Yamaha DPX-1300 G Owner's Manual

G
DPX-1300
DPX-1300
C2005
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
10_DPX-1300-Cover1-4_G.p65
1
DIGITAL CINEMA PROJECTOR
PROJECTEUR CINEMA NUMERIQUE
All Rights Reserved.
BEDIENUNGSANLEITUNG
Printed in Japan
WF80500
9/22/05, 4:34 PM
Caution: Read this before operating this unit.
• To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Installation
• Install this unit in a well-ventilated, cool, dry, clean place with
at least 30 cm (1 feet) clearance on the top, right and left, and
at the back of this unit — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
• Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds. To prevent fire or
electrical shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
• Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
• On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may cause electrical
shock to the user and/or damage to this unit.
• Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to restrict heat dissipation. If the temperature
inside this unit rises too much, it may cause fire, damage to this
unit, and/or personal injury.
• When installing this unit on the ceiling, make sure the ceiling
has sufficient strength to support this unit and the ceiling
mounts for an extended period of time. Installation must be
performed only by qualified service personnel.
• Install this unit near the AC outlet and where the AC power
plug can be reached easily.
Operation
• Remove the lens cover before starting any operation of this unit
to prevent the heat from staying around the lens. Operation
with the cap on may cause damage to this unit.
• Do not plug in this unit to a wall outlet until all connections are
complete.
• Only the voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than that
specified.
• When not planning to use this unit for a long period of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
• When disconnecting the power cord from the wall outlet, grasp
the plug; do not pull the cable.
• Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
Others
• Clean the lens carefully so as not to create any scratches by
using a blower or lens paper.
• Replace the lamp when the LAMP warning indicator blinks in
red after the lamp usage has exceeded 2000 hours. Follow the
lamp replacement procedure described in this manual.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an appropriate
3 pin plug fitted. For details, refer to the instructions described
below.
Note
•
The plug severed from the mains lead must be destroyed, as a plug with
bared flexible cord is hazardous if engaged in a live socket outlet.
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN-AND-YELLOW:
BLUE:
BROWN:
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be
connected to the terminal in the plug which is marked by the letter
E or by the safety earth symbol or coloured GREEN or GREENand-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
• Do not use force on switches, knobs and/or cords.
• Take care of this unit so that no foreign objects and/or liquid
drop inside this unit.
• To prevent damage by lightning, keep the power cord out and
outdoor antennas disconnected from a wall outlet or te unit
during the lightning storm.
• Do not look into the lens while this unit is turned on. It may
cause serious damage to your eyesight.
• Before moving this unit, press STANDBY/ON to set this unit
in the standby mode, and disconnect the AC power plug from
the wall outlet.
• Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reason.
i
10_DPX_1300_cau_G
1
EARTH
NEUTRAL
LIVE
9/20/05, 5:07 PM
Table of contents
1 Getting started
2
Inappropriate places for installation ....... 2
Accessory check .................................... 2
2 Features
3
3 Controls and functions
4
4 Remote control
6
5 Preparation
10
6 Installation
12
Setting up the DPX-1300 ..................... 12
Projection distance ............................... 13
Projection image position ..................... 14
7 Connection
15
Connecting to AV components ............. 15
Connecting to computer devices ......... 16
8 Projection
Getting started
1
Features
2
Controls and functions
3
Remote control
4
Preparation
5
Installation
6
Connection
7
Projection
8
Menu
9
Memory function
10
Reference
11
17
Checking installation and connections ... 17
Turning the projector power on ............ 18
Selecting an input signal ...................... 20
Adjusting the image ............................. 25
9 Menu
27
Menu configurations ............................ 27
Menu items .......................................... 28
Menu operations .................................. 38
10 Memory function
(Saving, Recall, Lock, Copy, Reset)
11 Reference
48
55
55
56
58
60
62
63
64
65
English
Glossary ...............................................
Compatible signal types .......................
Maintenance .........................................
Troubleshooting ....................................
Message display ..................................
LED Indicator meanings .......................
Specifications .......................................
Dimensional drawing ............................
1
11_DPX-1300_E.p65
1
9/20/05, 5:07 PM
1 Getting started
◆Inappropriate places for installation
If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place
to install this unit by avoiding the places listed below.
1. Places where the temperature and humidity vary greatly
• Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely
low.
• This unit must be used within a temperature range of 5 to 35°C.
2. Places without adequate ventilation
• Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.
• Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.
• Install this unit on the firm surface.
• Do not cover this unit with a tablecloth, etc.
• Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.
• If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.
3. Places where it gets dusty
• If the filter is blocked with dust, the temperature of this unit may become too high.
4. Places with too much vibration or impact
• Vibration and impact can damage parts of this unit.
5. Places where this unit gets exposed to water or high humidity
• If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.
6. Unstable places
• If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.
7. In close proximity to a Radio or Stereo
• The unit may interfere with reception if placed in close proximity to a radio or television receiver.
Warning
•
To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.
◆Accessory check
Please check that all accessories listed here are included in your package.
• Remote control
• Batteries (AA, UM-3 or R6)
• Power cable
• Pin/BNC adapters
• Lens cap
AUTO
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
ESCAPE
MENU
ASPECT
INPUT
RESET
HIDE
LIGHT
STILL
INPUT
S VIDEO
A
HDMI
VIDEO
B
DVI
D4
MEMORY
1
2
3
4
5
6
2
11_DPX-1300_E.p65
2
9/20/05, 5:07 PM
2 Features
Highly configurable electronic adjustment gives you the
freedom to place the projector wherever you want
A short focal length, high power zoom, and fully vertically adjustable lens allow you to use the
projector in a wide range of environments. You can also use the remote control to access many
lens functions such as focus, zoom, and lens shift to fine-tune the projector from your viewing
position.
2
Features
Uses the DMDTM device 720p DarkChip3TM
The projector uses the high contrast “720p DarkChip3TM”, to reduce black levels even further
and reproduce contrasts close to that of a film.
Adjust 7 colors independently (including white), or use the
automatic color balance function
The DPX-1300 allows you to adjust the 7-axis WRGBYCM color coordinate and gain
parameters directly. For better consistency, you can also control color temperature and RGB
balance together, allowing you to check that the changes you make are always consistent with
your preferences.
The digital interface provides sharp, detailed images
The DPX-1300 is equipped with an HDMI terminal, which is set to become the standard for the
coming generation of products. Connect to a DVD player or set-top box with a HDMI terminal
to receive digital image data directly, and enjoy completely digitally processed images.
Compatible with the content protection function of HDCP.
Intelligent memory functions
The DPX-1300 can store six image memory settings, called memory numbers, for each input
jack. For each memory number, you can set parameters for different input resolutions, and the
unit will switch to the appropriate parameters when it begins displaying an image of an
appropriate resolution. For example, the unit automatically changes display settings without
changing memory numbers when you change from watching a DVD to watching a HDTV
image for which you have set different image menu item parameters.
In-line menus for image adjustment
You can access image adjustment menu items at the touch of a button, and adjust images while
viewing them without opening the menu screen.
English
3
11_DPX-1300_E.p65
3
9/20/05, 5:07 PM
3 Controls and functions
◆Main unit <Front panel and controls>
Front remote control sensor
STANDBY/ON indicator
Lamp cover
Exhaust vent
Ventilation inlet
STANDBY/ON
1
2
Lens
3
4
Lens cap
MENU
ESCAPE
PATTERN
SETTING
5
Adjustable feet
ASPECT
Makes small adjustments to
the projection angle
INPUT
LAMP
1
COVER
TEMP
FAN
6
7
8
9
0
DIGITAL CINEMA PROJECTOR DPX-1300
1 LED Indicators
The main unit is equipped with 5 indicators to display various states of operation. See page 63 for explanations of the LED indicator
meanings.
STANDBY/ON
A STANDBY/ON indicator
A
(There is also an LED on the front panel of the main unit.)
B LAMP warning indicator
MENU
ESCAPE
PATTERN
SETTING
C COVER warning indicator
D TEMP warning indicator
ASPECT
B
C
INPUT
LAMP
COVER
TEMP
FAN
E
D
E FAN warning indicator
2 STANDBY/ON button
Switches the unit between Standby and On (operational)
modes.
3 ESCAPE button
Switches the settings and adjustments menu display on and off.
8 SETTING button
Selects lens adjustment modes.
Exits from submenus.
9 INPUT button
4 PATTERN button
Switches the input signal selection menu display on and off.
Switches the built-in test pattern on and off.
5 ASPECT button
Turns the display aspect menu for the project image on and off.
6
7 MENU button
0 Cursor buttons
Use the h, g, +, - buttons for system operations, menu item
selection, and changing system values.
(Enter) button
Sets values when the DPX-1300 is displaying the menu. When
the menu is not displayed, the DPX-1300 displays the in-line
image quality adjustment menu. (☞ page 47)
4
11_DPX-1300_E.p65
4
9/20/05, 5:07 PM
◆Main unit <Rear panel / Connections>
3
Controls and functions
Rear remote control sensor
q
w
e
OUT
DVI
HDMI
1
t
RS-232C
TRIGGER OUT
IN
REMOTE
INPUT A
INPUT B
RGB/YPBPR/YCBCR
r
D4 VIDEO
2
G/Y
3
B/PB/CB
R/PR/CR
4 5
1 INPUT B (D-sub 15 pin)
Receives component video and RGB (RGB/YPBPR/YCBCR)
signals. Use a D-sub monitor cable to connect components to
this jack.
2 D4 VIDEO (D jack)
Receives signals output from the D jacks of other AV
components. It is compatible with D1 - D4 formats.
3 - 7 INPUT A (BNC jacks)
Receive component video and RGB signals. Connect
component signal connectors from AV components to input
jacks 3 - 5, and RGB signal connectors from computers to
input jacks 3 - 7. Use BNC cables for these connections.
3 G/Y
(G, or luminance signal)
4 B/PB/CB (B, or color difference signal)
5 R/PR/CR (R, or color difference signal)
6 HD/SYNC (Horizontal sync signal, composite sync signal)
7 VD
(Vertical sync signal)
8 S VIDEO (Mini DIN jack)
Receives signals from S-VIDEO output jacks of other AV
components. Use an S-VIDEO cable for these connections.
VD
HD/SYNC
6
7
S VIDEO
8
VIDEO
9 0
9 AC inlet
Insert the supplied AC power cable here.
0 VIDEO (Pin Jack)
Receives composite video signals from the VIDEO output
jacks of other AV components. Use a video pin cable for these
connections.
q DVI (DVI jack)
Receives RGB signals from computers or AV components. Use
a DVI cable for this connection.
w HDMITM (HDMITM jack)
Receives HDMITM signals from computers or AV components.
e REMOTE IN / OUT jack
Connect the remote control to the REMOTE IN jack if you
want to use it through a cable. The REMOTE OUT jack
outputs the signal received through the REMOTE IN jack
without any change.
r RS-232C (D-sub 9 pin)
For use in servicing this unit.
t TRIGGER OUT
5
11_DPX-1300_E.p65
5
9/20/05, 5:07 PM
English
Outputs control signals to external components. This output
provides a potential of 12 V/ maximum 200 mA when this unit
is projecting. Use the supplied trigger-out DC plug (for US
model only) to control external components.
4 Remote control
◆ Remote control functions
Buttons on the remote control with identical names to those on the main unit perform identical functions. When using the remote control,
point it at the remote control sensor on the front or back of the main unit from a distance of 7m (23 feet) or less.
1 Transmit indicator
Lights up when the remote control sends infrared signals to the
main unit.
1
2 AUTO button
e
2
3 V.POS button
AUTO
3
Switches on or off the vertical adjustment mode for the entire
image.
r
V. POS
ZOOM
FOCUS
4 ZOOM button
4
IRIS
SETTING
t
MENU
ESCAPE
Switches on or off the size adjustment mode for the image the
DPX-1300 is projecting.
PATT
5
6
Automatically sets the DPX-1300 to the best settings for the
type of signal it is currently receiving.
5 IRIS button
Switches on or off the lens iris change mode.
y
6 ESCAPE button
Exits from submenus.
7 Cursor buttons
7
Use the h ,g, +, - buttons to move the cursor within the onscreen display.
u
8 ASPECT button
8
INPUT
ASPECT
Turns the display aspect menu for the project image on and off.
9 RESET button
Resets all adjustable parameters to their default settings.
o
9
RESET
0
STILL
0 STILL button
HIDE
Stops a moving image, displaying a still of the image the DPX1300 is projecting. Press STILL again to cancel this effect.
p
LIGHT
q INPUT area
INPUT
q
i
S VIDEO
A
HDMI
VIDEO
B
DVI
Selects the INPUT jacks directly.
w MEMORY area
Calls stored memory (all parameter settings) directly.
e
D4
button
Switches the unit between Standby and On (operational)
modes.
MEMORY
1
2
3
4
5
6
w
r FOCUS button
Switches on or off the focus adjustment mode for the image the
DPX-1300 is projecting.
t PATT (PATTERN) button
Switches on and off the built-in test pattern.
y MENU button
Switches on and off the settings and adjustments menu display.
u
(Enter) button
Sets values when the DPX-1300 is displaying the menu. When
the menu is not displayed, the DPX-1300 displays the in-line
image quality adjustment menu. (☞ page 47)
6
11_DPX-1300_E.p65
6
9/20/05, 5:07 PM
i INPUT button
Switches on and off the input signal selection menu display.
o LIGHT switch
Moving this switch lights the high-use AUTO (2), ESCAPE
(6), ASPECT(8) ,
(e), MENU (y), and INPUT (i)
buttons. The light disappears if you do not perform any
operation within 10 seconds.
AUTO
V.POS
ESCAP
IRIS
E
ZOOM
FOCUS
PATT
SETT
ING
MEN
U
-1
ID
ASPE
CT
RESE
p HIDE button
INP
UT
T
STILL
EO
Temporarily halts projection of the image the DPX-1300 is
currently displaying. Press again to cancel this effect.
a Remote control code switch
INP
A
O
UT
D4
LIG
HT
HDM
I
B
1
-2
HID
E
S VID
VIDE
ID
DVI
a
ME
MO
RY
2
4
3
5
6
Selects ID-1 or ID-2 when operating two main units with one
remote control. You can set the ID for the main unit in the
menu (The default setting is ID-1).
Connect this jack and REMOTE IN jack on the main unit using
a cable (commercially available) to use the remote control with
a wired connection. (☞ page 8)
4
s
Remote control
s Remote control cable jack
English
7
11_DPX-1300_E.p65
7
9/20/05, 5:07 PM
◆Loading the batteries into the remote control
1. Remove the battery compartment cover.
2. Insert two batteries (AA, UM3, or R6 type), matching the polarity
markings on the batteries with those in the battery
compartment.
