Volvo G726B User's Manual

VOLVO MOTOR GRADER
G726B
ALL WHEEL DRIVE
• Configuration: Articulated frame
• Engine model: Volvo D7DGDE2
• Maximum net engine output
@2200 RPM (per SAE J1349):
198 - 235 hp (148 - 175 kW)
• Base weight: 35,400 lb (16 057 kg)
• Blade down force:
17,854 lb (8 099 kg)
• Blade pull:
All Wheel Drive – 28,019 lb (12 709 kg)
Tandem – 20,519 lb (9 307 kg)
• Single lever “Smart Shifter” transmission
control with gear memory feature
• 8400 fully sequential direct drive powershift
transmission
• Separate hydraulic pump & speed sensor
for each front wheel
• Choice of fully enclosed, ROPS cab in full
height or low profile configuration, or
ROPS canopy
• Variable aggression for job matching
• Maintains aggression at both front wheels
through turns
• Creep feature allows hydrostatic drive at
front wheels from 0-2.0 mph (0-3,2 km/h)
for optimum fine grading
• Wheel motor efficiencies maintained in both
forward and reverse
• AWD available at speeds up to 20.2 mph
(32,5 km/h)
• Moveable Blade Control System
• Load sensing, Closed Center Hydraulic
System
• Fully adjustable control pedestal with low
effort hydraulic controls
• Full front and rear frame sections designed
for attachment mounting
Base operating weight
(Standard equipment)
Weight adjustments for various options are
listed.
Typically equipped operating weight:
includes 14' x 25" x 7/8" (4 267 x 635 x 22 mm)
moldboard and scarifier.
G726B . . . . . . . . . . . . . . . . . 37,420 lb (16 973 kg)
800
1100
720
1000
640
900
800
700
600
500
400
Gross torque (lb.ft)
G726B
Total . . . . . . . . . . . . . . . . . . . 35,400 lb (16 057 kg)
On front wheels . . . . . . . . . . 10,266 lb (4 657 kg)
On rear wheels . . . . . . . . . . . 25,134 lb (11 401 kg)
torque vs. engine speed
1200
Gross torque (Nm)
Weights shown include full cab with ROPS, all
operating fluids and operator.
Engine performance curve
560
480
400
320
240
300
200
100
0
160
80
0
1000
Productivity
(Standard equipment)
Maximum blade pull (no wheel slip, 0.85 traction
co-efficient). . . . . . . . . . . . . . 28,019 lb (12 709 kg)
Blade down force
• cutting capability
(ISO 7134) . . . . . . . . . . . . . 17,854 lb (8 099 kg)
Blade down force is the maximum downward
force which may be applied at the cutting
edge.
Engine data
Make/Model . . . . . . . . . . . . . . . . . . Volvo D7DGDE2
Type . . . . . . . . . 4 Cycle, Turbocharged, Aftercooled
No. of cylinders . . . . . . . . . . . . . . . . . . . . . . In Line 6
Bore & stroke . . . . . 4.25" x 5.11" (108 x 130 mm)
Displacement . . . . . . . . . . . . . . . . . 436 cu in (7,1 l)
Maximum net engine output @ 2200 RPM
(per SAE J1349) . . . . . . 198-235 hp (148-175 kW)
Rated gross brake horsepower @ 2200 RPM
• Gears forward 1, 2 and
Reverse 1 . . . . . . . . . . . . . . . . . 205 hp (153 kW)
Rated gross brake horsepower @ 2200 RPM
• Gears forward 3-8 and
Reverse 2-4 . . . . . . . . . . . . . . . 241 hp (180 kW)
Rated net brake horsepower @ 2200 RPM
• Gears forward 1, 2 and
Reverse 1 . . . . . . . . . . . . . . . . . . 198 hp (148 kW)
Torque @1100 RPM . . . . . . . . 664 lb.ft (900 N.m)
Torque rise . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35%
Rated net brake horsepower @ 2200 RPM
• Gears forward 3-8 and
Reverse 2-4 . . . . . . . . . . . . . . . . 235 hp (175 kW)
Torque @1400 RPM . . . . . 774 lb.ft (1 050 N.m)
Torque rise . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34%
All Wheel Drive engaged
Rated gross brake horsepower @ 2200 RPM
• All gears . . . . . . . . . . . . . . . . . . . 241 hp (180 kW)
Rated net brake horsepower @ 2200 RPM
• All gears . . . . . . . . . . . . . . . . . . . 235 hp (175 kW)
Torque @ 1400 RPM . . . . . 774 lb.ft (1 050 N.m)
Torque rise . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34%
Performance: Rated net brake horsepower
SAE standard J1349/ISO 3046-2 conditions
with water pump, fuel system, air cleaner,
muffler, alternator, cooling fan and lubricating
oil pump.
