PD is unplugged, the switch will stop supplying the power to the PD.

PoE Config, mainly for PoE attributes configuration, is implemented on PoE Config and PoE

Profile pages.

11.1.1 PoE Config

On this page, you can configure the parameters to implement PoE function.

Choose the menu PoE→PoE Config→PoE Config to load the following page.

For TL-SG2210P:

Figure 11-1 PoE Config for TL-SG2210P

The following items are displayed on this screen:

 Global Config

System Power Limit: Specify the max power the PoE switch can supply.

System Power

Consumption:

Displays the PoE switch's real time system power consumption.

System Power Displays the PoE switch's real time remaining system power.

Remain:

Port Config

Port Select:

Select:

Port:

PoE Status:

PoE Priority:

Click the Select button to quick-select the corresponding entry based on the port number you entered.

Select the desired port to configure its parameters.

Displays the port number.

Select to disable/enable the PoE feature for the corresponding port. If set enable, the corresponding port can supply power to the linked PD (Powered Device).

The priority levels include High, Middle and Low in descending order. When the supply power exceeds the system power limit, the PD linked to the port with lower priority will be disconnected.

129

Power Limit

(0.1w-15.4w):

Time Range:

PoE Profile:

Power (W):

Current (mA):

Voltage (V):

PD Class:

Power Status:

For TL-SG2424P:

Defines the max power the corresponding port can supply. Class1 represents 4w, Class2 represents 7w and Class3 represents

15.4w.

Select the time range for the PoE port to supply power. If No limit is selected, the PoE port will supply power all the time.

Select the profile you want to apply to the selected port. If a PoE

Profile is selected, the three attributes including PoE Status, PoE

Priority and Power Limit are not available.

Displays the port's real time power supply.

Displays the port's real time current.

Displays the port's real time voltage.

Displays the class the linked PD (Powered Device) belongs to.

Displays the port's real time power status.

Figure 11-2 PoE Config for TL-SG2424P

The following items are displayed on this screen:

 Global Config

System Power Limit: Specify the max power the PoE switch can supply.

System Power

Consumption:

Displays the PoE switch's real time system power consumption.

System Power

Remain:

Displays the PoE switch's real time remaining system power.

130

 Port Config

Port Select:

Select:

Port:

PoE Status:

PoE Priority:

Power Limit

(0.1w-30w):

Time Range:

PoE Profile:

Power (W):

Current (mA):

Voltage (V):

PD Class:

Power Status:

Click the Select button to quick-select the corresponding entry based on the port number you entered.

Select the desired port to configure its parameters.

Displays the port number.

Select to disable/enable the PoE feature for the corresponding port. If set enable, the corresponding port can supply power to the linked PD (Powered Device).

The priority levels include High, Middle and Low in descending order. When the supply power exceeds the system power limit, the PD linked to the port with lower priority will be disconnected.

Defines the max power the corresponding port can supply. Class1 represents 4w, Class2 represents 7w, Class3 represents 15.4w

and Class4 represents 30w.

Select the time range for the PoE port to supply power. If No limit is selected, the PoE port will supply power all the time.

Select the profile you want to apply to the selected port. If a PoE

Profile is selected, the three attributes including PoE Status, PoE

Priority and Power Limit are not available.

Displays the port's real time power supply.

Displays the port's real time current.

Displays the port's real time voltage.

Displays the class the linked PD (Powered Device) belongs to.

Displays the port's real time power status.

11.1.2 PoE Profile

PoE (Power over Ethernet) Profile is a short cut for the configuration of the PoE port. You can create some profiles to be applied to the ports. In a profile, the PoE status, PoE priority and Power limit are configured.

Choose the menu PoE→PoE Config→Profile Profile to load the following page.

131

Figure 11-3 Profile Config

The following items are displayed on this screen:

Create PoE Profile

Profile Name:

PoE Status:

PoE Priority:

Power Limit:

Enter the name of the profile.

Select to the enable/disable PoE feature for the corresponding port. If set enable, the port may supply power to the linked PD

(Power Device).

The priority levels include High, Middle and Low in descending order. When the supply power exceeds the system power limit, the PD linked to the port with lower priority will be disconnected.

Defines the max power the corresponding port can supply. Class1 represents 4w, Class2 represents 7w and Class3 represents

15.4w. (for TL-SG2210P)

Defines the max power the corresponding port can supply. Class1 represents 4w, Class2 represents 7w, Class3 represents 15.4w, and Class4 represents 30w. (for TL-SG2424P)

 PoE Profile

Select:

Profile Name:

PoE Status:

PoE Priority:

Power Limit:

Select the desired profile to delete.

Displays the name of the profile.

Displays the PoE status of the port in the profile.

Displays the PoE priority of the port in the profile.

Displays the max power the port in the profile can supply.

11.2 PoE Time-Range

A time-range based PoE enables you to implement PoE power supply by differentiating the time-ranges. A time-range can be specified for each port. The port will not supply power when the specified time-range is configured and the system time is not within the time-range.

On this switch absolute time, week time and holiday can be configured. Configure an absolute time section in the form of “the start date to the end date” to make the port based on this time range

132

supply power; configure a week time section to make the port supply based on this time range on the fixed days of the week; configure a holiday section and select Exclude Holiday to make the port based on this time range not supply power on some special days. In each time-range, four time-slices can be configured.

The Time-Range configuration can be implemented on PoE Time-Range Summary, PoE

Time-Range Create and PoE Holiday Config pages.

11.2.1 Time-Range Summary

On this page you can view or delete the current time-ranges.

Choose the menu PoE→PoE Time-Range→PoE Time-Range Summary to load the following page.

Figure 11-4 Time-Range Table

The following items are displayed on this screen:

 Time-Range Table

Select:

Index:

Time-Range Name:

Slice:

Mode:

Operation:

Select the desired entry to delete the corresponding time-range.

Displays the index of the time-range.

Displays the name of the time-range.

Displays the time-slice of the time-range.

Displays the mode the time-range adopts.

Click Edit to modify this time-range and click Detail to display the complete information of this time–range.

11.2.2 PoE Time-Range Create

On this page you can create time-ranges.

Choose the menu PoE→PoE Time-Range→PoE Time-Range Create to load the following page.

133

Figure 11-5 Time-Range Create

Note:

To successfully configure time-ranges, please firstly specify time-slices and then time-ranges.

The following items are displayed on this screen:

 Create Time-Range

Name:

Exclude Holiday:

Absolute:

Week:

Enter the name of the time-range for time identification.

Select Exclude Holiday, and the port based on this time-range may not supply power when the system time is within the holiday

Select Absolute to configure absolute time-range. The port based on this time-range will supply power based on this time-range when the system time is within the absolute time-range.

Select Week to configure week time-range. The port based on this time-range will supply power based on this time-range when the system time is within the week time-range.

 Create Time-Slice

Set the start time of the time-slice.

Set the end time of the time-slice.

Start Time:

End Time:

Time-Slice Table

Index:

Start Time:

End Time:

Delete:

Displays the index of the time-slice.

Displays the start time of the time-slice.

Displays the end time of the time-slice.

Click the Delete button to delete the corresponding time-slice.

11.2.3 PoE Holiday Config

Holiday mode is applied as a different secured access control policy from the week mode. On this page you can define holidays according to your work arrangement.

134

Choose the menu PoE→PoE Time-Range→PoE Holiday Create to load the following page.

Figure 11-6 Holiday Configuration

The following entries are displayed on this screen:

 Create Holiday

Start Date:

End Date:

Holiday Name:

Holiday Table

Specify the start date of the holiday.

Specify the end date of the holiday.

Enter the name of the holiday.

Select:

Index:

Holiday Name:

Start Date:

End Date:

Select the desired entry to delete the corresponding holiday.

Displays the index of the holiday.

Displays the name of the holiday.

Displays the start date of the holiday.

Displays the end date of the holiday.

