TD-6KW_e 1 ページ 2006年1月24日 火曜日 午後6時3分
TD-6KW
Owner’s Manual
Thank you, and congratulations on your choice of the Roland Drum System TD-6KW.
201a
Before using this unit, carefully read the sections entitled: “USING THE UNIT
SAFELY” and “IMPORTANT NOTES” (p. 2, p. 3). These sections provide important
information concerning the proper operation of the unit. Additionally, in order to feel
assured that you have gained a good grasp of every feature provided by your new
unit, Owner’s manual should be read in its entirety. The manual should be saved
and kept on hand as a convenient reference.
* For the Snare (PDX-8) to function correctly, trigger parameters
in the sound module TD-6V must be adjusted.
202
Copyright © 2006 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the
written permission of ROLAND CORPORATION.
TD-6KW_e 2 ページ 2006年1月24日 火曜日 午後6時3分
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers
other adverse effects
respect to the home
furnishings, as well
animals or pets.
to damage or
caused with
and all its
to domestic
001
•
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
006
Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
•
................................................................................................
002b
•
Do not open or perform any internal modifications
on the unit. (The only exception would be where
this manual provides specific instructions which
should be followed in order to put in place user-installable
options; see p. 7.)
................................................................................................
................................................................................................
011
•
003
•
Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
................................................................................................
•
................................................................................................
In households with small children, an adult should
provide supervision until the child is capable of
following all the rules essential for the safe
operation of the unit.
Never use or store the unit in places that are:
................................................................................................
• Subject to temperature extremes (e.g.,
direct sunlight in an enclosed vehicle, near
a heating duct, on top of heat-generating
equipment); or are
014
• Damp (e.g., baths, washrooms, on wet
floors); or are
•
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
................................................................................................
005
This unit should be used only with a rack or stand
that is recommended by Roland.
................................................................................................
Do not drop it!
104
•
• Humid; or are
•
Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
013
004
•
When using the unit with a rack or stand recommended by Roland, the rack or stand must be
carefully placed so it is level and sure to remain
stable. If not using a rack or stand, you still need to
make sure that any location you choose for placing
the unit provides a level surface that will properly
support the unit, and keep it from wobbling.
Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
................................................................................................
106
•
Never climb on top of, nor place heavy objects on
the unit.
................................................................................................
118a
•
Should you remove nuts, washers, screws, anchor
bolts, etc., keep them in a safe place out of
children’s reach, so there is no chance of them
being swallowed accidentally.
................................................................................................
2
TD-6KW_e 3 ページ 2006年1月24日 火曜日 午後6時3分
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT
SAFELY” on page 2, please read and observe the
following:
Placement
354a
•
Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
Excessive heat can deform or discolor the unit.
356
•
Do not allow rubber, vinyl, or similar materials to remain
on the unit for long periods of time. Such objects can
discolor or otherwise harmfully affect the finish.
Maintenance
401a
•
For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
402
•
Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
Additional Precautions
553
•
Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
556
•
When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
558a
•
To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
558d
•
This instrument is designed to minimize the extraneous
sounds produced when it’s played. However, since sound
vibrations can be transmitted through floors and walls to a
greater degree than expected, take care not to allow these
sounds to become a nuisance to neighbors, especially
when performing at night and when using headphones.
562
3
TD-6KW_e 4 ページ 2006年1月24日 火曜日 午後6時3分
Checking the Contents of the
Box
Drum Stand
Assemble the Drum Stand.
❑ TD-6V (Percussion Sound Module) x 1
❑ KD-8 (Kick Trigger Pad) x 1
About the Stand, refer to the owner’s manual for the
❑ FD-8 (Hi-Hat Control Pedal) x 1
stand.
❑ PDX-8 (V-Pad) x 1
❑ PD-8 (Pad) x 3
❑ CY-5 (Cymbal Pad) x 1
❑ CY-8 (Cymbal Pad) x 2
❑ Connection Cables
❑ Tuning Key x 1
■ TD-6KW Owner’s Manual x 1
• The tuning key is included in the FD-8 package.
• The TD-6V Owner’s Manual is included in the TD-6V
package.
• This package does not include a kick pedal. Use with a
commercially available kick pedal.
• This package does not include the CY-5 attachment set
for cymbal.
962a
* In the interest of product improvement, the specifications and/
or appearance of this unit are subject to change without prior
notice.
