Boss Audio Systems BV9150 User`s manual

User’s Manual
BV9150
MP3-COMPATIBLE DOUBLE-DIN
IN-DASH DVD/MP3/CD AM/FM
RECEIVER WITH 4.5" (114mm)
WIDESCREEN TOUCHSCREEN
TFT MONITOR
WITH USB AND SD MEMORY CARD
PORTS AND FRONT PANEL AUX INPUT
BV9150
MP3-COMPATIBLE DOUBLE-DIN IN-DASH DVD/MP3/CD
AM/FM RECEIVER WITH 4.5" (114mm) WIDESCREEN
TOUCHSCREEN TFT MONITOR
WITH USB AND SD MEMORY CARD PORTS AND
FRONT PANEL AUX INPUT
02.2012
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
iPod® is a trademark of Apple, Inc.
registered in the U.S. and other countries.
tech support: www.bossaudio.com/support
www.bossaudio.com
800.999.1236
Boss Audio Systems is not affiliated with Apple, Inc.
To ensure safety while driving
and to comply with laws,
drivers should not watch video or
operate the video device while driving.
4.5" In-Dash Double-DIN DVD/MP3/CD Receiver
with USB, SD Memory Card
Ports and Front Panel AV Input
1. HANDLING COMPACT DISCS
MOISTURE CONDENSATION
On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit.
Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for
about an hour until the moisture has evaporated.
NOTES ON CDs
Paste or sticky residue.
1. A dirty or defective disc may cause sound
dropouts while playing. To enjoy optimum
sound, handle the disc as follows.
Handle the disc by its edge. To keep the disc
clean, do not touch the surface (P.1).
****
*******
*******
******* *******
P. 5
Do not use CDs with old labels that are
beginning to peel off.
Stickers that are beginning
to peel away leave a
sticky residue (P.6).
P. 6
P. 1
**************
*******
*******
*******
Do not use CDs with labels or stickers
attached.
2. Do not stick paper or tape on the disc (P.2).
Labels are attached (P.7).
*******
*******
*******
*******
*******
P. 2
3. Do not expose the discs to direct sunlight or
heat sources such as hot air-ducts, or leave
them in a car parked in direct sunlight where
there can be a considerable rise in
temperature inside the car (P.3).
P. 7
Do Not Use Special Shape CDs
Be sure to use round shape CDs only. Do
not use any special shape CDs. Use of
special shape CDs may cause the unit to
malfunction.(P.8).
P. 8
P. 3
4. Before playing, clean the discs with an
optional cleaning cloth. Wipe each disc from
the centre out (P.4).
P. 4
5. Do not use solvents such as benzine,
thinner,commercially available cleaners, or
antistatic spray intended for analog discs.
NOTES ON DISCS
If you use the discs explained below, the sticky
residue can cause the CD to stop spinning and
may cause malfunction or ruin your discs.
Do not use CDs that have a sticky residue on the
surface (for example, from peeled-off stickers or
from ink, or glue leaking from under the
stickers).
E-1
CD-Rs and CD-RWs which have not
undergone finalization processing cannot
be played. (For more information on
finalization processing, refer to the manual
for your CD-R/CD-RW writing software or
CD-R/CD-RW recorder.) Additionally,
depending on the recording status, it may
prove impossible to play certain CDs
recorded on CD-R or CD-RW.
2. INSTALLATION
Before finally installing the unit, connect the wiring temporarily and make sure it is all
connected up properly and the unit and system work properly.
Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if
there is a sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum
performance.
30
Avoid installing the unit where it would be subject to high temperature, such as from direct
sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive
vibration.
Be sure to remove the front panel before installing the unit.
SUB-W OUT
BACKSIGHT RCA
ANTENNA JACK
A/V IN (VIDEO IN)
A/V IN (AUDO LEFT)
A/V IN (AUDIO RIGHT)
VIDEO OUT (1 & 2)
REAR LINE OUT LEFT & RIGHT
FRONT LINE OUT LEFT & RIGHT
DIN FRONT/REAR-MOUNT
This unit can be property installed either from Front (conventional DIN Front-mount) or Rear (DIN
Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details,
refer to the following illustrated installation methods A and B.
DIN FRONT-MOUNT (Method A)
Installation the unit
1
1. Dashboard
2. Screw
2
178
100
1
6
7
4
2
5
3
1.
2.
3.
4.
5.
6.
Dashboard
Nut (5mm)
Spring washer
Screw (5x15mm)
Screw
Support Strap
Be sure to use the support strap to secure the
back of the unit in place. The strap can be bent by
hand to the desired angle.
7. Plain washer
Trim Plate Installation:
Push the trim plate against the chassis until it is fitted.
You must do this before you install the front panel, otherwise it can't be attached.
E-2
DIN REAR-MOUNT (METHOD B)
Installation using the screw holes on the sides of the unit.
Fastening the unit to the factory radio mounting bracket.
