Whirlpool RF33OOXV User's Manual

CoZoz;ous-Cleaning
RF330PXV (Shown)
RF33OOXV
Contents
Page
BEFORE YOU USE YOUR RANGE
IMPORTANT SAFETY
INSTRUCTIONS. ...............
PARTS AND FEATURES. .........
USING YOUR RANGE. ..........
Using the Surface Units. ......
Home Canning Information.
Setting the Clock ............
Using the Minute Timer. ......
Baking or Roasting ..........
Setting the Oven Controls
How To Position Racks
andPans ...............
Broiling .....................
Setting the Oven Controls . .
Custom Broil ..............
Broiling Tips ...............
Adjusting the Oven
TemperatureControl
......
2
3
5
6
6
8
9
9
10
10
11
12
12
13
13
Page
15
The Oven Vent . . . . . . . . . .
The Storage Drawer . . . . . . . 16
Optional Door Panel Pat . . . 17
CARING FOR YOUR RANGE . . 17
17
Control Panel and Knobs . .
Surface Units and Reflector
Bowls . . . . . . . . . . . . . . . . .
18
Lift-Up Cooktop
.
..
. 20
20
The Oven Door
. ..
.
21
The Oven Window . . . . . . .
The Continuous-Cleaning
22
Oven . . . .
..... ....
Cleaning Chart . . . . . . . . . 24
25
The Oven Light . . . . . . . . . . .
IF YOU NEED SERVICE
OR ASSISTANCE.
. ......... .
WHIRLPOOL RANGE
WARRANTY
....... ....
26
28
14
01990 Whirlpool Corporation
Before you use your range
You are responsible
l
l
l
l
l
l
for:
Reading and following all safety precautions in this Use and Care Guide.
Installing and leveling the range on a floor strong enough to support its
weight, and where it is protected from the elements. (See the Installation
Instructions.)
Making sure the range is not used by anyone unable to operate it properly
Properly maintaining the range.
Using the range only for jobs expected of a home range.
Making sure the range is secured by a properly installed anti-tip bracket,
with a rear leveling leg positioned under bracket.
Remove the Consumer Buy Guide label. It will be easier to remove before the
range is used. To remove any remaining glue:
l Rub briskly with thumb to make a ball, then remove.
or
l Soak area with liquid
hand dishwashing detergent before removing glue
as described above.
Do not use sharp instruments, rubbing alcohol, flammable fluids or abrasive
cleaners. These can damage the finish. See “Important Safety Instructions”
on page 3.
IMPORTANT
SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical
shock, injury
to persons, or damage
when using the range,
follow basic precaullons,
including the followlng:
l
l
Read all instructions before using
the range.
Install or locate the range only in
accordance with the provided
Installation Instructions. It is recommended that the ran e be installed by a qualifie 8 installer. The
ran e must be properly connet 3ed to electrical supply and
gr%nded.
mTo reduce the risk of tipping of the
appliance, the appliance must
be secured by a properly installed anti-tip bracket. To check if
the bracket is installed properly,
remove the storage drawer [see
page16 and verify that the antitip brat 1,et is engaged.
l Do not use the range for warmin
or heating the room. Persons cou 9d
be burned or injured, or a fire
could start.
b Do not leave children alone or
unattended in area where the
range is in use. They should never
be allowed to sit or stand on any
part of the range. They could be
burned or injured.
b Do not wear loose or hanging garments when using the range. They
could ignite if they touch a hot surface unit or heating element and
you could be burned.
b Do not repair or replace any part
of the range unless specifically
recommended in this manual. All
other servicin should be referred
to a qualified 9echnician.
n Do not store flammable materials
in or near the range. They could
explode or burn.
n Do not use water on grease fires.
l
l
l
l
l
l
Never pick up a flaming pan.
Smother flamin pan on cooktop
by covering wit1 a well-fitted lid,
cookie sheet or flat tray. Flaming
grease outside of pan can be
extinguished with baking soda or,
if available, a multipurpose dry
chemical or foam-type
extinguisher.
Use only dry potholders. Moist or
damp potholders on hot surfaces
may result in burns from steam. Do
not let potholder touch hot heating elements. Do not use a towel or
bulky cloth for a potholder. They
could catch on fire.
Select a pan with a flat bottom
that is about the same size as the
surface unit. If pan is smaller than
the surface unit, some of the heating element will be exposed and
may result in the igniting of
clothing or potholders. Correct
pan size also improves cooking
efficiency.
Never leave surface units unattended at high heat settings. A
boil-over could result and cause
smoking and greasy spill-avers
that may ignite.
