ENGLISH
DEUTSCH
ACOUSTIC ECHO CANCELLER CARD
ESPAÑOL
ITALIANO
EN
DE
ES
IT
RU
ZH
取 扱 説 明書
中文
FR
JA
日本語
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manuale di istruzioni
Руководство пользователя
FRANÇAIS
MY4 - AEC
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used
according to the instructions found in the users manual,
may cause interference harmful to the operation of
other electronic devices. Compliance with FCC
regulations does not guarantee that interference will not
occur in all installations. If this product is found to be
the source of interference, which can be determined by
turning the unit “OFF” and “ON”, please try to eliminate
the problem by using one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(class B)
CANADA
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• This applies only to products distributed by Yamaha Canada Music Ltd.
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
(class B)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE
PROCEEDING
* Please keep this manual in a safe place for
future reference.
WARNING
Always follow the basic precautions listed below to
avoid the possibility of serious injury or even death
from electrical shock, short-circuiting, damages,
fire or other hazards. These precautions include, but
are not limited to, the following:
• Do not install the card in any Yamaha products not
specified by Yamaha for use with the card to avoid possible
electrical shock, fire, or equipment damage.
• Do not attempt to disassemble or modify the card. Do not
apply excessive force to card connectors or other card
components. Mishandling of the card may lead to shock,
fire hazard, or equipment failure.
• Be sure to disconnect the power cable of the host device
before installing the card and connecting/disconnecting the
cables (in order to eliminate shock hazard, undesired noise,
and avoid equipment damage).
• Turn off all peripheral devices connected to the host device
before installation, and unplug all related cables (in order
to eliminate shock hazard, undesired noise, and avoid
equipment damage).
CAUTION
These precautions include, but are not limited to,
the following:
• Be sure to properly ground the host device to prevent
electrical shock and/or malfunction.
• Do not touch the metallic leads (pins) of the circuit board
when handling the card. The pins are sharp and may cause
hand cuts.
• Wear a pair of heavy gloves during installation to avoid
scratching or cutting your hands on sharp edges.
• Avoid touching exposed connectors and metal parts to
minimize the possibility of bad connections.
• Drain all static electricity from your clothing and body
before handling the card. Static electricity can damage the
card. Touch an exposed metal part of the host device or
other grounded object beforehand.
• Do not drop the card or subject it to physical shock as this
can result in breakage and/or malfunction.
• Do not drop screws or other small parts inside the card. If
power is applied while screws or similar metal objects are
loose inside the unit the card may malfunction or be
damaged. If you cannot retrieve dropped objects yourself,
refer the problem to qualified Yamaha service personnel.
Yamaha cannot be held responsible for damage caused by
improper use or modifications to the device, or data that is
lost or destroyed.
• The illustrations as shown in this manual are for
instructional purposes only, and may be different from the
ones on your equipment.
• The company names and product names in this manual are
the trademarks or registered trademarks of their respective
companies.
Always follow the basic precautions listed below to
avoid the possibility of physical injury to you or
others, or damage to the device or other property.
MY4-AEC Owner’s Manual
3
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents
means that used electrical and electronic products should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products, please take them
to applicable collection points, in accordance with your national legislation and
the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier
for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact
your local authorities or dealer and ask for the correct method of disposal.
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Conforms to Environments: E1, E2, E3 and E4
4 MY4-AEC Owner’s Manual
Introduction
Thank you for choosing the Yamaha MY4-AEC. The MY4-AEC is an acoustic echo canceller
card designed for use with the DME64N/24N Digital Mixing Engines that can effectively reduce
troublesome acoustic echoes due to secondary pickup of speaker output and reflections from
room surfaces in teleconferencing situations. It is also capable of reducing feedback as well as
ambient noise from air conditioning and fans. This technology enables noise-free, highintelligibility teleconferencing in just about any environment. Four AES/EBU input and output
channels are provided, all with built-in sample rate conversion capability. The MY4-AEC can
also connect to digital audio devices that do not allow word clock synchronization.
Installation
Refer to the DME64N/24N owner’s manual for installation details. The screws on the left and
right sides of the card also ground (earth) the device, so be sure to tighten them securely.