1200
1400
1600
1800
Engine speed (rpm)
Engine data
(continued)
Engine equipped with a two stage, dual
element, dry type air cleaner with exhaust
aspirator and service indicator. 24 volt starting
and electrical system with 75 amp (1800 watt)
brushless alternator with internal voltage
regulator. Two heavy duty 12 volt maintenance
free batteries with 660 cold cranking amps
(CCA) and 160 minutes reserve capacity per
battery. 950 CCA batteries available optionally.
System includes battery disconnect.
Transmission
Make/Model . . . . . . . . . . . . . . . . . Volvo 8400
Fully sequential, direct drive, powershift
transmission. Engine cannot be started if
transmission is in gear. Single lever “Smart
Shifter” electronic transmission controller
provides self-diagnostics. The flywheel
mounted, multi-disc master clutch is oil cooled
and lubricated for long life.
Ground speeds at 2200 RPM with standard
tires:
Forward
Gears.....mph ........km/h
1................2.8 ...........4,4
2................3.9 ...........6,2
3................5.3 ...........8,5
4................7.5.........11,9
5 .............10.5.........16,9
6 .............14.7.........23,6
7 .............20.4.........32,7
8 .............28.5.........45,7
Reverse
Gears.....mph ........km/h
1................2.8 ...........4,4
2................5.3 ...........8,5
3 .............10.5.........16,9
4 .............20.4.........32,7
Transmission guard is standard equipment and
is hinged for easy access.
Differential / Final drive
Make/Model . . . . . . . . . . . . . . . . . Volvo SR30
Single reduction final drive with an operator
controlled lock/unlock differential. Rear axles
are induction hardened, supported on double
row spherical roller bearings.
2000
2200
Tandems
Oscillating tandem case has internal gusseting
for maximum torsional strength. Field-proven
split ring/flanged sleeve tandem mounting and
1" (25 mm) thick inner wall resists flexing from
side loading during severe applications.
Depth . . . . . . . . . . . . . . . . . . . . . . 24.50" (622 mm)
Width . . . . . . . . . . . . . . . . . . . . . . . 8.25" (210 mm)
Thickness • inner wall . . . . . . . . . . . . 1.00" (25 mm)
• outer wall . . . . . . . . . . . . 0.75" (19 mm)
Center distance. . . . . . . . . . . . . 61.50" (1 562 mm)
Drive chain pitch . . . . . . . . . . . . . . . . 2.00" (51 mm)
Oscillation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15º
Brakes
Service Brakes: Foot operated
Fade resistant, hydraulically actuated, oil disc
service brakes located at the 4 tandem drive
wheels are self-adjusting, fully sealed and
maintenance free. System features crossover
dual braking circuits for uniform braking on
both sides of the grader. Includes reserve
power assist and operator warning system
(visual and audible).
Parking Brake
Spring applied hydraulic release independent,
disc type parking brake on transmission output
shaft and effective on all 4 tandem drive
wheels. Includes visual and audible operator
warning system for parking brake on,
transmission in gear condition. Transmission
will not engage with park brake on.
Braking systems to SAE Recommended
Practice J1473 OCT. 90, and J1152 APR. 80;
ISO 3450-1993-01-28. Volvo uses asbestos
free brake components.