Make sure the reflector bowls are
in lace during cooking. Cooking
WI-Phout reflector bowls may subject the wirin and components
underneath tRem to damage.
Do not line reflector bowls with
aluminum foil or other liners. Improper installation of these liners
may result in a risk of electric
shock or fire.
Check to be sure glass cooking
utensils are safe for use on the
cooktop. Only certain types of
glass, glass-ceramic, ceramic,
earthenware or other glazed
utensils are suitable for cooktops
without breaking due to the
sudden change in temperature.
continued
on next page
3
l
l
l
l
l
l
l
Turn pan handles inward, but not
over other surface units. This will
help reduce the chance of burns,
igniting of flammable materials,
and spills due to bumping of the
pan.
Do not soak removable heating
elements in water. The element will
be damaged and shock or fire
could result.
Use care when opening oven
door. Let hot air or steam escape
before removing or replacing
food.
Do not heat unopened containers.
They could explode. The hot
contents could cause burns and
container particles could cause
injury.
Keep range vents unobstructed.
Always position oven racks in
desired location while oven is
cool. If rack must be moved while
oven is hot, do not let potholder
contact hot heating element in
oven.
Do not clean door seal. It is essential for a good seal. Care should
be taken not to rub, damage, or
move the seal. Clean only parts
recommended in this Use and
Care Guide.
l
l
l
Do not use oven cleaners. No
commercial oven cleaner or oven
liner protective coating of any
kind should be used in or around
any part of the oven.
Do not store things children might
want above the range. Children
could be burned or Injured while
climbing on it.
Do not touch surface units, areas
near units, heating elements or
interior surfaces of oven. Surface
units and heating elements may
be hot even though they are dark
in color. Areas near surface units
and interior surfaces of an oven
become hot enough to cause
burns. During and after use, do not
touch, or let clothing or other flammable materials contact surface
units, areas near units, heating elements or interior surfaces of oven
until they have had sufficient time
to cool. Other surfaces of the
range may become hot enough
to cause burns; such as, the oven
vent opening, the surface near the
vent opening, the cooktop, the
oven door and window.
. FOR YOUR SAFETY.
DO NOT STORE OR USE GASOLINE
OR OTHER FLAMMABLE VAPORS
AND LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER APPLIANCE.
THE FUMES CAN CREATE A FIRE
HAZARD OR EXPLOSION.
- SAVE THESE INSTRUCTIONS
Thank you for buying a Whlrlpooi
appliance.
mail the Owner Reglstratlon
Card provlded
Please complete
with this product.
and
Then
complete the form below. Have this information ready if you need service
or call with a question.
l
l
Copy model and serial numbers
from plate (behind the oven door
on the oven frame] and purchase
date from sales slip.
Keep this book and the sales slip
together in a handy place.
Model Number
Serial Number
Purchase Date
Service Company
4
Phone Number
Parts and features
Models RF330PXV and RF3300XV
LEFTREAR
CONTROL KNOB
LIGHT
CLOCK/
OVEN TEMPERATURE
MINUTE TIMER CONTROL t
INDICATOR LIGHT
SURFACEUNIT
MARKER
RIGHT FRONT\
CONTROL KNOI
OVEN VENl
CONTROL PANEL
ONE-PIECE CHROME
REFLECTORBOWL
MODEL AND
CONTINUOUSCLEANING OVE
REMOVABLE
STORAGE DRAWER
Using your range
Using the Surface Units
Surface Unit
Indicator lights
One of the surface unit indicator
lights on the control panel will glow
when a surface unit is on.
Control knobs
before tumlng
must be pushed
in
them to a setting. They
can be set anywhere between HI
and OFF.
Surface Unit Markers
The solid dot in the surface unit
marker shows which surface unit
is turned on by that knob.
Burn and Fire Hazard
Be sure all control knobs are
turned to OFF and all indicator
lights are OFF when you are not
cooklng. Someone could be
burned or a fire could start if
a surface unit is accidentally
left ON.
Untti you get used to the settings, use the following
as a guide. For best results,
start cooking at the high settings; then turn the control knob down to continue
cooking. Turn on the surface unit only after placing filled pan on unit.
Use HI to start
foods cooking; to bring
liquids to a
boil.
Use MED-HI
Use MED
Use MED-LO
Use LO to
to hold a
rapid boil; to
fry chicken
or pancakes.
for gravy,
puddings
and icing; to
cook large
amounts of
vegetables.
to keep food
cooking after
starting it
on a higher
setting.
keep food
warm until
ready to
serve. Set the
heat higher
or lower
within the LO
band to keep
food at the
temperature
you want.