Note: the mounting box, outer
trim ring,and half-sleeve are not
used for this installation.
Screw
Factory radio
mounting bracket
Note: The mounting box, metal
half sleeve, hook & screws are
not included in the packnig.
Hook
Screw
Hook
Dashboard or console
DETACHABLE CONTROL PANEL (D.C.P.)
Removing The Detachable Control Panel (D.C.P.).
PANEL RELEASE
BUTTON
1. Turn the power off
2. Press the D.C.P. release button
3. Remove the D.C.P.
Attaching the DCP
2
B
A
1. Attach the panel at the right side first, with
point B on the main unit touching point A on
the D.C.P. (As shown on the digram).
2. Then press the left side of D.C.P. onto the
main unit until a click sound is heard.
CAUTION
DO NOT insert the D.C.P from the left side. Doing so may damage it.
The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case
and be careful not to drop it or subject it to strong shocks.
When the release button is pressed and the D.C.P is unlocked, the car's vibrations may
cause it to fall. To prevent damage to the D.C.P, always store it in a protective case after
detaching it.
The rear connector that connects the main unit and the D.C.P is an extremely important
part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Socket
Note:
If the D.C.P is dirty, wipe off the dirt with soft, dry cloth
only. And use a cotton swab soaked in isopropyl
alcohol to clean the socket on the back of the D.C.P.
IMPORTANT
These 2 screws are used to prevent damage to the CD
mechanism during transportation Please make sure to
remove the 2 screws before installing the unit into the
vehicle. DO NOT insert a CD into the unit before
removing the 2 screws.
E-3
3. ELECTRICAL CONNECTION
a. Make sure your car battery is a 12 volt (6 filler caps) negative ground system (if not, a
converter will be necessary).
b. Before starting wiring connections, disconnect the power supply by removing the fuse from
the fuse box.
c. Connect the power wire to one of the extra terminals of the fuse box.
d. Connect the black ground wire to a metal part of the car. It is important to make good
contact.
e. Make other wiring connections as shown.
f. If your car does not have ISO connector, you can purchase it from car accessory shops.
Notes: INCORRECT WIRING OR OPERATION WILL VOID THE WARRANTY OF THIS UNIT.
(CAR UNIT BACK SIDE)
Fuse Replacement:
To replace the fuse, pull out the blown fuse
from the socket. Insert a new one with same
rating
FUSE
RESET BUTTON
The RESET button is located on the main unit (as shown on the diagram). To press it vertically
with a ballpoint pen or metal object to activate it. The reset button should be activated for the
following reasons:
Initial installation of the unit when all wiring is completed.
All the function buttons do not operate.
Error symbol on the display.
Note: If you press the RESET button, and the unit still cannot function normally, please use a
cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.
E-4
4
PANEL
RELEASE
BUTTON
POWER
BUTTON
ENCODER
VOLUME
KNOB
INFRARED
REMOTE
SENSOR
DSP/
LEFT/
RIGHT
BUTTON
MUTE
BUTTON
BAND/
LOUDNESS/
APL/NTSC
BUTTON
MODE
BUTTON
FUNCTION
SELECT
BUTTON
DISPLAY
BUTTON
AMS/
PLAY/PAUSE
BUTTON
LOC
BUTTON
EJECT
BUTTON
TUNING /
SEEK
UP/DOWN
NEXT/BACK
BUTTON
E-5
SCAN
BUTTON
FM MONO /
STEREO
BUTTON
E-6
5. BASIC OPERATION
PANEL RELEASE BUTTON
Press this button to remove the control panel.
POWER BUTTON
Press power button to turn on/off the unit.
DISPLAY BUTTON( DISP )
Press this button briefly, the LCD will display the clock for about 3 seconds,
MUTE BUTTON ( MUTE)
Press MUTE button to mute the sound quickly. the display is flashing Press it again to restore the
previous sound level. When mute is on, the Mute indicator on the LCD will light up.
LOUDNESS BUTTON (LOUD)
Long press this LOUD button control to increase bass output.
MODE BUTTON (MODE)
Press this button to select radio,DISC/USB/SD/MMC/
A/V- IN FRONT /A/V-IN REAR.
FRONT PANEL A/V IN JACK
Left Audio
1
2
Right Audio
Ground
The unit is allowed to connect with external Audio/Video
Video
system such like digital Camera or Game Console, You
can connect the external A/V system thru the A/V in jack
3.5mm A/V Cable ( not included )
on front panel. After connecting the external A/V system,
press mode to A/V IN FRONT to enjoy this external A/V
system on this unit.
NOTE:The unit is only support the 3.5mm A/V Jack Pin Assignment shown as the diagram remove
extra.
SELECT BUTTON (SEL)
press SEL button for less than 1 second to open the Audio menu.
press SEL repeatedly to navigate through the following functions:
VOLUME (VOL) -> BASS (BAS) -> TREBLE (TRE) -> BALANCE (BAL) -> FADER (FAD)
Use Volume Up/Down to adjust desired level within 5 seconds.