1
3
2
3. After loading the batteries, close the cover until it snaps into
place.
Warning
•
If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the
batteries for new ones.
•
Do not mix old and new, or different types of batteries.
•
Remove the batteries if you do not plan to use the unit for a long time.
•
If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact
with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compartment thoroughly
before installing new batteries.
◆Using the remote control with a wired connection
Use a 2P monaural miniplug cable (commercially available) to connect the remote control jack on the underside of the remote control to the
REMOTE IN jack on the main unit. Use the wired remote control configuration to control the DPX-1300 without having to be within range
of the remote sensor.
AUTO
IRIS
ESCAPE
V.POS
ZOOM
FOCUS
PATT
SETTING
MEN
U
ID
ASPE
CT
RESET
STIL
S VIDE
L
HID
O
INPU
A
VIDEO
2
INPU
E
LIG
HT
T
HDMI
B
D4
1
4
INP
UT
DVI
T
3
5
6
OUT
DVI
HDMI
IN
REMOTE
RS-232C
TRIGGER OUT
INPUT A
INPUT B
RGB/YPBPR/YCBCR
D4 VIDEO
G/Y
B/PB/CB
R/PR/CR
HD/SYNC
VD
S-VIDEO
VIDEO
8
11_DPX-1300_E.p65
8
9/20/05, 5:07 PM
ID
-2
-1
◆ Limits for using the remote control
Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits
described here.
Distance to sensor
Angle to sensor
7m
(approximate value)
30˚ vertically and horizontally
(approximate value)
OUT
HDMI
AUTO
D4 VIDEO
G/Y
B/PB/CB
R/PR/CR
ZOOM
IRIS
SETTING
ASPECT
RESET
FOCUS
PATT
V. POS
ZOOM
IRIS
SETTING
MENU
ESCAPE
INPUT
ASPECT
HIDE
RESET
LIGHT
STILL
S-VIDEO
TRIGGER OUT
VIDEO
4
FOCUS
PATT
MENU
INPUT
HIDE
LIGHT
STILL
INPUT
INPUT
A
HDMI
S VIDEO
B
DVI
VIDEO
D4
A
HDMI
B
DVI
Remote control
VIDEO
RS-232C
VD
HD/SYNC
AUTO
V. POS
ESCAPE
S VIDEO
IN
REMOTE
INPUT A
INPUT B
RGB/YPBPR/YCBCR
D4
MEMORY
MEMORY
1
2
3
1
2
3
4
5
6
4
5
6
Use within a left/right arc of 30 degrees
Use within a vertical arc of 30 degrees
Warning
•
Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.
•
Objects placed between the main unit remote sensor and the remote control may block the remote control signal and inhibit
functioning.
English
9
11_DPX-1300_E.p65
9
9/20/05, 5:07 PM
5 Preparation
Before projection, install the main unit and a screen, connect the main unit to an AV component or computer, and adjust the projection image.
You can begin projection as soon as installation is complete.
Refer to the sections below for information on how to install the main unit to suit your viewing environment.
◆If you have not installed the main unit or screen
• Immediately after purchase, when you have not installed either the main unit or a screen.
• When moving the main unit and screen to a new location.
STEP 1
STEP2
Install the main unit
and screen.
☞ page 12
Connect AV
components or a
computer to the
main unit.
☞ page 15 - 16
STEP3
Select an image and
project.
☞ page 17 - 26
• The image is used
for adjusting the
image position
and focus.
STEP4
Adjust the
projection image.
☞ page 27 - 47
• Use the menu to
adjust projection
details.
Projection
preparations
complete
◆If you have installed the main unit and screen, but not connected
any image playback components
• You have installed the main unit and screen, but not connected any source components.
• You are using the main unit in a previously installed location, and wish to change the component you use as a signal source.
STEP2
Connect AV
components or a
computer to the
main unit.
☞ page 15 - 16
STEP3
Select an image and
project.
☞ page 17 - 26
• The image is used
for adjusting the
image position
and focus.
STEP4
Adjust the
projection image.
☞ page 27 - 47
• Use the menu to
adjust projection
details.
Projection
preparations
complete
◆If you have installed the main unit and screen, and connected a
source component
• You have installed the main unit and screen, and connected source components.
• You are using the main unit in a previously installed location with previously connected source components.
You do not need to carry out step 3 or step 4 if you
do not want to adjust the projection image. If the
unit does not project the image correctly, it may not
be connected correctly. In this case, carry out this
procedure starting from step 2.
STEP3
Select an image and
project.
☞ page 17 - 26
• The image is used
for adjusting the
image position
and focus.
STEP4
Adjust the
projection image.
☞ page 27 - 47
• Use the menu to
adjust projection
details.
10
11_DPX-1300_E.p65
10
9/20/05, 5:07 PM
Projection
preparations
complete
Step1
Set up the projector and screen
• Install the projector
• Install the screen ☞ page 12 - 14
Step2
Connect an AV component or computer
• Connect AV components
• Connect a computer ☞ page 15 - 16
Step3
Turn the power on and selecting an
image for projection
5
Step4
Use the menu to adjust the image quality and
other parameters
Only adjust these
parameters when
necessary. It is not
necessary to adjust these
settings once you have set
them initially.
11
11_DPX-1300_E.p65
11
9/20/05, 5:07 PM
English
• Image quality: Set image quality details
• Signal setting: Set input signal details
• Default settings: Set the default settings for everyday use
• Installation settings: Set to suit your viewing environment ☞ page 27 - 47
Prepararion
• Turn on the projector power
• Begin playback of the input image
• Select an input signal
• Select a projection image aspect
• Adjust the image
Focus/Vertical and Horizontal position/Size/Iris
☞ page 17 - 26
6 Installation
Setting up the DPX-1300
There are four ways of mounting the projector.
Mounting method
Placed on a table
Mounted on the
ceiling
Projection method
A: From in front of a screen
B: From behind a semi-translucent screen
C: From in front of a screen
D: From behind a semi-translucent screen
◆ Mounting the projector on a table
A: From in front of a screen
Place the unit on a table to project and view the image from in front of the screen. Usually,
place the unit on a reasonably high table. The height from the bottom of the unit to the center
of the lens is 12.4 cm (4”-7/8).
B: From behind a screen (using a semi-translucent screen)
Place the unit on a table to project and view the image from behind a semi-translucent
screen. The distance between the projector and the screen should be the same as “A: From in
front of the screen”.
• Set the [Location] menu item in the [Setup] menu group to [Rear/Table]. (☞ page 27 - 47)
◆ Mounting the projector on the ceiling
There are two kinds of brackets (sold separately: PMT-L31 and PMT-H35), which you can use to mount the projector on the ceiling. Please
consult your dealer for details on their use, and have installation done by either your dealer or a reputable contractor.
C: From in front of a screen
Mount the unit on the ceiling to project and view the image from in front of the screen. The
distance between the projector and the screen should be the same as “A: From in front of the
screen”.
• Set the [Location] menu item in the [Setup] menu group to [Front/Ceiling]. (☞ page 27 - 47)
D: From behind a semi-translucent screen
Mount the unit on the ceiling to project and view the image from behind a semi-translucent
screen. The distance between the projector and the screen should be the same as “B: From
behind a screen”.
• Set the [Location] menu item in the [Setup] menu group to [Rear/Ceiling]. (☞ page 27 - 47)
12
11_DPX-1300_E.p65
12
9/20/05, 5:07 PM
Projection distance
The most suitable distance between the screen and the projector (see Projection distance [a]) depends on the size of the screen (diagonal
length) you use. You can use the zoom function to adjust the projection distance within a preset range from Wide to Tele. You can also alter
the V.POS parameter to adjust the vertical position of the image to better suit the screen. Use the information in the table below to determine
the best location to place the projector in to suit your screen size.
<When using a 16:9 screen>
Screen size
(inch)
Projection distance [a]
Wide (m) – Tele (m)
60
70
80
90
100
110
120
150
200
1.78 – 2.88
2.08 – 3.37
2.39 – 3.86
2.70 – 4.35
3.00 – 4.84
3.31 – 5.33
3.62 – 5.82
4.54 – 7.29
6.07 – 9.74
Projection distance [a]
6
80''
100''
Lens
centerline
150''
Installation
60''
200'' Screen size
* These are theoretical values.
During actual use there may be a deviance of a few percent.
<When using a 4:3 screen>
Since the DPX-1300 has a 16:9 panel, the ideal installation location for use with a 4:3 screen depends on the size of the image you wish to
view.
Screen size
(inch)
60
80
100
120
200
Projection distance[a]
16:9 image (*1)
Wide (m) – Tele (m)
4:3 image (*2)
Wide (m) – Tele (m)
1.63 – 2.64
2.19 – 3.54
2.76 – 4.44
3.32 – 5.34
5.58 – 8.94
2.17 – 3.52
2.93 – 4.72
3.68 – 5.92
4.43 – 7.12
7.43 – 11.92
(*3)
13
11_DPX-1300_E.p65
13
9/20/05, 5:07 PM
English
(*1) Projects a 16:9 image that completely fills the screen (leaves a black line at the top and bottom of the screen).
(*2) Projects a 4:3 image that completely fills the screen.
(*3) When projecting both 16:9 and 4:3 images.
You can use the zoom function to make efficient use of the screen for both *1 and *2 above. The projection distance in this case is
between Wide in *2 and Tele in *1. Use the zoom to adjust the size of the projection images so that they fill the screen completely. Note
that adjustments to V.POS may cause the position of the image to change.
Projection image position
Follow the instructions to adjust the position of the projected image on screen.
<Using ZOOM to adjust image position>
Wide
This illustration shows the limits within which the
zoom function can alter projection distance [a] in
relation to screen size. You can adjust the image
within these limits so that it fills the screen
completely. ( ☞ page 26)
Tele
Lens centerline
<Using V.POS (vertical position) to adjust image position>
You can adjust the vertical position of the
projection image up or down by half of the height
of the screen. For example, shifting V.POS fully up
brings the lower limit of the image above the
centerline of the lens. (☞ page 25)
Lens centerline
(When shifted
fully up)
Lens centerline
(When shifted
fully down)
<Using the adjusters to adjust image position>
If you mount this unit on a tabletop, you can use the adjusters on its underside to change the
position of the projection image. Rotate the movable part of the two screw-type adjusters at
the front bottom of the case to adjust the height. The movement range of the adjusters is 3
cm (1-1/4 inch). Adjust with care as loosening them further than 3 cm may cause them to
separate from the unit.
◆ Keystone adjustment
If you mount the unit at an angle to the screen, it projects trapezoidally distorted images. You can use the [V keystone Correction] or [H
keystone Correction] item in the [Setup] menu group to rectify this. (☞ page 36)
Memo
•
If the keystone is adjusted aspect ratio may not be correctly maintained. To correctly maintain the aspect ratio, try to use the DPX1300 with the lens shift in the center position.
•
The video may be disturbed by keystone correction. Wherever possible, we recommend setting up so the screen and projector
form a right angle.
14
11_DPX-1300_E.p65
14
9/20/05, 5:07 PM
7 Connection
Connecting to AV components
This unit is equipped with 7 types of video input jacks for AV components. Follow the diagram to connect AV components to this unit, taking
care to use cables and adapters that match the input jacks.
Signal type
Composite video
S-Video
Component video/RGB video
Component video/RGB video
Component video
Component video/RGB video (digital)
RGB video (digital)
Input
VIDEO
S VIDEO
INPUT A
INPUT B
D4 VIDEO
HDMI
DVI
Connector type
Pin jack
Mini DIN connector
BNC connector x 3-5
D-sub 15 pin
D connector
HDMI connector
DVI connector
Warning
•
Be sure to turn off the power of this unit and the source component before attempting connection.
•
Connection methods and jack names may differ depending on the component you are attempting to connect. Refer to the owner’s
manual for the component.
•
Insert all plugs firmly to avoid noise or other problems.
HDMI cable (digital)
DVI cable (digital)
OUT
HDMI
DVI
IN
REMOTE
RS-232C
TRIGGER OUT
INPUT A
INPUT B
D4 VIDEO
RGB/YPBPR/YCBCR
B/PB/CB
R/PR/CR
HD/SYNC
VD
S VIDEO
7
VIDEO
BNC cable for
component connection
Connection
D-sub
monitor
cable
G/Y
Video pin cable
S-Video cable
Pin/BNC
adapters
Pin cable
D connector
cable
G/Y
HDMI
output
connector
DVI output
connector
D1—4
output
connectors
D-sub
Pin jacks
B/PB/CB
R/PR/CR
BNC jacks
S-Video output
jack
Video output
jack
Component/RGB video output connectors
Image output from AV components
Memo
•
15
11_DPX-1300_E.p65
15
9/20/05, 5:07 PM
English
Be sure to connect Y/PB/PR and Y/CB/CR to the jacks with the correct signals when connecting AV components to INPUT A. Refer to
the owner’s manual of the source component for more information. You may need to make connections to HD/SYNC and VD for
RGB video signals.
Connecting to computer devices
You can use the following three methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and
jacks you wish to use. The HDMI terminal does not support PC signals.
Input
Signal type
RGB (Analog)
RGB (Analog)
RGB (Digital)
INPUT A
INPUT B
DVI
Connector type
BNC jack x 5
D-sub 15 pin
DVI connector
OUT
DVI
HDMI
RGB/YPBPR/YCBCR
IN
REMOTE
RS-232C
TRIGGER OUT
INPUT A
INPUT B
D4 VIDEO
G/Y
D-Sub monitor
cable
B/PB/CB
R/PR/CR
HD/SYNC
VD
S VIDEO
VIDEO
BNC monitor cable
Monitor output terminal
DVI cable
Computer devices
16
11_DPX-1300_E.p65
16
9/20/05, 5:07 PM
8 Projection
Checking installation and connections
◆ Pre-operation check
Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using.
However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time
you used this unit. Check settings and connections only when the unit does not appear to project images correctly.
Prior to projection, check that the main unit and screen are correctly installed, and that source components are connected correctly.
Is the main unit power
turned on?
Main unit
Is the screen installed correctly?
“Setting up the DPX-1300”
☞ page 12
Are the components connected correctly?
“Connecting to AV components”
☞ page 15 - 16
Image source component
PURE DIRECT
VOLUME
REC OUT/ZONE 2
MULTI JOG
SOURCE/REMOTE
2CH/MULTI CH
DTV/LD
CABLE
SPEAKERS
A
B
DVD
MD/TAPE
CD-R
SAT
INPUT SELECTOR
INPUT MODE
MULTI CH
INPUT
STRAIGHT
TUNER
BALANCE
DSP
PROGRAM
CD
VCR 1
VCR 2
TONE
CONTROL
EFFECT
PHONO
DVR
VIDEO AUX
STANDBY
/ON
SILENT
VIDEO AUX
OPTIMIZER
MIC
PHONES
S VIDEO
VIDEO
L
AUDIO
R
Is the source component power
turned on?
