UA
CD RECEIVER
AMPLI-TUNER CD
OWNER'S MANUAL
MODE D'EMPLOI
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
1
2
3
4
5
6
7
8
9
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
10
11
12
13
14
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
i En
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
DIRECT EXPOSURE TO THE BEAM
DANGER: AVOID
INVISIBLE LASER RADIATION WHEN OPEN
NOT STARE INTO BEAM
CAUTION:DO
INVISIBLE LASER RADIATION WHEN OPEN
● The label is located on the bottom of the unit. (U.S.A and
Canada models only)
ii En
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this unit in a well ventilated, cool, dry, clean place with at
least 10 cm on the top, 10 cm on the left and right, and 10 cm at
the back of this unit — away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all connections are
complete.
Do not operate this unit upside-down. It may overheat, possibly
causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. Yamaha will not
be held responsible for any damage resulting from use of this unit
with a voltage other than specified.
To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or this unit
during a lightning storm.
Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed.
The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
Before moving this unit, press STANDBY/ON to set this unit to
the standby mode, and disconnect the AC power plug from the
wall outlet.
iii En
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave this unit alone.
19 When using this unit for a long time, this unit may become warm.
Turn the power off, then leave this unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power plug
can be reached easily.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
22 Excessive sound pressure from earphones and headphones can
cause hearing loss.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit itself
is turned off by STANDBY/ON. This state is called the
standby mode. In this state, this unit is designed to consume a
very small quantity of power.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam.
When this unit is plugged into the wall outlet, do not place your
eyes close to the opening of the disc tray and other openings to
look into inside.
The laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
CONTENTS
FEATURES............................................................. 2
SUPPLIED ACCESSORIES ................................. 2
CONTROLS AND FUNCTIONS ......................... 3
Front panel ................................................................. 3
Front panel display .................................................... 4
Remote control........................................................... 5
OTHER OPERATIONS
CONTROLLING iPod™......................................20
Using iPod™ ........................................................... 20
ADDITIONAL INFORMATION
INTRODUCTION
INTRODUCTION
TROUBLESHOOTING .......................................22
CONNECTING SPEAKERS ................................ 9
Connecting a subwoofer .......................................... 10
CONNECTING ANTENNAS.............................. 11
Connecting the FM antenna..................................... 11
CONNECTING THE POWER CABLES .......... 11
CONNECTING HEADPHONES........................ 11
CONNECTING EXTERNAL COMPONENTS ...12
NOTES ABOUT DISCS/MP3, WMA FILES.....25
GLOSSARY...........................................................27
Audio information ................................................... 27
Copyright and logo marks ....................................... 27
SPECIFICATIONS...............................................27
BASIC OPERATIONS
BASIC RECEIVER OPERATIONS .................. 13
SETTING THE SLEEP TIMER......................... 14
BASIC PLAYBACK OPERATIONS FOR DISCS
AND USB DEVICES........................................ 15
TUNER
OPERATIONS
Switching the playback information display ........... 16
Repeating playback (Repeat Play)........................... 17
Playing back randomly (Shuffle Play)..................... 17
BASIC
OPERATIONS
Connecting a USB device........................................ 12
Connecting an iPod™.............................................. 12
General..................................................................... 22
Radio reception........................................................ 22
iPod™ ...................................................................... 23
USB ......................................................................... 23
Disc Playback .......................................................... 24
Remote control ........................................................ 24
PREPARATION
PREPARATION
TUNER OPERATIONS
FM TUNING ......................................................... 18
OTHER
OPERATIONS
Automatic tuning ..................................................... 18
Manual tuning.......................................................... 18
Automatic preset tuning........................................... 18
Manual preset tuning ............................................... 19
Selecting preset stations........................................... 19
ADDITIONAL
INFORMATION
English
1 En
FEATURES
FEATURES
• Maximum RMS output power per channel
20W + 20W (10% THD, 1 kHz, 6Ω)
• 30-station FM preset tuning
• iPod playability
• Plays Audio CDs, MP3/WMA discs
• CD Text data display
• MP3/WMA file playability stored on USB
device
• Multi function remote control
■ About this manual
• This manual describes how to operate this unit using a remote control except when it is not available. Some of these operations are
also available using the front panel buttons.
• The round shaped button on the center of the remote control is called Center in this manual.
• y indicates a tip for your operation.
• Notes contain important information about safety and operating instructions.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.
SUPPLIED ACCESSORIES
This product includes the following accessories. Before connecting speakers, make sure you received all of the following parts.
Remote
control
Indoor FM antenna
USB cap*
Dock cover*
STANDBY ON
SLEEP
CD
iPod
FM
USB
PRESET
FM
TUNING
MEMORY
(U.S.A and Canada
models)
FUNCTION
MENU
DISPLAY
FOLDER
USB
SHUFFLE
REPEAT
iPod
(Other models)
MUTE
VOLUME
When the USB cap and the Dock cover are covered.
*The
2 En
USB cap and the Dock cover are supplied with this unit to cover the USB port and the iPod terminal when not using.
CONTROLS AND FUNCTIONS
INTRODUCTION
Front panel
A
B
USB
IPod
Top view
1
2
3
4
VOLUME
INPUT
STANDBY ON
PHONES
Front view
5
6
7
8
9
0
1 STANDBY/ON
Turns this unit on or sets it to the standby mode.
7 VOLUME
Adjusts the volume level.
2 Disc Tray
Loads a disc to be played back.
8 INPUT
Selects an input source.
3 Front panel display
Shows the various information such as the tuning
frequency.
9
Stops playback (see page 15).
4
Opens and closes the disc tray.
A USB port
Connect your USB device (see page 12).
English
5 PHONES
Outputs audio signals for private listening with
headphones.
0
Starts or pauses playback (see page 15).