TD-6V
(Percussion Sound Module)
Attach the mounting plate (included with the optional drum stand) to the TD-6V.
Using the screws attached to the bottom panel, attach the holder so the unit is oriented as shown in the diagram.
fig.TD-6V.e
• To attach the stand holder, remove the four 8 mm
screws (M5 x 8) from the bottom of the TD-6V and
use them. Use of other screws may result in
damage to the unit.
928
• When turning the unit upside-down, get a bunch
of newspapers or magazines, and place them
under the four corners or at both ends to prevent
damage to the buttons and controls. Also, you
should try to orient the unit so no buttons or
controls get damaged.
Narrow
929
• When turning the unit upside-down, handle with
care to avoid dropping it, or allowing it to fall or
tip over.
4
Wide
TD-6KW_e 5 ページ 2006年1月24日 火曜日 午後6時3分
USING THE UNIT SAFELY
PDX-8
Adjusting the Head Tension
(Snare)
fig.PD-85.e_80
Hoop
Tuning Bolt
Rim Rubber
Head Sensor
Before using the pad, tighten the
head so that the tension is rather firm.
Looseness in the head tension may result in problems such as
failure of the PDX-8’s rim shots to sound or double triggering.
Head
Stand Fixing Screw
Output Jack
Striking the head when the head tension is loose may
damage the sensor.
Shell
1. Use the tuning key to tighten the tuning bolts.
Strike the head to check the feel and response.
fig.Adjust.e
Holder
Loosen
Rim Sensor
Tighten
add
* Do NOT place your fingers inside the shell, as you may hurt
yourself or cause damage to the PDX-8. Or when changing the
head, do NOT touch any of the internal parts. Also, do not
insert your fingers into the hole of the mounting bracket.
fig.Stand.j
Tighten each tuning bolt one by one, observing the
numerical order shown in the diagram. Do not firmly
tighten a single tuning bolt by itself. Doing so will make
it impossible to tension the head evenly, and will cause
malfunctions.
fig.Bolt
3
1
5
fig.Stand.j
Head Sensor
Rim Sensor
2
6
4
2. Fine-tune the adjustment while continuing to
check the pad feel and response.
• On the PDX-8, adjusting the head tension affects only the
head response, and does not change the pitch of the
sound as it would on an acoustic drum.
Head Sensor
• Head tension may slacken with the passage of time.
Readjust the tension as needed.
5
TD-6KW_e 6 ページ 2006年1月24日 火曜日 午後6時3分
USING THE UNIT SAFELY
fig.RimShot.e
Attaching the Pad to a Stand
Attach the PDX-8 to a pad mount of the stand.
Be sure to tighten the stand fixing screw securel. If it
remain loose, double triggering may occur.
fig.Stand.e
Suitable position
for rim shots
Tighten
Player
Loosen
Cross Stick
Only strike the rim of the pad.
Depending on the instrument assigned to the rim, you
can play rim shots and/or cross stick sounds.
Rod
fig.XStick.e
Playing Methods
Head Shots
Rim
Rim
fig.HeadShot.e
* To play the cross stick, be sure that you only strike the rim of
the pad. Placing your hand on the head of the pad might
prevent the cross stick sound from being played properly.
For more on settings and tones, see the respective
module’s owner’s manual.
Head
* Do not strike the hoop.
If you hear a rim sound when you strike the head,
decrease the “Rim Sens” value.
If you cannot get a rim sound even when you strike
the rim hard, increase the “Rim Sens” value.
Rim Shots
fig.RimShot.e
Rim
* To play rim shots, strike the rim in the area shown in the
diagram.
6
TD-6KW_e 7 ページ 2006年1月24日 火曜日 午後6時3分
USING THE UNIT SAFELY
Head Replacement
Specifications
PDX-8
When the Head Should Be Replaced
Head Size:
8 inches
The head is an expendable item that eventually will wear out
and need to be replaced. Replace the head when the following
occurs:
Triggers:
2 (Head, Rim)
Dimensions:
266 (W) x 326 (D) x 62 (H) mm
Slack portions remain in the head even when the head tension
is properly adjusted.