OPTICAL
To project images, carry out the following procedure.
8
Projection
Check installation and connections
Select an image for projection and image adjustment
Turn on the projector power.
Begin playback of the source image for adjustment.
Select a projection image.
(Select an input signal and projection image aspect.)
Adjust focus and vertical/ horizontal positioning.
Projection preparations complete
For an explanation of detailed settings, see “Menu”. ☞ page 27 - 47
English
17
12_DPX-1300_E.p65
17
9/20/05, 5:07 PM
Turning the projector power on
◆ Turning the power on
Always remove the lens cap before operating the main unit.
STANDBY/ON
STANDBY/ON
indicator
MENU
ESCAPE
PATTERN
SETTING
ASPECT
The STANDBY/ON indicator lights red.
INPUT
LAMP
COVER
TEMP
FAN
OUT
DVI
HDMI
IN
RS-232C
REMOTE
TRIGGER OUT
INPUT A
INPUT B
RGB/YPBPR/YCBCR
1. Insert the supplied power cable
firmly into the AC inlet at the rear
of the main unit, then insert the
plug into an AC outlet.
D4 VIDEO
G/Y
B/PB/CB
R/PR/CR
HD/SYNC
VD
S-VIDEO
VIDEO
AC inlet
button
STANDBY/ON button
2. Press the STANDBY/ON button
button on the remote
(the
control).
AUTO
STANDBY/ON
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
MENU
ESCAPE
ESCAPE
MENU
PATTERN
SETTING
ASPECT
ASPECT
INPUT
LAMP
INPUT
Remote Control
The indicator blinks green and the lamp
lights up in preparation for projection. After
approximately 35 seconds, the indicator
changes from blinking to steady green,
indicating that the unit is ready to project.
COVER
TEMP
FAN
Main unit
Warning
•
Do not remove the power cable while the STANDBY/ON indicator is blinking green or
lit steady green. This could damage the lamp or reduce lamp life.
18
12_DPX-1300_E.p65
18
9/20/05, 5:07 PM
Turning the projector power on
◆ Placing the DPX-1300 in standby mode
button
STANDBY/ON button
A confirmation message appears on the
screen.
AUTO
STANDBY/ON
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
1. Press the STANDBY/ON button.
Press again to enter standby.
MENU
ESCAPE
MENU
ESCAPE
PATTERN
SETTING
ASPECT
INPUT
LAMP
INPUT
ASPECT
Remote Control
COVER
TEMP
FAN
Main unit
2. If you wish to place the DPX-1300
in standby mode, press the
STANDBY/ON button again.
The lamp changes to a half lit state, and the
fan activates for 2 minutes to cool the lamp.
During this time, the STANDBY/ON
indicator blinks red, and pressing
STANDBY/ON does not turn main unit
power on again. When the unit finishes
cooling, the fan stops, and the STANDBY/
ON indicator turns red.
Memo
•
The lamp may blink when half lit. This is not a defect.
8
Warning
AC inlet
HDMI
•
This unit is not disconnected from the AC power source as long as it is connected
to the AC outlet, even if this unit itself is turned off by STANDBY/ON.This state is
called the standby mode. In this state, this unit is designed to consume a very small
quantity of power.
•
If you do not plan to use the main unit for a long period of time, attach the lens cap
and remove the plug from the AC outlet.
•
Condensation may appear on the unit if the temperature of the surrounding
environment changes quickly. Condensation may also cause the projected image to
be cloudy. Place the unit in standby mode until the condensation disappears.
Switching the unit on when condensation is present may damage the unit.
IN
REMOTE
RS-232C
TRIGGER OUT
INPUT A
INPUT B
RGB/YPBPR/YCBCR
Do not remove the power cable while the STANDBY/ON indicator is blinking green
or when the fan is activated. This could damage the lamp or reduce lamp life.
D4 VIDEO
G/Y
B/PB/CB
R/PR/CR
HD/SYNC
VD
S-VIDEO
VIDEO
Projection
OUT
DVI
•
English
19
12_DPX-1300_E.p65
19
9/20/05, 5:07 PM
Selecting an input signal
◆ Selecting using the INPUT button
Press the INPUT button to select an input signal from a source component. Choose from the following:
INPUT SIGNAL
Projection image signal
VIDEO
Selects component video signals received from AV components connected to the VIDEO jack.
S VIDEO
Selects S-Video signals received from AV components connected to the S VIDEO jack.
INPUT A
• Component
• RGB PC
• RGB TV
: Selects component signals received from the INPUT A BNC jacks.
: Selects RGB signals received from computers connected to the INPUT A BNC jacks.
: Selects RGB signals received from AV components connected to the INPUT A BNC jacks.
INPUT B
• Component
• RGB PC
• RGB TV
: Selects component signals received from the INPUT B D-sub 15 pin jack.
: Selects RGB signals received from computers connected to the INPUT B D-sub 15 pin jack.
: Selects RGB signals received from AV components connected to the INPUT B D-sub 15 pin jack.
HDMI
• Auto
• Component
• RGB TV
: Signals input to the HDMI jack from AV components (automatically distinguishes between
component and RGB signals).
: Selects digital component signals received from AV components connected to the HDMI jack.
: Selects digital RGB signals received from AV components connected to the HDMI jack.
DVI
• RGB PC
• RGB TV
: Selects RGB signals received from computers connected to the DVI jack.
: Selects RGB signals received from AV components connected to the DVI jack.
D4 VIDEO
Selects component signals received from AV components connected to the D4 VIDEO jack.
20
12_DPX-1300_E.p65
20
9/20/05, 5:07 PM
Selecting an input signal
<Using the INPUT button to select a signal>
Remote cotrol
Main unit
1. Press the INPUT button.
+ button
STANDBY/ON
ZOOM
FOCUS
IRIS
SETTING
PATT
VIDEO
The input signal selection menu appears on
the display.
AUTO
V. POS
Input signal
S VIDEO
INPUT A
INPUT B
ESCAPE
MENU
HDMI
MENU
ESCAPE
PATTERN
DVI
SETTING
button
ASPECT
D4
INPUT
LAMP
COVER
TEMP
FAN
INPUT
ASPECT
RESET
HIDE
LIGHT
STILL
INPUT
S VIDEO
VIDEO
A
HDMI
B
DVI
INPUT button
2. Use the h or g buttons to select
an input signal, then press the
button.
Input signal
VIDEO
S VIDEO
INPUT A
D4
MEMORY
1
2
3
4
5
6
INPUT B
HDMI
DVI
D4
Cursor button
Warning
•
You can select [Component], [RGB PC], or [RGB TV] for INPUT A and INPUT B, or
[Auto], [Component], or [RGB TV] for HDMI, from the submenu. If you do not select a
setting, the unit continues to use the setting from the last signal it received. To
change this setting, carry out the following procedure.
3. Press the + button to open the
submenu.
Input signal
VIDEO
S VIDEO
INPUT A
8
INPUT B
DVI
D4
The mark to the right of the input signal
name indicates that there is a submenu
available for selection.
4. Select an appropriate setting
from [Component], [RGB PC], or
[RGB TV] and press the
button
to confirm the setting.
Projection
HDMI
Input signal
VIDEO
S VIDEO
INPUT A
Component
INPUT B
RGB PC
HDMI
RGB TV
DVI
D4
Memo
•
If you set your laptop or notebook computer to display on its built-in display and on
an external monitor simultaneously, the main unit may not project the image
correctly. In this case, set your computer to display on the external monitor only.
Refer to your computer’s operating instructions for further details.
English
21
12_DPX-1300_E.p65
21
9/20/05, 5:07 PM
Selecting an input signal
◆ Selecting a display aspect for a projection image
The display aspect parameter sets the ratio of height to width the unit uses to project an image for an input signal.
Remote cotrol
Main unit
1. Press the ASPECT button.
The display aspect selection menu appears
on the display.
cursor button
AUTO
STANDBY/ON
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
Display Aspect Ratio
Normal
Squeeze
Smart Zoom
ESCAPE
MENU
Zoom
MENU
ESCAPE
Auto
PATTERN
Special
SETTING
ASPECT
Through
INPUT
LAMP
COVER
TEMP
FAN
INPUT
ASPECT
RESET
HIDE
LIGHT
STILL
INPUT
S VIDEO
A
HDMI
VIDEO
B
DVI
ASPECT
button
button
D4
MEMORY
1
2
3
4
5
6
2. Use the h or g button
to select a suitable display aspect
button.
setting, then press the
If you select [Special] or [Through],
pressing the + button displays the submenu.
Display Aspect Ratio
Auto
Normal
Squeeze
Smart Zoom
Zoom
Special
Through
Memo
•
The display aspect you can use depends on the current input signal. When the input
signal contains display aspect information, set the display aspect parameter to
[Auto] to detect the appropriate display aspect setting automatically.
•
You can also use the [Display Aspect Ratio] page in the menu screen to select a
display aspect. (☞ page 27- 47)
22
12_DPX-1300_E.p65
22
9/20/05, 5:07 PM
Selecting an input signal
<Display aspect types>
Memo
•
Refer to the glossary for explanations of terms such “letterbox” or “squeeze”. (☞ page 55)
Auto
Special
Detects information encoded in letterbox or squeeze type input
signals and automatically selects an appropriate display aspect.
Depending on the input source, the unit may not change to the
most appropriate mode. In this case, manually select a suitable
setting.
Normal
Projects images with their original display aspect. Depending
on the input signal, black areas may appear to the left and right
of the image.
Squeeze
Returns horizontally compressed images to their original
aspect. Use this mode to display horizontally squeezed images
in a normal wide aspect manner.
Smart Zoom
Stretches the left and right edges of a 4:3 image without
altering the image center, to project a 16:9 image that fills the
screen.
Subtitle Zoom
The best format for projecting subtitled letterbox format
software. See page 45 for the operational procedure.
• Subtitle area: Adjust the area used to display subtitles on
screen.
• V Scroll: Adjusts the vertical position of the subtitles.
Cinema Zoom
Removes the black bar from Cinescope size screens (2.35:1) to
display a full horizontal image, cutting both screen sides.
There are two types: SDTV for 4:3 images, and HDTV for
16:9 images.
Cinema Squeeze
Removes the black bar from cinescope size screens for 4:3
images and resize the vertical image so that a 16:9 panel
resolution is fully displayed, cutting both screen sides.
14:9 Zoom
Displays 14:9 images with a full vertical aspect, retaining the
black area at either side of the screen.
Through
Zoom
Projects images the unit receives in letterbox format as 16:9
images that fill the screen.
Normal Through
Projects images without stretching or reducing them. The size
of the projection image depends on the resolution of the image
received.
Projection
Squeeze Through
Widens the image received to project it with a 16:9 aspect
ratio. The size of the projection image depends on the
resolution of the image received. This mode is not available for
RGB PC input signals.
8
English
23
12_DPX-1300_E.p65
23
9/20/05, 5:07 PM
Selecting an input signal
<Representative examples>
Input signal type
Input image
Display aspect
Projected image
Normal
Standard 4:3 image
Smart Zoom
Zoom
Letter box
Subtitle Zoom
SUBTITLE
Cinema Zoom
Squeeze
Squeeze
Squeeze
Cinema Squeeze
14:9 image
14:9 Zoom
Normal
Normal
Cinema
Scope
Cinema Zoom
HDMI
RGB PC
Normal
Normal
Normal Through
Squeeze
Squeeze Through
All
24
12_DPX-1300_E.p65
24
9/20/05, 5:07 PM
Adjusting the image
Carry out the following adjustments to obtain optimal projection conditions.
◆ Using test patterns to adjust the projection image – PATT button
The DPX-1300 is equipped with three test patterns, the crosshatch pattern necessary for focus and keystone adjustment, and the grayscale
and color bar patterns necessary for adjusting image quality.
1. Press the PATT button on the
remote control, or the PATTERN
button on the main unit.
AUTO
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
PATT
button
2. Press the + or - button to select
the necessary pattern.
MENU
ESCAPE
Crosshatch pattern
Grayscale pattern
3. To exit from the test display,
press the PATT or PATTERN
button.
STANDBY/ON
PATTERN button
MENU
ESCAPE
PATTERN
Color bar pattern
SETTING
ASPECT
INPUT
LAMP
COVER
TEMP
FAN
◆ Adjusting the vertical position – V.POS button
If the center of the screen is not in line with the center of the lens of the DPX-1300, use the V.POS button to adjust the position of the image
up or down. You can adjust the image to a maximum of half of the height of the projection screen.
AUTO
V.POS
button
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
MENU
ESCAPE
ESCAPE button
MENU
PATTERN
SETTING
button
SETTING
ASPECT
Lens Shift
2. Press the h or g button to move
the projected image to a suitable
place.
STANDBY/ON
ESCAPE
8
Projection
1. Press the V.POS button on the
remote control, or press the
SETTING button on the main unit
repeatedly to select [Lens Shift]
from the display menu.
3. To exit from the adjustment
mode, press the V.POS or
ESCAPE button.
INPUT
LAMP
COVER
TEMP
FAN
English
25
12_DPX-1300_E.p65
25
9/20/05, 5:07 PM
Adjusting the image
◆ Adjusting the size of an image – ZOOM button
Enlarge or reduce the size of the projection image to match the size of the screen. The zoom ratio is 1:1.6.
ZOOM
button
1. Press the ZOOM button on the
remote control, or press the
SETTING button on the main unit
repeatedly to select [Zoom] from
the display menu.
AUTO
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
MENU
ESCAPE
STANDBY/ON
ESCAPE button
MENU
ESCAPE
Zoom
2. Press the h or g button to adjust
the image to a suitable size.
PATTERN
SETTING
button
3. To exit from the adjustment
mode, press the ZOOM or
ESCAPE buttons.
SETTING
ASPECT
INPUT
LAMP
COVER
TEMP
FAN
◆ Adjusting the image focus – FOCUS button
Adjust the focus of the on-screen image.
AUTO
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
FOCUS
button
1. Press the FOCUS button on the
remote control, or press the
SETTING button on the main unit
repeatedly to select [FOCUS]
from the display menu.
Focus
MENU
ESCAPE
Memo
STANDBY/ON
•
ESCAPE button
MENU
ESCAPE
PATTERN
SETTING
button
SETTING
ASPECT
2. Press the h or g button to adjust
the focus of the projected image.
INPUT
LAMP
COVER
TEMP
When you want to use the test pattern
to adjust image focus press the PATT
button on the remote control, or the
PATTERN button on the main unit
before carrying out step 1.