Cookware
There is no one brand of utensil that is best for all people. Knowing something
about pan materials and construction will help you select the right cooking
utensils for your needs.
1. Use only
flat-bottomed utensils that make good contact with the surface units.
To check the flatness of a utensil:
Turn it over and check the bottom of the pan by placing a ruler across it.
Rotate the ruler in all directions. There should be no gaps between the pan
and the ruler.
2. The pan should have straight sides and a tight:fitting lid.
3. Choose medium to heavy gauge (thickness) pans that are fairly lightweight.
Remember that a very heavy pan will be even heavier when filled with food.
6
4. The pan material (metal or glass] affects how fast heat transfers from the
surface unit through the pan material and how evenly heat spreads over
the pan bottom.
5. Handles should be made of a sturdy, heat-resistant material and be
securely attached to the pan.
l
l
l
l
l
Burn, Personal InJury and Product Damage
Hazard
It the pan is too small for the surface unit, you could be burned by the
heat from the exposed
section of the surface unit. Use correctly
sized
cooking utensils to prevent InJury.
Not all glass, glass-ceramic,
ceramic,
earthenware
and other glazed
utensils are safe for cooktop
cooking.
Some will crack or break wlth
sudden temperature
changes,
which could result in personal
injury.
If a surface unit stays red for a long time, the bottom of the pan is not
flat enough or Is too small for the surface unlt. Prolonged
usage of
incorrect
utensils for long periods of tlme can result in damage
to the
surface unit, cooktop,
wiring and surroundlng
areas. To prevent
damage,
use correct utensils, start cooking on HI and turn control down
to continue
cooklng.
Do not leave an empty utensil, or one which has boiled dry, on a hot
surface unlt. It can overheat
and may damage
the utensli or surface
unit.
Do not use canners, woks and speclaity
utensils with rounded, warped,
ridged or dented bottoms. These could cause severe overheating
which damages
the utensil and/or surface unlt.
Home Canning Information
To Protect Your Range:
1. Use flat-bottomed canners
for best results. Do not use canners with dented or
ridged (porcelain enamel-ware] bottoms. They do not make good contact
with the surface unit and cause severe over-heating which damages the
cooktop.
2. For best results, use a canner which can be centered over the surface unit.
Large diameter canners, if not properly centered,trap heat and can cause
damage to the cooktop.
3. Do not place canner on two surface units at the same time. Excessive heat
build-up will damage the cooktop.
4. Alternate surface units, This allows the surface units to cool down between
batches.
5. Start with hot water. This reduces the time the control is set on high. Reduce
heat setting to lowest position needed to keep water boiling.
6.
Keep reflector bowls clean for best heat reflection.
7. To prolong the life of the elements:
l Prepare small batches
at a time.
l Do not use elements for canning
all day.
Optional Canning Kii (Part NO.
242905)
The large diameter of most water-bath or pressure canners combined with high
heat settings for long periods of time can shorten the life of regular surface units
and cause damage to the cooktop.
If you plan to use the cooktop for canning, we recommend the installation of a
Canning Kit. Order the kit from your Whirlpool dealer or authorized WhirlpoolSM
service company.
8
Setting the Clock
Push In and turn the Minute
1. Push
In Minute
turn clockwlse
llmer
llmer
Knob to set the Clock.
Knob and
until clock shows
the right time of day.
2. let the Mlnute
llmer
Knob pop
out. Turn clockwise until Minute
Timer hand points to OFF.The
clock sefflng will change It you
push In the knob when tumlng.
Using the Minute Timer
The Minute Timer does not start or stop the oven. It works like a kitchen timer.
Set it in minutes up to an hour. You will hear a buzzer when the set time is up.
DO NOT PUSH IN THE KNOB when setting the Minute Timer.
1. Without
pushlng lt In, turn the
Minute Timer Knob until the timer
hand passes the setting you want.
PUSHING
SEWING.
pushlng In, turn the knob
back to the setting you want.
When the tlme Is up, a buzzer
will sound. To stop the buzzer, turn
the Minute Timer hand to OFF.
2. Without
IN AND TURNING THE MINUTE TIMER KNOB CHANGES
THE CLOCK
9
Baking or Roasting
Setting the Oven Controls
1. Position
the rack(s) properly
before turning on the oven. To
change rack posltlon, lift rack at
front and pull out. For information
on positioning racks, see
“How To Position Racks and Pans”
on page 11.
3. Set the Oven Temperature Control
to the baking temperature you
want. The Oven Indicator Light will
come on. The oven is preheated
when the Oven Indicator Light first
goes off.
NOTE: Do not preheat oven when
roasting or cooking items such as
casseroles.