Wheels & tires
(Standard equipment)
Tire size . . . . . . . . . . . . . . . . . . . . . . 14:00 x 24, G-2
Ply rating (PR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Rim size . . . . . . . . . . . . . . . . . . . . . 10.0" (254 mm)
Bolt-on rims are not interchangeable between
the front wheels and the tandem wheels.
Front axle
Type: Fully welded steel truss, gusseted for
torsional strength, oscillates on a single 3.5”
(89 mm) diameter center pivot pin.
Wheel lean . . . . . . . . . . . . . . . . . . . . . . . . . 15º R & L
Oscillation . . . . . . . . . . . . . . . . . . . 16º up and down
Ground clearance. . . . . . . . . . . . . . 24.0" (610 mm)
Two 3" (76 mm) diameter wheel lean cylinders
and lock valve are standard equipment.
All Wheel Drive
The Volvo high torque All Wheel Drive System
incorporates two variable displacement, closed
loop piston pumps. The Volvo AWD design
automatically adjusts hydraulic flow and
pressure to the drive system to match tandem
wheel speeds in all tractive conditions. Each
front wheel is independently powered by a 2
speed motor. Each motor is controlled by its
own speed sensor and pump. The All Wheel
Drive system is controlled by the operator
through a positive On/Off switch as well as a
16 position variable aggression dial. The front
wheel speed sensors will always match front
wheel speed to tandem wheels speed relative
to the level of aggression selected by the
operator. This provides optimum job matching
All Wheel Drive
(continued)
in all tractive conditions. When AWD is
selected, the engine will deliver maximum VHP
horsepower regardless of the working gear
being used.
Typical operating pressure . . . . 3,000 psi (206 Bar)
Maximum operating pressure . . 5,000 psi (344 Bar)
Minimum operating pressure . . . . . 500 psi (34 Bar)
Top speed . . . . . . . . . . . . . . 20.2 mph (32.5 km/h)
Creep Mode speed . . . . . . . 0-2 mph (0-3.2 km/h)
Maximum rim pull . . . . . . . . . . . 7,500 lb (3 402 kg)
The Volvo high torque All Wheel Drive System
operates in forward gears 1-7 and reverse
gears 1-4. The operator may shift from 7th
AWD into 8th and back to 7th AWD at any
time for maximum high speed performance.
In addition, the Volvo system provides the
operator with the ability to fine grade in Creep
Mode using only hydrostatic front wheel drive.
The Volvo high torque All Wheel Drive System
offers infinite speed control below 2 mph (3,2
km/h) for fine grading as well as a top speed
of 20.2 mph (32,5 km/h) for snow plowing.
The AWD controller is integral with the
electronic 8400 transmission controller,
thereby supplying the same diagnostic
features found in the Volvo 8400 transmission.
All Wheel Drive
(continued)
Volvo AWD motors maintain maximum
efficiency in both forward and reverse.
Operating modes
All Wheel Drive or Tandem Drive
• On-Off Selection
• Creep Mode - Hydrostatic front wheel drive
only for optimum control and manouverability
while fine grading.
• Manual Mode - Allows the operator to match
front wheel agression setting to specific
applications.
AWD features
• Maximum startup torque
• Power maintained in either direction
• Smooth operation in low speeds
• Maintains front wheel agression in turns
• One speed sensor at each front wheel
• Hydrostatic Creep Mode feature
Circle drive
Steering
Hydrostatic power front wheel steering
incorporating two steering cylinders. Meets
SAE J1511 OCT. 90 with optional secondary
steering.
Minimum turning radius using front axle steering,
articulation, wheel lean and unlocked differential
. . . . . . . . . . . . . . . . . . . . . . . . . . . 25'6" (7 772 mm)
Steering arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72º
Frame articulation angle . . . . . . . . . . . . . . . . . . . 22º
Articulation lock standard.
The Volvo dual cylinder Circle Drive System
uses direct acting hydraulic power for
exceptional turning and holding capability
under full load. Circle Drive System uses
hardened drive pinions and is protected
against impact damage by an overload cushion
valve as standard equipment.
Hydraulic drive cylinders . . . . . . . . . . . . . . . . . . . . . 2
Points of leverage . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360º
Drawbar
Frame
Full front and rear frame sections.