NOTE: BASS AND TREBLE WILL BE SKIPPED IF DSP MODE IS ACTIVATED
SUB-WOOFER ON/OFF
Press SELECT button for more than 3 seconds to activate or turn off the Sub-woofer
(Sub-woofer on/off is an optional feature)
ENCODER VOLUME KNOB
Turn this knob to adjust desired volume level.
PRESET EQUALIZER BUTTON (DSP)
Press this PEQ button then use V-UP / V-DN to toggle the following EQ settings.
3
4
POP -> ROCK -> CLASSIC -> DSP OFF
At DSP off mode preset equalizer will be controlled by Bass / Treble setting.
E-7
6. SYSTEM SETUP
Basic operation of menu setup
1. General setup menu
In main menu,touch "
"to enter into"SETTINGS"mode.
2.Choose menu setup
* Touch cursor and choose setup menu.
3.Enter or exit menu
* Touch
in the menu and enter into"SETTINGS"menu.
* Touch
in the SETTINGS menu to exit current setup menu.
4.Menu setup operation
TIME SETUP: The unit utilizes a 24 hr time format, touch
on the touch screen directly to
adjust hour and minute.
BEEP/ON OFF: To determine how the beep sound is generated when the keys are pressed.
CALIBRATION : Touch + center with a pen point, and t ouch it again to enter into the calibration menu
and display.
+
+
+
+
+
+
Users can operate"touch rectiflcation"if the touch character deviates.
Users must Touch+
in the center rectification or else it will affect precision.
DUAL FREQUENCY SELECTION
Unit is defaulted in U.S.A(America) frequency, if EURO frequency is required, touch the
Icon
at the main menu to go to settings menu.And then touch and tick “EUROPE” to change to EURO
frequency.
E-8
7. RADIO OPERATION
RADIO FUNCTION KEY
Touch the
icon in any mode to go back to the main menu and select"RADIO"to enter the
radio mode.
15
FM1
CH-00
87.50M
1
87.50MHZ
90.10MHZ
98.10MHZ
106.10MHZ
107.90MHZ
87.50MHZ
12:06
AM
2
3
16
16
4 9 5 10 6 11 7
Serial number
Name
12
13
8 14
17
Function description
1
Information
2
CLOCK
3
4
5
6
7
8
9
Radio
10
LOUD
LOUDNESS ON/OFF
11
EQ
ROCK\POP\CLASS\EQ.OFF
12
MONO
ST:ON \OFF
13
LOC
LOCAL/DX
14
SCAN
CURRENT TIME
TOUCH TO SELECT RADIO AND PRESS LONGER TO STORE CURRENT FREQUENCY
MUTE
CLOSE\OPEN AUDIO OUTPUT
SEL
VOL-BASS-TRE-BAL-FAD
BND
BAND SWITCH(FM1\FM2\FM3\AM1 AM2 )
TFT OFF
TFT DISPLAY ON/ OFF
/
FREQUENCY BACKWARD/FREQUENCY FORWARD
AUTO SCAN AND STORE RADIO
15
SEARCH STATIONS
BACK TO MAIN MENU
16
17
CURRENT BAND AND FREQUENCY
ADJUST DESIRED VOLUME LEVEL
P1/2- P2/2
ANOTHER FANCTION KEY
E-9
FM MONO / STEREO BUTTON (MONO)
Use this control to select stereo or mono reception for FM radio stations. You can sometimes
improve reception of distant stations by selecting mono mode.
LOCAL / DX BUTTON (LOC)
This control can be used to change between Local and Distant (-DX) tuning mode. Local
mode improves reception in some areas where the signal is too strong.
STATION PRESET BUTTONS (M1-M6)
You can store & recall six preset radio stations by pressing M1-M6 buttons
TO STORE A STATION: 1) select a band (if needed)
2) select a station by tuning up / down button
3) hold a preset button which you want store the station for at least 2
seconds. The preset number will appear on the display
accompanied by a beeps sound.
TO RECALL A STATION: 1) select a band (if needed)
2) press a preset button briefly to recall the stored station.
SCAN BUTTON (SCAN)
Press this button, the radio will tune up to search stations, the available stations will blinking and
stay on the display for a few seconds.
AUTO MEMORY STORE / PRESET SCAN BUTTON (AMS)
PRESET SCAN: press AMS button for less than 1 second to scan all preset stations in the
memories of the current band and stay on each memory stations for about 5
seconds. The memory location indicator on the LCD will flash during the process.
To stop preset scan, press AMS button again.
AUTO MEMORY STORE: press AMS button for more than 1 second to enter auto store mode. The
radio will automatically store 6 stations to the 6 preset memories of the current band. To stop auto
store, press AMS button again.
BAND BUTTON (BAND)
Press this button to change between band FM1, FM2, FM3 or MW(AM)1, MW(AM)2 bands .