5. When baking
is done, turn both
the Oven Selector and Oven Temperature Control to OFF
10
2. Set the Oven Selector to BAKE.
4. Put food in the oven. During baking, the elements will turn on and
off to keep the oven temperature
at the setting. The Oven Indicator
Light will turn on and off with the
elements.
The top element helps heat
durlng baklng, but does not
turn red.
How To Position Racks and Pans
The rack(s) should be placed so the top of the food will be centered in the
oven. Always leave at least 1Yzto 2 inches (4-5 cm) between the sides of the
pan and the oven walls and other pans.
For proper
l
l
l
cooklng,
follow
these guldelines
for specific
foods:
Angel and bundt cake pans, yeast breads, frozen pies, large roasts and
turkeys- place rack on lowest level
Casseroles, muffins, most quick breads and meats - place rack on second
level from bottom
Cookies, biscuits, cakes and non-frozen pies - place rack on second or thir
level from bottom
When baking on two racks, arrange racks on bottom and third level from
bottom.
Fire and Personal Injury Hazard
Always posltlon oven racks In deslred location
before turnlng oven on.
Be sure the racks are level.
l If racks
must be moved while oven is hot, use potholders
or oven mitts
to protect hands.
l Do not let potholders
or oven mitts contact
hot heating elements.
l Always
use a dry potholder
or oven mitt to change racks or handle
utensils In the oven. Do not use a damp potholder
or oven mltt. Steam
burns could result.
Fallure to follow the above precautions
may result In fire or personal
InJury.
l
The hot air must circulate around
the pans in the oven for even heat
to reach all parts of the oven.
For Besf Alr Clrculalfon:
Place the pans so that one is not
directly over the other.
l Allow lYz-2 inches (4-5 cm) of space
around each pan and between
pans and oven walls.
l Use only one cookie
sheet in the
oven at one time.
Use the following as a guide to
determine where to place the pans.
l
One Pan
Place in the center of the oven rack.
Two Pans
Place in opposite corners of the
oven rack.
NOTE: “Oven peeking” may cause
heat loss, longer cooking times and
unsatisfactory baking or roasting
results. Rely on your timer.
Broiling
Setting the Oven Controls
1. Position
the rack properly before
turning on the oven. The oven rack
should be positioned so that the
surface of the food is at least 3
inches (7.4 cm] away from the
broil element.
12
2. Put the broiler pan and food on
the rack.
3. Close the door to the Broil Stop
position (open about 4 inches,
10.2 cm). The door will stay open
by itself.
NOTE: The door must be partly
open whenever the oven is set to
BROIL.Leaving the door open
allows the oven to maintain
proper temperatures.
4. Set the Oven Selector and Oven
Temperature Control to BROIL.
NOTE: Do not preheat oven when
broiling.
5. When broiling is done, turn both
the Oven Selector and Oven
Temperature Control to OFF.
Custom Broil
l
If food is cooking too fast, turn the Oven Temperature Control counteruntil the Oven Indicator Light goes off.
If YOU Want the food to broil slower from the start, set the Oven Temperature
Control between 150” and 325°F (65.5” and 162.7”C). The lower the temperature, the slower the cooking.
clockwise
l
The Oven Selector
must be on BROIL for all broiling
temperatures.
Broiling Tips
l
l
l
Use the broiler pan and grid for broiling. They are designed to drain excess
liquid and fat away from the cooking surface to help prevent spatter, smoke
or fire.
Refer to a broiling chart in a reliable cookbook for correct broiling times.
After broiling, remove the broiler pan from the oven when you remove the
food. Drippings will bake on the pan if it is left in the heated oven.
Flre Hazard
) Place meat the correct distance
from the element. Meat placed too
close to the element may spatter, smoke, burn or catch flre during
brolllng.
1 To ensure adequate
grease dralnage,
do not use cookie sheets or
simllar pans for brolllng. Also, covering the broiler grld wlth foil Is not
recommended.
Poor dralnage
of grease may result in fire. If foil is
used, cut sltts in toll to correspond
wlth all openings
In broiler grid.
Grease can then draln away and cool In pan.
Adjusting the Oven Temperature Control
Does your oven seem hotter or colder than your old oven? The temperature of
your old oven may have shifted gradually without your noticing the change.
Your new oven is properly adjusted to provide accurate temperatures. But
when compared to your old oven, the new design may give you different
results.
If after using the oven for a period of time, you are not satisfied with the temperature settings, they can be adjusted by following these steps:
LOCKING
1. Pull the
Oven Temperature Control
Knob straight off.
2. Loosen the locking screws inside
the control knob. Note the posltlon of the notches.