Front: Fully welded box section. Dual sloped
front frame provides excellent forward visibility.
Minimum dimensions of
box section . . . . . . . 10.5" x 14.0" (267 x 356 mm)
Plate thickness . . . . . . . . . . . . . . . . . 0.75" (19 mm)
Vertical section modulus
at arch . . . . . . . . . . . . . . . . . . 119 cu in (1 950 cm3)
minimum . . . . . . . . . . . . . . . 101.5 cu in (1 663 cm3)
maximum . . . . . . . . . . . . . . . . 212 cu in (3 474 cm3)
Linear weight - minimum-maximum . . . . . . . . . . . . . .
107.1 - 232.5 lb/ft (159.4 - 346.0 kg/m)
Rear: Full perimeter rear frame permits modular
powertrain mounting for ease of service and is
ideal for attachment mounting. Optional first user
lifetime warranty on frame and articulation joint.
Minimum dimensions of
rear frame . . . . . . . . . 4.0" x 10.0" (102 x 254 mm)
Plate thickness . . . . . . . . . . . . . . . . . . 0.5" (13 mm)
Articulation
Twin 4.5" (114 mm) hydraulic cylinders
articulate frame 22º right and left. Anti-drift lock
valve ensures stable operation.
Circle
Hardened teeth, cut on the outside of the circle
for maximum leverage and minimum wear.
The circle is supported at six points by three
adjustable clamp plates and three adjustable
guide shoes, providing optimum circle support
and load distribution. DURAMIDE™ faced
clamp and guide shoes prevent metal-to-metal
contact and provide maximum service life.
DURAMIDE™ is a synthetic bearing material
that maximizes service life and reduces circle
system maintenance requirements.
Diameter . . . . . . . . . . . . . . . . . . 66.25" (1 683 mm)
Thickness . . . . . . . . . . . . . . . . . . . . 1.25" (32 mm)
Adjustable guide shoes. . . . . . . . . . . . . . . . . . . . . . 3
Adjustable clamp plates . . . . . . . . . . . . . . . . . . . . . 3
Fully welded box section. Narrow “T” design
permits optimum visibility to the work area.
Drawbar ball stud provides an adjustment to
compensate for different tire sizes. Blade lift
cylinder anchors are straddle mounted on
drawbar to provide maximum strength and
support.
Dimensions of
box section . . . . . . . . . 6.5" x 6.5" (165 x 165 mm)
Plate thickness . . . . . . 1.0" & 0.75" (25 & 19 mm)
Moldboard
Standard moldboard with
replaceable end bits . . . . . . . . . . . . 12' x 25" x 7/8"
(3 658 x 635 x 22 mm)
Blade material . . . . . . . SAE 1050 high carbon steel
Edge: through hardened . . . . . 6" x 5/8" boron steel
(152 x 16 mm)
Bolt spacing. . . . . . . . . . . . . . . . . . . . . 6" (152 mm)
• bolt size . . . . . . . . . . . . . . . . . . . . . . 5/8" (16 mm)
Slide rails
bearings.
supported
by
DURAMIDE™
Blade range:
Moveable Blade Control System
(Dimensions shown with standard moldboard)
LEFT
RIGHT
Reach outside tires - articulated
frame .......120.0" (3 048 mm)....119.5" (3 035 mm)
Reach outside tires - straight
frame..........79.5" (2 019 mm)..........79" (2 007 mm)
Blade slide ...26.5" (673 mm)..........26.5" (673 mm)
Circle side
shift ................30.5" (775 mm)..........29.5" (749 mm)
Maximum bank
sloping angle........................90º...................................90º
Blade ground clearance .....................17.5" (445 mm)
Blade cutting depth.............................32.0" (813 mm)
Blade tilt range............................44º forward 6.5º back
Superior blade mobility permits steep ditch
cutting angles and back sloping without
putting the front tire on the slope.
Cab & controls
All controls are located in a 90° arc forward
and to the right of the operator. Located
forward of the operator are the engine oil
pressure, coolant temperature and fuel level
gauges, transmission gear indicator and a
multi-function Contronic monitoring display.