TUNING UP / DOWN BUTTON (
)
1.Press these buttons briefly will operate MANUAL SEARCH tuning mode, the radio will tune up
or down to the next station and remain on the frequency.
2.Press these buttons more than 2 seconds, operate as AUTO SEARCH buttons, under this mode
the tuning frequency will advance up or down rapidly when the button is pressed. If the buttons
are not pressed within 3 seconds, they will return to auto search mode.
E - 10
8. DISC/MULTI-MEDIA FILES OPERATIONS
2
The playing file is a Music file.
The playing file is a Photo file.
File Switch Region: Displays the file
type of the playing and the switching.
Function KEY
KEY
AUDIO
OK
OSD
MENU
TITLE
+
NUM
10
12
11
S.N
NAME FUNCTION
Menu
Information
13
DESCRIPTION
CURRENT DIRECTORY NAME
DISPLAY DISC INFO RMATION
BACK TO MAIN MENU
MOVE CURSOR DIRECTION
CONFIRM SELECTED INFORMATION
PAUSE/PLAY
REPEAT. REPI
DIR
ALL
PREVIOUS MUSIC/ NEXT MUSIC
BACKWARD/ FORWARD
STOP BUTTON
OSD
NUM
THIRD TIME TO MAKE THE OSD DISAPPEAR.
NUMBER
ANOTHER FANCTION KEY
E - 11
MULTI-MEDIA FILE OR FOLDER SEARCHING
CD SLOT
Insert the disc into CD slot. The CD will begin to play.
EJECT BUTTON
Press this button to eject the CD from the unit. The receiver will switches to radio mode
automatically.
PLAY/PAUSE BUTTON (
)
Press this button briefly to pause disc play, press again to resume play.
NEXT/BACK BUTTONS(
&
)
When NEXT is pressed, the unit will go to the next track and start the playback.
When BACK is pressed, the unit will go back to the preivous track and start the playback.
Long press the
&
buttons under the play mode, the unit will start to forward or rewind. you
can play discs at various speeds. with each consecutive long press the
&
buttons , the
playback speed increases. there are 5 speed levels for discs in FWD/REV: X2, X4, X8,X16, X20.
there are 4 speed levels for disc types other than disc: X2, X4, X8,X16,X20.
Press PLAY to resume the playback at normal speed.
Selecting a Track to Play
1. Use the UP/DOWN/LEFT/RIGHT direction buttons to move to different file/folder
Numbers.
2. Press OK on a file number, and that file will begin to play, or by direct numeric input,
3. Enter a file number with the numeric buttons (0-9) and +10 button to play the input Files
Number.
REPEAT A-B BUTTON (A-B)
1. Press REPEAT A-B at your chosen starting point.
2. Press REPEAT A-B again at your chosen end point.
The section A and B can be set only within the same track.
The section will now repeat continuously.
3. To exit the sequence, press REPEAT A-B.
The screen will display the following message:
REPEAT A-
REPEAT A- B
REPEAT A-B CANCEL
NOTE:This operate is with CD function only.
STOP BUTTON(
)
Stop the current disc playback.
Briefly press the STOP button to stop the unit playback, when the PLAY button is pressed, normal playback will
continue.
Press STOP two times consecutively to enter the clear stop mode. Under the clear stop mode, if PLAY is
pressed, the disc will resume the playback from the beginning of the disc.
NUMERIC BUTTONS
When playback CD/Music file use for track number or File number direct access and
Use when function need numeric Selection or Input, like in the Goto function, etc.
UP/DOWN/LEFT/RIGHT BUTTON (
/
Use to move cursor up/down/left/right.
/
/
OK BUTTON
Use this button to confirm the selection.
E - 12
)
GO TO BUTTON (GO TO)
Using GO TO feature to select track number or specific time.
A. Press GO TO button,the screen will display the following message:
A
TRK 001/021
00:01: 56
B. Press Arrow Left/Right buttons to highlight the track number or the time option.
C. Use numeric buttons to enter the track you want to play or the elapsed time you
wantto go to in that track.
D. Press OK button to start playback.For example entering 00:01:56 will start playback
one minutes and fifty-six seconds into the title.
PROGRAM BUTTON (PROG)
Press PROG button the screen will display the following message.
PROG
1
2
3
4
0002
0004
-------
5 ---6 ---7 ---8 ---PLAY
9
10
11
12
------------CLEAR
13
14
15
16
-------------
A. For example:Press numeric button 2 ,PROGRAM 0002 appears it means track 2 will
be player first then press numeric button 4 and PROGRAM 0004 appears,press the
different numeric button to select the corresponding track and then you can program
tracks to your need if you want to complete program setting press PLAY button to play
tracks in programmed order.
B.Press the ( / /
/ )buttons to highlight select program mode or track number
and press PLAY button to confirm it.
C.If you exit program mode and program off appears press STOP button then press
PLAY button.