Return to CONTENTS

135

Chapter 12 SNMP

SNMP Overview

SNMP (Simple Network Management Protocol) has gained the most extensive application on the

UDP/IP networks. SNMP provides a management frame to monitor and maintain the network devices. It is used for automatically managing the various network devices no matter the physical differences of the devices. Currently, the most network management systems are based on SNMP.

SNMP is simply designed and convenient for use with no need of complex fulfillment procedures and too much network resources. With SNMP function enabled, network administrators can easily monitor the network performance, detect the malfunctions and configure the network devices. In the meantime, they can locate faults promptly and implement the fault diagnosis, capacity planning and report generating.

SNMP Management Frame

SNMP management frame includes three network elements: SNMP Management Station, SNMP

Agent and MIB (Management Information Base).

SNMP Management Station: SNMP Management Station is the workstation for running the

SNMP client program, providing a friendly management interface for the administrator to manage the most network devices conveniently.

SNMP Agent: Agent is the server software operated on network devices with the responsibility of receiving and processing the request packets from SNMP Management Station. In the meanwhile,

Agent will inform the SNMP Management Station of the events whenever the device status changes or the device encounters any abnormalities such as device reboot.

MIB: MIB is the set of the managed objects. MIB defines a few attributes of the managed objects, including the names, the access rights, and the data types. Every SNMP Agent has its own MIB.

The SNMP Management station can read/write the MIB objects based on its management right.

SNMP Management Station is the manager of SNMP network while SNMP Agent is the managed object. The information between SNMP Management Station and SNMP Agent are exchanged through SNMP (Simple Network Management Protocol). The relationship among SNMP

Management Station, SNMP Agent and MIB is illustrated in the following figure.

Figure 12-1 Relationship among SNMP Network Elements

SNMP Versions

This switch supports SNMP v3, and is compatible with SNMP v1 and SNMP v2c. The SNMP versions adopted by SNMP Management Station and SNMP Agent should be the same.

Otherwise, SNMP Management Station and SNMP Agent can not communicate with each other

136

normally. You can select the management mode with proper security level according to your actual application requirement.

SNMP v1: SNMP v1 adopts Community Name authentication. The community name is used to define the relation between SNMP Management Station and SNMP Agent. The SNMP packets failing to pass community name authentication are discarded. The community name can limit access to SNMP Agent from SNMP NMS, functioning as a password.

SNMP v2c: SNMP v2c also adopts community name authentication. It is compatible with SNMP v1 while enlarges the function of SNMP v1.

SNMP v3: Based on SNMP v1 and SNMP v2c, SNMP v3 extremely enhances the security and manageability. It adopts VACM (View-based Access Control Model) and USM (User-Based

Security Model) authentication. The user can configure the authentication and the encryption functions. The authentication function is to limit the access of the illegal user by authenticating the senders of packets. Meanwhile, the encryption function is used to encrypt the packets transmitted between SNMP Management Station and SNMP Agent so as to prevent any information being stolen. The multiple combinations of authentication function and encryption function can guarantee a more reliable communication between SNMP Management station and SNMP Agent.

 MIB Introduction

To uniquely identify the management objects of the device in SNMP messages, SNMP adopts the hierarchical architecture to identify the managed objects. It is like a tree, and each tree node represents a managed object, as shown in the following figure. Thus the object can be identified with the unique path starting from the root and indicated by a string of numbers. The number string is the Object Identifier of the managed object. In the following figure, the OID of the managed object B is {1.2.1.1}. While the OID of the managed object A is {1.2.1.1.5}.

Figure 12-2 Architecture of the MIB tree

SNMP Configuration Outline

The SNMP View is created for the SNMP Management Station to manage MIB objects. The managed object, uniquely identified by OID, can be set to under or out of the management of

SNMP Management Station by configuring its view type (included/excluded). The OID of managed object can be found on the SNMP client program running on the SNMP Management Station.

2. Create SNMP Group

After creating the SNMP View, it’s required to create a SNMP Group. The Group Name, Security

Model and Security Level compose the identifier of the SNMP Group. The Groups with these three items the same are considered to be the same. You can configure SNMP Group to control the network access by providing the users in various groups with different management rights via the

Read View, Write View and Notify View.

137

3. Create SNMP User

The User configured in a SNMP Group can manage the switch via the client program on management station. The specified User Name and the Auth/Privacy Password are used for

SNMP Management Station to access the SNMP Agent, functioning as the password.

SNMP module is used to configure the SNMP function of the switch, including three submenus:

SNMP Config, Notification and RMON.

12.1 SNMP Config

The SNMP Config can be implemented on the Global Config, SNMP View, SNMP Group,

SNMP User and SNMP Community pages.

12.1.1 Global Config

To enable SNMP function, please configure the SNMP function globally on this page.

Choose the menu SNMP→SNMP Config→Global Config to load the following page.

Figure 12-3 Global Config

The following entries are displayed on this screen:

 Global Config

SNMP:

Local Engine

Enable/Disable the SNMP function.

Local Engine ID: Specify the switch’s Engine ID for the remote clients. The

Engine ID is a unique alphanumeric string used to identify the

SNMP engine on the switch.

 Remote Engine

Remote Engine ID: Specify the Remote Engine ID for switch. The Engine ID is a unique alphanumeric string used to identify the SNMP engine on the remote device which receives traps and informs from switch.

138

Note:

The amount of Engine ID characters must be even.

12.1.2 SNMP View

The OID (Object Identifier) of the SNMP packets is used to describe the managed objects of the switch, and the MIB (Management Information Base) is the set of the OIDs. The SNMP View is created for the SNMP management station to manage MIB objects.

Choose the menu SNMP→SNMP Config→SNMP View to load the following page.

Figure 12-4 SNMP View

The following entries are displayed on this screen:

View Config

View Name:

MIB Object ID:

View Type:

Give a name to the View for identification. Each View can include several entries with the same name.

Enter the Object Identifier (OID) for the entry of View.

Select the type for the view entry.

 Include: The view entry can be managed by the SNMP management station.

 Exclude: The view entry can not be managed by the SNMP management station.

View Table

Select:

View Name:

View Type:

MIB Object ID:

Select the desired entry to delete the corresponding view. All the entries of a View will be deleted together.

Displays the name of the View entry.

Displays the type of the View entry.

Displays the OID of the View entry.

139

12.1.3 SNMP Group

On this page, you can configure SNMP Group to control the network access by providing the users in various groups with different management rights via the Read View, Write View and Notify View.

Choose the menu SNMP→SNMP Config→SNMP Group to load the following page.

Figure 12-5 SNMP Group

The following entries are displayed on this screen:

Group Config

Group Name:

Security Model:

Security Level:

Read View:

Enter the SNMP Group name. The Group Name, Security Model and Security Level compose the identifier of the SNMP Group.

The Groups with these three items the same are considered to be the same.

Select the Security Model for the SNMP Group.

 v1: SNMPv1 is defined for the group. In this model, the

Community Name is used for authentication. SNMP v1 can be configured on the SNMP Community page directly.

 v2c: SNMPv2c is defined for the group. In this model, the

Community Name is used for authentication. SNMP v2c can be configured on the SNMP Community page directly.

 v3: SNMPv3 is defined for the group. In this model, the USM mechanism is used for authentication. If SNMPv3 is enabled, the Security Level field is enabled for configuration.

Select the Security Level for the SNMP v3 Group.

 noAuthNoPriv: No authentication and no privacy security level is used.

 authNoPriv: Only the authentication security level is used.

 authPriv: Both the authentication and the privacy security levels are used.

Select the View to be the Read View. The management access is restricted to read-only, and changes cannot be made to the assigned SNMP View.

140

Write View:

Notify View:

Select the View to be the Write View. The management access is writing only and changes can be made to the assigned SNMP

View. The View defined both as the Read View and the Write View can be read and modified.

Select the View to be the Notify View. The management station can receive trap messages of the assigned SNMP view generated by the switch's SNMP agent.