B iPod terminal
Connect your iPod (see page 12).
6 Remote control sensor
Receives signals from the remote control.
3 En
CONTROLS AND FUNCTIONS
Front panel display
1
2
3
4
SLEEP PRESET STEREO AUTO
TUNED MEMORY
5
6
7
SHUFFLE REPEAT
MUTE
PLAYLISTS ARTISTS ALBUMS SONGS GENRES
B
8
9
0
1 SLEEP indicator
Lights up when the sleep timer is on (see page 14).
2 PRESET indicator
Lights up when you preset radio stations (see page 19).
3 STEREO indicator
Lights up when this unit is receiving a strong signal from
an FM stereo broadcast.
4 AUTO indicator
Lights up when this unit is in the Automatic Tuning mode
(see page 18).
5 SHUFFLE indicator
Lights up when you set your iPod/CD/USB in shuffle
mode.
6 REPEAT indicator
Lights up when you set your iPod/CD/USB in repeat
mode.
7 MUTE indicator
Lights up when the sound is muted.
4 En
A
8 Multi information display
Shows the various information such as the tuning
frequency.
9 TUNED indicator
Lights up when this unit is tuned into a station.
0 MEMORY indicator
Lights up when you preset radio stations automatically or
manually.
A Multi information indicator
Light up the menu currently selected (see page 20).
B Operation indicators
Show operable cursor keys when operating with the
FUNCTION or iPod menu with the menu browse mode
(see page 20).
CONTROLS AND FUNCTIONS
Remote control
SLEEP
CD
FM
iPod
USB
PRESET
FM
TUNING
MEMORY
Input
selection
keys
FUNCTION
MENU
To switch the input mode of this unit
INTRODUCTION
STANDBY ON
This remote control can operate the system components
and an iPod stationed in a terminal on the top panel of this
unit.
To operate the CD, USB device, tuner functions, or an
iPod using the remote control, you need to set this unit to
the corresponding input mode.
Press the corresponding input selection key on the remote
control (or INPUT on the front panel). The input mode
automatically changes to iPod when you connect the iPod
during the playback (see page 12).
The name of the corresponding input source appears in the
front panel display of this unit.
■ Common functions
Operations common to all modes
1
2
3
STANDBY ON
SLEEP
CD
4
FUNCTION
5
DISPLAY
iPod
FM
7
FM
TUNING
MEMORY
2 STANDBY/ON
Turns this unit on or sets it to the standby mode.
3 Input selection keys
Select the input source.
MENU
4 FUNCTION
By pressing FUNCTION, you can select DIMMER,
TREBLE, BASS, BALANCE, or ECO MODE.
FOLDER
MUTE
1 Infrared signal transmitter
Sends signals to the component you want to control.
USB
PRESET
SHUFFLE
6
The following operations are available for this unit when
it is set to any input mode.
REPEAT
VOLUME
8
5 DISPLAY
Switches the information shown in the front panel display
(see page 16).
6 MUTE
Turn off the sound. To restore the sound, press MUTE
again or press VOLUME
(down)/
(up).
7 SLEEP
Sets the sleep timer (see page 14).
8 VOLUME
(down) /
(up)
Adjusts the overall volume level.
English
5 En
CONTROLS AND FUNCTIONS
■ CD/USB mode
Operations available in CD/USB mode
The following operations are available for this unit when
the CD or USB mode is selected.
STANDBY ON
SLEEP
CD
1
iPod
FM
1
,
Skips to the beginning of the current track or next track.
Press and hold to fast reverse or fast forward (see
page 15). Press
twice to skip to the beginning of the
previous track.
USB
PRESET
FM
TUNING
MEMORY
FUNCTION
MENU
2
3
4
DISPLAY
FOLDER
SHUFFLE
MUTE
5
6
7
REPEAT
VOLUME
2 DISPLAY
Switches the disc/USB information shown in the front
panel display (see page 16).
3 FOLDER
/
Press FOLDER
/
to playback a first file of
selected folder for an MP3 or a WMA folder recorded on
disc/USB device (see page 15).
*During Shuffle Play, these buttons cannot be used.
4
Starts or pauses playback (see page 15).
5
Stops playback (see page 15).
6 REPEAT
Selects the Repeat Play mode (see page 17).
7 SHUFFLE
Select the Shuffle Play feature (see page 17).
■ FM mode
Operations available in FM mode
The following operations are available for this unit when
the FM mode is selected.
STANDBY ON
SLEEP
CD
iPod
FM
FM
PRESET
1
USB
MEMORY
TUNING
2
3
FUNCTION
MENU
4
DISPLAY
FOLDER
SHUFFLE
1 TUNING
Press TUNING
hold TUNING
/
2 PRESET
Press PRESET
page 18).
/
/
/
to Manual tuning and press and
to Automatic tuning.
/
to select a preset station (see
3 MEMORY
Starts preset memory mode.
REPEAT
4 Center
Press Center to fix the current setting.
MUTE
6 En
VOLUME
CONTROLS AND FUNCTIONS
■ iPod mode
Operations available in iPod mode
SLEEP
CD
1
2
3
4
5
6
iPod
FM
USB
PRESET
FM
TUNING
MEMORY
FUNCTION
7
8
MENU
9
DISPLAY
FOLDER
SHUFFLE
MUTE
REPEAT
0
VOLUME
1 FUNCTION
Switches between the simple remote mode and menu
browse mode.
2 Center
Press Center to enter the selected group. (Pressing Center
starts playback when a song is selected.)
INTRODUCTION
The following operations are available for the iPod
stationed in the terminal. For details on iPod operations,
see “Using iPod™” on page 20.
STANDBY ON
3
Skips to the beginning of the current track. Press and hold
to fast reverse. Press twice to skip to the previous track.