Weight:
1.3 kg
Replacement heads (optional): MH-8 Mesh Head
Option:
10-1/2 (W) x 12-7/8 (D) x 2-1/2 (H) inches
2 lbs 14 oz
Mesh Head (MH-8)
1. Remove all tuning bolts from the PDX-8.
* The Rim rubber is one component that eventually wears out
(the more so if numerous rim shots are performed), and will
require replacement. Rim shots may not be performed correctly
when the rim rubber is worn out. If this occurs, replace the rim
rubber. Consult Roland Service for more on replacing the rim
rubber.
fig.Replace.e
Loosen
Tighten
Tuning Key
Tuning Bolt
add
* Due to the nature of the materials used in the sensor, changes
in room temperature may affect the sensitivity of the sensor.
Hoop
Head
Sensor
Hoop’s Rubber
Portion
Shell
Do not apply excessive force to the sensor located under
the head. Doing so can interfere with accurate detection,
and may damage it.
2. Remove the hoop.
3. Remove the old head.
4. Place the new head on the shell.
5. Place the hoop onto the head.
6. Attach the tuning bolts to the hoop and shell.
7. Next, adjust the tension of the head. Refer to
“Adjusting the Head Tension” (p. 5).
Do not firmly tighten a single tuning bolt by itself. Doing
so will make it impossible to tension the head evenly, and
will cause malfunctions.
7
TD-6KW_e 8 ページ 2006年1月24日 火曜日 午後6時3分
USING THE UNIT SAFELY
PD-8
Playing the PD-8
(Tom)
fig.PD-HR.e
fig.PD-8.e
Head Shot
Stand Fixing Screw
Head
Rim Shot
Head
Head
Rim
To play the sound assigned to the head, hit only the head.
Stand Fixing Screw
To play a rim shot, you must strike both the head and the
rim of the pad simultaneously.
Output Jack
Specifications
PD-8
Pad Size:
Attaching the Pad to a Stand
Triggers:
2 (Head, Rim)
Dimensions:
226 (W) x 280 (D) x 54 (H) mm
Weight:
1.2 kg
2 lbs 11 oz
Attach the PDX-8 to a pad mount of the stand.
fig.PD-Set.e
Tighten
Loosen
Rod
Pass the rod through the pipe that is inside the holder.
When attaching the PD-8s to the mounts, be sure to
tighten the stand fixing screws securely. If any of them
remain loose, the pad could fall off.
8
8.5 inches
8-15/16 (W) x 11-1/16 (W) x 2-1/8 (H) inches
TD-6KW_e 9 ページ 2006年1月24日 火曜日 午後6時3分
CY-5
2. Mount the CY-5 so itUSING
fits the THE
lower
clutch
as
UNIT
SAFELY
shown below.
(Hi-Hat)
fig.CY-8.e
Pad Face
Bow Portion
Edge Portion
Projection (Be sure to
orient it correctly)
Output Jack
Making the Settings
When mounting the CY-5 on an L-Rod (pad mount),
use ONLY the attachment set as shown below.
3. Place the clutch felt (S), and while applying
some pressure, mount the upper clutch as
shown.
Afterwards, you can adjust the upper clutch to have the
movement you desire. If it is too loose, double triggering
may occur.
Be sure the ROLAND logo is on the opposite side of the
playing area.
Upper Clutch
Clutch Felt (S)
Apply pressure
Tighten the bolt with
a tuning key.
Clutch Felt (L)
Lower Clutch
1. Mounting the lower clutch and the clutch felt
(L).
Align the notched section as shown below. Then place the
clutch felt (L) so it fits securely.
Notch
(Be sure to
orient it correctly)
Specifications
CY-5
Size:
10 inches
Triggers:
2 (Bow, Edge)
Dimensions:
246 (W) x 246 (D) x 45 (H) mm
9-11/16 (W) x 9-11/16 (D) x 1-13/16 (H)
inches
Weight:
380 g
14 oz (without attachment)
Accessories:
Attachment Set for Hi-Hat (Upper Clutch,
Lower Clutch, Clutch Felt (L), Clutch Felt (S))
Tighten the bolt with
a tuning key.
add
* Continuous playing may cause dis-coloration of the pad, but
this will not affect the Pad's function.
9
TD-6KW_e 10 ページ 2006年1月24日 火曜日 午後6時3分
USING THE UNIT SAFELY
CY-8
(Crash Cymbal/Ride Cymbal)
Playing the CY-8
Bow Shot
fig.CY-8.e
Pad Face
Bow Portion
Edge Portion
Output Jack
This is the most common playing method, playing the pad
face of the cymbal. It corresponds to the sound of the “headside” of the connected trigger input.
fig.CY-Bow.e
Bow
Edge Shot
This playing method involves striking the edge with the
shoulder of the stick. It corresponds to the sound of the “rimside” of the connected trigger input.