FAN
3. To exit from the adjustment
mode, press the FOCUS or
ESCAPE buttons.
◆ Adjusting the iris setting – IRIS button
Press the g button to reduce the aperture of the iris for increased black levels and contrast, or the h button to increase aperture to obtain a
brighter image.
1. Press the IRIS button on the
remote control, or press the
SETTING button on the main unit
repeatedly to select [IRIS] from
the display menu.
AUTO
IRIS
button
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
MENU
ESCAPE
2.
STANDBY/ON
Press the h or g button to adjust
the iris setting for the projected
image.
ESCAPE button
MENU
ESCAPE
PATTERN
SETTING
button
SETTING
ASPECT
3. To exit from the adjustment
mode, press the IRIS or ESCAPE
button.
INPUT
LAMP
COVER
TEMP
FAN
26
12_DPX-1300_E.p65
26
9/20/05, 5:07 PM
Iris
9 Menu
Menu configurations
Configure the DPX-1300 to suit your viewing environment by adjusting image quality, initial settings, defaults, and setup characteristics.
These parameters can be accessed through the menu.
Press the MENU button on the remote control or the main unit to display the menu screen. The menu consists of the [Image], [Signal],
[Initial], and [Setup] menu groups, each containing numerous items you can use for configuring the unit. Note that some items are only
selectable for certain types of input signal (Video, Component, RGB TV, RGB PC).
Menu groups appear in the upper area of the display, as the top level of menu composition. Menu items appear in the left area of the display.
You can select settings and make adjustments to suit your preferences. See page 38 - 47 for an explanation of how to use the menu.
◆ Menu screen
<Example: When in Image menu>
Menu group
[Image] selected.
Image
Signal
Initial
Black Level
0
White Level
0
Gamma
Hue
Menu items
Items displayed here depend on
the menu group you select.
The picture on the right shows
menu items in the [Image] group
for example.
[Move Menu Window] area
Use this selection area to move
menu screens. See page 44 for
more information.
Move Menu Window
a
Setup
b
c
d
e
0
Saturation
0
Sharpness Gain
2
Sharpness Type
2
Color Adjustment
White Peaking
Parameter adjustment area
+0.000uv
6500K -
WRGB
0
Iris
Level Adjustment
Menu operation guide
Displays helpful instructions when
special operations are necessary.
Memory 1
Input jack display area
Shows the currently selected
input jack.
VIDEO
Memory number status
Displays the currently selected memory number and memory status. Change
the memory number and lock/unlock memory settings here(☞ page 48-50).
Some menu items contain an additional level of items called a submenu. Moving the cursor to an item with a submenu attached displays “ ”
to the right of the item name. Some submenus contain further levels of submenus containing items for selection.
Menu
<Display example: [Color Adjustment] item submenu>
Move Menu Window
0
White Level
0
Gamma
Saturation
Image
Indicates the existence of a submenu
Initial
0
Color Temp.
b
c
d
0.4
0
2
2
Color Adjustment
Setup
6900K +–0.005uv
y
e
100
Sharpness Type
0.35
0.5
+0.02uv
Standard
+0.000uv
6700K -
0
Iris
Level Adjustment
+ : Enter
Signal
y
a
Sharpness Gain
White Peaking
Setup
5000
Black Level
Hue
Move Menu Window
Initial
6000
Signal
10000
9000
8000
7000
Image
9
Color Adjustment
WRGB
+0.000uv
6700K +0.000uv
6500K -
WRGBYCM
+0.000uv
6500K -
Standard
0.3
0.0
+0.00uv
–
-0.02uv
0.0
0.5
x
0.25
0.25
0.3 x
0.35
[Color Adjustment] submenu
Memory 1
VIDEO
: Edit
Memory 1
VIDEO
[WRGB] submenu
In this example, the menu contains three submenus, and one of the submenus contains a further submenu.
English
27
13_DPX-1300_E.p65
27
9/20/05, 5:07 PM
Menu items
◆ Menu item list:
● Image
● Signal
Black Level (Brightness)
While Level (Contrast)
Gamma
Hue
Saturation
Sharpness Gain
Sharpness Type
Color Adjustment
White Peaking
Iris
Level Adjustment
1
2
Display Aspect Ratio
Overscan
3D Y/C separation
Progressive Mode
Color Space Conversion
Setup Level
Overshoot Supp. Range
Overshoot Supp. Level
Noise Reduction Type
Noise Reduction Level
Horiz. Display Position
Vert. Display Position
Signal Level
Signal Status
● Initial
3
● Setup
Color System
INPUT A Signal
INPUT A Sync Type
INPUT B Signal
INPUT B Sync Type
HDMI Signal
DVI Signal
Auto Power Off
Auto Input Search
Display Language
Lamp Running Time
Reset
5
6
7
6
7
8
6
9
10
11
4
Memo
• Menu items you can choose may differ depending on the input signal type.
• Items in the menu that contain submenus are marked with “
”.
28
13_DPX-1300_E.p65
28
9/20/05, 5:07 PM
Location
V Keystone Correction
H Keystone Correction
Remote Control Sensor
Remote Control ID
Lens Adjustment Lock
Lamp Power
Menu Color
Message
Trigger Out
Baud Rate
12
13
14
15
16
17
Menu items
<Submenu Items>
The submenus display different items depending on the input signal. Items in submenus that contain further submenus are marked with “
● Image
● Setup
● Signal
1: Color Adjustment
Standard
1
2
WRGB
WRGBYCM
3
2: Level Adjustment
YPbPr
RGB
Y Offset
R Offset
Pb Offset
G Offset
Pr Offset
B Offset
Y Gain
R Gain
Pb Gain
G Gain
Pr Gain
B Gain
3: Display Aspect Ratio
Auto
Normal
Squeeze
Smart Zoom
Zoom
Special
4
Through
5
4: Signal Status
Resolution
Sync Type
Sync Polarity
Frequency
Source Equipment (HDMI only)
● Initial
7: Input A/B Sync Type
Auto
Separate Sync
Composite Sync
Sync On Green
8: HDMI Signal
Auto
Component
RGB TV
9: Display Language
English
Deutsch
Español
Français
Italiano
Portuguêsa
10: Lamp Running Time
No
Yes
11: Reset
All Settings
All Memory
Current Memory
12: Location
Front/Table
Front/Ceiling
Rear/Table
Rear/Ceiling
13: Remote Control Sensor
Front & Rear
Front
Rear
Off
14: Remote Control ID
ID 1
ID 2
15: Menu Color
Monotone
6
Color
7
16: Trigger Out
Lamp
Fan
RS-232C
17: Baud Rate
9600bps
19200bps
38400bps
57600bps
115200bps
<Lower level menu items>
1 Standard
4 Special
6 Monotone
• Color Temp.
• Subtitle Zoom
Subtitle Area
V Scroll
• Cinema Zoom
• Cinema Squeeze
• 14:9 Zoom
• Menu Brightness
• Menu Contrast
2 WRGB
• Color selection screen
Color coordinate
Gain
5 Through
3 WRGBYCM
9
Menu
5: Color System
Auto
NTSC
NTSC4.43
PAL
PAL-M
PAL-N
PAL60
SECAM
6: Input A/B, DVI Signals
Component
RGB PC
RGB TV .etc
”.
7 Color
• Menu Brightness
• Menu Contrast
• Color Style
(For video type input signal)
• Normal Through
• Squeeze Through
• Color selection screen
Color coordinate
Gain
Memo
In addition to color temperature adjustment, the color coordinates and gain adjustment for each color may be carried out at the
[WRGB] and [WRGBYCM] color selection screen. Refer to page 42 and 43 for more information.
•
You can select [Subtitle Area] and [V Scroll] from the [Subtitle Zoom] menu item. See page 45 and 46 for more information.
English
•
29
13_DPX-1300_E.p65
29
9/20/05, 5:07 PM
Menu items
◆ Menu group items and functions
<Image>
You can adjust the image when the unit is receiving an input signal.
Black Level
(Input signal)
Video/S-Video/Component/RGB TV
White Level
(Input signal)
Video/S-Video/Component/RGB TV
Adjusts the level of darkness (black level) in an image.
Adjusts the level of darkness without altering peak whiteness levels.
• + side (0 to +50):
White
Increases the luminance of dark scenes,
increasing the clarity of shading, but
reducing contrast.
Output signal
• - side (-50 to 0):
Weakens dark scenes, increasing image
contrast while reducing the clarity of black
shading.
Black
Adjusts the bright areas (white level) in the image.
Changes the brightness of an image without altering the brightness of the black areas of the
image.
• + side (0 to +50):
White
Increases the brightness of white areas in
the image, increasing contrast clarity, but
rendering white shadings difficult to see.
Output signal
• - side (-50 to 0):
Reduces the contrast of images.
Black
Brightness
Input signal White
Input signal White
Adjusts the overall brightness of the image.
• Increase luminance (0 to +50):
White
Setting this figure too high results in a
white saturated image without any black.
• Decrease luminance (-50 to 0)
Output signal
Setting this figure too low darkens the
entire image.
(Input signal)
RGB PC
Black
Contrast
Input signal White
Adjusts the bright areas (white level) in the image.
Changes the brightness of an image without altering the brightness of the black areas of the
image.
white level
• + side (1.00 to 1.50):
White
Increases the brightness of white areas in
the image, increasing contrast clarity, but
rendering white shadings difficult to see.
Output signal
• - side (0.50 to 1.00):
Reduces the contrast of images.
(Input signal)
RGB PC
Black
Input signal White
Gamma
Changes the way the unit responds to changes in the shadings and color
(Input signal)
Video/S-Video/Component/RGB TV/RGB PC
tones of the image.
The unit supplies 10 types of patterns for dealing with these changes. (☞ page 46)
• A-E Provides the same sense of contrast as an ordinary TV monitor. Dark sections
become more muted in the order A
E.
• a-e
Provides richer expression of gradations in dark sections. Dark sections become
e.
more muted in the order a
30
13_DPX-1300_E.p65
30
9/20/05, 5:08 PM
Menu items
Hue
(Input signal)
Video/S-Video/Component/RGB TV
Saturation
(Input signal)
Video/S-Video/Component/RGB TV
Sharpness Gain
Sets the hue or phase of the image.
• + side (0 to +50) : Shifts the hue towards blue coloration.
• - side (-50 to 0) : Shifts the hue towards red coloration.
Adjusts the degree to which color depth is expressed in the image.
• + side (+100 to + 150) : The unit projects colors with greater depth.
• - side (+50 to +100)
: The unit projects colors with less depth.
(Input signal)
Video/S-Video/Component/RGB TV
Adjusts the clearness of the image edges.
Increase this figure to render a sharper image or reduce it to give a softer image with less
image noise.
Choices: 0 to 20
Sharpness Type
Changes the characteristics of the filter used for “Sharpness Gain”
(Input signal)
Video/S-Video/Component/RGB TV
(described above).
When setting the [Sharpness Gain] parameter to render a relatively strong image (closer to
20), increase this figure to enhance clearness of the image or reduce this figure to enhance
softness of the image.
You cannot adjust this parameter if [Sharpness Gain] is set to [0].
Choices: 1 to 20
Color Adjustment
Adjusts color balance.
There are three menus, [Standard], [WRGB], and [WRGBYCM], separated in order of
complexity from simple to detailed. By the default setting, the DPX-1300 automatically
selects BT709 (RGB color coordinate for High-Definition Television) for HDTV (HighDefinition Television) or PC video input and BT601 (RGB color coordinate for Standard
Television) for SDTV (Standard Television) input. Refer to page 42 for parameter operation
methods.
The present color temperature setting is displayed to the right of the menu items.
+0.000uv
Color Adjustment
Standard
6700K The current color temperature is displayed.
(Input signal)
Video/S-Video/Component/
RGB TV/RGB PC/D4 VIDEO
y
9
0.5
0.0
W (Color
temperature
and h UV)
0.0
0.5
Menu
- Standard
Adjusts color temperature and hUV
only. hUV adjusts values within the
maximum color temperature limits of the
projector.
x
Color Temp.
(Input signal)
Video/S-Video/Component/RGB TV/RGB PC
Adjusts color temperature.
Adjusts the level of white in colors between red
and blue, and between green and magenta.
Increase the color temperature to increase the
amount of blue in an image, giving bright color
tones. Reduce the color temperature to increase
the amount of red, giving a darker, more relaxed
atmosphere to the image.
Choices: 5,000 to 10,000
White Correction
(Input signal)
Video/S-Video/Component/RGB TV/RGB PC
hUV
English
Adjusts hUV.
Increasing the hUV setting increases the amount
of green in the image. Decreasing this setting
increases the amount of magenta.
Choices: -0.02 to +0.02
Color temprature
adjustment
+
–
31
13_DPX-1300_E.p65
31
9/20/05, 5:08 PM
Menu items
Color Adjustment
(continued)
(Input signal)
Video/S-Video/Component/
RGB TV/RGB PC/D4 VIDEO
- WRGB
Adjusts the color temperature, the color
coordinates and gain for the three primary
colors, R(Red), G(Green), and B(Blue).
The unit sets the complemental colors
Y(Yellow), C(Cyan), and M(Magenta)
automatically. Adjusting [Color Temp.]
resets the RGB gain based on color
coordinate settings. Adjusting [Gain] resets
[Color temp.] based on color coordinate
settings. Use the color temperature fixed
mode if you want to adjust the RGB
coordinates while keeping the color
temperature setting unchanged. Refer to
“ Example: Using the color temperature
fixed mode” on page 43 for operation
methods.
y
G (Green)
0.5
W (Color temperature
and h UV)
R (Red)
0.0
- WRGBYCM
Adjusts the color coordinates and gain
for each component color individually.
When you have selected WRGBYCM
in the color adjustment submenu, press
RESET to automatically adjust the
RGB gain and YCM color balance to
the most appropriate setting, based on
color temp and RGB color balance
settings.
B (Blue)
0.0
0.5
x
y
G (Green)
Y (Yelow)
C (Cyan)
0.5
W (Color temperature
and h UV)
R (Red)
0.0
M (Magenta)
0.0
0.5
x
B (Blue)
Choices: White correction : -0.02 to +0.02
Color temperature : 5,000 to 10,000
Gain
: 0.00 to 1.99
White Peaking
Enhances the brilliance of the white portions of the projected image.
Choices: 0 to 5
Iris
Adjusts the iris (Optical).
You can select 3 levels.
(Input signal)
Video/S-Video/Component/RGB TV/RGB PC
Level Adjustment
(Input signal)
Component/RGB TV/RGB PC
Close
Open
Adjusts the analog input signal gain and offset settings.
Adjust the gain and offset for component and RGB (Y, CB, CR/R, G, B) input signals.
