advertisement
XEROX XR3-Series User's Guide Cover
290.00 mm
145.00 mm
User ' s Guide
XR3 Series
LCD Monitor
AS DRAWING
1 1
PANTONE Process Black CV PANTONE Red 032 CV
(inch)
290(W)X210(H)TOL:0~+20
1.2
2005/08/29
©2005 by Xerox Corporation. All rights reserved.
Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen displays, looks, etc.
XEROX® and all Xerox product names mentioned in this publication are trademarks of XEROX CORPORATION. Other company trademarks are also acknowledged.
Changes are periodically made to this document. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions.
Table of Contents
CE Marking Declaration Of Conformity .................................................4
Federal Communications Commission (FCC) Statement ....................5
Important Safety Instructions .................................................................6
Features ........................................................................................................9
Connecting Your LCD Monitor to a Computer ............................................12
Method : Analog (D-SUB) Connection ....................................................12
Installing Your LCD Monitor .........................................................................14
D-SUB Connector PIN Assignment .............................................................22
Authorized Service Centers .........................................................................26
2 Xerox© LCD Monitor User’s Manual
Recycling Place
EUROPE
When disposing of Proview products in Europe, please contact one of the following three locations to make arrangements for recycling.
Proview International (UK) Limited
30 The Avenue, Watford, Hertfordshire
WD17 4AE United Kingdom
Tel: +44 1923-248-111
Fax: +44 1923-248-222
Timothy Lo
Courriel: [email protected]
PGL Europe B.V. (Proview Group Limited Rotterdam)
Satijnbloem 37,
3068 JP
Rotterdam
Hollande
Tel: +31-10-238-1090
Fax: +31-10-238-1091
David Hsieh
Courriel: [email protected]
Xoal bvba
Raketstraat 100-B1130
Bruessels
Mr. Leo Starckx
Tel: +32-2-702-6011
Fax: +32-2-725-2513
Email: [email protected]
ASIA
When disposing of Proview products in Asia, please contact the following location to make arrangements for recycling.
Proview Technology (ShenZhen) Co., Ltd.
North Block 21, 23# Shatoukok Free Trade Zone, ShenZhen, China.
Mr. Dennis Chang
Tel: +86-755-2526-1512
Fax: +86-755-2526-1565
Email:[email protected]
AMERICA
When disposing of Proview products in America, please call the following location to make arrangements for recycling.
Proview Technology, Inc. (U.S.A.)
7373 Hunt Avenue, Garden Grove, CA 92841 U.S.A.
Tel:714-799-3865
Fax:714-379-6290
Patrick Yen
Email:[email protected]
“THIS DISPLAY UNIT IS AN ELECTRIC DEVICE WHICH MAY CONTAIN HAZARDOUS MATERIALS
AND COMPONENTS, AND WHICH MUST BE DISPOSED OF AT END OF LIFE ACCORDING TO
THE PROPER PROCEDURE”
Xerox© LCD Monitor User’s Manual 3
FCC/CE
CE Marking
Declaration Of Conformity
This LCD monitor complies with the requirements of the EC
Directive 89/336/EEC “EMC Directive” and 73/23/EEC “Low
Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
All places of operation are characterized by their connection to the public low voltage power supply system.
4 Xerox© LCD Monitor User’s Manual
FCC/CE
Federal Communications
Commission (FCC) Statement
This equipment has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment
and receiver.
3. Connect the equipment into an outlet on a circuit which is different from what the receiver is connected to.
4. Consult the dealer or an experienced radio/TV technician
for help.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user authority to operate the equipment.
Xerox© LCD Monitor User’s Manual 5
6
Important Safety Instructions
Important Safety Instructions
To prevent any injuries, the following safety precautions should be observed in the installation, use, servicing and maintenance of this equipment.
Before operating this equipment, please read this manual completely, and keep it nearby for future reference.