Attaching the Cymbal Pad to a Stand
1. Use a tuning key to tighten the stopper bolt.
* To make use of edge shot, you’ll need to connect to a trigger
input jack on the percussion sound module that accommodates
rim shots.
fig.CY-Edge.e
Edge
The stopper keeps the cymbal pad from turning, and
prevents the cables from catching or getting tangled on
the stand.
fig.CY-Set01.e
Stopper
(Be sure to
orient it correctly)
Tighten the bolt with
a tuning key.
Choking
Choking (pinching) the cymbal’s edge with the hand
immediately after hitting the cymbal makes the sound stop.
2. Attach the CY-8 so the Roland logo is
positioned on the opposite side of the playing
area.
* To make use of choking play techniques, you’ll need to connect
to a trigger input jack on the percussion sound module that
accommodates rim shots.
fig.CY-Choke
3. Tighten the wing nut to obtain the desired
movement.
Use the included felt washer and the wing nut.
fig.CY-Set02.e
Wing Nut
Felt Washer
Double sounding may occur if the wing nut is loose.
Specifications
CY-8
Size:
Triggers:
Dimensions:
Weight:
Accessories:
12 inches
2 (Bow, Edge)
290 (W) x 295 (D) x 47 (H) mm
11-7/16 (W) x 11-5/8 (D) x 1-7/8 (H) inches
650 g / 1 lb 7 oz
Wing Nut, Felt Washer, Stopper
* Continuous playing may cause dis-coloration of the pad, but
this will not affect the Pad's function.
10
TD-6KW_e 11 ページ 2006年1月24日 火曜日 午後6時3分
USING THE UNIT SAFELY
FD-8
(Hi-Hat Control Pedal)
Using the FD-8
Using the FD-8, you can control the opening and closing of the
hi-hat sound.
fig.FD-8.e
Adjusting the Travel of the Pedal
Loosen the nut with a tuning key.
After adjusting, tighten the nut.
Open Hi-Hat
Strike the hi-hat without pressing the pedal
deep
Shift the Arm
Half Open Hi-Hat
Strike the hi-hat with the pedal pressed half-way
shallow
Closed Hi-Hat
Pedal Plate
Anchor Bolt
Strike the hi-hat with the pedal pressed
Foot Closed
Completely press down the pedal
Control Out Jack
Foot Open
Press the pedal and then immediately release it
Attaching the Anchor Bolts (When Using on the Carpet)
Anchor Bolt
Spring for
the Anchor Bolt
• The tips of the anchor bolts are sharp. Handle with care.
• When using on flooring, the anchor bolts may damage
the floor. Do not attach the anchor bolts.
• When the FD-8 is not going to be used for a long period
of time, move and fix the arm, allowing longer travel for
the pedal.
• To avoid damage, do not leave the FD-8 for extended
periods of time with the pedal plate depressed.
The volume of the Foot Closed sound can be adjusted
separately (TD-6V Owner’s Manual; p. 66).
• Connect the FD-8 to the TD-6V before turning on the
power.
• Do NOT press the pedal when turning on the power.
Specifications
FD-8
Dimensions:
130 (W) x 396 (D) x 103 (H) mm
Weight:
1.3 kg
2 lbs 14 oz
Accessory:
Tuning Key
5-1/8 (W) x 15-5/8 (D) x 4-1/16 (H) inches
11
TD-6KW_e 12 ページ 2006年1月24日 火曜日 午後6時3分
3. Use a tuning key to tighten the screws removed
in Step 1 so that the stand is firmly secured.
USING THE UNIT SAFELY
KD-8
(Kick)
fig.KD-Assy03
fig.KD-8.e
Output Jack
Head
Stand
Anchor Bolt
4. Attach the kick pedal.
Foot Plate
Making the Settings
1. Remove the screws attached to the reverse side
of the KD-8’s trigger.
Position the beater so that it strikes the center of the head,
then secure the kick pedal and KD-8 firmly in place.
fig.KD-Assy04.e
Beater
fig.KD-Assy01
Install the kick pedal securely.