4 DISPLAY
Displays the song information while iPod is in menu
browse mode (see page 16).
5
Starts or pauses playback.
6 SHUFFLE
Selects the shuffle playback mode (see page 21).
iPod
Remote Control
7 MENU
Returns to the upper level in the iPod menu.
8
Skips to the next track. Press and hold to fast forward.
9
Press
/
or
to select an item in the selected group.
0 REPEAT
Selects the repeat playback mode (see page 21).
The supplied remote control has the same function
keys with your iPod. So, these keys are corresponding
with each other.
English
7 En
CONTROLS AND FUNCTIONS
■ Preparing the remote control
■ Using the remote control
The remote control comes with the battery already
installed. Before using the remote control for the very first
time, pull out the insulation sheet, as shown.
Use the remote control within 6 m (20 feet) of the
component you want to control and point it toward its
remote control sensor (see page 3).
Insulation sheet
VOLUME
INPUT
STANDBY ON
PHONES
Within 6 m
(20 feet)
30˚
y
30˚
STANDBY ON
SLEEP
CD
iPod
FM
USB
FM
PRESET
Remove the transparent sheet before using the remote control.
MEMORY
TUNING
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE
MUTE
REPEAT
VOLUME
Notes
• Be careful not to spill liquid on the remote control.
• Be careful not to drop the remote control.
• Do not leave the remote control in the following places:
– hot or humid places, such as near a heater or in a bathroom
– extremely cold places
– dusty places
■ Replacing the battery in the remote control
Change the battery when the operation range of the remote control decreases.
Use a straight pin to
remove the cover.
Replace the battery
with a new CR2025 battery.
Close the cover.
Notes
•
•
•
•
•
Insert the battery according to the polarity markings (+ and -).
If the battery runs out, immediately remove it from the remote control to prevent an explosion or acid leak.
If the battery starts leaking, dispose of it immediately. Be careful not to let the leaking battery acid touch your skin or clothing.
Before inserting a new battery, wipe the compartment clean.
Dispose of batteries according to your regional regulations.
8 En
CONNECTING SPEAKERS
CONNECTING SPEAKERS
Follow the procedure below to connect speakers to this unit. For information on your speakers, refer to the owner’s
manual supplied for the speakers.
CAUTION
Do not connect the power cable of this unit until all cable connections are completed.
Notes
Right speaker
PREPARATION
• Be sure to connect the left channel (L), right channel (R), “+”(red) “–”(black) properly. If the connections are faulty, no sound will be
heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lacks bass.
• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/
or the speakers.
• Use speakers with the specified impedance shown on the rear panel of this unit.
Left speaker
Speaker cables
MAINS
TUNER
SPEAKERS
FM ANT
75 UNBAL
R
L
SUBWOOFER
OUT
Rear panel
English
9 En
CONNECTING SPEAKERS
1
Remove approximately 10 mm (3/8 in) of
insulation from the end of each speaker
cable and then twist the exposed wires of the
cable together to prevent short circuits.
Connecting a subwoofer
The low frequency range of the left channel and the right
channel are mixed to output at the SUBWOOFER OUT
jack.
Connect the SUBWOOFER OUT jack on this unit
to the INPUT jack on the subwoofer using the
subwoofer cable (commercially available).
10 mm (3/8 in)
TUN
SUBWOOFER
OUT
2
Press and hold the lever.
Subwoofer cable
(commercially
available)
Red: positive (+)
Black: negative (–)
INPUT
INPUT
3
Insert one bare wire. By releasing the lever,
the lever is replaced.
Subwoofer
(commercially
available)
Red: positive (+)
Black: negative (–)
Note
Do not connect the power cable of this unit and the subwoofer
until all cable connections are completed.
■ Notes on the speaker cord
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridge. Connect
the striped (grooved, etc.) cable to the “+”(red) terminals
on this unit and your speaker. Connect the plain cable to
the “–”(black) terminals on this unit and your speaker.
10 En
CONNECTING ANTENNAS
CONNECTING ANTENNAS
To enjoy radio on this unit, connect the supplied FM antenna to the designated terminals. If there is a problem of weak
radio wave reception in your area or you want to improve radio reception, we recommend that you use commercially
available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.
Indoor FM
antenna
(supplied)
Connecting the FM antenna
1
Connect the supplied indoor FM antenna to
the FM jack of this unit.
2
Place the antenna away from this unit and
speaker cables.
FM ANT
75 UNBAL
SUBWOOFER
OUT
PREPARATION
TUNER
CONNECTING THE POWER CABLES
After you made all connections, connect the power cables of this unit and subwoofer (optional).
MAINS
TUNER
SPEAKERS
FM ANT
75 UNBAL
To an AC wall outlet
R
L
SUBWOOFER
OUT
6
MIN. SPEAKER
CONNECTING HEADPHONES
You can connect your headphones to the PHONES jack on the front panel of this unit.
The sound from the speakers stops.
VOLUME
INPUT
STANDBY ON
PHONES
English
11 En
CONNECTING EXTERNAL COMPONENTS
CONNECTING EXTERNAL COMPONENTS
You can connect a USB device or an iPod to this unit. For information on your component, refer to the owner's manual
supplied with the component.
Connecting a USB device
This unit has a USB port and can access MP3 or WMA
files saved on your USB device. Connect your USB
device to the USB port on the top panel of this unit.
For playback information of a USB device, see page 15.
USB device
Connecting an iPod™
This unit equips the iPod terminal on the top panel where
you can directly station your iPod and control playback of
your iPod using the supplied remote control.