 Group Table

Select:

Group Name:

Security Model:

Security Level:

Read View:

Write View:

Notify View:

Operation:

Select the desired entry to delete the corresponding group. It is multi-optional.

Displays the Group Name here.

Displays the Security Model of the group.

Displays the Security Level of the group.

Displays the Read View name in the entry.

Displays the Write View name in the entry.

Displays the Notify View name in the entry.

Click the Edit button to modify the Views in the entry and click the

Modify button to apply.

Note:

Every Group should contain a Read View. The default Read View is viewDefault.

12.1.4 SNMP User

The User in a SNMP Group can manage the switch via the management station software. The

User and its Group have the same security level and access right. You can configure the SNMP

User on this page.

Choose the menu SNMP→SNMP Config→SNMP User to load the following page.

Figure 12-6 SNMP User

141

The following entries are displayed on this screen:

User Config

User Name:

User Type:

Group Name:

Security Model:

Security Level:

Auth Mode:

Auth Password:

Privacy Mode:

Enter the User Name here.

Select the type for the User.

 Local User: Indicates that the user is connected to a local SNMP engine.

 Remote User: Indicates that the user is connected to a remote SNMP engine.

Select the Group Name of the User. The User is classified to the corresponding Group according to its Group Name,

Security Model and Security Level.

Select the Security Model for the User.

Select the Security Level for the SNMP v3 User.

Select the Authentication Mode for the SNMP v3 User.

 None: No authentication method is used.

 MD5: The port authentication is performed via

HMAC-MD5 algorithm.

 SHA: The port authentication is performed via SHA

(Secure Hash Algorithm). This authentication mode has a higher security than MD5 mode.

Enter the password for authentication.

Select the Privacy Mode for the SNMP v3 User.

 None: No privacy method is used.

 DES: DES encryption method is used.

Enter the Privacy Password.

Privacy Password:

User Table

Select:

User Name:

User Type:

Group Name:

Security Model:

Security Level:

Auth Mode:

Privacy Mode:

Operation:

Select the desired entry to delete the corresponding User. It is multi-optional.

Displays the name of the User.

Displays the User Type.

Displays the Group Name of the User.

Displays the Security Model of the User.

Displays the Security Level of the User.

Displays the Authentication Mode of the User.

Displays the Privacy Mode of the User.

Click the Edit button to modify the Group of the User and click the Modify button to apply.

Note:

The SNMP User and its Group should have the same Security Model and Security Level.

142

12.1.5 SNMP Community

SNMP v1 and SNMP v2c adopt community name authentication. The community name can limit access to the SNMP agent from SNMP network management station, functioning as a password. If

SNMP v1 or SNMP v2c is employed, you can directly configure the SNMP Community on this page without configuring SNMP Group and User.

Choose the menu SNMP→SNMP Config→SNMP Community to load the following page.

Figure 12-7 SNMP Community

The following entries are displayed on this screen:

Community Config

Community Name:

Access:

MIB View:

Enter the Community Name here.

Defines the access rights of the community.

read-only: Management right of the Community is restricted to read-only, and changes cannot be made to the corresponding View.

read-write: Management right of the Community is read-write and changes can be made to the corresponding

View.

Select the MIB View for the community to access.

 Community Table

Select:

Community Name:

Access:

MIB View:

Operation:

Select the desired entry to delete the corresponding Community. It is multi-optional.

Displays the Community Name here.

Displays the right of the Community to access the View.

Displays the Views which the Community can access.

Click the Edit button to modify the MIB View and the Access right of the Community, and then click the Modify button to apply.

Note:

The default MIB View of SNMP Community is viewDefault.

143

Configuration Procedure:

If SNMPv3 is employed, please take the following steps:

Step Operation

2

3

4

Create SNMP View.

Create SNMP Group.

Create SNMP User.

Description

Required. On the SNMP→SNMP Config→Global

Config page, enable SNMP function globally.

Required. On the SNMP→SNMP Config→SNMP

View page, create SNMP View of the management agent. The default View Name is viewDefault and the default OID is 1.

Required. On the SNMP→SNMP Config→SNMP

Group page, create SNMP Group for SNMPv3 and specify SNMP Views with various access levels for

SNMP Group.

Required. On the SNMP→SNMP Config→SNMP

User page, create SNMP User in the Group and configure the auth/privacy mode and auth/privacy password for the User.

 If SNMPv1 or SNMPv2c is employed, please take the following steps:

Step

1

2

Operation

Enable SNMP function globally.

Create SNMP View.

Description

Required. On the SNMP→SNMP

Config→Global Config page, enable SNMP function globally.

Required. On the SNMP→SNMP Config→SNMP

View page, create SNMP View of the management agent. The default View Name is viewDefault and the default OID is 1.

3

Community directly.

Configure access level for the User. Create SNMP

Group and SNMP

User.

Create SNMP Community directly.

On the SNMP→SNMP Config→SNMP

Community page, create SNMP Community based on SNMP v1 and SNMP v2c.

Create SNMP Group and SNMP User.

Similar to the configuration way based on

SNMPv3, you can create SNMP Group and

SNMP User of SNMP v1/v2c. The User name can limit access to the SNMP agent from SNMP network management station, functioning as a community name. The users can manage the device via the Read

View, Write View and Notify View defined in the SNMP Group.

144

12.2 Notification

With the Notification function enabled, the switch can initiatively report to the management station about the important events that occur on the Views (e.g., the managed device is rebooted), which allows the management station to monitor and process the events in time.

The notification information includes the following two types:

Trap : Trap is the information that the managed device initiatively sends to the Network management station without request.

Inform:Inform packet is sent to inform the management station and ask for the reply. The switch will resend the inform request if it doesn’t get the response from the management station during the Timeout interval, and it will terminate resending the inform request if the resending times reach the specified Retry times. The Inform type, employed on SNMPv2c and SNMPv3, has a higher security than the Trap type.

On this page, you can configure the notification function of SNMP.

Choose the menu SNMP→Notification→Notification to load the following page.

Figure 12-8 Notification Config

The following entries are displayed on this screen:

Create Notification

IP Address:

UDP Port:

User:

Security Model:

Security Level:

Enter the IP Address of the management Host.

Enter the number of the UDP port used to send notifications.

The UDP port functions with the IP address for the notification sending. The default is 162.

Enter the User name of the management station.

Select the Security Model of the management station.

Select the Security Level for the SNMP v3 User.

noAuthNoPriv: No authentication and no privacy security level are used.

authNoPriv: Only the authentication security level is used.

authPriv: Both the authentication and the privacy security levels are used.

145

Type:

Retry:

Timeout:

Select the type for the notifications.

Trap: Indicates traps are sent.

Inform: Indicates informs are sent. The Inform type has a higher security than the Trap type.

Specify the amount of times the switch resends an inform request. The switch will resend the inform request if it doesn’t get the response from the management station during the

Timeout interval, and it will terminate resending the inform request if the resending times reach the specified Retry times.

Specify the maximum time for the switch to wait for the response from the management station before resending a request.

 Notification Table

Select:

IP Address:

UDP Port:

User:

Security Model:

Security Level:

Type:

Timeout:

Retry:

Operation:

Select the desired entry to delete the corresponding management station.

Displays the IP Address of the management host.

Displays the UDP port used to send notifications.

Displays the User name of the management station.

Displays the Security Model of the management station.

Displays the Security Level for the SNMP v3 User.

Displays the type of the notifications.

Displays the maximum time for the switch to wait for the response from the management station before resending a request.

Displays the amount of times the switch resends an inform request.

Click the Edit button to modify the corresponding entry and click the Modify button to apply.

12.3 RMON

RMON (Remote Monitoring) based on SNMP (Simple Network Management Protocol) architecture, functions to monitor the network. RMON is currently a commonly used network management standard defined by Internet Engineering Task Force (IETF), which is mainly used to monitor the data traffic across a network segment or even the entire network so as to enable the network administrator to take the protection measures in time to avoid any network malfunction. In addition, RMON MIB records network statistics information of network performance and malfunction periodically, based on which the management station can monitor network at any time effectively. RMON is helpful for network administrator to manage the large-scale network since it reduces the communication traffic between management station and managed agent.