Supplied Items
 Owner’s Manual (this document)
 3-pin Euroblock plugs x 4
 Cable ties x 4
MY4-AEC Owner’s Manual
5
Principle of Operation
How Acoustic Echo and Noise are Reduced
Acoustic echo occurs in a teleconferencing system when the sound from a speaker or
reflections from surfaces of the room are picked up by a microphone and transmitted to the
other party, resulting in a loss of intelligibility. Projectors and air conditioning systems also
produce noise that can interfere with clear teleconferencing. The echo cancelling and noise
reduction capabilities of the MY4-AEC help to achieve maximum clarity and intelligibility for
smooth, effective communication.
Remote
Local
“Hello”
“Hello”
“How’s business?”
DME64N/24N
SCENE
“How’s business?”
HOME
UTILITY
LEVEL
MUTE
CANCEL
ENTER
+
MY4-AEC
“How’s business”
+ “Hello”
+ fan noise
Fan noise
NOTE
In order to reduce acoustic echo originating from the remote location, an echo canceller must be
installed and active at the remote location.
6 MY4-AEC Owner’s Manual
MY4-AEC Signal Flow
The local and remote locations in a teleconferencing system are referred to as the “near end”
and “far end”, respectively. The MY4-AEC acoustic echo canceller (AEC) works by comparing
the reference signal received from the far-end with the signal from the microphone in order to
determine which components of the signal are echo, and then subtracts only the far-end echo
component from microphone signal. The near-end sound is thus clearly transmitted to the far
end without echo.
From Far-end A
From Far-end B
From Far-end C
From Far-end D
Far-end Voice A
Far-end Voice B
Far-end Voice C
Far-end Voice D
NR
NR
NR
NR
Matrix Router
To Far-end 4
To Far-end 3
To Far-end 2
To Far-end 1
NR
Near-end Mic. 3
FBS
Reference signal
Near-end Voice 3
Near-end Mic. 2
AEC
AEC
Near-end Voice 4
FBS
AEC
NR
NR
Near-end Mic. 4
AEC
NR
FBS
Near-end Voice 2
Near-end Mic. 1
FBS
Near-end Voice 1
FBS: Feedback suppressor
NR: Noise reduction
MY4-AEC Owner’s Manual
7
The Connectors and Their Functions
AES/EBU IN and OUT Connectors
These connectors support four channels of AES/EBU format digital audio input and output to
and from the host DME64N/24N unit, but those signals are not directly routed via the MY4-AEC
processing section. Signals from the host’s analog or digital inputs must be routed to the MY4AEC card’s AEC processing section via the host’s processing section in order to apply echo
cancellation, as shown in the illustration below. Operational details are provided in the DME
Designer owner’s manual. Built-in sample rate conversion is provided for all inputs and outputs
(sample rate conversion settings are also made via the DME Designer software).
Use the supplied Euroblock plugs for connection (refer to “Euroblock Connection” on
page 10).
NOTE
The channel 3 and channel 4 inputs and outputs ([IN3/4] and [OUT3/4] in the above illustration)
cannot be used when the DME64N/24N word clock sampling rate is set to 88.2 kHz or 96 kHz.
8 MY4-AEC Owner’s Manual
DME Processing
DME64N/24N
AEC
Processing
MY4-AEC
SRC
Analog Out
Mic In
AES/EBU
[OUT1/2][OUT3/4]
SRC
AES/EBU
[IN1/2][IN3/4]
MY4-AEC Owner’s Manual
9
Euroblock Connection
Please be sure to use the supplied Euroblock plugs to connect the AES/EBU [IN] and [OUT]
connectors.
Cable preparation
• To prepare the cable for attachment to a Euroblock
approx.
7 mm
connector, strip the wire as shown in the illustration
using stranded wire to make connections. With a
Euroblock connection, stranded wires may be prone to
breakage because of metal fatigue due to the weight of
the cable or due to vibration. Bundle the cables and the
Euroblock tabs using the supplied cable ties (page 12). When rackmounting your
equipment, use a lacing bar when possible to bundle and fasten the cables.
NOTE
Do not tin (plate with solder) the exposed end.
• If cables will be frequently connected and
disconnected, as in the case of a portable installation,
we recommend that you use ferrules with insulation
sleeves. Use a ferrule whose conductor portion has an
external diameter of 1.6 mm or less, and a length of
approximately 7 mm (such as the AI0,5-6WH made by
the Phoenix Contact corporation).