Use this unit with the iPod dock adapter (supplied with
your iPod or commercially available) appropriate for your
iPod. If you use this unit without using an appropriate
iPod dock adapter, loose connection may result.
iPod
USB
iPod
USB
iPod
VOLUME
INPUT
STANDBY ON
PHONES
■ Supported USB devices
This unit supports USB mass storage class devices (e.g.,
flash memories) using FAT16 or FAT32 format.
Notes
• Some devices may not work properly even if they meet the
requirements.
• If your USB device is not played back after you connected it to
this unit, follow any of the procedures below.
– Set this unit to the standby mode, and turn it on again.
– Disconnect the device while this unit is in the standby mode.
– Then connect the device again and turn on this unit.
– Connect an AC adapter if supplied with the device.
• If the USB device is not played back even after you performed
the procedure(s) above, the device may not be playable on this
unit.
• Do not connect devices other than USB mass storages class
devices.
• Yamaha and suppliers accept no liability for the loss of data
saved on the USB devices connected to this unit.
As a precaution, it is recommended that the files are made
backup copies.
• Playability of and power supply to all kind of USB devices are
not guaranteed.
• Your USB device is automatically charged when your USB
device is connected to the USB port even when this unit is in
standby mode and ECO MODE is OFF.
• To remove USB device safely, disconnect after the playback is
stopped.
12 En
VOLUME
INPUT
STANDBY ON
PHONES
Notes
• Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod
touch are supported.
• Do not connect any iPod accessories (such as headphones, a
wired remote control, or an FM transmitter) to our iPod when it
is stationed in the terminal.
• Unless your iPod is firmly stationed in the terminal, audio
signals may not be output properly.
• Once the connection between your iPod and this unit is
complete, “iPod” appears in the front panel display. If the
connection between your iPod and this unit fails, a status
message appears in the front panel display. For a complete list
of connection status message, see the iPod section in
“TROUBLESHOOTING” on page 23.
• Your iPod is automatically charged when your iPod is stationed
in the terminal even when this unit is in standby mode and ECO
MODE is OFF.
• To remove iPod safely, disconnect after the playback is
stopped.
BASIC RECEIVER OPERATIONS
BASIC RECEIVER OPERATIONS
Follow the procedure below to select an input source and adjust the sound settings on this unit.
4
Press
(down) /
(up) to adjust the
volume to the desired output level.
■ To adjust the audio quality
VOLUME
Press FUNCTION to display the function
menu.
STANDBY ON
2
Press
/
repeatedly to select TREBLE,
BASS, or BALANCE and press Center.
3
Press
/
repeatedly to adjust the
setting and press Center.
PHONES
STANDBY/ON
STANDBY/ON
Input
selection
keys
VOLUME
INPUT
TREBLE: Adjusts the high frequency response.
BASS:
Adjusts the low frequency response.
BALANCE: Adjusts the volume level of each left
and right speaker channel.
STANDBY ON
SLEEP
CD
iPod
FM
USB
PRESET
FM
TUNING
MEMORY
y
TREBLE, BASS, and BALANCE are not adjustable when using
the headphones.
FUNCTION
FUNCTION
BASIC
OPERATIONS
1
INPUT
MENU
/
Center
■ To dim the display
DISPLAY
FOLDER
SHUFFLE
MUTE
1
2
3
You can dim the front panel display of this unit.
REPEAT
VOLUME
VOLUME
/
Press STANDBY/ON to turn on this unit.
The front panel display lights up.
Press one of the input selection keys or
press INPUT on the front panel to select the
desired input source. Each time you press
INPUT, the input source changes in order of
CD, iPod, FM and USB.
Press FUNCTION to display the function
menu.
2
Press
/
repeatedly to select DIMMER
and press Center.
Press
/
to select the brightness and press
Center.
■ To use the ECO mode
This mode reduces power consumption during the standby
mode. Your iPod or USB device cannot be charged during
standby mode and ECO MODE is ON.
1
Press FUNCTION to display the function
menu.
2
Press
/
repeatedly to select ECO
MODE and press Center.
3
Press
Center.
/
to select ON or OFF and press
13 En
English
Start playback on the selected source
component or select a radio station.
For information on the disc playback, see page 15,
and for information on tuning, see page 18.
1
SETTING THE SLEEP TIMER
SETTING THE SLEEP TIMER
The sleep timer sets this unit to the standby mode after the specified time elapses.
STANDBY ON
SLEEP
CD
iPod
FM
SLEEP
USB
PRESET
FM
TUNING
MEMORY
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE
MUTE
REPEAT
VOLUME
Press SLEEP repeatedly to select the desired
duration.
Each time you press the key, the duration changes as
follows.
The SLEEP indicator lights up in the front panel display.
SLEEP 30min
SLEEP 60min
SLEEP 90min
SLEEP 120min
SLEEP OFF
y
• The sleep timer is canceled if you set this unit to the standby
mode.
• If you press SLEEP while the sleep timer is set, the remaining
time appears in the front panel display.
To cancel the sleep timer
Press SLEEP repeatedly to select “SLEEP OFF”.
14 En
BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES
BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES
You can enjoy playback your audio CDs, USB devices, and MP3 or WMA files recorded on a disc/USB device. Some
operations may be different or restricted depending on the disc/USB device. Before playing back, check the
compatibility of your disc/USB device with this unit (see page 25).
STANDBY ON
SLEEP
CD
/
iPod
FM
USB
PRESET
FM
TUNING
MEMORY
• Some files may not work properly depending on the USB
device specification.
• Copyright-protected files cannot be played back.
• This unit can play back files of 4 GB in size or less.
• When the input source is USB and this unit is turned on with the
USB device connected, playback starts automatically.
To stop playback
FUNCTION
MENU
Press
DISPLAY
FOLDER
FOLDER
/
SHUFFLE
To pause playback
REPEAT
VOLUME
Press
.
To return to normal playback, press
BASIC
OPERATIONS
MUTE
.
