3.0 Gallon
TITAN TF SERVER
USE & CARE INFORMATION
CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING.
SEE NOTE 1 of DAILY CLEANING.
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
40359.0000C 10/08 ©2007 Bunn-O-Matic Corporation
INTRODUCTION
This server is intended for use with a BUNN® TITAN DUAL, or TITAN SINGLE coffee brewer only. When
proper precautions are followed, 1.5 to 3.0 gallons of coffee may be brewed directly into the server and then
transported to a remote serving location. The server must be placed on a sturdy counter or shelf.
USER NOTICES
The notices on this server should be kept in good condition. Replace unreadable or damaged labels.
#26186.0000
DAILY CLEANING
CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY
NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method
consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing
solution using an approved non-chlorine sanitizer. Do not submerge server.
1. Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server
completely by opening the faucet.
2. Remove the lid, fill server with cleaning solution and thoroughly clean the inside of server.
3. Rinse server thoroughly using fresh water rinse.
4. Fully fill server with sanitizing solution for 5 minutes then drain through fully open faucet.
5. Remove the faucet handle/stem assembly by unscrewing the faucet nut just behind the faucet handle.
6. Use enclosed cleaning brush to thoroughly clean the faucet spout and connector.
7. Remove the cap, sight gauge tube and washers.
8. Use enclosed cleaning brush to thoroughly clean the fill tube of the lid assembly and sight gauge tube.
9. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts and lid in a mild detergent and water
solution. Rinse the parts in hot water. Sanitize the parts for five minutes, then air dry completely.
10.Reassemble the faucet/stem assembly and attach it to the faucet.
11.Install the sight gauge tube and washers in the shroud and secure with the shroud cap.
12.Wash the entire outside surface of the server with a clean damp cloth.
2
40359 082807
SERVER
28
29
27
15
16-17
25
11
12
13
26
30
Vertical Faucet
6
1
7
2
3
4
8
5
18
8
19
15
14
22
9
21
20
23
24
P3896
REPLACEMENT PARTS
1. 39542.1000
Shroud, Sight Gauge 3.0 Gal.
16. 39487.1000
(Includes Item 4)
17. 40106.0000
2. 35010.0000
Plate, Decal Mounting
18. 26186.0000
3. 35009.0000
Decal, Bunn
19. 40097.0000
4. 35004.0002
Backing, Sight Gauge 3.0 Gal.
20. 32591.1000
5. 35005.0003
Sight Gauge Tube 3.0 Gal.
21. 12422.0001
6. 39083.0000
Cap, Shroud
22. 39543.0000
7. 02367.0000
Screw, Truss Head #6-32 x .62”
23 12422.0012
8. 39143.0001
Washer, Sight Gauge Tube
24. 40271.0000
9. 39081.0000
Handle, Faucet, Bunn (Horizontal Faucet) 25. 01221.0000
10. 35003.0000
Nut, Faucet Spout (Horizontal Faucet) 26. 03093.0002
11. 00601.0000
Faucet Spring
27. 26685.0000
12. 29164.0000
Faucet Stem
13. 00600.0000
Faucet Seat Cup
28 26684.0000
14. 35074.0000
Screw, Hex Hd Black M4 x .7x25
29. 29165.0001
15. 40132.0000
Spout, Faucet (Horizontal Faucet)
30. - - - - - - - - 41159.0000
Shank, Faucet (Vertical Faucet)
31. 35301.0000
3
13
12
11
10
Lid Assembly 3.0 Gal. (Includes item 17)
Cap Assembly
Decal, Warning Hot Liquid
Spacer
Tube, Silicone .50” I.D. x 2.0”(Cut to length)
Clamp, Tube .59”/.66” I.D.
Guard, Faucet
Clamp, Tube .81”/.97” I.D.
Cover, Bottom
C-Ring, Faucet Shank
Wing Nut, Faucet
Faucet Assy (Includes items 11, 12, 13, 28, 29 and 30)
Handle, Faucet
Bonnet, Faucet
Faucet Body (Not available. Order item 27)
Brush, Cleaning (Not Illustrated)
40359 102708
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) All equipment other than as specified below: 2 years parts and 1 year labor.
2) Electronic circuit and/or control boards: parts and labor for 3 years.
3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis:
parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by
it will be commercially free of defects in material and workmanship existing at the time of manufacture and
appearing within the applicable warranty period. This warranty does not apply to any equipment, component or
part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect,
alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is
conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone
at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by
BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior
authorization from BUNN that the defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN
are not authorized to make modifications to this warranty or to make additional warranties that are binding on
BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and
should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its
exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts
and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective
components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace
the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF
THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S
SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,
loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute
equipment, facilities or services, or any other special, incidental or consequential damages.
BrewWISE, BrewLOGIC, BrewWIZARD, BUNN Gourmet Ice, BUNN Pour-O-Matic, BUNN, Bunn-OMatic, Bunn-O-Matic,
BUNNlink, BUNNserve, BUNN Espress, DBC, Dr. Brew, Dual, EasyClear, EasyGard, Easy Pour, FlavorGard, Gourmet Ice,
Gourmet Juice, High Intensity, IMIX, Infusion Series, Quality Beverage Equipment Worldwide, The Mark of Quality in Beverage Equipment Worldwide, My Café, PowerLogic, Safety-Fresh, Scale-Pro, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, System III, ThermoFresh, 392, AutoPOD, AXIOM, Beverage Profit Calculator, Beverage
Bar Creator, BrewMETER, BUNNSERVE, BUNNsource, Coffee At Its Best, Cool Froth, Digital Brewer Control, Intellisteam,
Nothing Brews Like a BUNN, Pouring Profits, Pulse Wave, Signature Series, Silver Series, Smart Heat, Tea At Its Best, The
Horizontal Red Line, Titan, Ultra, are either trademarks or registered trademarks of Bunn-O-Matic Corporation.
4
40359 100908