TOOTN
NOTCHES
move
the tooth a notch closer to LO.
Each notch equals about 10°F
(5°C).
3. To lower the temperahtre,
TooTn
move
the tooth a notch closer to HI. Each
notch equals about 10°F[SOC).
lighten the locking sorews and
4. To ralse the temperature,
replace
14
NOTCHES
the control
knob.
The Oven Vent
Hot air and moisture escape fTom the
oven through a vent under the right
rear surface unit. You can cook on the
unit, or keep food warm on it while
the oven is on.
Burn Hazard
If you leave a utensil on the rlght
rear rurlace unit, use potholders
when removlng
lt. Pan handles
can become
hot enough to burn.
Plastic utensils leff over the vent
can melt.
The vent is needed for air circulation
Do not block the vent. Poor baking
can result.
The Storage Drawer
The storage drawer is for storing pots and pans. The drawer can be removed
to make it easier to clean under the range, and to check for installation of the
anti-tip bracket.
Use care
when handllng
the drawer.
Removing the storage drawer
1. Empty drawer
of any pots and
pans.before removing drawer. Pull
drawer straight out to the first stop.
Lift front and pull out to the second
stop.
Replacing
2. Lift back slightly and slide drawer
all the way-out.
the storage drawer
:I!
-KY-
1.
Fit ends of drawer sliz rails into
the drawer guides on both sides
of opening.
2. Lift drawer froxnd
push in until
metal stops on drawer slide
rails clear white stops on drawer
guides. Lift drawer front again
to clear second stop and slide
drawer closed.
To verity the an&tip
Is engaged:
Remove the storage drawer.
Look to see if the anti-tip bracket
is attached to floor with screws.
l Make sure one rear leveling
leg
is positioned under the anti-tip
bracket.
0 See Installation Instructions for
further details.
l
l
16
brucket
Optional Door Panel Pat
(Model RF33OPXV)
If you would like to change the color of your oven door glass to white or
almond, you can order one of these kits: White (Kit No. 814069) or Almond
[Kit No. 814070) from your Whirlpool Dealer. The kits include easy installation
instructions,
Caring for your range
Control Panel and Knobs
I
Burn and Electrical
Shock Hazard
Make sure all controls are OFF and the range
Is cool before cleaning.
Fallure to do so can
result In burns or electrlcal
shock.
1. Turn control
knobs to the OFF position.
2. Pull control knobs straight off.
3. Use warm soapy water or spray glass cleaner, and a soft cloth, to wipe the
control panel. Rinse and wipe dry.
4. Wash control knobs in warm soapy water. Rinse well and dry. Do not soak.
5. Replace control knobs by pushing them firmly into place.
NOTE: When cleaning, never use steel wool, abrasives, or commercial oven
cleaners which may damage the finish. After cleaning, make sure all control
knobs point to the OFF position.
Reflector Bowls
Burn and Electrlcal
Shock Hazard
Make sure all surface units are OFF before
removlng surface unlts and reflector bowls.
Failure to do so can result In burns or
elect&al
shock.
‘I. Turn off all surface units.
2. Lift the edge of the unit, opposite
the receptacle, just enough to
clear the element hold down clip
and the reflector bowl.
3. Pull the surface unit straight away
from the receptacle.
4.
Lifl out the reflector bowl. See
“Cleaning Chart” on page 24 for
cleaning instructions.
continued
18
on next page
Replacing
l
l
1.
Burn, Electrlcal
Shock and Fire Hazard
Make sure all surface unlts are OFF before replacing
surface units and
reflector bowls. Failure to do so can result in burns or electrical
shock.
Do not line the reflector bowls wlth foil. Fire or electrical
shock
could result.
Turn off ail surface units.
1.Hold the surface unit as level as
possible with the terminal just
started into the receptacle. Push
the surface unit terminal into the
receptacle.
Line up openings in the reflector
bowl with the surface unit receptacle and the element hold down
clip.
#.When terminal is pushed into the
receptacle as far as it will go, push
down the edge of the surface unit
opposite the receptacle. The element hold down clip will keep the
surface unit from moving around.
NOTE: Reflector bowls reflect heat back to the utensils on the surface
unlts. They also help catch spills. When they are kept clean, they reflect
heat better and look new longer.
If a reflector
bowl gets dlscolored,
some of the utensils may not be flat
enough, or some may be too large for the surface unit. In either case,
some of the heat that’s meant to go Into or around a utensil goes down
and heats the reflector bowl. This extra heat can discolor it.