.
To fast reverse or fast forward
To start disc playback
1
Select CD as the input source (see page 13).
2
Press
while a disc is loaded.
For an audio CD, playback starts from the first track,
and for MP3 or WMA files, playback starts in
alphanumeric order by the filename.
y
• You can open and close the disc tray by pressing
on the
front panel of this unit.
• You can also start disc playback by pressing
on the front
panel.
• When the input source is CD and this unit is turned on with a
disc loaded, disc playback starts automatically.
To fast reverse, hold down
To fast forward, hold down
.
.
To skip tracks
To skip to the start of the current track, press
To skip to the next track, press
.
To skip to the previous track, quickly press
.
twice.
To skip a folder for an MP3 or WMA file
To skip a folder, press FOLDER
/
.
■ About MP3 and WMA discs/USB device
Root
To start USB device playback
Folder
1
Select USB as the input source (see page 13).
File
2
Connect your USB device to the USB port on
this unit.
The reading time may exceed 30 seconds depending
on the number of files/folders.
For a USB device, playback starts automatically in
order by the date and time of creation if playable files
are in the USB device.
You can play back MP3 or WMA files recorded on your
CD-R, CD-RW or USB device. This unit regards files in
the disc/USB device as tracks (as shown above).
Notes
English
• Total time does not appear on the front panel for USB device
playback.
• If the USB device is partitioned, only the first partition is
displayed.
15 En
BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES
Switching the playback information display
You can switch the disc playback information shown in the front panel display of this unit. Available information differs
depending on the type of the disc/USB device.
FM
Press DISPLAY repeatedly while playing back a
disc/USB device.
Each time you press the key, the information display
changes as described in “Playback information for audio
CDs” and “Playback information for MP3 or WMA files
recorded on discs/USB devices” on page 16.
DISPLAY
PRESET
TUNING
MEMORY
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE
Note
REPEAT
Some special characters may not be shown properly.
■ Playback information for audio CDs
The following information is available during playback of an audio CD. “Track Title”, “Artist”, and “Album Title” are
available only for a CD TEXT disc.
7 Album Title
1 Elapsed time of the current track (Default)
ALBUMS
2 Remaining time of the current track
6 Artist
ARTISTS
3 Total time of the disc
5 Track Title
4 Remaining time of the disc
SONGS
Note
You can switch the playback information 1 2 5 6 7 above during playback of your iPod in the menu browse mode (see page 21).
■ Playback information for MP3 or WMA files recorded on discs/USB devices
The following information is available during playback of an MP3 or WMA files recorded on discs/USB device.
1 Elapsed time of the current file
5 Album Title
ALBUMS
4 Artist
2 File Name
ARTISTS
3 Track Title
SONGS
16 En
BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES
Repeating playback
(Repeat Play)
Playing back randomly
(Shuffle Play)
You can repeat the playback of the selected item in your
disc/USB device.
You can play back tracks in your disc/USB device in
random order.
Note
STANDBY ON
When playing back with Shuffle Play, the remaining time of the
disc cannot be displayed.
SLEEP
CD
iPod
FM
USB
PRESET
FM
TUNING
MEMORY
STANDBY ON
SLEEP
FUNCTION
MENU
CD
iPod
FM
USB
PRESET
FM
TUNING
MEMORY
DISPLAY
FOLDER
SHUFFLE
REPEAT
FUNCTION
REPEAT
DISPLAY
VOLUME
BASIC
OPERATIONS
MUTE
MENU
FOLDER
SHUFFLE
REPEAT
SHUFFLE
MUTE
1
Play back the disc or track you want to repeat.
2
Press REPEAT to select the desired Repeat
Play mode.
Each time you press the key, the Repeat Play mode in
the front panel display changes as follows.
VOLUME
Press SHUFFLE.
Each time you press the key, the Shuffle play mode in the
front panel display changes as follows.
Audio CD
Audio CD
REPEAT ONE (Repeat Play by track)
REPEAT ALL (Repeat Play by disc)
Off (Normal playback)
MP3/WMA disc/USB device
REPEAT ONE (Repeat Play by track)
REPEAT FOLDER (Repeat Play in the folder)
REPEAT ALL (Repeat Play by disc)
SHUFFLE ALL
Off
MP3/WMA disc/USB device
SHUFFLE FOLDER*
SHUFFLE ALL
Off
* The SHUFFLE FOLDER means tracks in the folder is play
back in randomly.
Off (Normal playback)
To cancel Shuffle Play
Press REPEAT repeatedly so that the Repeat Play mode
indicator disappears from the front panel display or press
.
Press SHUFFLE repeatedly so that the SHUFFLE
indicator disappears from the front panel display or press
.
17 En
English
To cancel Repeat Play
FM TUNING
FM TUNING
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 30 stations.
Automatic tuning
Automatic preset tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
Follow the procedure below to preset radio stations
automatically.
STANDBY ON
STANDBY ON
SLEEP
SLEEP
CD
iPod
FM
USB
FM
CD
FM
USB
FM
FM
PRESET
TUNING
/
iPod
PRESET
FM
TUNING
MEMORY
MEMORY
TUNING
MEMORY
FUNCTION
FUNCTION
MENU
MENU
Center
DISPLAY
DISPLAY
FOLDER
FOLDER
SHUFFLE
REPEAT
SHUFFLE
MUTE
REPEAT
VOLUME
MUTE
VOLUME
1
Press FM to set this unit to the FM mode.
1
Press FM to set the unit to the FM mode.
2
Press and hold TUNING
/
to begin
automatic tuning.
The AUTO indicator lights up on the front panel
display.
This unit automatically detects radio stations that
have strong signals for your selection, and
automatically ends automatic tuning.
The AUTO indicator disappears from the front panel
display.