Located in the fully adjustable steering
pedestal are the following switches: differential
lock/unlock, hazard lights, combination turn
signal, horn and high beam headlight. Heater
and wiper/washer controls, lighting and
accessory switches are grouped in the
operator’s right hand console. This console
also
contains
the
ignition
key
and access to the circuit breaker and fuse
panel. Located to the right of the operator,
above the console, are the AWD On/Off
switch, a 16 position variable aggression dial
and the hydrostatic Creep On/Off switch.
An accelerator/decelerator foot pedal and
slider type hand throttle are standard
equipment. Outside mounted rear view mirrors
(L&R) are standard. Interior operator noise
level ranges from 78 to 81 dB(A) per ISO
6394 (enclosed cab).
Cab options
• High capacity heater/air conditioner c/w
adjustable vents, temperature control and 3
speed fan
• Fully adjustable, suspension seat
• Lower opening front windows
• Rear windshield wipers and washers
• Lower front window wipers and washers
• Modular, 24 volt radio and cassette player
with remote control
• Operator Convenience Package (lunch box,
steel vacuum bottle and holder, ashtray)
• 24 volt to 12 volt convertor for electrical
accessories or two way radio installations
Full height cab with ROPS
Inside dimensions
Height . . . . . . . . . . . . . . . . . . . . . 74.0" (1 880 mm)
Width @ controls . . . . . . . . . . . . 56.0" (1 422 mm)
Depth @ controls . . . . . . . . . . . . 55.5" (1 410 mm)
An optional Low Profile Cab is available with
an inside height of 62" (1 575 mm). All Volvo
Grader cabs and canopies are designed to
meet or exceed SAE J1040 APR. 88, ISO
3471/1-1986(E), and 86/295/EEC ROPS
requirements. The seatbelt is 2" (51 mm) wide
and meets SAE J386 JUNE 93; ISO 66831981(E).
Capacities
Load sensing hydraulics
Closed Center Hydraulic System senses load
requirements and maintains system pressure
350 psi (24 Bar) above the load pressure.
System features industry standard control
arrangement complete with low effort,
feathering type, short throw levers located on a
fully adjustable control pedestal.
System incorporates lock valves to prevent
cylinder drift under load in the following
circuits: blade lift, moldboard tilt, circle shift,
wheel lean and articulation.
Hydraulic system features include axial piston
pump, pressure and flow compensated,
variable displacement with high output for
smooth multi-functioning.
Maximum pressure . . . . . . . . . . 2,700 psi (186 Bar)
Output 2200 RPM. . . . 0-75 U.S. gpm (0-284 lpm)
Filtration . . . . . . . . . . . . . . . . 10 micron spin-on type
U.S.Gal. Imp.Gal. Litres
Fuel tank . . . . . . . . . . 100.0 . . . . . 83.3. . . . . 378.5
Transmission . . . . . . . . 10.0 . . . . . . 8.4 . . . . . . 38.0
Final drive . . . . . . . . . . . . 6.0 . . . . . . 5.0 . . . . . . 23.0
Tandems (each) . . . . . . 26.4 . . . . . 22.0. . . . . 100.0
Hydraulic oil tank . . . . . 35.4 . . . . . 29.5. . . . . 134.0
