USER'S MANUAL

Model No. 831.283600

Model

Number

Decal

F-" x

EQUIPMENT

EZ F_ _C.

i S E£"

HELPLINE!

1-800-736-6879

SEARS, ROEBUCK AND CO.,

HOFFMAN ESTATES, IL 60179

www.weslo.com

new products, prizes, fitness tips, and much more!

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS .............................................................

BEFORE YOU BEGIN ...................................................................

ASSEMBLY ...........................................................................

HOW TO OPERATE THE STEPPER ........................................................

MAINTENANCE AND TROUBLESHOOTING ..................................................

CONDITIONING GUIDELINES .............................................................

PART LIST ...........................................................................

EXPLODED DRAWING .................................................................

ORDERING REPLACEMENT PARTS ................................................

FULL 90 DAY WARRANTY .......................................................

10

11

7

8

Back Cover

Back Cover

4

6

2

3 tions before using the stepper,

1. Read all instructions in th s manual before .

aescrmea in this manual.

do not wear loose c!othing tl_at could become

SROeS lur IUUL pfUL_UUII.

: ::

2

BEFORE YOU BEGIN

Congratulations for selecting the new WESLO* ALTA

150 stepper. Stepping is one of the most effective exercises for increasing cardiovascular fitness, building endurance, and toning the body. The ALTA 150 stepper offers a selection of features designed to let you enjoy this healthful exercise in the convenience and privacy of your home.

For your benefit, read this manual carefully before

you use the stepper, If you have questions after reading the manual, please call our toll-free

HELPLiNE at 1-800-736-6879, Monday through

Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number before calling. The model number is 831.283600.

Before reading further, please familiarize yourself with the parts that are labeled in the drawing below.

Handlebar

Console

Adjustment Knob

• Misuseoflhis pr_uct

may resultm senous

injury.

• Read user's manual

and follow all warnings and operatinginstructionspriorto use.

, Do netallow children on or aroundmachine.

• Replacelabelif damaged,illegible,or removed.

Resistance Cylinder

FRONT

Frame Knob

Resistance Collar

Pedal

RIGHT SIDE

REAR

ASSEMBLY

Place all parts of the stepper in a cleared area and remove the packing materials, Do not dispose of the packing

materials until assembly is completed. Note: Some small parts may have been pre-sttached for shipping. If a part is not in the parts hag, check to see if it has been pre-attached.

Assembly requires only the included allen wrench.

1. Raise the Stabilizer Frame (23) and the Frame (29) until they meet. Refer to the inset drawing. Set the

Stabilizer Frame into the saddle on the Frame. Attach the Stabilizer Frame to the Frame with an M8 Curve

Washer (2} and the Frame Knob (36).

2. While holding the Upright (27) near the Frame (29) as shown, connect the Reed Switch Wire (34) to the

Upper Wire (37). Attach the Upright to the Frame with three M8 Curve Washers (2), three M8 Spring

Washers (9), and three M8 x 15ram Screws (3).

2

23

36 2 29

2

34_

4

3. Insert one end of the Handlebar (24) into the bracket on the Frame (29). Center the Handlebar in the bracket and rotate the Handlebar to a comfortable position.

Secure the Handlebar with an M8 x 16mm Flat

Washer (1) and the Adjustment Knob (11).

4. Apply a small amount of soapy water to the Handlebar

(24). Slide a Foam Grip (21) onto each side of the

Handlebar. Insert a Handlebar Endcap (20) into each end of the Handlebar.

4

11

Bracket

"'29

21

5. The Console (25) requires one =AA" battery (not included). An alkaline battery is recommended. To install batteries, turn the console over, remove the battery cover, and insert the battery into the battery clip

(not shown). Make sure that the negative end of the

battery (marked "--") is touching the spring in the

battery clip. Replace the battery cover.

®

_ sI

Battery

Battery over

6. Connect the console wire to the Upper Wire (37). Slide the Console (25) onto the Upright Cap (26). Insert the excess wire into the Upright Cap.

6

Console

25

7.

Make sure that all parts are properly tightened before you use the stepper, After assembly is completed, some extra parts may be left over. Place a mat under the stepper to protect the floor.

5

HOW TO OPERATE THE STEPPER

HOW TO USE THE CONSOLE

HOW TO EXERCISE ON THE STEPPER

Place the stepper on a level surface and place a mat under the stepper. (The stepper features precision hydraulic cylinders. However, there is a possibility of slight oil leakage due to the nature of hydraulic cylinders.)

Hold the handlebars and step onto the pedals. Begin stepping, alternately depressing the right and left pedals with a smooth, continuous motion. Because the pedals move independently of each other, you must maintain a continuous motion or both pedals will sink to the floor. Change the height of your step or the stepping pace until you can comfortably maintain a continuous motion.