10 MY4-AEC Owner’s Manual
1.6 mm or less
approx.
7 mm
1
Loosen terminal screws.
2
Insert cables.
Loosen.
Slotted
Screwdriver
+
–
Terminal
Screw
G
Euroblock
Plug
Tab
NOTE
3
Securely tighten terminal
screws.
Pull the cables (not too strongly) to
confirm that they are securely
connected.
A slotted screwdriver with a blade width of
about 3 millimeters is recommended.
3mm or less
MY4-AEC Owner’s Manual
11
4
Bundle the cables and the
Euroblock tab using the
supplied cable tie.
NOTE
Trim any excess part of the cable tie as
necessary.
12 MY4-AEC Owner’s Manual
5
Insert the Euroblock plug into
the AES/EBU [IN] or [OUT]
connector of the MY4-AEC.
Basic Connection and Setup
Example 1: Teleconferencing with a Remote Location
This is an example of a teleconferencing system set up to allow multiple participants to hold
conferences with a remote location (“Office X”).
Preparation
The first step is to make the basic local (near end) connections and determine the optimum
microphone and speaker locations as well as gain settings. The AEC system will have the best
possible effect if these initial steps are carried out properly.
1
Prepare the following equipment.
 DME24N x 1
 MY4-AEC x 1
 Microphones x 4
 Speakers x 2
NOTE
Be sure to choose microphones and speakers that have good frequency response characteristics
in order to ensure optimum AEC operation.
2
Connect the microphones and speakers to the analog [IN] and [OUT]
connectors on the DME24N rear panel as shown in the diagram.
MY4-AEC Owner’s Manual
13
Meeting Room (Near End)
Microphone 1
Speaker 1
OUT
(Analog)
Microphone 2
Speaker 2
Microphone 3
Microphone 4
DME24N
+
MY4-AEC
IN (Analog)
3
Make the required virtual connections in the DME Designer configuration
window.
• Connect the signals from microphone inputs 1 – 4 to the “Near-end Mic. 1” – “Near-end
Mic. 4” inputs on the AEC component.
• Place an oscillator that will be used for AEC adjustment in the configuration window and
connect it to the AEC component “From Far-end A” input.
• The “Far-end voice A” output is connected to the conference room speakers (SP 1 and
SP 2) in parallel.
14 MY4-AEC Owner’s Manual
4
Speak into the microphones as you would during an actual conference
and adjust the input gain of each channel.
Adjust the DME24N HA Gain while watching the “Mic. In” meters in the AEC component
editor so that the yellow segment lights only occasionally.
NOTE
AEC may not function properly if the gain is set too high.
MY4-AEC Owner’s Manual
15
5
Open the Oscillator component editor, set the Wave Form type to “Pink,”
and engage the Output section “On” button.
Go back to the AEC component editor and, while watching the “Ref. In” meter, adjust the
oscillator output level so that the yellow segment lights only occasionally.
16 MY4-AEC Owner’s Manual
6
Check that the ERL (Echo Return Loss) meter in the AEC component is
moving.
If this meter is moving over a wide range it means that a large portion of the pink noise
being output from the speaker is being picked up by the corresponding microphone, and
therefore a large amount of echo will be transmitted to the remote location. Carefully adjust
the positions and pickup directions of the four microphones in relation to the speakers in
order to reduce this echo level as much as possible. The more you can reduce the echo at
this stage, the more effective the AEC will be.
NOTE
• If the local meeting room is very reflective or reverberant, it may be difficult to reduce the echo
level sufficiently by simply repositioning the microphones and speakers. In such cases it may
be necessary to apply acoustic panels to the walls or use other means to reduce room
reflections.
• If only the green segment of the ERL meter lights, setting the “Effect” parameter to 1 or 2 should
be optimum, but if the yellow segment of the ERL meter lights an “Effect” setting of 3 or 4 will be
required to produce the best results. Since the actual effectiveness of the processing will
depend on the rooms in which it is used it is important make adjustments while actually
connected to and conferring with the remote location.
• If the input signal becomes distorted for any reason before it reaches the Near-end Mic. 1 – 4
inputs of the AEC component, echo cancelling will not function properly.
7
Enter the microphone-to-speaker distance in meters into the Acoustic
Echo Canceller section “Distance” field.