RMON Group

This switch supports the following four RMON Groups defined on the RMON standard (RFC1757):

History Group, Event Group, Statistic Group and Alarm Group.

146

RMON Group Function

History Group After a history group is configured, the switch collects and records network statistics information periodically, based on which the management station can monitor network effectively.

Event Group Event Group is used to define RMON events. Alarms occur when an event is detected.

Statistic Group Statistic Group is set to monitor the statistic of alarm variables on the specific ports.

Alarm Group Alarm Group is configured to monitor the specific alarm variables. When the value of a monitored variable exceeds the threshold, an alarm event is generated, which triggers the switch to act in the set way.

The RMON Groups can be configured on the History Control, Event Config and Alarm Config pages.

12.3.1 History Control

On this page, you can configure the History Group for RMON.

Choose the menu SNMP→RMON→History Control to load the following page.

Figure 12-9 History Control

The following entries are displayed on this screen:

History Control Table

Select:

Index:

Port:

Interval:

Owner:

Select the desired entry for configuration.

Displays the index number of the entry.

Specify the port from which the history samples were taken.

Specify the interval to take samplings from the port.

Enter the name of the device or user that defined the entry.

147

Status: Select Enable/Disable the corresponding sampling entry.

12.3.2 Event Config

On this page, you can configure the RMON events.

Choose the menu SNMP→RMON→Event Config to load the following page.

Figure 12-10 Event Config

The following entries are displayed on this screen:

 Event Table

Select:

Index:

User:

Description:

Type:

Owner:

Status:

Select the desired entry for configuration.

Displays the index number of the entry.

Enter the name of the User or the community to which the event belongs.

Give a description to the event for identification.

Select the event type, which determines the act way of the network device in response to an event.

 None: No processing.

 Log: Logging the event.

 Notify: Sending trap messages to the management station.

 Log&Notify: Logging the event and sending trap messages to the management station.

Enter the name of the device or user that defined the entry.

Select Enable/Disable the corresponding event entry.

148

12.3.3 Alarm Config

On this page, you can configure Statistic Group and Alarm Group for RMON.

Choose the menu SNMP→RMON→Alarm Config to load the following page.

Figure 12-11 Alarm Config

The following entries are displayed on this screen:

Alarm Table

Select: Select the desired entry for configuration.

Index:

Variable:

Displays the index number of the entry.

Select the alarm variables from the pull-down list.

Port:

Sample Type:

Rising Threshold:

Select the port on which the Alarm entry acts.

Specify the sampling method for the selected variable and comparing the value against the thresholds.

Absolute: Compares the values directly with the thresholds at the end of the sampling interval.

Delta: Subtracts the last sampled value from the current value. The difference in the values is compared to the threshold.

Enter the rising counter value that triggers the Rising Threshold alarm.

Rising Event:

Falling Threshold:

Falling Event:

Alarm Type:

Select the index of the corresponding event which will be triggered if the sampled value is larger than the Rising

Threshold.

Enter the falling counter value that triggers the Falling Threshold alarm.

Select the index of the corresponding event which will be triggered if the sampled value is lower than the Falling

Threshold.

Specify the type of the alarm.

All: The alarm event will be triggered either the sampled value exceeds the Rising Threshold or is under the Falling

Threshold.

149

Interval:

Owner:

Status:

Rising: When the sampled value exceeds the Rising

Threshold, an alarm event is triggered.

Falling: When the sampled value is under the Falling

Threshold, an alarm event is triggered.

Enter the alarm interval time in seconds.

Enter the name of the device or user that defined the entry.

Select Enable/Disable the corresponding alarm entry.

Note:

When alarm variables exceed the Threshold on the same direction continuously for several times, an alarm event will only be generated on the first time, that is, the Rising Alarm and Falling Alarm are triggered alternately for that the alarm following to Rising Alarm is certainly a Falling Alarm and vice versa.

Return to CONTENTS

150

Chapter 13 LLDP

Note:

Only TL-SG2210P and TL-SG2424P support LLDP function.

LLDP (Link Layer Discovery Protocol) is a Layer 2 protocol that is used for network devices to advertise their own device information periodically to neighbors on the same IEEE 802 local area network. The advertised information, including details such as device identification, capabilities and configuration settings, is represented in TLV (Type/Length/Value) format according to the

IEEE 802.1ab standard, and these TLVs are encapsulated in LLDPDU (Link Layer Discovery

Protocol Data Unit). The LLDPDU distributed via LLDP is stored by its recipients in a standard MIB

(Management Information Base), making it possible for the information to be accessed by a

Network Management System (NMS) using a management protocol such as the Simple Network

Management Protocol (SNMP).

An IETF Standard MIB, as well as a number of vendor specific MIBs, have been created to describe a network's physical topology and associated systems within that topology. However, there is no standard protocol for populating these MIBs or communicating this information among stations on the IEEE 802 LAN. LLDP protocol specifies a set. The device running LLDP can automatically discover and learn about the neighbors, allowing for interoperability between the network devices of different vendors. This protocol allows two systems running different network layer protocols to learn about each other.

LLDP-MED (Link Layer Discovery Protocol for Media Endpoint Devices) is an extension of LLDP intended for managing endpoint devices such as Voice over IP phones and network switches. The

LLDP-MED TLVs advertise information such as network policy, power via MDI, inventory management, and device location details.

The LLDP and LLDP-MED information can be used by SNMP applications to simplify troubleshooting, enhance network management, and maintain an accurate network topology.

LLDPDU Format

Each LLDPDU includes an ordered sequence of three mandatory TLVs followed by one or more optional TLVs plus an End of LLDPDU TLV, as shown in the figure below. Chassis ID TLV, Port ID

TLV, TTL TLV and End TLV are the four mandatory TLVs for a LLDPDU. Optional TLVs provide various details about the LLDP agent advertising them and they are selected by network management.

The maximum length of the LLDPDU shall be the maximum information field length allowed by the particular transmission rate and protocol. In IEEE 802.3 MACs, for example, the maximum

LLDPDU length is the maximum data field length for the basic, untagged MAC frame (1500 octets).

LLDP Working Mechanism

The transmission and the reception of LLDPDUs can be separately enabled for every port, making it possible to configure an implementation to restrict the port either to transmit only or receive only,

151

or to allow the port to both transmit and receive LLDPDUs. Four LLDP admin statuses are supported by each port.

 Tx&Rx: the port can both transmit and receive LLDPDUs.

 Rx_Only: the port can receive LLDPDUs only.

 Tx_Only: the port can transmit LLDPDUs only.

 Disable: the port cannot transmit or receive LLDPDUs.

2) LLDPDU transmission mechanism

 If the ports are working in TxRx or Tx mode, they will advertise local information by sending LLDPDUs periodically.

 If there is a change in the local device, the change notification will be advertised. To prevent a series of successive LLDPDUs transmissions during a short period due to frequent changes in local device, a transmission delay timer is set by network management to ensure that there is a defined minimum time between successive LLDP frame transmissions.

 If the LLDP admin status of the port is changed from Disable/Rx to TxRx/Tx, the Fast

Start Mechanism will be active, the transmit interval turns to be 1 second, several

LLDPDUs will be sent out, and then the transmit interval comes back to the regular interval.

3) LLDPDU receipt mechanism

When a port is working in TxRx or Rx mode, the device will check the validity of the received

LLDPDUs and the attached TLVs, save this neighbor information to the local device and then set the aging time of this information according to the TTL value of TTL (Time To Live) TLV. Once the

TTL is 0, this neighbor information will be aged out immediately.

The aging time of the local information in the neighbor device is determined by TTL. Hold

Multiplier is a multiplier on the Transmit Interval that determines the actual TTL value used in an

LLDPDU. TTL = Hold Multiplier * Transmit Interval.