Lift-Up Cooktop
1. Lift front of cookto~
at both front
corners until the support rods lock
into place.
l
l
Personal lnlury and Product
Damage
Hazard
Be sure both support rods are
fully extended
and in the
locked posltlon. Failure to do
so could result In personal
Injuw from the cooktop
accldentally
falling.
Do not drop the cooktop.
Damage
can resutt to the porcelain and the cooktop
frame.
2. Wipe with warm, soapy water.
Use a soapy steel wool pad on
heavily-soiled areas.
3. To lower the cooktop; lift cook-top
from both sides while pressing the
support rods back to unlock them.
Lower the cooktop into place.
The Oven Door
Removing the oven door will help make it easier to clean the oven.
Burn and Electrical
Shock Hazard
Make sure all controls are OFF and the oven
is cool before removing
oven door. Failure to
do so can result in burns or electrical
shock.
1. Open
the door to the first stop
position.
2. Hold the door at both sides and lift
lt at the same
angle
lt Is in.
fit the bottom corners
of the door over the ends of the
hinges.
Push the door down evenly. The
door will close only when it is on
the hinges correctly.
3. To replace,
20
The Oven Window
If your range has an oven window instead of the black glass door,the outer glas
and frame can be removed for cleaning. DO NOT TAKE APART A BLACK 6LASS
DOOR.
To remove the outer window:
c
Burn and Electrical
Shock Hazard
Make sure all controls are OFF and the oven Is
cool before removing the outer window. Fallure
to do so can result In burns or electrical
shock.
1. Turn off all
controls. With the door
closed, remove the screws from
the top of the outer window frame.
2. Slightly tip the window and
frame out from the top.
3. Wt~sb$~~~r;ds,~~ft up on both
To replace the outer window:
Fit the bottom tabs of the frame
into the bottom of the window
opening.
2. Push the top of the frame into
place while pushing down.
3. Replace the screws.
The Continuous-Cleaning Oven
Standard oven walls are coated with smooth porcelain, Your ContinuousCleaning oven walls are coated with a special, rougher porcelain. A fat
spatter beads up on the smooth surface, but spreads out on the rougher
surface. The bead of fat on the smooth surface chars and turns black. The
spread-out fat on the rough surface gradually
burns away at medium to
hlgh baking temperatures
so the oven can return to a presentably clean
condition.
Using Foil
Using foil on the oven bottom is recommended to catch sugar and starchy
spills from pies and casseroles. It must be used properly. Cut foil from a roll of
heavy-duty la-inch (45 cm) aluminum foil, or buy a foil kit (Par-l No. 241430)
fromyour Whirlpool Appliance dealer.
I
l
l
Burn, Electrical
Shock and Product Damage
Hazard
Make sure all controls are OFF and the oven Is cool betore using foil.
Failure to do so can result In burns or electrical
shock.
Do not let foil touch the bake element. It could damage
the element.
Make sure foil Is flat on the bottom and away from the bake element.
1. Turn off all
controls,
2. Lift the Cool bake element slightly
to Ilft the teet off the oven
bottom.
3. Slide the foil under the bake
element. Make sure the foil is cen-
fered and long enough to start up
both side oven walls without wrinkling. For proper baking, lower
the bake element so all feet rest
solldly on the toll.
22
Cleaning
Tips
1. The oven
window al ?d racks are ntot coated. C
2. The oven door does not get as hot as the walls.
needed.
3. If you do more broiling than baking, hand cleaning
4. Use aluminum foil on the oven bottom according
may not burn away and could stain the bottom.
may be needed.
to instructions. Spill-overs
Hand Cleaning
Personal Injury Hazard
Do not use oven cleaning
products. Some can become trapped in the porcelain
surface
and give off harmful tumes.
RACKS - Use a soapy steel wool
pad for best cleaning results. Rinse
well.
WINDOW-Keep
clean with hot
soapy water. Use a plastic scrubbing pad for heavily-soiled areas.
Rinse well. Do not use steel wool or
abrasive
cleansers.
WALLS AND DOOR -Wash with hot
soapy water. Use a steel wool pad o
plastic scrubbing pad for heavilysoiled areas. Rinse well.
Cleaning Chart
PART
EXiMi0t
suttaces
(potcelaln
and chrome
flnlsh)
(chrome
flnlsh)
Surface unlfs
WHAT TO USE
Warm soapy water and
a soft cloth.
Non-abrasive plastic
scrubbing pad for heavilysolled areas.
. Wipe off regularly when range is
COOI.
. Do not allow tood confalnlng
acids (such as vlnegat, tomato,
lemon Juice or milk) to temaln
on sutface. Acids may remove
the glossy flnlsh.
l Do not use abtaslve
or hatsh
cleansers.