Coolant antifreeze protection to
-58º F (-50º C) approx . 12.4 . . . . . 10.3 . . . . . . 47.0
Engine oil . . . . . . . . . . . . 5.0 . . . . . . 4.2 . . . . . . 19.0
Attachments
“A” Frame. . . . . . . . . . . . . . . . . . . 700 lb
(318 kg)
Snow
Hydraulic Wing
• high-bench . . . . . . . . . . . . . . . 4,800 lb
• low bench . . . . . . . . . . . . . . . 4,000 lb
One Way Plow. . . . . . . . . . . . . 2,350 lb
“V” Snow Plow
• 9' (2 743 mm). . . . . . . . . . . . 2,500 lb
• 10' (3 042 mm) . . . . . . . . . . 2,650 lb
(1 134 kg)
(1 202 kg)
Earth
Dozer Blade
• 8' (2 438 mm). . . . . . . . . . . . 2,620 lb
• 9' (2 743 mm). . . . . . . . . . . . 2,870 lb
•10' (3 048 mm) . . . . . . . . . . . 3,120 lb
Front Mounted Scarifier . . . . . . 1,780 lb
Mid-mount Scarifier . . . . . . . . . 1,725 lb
Push Block . . . . . . . . . . . . . . . . 1,050 lb
Ripper/Scarifier, rear . . . . . . . . 2,880 lb
Windrow Eliminator . . . . . . . . . 1,300 lb
(1 188 kg)
(1 302 kg)
(1 415 kg)
(807 kg)
(782 kg)
(476 kg)
(1 306 kg)
(590 kg)
(2 177 kg)
(1 814 kg)
(1 067 kg)
Dimensions
B Overall width . . . . . . . . . . 8'4" (2 540 mm)
C Overall height . . . . . . . . . 11'2" (3 404 mm)
• with Low
Profile Cab . . . . . . . . . . . 10'2" (3 099 mm)
F Tread width. . . . . . . . . . . 6'10" (2 083 mm)
A Overall length . . . . . . . . 29'11" (9 119 mm)
D Wheelbase . . . . . . . . . . . 20'0" (6 096 mm)
E Bladebase
• ISO 7134. . . . . . . . . . . . 8'6" (2 591 mm)
C
O
V
E
R
A
L
L
H
E
I
G
H
T
E - BLADEBASE
D - WHEELBASE
A - OVERALL LENGTH
F - TREAD WIDTH
B - OVERALL WIDTH
STANDARD FEATURES
Volvo “High Torque” All Wheel Drive with hydrostatic
Creep feature
Operator controlled, lock/unlock differential final
drive
4 wheel, crossover, dual braking system with reserve
power assist
Park brake with operator warning alarm and
indicator
Fully sequential, direct drive, powershift 8400
transmission, with transmission guard
13.5" (343 mm) diameter, 4 plate, full oil master
clutch
Moveable Blade Control System for optimum blade
mobility
Full front and rear frame sections designed to
withstand shock loading of rear attachments
Circle drive counter-balance valve protects circle
drive against impact damage
Hardened circle teeth cut on outside of circle for
maximum turning power
Hardened circle drive pinions for maximum wear
resistance
Isolation mounted cab, transmission and engine for
reduced noise and vibration
Adjustable steering control pedestal with tilt head
for maximum operator comfort
Gauges include: coolant temperature, engine oil
pressure, fuel, hourmeter, dash mounted air
cleaner service indicator, articulation angle
indicator, multi-function Contronic Monitoring
System with visual and audible warnings
Load sensing, Closed Center Hydraulic System with
short throw, low effort control levers. Hydraulically
operated blade lift, circle turn, moldboard slide
and tilt, circle shift and wheel lean functions.