Choices: -50 to 0 to +50 (except for HDMI signals)
32
13_DPX-1300_E.p65
32
9/20/05, 5:08 PM
Menu items
◆ Signal
You can adjust the image when the unit is receiving an input signal.
Display Aspect Ratio
(Input signal)
Video/S-Video/Component/RGB TV/RGB PC
Overscan
(Input signal)
Video/S-Video/Component/RGB TV
3D Y/C Separation
(Input signal)
Video(NTSC)
Progressive Mode
(Input signal)
Video/S-Video/Component/RGB TV
Color Space Conversion
(Input signal)
Video/S-Video/Component
(Input signal)
Video/S-Video/Component/RGB TV
Overscans video input sources for display.
Selects from [Standard] and [Full]. This parameter is not available when you select [Smart
Zoom] in [Display Aspect]. In some cases, noise may appear at the edges of the image
when you select [Full].
• [Standard] : approximately 94% video output ratio
• [Full]
: approximately 100% video output ratio
Adjusts the quality of images input from VIDEO jack.
Suppresses the rainbow-like color and annoying dots in images. This function is only
available for NTSC format signals the unit receives at its composite input jacks.
Choices: On/Off
Switches the interlace/progressive (I/P) conversion mode.
(Only for interlaced TV signal).
• [Auto] : Detects the video, film and computer graphics (CG) contents and converts into
optimized progressive frames automatically.
• [Video] : Force to convert using motion-adaptive I/P conversion for video contents only.
• [Film] : Force to convert using pulldown I/P conversion for film or CG contents
only. Not recommended to use this mode unless a content consists of the
progressive frames clearly.
Selects color space coefficients.
• [Auto] : Selects the best color space coefficient for the image resolution.
• [SDTV] : Color space coefficient for BT.601 type signal.
• [HDTV] : Color space coefficient for BT.709 type signal.
9
Compensates for differences in the black levels of images.
• For signals equal to the pedestal level : Set to [0%].
• For signals with high levels of blackness : Set to [7.5%].
Menu
Setup Level
Sets the aspect ratio for projecting an image from an input signal.
See “Selecting a display aspect for projecting images”, page 22.
%
100
0
PEDESTAL LEVEL
BLACK LEVEL
English
33
13_DPX-1300_E.p65
33
9/20/05, 5:08 PM
Menu items
Overshoot Supp. Range
Adjusts the range of the overshoot surpression in the outline of the
(Input signal)
Video/S-Video/Component/RGB TV
projected images.
This function is only available for SDTV and EDTV.
Choices: 1 to 5
Overshoot Supp. Level
Adjusts the level of the overshoot surpression in the outline of the projected
(Input signal)
Video/S-Video/Component/RGB TV
images.
This function is only available for SDTV and EDTV.
Choices: Off/1/2/3
Noise Reduction Type
Reduces noise in the images.
Digital processing eliminates noise in the luminance and color signals from sources with a
comparatively large amount of noise, producing a more vivid image. Use when the quality
of th sources you are viewing requres it.
Choices: Off/3DNR/DVNR
• [3DNR] :3D Noise Reduction
This function is only available for SDTV, EDTV, and HDTV.
Reduces noise in the luminance and color signals and random noise by pixel
unit.
• [DVNR] :Digital Video Noise Reduction
This function is only available for SDTV.
Reduces mosquito noise and block noise caused by compression of the digital
video images.
(Input signal)
Video/S-Video/Component/RGB TV
Noise Reduction Level
(Input signal)
Video/S-Video/Component/RGB TV
Horiz. Display Position
(Input signal)
RGB PC /Component/RGB TV
(except for HDMI/DVI signals)
Vert. Display Position
(Input signal)
RGB PC/Component/RGB TV
(except for HDMI/DVI signals)
Adjust the level of the noise reduction.
Choices: 1/2/3/4
Adjusts the horizontal display position of the image.
Choices: -10 to 0 to +10
Adjusts the vertical display position of the image.
Choices: -5 to 0 to +5
Signal Level
Select the range of the black level and white level in the input signal for HDMI
(Input signal)
RGB TV (HDMI/DVI signals only)
and DVI signals.
This function is only available when RGB TV is selected.
Choices: 16 to 235/0 to 255
Signal Status
Displays the resolution of the image signal the unit is receiving.
Sync signal information for RGB type inputs is also displayed.
34
13_DPX-1300_E.p65
34
9/20/05, 5:08 PM
Menu items
◆ Initial
Color System
Selects the color system to use for video input signals.
Usually, set this parameter to Auto to have the unit automatically detect the signal and
select an appropriate color system. Set the unit manually to view NTSC4.43 images as it
cannot detect NTSC4.43 automatically.
Choices: Auto/NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM
INPUT A Signal
Selects the type of input signal received at INPUT A.
Choices: Component/RGB PC/RGB TV
INPUT A Sync Type
Selects the sync type for signals received at INPUT A.
This function is only available for RGB TV.
Choices: Auto/Separate Sync/Composite Sync/Sync on Green
INPUT B Signal
Selects the signal type received at INPUT B.
Choices: Component/RGB PC/RGB TV
INPUT B Sync Type
Selects the sync type for signals received at INPUT B.
This function is only available for RGB TV.
Choices: Auto/Separate Sync/Composite Sync/Sync on Green
HDMI Signal
Selects the signal type received at the HDMI jack.
Choices: Auto/Component/RGB TV
DVI Signal
Selects the signal type received at the DVI jack.
Choices: RGB PC/RGB TV
Auto Power Off
If the signal the unit is currently receiving stops and you do not perform any
operations for 30 minutes or more, the unit automatically places itself in
standby mode.
Choices: On/Off
INPUT A
INPUT B
DVI
INPUT A
Choices: On/Off
Display Language
9
Automatically changes inputs when the unit does not receive a signal.
If the signal the unit is currently receiving stops, or the input signal you selected the last
time you used the unit does is not available when you turn the unit power on, it
automatically searches through inputs for a signal in the following order.
D4 VIDEO
S VIDEO
VIDEO
Selects the language used in the menu display.
Choices:
/English/Deutsch/Español/Français/Italiano/Portuguêsa/
Menu
Auto Input Search
HDMI
/
Displays the total lamp running time.
Opens the submenu to reset the running time. See page 45 for the operational procedure.
Reset
Resets menu settings to the factory presets.
Resets all the settings to the factory presets, and return the configurations stored in the
memory to the factory presets. See page 44, 53 and 54 for the operational procedure.
• [All Settings]
: Return all settings in the [Initial] and [Setup] menu groups in the
main menu, and all configurations stored by the memory function, to
the factory presets.
• [All Memory]
: Return all configurations stored by the memory function to their
default settings.
• [Current Memory] : Return the currently selected memory configuration (corresponding
to the signal input from the currently selected input jack) to their
default settings.
35
13_DPX-1300_E.p65
35
9/20/05, 5:08 PM
English
Lamp Running Time
Menu items
◆ Setup
Location
Designate the location of the main unit.
Choices: [Front/Table] [Front/Ceiling] [Rear/Table] [Rear/Ceiling] (☞ page 12)
V Keystone Correction
Adjusts the projection angle of the image.
If you do not install the projector at right angles to the screen, the image will be trapezoidally
distorted. You can electronically correct this distortion using this function to adjust the width
without changing the height of the image. Increase the keystone value (0 to +50 ) when the
upper part of the image is overly wide, and reduce it (-50 to 0 ) when the lower part is overly
wide.
When the upper part of
the image is wider than the lower part
When the lower part of
the image is wider than the upper part
Increase the value
in the positive (+) direction
H Keystone Correction
Decrease the value
in the negative (-) direction
Adjusts the projection angle of the image.
If you do not install the projector at right angles to the screen, the image will be trapezoidally
distorted. You can electronically correct this distortion using this function to adjust the height
without changing the width of the image. Increase the keystone value (0 to +50 ) when the right
side of the image is overly high, and reduce it (-50 to 0 ) when the left side is overly high.
When the right side of
the image is higher than the left side
When the left side of
the image is higher than the right side
Increase the value
in the positive (+) direction
Decrease the value
in the negative (-) direction
Remote Control Sensor
Sets the remote control sensor.
The main unit has two remote control sensors, one on the front panel and one on the rear,
which this setting allows you to switch between. The remote control functions regardless of
the setting of this parameter if you use a wired connection to connect it to the main unit.
Choices: Front & Rear/Front/Rear/Off
Remote Control ID
Sets the remote control ID.
Selects ID1 or ID2 for each main unit when operating two main units with one remote
control. You can select the controllable main unit with the remote control code switch on
the remote control.
Choices: ID1/ID2
Lens Adjustment Lock
Locks the lens adjustment function.
Locks the lens so that you cannot change the V.POS, ZOOM, and FOCUS settings
accidentally when set to [ON]. Set to [OFF] to cancel this function.
Lamp Power
Lowers the power supply to the lamp.
You can adjust the power supplied to the lamp within the range of 80 to 100%.
36
13_DPX-1300_E.p65
36
9/20/05, 5:08 PM
Menu items
Menu Color
Selects the color of the letters and background the main unit uses to display
the menu on screen.
You can choose to display the menu screen in [Monotone] or [Color]. Also, you can adjust
the contrast and brightness of the menu from the [Menu Brightness] and [Menu Contrast]
menus. You can select from 3 color types.
Monotone
Menu Brightness
Menu Contrast
Choices: Menu Brightness
Menu Contrast
Message
Color
Menu Brightness
Menu Contrast
Color Style
:-10 to 0 to +10
: 0.50 to 1.50
Selects whether to display memory number, input signal and other
information on the projection screen. (☞ page 62)
Choices: On/Off
Trigger Out
Sets the TRIGGER OUT terminal.
Set the external control TRIGGER OUT jack 12 V signal emission to [Lamp] to
synchronize it to the ON/OFF state of the lamp, to [Fan] to synchronize it to the fan, and to
[RS-232C] to receive ON/OFF signals through the RS-232C terminal.
Choices: Lamp/Fan/RS-232C
Baud Rate
Sets the transmission speed of the RS-232C terminal.
This setting becomes valid from the next time you switch the unit on.
Choices: 9600bps/19200bps/38400bps/57600bps/115200bps
9
Menu
English
37
13_DPX-1300_E.p65
37
9/20/05, 5:08 PM
Menu operations
◆ Operation button functions
Use the buttons on the remote control or the main unit to operate the menus. The button functions are listed below.
1 Menu Button
Remote Control
Opens/Closes the menu.
2 Cursor button
+ / - (Move the cursor ringht/left)
• Selects menu groups.
• Opens/Closes submenus.
• Selects/Changes settings.
h / g (Moves the cursor up/down)
• Selects menu items.
• Selects/Changes settings.
AUTO
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
MENU
ESCAPE
4
1
2
3
3
button
• Confirms setting changes.
• Opens the in-line menu when the menu is not open.
• Selects special operation (☞ page 42) and memory operation. (☞ page 48)
4 ESCAPE button
5
ASPECT
INPUT
RESET
HIDE
• Returns the cursor one level up the menu (e.g. From the menu item level to the menu
group level).
• Closes submenus.
• Closes the menu screen when the cursor is in a menu group.
• Returns from the menu movement bar to the menu entry screen, after moving a menu.
LIGHT
STILL
INPUT
S VIDEO
A
HDMI
VIDEO
B
DVI
5 RESET button (Remote control only)
Returns parameters back to their default settings (Does not affect items with no default
setting).
D4
MEMORY
1
2
3
4
5
6
Main Unit
4
STANDBY/ON
MENU
ESCAPE
PATTERN
1
SETTING
ASPECT
INPUT
LAMP
COVER
TEMP
2
3
FAN
38
14_DPX-1300_E.p65
38
9/20/05, 5:08 PM
Menu operations
◆ Menu operations 1 (with no submenu)
Menu operations use the procedure below to adjust menu item without submenus.
Select a menu group (Image / Signal / Initial / Setup)
(Select with the +/- buttons)
Menu items related to the selected menu group are displayed.
Select an item to adjust or a setting
(Select with the h / g buttons)
You can now adjust the selected item.
Choose a setting for the selected item
(Usually, use the +/- buttons)
MENU Button
AUTO
STANDBY/ON
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
ESCAPE
ESCAPE
COVER
TEMP
FAN
INPUT
Remote Control
Memo
SETTING
INPUT
LAMP
Signal
Initial
Black Level
0
White Level
0
•
a
Hue
MENU
ASPECT
Move Menu Window
Image
Gamma Trim
MENU
PATTERN
ASPECT
1. Press the MENU button to open
the menu screen.
Main Unit
b
c
d
e
0
Saturation
If you have opened the menu screen
previously, the menu displays the
settings from the last time you used it.
Setup
100
Sharpness Gain
2
Sharpness Type
2
Color Adjustment
WRGB
White Peaking
+0.000uv
6500K -
0
Iris
Level Adjustment
9
2. Press the + or - button to select a
menu group.
or
Move Menu Window
Image
Signal
Initial
Location
Remote Control
Main Unit
The illustration at right depicts the [Setup]
group being selected.
VIDEO
Menu
Memory 1
Front / Table
V Keystone Correction
0
H Keystone Correction
0
Remote Control Sensor
Front & Rear
Remote Control ID
ID 1
Off
Lens Adjustment Lock
Lamp Power
Setup
On
82
Menu Color
Monotone
Message
Off
Trigger Out
Lamp
Baud Rate
115200bps
Memory 1
On
VIDEO
English
39
14_DPX-1300_E.p65
39
9/23/05, 12:04 PM
Menu operations
3. Press the h or g button to move
the cursor to the item you wish to
adjust.
or
Remote Control
The illustration at right depicts [Lens
Adjustment Lock] being selected.
Main Unit
Move Menu Window
Image
Signal
Initial
Location
Setup
Front / Table
V Keystone Correction
0
H Keystone Correction
0
Remote Control Sensor
Front & Rear
Remote Control ID
ID 1
Off
Lens Adjustment Lock
Lamp Power
On
82
Menu Color
Monotone
Message
Off
Trigger Out
Lamp
Baud Rate
115200bps
On
Memory 1
4. Press the + or - button to select a
suitable setting.
or
Move Menu Window
Image
Signal
Initial
Location
Remote Control
The illustration at right depicts the [Lens
Adjustment Lock] mode set to [On].
Main Unit
V Keystone Correction
0
H Keystone Correction
0
Remote Control Sensor
Front & Rear
Remote Control ID
ID 1
•
Lamp Power
The setting method depends on the
item selected.