If multiple speakers are used, enter the distance between the microphone and nearest
speaker for each channel.
If the distance is less than 2 meters, use the default value of “2”. For greater distances
enter the appropriate value.
MY4-AEC Owner’s Manual
17
Remote Connection and Settings
1
Connect the microphones, speakers, and teleconferencing system to the
analog [IN] and [OUT] connectors on the rear panel of the DME24N as
shown in the diagram.
Four microphones can be connected at the near-end location, allowing multiple
conference participants.
Meeting Room (Near End)
Speaker 1
Microphone 1
Office X
(Remote –
Far End)
Speaker 2
Microphone 2
OUT
(Analog)
Microphone 3
DME24N
+
MY4-AEC
IN (Analog)
Network
IN/OUT (Analog)
Teleconferencing system
18 MY4-AEC Owner’s Manual
Microphone 4
2
Make the required virtual connections in the DME Designer configuration
window.
• Connect the signal from the four local microphones (Mic1 – Mic4) and the audio signal
from the remote location (From Office X) to the appropriate inputs of the AEC
component.
• Mix the “Near-end Voice 1” – “Near-end Voice 4” outputs and the “Far-end Voice A”
outputs from the AEC component and connect the mixed output in parallel to the
meeting room speakers (SP 1 and SP 2).
• Mix the “To Far-end 1” – “To Far-end 4” outputs from the AEC component and connect
the mixed output to “To Office X” for transmission to the remote location.
HINT
When multiple speakers are being used in the local meeting room, be sure to connect the
mixed signal to them in parallel. AEC may not function properly if the output balance
between the speakers changes.
MY4-AEC Owner’s Manual
19
3
Adjust the DME Designer AEC component editor parameters so that
acoustic echo is effectively cancelled from the audio signal sent to Office
X.
Begin by checking that the connection with Office X is working properly and that
conversation is possible. If echo can be heard with the default AEC section Effect setting
of “1”, try increasing the setting in small increments. Echo cancellation efficiency will
increase as the setting is increased, but sound quality will decrease at the same time so it
is necessary to find the best setting for conditions in the local meeting room while actually
listening to the audio signal.
Other parameters can usually be left at their default settings. Refer to the DME Designer
owner’s manual for details on the individual AEC component parameters.
20 MY4-AEC Owner’s Manual
Example 2: Teleconferencing with Two Remote
Locations from Two Meeting Rooms
Using one MY4-AEC card, multiple participants in two meeting rooms can teleconference with
two separate remote locations (“Office X” and “Office Y”).
Preparation
Referring to Example 1, use an oscillator component to determine the ideal microphone and
speaker positions for each meeting room.
The following equipment is used.
 DME24N x 1
 MY4-AEC x 1
 Microphones x 4
 Speakers x 4
Remote Connection and Settings
1
Connect the microphones, speakers, and teleconferencing system to the
analog [IN] and [OUT] connectors on the rear panel of the DME24N as
shown in the diagram.
A total of four microphones can be connected for the medium and small near-end meeting
rooms, allowing multiple participants to confer simultaneously in both rooms.
MY4-AEC Owner’s Manual
21
Small Meeting Room (Near End)
Office X
(Remote –
Far End)
Speaker 1
Microphone 1
Teleconferencing
system
Speaker 2
Microphone 2
OUT (Analog)
Network
IN/OUT
(Analog)
DME24N
IN (Analog)
+
IN/OUT
(Analog)
Network
MY4-AEC
OUT (Analog)
Speaker 1
Office Y
(Remote –
Far End)
Teleconferencing
system
Speaker 2
Medium Meeting Room (Near End)
22 MY4-AEC Owner’s Manual
IN (Analog)
Microphone 1
Microphone 2
2
Make the required virtual connections in the DME Designer configuration
window.
• Connect the signal from the microphones in the small and medium local meeting rooms
(Conf S Mic1/2 and Conf M – Mic1/2) and the audio signal from the remote locations
(From Office X and From Office Y) to the appropriate inputs of the AEC component.
• Mix the “Near-end Voice 1” and “Near-end Voice 2” outputs and the “Far-end Voice A”
outputs from the AEC component and connect the mixed output in parallel to the small
meeting room speakers (Conf S SP 1 and SP 2).