Warnings
• Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc. The equipment may fall, causing serious injury to children or adults and serious damage to the equipment itself.
• Use only a cart or stand recommended by the manufacturer.
This equipment and recommended cart or stand should be handled with care. Quick stops, excessive force, and uneven surfaces may cause the equipment and cart/stand to overturn.
• Do not disable the 3-wire grounding type plug. The grounding pin on the 3-prong plug is an important feature.
Removing the grounding pin will increase the risk of damaging the equipment. If you can not fit the plug into the electrical outlet, contact an electrician to install a grounding outlet.
• Always operate this equipment from the type of power source indicated on the rear of the serial/model plate.
• Never overload wall outlets and extensions.
• Use and handle the power cord with care.
• Do not place any heavy objects on the AC power cord.
• Do not pull the AC power cord. Do not handle the AC power cord with a wet hand.
Xerox© LCD Monitor User’s Manual
Important Safety Instructions
• Do not touch the power cord and antenna cable during lightning.
• Remove the plug from the wall outlet if the equipment will not be used for a long period of time.
• Do not place, use or handle this equipment near water.
• Never expose the equipment to liquid, rain, or moisture.
Seek qualified service if any of the above is spilled into the equipment.
• Do not attempt to service the equipment yourself.
• Opening and removing the covers may expose you to dangerous voltage or other hazards and may void your warranty. Refer service to qualified personnel.
• Always remove the power cord from the outlet before cleaning the equipment.
• Never use liquid or aerosol cleaners on the equipment.
Clean only with a soft dry cloth.
• Do not expose the equipment to extreme temperature or to direct sunlight, as the equipment may heat up and suffer damage.
• Do not install the equipment near any heat sources such as radiators, heat registers, stoves, or any other apparatus that might produce heat.
• Do not block any ventilating openings. Leave an open space around the equipment.
• Never place the equipment :on a bed, sofa, rug, or any other similar surfaces; too close to drapes/curtains/walls, in a bookcase, built-in cabinet, or any other similar places that may cause poor ventilation.
Xerox© LCD Monitor User’s Manual
(continued on next page)
7
Important Safety Instructions
• If any of the following conditions occur, unplug the power cord from the outlet and request service from qualified personnel.
a. The power cord or plug is damaged.
b. Liquid is spilled into the product .
c. An object falls onto or into the product.
d. The product has been dropped or damaged.
e. The product’s display is abnormal.
8
DISPOSAL OF WASTE ELECTRONIC EQUIPMENT BY PRIVATE
HOUSEHOLDS WITHIN THE EUROPEAN UNION
This sign indicates that this product may not be disposed of with your regular household waste. The recycling and separate collection of such products is your responsibility. Please drop off the above-mentioned waste at a designated place for recycling waste electrical and electronic equipment. If you do not know where to drop off your waste equipment for recycling, please contact your local city office or household waste collection service.
Xerox© LCD Monitor User’s Manual
Introduction
1 Introduction
Features
• Rapid Video Response
Fast action media such as gaming, DVD and video conferencing will playback smoothly thanks to the rapid video response time of the LCD panel.
• High Contrast Ratio
Colors will appear vibrant and lifelike producing superior image quality.
• Plug-and-Play Capability
Easy trouble-free configuration and set-up.
• Anti-Reflective Coating
Special surface treatment on the LCD panel for high ambient light environments that provides excellent legibility by reducing glare.
• Wall-Mounting Capability
Compatible with the VESA industry standard for wall/arm mounts to save valuable desktop space.
Xerox© LCD Monitor User’s Manual 9
Introduction
Package Contents
Make sure all of the following contents are included in the box.
If any items are missing, please return this product to the original place of purchase.
LCD Monitor
Quick
Guide
Warranty
Card
CD-ROM
(Driver/Manual)
AC
Power Cord
10
CAUTION:
Be sure to save original box and all packing material for future transport of monitor.