ID3 INFORMATION DISPLAY
If any Music file contains any ID3-TAG information, user can view these ID3-TAG information such
as Track title, Artist title, Album title, etc, These ID3-TAG information will be displayed on the lower
left hand corner of the TFT monitor.
E - 13
9. PLAY MULTI-MEDIA FILES OPERATION
Place a disc into the player, and the player will automatically search the directories saved files.
After searching, it will auto go to the first directory saved files (to the disc containing both Music and
Photo files; To the disc containing single type of files, it will automatically go to the first directory)
and play the first song in the directory (“01:” is highlighted).The screen displays as the picture
below:
Current directory name
Current file name.
The playing file is a Music file.
The playing file is a Photo file.
File Switch Region: Displays the file
type of the playing and the switching.
Function KEY
KEY
Use the Arrow ( /
/ /
)buttons to enter the Directory Region and highlight the desired
directory, then the first track under it starts playback; Also you can use the Arrow( /
/
/
)
buttons to enter the File Region and select the file you want to play.
NOTE:
Press the Left and Right arrow buttons, you can activate Directory Region, File Region and File
Switch Region separately.
The highlight in Directory Region and File Region is shown as the picture above;
While it appears a transparent rectangle in File Switch Region.
You can press the Numeric buttons to select the file you want to play. For example, if
you desire the 15th track in current list, press the “10+” button once, then press “5”,
the 15th starts playback.
NOTE: When a picture is playing or paused, press the Arrow buttons to change the display
angle:
E - 14
10. MMC/SD CARD & USB DEVICE OPERATIONS
START THE USB DEVICE MODE
USB SOCKET
P.1
1.The USB mini socket is accessible as indicated in
picture 1.(P.1)
2.Plug in the USB drive / device completely as indicated
in picture 2(P.2) and display will show “USB” to indicate
that the USB drive / device is being plugged in correctly
& the download has begun.
3.Does not matter what mode the unit is in, once a USB
drive / device is being plugged into the unit, unit will
automatically switch to USB mode.
P.2
4.All the USB files playback function is same as normal disc
playback.
Warning: Excessive weight or size USB drive/device may
cause permanent & serious damage to the unit and may
cause access to the buttons on the front panel impossible.
User must use an extension cable (provide by USB device
manufacturer) to connect with USB socket to prevent any
damage cause.
TO STOP USB PLAYBACK
1.If the USB drive / device is unplugged, the unit will automatically switch to radio mode.
Or user can use mode button to switch to other modes.
2.The user can use the mode button to choose USB mode (only if USB drive / device is
inserted in the unit ) or any other modes, when they are in any mode.
USB SPECIFICATION
* SUPPORT MAX IG USB FLASH MEMORY
P.3
* SUPPORT MAX 999 SONGS
* USB 1.1 DEVICE SUPPORT
* USB 2.0 DEVICE SUPPORT
(TRANSFER SPEED SAME AS VER 1.1)
* FILE MANAGER: FAT12/FAT16/FAT32
CAUTION
1.Always unplugg the USB gently from the unit,
excessive force used will cause permanent & serious
damage to the unit & the USB drive / device.
COMPATIBILITY
Due to the fast changing technology world, this unit may
or may not be compatible to all the USB drive / device
available with all the future technology, especially those
USB drive / device which require to install a driver.
Always choose a compatible USB drive / device which is
compatible with this unit.
E - 15
START THE SD/MMC MODE
P.4
D.C.P.
P.6
1.Press panel release button to release the front panel.(P.4)
2.The SD/MMC card slot is located on top of the front panel as
indicated in (P.5).
3. Insert the SD/MMC card into the card slot in the correct direction
until a “CLICK” sound is heard.
4.Close the front panel.
5. The display will show “CARD” to indicate that the SD or
MMC card is correctly inserted. Once the SD or MMC card is
inserted, the file will automatically loaded & playback will also
start.
6. Does not matter what mode the unit is in, once a SD or MMC
card is being inserted in the unit, unit will automatically switch to
SD / MMC mode.
7. All the SD / MMC files playback function is same as normal CD or
Multi-Media disc playback.
TO STOP SD/MMC CARD PLAYBACK
1.Push on the end of the SD or MMC card to eject the SD or MMC card. Once the SD or MMC
card is taken out, the unit will automatically switch to previous mode.
2.User can use the mode button to choose SD / MMC mode (only if SD or MMC is inserted in
the unit ) or any other modes, when they are in any mode.
SD/MMC SPECIFICATION
* SUPPORT MAX 4G SD/MMC CARD
* SUPPORT MAX 999 SONGS
CAUTION
2.Please make sure to insert the SD or MMC
card in the correct direction / orientation as
indicated in picture 7(P.7). Wrong insert will
cause permanent & serious damage to the
unit & the SD or MMC card.