• Mix the “Near-end Voice 3” and “Near-end Voice 4” outputs and the “Far-end Voice B”
outputs from the AEC component and connect the mixed output in parallel to the
medium meeting room speakers (Conf M SP 1 and SP 2).
• Mix the “To Far-end 1” and “To Far-end 2” outputs from the AEC component and connect
the mixed output to “To Office X” for transmission to remote Office X.
• Mix the “To Far-end 3” and “To Far-end 4” outputs from the AEC component and connect
the mixed output to “To Office Y” for transmission to remote Office Y.
HINT
When multiple speakers are being used in the same meeting room, be sure to connect the
mixed signal to them in parallel. AEC may not function properly if the output balance
between the speakers changes.
MY4-AEC Owner’s Manual
23
3
In the Matrix Router section of the AEC component editor, select one or
more of the “From Far-end A – D signals” to be used as the reference for
each AEC channel 1 – 4.
The “On” buttons in the Matrix Router section can be used to select microphones and
locations for each meeting room.
For this example the Matrix Router is set as shown below. With these settings it is possible
to simultaneously hold independent conferences between the small meeting room and
Office X (Far-end A) using AEC channels 1 and 2, and between the medium meeting room
and Office Y (Far-end B) using AEC channels 3 and 4.
From
Far-end A
From
Far-end B
24 MY4-AEC Owner’s Manual
Appendix
Specifications
 GENERAL SPECIFICATIONS
Sampling Frequency
44.1kHz-10% to 48kHz+6%,
88.2kHz-10% to 96kHz+6%
Power requirements
5V :
395mA
3.3V : 295mA
Temperature Range
Operating
0 to +40°C
Storage
-20 to +60°C
Weight
160g
 DIGITAL INPUT/OUTPUT CHARACTERISTICS
Terminal
IN
1/2, 3/4
OUT 1/2, 3/4
Format
Audio Data Length
Level
Connector
AES/EBU
24bit
RS422
Euroblock
AES/EBU
(Professional use)
24bit
RS422
Euroblock
MY4-AEC Owner’s Manual
183
Dimensions
164.1 176.1
(12)
120
40
unit: mm
184 MY4-AEC Owner’s Manual
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp.
reserves the right to change or modify products or specifications at any time without prior notice. Since
specifications, equipment or options may not be the same in every locale, please check with your Yamaha
dealer.
* Die technischen Daten und Beschreibungen in dieser Bedienungsanleitung dienen nur der Information.
Yamaha Corp. behält sich das Recht vor, Produkte oder deren technische Daten jederzeit ohne vorherige
Ankündigung zu verändern oder zu modifizieren. Da die technischen Daten, das Gerät selbst oder
Sonderzubehör nicht in jedem Land gleich sind, setzen Sie sich im Zweifel bitte mit Ihrem Yamaha-Händler in
Verbindung.
* Les caractéristiques techniques et les descriptions du mode d’emploi ne sont données que pour information.
Yamaha Corp. se réserve le droit de changer ou modifier les produits et leurs caractéristiques techniques à
tout moment sans aucun avis. Du fait que les caractéristiques techniques, les équipements et les options
peuvent différer d’un pays à l’autre, adressez-vous au distributeur Yamaha le plus proche.
* Las especificaciones y descripciones de este manual del propietario tienen sólo el propósito de servir como
información. Yamaha Corp. se reserva el derecho a efectuar cambios o modificaciones en los productos o
especificaciones en cualquier momento sin previo aviso. Puesto que las especificaciones, equipos u
opciones pueden no ser las mismas en todos los mercados, solicite información a su distribuidor Yamaha.
* Le specifiche e le descrizioni presenti in questo manuale sono fornite a fini puramente informativi. Yamaha
Corp. si riserva il diritto di modificare prodotti o specifiche in qualsiasi momento senza preavviso. Dato che le
specifiche, le apparecchiature o le opzioni possono essere diverse da paese a paese, verificarle con il proprio
rappresentante Yamaha.
* 仕様および外観は改良のため、予告なく変更することがあります。
MY4-AEC Owner’s Manual
185
Memo
186 MY4-AEC Owner’s Manual
Memo
MY4-AEC Owner’s Manual
187
188 MY4-AEC Owner’s Manual
MY4-AEC Owner’s Manual
189
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso No.7, Marbella, Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park,
CA 90620, U.S.A.