Off
Monotone
Message
Off
Trigger Out
Lamp
Baud Rate
115200bps
Memory 1
or
Memo
•
Remote Control
Main Unit
ESCAPE Button
AUTO
STANDBY/ON
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
ESCAPE
MENU
ASPECT
INPUT
MENU
ESCAPE
PATTERN
SETTING
LAMP
COVER
TEMP
FAN
INPUT
ASPECT
Remote Control
Main Unit
MENU Button
AUTO
ZOOM
FOCUS
IRIS
SETTING
PATT
ESCAPE
MENU
ASPECT
INPUT
MENU
PATTERN
SETTING
LAMP
ASPECT
6. To close the menu screen when
you have finished making
adjustments, press the MENU
button.
STANDBY/ON
V. POS
ESCAPE
Press the h or g button to move the
cursor to another item in the same
group.
To move to an item in another menu
group, press the ESCAPE or h button
to return to the top of the menu group,
and repeat steps 2,3 and 4.
COVER
TEMP
FAN
INPUT
Remote Control
Main Unit
40
14_DPX-1300_E.p65
40
9/20/05, 5:08 PM
On
82
Menu Color
5. Move to another item or group as
necessary.
Setup
Front / Table
Lens Adjustment Lock
Memo
VIDEO
On
VIDEO
Menu operations
◆ Menu operations 2 (with submenus)
Use the procedure below to adjust menu items that contain submenus.
1. Carry out steps 1 to 3 from “Menu
Operations 1” to select the menu
item you want to set.
The illustration at right depicts [Display
Language] in the [Initial] group selected.
Memo
•
“ ” appears to the right of items that
contain a submenu.
Move Menu Window
Image
Signal
Initial
Color System
Auto
INPUT A Signal
Component
INPUT A Sync Type
Auto
INPUT B Signal
RGB TV
INPUT B Sync Type
Auto
HDMI Signal
Component
DVI Signal
Component
Setup
Auto Power Off
Off
On
Auto Input Search
Off
On
Display Language
English
Lamp Running Time
0 Hour
Reset
Memory 1
2. Press the + button to move to the
submenu.
VIDEO
Move Menu Window
Image
Signal
Initial
Setup
or
Memo
Remote Control
Main Unit
•
Some menu items contain other items
that you can select. In such cases,
move to the lower level submenu
using the + button.
English
Deutsch
Español
Français
Display Language
Italiano
Portuguêsa
Memory 1
Items using the
button for setting.
Display Aspect Ratio
VIDEO
3. Press the h or g button to adjust
item settings.
Color System
9
•
Input A Sync Type
Input B Signal
Input B Sync Type
When “
: Fix” appears in the
operations guide at the bottom left of
the menu screen, press the
button
to confirm the selected settings.
Menu
Memo
Input A Signal
English
Deutsch
Español
Français
Italiano
HDMI Signal
Portuguêsa
DVI Signal
Remote Control Sensor
VIDEO
Remote Control ID
4. Press the – or ESCAPE button to
return to higher level menu items.
5. To close the menu screen when
you have finished making
adjustments, press the MENU
button.
English
41
14_DPX-1300_E.p65
41
9/21/05, 3:44 PM
Menu operations
◆ Special operations
Some items in the menu require special methods to configure.
<Color Adjustment>
Example: Adjusting R (Red)
1. Select [Color Adjustment] in the [Image] group from the main menu.
2. Press the + button to enter submenus.
3. Select a suitable item from [Standard] • [WRGB] • [WRGBYCM] using the h or g button, and
press the + button.
This explanation uses the [WRGBYCM] menu as an example.
4. Press the h, g, +, or - button to select the item you wish to configure from the color scale, and
button.
press the
The Color coodinate adjustment area on the right side of the menu screen will be highlighted.
5. Press the h, g, +, or - button to adjust the setting for the item.
6. If you select R (red), G (green), B (blue), Y (yellow), C (cyan), or M (magenta) in step 4, press the
button to move to the gain adjustment area, and press the + or - button to adjust the gain.
7. Press the ESCAPE button to return to the color scale.
nu Window
Move Men
Image
The name of the
selected item appears
here.
Initial
Signal
Setup
x=0.640
Red
Color coordinate
display area
y=0.330
y
Press the
button.
y
0.35
0.5
Color coordinate
adjustment area
Use the h, g, +, or button to select an
item.
0.3
0.0
0.0
0.5
x
Press the ESCAPE
button.
: Edit
0.6
Gain
x
Memory 1
Gain setting
display area
0.65
0.82
Press the
button to
change the item to adjust.
VIDEO
Gain adjustment
area
Memo
• See page 32 for datails about each color item.
42
14_DPX-1300_E.p65
42
9/20/05, 5:08 PM
Menu operations
Example: Using the color temperature fixed mode
Use this mode when you want to adjust the RGB coordinate while keeping the color temperature setting unchanged.
1. Select [Color Adjustment] in the [Image] group from the main menu.
2. Press the + button to enter submenus.
3. Select [WRGB] from the [Standard], [WRGB], [WRGBYCM] using the h or g button, and press
the + button.
4. Press the h, g, +, or - button to select W (Color temperature and h UV) from the color scale,
button.
and press the
The color temperature adjustment area on the right side of the menu screen will be highlighted in white.
5. Press the h, g, +, or - button to adjust the color temerature.
6. Press the
The “
button to enter the color temperature fixed mode.
” icon appears on the W (Color temperature and h UV ) box.
Memo
•
In this mode, you cannot use the h, g, +, or - button to change the color temperature. If you try to change,
“The color temperature is fixed.” appears at the bottom of the menu screen.
7. Press the ESCAPE button to return to the color scale. Follow steps 4 to 5 in the “Example:
Adjusting R (Red)” on page 42 to adjust the color coordinates.
9
Memo
When using the color temperature fixed mode, the gain adjustment area will not be displayed.
•
To cancel the color temperature fixed mode, select the W (Color temperature and h UV) box and press the
button until the “
” icon disappeares.
Example:
Normal mode
Example:
Color temperature fixed mode
Move Men
Image
The name of the
selected item appears
here.
Move Men
Signal
Image
Color Temp.
y
Press the
button.
0.5
0.0
Signal
Color Temp.
y
When this unit is in
the color temperature
fixed mode, the “
”
icon appears on this
W (Color temperature
and h UV) box.
0.5
0.0
0.5
x
Press the
button.
0.0
When this unit is in the
normal mode, the “
”
icon dissapears.
0.0
0.5
x
English
ESCAPE : Return
ESCAPE : Return
43
14_DPX-1300_E.p65
43
Menu
•
9/21/05, 3:45 PM
Menu operations
<Resetting the selected settings>
Reset the selected settings to the default settings.
1. Select the item you wish to reset to the default setting
from the main menu.
2. Press the RESET button on the remote control to reset
to the default setting (resetting does not affect items
with no default setting).
Memo
•
The RESET button has a special function when selecting
[WRGBYCM] in [Color Adjustment]. (☞ page 32)
•
The RESET button resets the parameters to their default
settings (corresponding to the signal input: HDTV or SDTV)
when the Color coordinate adjustment area is selected after
selecting [WRGB] or [WRGBYCM] in [Color Adjustment]. (☞
page 32)
<Resetting all the settings>
Reset all of your settings to its factory presets.
1. From the menu screen, select [Initial]
[All Settings].
[Reset]
Move Menu Window
Image
Signal
Initial
Setup
All Settings
Reset
All Memory
Current Memory
2. Press the + button to display a confirmation message.
Memory 4
+ : Enter
3. Press the
button to reset to the default settings.
VIDEO
Move Menu Window
Image
Signal
Initial
Setup
Memo
•
To cancel this operation and return to the previous screen,
press the ESCAPE button.
Press "
" to reset
to factory settings.
<Changing the position of the menu screen.>
Memory 4
ESC : Return
VIDEO
Change the position of the menu on the screen.
Move Menu Window
1. In the menu screen, press the ESCAPE or h button
and move the cursor to one of the menu groups.
Image
Signal
Initial
Setup
2. Press the h button to enter [Move Menu Window].
3. Use the h, g, +, or - button to move the menu screen
to a location of your choice.
4. Press the ESCAPE button to return to the previous
menu screen.
ESC : Return
44
14_DPX-1300_E.p65
44
9/20/05, 5:08 PM
Memory 1
VIDEO
Menu operations
<Resetting the lamp running time>
Reset the [Lamp Running Time] displayed on screen to “0”.
1. From the menu screen, select [Initial]
Running Time].
[Lamp
Move Menu Window
Image
Signal
Initial
Color System
Auto
INPUT A Signal
Component
INPUT A Sync Type
Auto
INPUT B Signal
RGB TV
INPUT B Sync Type
Auto
HDMI Signal
Component
DVI
Component
Setup
Auto Power Off
Off
On
Auto Input Search
Off
On
Display Language
English
Lamp Running Time
12 Hours
Reset
Memory 1
+ : Enter
2. Press the + button to open the confirmation screen.
VIDEO
Move Menu Window
Image
Signal
Initial
Setup
3. Press the h or g button to select [Yes].
4. Press the
button to confirm.
Press "
" to reset lamp running time.
No
Memo
•
Yes
To cancel the operation and return to the menu screen, select
[No].
Lamp Running Time
12 Hours
Memory 4
: Fix
VIDEO
9
Use the [Subtitle Area] menu to adjust the size of the subtitle display area. Use [V Scroll] to adjust the vertical position of the subtitle display.
1. From the menu screen, select [Signal]
[Special].
Aspect Ratio]
[Display
Menu
<Subtitle Zoom>
Move Menu Window
Image
Special
Signal
Initial
Setup
Subtitle Zoom
Cinema Zoom
2. Press the + button to enter the lower level selection
menu.
Cinema Squeeze
14:9 Zoom
3. Select [Subtitle Zoom] with h or g buttons.
4. Press the
button.
“ ” appears to the right of [Subtitle zoom].
Memo
•
+ : Enter
Memory 1
VIDEO
After the first time you carry out this procedure, “ ” appears
beside [Subtitle Zoom] automatically.
English
45
14_DPX-1300_E.p65
45
9/20/05, 5:08 PM
Menu operations
5. Press the + button to enter the lower level selection
menu.
Move Menu Window
Image
Signal
Initial
Setup
Subtitle Zoom
6. Press h or g button to select [Subtitle Area] or [V
Scroll].
Subtitle Area
0
V Scroll
0
7. Press the + or – button to select a suitable setting.
Memo
•
Press the h or g button to move to a different menu item in
the [Subtitle Zoom] menu.
VIDEO
Memory 1
ESC : Return
8. Press the ESCAPE button to return to the higher level
selection menu.
<Changing the [Gamma] page>
Select a gamma control pattern (color tone characteristics) from the 10 preset patterns. (☞ page 30)
1. From the menu screen, select [Image]
[Gamma].
Move Menu Window
Image
button to switch between capital (A to E)
2. Press the
and non capital (a to e) letters.
Signal
Black Level
0
White Level
0
Aa
Gamma
3. Use the + or – button to select an appropriate setting.
Initial
Hue
A
Setup
B
C
D
E
0
Saturation
100
Sharpness Gain
2
Sharpness Type
2
Color Adjustment
+0.000uv
6500K -
WRGB
White Peaking
0
Iris
Level Adjustment
Memory 1
: Exchange
Press the
VIDEO
button
Move Menu Window
Image
Black Level
White Level
Gamma
Hue
Saturation
Signal
Initial
0
Aa
a
b
c
d
e
0
100
Sharpness Gain
2
Sharpness Type
2
Color Adjustment
White Peaking
Setup
0
WRGB
+0.000uv
6500K -
0
Iris
Level Adjustment
: Exchange
46
14_DPX-1300_E.p65
46
9/20/05, 5:08 PM
Memory 1
VIDEO
Menu operations
◆ Adjusting image quality using the inline menu
Use the inline menu to adjust image quality without obstructing the image during projection. See “Menu group items and functions” (page 30
- 37) for information on each setting.
<Inline menu composition>
Indicates that you can use the h and g buttons to
change the position of the inline menu.
Black Level
Inline menu item
Parameter adjustment area
<Inline menu item list>
The menu items available may differ depending on the input signal type.
For video type sources
Black Level
White Level
Gamma
Hue
Saturation
Color Temp.
White Correction
For PC type sources
Sharpness Gain
Sharpness Type
White Peaking
Iris
Brightness
Contrast
Gamma
Color Temp.
White Correction
White Peaking
Iris
Memo
•
When [Sharpness Type] is set to [0], the [Sharpness Gain] adjustment cannot be performed.
<Example: Using the inline menu>
button when the menu is not open.
Menu
1. Press the
9
Image menu items appear one at a time in the lower area of the screen. If you do not carry out any operations within 5 seconds, the menu
disappears.
Black Level
Press the h or g button to select an item to set.
Gamma
Aa
A
B
C
D
E
Press the + or - button to set the item to an appropriate setting.
Press the RESET button to return the item to its default setting.
Gamma
Aa
A
B
C
D
E
2. To close the menu when you have finished making adjustments, press the ESCAPE button.
Memo
Press the
button to change between the pages of the [Gamma] menu.
English
•
47
15_DPX-1300-E.p65
47
9/20/05, 5:08 PM
10 Memory function
(Save, Recall, Lock, Copy, Reset)
The memory function automatically saves the settings of menu items listed in the “Items to be saved” table below.
◆ Memory configurations
The DPX-1300 stores up to six sets of configurations, called memory numbers, for each input jack. For each memory number, the DPX1300 stores specific configurations for each signal type, giving a total of 90 configurations.
Memory configurations for each input jack
Input
Input Signal Type
VIDEO
–
6
S VIDEO
–
6
INPUT A
SDTV
HDTV
RGB-PC
6
6
6
INPUT B
SDTV
HDTV
RGB-PC
6
6
6
HDMI
SDTV
HDTV
6
6
DVI
SDTV
HDTV
RGB-PC
6
6
6
D4
The Number of Memories
SDTV
HDTV
Total
Items to be saved
Image
Signal
Black Level (Brightness)
White Level (Contrast)
Gamma
Hue
Saturation
Color Temp.
White Correction
Sharpness Gain
Sharpness Type
Color Adjustment
White Peaking
Iris
Level Adjustment
3D Y/C Separation
Progressive Mode
Color Space Conversion
Setup Level
Overshoot Supp. Range
Overshoot Supp. Level
Noise Reduction Type
Noise Reduction Level
Horiz. Display Position
Vert. Display Position
Signal Level
6
6
90
◆ Saving memory settings
All memory numbers have default settings. Since the DPX-1300 saves any changes in the menu item to the current memory number, you do
not need to save the settings each time. To preserve the specific settings, use the “Memory lock” function (☞ See page 50).
◆ Recalling a memory number
<Using the remote control>
1. Press the MEMORY button (in the
MEMORY area) of which you want
to recall the settings.
