Black & Decker MS2000 Instruction manual

SMART SELECT MULTI- SANDER
INSTRUCTION MANUAL
Catalog
Number
MS2000
Thank you for choosing Black & Decker!
Go to www.BlackandDecker.com/NewOwner
to register your new product.
PLEASE READ BEFORE RETURNING THIS
PRODUCT FOR ANY REASON:
If you have a question or experience a problem with your Black & Decker purchase, go to
HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS
for instant answers 24 hours a day.
If you can’t find the answer or do not have access to the internet,
call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.
Please have the catalog number available when you call.
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energizing power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
2
facilities, ensure these are connected and properly used. Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger that
is suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool is
maintained.
SPECIFIC SAFETY RULES
• Hold power tools by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool "live" and shock the operator.
• Always use proper eye protection and a respirator when sanding.
• Sanding of lead-based paint is not recommended. See Sanding Lead Based Paint
for additional information before sanding paint.
• Clean your tool out periodically.
• Store sander with one of the platens in place.
• Keep hands away from spindle area on unit.
• Do not turn Smart Select knob when unit is running.
3
• Do not rest fingers on platen during use.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles away
from face and body.
WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI S12.6 (S3.19) hearing protection
• NIOSH/OSHA/MSHA respiratory protection
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property damage.
Symbols
The label on your tool may include the following symbols.
V ..........................volts
A..........................amperes
Hz ........................hertz
W ........................watts
min ........................minutes
......................alternating current
no ........................no load speed
......................direct current
..........................Class II Construction
........................earthing terminal
........................safety alert symbol
.../min ..................revolutions or
reciprocations per minute
4
Extension Cords
When using an extension cord, be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a drop in line voltage resulting in
loss of power and overheating. The following table shows the correct size to use
depending on cord length and nameplate ampere rating. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier the cord.
Recommended Minimum Wire Size for Extension Cords
Total Length of Cord
25 ft.
50 ft.
75 ft.
100 ft.
125 ft.
150 ft.
175 ft.
7.6 m
15.2 m
22.9 m
30.5 m
38.1 m
45.7 m
53.3 m
Wire Size AWG
18
18
16
16
14
14
12
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means
your tool will operate on standard 60 Hz household power. Do not operate AC tools on
DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC
or DC power. This information is printed on the nameplate. Lower voltage will cause loss
of power and can result in over-heating. All Black & Decker tools are factory-tested; if
this tool does not operate, check the power supply.
Functional Description Figure A
1. On/off switch
2. Smart Select dial
3. Release button
4. Random orbit sanding base
5. Dust canister
6. Large detail sanding base
7. Sanding base tip
8. Detail finger attachment
A
1
5
2
3
4
8
5
7
6
Sanding
Lead based Paint
Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling
the contaminated dust. The greatest danger of lead poisoning is to children and
pregnant women.
Since it is difficult to identify whether or not a paint contains lead without a chemical
analysis, we recommend the following precautions when sanding any paint:
Personal Safety
• No children or pregnant women should enter the work area where the paint sanding is
being done until all clean up is completed.
• A dust mask or respirator should be worn by all persons entering the work area. The
filter should be replaced daily or whenever the wearer has difficulty breathing.
NOTE: Only those dust masks suitable for working with lead paint dust and fumes
should be used. Ordinary painting masks do not offer this protection. See your local
hardware dealer for the proper (NIOSH approved) mask.
• NO EATING, DRINKING or SMOKING should be done in the work area to prevent
ingesting contaminated paint particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the
work area where dust would settle on them.
Environmental Safety
• Paint should be removed in such a manner as to minimize the amount of dust
generated.
• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils
thickness.
• Sanding should be done in a manner to reduce tracking of paint dust outside the work
area.
Cleaning and Disposal
• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the
duration of the sanding project. Vacuum filter bags should be changed frequently.