. Make sure cooktop Is COOL.
Chrome cleaner or
pollshing creme.
. Follow directions provided with
cleaner or polishing creme.
NOTE: Pot chrome sutfaces, follow above oleanlng lnsftucflons
before uslng non-abtaslve ohtome cleaner or Cook Top Pollshlng
Cteme (Pat-t No. Sl4009). To obtaln order lnfotmatlon for Cook Top
Pollshlng Cteme, wtlfe to: Whltlpool Cotpotaflon, Affenflon:
Customer Setvlce Dent.. 1900 WhltlDool Dtlve. LaPotte. IN 46305.
. Spatters or spills will burn off.
No cleaning required.
l Do not lmmetse
In water.
Chrome
reflector
bowls
Warm soapy water and
a non-abrasive plastic
scrubbing pad.
Control knobs
Warm soapy water and
a soft cloth.
Control panel
Warm soapy water or
spray glass cleaner
and a soft cloth.
Btollet pan
and gtid
Warm soapy water or a
soapy steel wool pad.
Oven tacks
Warm soapy water or
soapy steel wool pads.
Oven door
glass
Spray glass cleaner or
warm soapy water and
a non-abrasive plastic
scrubbing pad.
ConflnuousCleaning Oven
Warm soapy water or a
soapy Steel WOOI pad.
Heavy-duty
24
HOW TO CLEAN
aluminum foil.
. Wash, rinse and dry well.
l Clean
frequently.
. Do not use abtaslve or harsh
cleansets.
Wash, rinse and dry well.
9 Do not soak.
l
l
l
l
l
l
l
l
l
Wash, rinse and dry well.
Follow directions provided
the cleaner.
with
Clean affet each use.
Wash, rinse and dry well.
Wash, rinse and dry. Use soapy steel
wool pads for heavily-soiled areas.
Make sure oven is cool.
Follow directions provided
the cleaner.
Wash, rinse and dry well.
with
Remove door for easier access.
Clean heavily-solled areas or
stains. Rlnse well with water.
. Place piece of foil on oven floor to
catch spillovers. Make sure the foil Is
centered and long enough to start
up both side oven walls without
wrinkling.
l
Do not use commercial oven
cleanets.
l
Mod fat splatten on oven walls
and floor will gradually teduoe to
a presentably clean condlfion
dutlng baklng.
l
l
The Oven Light
The oven light will come on when you push the Oven Light Switch on the
control panel. Push it again to turn off the light.
To replace:
l
l
Electrical
Shock and Personal InJury Hazard
Make sure oven and light bulb are cool and powerto
the range has
been turned OFF before replaclng
the light bulb. Failure to do so could
result In electrlcal
shock or burns.
The bulb cover must be In place when uslng the oven. The cover
protects the bulb from breaking, and from hlgh oven temperatures.
Since bulb cover Is made of glass, be careful not to drop lt. Broken
glass could cause InJury.
1. Unplug
2. Remove the glass bulb cover in
the back of the oven by screwing
it out counterclockwise.
3. Remove the light bulb from its
socket. Replace the bulb with a
40-watt appliance bulb.
4. Replace the . bulb cover by
screwing it in clockv
appliance or reconl nect at the
mrrin
wed\,r
I I lull I rm\rmr
tJ”..Fil El
*uppa
appliance or disconnect
at the main power supply.
If you need service or assistance,
we suggest you follow these steps:
If cooking
results aren’t what
1. Before caUing for
expected:
assistance...
l
Performance problems often result
from little things you can find and fix
without tools of any kind.
If nothlng
l
l
operates:
Is the power supply cord plugged
into a live circuit with the proper voltage? (See Installation Instructions.)
Have you checked
your home’s
main fuses or circuit breaker box?
l
l
l
l
l
If the oven will not operate:
Is the Oven Selector turned to a Setting (BAKE or BROIL)?
l Is the Oven
Temperature Control
turned to a temperature setting?
It surface units will not operate:
l Have
you checked
your home’s
main fuses or circuit breaker box?
l Are surface units plugged
in all the
way?
l Do the control
knobs turn?
l
If surface
not turn:
l
unlt control
knob(s)
will
Did you push in before trying to turn?
If soil is visible on ContlnuousCleaning
oven flnlsh:
l
The special
finish is designed to
oven soil during
normal baking or roasting. It is not
designed to keep your oven spotless, only presentably clean.
If you broil often, you may see oven
soil.
The door is cooler than the oven
walls. Soil will be more visible on the
door than other areas in the oven.
See page 23 for how to clean.