LIGHT
STILL
INPUT
S VIDEO
VIDEO
A
HDMI
B
DVI
D4
MEMORY
MEMORY area
1
2
3
4
5
6
Remote Control
<Using the menu>
MENU Button
AUTO
STANDBY/ON
V. POS
ZOOM
FOCUS
IRIS
SETTING
PATT
ESCAPE
ESCAPE
MENU
ASPECT
INPUT
MENU
PATTERN
SETTING
LAMP
ASPECT
1. Select the [Image] or [Signal]
group from the menu screen.
COVER
TEMP
FAN
INPUT
Remote Control
Main Unit
48
15_DPX-1300-E.p65
48
9/20/05, 5:08 PM
2. Press the g button to select
“Memory number status” from
the bottom of the screen.
Move Menu Window
Image
or
Signal
Initial
Black Level
0
White Level
0
a
Gamma Trim
c
d
e
100
Saturation
Main Unit
b
0
Hue
Remote Control
Setup
Sharpness Gain
2
Sharpness Type
2
WRGB
Color Adjustment
White Peaking
+0.000uv
6500K -
0
Iris
Level Adjustment
+ : Enter
Memory 1
VIDEO
Memory number status
3. Press the + button to open the
submenu.
Move Menu Window
Image
Signal
Initial
Setup
or
Remote Control
Main Unit
Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
: Fix
Memory 6
VIDEO
4. Press the h or g button to select
a memory number.
or
Remote Control
Main Unit
10
Memo
or
•
Remote Control
Main Unit
When the unit receives a signal with a different resolution from the same input jack,
it detects the new resolution and recalls an appropriate memory settings.
Memory function
button to recall the
5. Press the
settings in the selected memory.
English
49
15_DPX-1300-E.p65
49
9/20/05, 5:08 PM
◆ Memory lock
The lock function protects information in a memory not to be overwritten. You can set the lock function for each memory number, and
additionally for each SDTV/HDTV/RGB-PC input.
<Setting Memory Lock>
Move Menu Window
1. Recall the memory number you
wish to lock.
2. Select a memory number status.
or
Image
Signal
Black Level
0
White Level
0
a
Gamma Trim
Remote Control
button.
2
Sharpness Type
2
c
d
e
+0.000uv
6500K -
WRGB
White Peaking
“ ” appears beside locked memory
numbers.
b
100
Sharpness Gain
Color Adjustment
Main Unit
Setup
0
Hue
Saturation
3. Press the
Initial
0
Iris
Level Adjustment
Memory 1
“
VIDEO
”appears
<Deactivating Memory Lock>
1. Select the memory number you
wish to unlock.
2. Select a memory number status.
or
Move Menu Window
Image
Remote Control
button.
Main Unit
Initial
Black Level
0
White Level
0
a
Gamma Trim
Hue
3. Press the
Signal
Saturation
c
d
e
100
Sharpness Gain
2
Sharpness Type
2
White Peaking
b
0
WRGB
Color Adjustment
“ ” disappears from the memory status
screen and the memory lock is removed
from the memory number you selected.
Setup
+0.000uv
6500K -
0
Iris
Level Adjustment
+ : Enter
Memory 1
“
VIDEO
”disappears
Memo
•
You can change settings when the memory is locked, but the unit does not save the changes to a memory. Any changes you make
are erased when you place this unit to standby mode. (The memory number status color changes from white to gray if you change
any menu items while the memory is locked.)
50
15_DPX-1300-E.p65
50
9/22/05, 7:52 PM
◆ Memory copy
Copy the settings stored in a memory number to another memory number.
1. Recall the memory number to be
the copy source.
2. Press the g button to select
“Memory number status” from
the bottom of the screen.
or
Move Menu Window
Image
Signal
Initial
Black Level
0
White Level
0
Gamma Trim
a
Hue
Remote Control
b
c
d
e
0
Saturation
Main Unit
Setup
100
Sharpness Gain
2
Sharpness Type
2
Color Adjustment
WRGB
White Peaking
+0.000uv
6500K -
0
Iris
Level Adjustment
+ : Enter
Memory 1
VIDEO
Memory number status
3. Press the + button to open the
submenu.
Move Menu Window
Image
Signal
Initial
Setup
or
Remote Control
Main Unit
Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
Memory 6
: Fix
or
Main Unit
Remote Control
10
Move Menu Window
Image
Signal
Initial
Setup
Memory function
4. Press the h or g button to select
a memory number to be the copy
destination.
VIDEO
Memo
•
•
You cannot select a source memory
number (gray colored) as a copy
destination.
You cannot select a locked memory
number (marked “ ”) as a copy
destination.
Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
: Fix
: Copy
Memory 6
VIDEO
English
51
15_DPX-1300-E.p65
51
9/20/05, 5:08 PM
5. Press the + button to display the
confirmation screen.
Move Menu Window
Image
Signal
Initial
Setup
or
Copy the Memory?
Press
to confirm.
Main Unit
Remote Control
Yes
No
Memory 1
Memory 2
Memory 3
6. Press the h or g button to select
[Yes] .
or
Memory 4
Memory 5
VIDEO
Main Unit
Remote Control
7. Press the
button.
Move Menu Window
Image
or
Main Unit
Remote Control
The settings stored in the source memory
number are copied to the destination
memory number.
If the copy is complete, the memory status
screen dislplays the memory number
selected in step 1.
52
52
Signal
Initial
Setup
Copying to Memory 3 ...
: Fix
15_DPX-1300-E.p65
Memory 6
: Fix
9/20/05, 5:08 PM
Memory 1
VIDEO
◆ Resetting to the default settings in the memory menu
Reset the settings stored in the memories to the default settings.
<Initialization of the currently selected memory>
Follow the procedure below to revert settings stored in the selected memory (corresponding to the signal input from the currently selected
input jack) to their default settings.
Move Menu Window
1. From the main menu, select
Image
Signal
Initial
Setup
[Reset]
[Current
[Initial]
Memory].
All Settings
Reset
All Memory
Current Memory
Memory 4
+ : Enter
2. Press the + button to display the
confirmation screen.
VIDEO
Move Menu Window
Image
Signal
Initial
Setup
or
Remote Control
Main Unit
Press "
ESC : Return
" to reset current memory.
Memory 4
VIDEO
button to reset the
3. Press the
settings to their default settings.
10
or
Memory function
Remote Control
Main Unit
English
53
15_DPX-1300-E.p65
53
9/20/05, 5:08 PM
<Initialization of all the memories>
Reset all the settings in the memories to their default settings regardless of the input jack or input signal.
1. From the main menu, select
[Reset]
[All
[Initial]
memory].
Move Menu Window
Image
Signal
Initial
Setup
All Settings
Reset
All Memory
Current Memory
Memory 4
+ : Enter
2. Press the + button to display the
confirmation screen.
VIDEO
Move Menu Window
Image
Signal
Initial
Setup
or
Remote Control
Main Unit
Press "
" to reset
all Memory.
ESC : Return
3. Press the
button to reset the
settings to their default settings.
or
Remote Control
Main Unit
54
15_DPX-1300-E.p65
54
9/20/05, 5:08 PM
Memory 4
VIDEO
11 Reference
Glossary
The following is a list of key words used in the use of projectors and image signals and their explanations. Please refer to it when using this
manual. For an explanation of vocabulary used in the menu, refer to "Menu group items and functions” ( ☞ page 30 - 37).
Ceiling mount bracket
HDTV
The mounting hardware used to hang this unit from the ceiling.
Two types of bracket are available, for high and low ceilings.
Ceiling mount brackets are sold separately.
High-Definition Television, a term used to define systems that
satisfy the following conditions:
• A vertical resolution of 720p or 1080i (p stands for progressive
scans, i stands for interlace scans)
• A 16:9 aspect ratio
Cinemascope size
The widest film format in 70 mm film, with an aspect of 2.35:1.
Interlace
Color spacing
The conversion of YUV color separated signal to RGB signal.
There are two formats for this, BT.601 for SDTV, and BT.709 for
HDTV. This unit switches between them as required.
Component video signal
A method of sending video signals with independent luminance
and color signals. Component video gives a higher image quality
than ordinary composite video because it bypasses mixing and
separating circuits. Component video signal consists of three lines,
the luminance signal (Y), and two color difference signals (PB/CB,
PR/CR).
Composite video signal
The most common type of video signal, combining luminance and
color signals in one line. This method requires mixing and
separating processes on both the send and receive sides. Use a pin
cable for connection.
DLPTM technology
Digital Light Processing, an image display engine used in
projectors that use the DMD™ chip developed by Texas
Instruments.
DVI terminal
A digital RGB/Component signal is sent differently from a
computer or A/V equipment to this terminal. A 24-pin connector
and cable are used.
The most common type of scanning used in televisions. It divides a
screen into even and odd numbered fields for scanning, and then
builds an image by combining them into one image (frame).
Keystone Correction
Using the unit at an angle to the screen distorts the projected image
trapezoidally. You can use V Keystone Correction or H Keystone
Correction to electronically correct this distortion.
Letterbox
A method of converting the content of landscape oriented film to a
4:3 signal. You can watch landscape images without trimming them
by adding a black bar to the top and bottom of the screen, however
this sacrifices vertical resolution to some extent.
Progressive
A method of displaying all scanning lines in a frame at once,
reducing flicker noticeable on a larger screen and creating a sharp,
smooth image. This unit uses progressive scanning for progression.
RGB Signal
A method of transmitting color information using a numeric
representation of the primary colors red, green, and blue separately.
When received, it is expressed in various colors by adding a mixing
colors. RGB is widely used for sending and receiving color images
between computers, and requires horizontal and vertical sync
signals.
SDTV
D terminal
A cable that allows transmission of all of the signals in composite
video in one cable. This method is used for transmitting image
signals between the latest AV components. There are 5 methods of
transmission, D1-D5. This unit is compatible with D4.
Standard-Definition Television, a term used to define systems that
satisfy the following conditions:
• A resolution of 480i or 576i (i stands for interlace scans)
• A 4:3 or 16:9 aspect ratio
Smart zoom
EDTV
HDCP
A technique designed to protect the video transmission between a
DVI or HDMI transmitter and a display device.
HDMITM
High-Definition Multimedia Interface, a method of differentially
transmitting digital RGB/component video signal from computers
and home digital equipment.
Expands the left and right sides of a 4:3 image without altering the
center, when you are attempting to project a 4:3 image on a wide
screen format. This creates some distortion at both edges.
Squeeze
A method of compressing film images horizontally to an aspect of
ratio of 4:3 when recording to video medium. The raw image is
oblong, so needs to be passed through a desqueezing circuit to be
projected in it’s original form.
11
Reference
Extended-Definition Television, a term used to define systems that
satisfy the following conditions:
• A resolution of 480p or 576p (p stands for progressive scans)
• A 4:3 or 16:9 aspect ratio
Standby
The state in which the circuit that receives infrared-signals from the
remote control is active, but all other main circuits are turned on.
The unit consumes a small amount of power in this state.
S Video signal
55
16_DPX-1300_E.p65
55
9/21/05, 3:47 PM
English
S stands for Separate. A method of sending signals with separate
luminance (Y) and color (C) signals. Use a 4-pin mini DIN
connector and cable for connection.
Glossary
Sync.
* DLPTM, DMDTM, DarkChip2TM, and DarkChip3TM are registered
trademarks of the Texas Instruments corporation of America.
Computers output signals with a given regular frequency, which
you must synchronize the projector to in order to produce a good
quality image. If you do not match the phase of the signal, the
image may be flickery, faded, or distorted.
Test pattern
* HQVTM, Hollywood Quality VideoTM and HQV powered by
TeranexTM are trademarks of Silicon Optix inc.
This unit contains test patterns which you can use to adjust the
position and focus of the projected image on the screen.
Tracking
Computers output signals with a given regular frequency, which
you must synchronize the projector to in order to produce a good
quality image. If you do not match the phase of the signal, vertical
stripes may appear on the image.
* HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademark of HDMI
Licensing LLC.
Vista size
A standard film size, with an aspect ratio of 1.85:1 in North
America, and 1.66:1 in Europe.
3-2 pulldown detection style IP conversion
* The “HD ready” Logo is a trademark of EICTA.
A function for directly converting interlace signal into sixty frame
progressive signal used when receiving 60 field interlace signal
from an image source recorded with the same 24 frames as movie
film. This allows DVD and other materiel recorded with 24 frames
to be projected on large screens as a natural, precise image with no
loss of quality, comparable to a movie film.
Compatible signal types
The following tables show the types and formats of signals the DPX-1300 can project. Signals other than those listed here may not be
projected correctly.
◆ TV format 1 (Composite or S Video signals received at the VIDEO or S-VIDEO jack)
V active
(lines)
Signal type
NTSC
PAL
SECAM
PAL60
NTSC4.43
PAL-M
PAL-N
480
576
576
480
480
480
576
f (V)
(Hz)
59.94
50.00
50.00
59.94
59.94
59.94
50.00
fsc
(MHz)
3.580
4.430
4.406, 4.250
4.430
4.430
3.580
3.580
Color system
NTSC
PAL
SECAM
PAL
NTSC
PAL
PAL
◆TV Format 2 (Component/RGB TV signals received at the INPUT A and B, or component signals received at the D4 jack)
H active
(pixels)
Signal type
480i
576i
480p
576p
720p/50Hz
720p/60Hz
1080i/50Hz
1080i/60Hz
720
720
720
720
1280
1280
1920
1920
V active
(lines)
480
576
480
576
720
720
1080
1080
f (H)
(kHz)
15.734
15.625
31.469
31.250
37.500
44.955
28.125
33.716
56
16_DPX-1300_E.p65
56
9/20/05, 5:08 PM
f (V)
(Hz)
59.940
50.000
59.940
50.000
50.000
59.940
50.000
59.940
Compatible signal types
◆PC Format
(Analog RGB PC signals received at the INPUT A or B jack)
H active
(pixels)
Signal type
VESA (*1)
VGA/60Hz
VGA/72Hz
VGA/75Hz
VGA/85Hz
SVGA/56Hz
SVGA/60Hz
SVGA/72Hz
SVGA/75Hz
SVGA/85Hz
XGA/60Hz
XGA/70Hz
XGA/75Hz
XGA/85Hz
SXGA/60Hz
Macintosh (*2)
V active
(lines)
640
640
640
640
800
800
800
800
800
1024
1024
1024
1024
1280
640
f (H)
(kHz)
480
480
480
480
600
600
600
600
600
768
768
768
768
1024
480
f (V)
(Hz)
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.677
63.981
35.000
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
60.020
66.666
(*1) VESA is a registered trademark of the Video Electronics Standards Association.
(*2) Macintosh is a registered trademark of the Apple Computer corporation.