As you step, you can exemise your upper leg muscles by keeping your feet flat on the pedals. To focus on your calf muscles, rise on your toes as you step.

Stand erect or lean forward slightly as you exercise.

Always keep your back straight in order to avoid injury.

HOW TO ADJUST THE RESISTANCE

To change the stepping resistance, simply turn the resistance collars on the upper ends of the Resistance

Cylinders (28) (see the inset drawing). The arrows on the Resistance Cylinders and the markings on the

resistance collars show which resistance level has been selected. Make sure that both Resistance

Cylinders are at the same resistance setting.

I

//

I

STRIDES

/MIN

SCAN i lu/

"H_I !7'1

:J.luj

CNT

TIME

CAL

If there is a thin sheet of clear plastic on the console, remove the plastic. To turn on the console, press the

MODE or RESET button or begin stepping.

As you step, the upper half of the display will show the total number of steps you have completed. A mode arrow will point to the letters "CNT."

The lower half of the display will show the elapsed time, the approximate number of calories you have burned, and your stepping speed, changing from one mode to the next every few seconds. One mode arrow will point to the word "SCAN," and a second mode arrow will point to the letters 'q'IME," =CAL," or

"STRIDES/MIN."

To view one mode continuously in the lower half of

the display, press the MODE button until there is a mode arrow pointing to the letters "TIME," "CAL," or

"STPS/MIN" but no mode arrow pointing to the word

=SCAN." To view all three modes again, press the button until there is a mode arrow pointing to the word

"SCAN."

To reset the display, press the RESET button for about two seconds.

If the pedals are not moved and the MODE and

RESET buttons are not pressed for a few seconds, the word "STOP" will appear in the left side of the display. If the pedals are not moved and the buttons are not pressed for a few minutes, the console will turn off.

6

MAINTENANCE AND TROUBLESHOOTING

Inspect and properly tighten all parts of the stepper regularly. To clean the stepper, use a damp cloth and a small amount of mild detergent. Never use abrasives or solvents; keep liquid away from the console.

HOW TO REPLACE THE BAI-I'ERY

If the console does not function properly, or if the display becomes faint, the battery should be replaced.

See assembly step 5 on page 5.

HOW TO ADJUST THE REED SWITCH

If the console still does not function properly, the

Reed Switch (34) should be adjusted.

Hold down the

Left Pedal Leg (40) so that the Magnet (35) is level with the Reed Switch. Loosen the M5 x 10mm Selftapping Screw (13). Slide the Reed Switch (34) in or out slightly. The gap between the Reed Switch and the Magnet should be about 1/8". Make sure that the

Magnet will not hit the Reed Switch when the Left

Pedal Leg is moved. Repeat until the console displays correct feedback. Then, retighten the Screw (13).

7

CONDITIONING GUIDELINES

The following guidelines will help you to plan your exercise program. Remember that proper nutrition and adequate rest are essential for successful results.

EXERCISE INTENSITY

Whether your goal is to burn fat or to strengthen your cardiovascular system, the key to achieving the desired results is to exercise with the proper intensity.

The proper intensity level can be found by using your heart rate as a guide. The chart below shows recommended heart rates for fat buming, maximum fat buming, and cardiovascular (aerobic) exercise.

165 155 145 140 130 125 115

145 138 130 125 118 110 103 _1_

125 120

20 30

115

40

110

50

105

60

95

70

90

80

V

To find the proper heart rate for you, first find your age at the bottom line of the chart (ages are rounded off to the nearest ten years). Next, find the three numbers above your age. The three numbers are your "training zone." The lowest number is the recommended heart

rate for fat burning; the middle number is the recommended heart rate for maximum fat burning; the highest number is the recommended heart rate for aerobic exercise.

Fat Burning

To burn fat effectively, you must exercise at a relatively low intensity level for a sustained period of time.

During the first few minutes of exercise, your body uses easily accessible carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy.

If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest humbet in your training zone as you exercise, For maxi-

mum fat burning, adjust the intensity of your exemise

until your heart rate is near the middle number in your

training zone as you exercise.

Aerobic Exercise

If your goal is to strengthen your cardiovascular system, your exercise must be "aerobic." Aerobic exercise is activity that requires large amounts of oxygen for prolonged periods of time. This increases the demand on the heart to pump blood to the muscles, and on the lungs to oxygenate the blood. For aerobic exercise, adjust the intensity of your exercise until your heart rate is near the highest number in your training zone.