Sugar and starchy spills may leave
stains. See page 23 for hand cleaning tips. Keep foil on oven bottom to
gradually
l
l
l
catch
reduce
these
spills.
l
l
you
Is the range level?
Does the oven temperature seem
too low or too high? See page 14.
If needed, have you preheated the
oven as the recipe calls fofl
Are you following a tested recipe
from a reliable source?
Are you using pans recommended
in the “Cookware”
section on
page 6?
If baking, have you allowed lY2 to 2
inches (4-5 cm) on all sides of the
pans for air circulation?
Are the pans the size called for in the
recipe?
Do the cooking
utensils have
smooth, flat bottoms and fit the surface elements being used?
2.
If you need
assistance%.
Call Whirlpool
COOL-LINE@ service assistance
telephone
number.
Dial free from anywhere
in the U.S.:
1-800-253-1301
and talk with one of our trained consultants. The consultant can instruct
you in how to obtain satisfactory operation from your appliance or, if service is necessary,
recommend
a
qualified service company in your
area.
If you prefer, write to:
Mr. Donald Skinner
Director of Consumer Relations
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
Please include a daytime phone
number in your correspondence.
CDntinUed
on next page
3.
5
If you need service%.
&q
g
Whirlpool
has a
nationwide
net()l’” yz;,: &$p;;
SERV’CE
service combanies. Whirlpool
service technicians
are trained to
fulfill the product warranty and provide after-warranty
service, anywhere in the United States. To locate
the authorized
Whirlpool
service
company
in your area, call our
CCCL-LINE@ service assistance telephone number (see Step 2) or look in
your telephone
directory
Yellow
Pages under:
0
l
l
l
4.
If you need FSP”
replacement parts?..
FSP is a registered trademark of
Whirlpool Corporation
for quality
parts. Look for this symbol of quality
whenever you need a replacement
part for your Whirlpool appliance. FSP
replacement
parts will fit right and
work right, because they are made to
the same exacting
specifications
used to build every new Whirlpool
appliance.
If you are not satisfied
with how the problem
was solved 3:..
Contact the Major Appliance Consumer Action
Panel (MACAP).
MACAP is a group of independent
consumer experts that voices consumer views at the highest levels of
the major appliance industry
Contact MACAP only when the
dealer, authorized
servicer
or
Whirlpool have failed to resolve
your problem.
Major Appliance Consumer
Action Panel
20 North Wacker Drive
Chicago, IL 60606
MACAP will in turn inform us of your
action.
*When requesting assistance, please
provide:
model number, serial
number, date of purchase, and a
complete description of the problem. This information is needed in
order to better respond to your
request.
To locate FSPreplacement parts in
yourarea, referto Step 2 above or call
the Whirlpool COOL-LINE service assistance number in Step 3.
27
WHIRLPOOL’
RANGE PRODUCT
W-TY
1 UWOYH OF WARRAMY
nu cm-me
WARRANTY
From Date of Purchase
WI-
hbWlikl
EROOl
WIU PAY FCR
FSP replacement parts and repair labor to
correct defects In materials or workmanshlp.
Servlce must be provided by an authorized
WhlrlpoollH sewlce comoanv.
WILL WY PAY FOR
A. Service calls to:
1. Correct the lnstallatlon of the range product.
you how to use the range product.
2. InStnCt
3. Replace house fuses or correct house wiring or plumbing.
4. Replace owner accessible light bulbs.
B. Repalrs when range product is used in other than normal, single-family
household use.
C. Pick up and delivery. This product is designed to be repaired in the
home.
D. Damage to range product caused by accident, misuse, fire, flood, acts
of God or use of products not approved by Whirlpool.
WHIRLPOOLCORPORATION SHALL NOT BELIABLEFOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow the exclusion or limitation of incidental or
ConsequentIal damages so this limitation or exclusion may not apply to you. Thls
Worronty
glves you specific legal rights, and you may also have other rlghts
which vary from state to state.
Outslde the Unlted States, a different warranty may apply. For details, please
COntaCt
your franchised Whlrlpool distributor or military exchange.
If YOUneed service, first see the “Service and Assistance” section of this book.
After checking “Service and Assistance:’ additional helo can be found by calling
our CCCL-LINE” service assistance telephone number,+800-253-1301,
from
anywhere in the US.
8 Registered TrademarkEM
Part No. 3150568
01990 Whirlpool Corporation
! Makers
Dishwashers.
Eulll-In
Service Mark of Whirlpool Corporation
Ovens and Surlace Unils. Ranges. Mwowave
Printed in U.S.A.
Ovens Trash Compaclors
Room AH Condll~aners
Oehumldlllen
Aulomallc