◆DVI Format
(RGB signals input from the DVI jack)
H active
(pixels)
Signal type
VGA/60Hz
SVGA/60Hz
XGA/60Hz
SXGA/60Hz
480p
576p
720/60p
720/50p
1080/60i
1080/50i
640
800
1024
1280
720
720
1280
1280
1920
1920
◆HDMI Format
V active
(lines)
480
600
768
1024
480
576
720
720
1080
1080
VGA
480i
576i
f (V)
(Hz)
59.940
60.317
60.004
60.020
59.940
50.000
59.940
50.000
59.940
50.000
Component type
RGB
RGB
RGB
RGB
RGB
RGB
RGB
RGB
RGB
RGB
(Component/RGB signals input from the HDMI jack)
H active
(pixels)
Signal type
f (H)
(kHz)
31.469
37.879
48.363
63.981
31.469
31.250
44.955
37.500
33.716
28.125
V active
(lines)
f (V)
(Hz)
59.940
59.940
50.000
Component type
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
480
31.469
59.940
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
480p
640
(1440) 720
(1440) 720
720
1440
576p
720
1440
576
31.250
50.000
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
720/60p
720/50p
1080/60i
1080/50i
1280
1280
1920
1920
720
720
1080
1080
37.500
44.955
33.716
28.125
59.940
50.000
59.940
50.000
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
RGB/YCBCR4:4:4/YCBCR4:2:2 (*3)
11
Reference
480
480
576
f (H)
(kHz)
31.469
15.734
15.625
(*3) You cannot select YCBCR4:2:2 mode manually. This mode only available when you set the unit to HDMI Auto mode.
English
57
16_DPX-1300_E.p65
57
9/20/05, 5:08 PM
Maintenance
Maintenance
◆ Regular care
Be sure to disconnect the power cable before doing any maintenance.
<Main unit>
Wipe with a soft cloth. Use a damp cloth with a mild detergent and then wipe with a dry cloth again if the unit is heavily soiled. Do not use
strong solvents such as thinner or alcohol as they may damage the unit casing.
<Lens>
Use commercially available blowers or lens tissue to remove any dirt from the lens.
<Filter>
If dust accumulates on the ventilation port filter, the internal temperature of the unit rises, which may cause damage to the unit. Clean the
filter approximately once every 200 hours. Remove the power cable from the AC outlet, and remove dust from the filter with a vacuum
cleaner.
To prevent dust from entering the filter itself, be sure to vacuum the filter with the unit on its side.
◆ Replacing the filter
Replace the filter when it becomes difficult to remove dust from it.
1. Turn off the power and remove the power cable.
2. Carefully place the unit upside down on a soft cloth to prevent scratching.
3. Press the filter hook on the underside of the main unit to remove the filter.
4. Firmly attach the new filter. The lamp does not light if the filter is
incorrectly attached.
Warning
•
Contact a YAMAHA dealer or service center if you require replacement filters.
58
16_DPX-1300_E.p65
58
9/20/05, 5:08 PM
Maintenance
◆ Replacing the lamp
The lamp used as a light source in the DPX-1300 is a consumable item which will gradually lose its brightness during the course of use. It is
advisable to replace the lamp when running time has exceeded 2000 hours.
You can check the lamp running time in the [Lamp Running Time] in the [Initial] menu group of the Menu screen. The LAMP warning
indicator will blink when running time exceeds 2000 hours.
There will also be a message displayed on the screen. In this case, follow the instructions below to replace the lamp cartridge. For details on
replacement of lamp cartridges, consult the store where you purchased the DPX-1300.
Warning
•
Be sure to use the replacement lamp cartridge PJL-427. Other lamp cartridges are not suitable for use in the DPX-1300.
•
If replacing the lamp of the projector that has been installed to the ceiling, you should remove the projector from the ceiling before
replacing the lamp.
•
Before starting to replace the lamp cartridge, turn off the power, disconnect the power cable after the fan has completely stopped,
and wait at least one hour for the lamp to cool down.
•
Do not remove any other screws than those specified in the following steps.
•
The gases inside the lamp contain mercury vapor. Be careful the lamp may break if it gets old or overtasked. The life of a lamp
differs depending on operation environments.
1. Loosen the lamp cover screws.
Lamp cover screws
2. Remove the lamp cover.
3. Loosen the screws of the lamp cartridge.
11
Reference
4. Grip the handle and pull the lamp cartridge to remove it.
5. Insert the new lamp cartridge by reversing the above steps, and tighten
the screws to fix it into place.
7. Connect the unit to the power outlet, turn the unit on, and reset [Lamp
Running Time] on the [Initial] group in the menu. (☞ page 45)
59
16_DPX-1300_E.p65
59
9/20/05, 5:08 PM
English
6. Replace the lamp cover and secure it with the screws.
The lamp will not turn on if the cover is not securely fastened. Take care
to attach it firmly in place.
Troubleshooting
Troubleshooting
Problem
Cause
The DPX-1300 does not The power cable is not plugged in.
turn on.
You attempted to turn on The DPX-1300
immediately after turning it off.
Remedy
Plug the power cable in firmly.
Wait for approximately two minutes.
<MEMO>
• To protect the lamp, you cannot turn on
power for two minutes after you turn it off.
No picture.
The filter cover is not correctly attached.
Correctly attach the filter cover.
The lamp cover is not correctly attached.
Correctly attach the lamp cover.
The lens cover has not been removed.
Remove the lens cover.
The DPX-1300 is not correctly connected
to the other components.
Check the connections.
The input signal has not been correctly
selected.
Select the correct input signal with the
INPUT button.
Press the AUTO button on the remote
control.
Use the menu to adjust the signal setting
to suit the input setting.
[Initial]
The picture is turned off.
Press the HIDE button again to cancel the
HIDE function.
The computer is not set to display on the
external monitor.
Set the computer to display on the external
monitor. (Refer to the computer operating
instructions.)
When a component is
HDCP (High-bandwidth Digital Content
digitally connected to
Protection) testing failed.
the HDMI or DVI
terminal, white noise or
a black image appears.
Press the Auto button on the remote
control or unplug the digital connection
cable, and then insert the cable again.
Image is unstable.
The connection cables are not correctly
attached to the connectors.
Correctly connect the cables to the
appropriate connectors.
Picture is blurred.
The lens is not correctly focused.
Press the FOCUS button, and adjust the
focus.
The screen and the DPX-1300 are not
facing each other directly.
Adjust the projection angle and direction,
and the height of the DPX-1300.
The image becomes
cloudy.
There is condensation on the DPX-1300.
Switch the DPX-1300 power off until the
condensation disappears.
Cannot adjust focus or
zoom, or the vertical
position of the lens.
[Lens Adjustment Lock] in the menu is set
to ON.
Set correctly.
Set [Lens Adjustment Lock] to off.
Press the MENU button to display the menu
and select [Setup]
[Lens Adjustment
Lock].
60
16_DPX-1300_E.p65
60
9/20/05, 5:09 PM
Troubleshooting
Problem
Cause
Remote control does
not work correctly.
•
Remedy
The batteries are exhausted.
Replace both batteries with new ones.
The remote control sensor is not set
correctly.
Set correctly.
Press the MENU button to display the menu
and select [Setup]
[Remote Control
Sensor].
There is a fluorescent lamp near the
remote control sensor being used.
Turn off the remote control sensor near the
fluorecent lamp, and use the other remote
sensor.
The remote control code switch is
incorrectly set.
Set the remote control code switch to the
same ID number as the setting on the
“REMOTE CONTROL ID” in the setting menu.
COVER warning
indicator lights up.
The filter cover is not correctly attached.
Tightly attach the filter cover.
The lamp cover is not correctly attached.
Tightly attach the lamp cover.
LAMP warning
indicator lights up or
blinks.
Lamp running time has exceeded 2000
hours.
Replace the lamp with a new one.
The lamp has burned out.
Replace the lamp with a new one.
TEMP warning indicator The temperature inside the DPX-1300 is
lights up.
extremely high.
Check that the ventilation slots are not
covered.
FAN warning indicator
lights up.
Contact the store where the DPX-1300 was
purchased.
The fan is broken.
This unit uses a DMDTM chip for the picture display. Their highly accurate technology makes it possible to keep more than 99.99%
of effective pixels, however, unexpectedly it can produce less than 0.01% of ineffective pixels. In such a case, missing or flashing
of a few pixels can be found on the screen. These are characteristics of DMDTM , not mechanical problems.
11
Reference
English
61
16_DPX-1300_E.p65
61
9/20/05, 5:09 PM
Message display
Message
Condition
No Signal
The unit is not receiving or detecting any signal at the selected input jack. This message is
displayed together with the name of the input source selected with the INPUT button.
INPUT A (Component) (Example)
The input name selected by the INPUT button is displayed. It will turn off 2 seconds after
the signal has been input.
Out Of Range
The unit is not able to decode the PC or HDMI signal currently being input.
Unknown Format
The unit is not able to decode the video signal currently being input.
Auto Sync...
The unit is setting itself to the most appropriate configuration for the RGB signal currently
being received.
Memory 1—6 Now Processing
The memory setting number is displayed for two seconds.
The lamps has reached its recommended
replacement time. Please replace with a new
one.
This message is displayed when the power switch is turned on if the lamp running time
exceeds 2000 hours. Press the ESCAPE button to remove the message.
Press again to enter standby.
Press the STANDBY/ON button once more to place the unit in standby mode.
Lens Adjustment is locked.
This message will be displayed for two seconds if you press the V. POS, ZOOM, or FOCUS
button when [Lens Adjustment Lock] is set to [On].
Invalid Operation
Appears in the menu operation guide when you press an invalid button during menu
operation. This message will be displayed for two seconds.
The color temp is fixed
Appears in the menu operation guide when you try to change the settings for the color
temperature in the color temperature fixed mode.
Please wait
Appears in the menu screen when the unit requres few seconds for swiching process to the
selected menu item.
62
16_DPX-1300_E.p65
62
9/20/05, 5:09 PM
LED indicator meanings
LED indicator
State
STANDBY/ON (*) Unlit
LAMP
COVER
TEMP
FAN
Meaning
Electrical fault.
Lit red
Standby
Blinking green
Preparing for operation.
Lit green
Operating
Blinking red
Cooling the lamp.
Blinking red / blinking
red rapidly
Blinking red: Error in the LAMP/COVER/TEMP system
Blinking red rapidly: Error in the FAN system
Unlit
Normal
Blinking red
The lamp running time has exceeded 2000 hours.
Lit red
The lamp has burned out.
Unlit
Normal
Lit red
The lamp cover or the filter cover is not attached correctly.
Unlit
Normal
Lit red
The temperature of the lamp or the interior of the case is abnormally high.
Unlit
Normal
Lit red
The cooling fan has broken.
(*) This LED is also present on the front panel of the main unit.
11
Reference
English
63
16_DPX-1300_E.p65
63
9/20/05, 5:09 PM
Specifications
• Optical
Projection mode
DLPTM (DMDTM) type, 1280 X 720 pixels, 0.8 inch
Lens
f=24.3 – 38.9 mm F=2.7 – 5.0, Electronic zoom(x 1.6), Electronic focus, Electronic lens shift
Lamp
270 W SHP lamp
Screen size
60–200 inch (16:9)
Brightness
800 – 400 ANSI lm (depends on Iris Setting)
Contrast
2500:1 to 5000:1 (depends on Iris Setting)
• Input
Color system
NTSC, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, PAL60
VIDEO
Composite signal
1Vp-p/75 Ω, Negative sync
S VIDEO
S-Video signal
Y:1Vp-p/75 Ω, Negative sync
C:0.286 or 0.3Vp-p/75 Ω
D4 VIDEO
Component signal
Y with sync:1Vp-p/75 Ω, Negative sync
(480i, 576i, 480p, 576p)
Y with sync:1Vp-p/75 Ω, 3 values sync
(1035i, 1080i, 720p)
PB/CB, PR/CR:0.7Vp-p/75 Ω
INPUT A/INPUT B
Component signal
Y with sync:1Vp-p/75 Ω, Negative sync (480i, 576i, 480p, 576p)
Y with sync:1Vp-p/75 Ω, 3 values sync (1035i, 1080i, 720p)
PB/CB, PR/CR:0.7Vp-p/75 Ω
RGB signal
G with sync:1Vp-p/75 Ω, Negative sync
(480i, 576i, 480p, 576p)
G with sync:1Vp-p/75 Ω, 3 values sync
(1035i, 1080i, 720p)
G:0.7Vp-p/75 Ω
(When using HD/VD or SYNC)
B, R:0.7Vp-p/75 Ω
HD, VD:1–5Vp-p/2.2kΩ, positive and negative sync
SYNC:2Vp-p/2.2kΩ, Negative sync (with video signals) (480i, 576i)
SYNC:0.6–5Vp-p/2.2kΩ, Negative sync (without video signals)
(480i, 576i, 480p, 576p)
HDMI
Digital RGB/component signal
DVI
Digital RGB signal
• Controls
Remote
RS-232C (D-sub 9 pins)
Trigger
Wireless remote
+12 V/Max 200 mA when the power is on
1 in front, 1 at rear
Wired remote
1 input jack, 1 output jack
• General
Usable temperature range
5 °C – 35 °C
Usable humidity range
30 % – 85 %(There should be no condensation)
Power supply
AC100 – 120 V/220 – 240 V, 50/60 Hz
Power consumption
395 W
Power consumption in standby mode 0.1 W – 0.2 W
Noise level
30 dB(Standard mode), 28 dB(When Lamp Power Mode is set to 80)
Dimension
495(W) x 192.6(H) x 465.4(D) mm
Weight
14.0 kg
64
16_DPX-1300_E.p65
64
9/20/05, 5:09 PM
495
19"-1/2
FAN
TEMP
(257.5
10"-1/8)
PATTERN
ASPECT
ESCAPE
LAMP
COVER
STANDBY/ON
DIGITAL CINEMA PROJECTOR DPX-1000
INPUT
MENU
SETTING
237.5
9"-3/8
Dimensional drawing
119.1
4"-3/5
465.4
18"-5/16
192.6
7"-9/16
124.6
4"-7/8
132.1
5"-3/16
297.4
11"-3/4
DVI
INPUT B
RGB/YPBPR/YCBCR
HDMI
D4 VIDEO
G/Y
11
360
14"-3/16
Reference
HD/SYNC
VD
OUT
REMOTE
10
3/8
INPUT A
R/PR/CR
124
4"-7/8
B/PB/CB
IN
S VIDEO
RS-232C
VIDEO
TRIGGER OUT
Specifications are subject to change without notice.
This unit may interfere with reception if placed in close proximity to a radio or television receiver. Follow the instructions in this
manual to install the unit correctly.
65
16_DPX-1300_E.p65
65
9/20/05, 5:09 PM
English
•