• Plastic drop cloths should be gathered up and disposed of along with any dust chips or
other removal debris. They should be placed in sealed refuse receptacles and
disposed of through regular trash pick-up procedures. During clean up, children and
pregnant women should be kept away from the immediate work area.
• All toys, washable furniture and utensils used by children should be washed
thoroughly before being used again.
Introduction
The MS2000 is a complete sanding kit that allows you to choose between 4 different
sanding configurations to do a variety of tasks. Combining the versatility with the Smart
SelectTM feature, the sander gives you optimal results.
Assembly
Warning: Before assembly, make sure that the tool is switched off and
unplugged.
Removing sanding bases - Figure B
• To remove the sanding base, press the
release button (3) and pull the base (6) off
the tool.
B
6
3
6
Random orbit sanding base
With this sanding base, you can use the tool as a random orbit sander.
Attaching the random orbit
sanding base - Figure C
9
C
• Hold the tool and the sanding base (4)
facing upwards as shown in figure C.
• Align the dust openings (9) in the sanding
base with the dust openings (10) in the
tool base.
• Press in on the sanding base until you
hear it click into place.
4
9
10
D
Fitting sanding sheets - Figure D
11
• Hold the tool with the sanding base (4)
facing upwards.
• Place the sanding sheet (11) onto the
sanding base (4) making sure the holes in
the sheet line up with the holes in the base.
Large detail sanding base
With this sanding base, you can use the tool
as a detail sander or a flush sander.
4
E
Attaching the large detail sanding
base - Figures E & F
For detail sanding, the pointed end should
face forward as in figure E.
For sanding large areas, the pointed end
should face to the back as in figure F.
• Attach the sanding base as described
above under “Attaching the random orbit
sanding base”
• Press in on the sanding base until you
hear it click into place.
F
7
Fitting sanding sheets - Figure G
• Detach the two diamond-shaped tips (12)
from the sanding sheet (13).
• Hold the tool with the sanding base facing
upwards.
• Place the sanding sheet (13) onto the
sanding base, making sure that the holes in
the sheet line up with the holes in the base.
The diamond-shaped tip (12) can be reversed
and replaced when worn.
• When the front part of the tip is worn,
detach it from the sheet, reverse it and
press it onto the sanding base again.
• When the whole tip (12) is worn, remove it
from the sanding base and fit a new tip (12).
Tip of the sanding base - Figure H
12
H
When the sanding tip (14) is worn, it can be
reversed as shown in figure H.
• The tip (14) can be removed and reversed.
Finger attachment - Figure I
The finger attachment is used for fine detail
sanding.
• Remove the screw (15).
• Remove the sanding holder tip (7) from the
sanding base.
• Fit the finger attachment (8) onto the
sanding base.
• Fit and tighten the screw (15).
• Fit the appropriate sanding sheet (16) onto
the finger attachment.
I
16
15
Let the tool work at its own pace. Do not
overload.
Warning: Do not cover the ventilation slots
when using the tool. Make sure that the
sanding base is flat on the workpiece.
J
Switching on and off - Figure J
• To switch the tool on, set the on/off switch
(1) to position I.
• To switch the tool off, set the on/off switch to
position O.
8
15
14
8
Operation
13
G
1
7
Smart Select Technology - Figure K
K
4
This sander is fitted with a smart select dial
(2) which depicts various sanding
applications. They are used to select the
proper operating mode for your particular
sanding application.
Step 1: Using the Smart Select dial (2)
choose the application that you are going to
3
perform; detail sanding (3), corner sanding
(4), flush sanding (5), random orbit sanding
(6).
Step 2: Once your application is selected,
the window below (7) will recommend the
2
correct base that should be used and
identifies the corresponding sanding speed
(which is automatically set for you).
Step 3: Snap on the recommended base
(using the picture and color recommendation in window 7).
Setting
5
6
7
SMART SELECT TECHNOLOGY CHART
Application
Recommended Base Base Color Speed Setting
Detail finger
Sanding tight and
(1) Low
Orange
hard to reach areas. attachment
Light, detail sanding.