TLV

TLV refers to Type/Length/Value and is contained in a LLDPDU. Type identifies what kind of information is being sent, Length indicates the length of information string in octets and Value is the actual information to be sent. The basic TLV Format is shown as follows:

Each TLV is identified by a unique TLV type value that indicates the particular kind of information contained in the TLV.

152

The following table shows the details about the currently defined TLVs.

TLV type

0

TLV Name Description Usage in

LLDPDU

End of LLDPDU Mark the end of the TLV sequence in LLDPDUs.

Any information following an End Of LLDPDU

TLV shall be ignored.

Mandatory

Mandatory device.

LLDP frame. When the device does not advertise

MED TLV, this field displays the port name of the port; when the device advertises MED TLV, this field displays the MAC address of the port.

Mandatory

Mandatory neighbor device is to regard the local information to be valid.

Port Description Identifies the description string of the port. Optional 4

5 System Name Identifies the system name.

6 System Identifies the system description.

Description

Optional

Optional

7 System Identifies the main functions of the system and

Capabilities the functions enabled.

Optional

Address corresponding interface number and OID (Object

Identifier). The management IP address is specified by the user.

Optional

Specific 802.1, IEEE 802.3, IETF, as well as individual software and equipment vendors, to define TLVs that advertise information to remote device.

Optional

Optional TLVs are grouped into two categories including basic management TLV and

Organizationally-specific TLV.

1) Basic Management TLV

A set of TLVs considered to be basic to the management of the network stations are required for all LLDP implementations.

2) Organizationally Specific TLV

Different organizations have defined various TLVs. For instance, Port VLAN ID TLV, Port and

Protocol VLAN ID TLV, VLAN Name TLV And Protocol Identity TLV are defined by IEEE 802.1, while MAC/PHY Configuration/Status TLV, Power Via MDI TLV, Link Aggregation TLV and

Maximum Frame TLV are defined by IEEE 802.3. Some specific TLVs are for LLDP-MED protocol, such as LLDP-MED Capabilities TLV, Network Policy TLV, Extended Power-via-MDI TLV,

Hardware Revision TLV and so on.

153

Note:

For detailed introduction of TLV, please refer to IEEE 802.1AB standard and ANSI/TIA-1057.

In TP-LINK switch, the following LLDP optional TLVs are supported.

Port Description TLV

System Capabilities TLV

System Description TLV

The System Capabilities TLV identifies the primary functions of the system and whether or not these primary functions are enabled.

The System Description TLV allows network management to advertise the system's description, which should include the full name and version identification of the system's hardware type, software operating system, and networking software.

System Name TLV The System Name TLV allows network management to advertise the system's assigned name, which should be the system's fully qualified domain name.

Management Address TLV The Management Address TLV identifies an address associated with the local LLDP agent that may be used to reach higher entities to assist discovery by network management.

Port VLAN ID TLV

The Port Description TLV allows network management to advertise the IEEE 802 LAN station's port description.

The Port VLAN ID TLV allows a VLAN bridge port to advertise the port's VLAN identifier (PVID) that will be associated with untagged or priority tagged frames.

Port And Protocol VLAN ID

TLV

The Port And Protocol VLAN ID TLV allows a bridge port to advertise a port and protocol VLAN ID.

VLAN Name TLV The VLAN Name TLV allows an IEEE 802.1Q-compatible IEEE

802 LAN station to advertise the assigned name of any VLAN with which it is configured.

Link Aggregation TLV The Link Aggregation TLV indicates whether the link is capable of being aggregated, whether the link is currently in an aggregation, and if in an aggregation, the port identification of the aggregation.

MAC/PHY

Configuration/Status TLV

Max Frame Size TLV

Power Via MDI TLV

The MAC/PHY Configuration/Status TLV identifies: a)The duplex and bit-rate capability of the sending IEEE 802.3 LAN node that is connected to the physical medium; b)The current duplex and bit-rate settings of the sending IEEE 802.3 LAN node; c)Whether these settings are the result of auto-negotiation during link initiation or of manual set override action.

The Maximum Frame Size TLV indicates the maximum frame size capability of the implemented MAC and PHY.

The Power Via MDI TLV allows network management to advertise and discover the MDI power support capabilities of the sending IEEE 802.3 LAN station.

154

The LLDP module is mainly for LLDP function configuration of the switch, including three submenus: Basic Config, Device Info, Device Statistics and LLDP-MED.

13.1 Basic Config

LLDP is configured on the Global Config and Port Config pages.

13.1.1 Global Config

On this page you can configure the LLDP parameters of the device globally.

Choose the menu LLDP→Basic Config→Global Config to load the following page.

Figure 13-1 LLDP Global Configuration

The following entries are displayed on this screen :

Global Config

Enable/disable LLDP function globally.

LLDP:

Parameters Config

Transmit Interval:

Hold Multiplier:

Transmit Delay:

Reinit Delay:

Notification Interval:

Enter the interval for the local device to transmit LLDPDU to its neighbors. The default value is 30.

Enter a multiplier on the Transmit Interval. It determines the actual

TTL (Time To Live) value used in an LLDPDU. TTL = Hold

Multiplier * Transmit Interval. The default value is 4.

Enter a value from 1 to 8192 in seconds to specify the time for the local device to transmit LLDPDU to its neighbors after changes occur so as to prevent LLDPDU being sent frequently. The default value is 2.

This parameter indicates the amount of delay from when LLDP status becomes "disable" until re-initialization will be attempted.

The default value is 3.

Specify the interval of Trap message which will be sent from local device to network management system. The default value is 5.

155

Fast Start Times: When the port's LLDP state transforms from Disable (or Rx_Only) to Tx&Rx (or Tx_Only), the fast start mechanism will be enabled, that is, the transmit interval will be shorten to a second, and several LLDPDUs will be sent out (the number of LLDPDUs equals this parameter). The default value is 3.

13.1.2 Port Config

On this page you can configure all ports' LLDP parameters.

Choose the menu LLDP→Basic Config→Port Config to load the following page.

Figure 13-2 LLDP Port Config

The following entries are displayed on this screen:

LLDP Port Config

Port Select:

Admin Status:

Notification Mode:

Included TLVs:

Details:

Select the desired port to configure.

Select the port’s LLDP operating mode:

Tx&Rx: send and receive LLDP frames.

Rx_Only: Only receive LLDP frames.

Tx_Only: Only send LLDP frames.

Disable: neither send nor receive LLDP frames.

Allows you to enable or disable the ports' SNMP notification. If enabled, the local device will notify the trap event to SNMP server.

Select TLVs to be included in outgoing LLDPDU.

Click the Detail button to display the included TLVs and select the desired TLVs.

156

13.2 Device Info

You can view the LLDP information of the local device and its neighbors on the Local Info and

Neighbor Info pages respectively.

13.2.1 Local Info

On this page you can see all ports' configuration and system information.

Choose the menu LLDP→Device Info→Local Info to load the following page.

Figure 13-3 LLDP Local Information

The following entries are displayed on this screen :

Auto Refresh

Auto Refresh: Enable/Disable the auto refresh function.

157

Refresh Rate: Specify the auto refresh rate.

 Local Info

Enter the desired port number and click Select to display the information of the corresponding port.

13.2.2 Neighbor Info

On this page you can get the information of the neighbors.

Choose the menu LLDP→Device Info→Neighbor Info to load the following page.

Figure 13-4 LLDP Neighbor Information

The following entries are displayed on this screen :

Auto Refresh

Auto Refresh:

Refresh Rate:

Neighbor Info

Port Select:

Enable/Disable the auto refresh function.

Specify the auto refresh rate.

Local Port:

System Name:

Chassis ID:

System Description:

Neighbor Port:

Information:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Displays the local port number connecting to the neighbor device.

Displays the system name of the neighbor device.

Displays the Chassis ID of the neighbor device.