Adjusting the Foot Plate Height
2. Pull out the stand in the direction indicated by
the arrow until it is fully extended.
fig.KD-Assy02
Depending on your kick pedal, it can be unstable when you
attach it to the KD-8. Be sure to adjust the foot plate height so
that the entire bottom surface of the pedal is attached to the
floor.
fig.KD-Assy05.e
Beater
Commercially Available Kick Pedal
* Adjust the height so that the entire pedal comes
into contact with the floor.
12
TD-6KW_e 13 ページ 2006年1月24日 火曜日 午後6時3分
1. Loosen the stand’s anchor bolts and remove
the foot plate.
fig.KD-Assy06
Adjusting the Anchor
Bolts
USING
THE UNIT SAFELY
When using the kick pedal on a carpet or similar surface,
adjust the anchor bolts so their tips protrude from the plate
and secure the pedal in place; this will make it easier to use the
kick pedal.
However, when used on flooring, the anchor bolts may
damage the floor. Adjust the anchor bolts correctly.
fig.KD-Anchor.e
Adjusting the Anchor Bolts
When Using on the Carpet
When using on the Floor
The tips of the anchor bolts are sharp. Handle with care.
2. Set the kick pedal so that the entire bottom
surface is attached to the floor.
When Using a Twin Pedal
3. In most cases, the stand becomes somewhat
floated. Tighten the anchor bolts securely there
to fix the stand and foot plate.
fig.KD-Pedal1
Position the two beaters
equally apart from the center
of the pad as shown in the
figure at left. If one of the
beater is further away from the
center than the other, the
sound from the further beater
will be lower in volume, or
will not sound as desired.
fig.KD-Assy07.e
This hight will vary depending
on your kick pedal.
fig.KD-Pedal2
Using a twin pedal will result
in lower sensitivity as
compared to when a single
pedal is used. Raise the
sensitivity on the sound
module.
• Install the kick pedal securely.
• Take care not to pinch your fingers.
• The tips of the anchor bolts are sharp. Handle with care.
• When moving the setup, be sure to remove the screws
and fold the stand. Transporting the KD-8 while it
remains open may subject the stand to excessive strain
and result in damage to the stand.
Specifications
KD-8
Dimensions:
272 (W) x 260 (D) x 405 (H) mm
10-3/4 (W) x 10-1/4 (D) x 16 (H) inches
Weight:
2.9 kg
6 lbs 7 oz
Accessories:
Screws
* Continuous playing may cause dis-coloration of the pad, but
this will not affect the Pad's function.
13
TD-6KW_e 14 ページ 2006年1月24日 火曜日 午後6時3分
. USING THE UNIT SAFELY
Assemble the “TD-6KW”
921
Using the provided cables, connect the pads.
Connect the L-shaped plugs of the included cables to the pads.
To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power
on all devices before making any connections.
fig.Setting1.e
HH SNR KIK
RD
HHC
CR1 T3 T2 T1
CR1
RD
CY-8
CY-8
T1
HH
T2
PD-8
PD-8
CY-5
TD-6V
PDX-8
T3
PD-8
SNR
KIK
KD-8
HHC
FD-8
fig.Label
1. Insert the plugs of connecting cables into the TRIGGER INPUTS jacks on the
rear of the TD-6V.
2. Insert the L-sharped plugs into the TRIGGER OUTPUTS jacks of the pads.
* When you connect the cables, please refer to the marking label that is attached on both edge of the cables.
14
SNR
TD-6KW_e 15 ページ 2006年1月24日 火曜日 午後6時3分
.
USING THE UNIT SAFELY
Trigger Settings for the TD-6V
For the Snare (PDX-8) to function correctly, trigger parameters in the sound module
TD-6V must be adjusted.
For more detailed informations, refer to the TD-6KV Owner’s Manual.
Adding the Optional Pads to the TD-6KW
When adding the new pad, use trigger input 10 (CRASH2).
With the optional cable (PCS-31L) or a standard insert cable, you can connect two pads to the triger inputs 5/6
(TOM2/AUX) and 7/8 (TOM3/4). You can use up to 11 pads at the same time.
*
When connecting two pads to 1 input (5/6 or 7/8), rim shots are not be possible. For more information, refer to TD-6V
Owner’s Manual p.70.