Sanding areas with
corners.
Paint / Stain removal.
Surface preperation
for painting.
Large detail
base - tip
facing
forward
Blue
(1) Low
Flush
sanding
Sanding doors and base - 90º
edge facing
window frames.
Paint / Stain removal. forward
Blue
(2) High
Sanding large areas. Random
orbit base
Remove the most
Green
(2) High
Flush sanding - up
to the edge.
amount of material
quickly.
Paint / Stain removal.
Surface preperation
for painting.
Note: You can override the speed at anytime by moving the Smart Select dial clockwise
for increased speed.
Automatic brake system (ABS)
This tool has an automatic brake system. When the tool is not on the work surface, this
feature keeps the speed of the disc below the speed of the motor. When the tool is
switched off, the disc will stop very quickly.
Dust Collection
WARNING: Collected sanding dust from sanding surface coatings (polyurethane,
linseed oil, etc.) can self-ignite in sander dust canister or elsewhere and cause fire. To
reduce risk, empty canister frequently and strictly follow sander manual and coating
manufacturer's instructions.
CAUTION: When working on metal surfaces, do not use the dust canister or a vacuum
9
cleaner because sparks are generated. Wear safety glasses and a dust mask. Due to the
danger of fire, do not use your sander to sand magnesium surfaces. Do not use for wet
sanding.
L
Dust canister - Figure L
Attaching and removing:
• Fit the dust canister over the dust extraction
outlet. To remove the canister, pull it out to the
rear and off the outlet.
Emptying:
• Remove canister and shake out debris over a
trash can.
Hints for optimum use
• For user comfort, the tool can be operated with
one hand or two as shown in figure M. Do not
place your hands over the ventilation slots.
• Do not exert too much pressure on the tool.
• Regularly check the condition of the sanding
sheet. Replace when necessary.
• Always sand with the grain of the wood.
• When sanding new layers of paint before
applying another layer, use extra fine grit.
• On very uneven surfaces, or when removing
layers of paint, start with a coarse grit. On other
surfaces, start with a medium grit. In both
cases, gradually change to a fine grit for a
smooth finish.
M
Maintenance
Your tool has been designed to operate over a long period of time with a minimum of
maintenance.
Continuous satisfactory operation depends upon proper tool care and regular cleaning.
• Clear the cooling vents and slots with a clean, dry paint brush.
• Clean the housing with a clean, damp cloth. Do not use solvents.
Accessories
Recommended accessories for use with your tool are available at extra cost from your
local dealer or authorized service center. If you need assistance in locating any
accessory for your tool, please call 1-800-54-HOW-TO (544-6986).
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
TROUBLESHOOTING
Problem
• Unit will not start.
Possible Cause
• Cord not plugged in.
• Circuit fuse is blown.
• Replace circuit fuse.
10
Possible Solution
• Plug tool into a working
outlet.
(If the product repeatedly
causes the circuit fuse to
blow, discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
TROUBLESHOOTING (CON’T.)
Problem
Possible Cause
• Circuit breaker is tripped.
Possible Solution
• Reset circuit breaker.
(If the product repeatedly
causes the circuit
breaker to trip,
discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• Cord or switch is damaged.
• Have cord or switch
replaced at Black
& Decker Service
Center or Authorized
Servicer
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool service. Whether you need technical
advice, repair, or genuine factory replacement parts, contact the Black & Decker location
nearest you. To find your local service location, refer to the yellow page directory under
"Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge
in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailer’s policy for exchanges (usually 30 to 90
days after the sale). Proof of purchase may be required. Please check with the retailer for
their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may
be required. Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory and available on our website
www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center. This
product is not intended for commercial use.
Free warning label replacement: If your warning labels become illegible or are missing,
call 1-800-544-6986 for a free replacement.
Black & Decker (U.S.)
Inc.,
701 E. Joppa Rd.
Towson, MD 21286
U.S.A.
See ‘ToolsElectric’
– Yellow Pages –
for Service &
Sales
11