2
Press and hold MEMORY for more than 2
seconds.
The “AUTO PRESET” and “Push Center Key”
appear in the front panel display alternately.
To cancel, press MEMORY.
3
Press Center to start searching
automatically.
• Auto Preset starts at the lowest frequency toward
the highest frequency.
• This unit automatically applies a preset number to
each detected station.
4
Search will stop after finding appropriate
station and stores as a preset station.
5
Search will start again to find a next station.
Manual tuning
If the signal received from the station you want to select is
weak, tune into it manually.
1
Press FM to set this unit to the FM mode.
2
Press TUNING
/
repeatedly to tune into
the desired station manually.
y
Manually tuning into an FM station automatically switches the
tuner to monaural reception to increase the signal quality.
18 En
Notes
• You can preset up to 30 of FM stations with Auto Preset.
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
FM TUNING
Manual preset tuning
Selecting preset stations
You can tune into any desired station simply by selecting
the preset station under which it was stored (see page 18).
You can also store up to 30 stations manually.
STANDBY ON
SLEEP
STANDBY ON
SLEEP
CD
iPod
FM
USB
CD
USB
FM
PRESET
FM
PRESET
TUNING
MEMORY
iPod
FM
FM
PRESET
MEMORY
TUNING
MEMORY
/
FUNCTION
MENU
FUNCTION
/
Center
FUNCTION
MENU
DISPLAY
Center
FOLDER
/
DISPLAY
FOLDER
SHUFFLE
REPEAT
SHUFFLE
MUTE
VOLUME
VOLUME
MUTE
Tune into a radio station you want to preset.
See page 18 for tuning instructions.
2
Press MEMORY.
The MEMORY and PRESET indicators light up in
the front panel display until you cancel manual
preset.
To cancel, press MEMORY.
3
Press
/
repeatedly to select a preset
station number.
4
Press Center while the preset station number
you selected is flashing.
The MEMORY indicator disappears from the front
panel display.
1
Press FM to set the unit to the FM mode.
2
Press PRESET
station.
/
to select a preset
TUNER
OPERATIONS
1
5
REPEAT
■ To delete the preset station
1
Press FM to set the unit to the FM mode.
2
Press FUNCTION to display the function
menu. Press
/
to select PRESET
DELETE and press Center.
3
Press
/
to select the preset number
you want to delete and press Center.
Repeat steps 1 to 4 until all desired stations
are preset.
English
19 En
CONTROLLING iPod™
CONTROLLING iPod™
In addition to controlling this unit, you can operate your iPod stationed in a terminal using the supplied remote control.
Using iPod™
Once you have stationed your iPod in a terminal on the top panel of this unit (see page 12), you can enjoy playback of
your iPod using the supplied remote control. The operations of your iPod are available with the aid of front panel display
(menu browse mode) or without it (simple remote mode).
Notes
• Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod touch are supported.
• Some features may not be compatible depending on the model or the software version of your iPod.
y
• For a complete list of the remote control functions used to control your iPod, refer to “iPod mode” (see page 7).
• For a complete list of status messages that appear in the front panel display, refer to the “iPod™” section in “TROUBLESHOOTING”
(see page 23).
■ Simple remote mode
In the simple remote mode, you can operate the iPod menu
by viewing the iPod using the iPod controls or the
supplied remote control.
STANDBY ON
SLEEP
iPod
CD
iPod
FM
USB
PRESET
FM
TUNING
MEMORY
MENU
1
Press iPod to set this unit to the iPod mode.
2
Press FUNCTION and
/
to show iPod
MODE on the front panel display and press
Center.
3
Press
/
to select SIMPLE REMOTE.
Press Center while SIMPLE REMOTE is
blinking on the front panel display.
• You can also select the menu browse mode by
pressing
/
so, MENU BROWSE appears
on the front panel display. For details, refer to page
24.
4
Use MENU/
/
/ Center to operate the
iPod menu, and then press Center to start
playback of the selected song (or group).
FUNCTION
FUNCTION
Center
MENU
/
DISPLAY
FOLDER
SHUFFLE
MUTE
20 En
REPEAT
VOLUME
CONTROLLING iPod™
■ Menu browse mode
In the menu browse mode, you can operate the iPod menu
using the front panel display.
3
Note
There are some characters that cannot be displayed in the front
panel display of this unit. Those characters are replaced with
underscore “_”.
iPod menu
Repeat step 2 until you select the desired
item, and then press Center to start playback
of the desired item (group or song).
y
While playing back a track (or group) with the menu browse
mode, you can switch the playback information (such as song
name, elapsed time, artist name, or album name) displayed in the
front panel display by pressing DISPLAY.
■ Repeating playback (Repeat Play)
You can repeat playback of the selected items in your
iPod.
Press REPEAT to select the desired Repeat Play
mode.
Each time you press the key, the Repeat Play mode
changes as follows. To use properly, please check it with
your iPod.
1
Select the menu browse mode.
To choose the menu browse mode, please refer to
step 3 of "Simple remote mode" in page 20.
The top of the iPod menu appears in the front panel
display.
One (Repeat play by song)
All (Repeat play by selected group)
Off
■ Playing back randomly (Shuffle Play)
You can play back tracks in your iPod in random order.
Operation indicators
y
The operation indicators (see page 4) show the operable cursor
keys in each step.
Press
/
to select the menu, and then
press Center to enter the selected menu.
The name of the first item stored in the selected menu
appears.
Songs (Shuffle play by song)
OTHER
OPERATIONS
2
Press SHUFFLE.
Each time you press the key, the Shuffle Play mode
changes as follows. To use properly, please check it with
your iPod.
Albums (Shuffle play by albums)
Off
ARTISTS
y
English
• The Multi information indicators (see page 4) show the iPod
menu currently selected.