Examples
Adding a Cymbal
TD-6V Rear Panel
Adding the CY-8 or the CY-5 for a
2nd Crash or a Splash Cymbal. For
mounting, use the Cymbal Mount
MDY-10U.
Adding a Tom
Adding the PD-8 for a 2nd floor
tom.
PCS-31L
Connect the PD-8 to the trigger
input 10 (CRASH2).
With the optional cable (PCS-31L),
you can also connect two PD-8s to
the trigger input 7/8 (TOM3/4).
For mounting, use the Pad Mount
MDH-10U.
PD-8
PD-8
Options
Kick Trigger Pad:
KD-8, KD-7
V-Kick Trigger Pad:
KD-85, KD-120
Dual Trigger Pad:
PD-8
V-Pad:
PDX-8, PD-85, PD-105, PD-125
Cymbal Pad:
CY-8, CY-5
V-Cymbal:
CY-12R/C, CY-14C, CY-15R
Pad Mount:
MDH-10U
Cymbal Mount:
MDY-10U
Connection Cable:
PCS-31L
15
TD-6KW_e 16 ページ 2006年1月24日 火曜日 午後6時3分
Information
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
PHILIPPINES
COSTA RICA
TRINIDAD
NORWAY
JORDAN
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
JUAN Bansbach Instrumentos
Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
AMR Ltd
Ground Floor
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868) 638 6385
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
SINGAPORE
CURACAO
URUGUAY
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
SWEE LEE MUSIC
COMPANY PTE. LTD.
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
POLAND
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
PORTUGAL
LEBANON
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
Chahine S.A.L.
Gerge Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 165857
Beirut, LEBANON
TEL: (01) 20-1441
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
TEL: (02) 2561 3339
That Other Music Shop(PTY)Ltd.
11 Melle St., Braamfontein,
Johannesbourg,
SOUTH AFRICA
TEL: (011) 403 4105
FAX: (011) 403 1234
THAILAND
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
VIETNAM
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
TEL: (010) 6426-5050
Roland Shanghai Electronics
Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie
Yi Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
TEL: (020) 8736-0428
HONG KONG
Theera Music Co. , Ltd.
330 Soi Verng NakornKasem,
New Road, Sumpantawongse,
Bangkok 10100, THAILAND
TEL: (02) 224-8821
SAIGON MUSIC
DISTRIBUTOR
(TAN DINH MUSIC)
138 Tran Quang Khai Street
Dist. 1, Ho Chi Minh City
VIETNAM
TEL: (08) 848-4068
AUSTRALIA/
NEW ZEALAND
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
CENTRAL/LATIN
AMERICA
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
TEL: 2415 0911
ARGENTINA
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
BARBADOS
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
KOREA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
MALAYSIA
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
TEL: (574)3812529
DOMINICAN REPUBLIC
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
ECUADOR
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final
Alameda Juan Pablo II,
Edificio No.4010 San Salvador,
EL SALVADOR
TEL: 262-0788
GUATEMALA
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
TEL:(502) 599-2888
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
MARTINIQUE
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
TEL: (55) 5668-6699
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (505)277-2557
PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE
PANAMA
TEL: 315-0101
PARAGUAY
Distribuidora De
Instrumentos Musicales
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (595) 21 492147
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - Peru
TEL: (511) 4461388
VENEZUELA
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
EUROPE
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
CZECH REP.
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
TEL: (2) 666 10529
DENMARK
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
FINLAND
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
TEL: (23) 511011
IRELAND
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
ROMANIA
KUWAIT
OMAN
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
TEL: (266) 364 609
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
RUSSIA
MuTek
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
SPAIN
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
QATAR
Al Emadi Co. (Badie Studio &
Stores)
P.O. Box 62, Doha, QATAR
TEL: 4423-554
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary
Bldg., 1st Floor, Alkhobar,
SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SYRIA
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
UKRAINE
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
TURKEY
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo,
UKRAINE
TEL: (03131) 414-40
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
U.A.E.
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
MIDDLE EAST
BAHRAIN
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 17 211 005
CYPRUS
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (022) 66-9426
IRAN
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021) 285-4169
ISRAEL
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai,
U.A.E.
TEL: (04) 3360715
NORTH AMERICA
CANADA
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way
Richmond B. C., V6V 2M4
CANADA
TEL: (604) 270 6626
Roland Canada Music Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha'aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
As of December 10, 2005 (ROLAND)
04234201
2PR