Displays the system description of the neighbor device.

Displays the port number of the neighbor linking to local port.

Click Information to display the detailed information of the neighbor device.

13.3 Device Statistics

You can view the LLDP statistics of the local device through this feature.

Choose the menu LLDP→Device Statistics→Statistic Info to load the following page.

158

Figure 13-5 LLDP Statistic Information

The following entries are displayed on this screen :

Auto Refresh

Auto Refresh:

Refresh Rate:

Global Statistics

Last Update:

Total Inserts:

Total Deletes:

Total Drops:

Total Ageouts:

Neighbor Statistics

Port Select:

Enable/Disable the auto refresh function.

Specify the auto refresh rate.

Displays latest update time of the statistics.

Displays the number of neighbors inserted till last update time.

Displays the number of neighbors deleted by local device.

Displays the number of neighbors dropped by local device.

Displays the number of overtime neighbors in local device.

Click the Select button to quick-select the corresponding port

159

Port:

Transmit Total:

Receive Total:

Discards:

Errors:

Ageouts:

TLV Discards:

TLV Unknowns:

13.4 LLDP-MED

based on the port number you entered.

Displays local device's port number.

Displays the number of LLDPDUs sent by this port.

Displays the number of LLDPDUs received by this port.

Displays the number of LLDPDUs discarded by this port.

Displays the number of error LLDPDUs received by this port.

Displays the number of overtime neighbors linking to this port.

Displays the number of TLVs dropped by this port.

Displays the number of unknown TLVs received by this port.

LLDP-MED is an extension of LLDP intended for managing endpoint devices such as Voice over

IP phones and network switches. The LLDP-MED TLVs advertise information such as network policy, power via MDI, inventory management, and device location details.

Elements

LLDP-MED Device: Refers to any device which implements this Standard.

LLDP-MED Device Type: LLDP-MED devices are comprised of two primary device types:

Network Connectivity Devices and Endpoint Devices.

Network Connectivity Device: Refers to an LLDP-MED Device that provides access to the IEEE

802 based LAN infrastructure for LLDP-MED Endpoint Devices. Bridge is a Network Connectivity

Device.

Endpoint Device: Refers to an LLDP-MED Device at the network edge, providing some aspects of IP communications service, based on IEEE 802 LAN technology. Endpoint Devices may be a member of any of the Endpoint Device Classes. Endpoint Devices are composed of three defined

Classes: Class I, Class II and Class III.

Generic Endpoint Device (Class I): The most basic class of Endpoint Device.

Media Endpoint Device (Class II): The class of Endpoint Device that supports media stream capabilities.

Communication Device Endpoint (Class III): The class of Endpoint Device that directly supports end users of the IP communication system.

Network Policy TLV

Location Identification TLV

The Network Policy TLV allows both Network Connectivity

Devices and Endpoints to advertise VLAN configuration and associated Layer 2 and Layer 3 attributes that apply for a set of specific applications on that port.

The Location Identification TLV provides for advertisement of location identifier information to Communication Endpoint

Devices, based on configuration of the Network Connectivity

Device it's connected to. You can set the Location

Identification content in Location Identification Parameters. If

Location Identification TLV is included and Location

Identification Parameters isn't set, a default value is used in

Location Identification TLV.

160

Extended Power-Via-MDI TLV The Extended Power-Via-MDI TLV is intended to enable advanced power management between LLDP-MED Endpoint and Network Connectivity Devices, and it allows advertisement of fine grained power requirement details,

Endpoint power priority, as well as both Endpoint and Network

Connectivity Device power status.

Inventory TLV The Inventory TLV set contains seven basic Inventory management TLVs, that is, Hardware Revision TLV, Firmware

Revision TLV, Software Revision TLV, Serial Number TLV,

Manufacturer Name TLV, Model Name TLV and Asset ID

TLV. If support for any of the TLVs in the Inventory

Management set is implemented, then support for all

Inventory Management TLVs shall be implemented.

LLDP-MED is configured on the Global Config, Port Config, Local Info and Neighbor Info pages.

13.4.1 Global Config

On this page you can configure the LLDP-MED parameters of the device globally.

Choose the menu LLDP→LLDP-MED→Global Config to load the following page.

Figure 13-6 LLDP-MED Global Configuration

The following entries are displayed on this screen :

 LLDP-MED Parameters Config

Fast Start Count:

Device Class:

When LLDP-MED fast start mechanism is activated, multiple

LLDP-MED frames will be transmitted based on this parameter.

LLDP-MED devices are comprised of two primary device types:

Network Connectivity Devices and Endpoint Devices. In turn,

Endpoint Devices are composed of three defined Classes: Class I,

Class II and Class III. Bridge is a Network Connectivity Device.

13.4.2 Port Config

On this page you can configure all ports' LLDP-MED parameters.

Choose the menu LLDP→LLDP-MED→Port Config to load the following page.

161

Figure 13-7 LLDP-MED Port Configuration

The following entries are displayed on this screen :

LLDP-MED Port Config

Port Select:

LLDP-MED Status:

Included TLVs:

Detail:

Select the desired port to configure.

Configure the port's LLDP-MED status:

Enable: Enable the port's LLDP-MED status, and the port's Admin

Status will be changed to Tx&Rx.

Disable: Disable the port's LLDP-MED status.

Select TLVs to be included in outgoing LLDPDU.

Click the Detail button to display the included TLVs and select the desired TLVs.

162

Included TLVs

Select TLVs to be included in outgoing LLDPDU.

Location Identification Parameters

Configure the Location Identification TLV's content in outgoing LLDPDU of the port.

Emergency

Number:

Civic Address:

Emergency number is Emergency Call Service ELIN identifier, which is used during emergency call setup to a traditional CAMA or ISDN trunk-based PSAP.

The Civic address is defined to reuse the relevant sub-fields of the

DHCP option for Civic Address based Location Configuration

Information as specified by IETF.

13.4.3 Local Info

On this page you can see all ports' LLDP-MED configuration.

Choose the menu LLDP→LLDP-MED→Local Info to load the following page.

163

Figure 13-8 LLDP-MED Local Information

The following entries are displayed on this screen :

Auto Refresh

Auto Refresh:

Refresh Rate:

Enable/Disable the auto refresh function.

Specify the auto refresh rate.

Local Info

Enter the desired port number and click Select to display the information of the corresponding port.

13.4.4 Neighbor Info

On this page you can get the LLDP-MED information of the neighbors.

Choose the menu LLDP→LLDP-MED→Neighbor Info to load the following page.

164

Figure 13-9 LLDP-MED Neighbor Information

The following entries are displayed on this screen :

Auto Refresh

Auto Refresh:

Refresh Rate:

Neighbor Info

Enable/Disable the auto refresh function.

Specify the auto refresh rate.

Port Select:

Local Port:

Device Type:

Application Type:

Local Data Format:

Power Type:

Information:

Click the Select button to quick-select the corresponding port based on the port number you entered.

Displays the local port number connecting to the neighbor device.

Displays the device type of the neighbor.

Displays the application type of the neighbor. Application Type indicates the primary function of the applications defined for the network policy.

Displays the location identification of the neighbor.

Displays the power type of the neighbor device, Power Sourcing

Entity (PSE) or Powered Device (PD).

Click the Information button to display the detailed information of the corresponding neighbor.

Return to CONTENTS

165

Chapter 14 Maintenance

Maintenance module, assembling the commonly used system tools to manage the switch, provides the convenient method to locate and solve the network problem.

( 1) System Monitor: Monitor the utilization status of the memory and the CPU of switch.

( 2) Log: View the configuration parameters of the switch and find out the errors via the Logs.

( 3) Device Diagnostics: Cable Test tests the connection status of the cable to locate and diagnoses the trouble spot of the network. Loopback tests whether the ports of the switch and its peer device are available.

( 4) Network Diagnostics: Test whether the destination device is reachable and detect the route hops from the switch to the destination device.