P.7
Front side
E - 16
Back side
11. VIDEO DISC OPERATIONS
DVD TT 01/05 CH 011/018
AUDIO
OK
OSD
MENU
15
S.N
01:11:56
NUM
TITLE
2
16
Name Function
Information bar
17
+
19
18
14
1
Description
DISPLAY DISC INFO.
ANGLE
BACK TO MAIN MENU
MOVE CURSOR UP/DOWN/LEFT/RIGHT
CONFIRM SELECTED INFORMATION
PAUSE/PLAY
BACK TO MAIN MENU OF DISC
PREVIOUS MUSIC/ NEXT MUSIC
BACKWARD/ FORWARD
ENTER INTO SETUP MENU OF AUDIO AND VIDEO
STOP BUTTON
OSD
DISPLAY THE AMOUNT OF TIME PLAYED
NUM
NUMBER
ANOTHER FANCTION KEY
14
15
AUDIO
16
17
TITLE
18
19
SELECT LEFT AND RIGHT CHANNEL
REPEAT CHAPTER/TITLE/ALL
TITLE MENU
SUBTITLE
+
ZOOM
E - 17
10 11
13
12
14
10
11
12
13
14
HUE - / HUE +
USER/STDY /BRIG/ SOFT /SHAR
PLAY BUTTON (
)
Press this button briefly to pause disc play, press again to resume play.
STOP BUTTON(
)
Stop the current disc playback.
Briefly press the STOP button to stop the unit playback,when the PLAY button is pressed,normal
playback will continue.
Press STOP two times consecutively to enter the clear stop mode. Under the clear stop mode, if
PLAY is pressed, the disc will resume the playback from the beginning of the disc.
UP/DOWN/LEFT/RIGHT BUTTON (
/
Use to move cursor up/down/left/right.
OK BUTTON
Use this button to confirm the selection.
/
/
)
NEXT/BACK BUTTONS(
&
)
When NEXT is pressed, the unit will go to the next track and start the playback.
When BACK is pressed, the unit will go back to the preivous track and start the playback.
Long press the
&
buttons under the play mode, the unit will start to forward or rewind.
you can play discs at various speeds. with each consecutive long press the of
&
buttons , the playback speed increases. there are 5 speed levels for discs in FWD/REV: X2,
X4, X8, X16,X20. there are 4 speed levels for disc types other than disc: X2, X4, X8,X16,X20.
Press PLAY to resume the playback at normal speed.
E - 18
NUMERIC BUTTONS
Use when playback disc which need numeric Selection or Input, like in the Goto
function, etc.
PAL/NTSC BUTTON (P/N)
In order to achieve the best image display effect, you must adjust the player signal system to
match your TV set.
3 types of TV color signal system are available: NTSC, PAL60 or Automatic mode.
Use P/N button to select between NTSC/PAL, or automatic mode.
REPEAT A-B BUTTON (A-B)
1. Press REPEAT A-B at your chosen starting point.
2. Press REPEAT A-B again at your chosen end point.
The section A and B can be set only within the same track/chapter.
The section will now repeat continuously.
3. To exit the sequence, press REPEAT A-B.
The screen will display the following message:
REPEAT A-
REPEAT A-B
REPEAT A-B CANCEL
L/R BUTTON(L/R)
Press R/L button for select left and right channel.
The screen will display the following message:
STEREO
MONO L
MONO R
ZOOM BUTTON(ZOOM)
The ZOOM feature allows you to magnify a certain area of the images recorded on the Video
disc and other image discs. the screen will display the following message:
ZOOM X2
ZOOM X3
ZOOM X4
ZOON ½
ZOON 1/3
ZOON 1/4
ZOOM OFF
A. Press ZOOM button once to enlarge the image by X2.
B. Press ZOOM button twice to enlarge the image by X3.
C. Press ZOOM button three to enlarge the image by X4
D. Press ZOOM button four to enlarge the image by½.
E. Press ZOOM button five to enlarge the image by 1/3.
F. Press ZOOM button six to enlarge the image by 1/4
G. Press UP/Down/Left/Right to select the area you want to magnify.
H. The four times press of ZOOM will cancel the zoom function and resume normal playback.
SLOW BUTTON (SLOW)
A. Press “SLOW” button once to activate SLOW 1/2 slow motion playback.
B. Press “SLOW” button twice to activate SLOW 1/3 slow motion playback.
C. Press “SLOW” button three times to activate SLOW 1/4 slow motion playback.
D. Press “SLOW” button four times to activate SLOW 1/5 slow motion playback.
E. Press “SLOW” button five times to activate SLOW 1/6 slow motion playback.
F. Press “SLOW” button six times to activate SLOW 1/7 slow motion playback.
G. Press “SLOW” button again to restore normal playback.
The screen will display the following message:
SF1/2
SF1/3
SF1/4
SF1/5
SF1/6
E - 19
SF1/7
PLAY
PBC FUNCTION BUTTON (PBC)
Press the “PBC” button to turn on PBC function. The unit will show the song list on the
screen of the monitor after the WARNING from the Video CD. Then you can choose the
song by pressing the desired number key.