Xerox© LCD Monitor User’s Manual
Front View and Controls
Introduction
1
2
1 ▼▲ menu.
In OSD mode, press the ▲/▼ buttons to select the desired
2 MENU
Press once to display the OSD (On Screen Display). And press again to activate the desired setting.
3 LED
The LED light indicates when the LCD monitor is activated
(green light indicates power on and amber light indicates power saving).
4
Turns the LCD monitor on and off.
5 AUTO
Press to automatically adjust the display settings to optimize performance based on the D-SUB signal.
Xerox© LCD Monitor User’s Manual 11
3
4
5
Installation
2 Installation
Refer to the owner’s manual of the computer for connections.
In the process of connecting external equipment, do not connect any AC power cords to wall outlets until all other connections are completed.
Connecting Your LCD Monitor to a Computer
Method : Analog (D-SUB) Connection
1
Turn off the computer and unplug the power cable.
2
Connect the signal cable to the D-SUB port on the back of the computer.
3
Connect the power cord to the LCD monitor and wall outlet.
12
2
Connect to the D-SUB port
3 Connect to power source
Xerox© LCD Monitor User’s Manual
Installation
4
Press the button, located on the bottom side of the main unit to turn the monitor on, then turn the computer on. If the monitor displays an image, the monitor is successfully installed. If no image is displayed, check all connections.
NOTE:
Unplug the monitor before installation to avoid electric shock or damage.
NOTE:
The button is used for switching the LCD monitor on and off, it does not disconnect the device from the main voltage.
To completely disconnect the main voltage, please remove the power plug from the socket.
NOTE:
The LED indicator is green when the monitor operates normally and will turn to amber when in power saving mode. When the monitor is off, the LED turns dark.
Xerox© LCD Monitor User’s Manual 13
Installation
Installing Your LCD Monitor
Follow the instructions below to set up and install the monitor.
1
The package contains:
Display unit
Stand
2
Cover an even stable surface with a soft cloth. Place the unit face-down on the cloth. Fit the stand onto the bottom of the display unit as shown, then push until the two latches snap into their sockets.
LATCH
SOCKETS
LATCHES
14 Xerox© LCD Monitor User’s Manual
OSD Menu
3 OSD Menu
Using the OSD Menu
To create the best picture, your XR3 series has been preset at the factory with the Preset Mode Timing shown on page 21.
The OSD (On Screen Display) Menu allows the user to adjust various settings and options by following the steps below.
1
Press the MENU button to display the OSD. The OSD main menu provides an overview of the selection of controls available.
<up>to select picture advanced options utilities reset exit auto adjust brightness contrast h position v position phase clock exit
2
Press the ▲ or ▼ button to highlight the desired icon. Then, press the MENU button to activate the highlighted icon.
3
Press the ▲ or ▼ button to select the desired adjustment icon. Then, press the MENU button.
4
Press the ▲ or ▼ button to change the value of the selected item.
5
Select the exit icon to exit the OSD.
6
Repeat steps 1 through 4 to make further adjustments. All changes are stored immediately.
Xerox© LCD Monitor User’s Manual 15
OSD Menu
The OSD Options
The main menu includes the following options: picture advanced options utilities reset exit auto adjust brightness contrast h position v position phase clock exit
<up>to select picture
Adjusts picture settings such as brightness, contrast.
advanced
Allows selection of the general color tint: CUSTOM COLOR,
WARM, or COOL.
options
Adjusts picture settings such as H/V position, H size and phase.
utilities
Adjusts the setting of the display time of the on-screen menu.
Allows selection of the language used on all the on-screen menus.
reset
Restores the factory settings.
exit
Exits the on-screen menus.