14.1 System Monitor

System Monitor functions to display the utilization status of the memory and the CPU of switch via the data graph. The CPU utilization rate and the memory utilization rate should fluctuate stably around a specific value. If the CPU utilization rate or the memory utilization rate increases markedly, please detect whether the network is being attacked.

The System Monitor function is implemented on the CPU Monitor and Memory Monitor pages.

14.1.1 CPU Monitor

Choose the menu Maintenance→System Monitor→CPU Monitor to load the following page.

Figure 14-1 CPU Monitor

Click the Monitor button to enable the switch to monitor and display its CPU utilization rate every four seconds.

166

14.1.2 Memory Monitor

Choose the menu Maintenance→System Monitor→Memory Monitor to load the following page.

Figure 14-2 Memory Monitor

Click the Monitor button to enable the switch to monitor and display its Memory utilization rate every four seconds.

14.2 Log

The Log system of switch can record, classify and manage the system information effectively, providing powerful support for network administrator to monitor network operation and diagnose malfunction.

The Logs of switch are classified into the following eight levels.

Severity Level Description

167

Table 14-1 Log Level

The Log function is implemented on the Log Table, Local Log, Remote Log and Backup Log pages.

14.2.1 Log Table

The switch supports logs output to two directions, namely, log buffer and log file. The information in log buffer will be lost after the switch is rebooted or powered off whereas the information in log file will be kept effective even the switch is rebooted or powered off. Log Table displays the system log information in log buffer.

Choose the menu Maintenance→Log→Log Table to load the following page.

Figure 14-3 Log Table

The following entries are displayed on this screen:

Log Info

Index:

Time:

Module:

Severity:

Content:

Displays the index of the log information.

Displays the time when the log event occurs. The log can get the correct time after you configure on the System ->System

Info->System Time Web management page.

Displays the module which the log information belongs to. You can select a module from the drop-down list to display the corresponding log information.

Displays the severity level of the log information. You can select a severity level to display the log information whose severity level value is the same or smaller.

Displays the content of the log information.

Note:

1. The logs are classified into eight levels based on severity. The higher the information severity is, the lower the corresponding level is.

2. This page displays logs in the log buffer, and at most 512 logs are displayed.

168

14.2.2 Local Log

Local Log is the log information saved in switch. By default, all system logs are saved in log buffer and the logs with severities from level_0 to level_2 are saved in log file meanwhile. On this page, you can set the output channel for logs.

Choose the menu Maintenance→Log→Local Log to load the following page.

Figure 14-4 Local Log

The following entries are displayed on this screen:

Local Log Config

Select:

Channel:

Severity:

Status:

Select the desired entry to configure the corresponding local log.

 Log buffer: Indicates the RAM for saving system log. The inforamtion in the log buffer is displayed on the Log Table page. It will be lost when the switch is restarted.

 Log File: Indicates the flash sector for saving system log.

The information in the log file will not be lost after the switch is restarted and can be exported on the Backup Log page.

Specify the severity level of the log information output to each channel. Only the log with the same or smaller severity level value will be output.

Enable/Disable the channel.

14.2.3 Remote Log

Remote log feature enables the switch to send system logs to the Log Server. Log Server is to centralize the system logs from various devices for the administrator to monitor and manage the whole network.

Choose the menu Maintenance→Log→Remote Log to load the following page.

169

Host IP:

UDP Port:

Severity:

Status:

Figure 14-5 Log Host

The following entries are displayed on this screen:

Log Host

Index: Displays the index of the log host. The switch supports 4 log hosts.

Configure the IP for the log host.

Displays the UDP port used for receiving/sending log information. Here we use the standard port 514.

Specify the severity level of the log information sent to each log host. Only the log with the same or smaller severity level value will be sent to the corresponding log host.

Enable/Disable the log host.

Note:

The Log Server software is not provided. If necessary, please download it on the Internet.

14.2.4 Backup Log

Backup Log feature enables the system logs saved in the switch to be output as a file for device diagnosis and statistics analysis. When a critical error results in the breakdown of the system, you can export the logs to get some related important information about the error for device diagnosis after the switch is restarted.

Choose the menu Maintenance→Log→Backup Log to load the following page.

Figure 14-6 Backup Log

The following entry is displayed on this screen:

170

 Backup Log

Backup Log: Click the Backup Log button to save the log as a file to your computer.

Note:

It will take a few minutes to backup the log file. Please wait without any operation.

14.3 Device Diagnostics

This switch provides Cable Test and Loopback functions for device diagnose.

14.3.1 Cable Test

Cable Test functions to test the connection status of the cable connected to the switch, which facilitates you to locate and diagnose the trouble spot of the network.

Choose the menu Maintenance→Device Diagnostics→Cable Test to load the following page.

Figure 14-7 Cable Test

The following entries are displayed on this screen:

 Cable Test

Port:

Pair:

Status:

Length:

Error:

Select the port for cable testing.

Displays the Pair number.

Displays the connection status of the cable connected to the port. The test results of the cable include normal, close, open or impedance.

If the connection status is normal, here displays the length range of the cable.

If the connection status is close, open or impedance, here displays the error length of the cable.

Note:

1. The Length displayed here is the length of pair cable not that of the physical cable.

2. The test result is just for your reference.

171

14.3.2 Loopback

Loopback test function, looping the sender and the receiver of the signal, is used to test whether the port of the switch is available as well as to check and analyze the physical connection status of the port to help you locate and solve network malfunctions.

Choose the menu Maintenance→Device Diagnostics→Loopback to load the following page.

Figure 14-8 Loopback

The following entries are displayed on this screen:

 Loopback Type

Internal:

External:

Select Internal to test whether the port is available.

Select External to test whether the device connected to the port of the switch is available

Loopback Port

Loopback Port:

Test:

Select the desired port for loopback test.

Click the Test button to start the loopback test for the port.

14.4 Network Diagnostics

This switch provides Ping test and Tracert test functions for network Diagnostics.

14.4.1 Ping

Ping test function, testing the connectivity between the switch and one node of the network, facilitates you to test the network connectivity and reachability of the host so as to locate the network malfunctions.

Choose the menu Maintenance→Network Diagnostics→Ping to load the following page.

172

Figure 14-9 Ping

The following entries are displayed on this screen:

Ping Config

Destination IP:

Ping Times:

Data Size:

Interval:

Enter the IP address of the destination node for Ping test.

Enter the amount of times to send test data during Ping testing. The default value is recommended.

Enter the size of the sending data during Ping testing. The default value is recommended.

Specify the interval to send ICMP request packets. The default value is recommended.

14.4.2 Tracert

Tracert test function is used to test the connectivity of the gateways during its journey from the source to destination of the test data. When malfunctions occur to the network, you can locate trouble spot of the network with this tracert test.

Choose the menu Maintenance→Network Diagnostics→Tracert to load the following page.

Figure 14-10 Tracert

173

The following entries are displayed on this screen:

Tracert Config

Destination IP:

Max Hop:

Enter the IP address of the destination device.

Specify the maximum number of the route hops the test data can pass through.