• To return to the upper level in the iPod menu, press MENU.
21 En
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
General
Problem
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
Cause
Remedy
See
page
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
11
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and
then use it normally.
—
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
on the front panel (or the input selection keys on the
remote control).
—
Speaker connections are not secure.
Secure the connections.
9
The volume is turned down.
Turn up the volume.
—
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by
this unit.
—
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
9
There is noise
interference from
digital or radio
frequency
equipment.
This unit is too close to the digital or
high-frequency equipment.
Move this unit further away from such equipment.
—
No sound
Radio reception
Problem
FM stereo reception is
noisy.
FM
22 En
Cause
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Remedy
See
page
Check the antenna connections.
11
Try using a high-quality directional FM
antenna.
—
Use the manual tuning method.
18
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
Adjust the antenna position to eliminate
multi-path interference.
—
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
Use a high-quality directional FM antenna.
—
Use the manual tuning method.
18
TROUBLESHOOTING
iPod™
Note
In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to your iPod (see
page 12).
Status message
Cause
iPod Connecting
This unit is in the middle of recognizing
the connection with your iPod.
Remedy
See
page
This unit is in the middle of acquiring
song lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to this unit.
Unknown iPod
The iPod being used is not supported by
this unit.
iPod
Your iPod is properly stationed in an
iPod terminal.
iPod Unplugged
Your iPod was removed from an iPod
terminal.
Turn off this unit and reconnect the iPod.
12
Try resetting your iPod.
—
Only iPod (Click and Wheel), iPod nano, iPod mini,
and iPod Touch are supported.
—
Station your iPod back in an iPod terminal.
12
USB
Note
In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to the USB device
(see page 12).
Status message
Cause
Remedy
See
page
Not Connected
The USB device is not connected
firmly.
Connect the USB device again.
12
Not Supported
Connected the USB device not playable
on this unit.
Connect playable USB device.
12
Over Current
Connected the USB device not playable
on this unit.
Connected the USB device diagonally.
Disconnect the USB device. Change input source
other than USB and select USB as input source
again. Then connect playable USB device again.
12
ADDITIONAL
INFORMATION
English
23 En
TROUBLESHOOTING
Disc Playback
Problem
Cause
Remedy
See
page
Power turns on but
immediately shuts
off.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
11
No sound or
distorted sound
The sampling rate of a MP3 or WMA file
may not be compatible with this unit.
Check the sampling rate and bit rate of an MP3 or
WMA file are compatible with this unit.
25
Disc playback does
not start.
You may use a CD-R/RW that is not
finalized.
Finalize the CD-R/RW.
—
The disc label may not be facing up.
Check that the disc label is facing up.
—
The disc may be defective.
Try to play back another disc. If the same problem
does not happen, the disc you want to play back is
defective.
—
MP3/WMA disc may not contain
sufficient music tracks to be played back.
Check that your MP3/WMA disc contains at least 5
MP3/WMA music files. If the number of files is
small, the disc may not be recognized.
—
The sampling rate of a MP3 or WMA file
may not be compatible with this unit.
Check the sampling rate and bit rate of an MP3 or
WMA file are compatible with this unit.
25
Improper USB device connections.
Connect the USB device again.
12
The MP3 or WMA formats are not
compatible with this unit.
Replace the file with a correctly recorded file
playable with this unit.
25
USB playback does
not start.
Remote control
Problem
The remote control
does not work nor
function properly.
24 En
Cause
Remedy
See
page
The remote control may be operated
outside its operation range.
For information on the remote control operation
range, refer to “Using the remote control”.
8
The remote control sensor on this unit
may be exposed to direct sunlight or
lighting (invented fluorescent lamps).
Change the lighting or orientation of this unit.
—
The battery may be worn out.
Replace the battery with new one.
8
There are obstacles between the sensor of
this unit and the remote control.
Remove the obstacles.
—
NOTES ABOUT DISCS/MP3, WMA FILES
■ Discs (audio CDs) playable with this unit
MP3
This player is designed for playing back compact discs
bearing the marks shown below. Never attempt to load
any other type of disc into the unit. The unit can also play
back 8-cm (3-inch) compact discs.
MP3 is a standard technology and format for compressing
an audio sequence into a small-sized file. However, the
original level of sound quality is preserved during
playback.
The playable formats are:
• MPEG-1 Audio Layer-3
Bitrate*: 32-320 kbps
Sampling frequency: 44.1/48/32 kHz
• MPEG-2 Audio Layer-3, 2
Bitrate*: 8-160 kbps
Sampling frequency: 24/22.05/16 kHz
* Variable bitrate is supported.
....
Compact discs (digital audio)
The most popular discs for commercially
available audio CDs.
....
CD-R,CD-RW digital audio discs
Music CDs made by copying onto a CD-R
or CD-RW (including MP3 or WMA
format files).
Notes
• Be sure to use a CD-R or CD-RW disc made
by a reliable manufacture.
• Be sure to use a CD-R or CD-RW disc which
has at least one of the following phrases on
the disc or disc case.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
• Be sure to use a finalized CD-R or CD-RW
disc.
....
CD-TEXT discs
The discs recorded with text data such as
album titles, track titles and artist names.
Note
This compact disc player may not be able to play back some
CD-RW discs or discs on which recording was not made
correctly.
To prevent a malfunction of this unit:
• Do not use any nonstandard
shaped disc (heart, etc.) available
on the market because it might
damage the unit.
■ About MP3 and WMA files
You can play back MP3 and WMA files recorded on a
CD-R/CD-RW and those stored on a USB device.
“WMA (Windows Media Audio)” is a Microsoft file
format for encoding digital audio files similar to MP3
though can compress files at a higher rate than MP3.