16 Xerox© LCD Monitor User’s Manual
OSD Menu
The picture Menu
1
The picture menu provides access to the following menus:
<up>to select picture advanced options utilities reset exit auto adjust brightness contrast h position v position phase clock exit
2
The picture menu includes the following options:
ON DESCRIPTION auto adjust
Automatically adjust the display settings to optimize performance based on the D-SUB signal.
brightness
Controls the overall brightness.
contrast
Controls the difference between the brightest and darkest regions of the picture.
h. position
Adjusts the position of the picture left and right in the window.
v. position
Adjusts the position of the picture up and down in the window.
phase
Adjusts signal phase, which can improve focus clarity and image stability.
clock
Adjusts the width of the picture.
exit
Exits the picture menu.
Xerox© LCD Monitor User’s Manual 17
OSD Menu
The advanced Menu
1
The advanced menu provides access to the following menus: picture advanced options utilities reset exit sharpness color
1 2 3 4 5
cool natural warm user user red user green user blue exit
18
2
The advanced menu includes the following options:
ON DESCRIPTION
sharpness
Increase this setting to see crisp edges in the picture; decrease for soft edges.
color
Allows selection of the general color tint:
user, natural, warm, or cool.
cool
Inclines colors toward the blue end of the spectrum.
Fixes the red, green and blue component levels at factory settings; they cannot be independently adjusted.
natural
Inclines colors toward the natural end of the spectrum.
Fixes the red, green and blue component levels at factory settings; they cannot be independently adjusted.
warm
Inclines colors toward the red end of the spectrum.
Fixes the red, green and blue component levels at factory settings; they cannot be independently adjusted.
user
Allows the user to adjust red, green and blue color component levels independently.
exit
Exits the advanced menu.
Xerox© LCD Monitor User’s Manual
OSD Menu
The options Menu
1
The options menu provides access to the following menus: osd h position osd v position exit picture advanced options utilities reset exit
2
The options menu includes the following options:
ON DESCRIPTION
osd h. position
Moves the OSD left and right in the window.
osd v. position
Moves the OSD up and down in the window.
exit
Exits the OSD menu.
Xerox© LCD Monitor User’s Manual 19
OSD Menu
The utilities Menu
1
The utilities menu provides access to the following menus: picture advanced options utilities reset exit osd timeout 15 seconds osd background opaque translucent language exit
2
The utilities menu includes the following options:
ON DESCRIPTION osd timeout
Allows selection of the display time of the on-screen menu.
osd background
Controls the translucence of the on-screen menu’s background.
languages
Allows selection of the languages used on all the on-screen menus.
exit
Exits the utilities menu.
20 Xerox© LCD Monitor User’s Manual
4 Technical Information
Technical Information
Preset Mode Timing Chart
The screen image has been optimized during manufacture for the display modes listed below.
Video signal: (IBM PC/AT)
Dot X Line
720 x 400
640 x 480
800 x 600
1024 x 768
1280 x 1024*
Horizontal
Frequency(kHz)
31.47
31.47
37.86
37.50
37.88
48.08
46.87
48.36
56.48
60.02
63.98
79.98
Vertical
Frequency(Hz)
70.00
60.00
72.80
75.00
60.30
72.20
75.00
60.00
70.10
75.00
60
75
* 1280 x 1024 resolution is not available in 15” LCD monitor.
Xerox© LCD Monitor User’s Manual 21
Technical Information
D-SUB Connector PIN Assignment
PIN
7
8
9
10
5
6
3
4
1
2
11
12
13
14
15
1
6
11
5
10
1 5
DESCRIPTION
Red
Green
Blue
Ground
Self Test
Red Ground
Green Ground
Blue Ground
5 VDC
Ground
Ground
SDA (FOR DDC)
H. Sync
V. Sync
SCL (FOR DDC)
22 Xerox© LCD Monitor User’s Manual
Technical Information
Plug and Play
This monitor conforms to the VESA DDC (Display Data
Channel) standard, which means that when it is used with a
DDC compatible video card, the monitor is easier to set up.