Press PBC key return to manual of Video CD,
NOTE:This only operates with the PBC function on VCD.
GO TO BUTTON (GO TO)
Using GO TO feature to select track number or specific time:
TT 01/05 CH 011/018
01:11:56
A. Press GO TO button,the screen will display the following message:
B. Press Arrow Left/Right buttons to highlight the track/title/chapter number or the time
Option.
C. Use numeric buttons to enter the track/title/chapter you want to play or the elapsed time
you wantto go to in that track/title/chapter.
D. Press OK button to start playback.For example entering 01:11:56 will start playback one
hour,eleven minutes and fifty-six seconds into the title.
PROGRAM BUTTON (PROG)
The PROGRAM feature, select TITLE/CHAPTER to edit.
A. Use numeric buttons to enter highlight PROGRAM title/chapter,for example:press numeric
button title 2,chapter 4,PROGRAM T02/C04 appears it means Title 2,chapter 4 will be
played first then press numeric button title 3,chapter 5 and PROGRAM T03/C05 appears,
press the different numeric button to select the corresponding title/chapter and then you
can program title/chapter to your need.if you want to complete program setting press PLAY
button to play chapters in programmed order.
See the illustration below:
PROG
1
2
3
4
T C
02:04
03:05
--:---:--
T C
5 --:-6 --:-7 --:-8 --:-PLAY
T C
9 --:-10 --:-11 --:-12 --:-CLEAR
13
14
15
16
TC
--:---:---:---:--
B. Press the (
/
/
/
)buttons to highlight select program mode or title/chapter and
press PLAY button to confirm it.
C. If you exit program mode and program off appears press STOP button then
press PLAY button.
TITLE BUTTON (TITLE)
1. Press TITLE to invoke Title Menu (Dependent on authoring of disc).
2. Press direction(
/ / /
) buttons to highlight selected Title Menu entry.
3. Press OK or PLAY to select the highlighted entry. If the highlighted entry
indicates a title, that title will play from Chapter 1.
NOTE:This only operate if the disc with the TITLE function.
DISC MENU
1. Press DISC MENU to invoke the menu screen included on the disc.
2. Press direction buttons to highlight a selected menu entry.
3. Press OK or PLAY to select the highlighted entry. If the highlighted entry indicates a
chapter or title, the disc will play from the selected spot.
E - 20
SUBTITLE BUTTON (SUBTITLE)
1. Press SUBTITLE button to bring up the subtitle information which will be shown on the top right
corner of the screen.
2. Each time you press SUBTITLE, you can switch to another subtitle available in the disc.
NOTE:This only operate if the disc with the SUB TITLE function.
ANGLE BUTTON (ANGLE)
Press ANGLE button to bring up the angle information which will be shown on the top right
corner of the screen.
Each time you press ANGLE, you can switch to another camera angle available in the disc.
NOTE:This only operate if the disc with the ANGLE function.
OSD BUTTON
1. Press OSD button to display the amount of time played and time remaining to be
played on the disc.
2.
Press OSD button once to additionally display the disc type, current chapter or track,
and total number of chapters or tracks.
Also displayed is the current title, total number of titles.
Press OSD button a second time to additionally display the disc type,Audio
language/type/# of channels, subtitle language, and angle selection.
3.
Press OSD button a third time to make the OSD disappear.
E - 21
12. SET UP MENU OPERATION
General Steps of Setup Menu
1) Press the Setup button, the main setup menu appears.
When the main menu displayed, the Video will auto pause.
2) Press the Left and Right arrow buttons to highlight the icon of the desired page, then press the
Down or Right arrow button to activate that page; For example, if you want to setup the video
page, press Right to highlight the video icon, the video page will be displayed on the screen.
3) Press the Down arrow button to highlight the desired option. Press ok or press Right to select,
the choices of that option appear on the right; For example, press the Down arrow button to
highlight the BRIGHTNESS option, then press ok to select, the brightness choices appear on
the right.
E - 22
4) Press the Arrow buttons to highlight the Exit Setup option, then press Enter or Setup
again to exit Setup Menu.
NOTE: When setup, the pressing setup buttons will turn off the setup menu, while the
choices that have been changed will be saved.
Setup Items Introduction
1) SYSTEM SETUP
The system setup options are illustrated below:
TV SYSTEM
According to the Color System of the TV, you can choose the TV System.
1. NTSC: Choose this settings if your Multi-Media player is connected to a NTSC TV.
2. PAL: Choose this settings if your Multi-Media player is connected to a PAL TV.
3. AUTO: Choose this settings if your Multi-Media player is connected to a multi-system TV.
The default setting is NTSC.
SCREEN SAVER
If the screen saver is on, when your disc player is in Stop, Open, or No Disc state, or there is a
frame frozen for more than 30 minute, the screen saver will be displayed. This feature can protect
the screen from damage.