HOW TO MEASURE YOUR HEART RATE

To measure your heart rate, first exercise for at least four minutes. Then, stop exercising and place two fingers on your wrist as shown. Take a sixsecond heartbeat count, and multiply the result by 10 to find your heart rate. For example, it your six-second heartbeat count is 14, your heart rate is 140 beats per minute. (A sixsecond count is used because your heart rate wi, drop rapidly when you stop exercising.)

WORKOUT GUIDELINES

Each workout should include the following three pads:

A warm-up, consisting of 5 to 10 minutes of stretching

and light exercise. A proper warm-up increases your body temperature, heart rate, and circulation in prepa-

ration for exercise.

Training zone exercise, consisting of 20 to 30 minutes of exercising with your heart rate in your training

zone. Note: During the first few weeks of your exer- cise program, do not keep your heart rate in your

training zone for longer than 20 minutes.

A cool-down, with 5 to 10 minutes of stretching, This

will increase the flexibility of your muscles and will help to prevent post-exercise problems.

8

EXERCISE FREQUENCY

To maintain or improve your condition, plan three workouts each week, with at least one day of rest between

workouts. After a few months of regular exercise, you may complete up to five workouts each week, if desired. Remember, the key to success is make exercise a regular and enjoyable part of your everyday life.

SUGGESTED STRETCHES

The correct form for several basic stretches is shown at the right.

Move slowly as you stretch--never bounce.

1. Toe Touch Stretch

Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Hamstrings, back of knees and back.

2. Hamstring Stretch

Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times for each leg. Stretches:

Hamstrings, lower back and groin.

3. Calf/Achilles Stretch

With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back loot flat on the floor Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. Repeat

3 times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.

4. Quadriceps Stretch

With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for each leg. Stretches: Quadriceps and hip muscles.

5. Inner Thigh Stretch

Sit with the soles of your feet together and your knees outward.

Pull your feet toward your groin area as far as possible. Hold for

15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles.

#

9

EXPLODED DRAWING--Model

No. 831.283600 Rogo2A

Key No, Qty.

2

8

6

4

5

6

3

2

7

4

4

2

2

2

1

2

1

10

2

2

2

2

6

7

4

5

1

2

3

8

9

10

15

16

17

18

11

12

13

14

19

20

21

22

Description

M8 x 16ram Flat Washer

M8 Curve Washer

M8 x 15mm Screw

M8 Nylon Nut

M8 x 40mm Bolt

M8 x 68mm Bolt

1/4° x 5/8" Self-tapping Screw

M8 x 38mm Flat Washer

M8 Spring Washer

M8 x 25mm Bolt

Adjustment Knob

M8 x 12mm Flat Washer

M5 x 10ram Self-tapping Screw

Pivot Bushing

Cap

Bump-on

Foot

Pedal

Base Endcap

Handlebar Endcap

Foam Grip

Spacer

Key No. Qty.

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

#

#

1

1

1

1

1

2

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1

Description

Stabilizer Frame

Handlebar

Console

Upright Cap

Upright

Resistance Cylinder

Frame

Right Base

Left Base

Pivot Frame

Pivot Axle

Reed Switch/Wire

Magnet

Frame Knob

Upper Wire

M8 x 25mm Patch Screw

Reed Switch Spacer

Left Pedal Leg

Right Pedal Leg

User's Manual

Allen Wrench

Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts.

10

EXPLODED DRAWING--Model No. 831.283600

21

R0OO2A

22

14

18

14

22

14

32

17

31

14

11

SEARS

Model No. 831.283600

QUESTIONS?

If you find that:

• you need help assembling or

operating the WESLO ®ALTA 150 stepper

• a part is missing

• or you need to schedule repair service call our toll-free HELPLINE

1-800-736-6879

Monday-Saturday, 7 am-7 pm

Central Time (excluding holidays)

REPLACEMENT

PARTS

If parts become worn and need to be replaced, call the following tollfree number

1-800-FON-PART

(1-800-366-7278)

All replacement parts are available for immediate purchase or special order when you visit your nearest SEARS Service

Center. To request service or to order parts by telephone, call the toll-free numbers listed at the left.

When requesting help or service, or ordering parts, please be prepared to provide the following information:

• The MODEL NUMBER of the product (831.283600)

• The NAME of the product (WESLO ®ALTA 150 stepper)

• The KEY NUMBER and DESCRIPTION of the PART (see the

PART LIST and the EXPLODED DRAWING on pages !0 and

11)

[

FULL 90 DAY WARRANTY

For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this

SEARS STEPPER EXERCISER, contact the nearest SEARS Service Center throughout the United

States and SEARS will repair or replace the STEPPER EXERCISER, free of charge.

This warranty does not apply when the STEPPER EXERCISER is used commercially or for rental purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179

]

Part No. 190614 R0902A Printed in China © 2002 Sears, Roebuck and Co.