basketball hoop - Vuly Trampolines

W W W . V U LY T R A M P O L I N E S . C O M
BASKETBALL HOOP ASSEMBLY | Maintenance Manual
8 Ft. | 10 Ft. | 12 Ft. | 14 Ft. | Vuly Trampolines
READ THIS ENTIRE MANUAL BEFORE ASSEMBLING AND USING VULY PRODUCTS.
THESE PRODUCTS ARE FOR PERSONAL USE ONLY BY PERSONS AGED 6 YEARS AND OLDER
NOT RECOMMENDED FOR CHILDREN UNDER 6 YEARS OF AGE | USE OFFICIAL VULY BASKETBALL ONLY
PLEASE DO NOT HANG FROM OR JUMP INTO BASKETBALL HOOP, ONLY TO BE USED WITH EXTREME CAUTION!
BASKETBALL HOOP | Assembly Instructions
STEP
01
Unpack the components from your basketball
hoop box. Your box should contain:
BASKETBALL HOOP
PARTS LIST
1x Pre-assembled Hoop and Backboard with frame
1x Basketball
1x Basketball pump with needle (in handle)
1x Upper support pole
1x Lower support pole (with rectangular bracket)
2x Net pole elastics (slightly longer)
4x Bolts
4x Nuts
4x Round ended nuts
1x Spanner
1x Screwdriver
3x Long foams
2x Short foams (8ft and 10ft only requires 1x)
PAGE
2
STEP
02
Push in net pole
spring button to
remove a net pole
from your
trampoline.
STEP
STEP
04
Lift up the safety pads where
you removed the safety net
pole from. Push the lower
support pole through the
safety pads hole.
STEP
05
Insert the lower net pole into the lower
support pole.
Note: Rotate until the holes match.
03
Remove the elastic
ties, covers, and
foams from the
net pole using the
spanner. Separate
the upper net pole
and the lower net
pole.
PAGE
3
STEP
06
Using the screwdriver, insert the screw back into the net pole through the
rectangular bracket and t-join to hold the lower net pole in position. Put
each bolt through the square holes in the bracket from the outside so the
bolt heads face towards you. Make sure the bolts go through both sides of
the bracket before attaching the nuts onto the end of each bolt. Tighten the
nuts evenly to avoid bending the bracket. If you tighten each bolt all the way
before tightening the others, you may bend the bracket.
Note: The round holes on the rectangular bracket that house the net
pole screw and spring button must be facing outwards.
STEP
07
Add a long
foam and cover
over the lower
support pole.
PAGE
4
For 12, 14ft ONLY
Also add a short foam piece
before attaching the elastic
tie.
STEP
08
Insert the slightly
longer elastic tie in
the hole above the
foam, ensuring elastic
loop is facing inwards,
towards the net.
STEP
09
Join the upper support pole
to the lower support pole.
Note: Rotate until the holes
match.
STEP
10
Attach the upper
net pole. Insert your
existing top foam
and cover from your
net pole into the
completed net pole.
STEP
12
Add a short foam and a cover.
STEP
13
Add a long foam and a cover.
STEP
11
Insert the elastic tie in the top
hole.
PAGE
5
STEP
14
With the backboard face down, lift up the
frame until it clicks into position.
STEP
15
Remove the black plastic
cap at the top of the safety
net pole. Insert the basktball hoop on top of the net
pole. Put the elastic tie bolt
through the net pole and
the basketball hoop pole.
Using the spanner, tighten
the nut onto the elastic tie
bolt and then re-attach the
net to your elastic ties.
PAGE
6
Congratulations! You have finished assembling your
Vuly Basketball Hoop.
W W W . V U LY T R A M P O L I N E S . C O M
Australia |
1300 - 667- 514
USA |
1 - 877- 538 - 8018
VULY TRAMPOLINES |ۆ‚Û@f_d]klgfÛIgY\ÛÝÛNYc]jd]q•ÛHC;ہ~‚•Û8mkljYdaY
kYd]k³nmdqljYehgdaf]k[geÛÝÛooonmdqljYehgdaf]k[ge