Feathering type controls for precise blade
adjustments
Suspension seat
100 U.S. gallon (378.5 l) fuel tank capacity
Dual leaning wheel cylinders
DURAMIDE™ wear strips on circle clamp plates and
guide shoes prevent metal-to-metal contact for
maximum service life
Hinged radiator guard for easy trash clean out
Backup lights
Backup alarm with automatic volume levels
Painted high gloss Volvo yellow and gray
Lockable tool box with storage space for scarifier
shanks
Engine side panels complete with locks
Left and right outside rear view mirrors
Interior rear view mirror
Exhaust aspirated air cleaner
Front cab wiper and washer
OPTIONAL EQUIPMENT
lb
kg
Accumulators - blade lift (2). . . . . . . . . . . 122
55
Air conditioner - 29,000 BTU
• HFC-134a (non-CFC refrigerant) . . . . . 130
59
Brush guards . . . . . . . . . . . . . . . . . . . . . . . 40
18
Cab
• canopy shell with ROPS - deduct . . . (625) (284)
• FOPS protection for ROPS cabs . . . . . 220 100
• Low Profile Cab
with ROPS - deduct . . . . . . . . . . . . . . (270) (122)
Cab heater - 49,000 BTU • with cab
pressurizer and replaceable filter . . . . . . . 60
27
Defroster fans . . . . . . . . . . . . . . . . . . . . . . . . 3
1
Engine block heater . . . . . . . . . . . . . . . . . . . 3
1
Engine precleaner - Turbo II . . . . . . . . . . . . . 6
3
First user lifetime frame warranty . . . . . . . . . 0
0
Float control - right and left detent style
independent, electric . . . . . . . . . . . . . . . . 15
7
Hydraulic manifold cover . . . . . . . . . . . . . . 10
4
Hydraulic tank heater . . . . . . . . . . . . . . . . . . 3
1
24 volt radio/cassette player . . . . . . . . . . . . 6
3
Lights
• Beacon (amber or blue) . . . . . . . . . . . . . . 10
4
• Clearance lights front & rear . . . . . . . . . . . 2
1
lb
• Front mounted plow lights - 2
• high mount. . . . . . . . . . . . . . . . . . . . . 120
• low mount . . . . . . . . . . . . . . . . . . . . . 100
• Headlights with dimmer switch . . . . . . . . . 0
• Moldboards lights - 2 . . . . . . . . . . . . . . . . . 2
• Rear flood lights - 2 . . . . . . . . . . . . . . . . . . 2
• Snow wing lights - 2 . . . . . . . . . . . . . . . . . 2
Fenders
• Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
• Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
Moldboards
• 14' x 25" x 7/8"
(4 267 x 635 x 22 mm) . . . . . . . . . . . . 240
Moldboard extensions
R or L - 2' (610 mm). . . . . . . . . . . . . . . 190
Moldboard edges - carbide 3/4" x 5"
(19 x 127 mm) . . . . . . . . . . . . . . . . . . . . . . 100 amp alternator . . . . . . . . . . . . . . . . . . . . 0
Operator convenience package
• lunch box, steel vacuum bottle
and holder, ashtray . . . . . . . . . . . . . . . . . . 10
Paint - custom colors. . . . . . . . . . . . . . . . . . . Polar protection . . . . . . . . . . . . . . . . . . . . . . 0
kg
54
45
0
1
1
1
36
182
109
86
0
5
0
lb
Reflectors - rear/side . . . . . . . . . . . . . . . . . . . Remote lube manifold for articulation
cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
Remote valve for attachments
• 3 or 5 bank - remote mount . . . . . . . . . . . 85
Sideshift accumulator. . . . . . . . . . . . . . . . . 50
Rim locks included with 3 piece rims. . . . . . 0
Secondary steering (power assisted) . . . . 95
Tie down brackets . . . . . . . . . . . . . . . . . . 100
Tires
• 17.5 x 25, 12 PR, G-2,
14" (356 mm) rims. . . . . . . . . . . . . . . 375
Tool kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmission sump heater . . . . . . . . . . . . . . . Tropical protection . . . . . . . . . . . . . . . . . . . . . Vandalism protection . . . . . . . . . . . . . . . . . . 8
Wheel weights for rear
wheels only - each . . . . . . . . . . . . . . . . 250
Window - opening - lower front. . . . . . . . . . . Window - opening sliders - left/right . . . . . . . Wiper and washer - rear . . . . . . . . . . . . . . . . Wiper and washer - lower front. . . . . . . . . . . -
kg
0
39
23
0
43
45
170
4
113
-
Your safety and the safety of those around you depends on using care and judgement when operating and servicing your grader.
Do not operate the grader until you read and understand the warnings and instructions in the operator’s manual. Volvo Motor
Graders Limited is an ISO 9001 and 14001 registered company. www.volvo.com
Under our policy of continuous product development and improvement, we reserve the right to change specifications and design
without prior notice. The illustrations do not necessarily show the standard version of the machine.
Consult your Volvo dealer for recommended option and attachment selection.
Ref. No. 21 4 434 1005
English
Printed in Canada 2002.08-2.5 GRD
Volvo, Goderich