Tel: 714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col.
San José Insurgentes, Delegación Benito
Juárez, México, D.F., C.P. 03900
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4º andar,
Itaim Bibi, CEP 04534-013 São Paulo,
SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
VENEZUELA
Yamaha Music Latin America, S.A.,
Sucursal Venezuela
C.C. Manzanares Plaza P4
Ofic. 0401- Manzanares-Baruta
Caracas Venezuela
Tel: 58-212-943-1877
EUROPE
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton
Keynes, MK7 8BL, U.K.
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen,
Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH
Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern
Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
POLAND/LITHUANIA/LATVIA/
ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office
ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
190 MY4-AEC Owner’s Manual
MALTA
Olimpus Music Ltd.
The Emporium, Level 3, St. Louis Street
Msida MSD06
Tel: 02133-2144
NETHERLANDS/BELGIUM/LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen,
Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activites
Pariest, 77183 Croissy-Beaubourg,
France
Tel: 01-64-61-4000
ITALY
Yamaha Music Europe GmbH,
Branch Italy
Viale Italia 88, 20020 Lainate (Milano),
Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha Music Europe GmbH
Ibérica, Sucursal en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas (Madrid), Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music
House
147 Skiathou Street, 112-55 Athens,
Greece
Tel: 01-228 2160
SWEDEN/FINLAND/ICELAND
Yamaha Music Europe GmbH Germany filial Scandinavia
J. A. Wettergrensgata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: +46 31 89 34 00
DENMARK
Yamaha Music Europe GmbH,
Tyskland – filial Denmark
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Yamaha Music Europe GmbH Germany - Norwegian Branch
Grini Næringspark 1, N-1361 Østerås,
Norway
Tel: 67 16 78 00
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, bld. 7, Kievskaya street, Moscow, 121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen,
Germany
Tel: +49-4101-3030
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, UAE
Tel: +971-4-881-5868
Yamaha Music & Electronics
(China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China
Tel: 021-6247-2211
INDIA
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower
A, Sector 47, Gurgaon- Sohna Road,
Gurgaon, Haryana, India
Tel: 0124-485-3300
INDONESIA
Yamaha Music Center Bldg. Jalan Jend.
Gatot Subroto Kav. 4, Jakarta 12930,
Indonesia
Tel: 021-520-2577
KOREA
MIDDLE EAST
Yamaha Music Korea Ltd.
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul
Şubesi
Maslak Meydan Sokak No:5 Spring Giz
Plaza Bağımsız Böl. No:3, 34398 Şişli
İstanbul
Tel: +90-212-999-8010
CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen,
Germany
Tel: 04101-3030
OTHER COUNTRIES
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, U.A.E
Tel: +971-4-881-5868
PA36
THE PEOPLE’S REPUBLIC OF
CHINA
PT. Yamaha Musik Indonesia (Distributor)
AFRICA
Yamaha Music Gulf FZE
ASIA
8F, 9F, Dongsung Bldg. 158-9 SamsungDong, Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn.,
Bhd.
No.8, Jalan Perbandaran, Kelana Jaya,
47301
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 65-6747-4374
TAIWAN
Yamaha Music & Electronics Taiwan Co.,Ltd.
3F, No.6, Section 2 Nan-Jing East Road,
Taipei, Taiwan R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15 and 16th floor, Siam Motors
Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
VIETNAM
Yamaha Music Vietnam Company
Limited
15th Floor, Nam A Bank Tower, 201-203
Cach Mang Thang Tam St., Ward 4,
Dist.3, Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2312
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC
OCEAN
Yamaha Corporation,
Asia-Pacific Music Marketing
Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2313
HEAD OFFICEYamaha Corporation, Audio Products Sales and Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
MY4-AEC Owner’s Manual
191
ENGLISH
DEUTSCH
ACOUSTIC ECHO CANCELLER CARD
http://www.yamahaproaudio.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
312YJTO-B0
Printed in Japan
WW75420
ESPAÑOL
ITALIANO
EN
DE
ES
IT
RU
ZH
取扱説明書
中文
FR
JA
日本語
Yamaha Pro Audio global web site
C.S.G., PA Development Division
© 2011-2013 Yamaha Corporation
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manuale di istruzioni
Руководство пользователя
FRANÇAIS
MY4 - AEC