ON: Choose this setting to activate the screen saver.
OFF: Choose this setting to cancel the screen saver
The default setting is ON.
E - 23
TV TYPE
16 : 9 (Wide Screen): Choose this setting if your Multi-Media player is connected to a wide
screen TV. If you choose this setting and you don't have a wide screen TV, the images on the
screen may appear distorted due to vertical compression.
4 : 3 LB (Letter Box): Choosing this setting if your Multi-Media player is connected to a normal
ratio TV. connector You'll see the movies in their original aspect ratio (height-to-width ratio).
You'll see the entire frame of the movie, but it will take up a smaller portion of the screen vertically.
The movie might appear with black bars at the top and bottom of the screen.
4 : 3 PS (Pan & Scan): Choosing this setting if your Multi-Media player is connected to a normal
ratio TV. You can fill the movie to the entire screen of your TV. This might mean that parts of the
picture (the left and right edges) won't be seen.
NOTE:
The image display ratio is related to the recorded disc format. Some disc can not display
images in the aspect ratio you choose.
If you play a disc recorded in 4:3 format on a wide screen TV, black bars will appear on
the left and right side of the screen.
You must adjust the screen setting depending on the type of the television you have.
PASSWORD
The password option is initialized locked, and you cannot set the ratings limit or change the
password. In order for the Ratings feature work, the password mode must be turned on. If you want
to set the ratings limit, you will need to enter the default password, which is 0000, then press ok to
confirm. To change the password, you will be prompted for the old password, then be prompted
for a new. Enter a 4-digit number (this is your password).
RATING
The Rating feature is a rating limit system, like movie ratings. It works with discs that have been
assigned a rating. This helps you control the types of Discs that your family watches.
There are eight rating options: 1. KID SAFE, 2. G, 3. PG, 4. PG-13, 5. PG-Q, 6. R, 7. NC17, 8.ADULT.
Select the ADULT option to cancel the rating limit.
The default setting is ADULT.
NOTE: If the password option is locked, you cannot set the ratings limit; the rating limit does
not work when the password option unlocked.
DEFAULT
Choose this option to resume all the setup options to default settings.
2).LANGUAGE SETUP
The language setup options are illustrated below:
SPAINISH
FRENGH
PORTUGUCSE
ITALIAN
RUSSIAN
DUTCH
E - 24
OSD LANGUAGE
Highlight the OSD LANGUAGE option, and press the Arrow buttons to choose the OSD
language you prefer. Press Enter to confirm, and it will display OSD in that language.
AUDIO LANG
Highlight the AUDIO LANG option, and press the Arrow buttons to choose the audio language
you prefer. Press Enter to confirm. If the disc you are playing has that language available, it will
output audio in that language.
SUBTITLE LANG
Highlight the SUBTITLE LANG option, and press the Arrow buttons to choose the subtitle
language you prefer. Press ok to confirm. If the disc you are playing has that language available,
it will displays subtitles in that language.
MENU LANG
Highlight the MENU LANG option, and press the Arrow buttons to choose the menu language
you prefer. Press ok to confirm. If the disc you are playing has that language available, it will
displays menu in that language.
NOTE: If your preferred language isn't available, the disc's default language will be played.
The default language of your Multi-Media player is English.
3).VIDEO SETUP
The video setup options are illustrated below:
SHARPNESS
BRIGHTNESS
Use the Up and Down arrow button to move the scroll and adjust the brightness.
CONTRAST
Use the Up and Down arrow button to move the scroll and adjust the contrast.
HUE
Use the Up and Down arrow button to move the scroll and adjust the hue.
SATURATION
Use the Up and Down arrow button to move the scroll and adjust the saturation.
SHARPNESS
Use the Up and Down arrow button to move the scroll and adjust the sharpness.
E - 25
13. SPECIFICATIONS
CD PLAYER
System
Usable disc
Sampling frequency
No of quantization bits
Frequency
Number of channels
S/N Ration
Compact disc audio system
Compact disc, CD-R, CD-RW
44.1KHz
1bit
5-20,000Hz
2 stereo
70dB
RADIO SECTION
FM
Frequency Range
Intermediate Frequency
Usable Sensitivity
Stereo Separation
S/N Ratio
87.5 -108 MHz (EURO)
87.5 -107.9 MHz (USA)
10.7 MHz
Better than 15dB at S/N 30 dB
25 dB at 1KHz
50 dB
AM (MW)
Frequency Range
Intermediate Frequency
Usable Sensitivity
S/N Ratio
522 -1620 KHz (EURO)
530 -1710 KHz (USA)
450KHz
Better than 45dB
40 dB
GENERAL
Power Supply
Polarity
Speaker impedance
Power Output
DC 11 -14V
Negative Ground
4 ohms
80W x 4
REMARK :
Specifications subject to change without notice.
E - 26