The playable formats are:
• Version 8
• Version 9 (Standard and variable bitrates are
supported. Professional and Lossless are not
supported.)
• High Profile
Bitrate*: 32-320 kbps
Sampling frequency: 48/44.1/32 kHz
• Mid Profile
Bitrate: 16-32 kbps
Sampling frequency: 22.05/16 kHz
* Both constant and variable bitrates are supported.
Notes
• Playback for Data Disc starts in alphanumeric order of files.
• Playback for USB starts in order by date and time of file
creation.
• Copyright-protected WMA (DRM) files cannot be played back
by this unit.
• The disc must be ISO9660 compatible.
• The maximum file and folder numbers are as follows.
Data Disc
USB
Maximum total number of file
and folder*
512
9,999
Maximum folder number*
255
255
Maximum file number per
folder
511
255
ADDITIONAL
INFORMATION
• Do not use a disc with tape, stickers, or paste on it. If
you use such a disc, the disc may get stuck in the
unit, or damage to the unit may result.
WMA
* The root is counted as one of the folders.
English
25 En
NOTES ABOUT DISCS/MP3, WMA FILES
■ Notes about handling compact discs
To play back an 8-cm (3-inch) CD
• Always handle a disc with care so that its surface is not
scratched.
Place it in the inner recessed area of the disc tray. Do not
put a normal (12-cm) CD on top of an 8-cm (3-inch) CD.
Note: Do not use any lens cleaners as they may be a
cause of malfunction.
• Compact discs are not subjected to wear during
playback, but damage to the disc surface when the disc
is being handled can adversely affect the disc playback.
• Be sure to use a felt-tip pen or similar writing tool
when writing on the label side of the disc. Do not use a
ballpoint pen, pencil, or other hard-tipped writing tool,
as these may damage the disc and may adversely affect
the disc playback.
• Do not warp discs.
• When a disc is not being used, remove it from the unit
and store in an appropriate case.
• When removing or storing a disc, be careful not to
scratch the playing surface.
• Compact discs are not affected by small particles of
dust or fingerprints on their playing surface, but even
so they should be kept clean. Wipe by using a clean,
dry cloth.
Do not wipe with a circular motion; wipe straight
outward from the center.
• Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, anti-static spray or liquid,
or any other chemical-based liquid because such
substances might irreparably damage the disc’s
surface.
• Do not expose discs to direct sunlight, high
temperature or high humidity for a long period of time,
as these might warp or otherwise damage the disc.
No!
26 En
GLOSSARY
■ Track
Audio information
A CD can be divided into a number of segments (tracks).
Each division is called a track number.
■ MP3 (MPEG Audio Layer-3)
One of the audio compression methods used by MPEG. It
employs the irreversible compression method, which
achieves a high compression rate by thinning out the data
of hardly audible part to the human ears. It is said to be
capable of compressing the data quantity by about 1/11
(128 kbps) while maintaining a similar audio quality to
music CD.
■ PCM (Pulse Code Modulation)
■ WMA (Windows Media Audio)
An audio compression method developed by Microsoft
Corporation. It employs the irreversible compression
method, which achieves a high compression rate by
thinning out the data of hardly audible part to the human
ears. It is said to be capable of compressing the data
quantity by about 1/22 (64 kbps) while maintaining a
similar audio quality to music CD.
Copyright and logo marks
A signal that is changed to digital format without
compression. A CD is recorded with 16-bit sound at
44.1 kHz. This signal also has a type called Packed PCM
(PPCM) that can be compressed without any loss of data.
MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson Multimedia.
■ Sampling frequency
iPod™
The number of sampling (process for digitalizing analog
signals) per second. In principle, the higher the sampling
rate, the wider the frequency range that can be played
back, and the higher the quantized bit rate, the finer the
sound that can be reproduced.
“iPod” is a trademark of Apple Inc., registered in the U.S. and
other countries.
SPECIFICATIONS
■ PLAYER SECTION
■ TUNER SECTION
Playback System
FM
• CD, CD-R/RW
Laser
• Type ...........................................Semiconductor laser GaAs/GaAlAs
• Wave length............................................................................780 nm
• Output power ..........................................................................10 mW
Audio Performance
• DAC............................................................................192 kHz/24 bit
■ AMPLIFIER SECTION
■ GENERAL
• Power Supply
[U.S.A. and Canada models]............................... AC 120 V, 60 Hz
[Australia model] ................................................ AC 240 V, 50 Hz
[Asia model]............................................AC 220-240 V, 50/60 Hz
[China model]...................................................... AC 220 V, 50 Hz
[Korea model] ..................................................... AC 220 V, 60 Hz
[Taiwan model] ............................................AC 110-120 V, 60 Hz
• Power consumption................................................................... 25 W
• Standby Power consumption*.......................................... 1 W or less
• Dimensions (W x H x D) .................................. 180 x 117 x 303 mm
(7-1/16 x 4-5/8 x 11-15/16 in)
• Weight ............................................................... 3.1 kg (6 lbs. 13 oz.)
* When ECO MODE is ON.
ADDITIONAL
INFORMATION
• Maximum RMS output power per channel
(6 Ω , 1 kHz, 10% THD) ...........................................20 W + 20 W
• Total harmonic distortion (1 kHz)
CD 10W, 6Ω ........................................................................ 0.03 %
• Output level/Impedance
PHONES (volume max) ................................................0.6 V/32 Ω
• Tuning Range
[U.S.A and Canada models]..............................87.5 to 107.9 MHz
[Other models] .............................................. 87.50 to 108.00 MHz
• Sensitivity
FM (S/N 30 dB) ................................................... 7dBμVm (EMF)
Specifications are subject to change without notice.
English
27 En
© 2008 Yamaha Corporation All rights reserved.
Printed in Malaysia
WQ57120