Return to CONTENTS

174

Appendix A: Specifications

Standards

Transmission Rate

Transmission Medium

LED

IEEE802.3 10Base-T Ethernet

IEEE802.3u 100Base-TX/100Base-FX Fast Ethernet

IEEE802.3ab 1000Base-T Gigabit Ethernet

IEEE802.3z 1000Base-X Gigabit Ethernet

IEEE802.3x Flow Control

IEEE802.1p QoS

IEEE802.1q VLAN

Ethernet: 10Mbps HD,20Mbps FD

Fast Ethernet: 100Mbps HD,200Mbps FD

Gigabit Ethernet: 2000Mbps FD

10Base-T: UTP/STP of Cat. 3 or above

100Base-TX: UTP/STP of Cat. 5 or above

100Base-FX: MMF or SMF SFP Module (Optional)

1000Base-T: 4-pair UTP (≤100m) of Cat. 5, Cat. 5e, Cat.6

or above

1000Base-X: MMF or SMF SFP Module (Optional)

For TL-SG2210P: Power, System, Link/Act, PoE Status,

PoE MAX

For TL-SG2216/TL-SG2424: Power, System,1000Mbps,

Link/Act

For TL-SG2424P: Power, System, 10/100/1000Mbps Port

LED, Speed, PoE, PoE Max

For TL-SG2452: PWR, SYS, 10/100/1000Mbps

Transmission Method Store and Forward

Packets Forwarding Rate

10BASE-T:14881pps/port

100BASE-TX:148810pps/port

1000Base-T:1488095pps/port

Operating

Environment

Operating Temperature: 0 ~ 40 ℃

Storage Temperature: -40 ~ 70 ℃

Operating Humidity: 10% ~ 90% RH Non-condensing

Storage Humidity: 5% ~ 90% RH Non-condensing

Return to CONTENTS

175

Appendix B: Configuring the PCs

In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 2000.

First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary.

1) On the Windows taskbar, click the Start button, and then click Control Panel.

Connections tab in the appearing window.

3) Right click the icon that showed below, select Properties on the prompt page.

Figure B-1

4) In the prompt page that showed below, double click on the Internet Protocol (TCP/IP).

Figure B-2

176

this window by default.

Figure B-3

IP address is 192.168.0.1, specify IP address as 192.168.0.x (x is from 2 to 254), and the

Subnet mask as 255.255.255.0.

Now:

Click OK to save your settings.

Return to CONTENTS

177

Appendix C: Glossary

Boot Protocol (BOOTP)

BOOTP is used to provide bootup information for network devices, including IP address information, the address of the TFTP server that contains the devices system files, and the name of the boot file.

Class of Service (CoS)

CoS is supported by prioritizing packets based on the required level of service, and then placing them in the appropriate output queue. Data is transmitted from the queues using weighted round-robin service to enforce priority service and prevent blockage of lower-level queues. Priority may be set according to the port default, the packet’s priority bit (in the VLAN tag), TCP/UDP port number, or DSCP priority bit.

Differentiated Services Code Point (DSCP)

DSCP uses a six-bit tag to provide for up to 64 different forwarding behaviors. Based on network policies, different kinds of traffic can be marked for different kinds of forwarding. The DSCP bits are mapped to the Class of Service categories, and then into the output queues.

Domain Name Service (DNS)

A system used for translating host names for network nodes into IP addresses.

Dynamic Host Control Protocol (DHCP)

Provides a framework for passing configuration information to hosts on a TCP/IP network. DHCP is based on the Bootstrap Protocol (BOOTP), adding the capability of automatic allocation of reusable network addresses and additional configuration options..

IEEE 802.1D

Specifies a general method for the operation of MAC bridges, including the Spanning Tree

Protocol.

IEEE 802.1Q

VLAN Tagging—Defines Ethernet frame tags which carry VLAN information. It allows switches to assign endstations to different virtual LANs, and defines a standard way for VLANs to communicate across switched networks.

IEEE 802.1p

An IEEE standard for providing quality of service (QoS) in Ethernet networks. The standard uses packet tags that define up to eight traffic classes and allows switches to transmit packets based on the tagged priority value.

IEEE 802.3ac

Defines frame extensions for VLAN tagging.

IEEE 802.3x

Defines Ethernet frame start/stop requests and timers used for flow control on full-duplex links.

(Now incorporated in IEEE 802.3-2002)

178

Internet Group Management Protocol (IGMP)

A protocol through which hosts can register with their local router for multicast services. If there is more than one multicast switch/router on a given subnetwork, one of the devices is made the

“querier” and assumes responsibility for keeping track of group membership.

IGMP Snooping

Listening to IGMP Query and IGMP Report packets transferred between IP Multicast routers and

IP Multicast host groups to identify IP Multicast group members.

IGMP Query

On each subnetwork, one IGMP-capable device will act as the querier — that is, the device that asks all hosts to report on the IP multicast groups they wish to join or to which they already belong.

The elected querier will be the device with the lowest IP address in the subnetwork.

IP Multicast Filtering

It is a feature to allow or deny the Client to add the specified multicast group.

Multicast Switching

A process whereby the switch filters incoming multicast frames for services forwhich no attached host has registered, or forwards them to all ports contained within the designated multicast group.

Layer 2

Data Link layer in the ISO 7-Layer Data Communications Protocol. This is related directly to the hardware interface for network devices and passes on traffic based on MAC addresses.

Link Aggregation

See Port Trunk.

Management Information Base (MIB)

An acronym for Management Information Base. It is a set of database objects that contains information about a specific device.

MD5 Message-Digest Algorithm

An algorithm that is used to create digital signatures. It is intended for use with 32 bit machines and is safer than the MD4 algorithm, which has been broken. MD5 is a one-way hash function, meaning that it takes a message and converts it into a fixed string of digits, also called a message digest.

Network Time Protocol (NTP)

NTP provides the mechanisms to synchronize time across the network. The time servers operate in a hierarchical-master-slave configuration in order to synchronize local clocks within the subnet and to national time standards via wire or radio.

Port Mirroring

A method whereby data on a target port is mirrored to a monitor port for troubleshooting with a logic analyzer or RMON probe. This allows data on the target port to be studied unobstructively.

Port Trunk

Defines a network link aggregation and trunking method which specifies how to create a single high-speed logical link that combines several lower-speed physical links.

179

Remote Authentication Dial-in User Service (RADIUS)

RADIUS is a logon authentication protocol that uses software running on a central server to control access to RADIUS-compliant devices on the network.

Remote Monitoring (RMON)

RMON provides comprehensive network monitoring capabilities. It eliminates the polling required in standard SNMP, and can set alarms on a variety of traffic conditions, including specific error types.

Rapid Spanning Tree Protocol (RSTP)

RSTP reduces the convergence time for network topology changes to about 10% of that required by the older IEEE 802.1D STP standard.

Simple Network Management Protocol (SNMP)

The application protocol in the Internet suite of protocols which offers network management services.

Simple Network Time Protocol (SNTP)

SNTP allows a device to set its internal clock based on periodic updates from a Network Time

Protocol (NTP) server. Updates can be requested from a specific NTP server, or can be received via broadcasts sent by NTP servers.

Spanning Tree Algorithm (STA)

A technology that checks your network for any loops. A loop can often occur in complicated or backup linked network systems. Spanning Tree detects and directs data along the shortest available path, maximizing the performance and efficiency of the network.

Telnet

Defines a remote communication facility for interfacing to a terminal device over TCP/IP.

Transmission Control Protocol/Internet Protocol (TCP/IP)

Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer protocol.

Trivial File Transfer Protocol (TFTP)

A TCP/IP protocol commonly used for software downloads.

User Datagram Protocol (UDP)

UDP provides a datagram mode for packet-switched communications. It uses IP as the underlying transport mechanism to provide access to IP-like services. UDP packets are delivered just like IP packets – connection-less datagrams that may be discarded before reaching their targets. UDP is useful when TCP would be too complex, too slow, or just unnecessary.

Virtual LAN (VLAN)

A Virtual LAN is a collection of network nodes that share the same collision domain regardless of their physical location or connection point in the network. A VLAN serves as a logical workgroup with no physical barriers, and allows users to share information and resources as though located on the same LAN.

Return to CONTENTS

180

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Features 8 PoE+ ports, with total PoE power budget of 58W* and useful PoE power management features
  • Gigabit Ethernet connections on all ports provide full speed of data transferring
  • Integrated security strategy including 802.1Q VLAN, ACL, Port Security and Storm control help protect LAN area investment
  • L2/L3/L4 QoS and IGMP snooping optimize voice and video applications
  • WEB/CLI managed modes, SNMP, RMON bring abundant management features
  • Innovative energy-efficient technology saves up to 50% of power consumption

Related manuals

Download PDF

advertisement