With VESA DDC 1/2B, when the monitor is turned on, it will automatically notify a windows 9X/2000/XP host computer of its scanning frequencies, capabilities and characteristics. Windows
9X/2000/XP will automatically recognize the presence of the monitor and select the appropriate display resolution.
Visual Inspection
Permanently unlit or lit pixels
The standard of production techniques today cannot guarantee an absolutely fault free LCD display. A few isolated permanently lit or unlit pixels may be present. The maximum permitted number of pixel faults is stipulated in the stringent international standard ISO 13406-2 (Class II).
Example:
A 17” flat-screen monitor with a resolution of 1280 x 1024 has 1280 x 1024 = 1310720 pixels. Each pixel consists of three subpixels (red, green and blue), so there are about 4 million dots in total.
According to ISO 13406-2 (Class II), a maximum of 6 pixels and
7 subpixels may be defective, i. e. a total of 25 faulted dots. This corresponds to approx. 0.002 % of the entire screen surface.
Xerox© LCD Monitor User’s Manual 23
Technical Information
Troubleshooting
Before consulting service personnel, check the following chart for a possible cause and solution to the trouble you are experiencing.
Monitor will not turn on
• Make sure the power cord is plugged in.
No picture
• Make sure the power cord is plugged in.
• Check the signal cable connecting the LCD monitor and the computer (refer to page 12-13).
• Press the button on the front panel of the monitor.
Poor picture or abnormal picture
• Check the D-SUB cable connecting the LCD monitor and the computer (refer to page 12-13).
• Press the MENU button to adjust the Brightness
Contrast option in the OSD.
• Adjust the Color Select option in the OSD.
• Press the AUTO button on the front panel of the monitor, to automatically adjust the display mode.
Out of range message appears
• Press the AUTO button on the front panel of the monitor, to automatically adjust the display mode.
• Press the MENU button to adjust the V Position, H
Position and H Size options in the OSD.
• If using Windows 9X/2000/XP, wait a few seconds; once Windows detects the problem, a dialog will appear allowing you to manually set up the video mode according to the preset mode timing chart
(refer to page 21).
24 Xerox© LCD Monitor User’s Manual
Technical Information
Specifications
MODEL
LCD Panel Panel Size
XR3-17
17’ TFT LCD
Brightness 420
Contrast Ratio 500:1
Dot Pitch
Max. Resolution
Input Connector
Power Source
Power Consumption
Dimension
0.264mm x 0.264mm
1280x1024
48W
378x382x192 mm
X XR3-19
19” TFT LCD
400
500:1
0.294mm x 0.294mm
1280x1024
D-SUB D-SUB
AC100-240V, 50-60Hz AC100-240V, 50-60Hz
48W
426x413x210 mm
Changes are periodically made to this specifications.
Current specifications may also be obtained via the internet, www.xerox-displays.com or www.xerox-displays.info
Xerox© LCD Monitor User’s Manual 25
Technical Information
Authorized Service Centers
U.S.A.
CALIFORNIA: AUTHORIZED SERVICE CENTER
7373 HUNT AVENUE
GARDEN GROVE, CA 92841
(714) 799-3899
(800) 469-1175
(714) 379-6290 Fax
Hours: 8AM ~ 6PM - Pacific Standard Time
TEXAS: AUTHORIZED SERVICE CENTER
10849 KINGHURST SUITE # 120
HOUSTON, TX 77099
(281) 530-4100
(281) 530-4104 Fax
Hours: 8AM ~ 6PM - Central Time
EUROPE
AUTHORIZED SERVICE CENTER CONTACTS:
XOAL BVBA
RAKETSRAAT 100
B-1130 BRUSSEL BELGIUM
E-EMAIL: [email protected]
http://www.proview-repair.com
Hotline: 00800 00 88 77 66
Fax: +32-2-725-2513
Hours: 10AM ~ 12PM and 2PM ~ 5PM
Monday through Friday
26 Xerox© LCD Monitor User’s Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement