Epson PowerLite home cinema 3010e User`s guide

PowerLite Home Cinema 3010/3010e
®
Quick Setup
Computer
HDMI cable
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Choose a location
Keep the projector level and place it at a height where its lens is centered
between the top and bottom of the screen. If this isn’t possible, use the
horizontal keystone slider and keystone correction buttons to reposition the
image (see “Adjust the image”).
In order to view 3D images correctly, 3D glasses must be worn within proper
range of the projector. Use the image below to determine the ideal distance for
3D projection (the shading represents the 3D viewing area):
Adjust the image
Using the remote control
1If you don’t see an image, press the Source buttons on the projector or
Make sure the batteries are installed as shown (two AA batteries).
the remote control to select the image source.
VGA cable
Monitor Port
Connect one end of a VGA cable to the projector’s PC port, and the other end
to your computer’s
monitor port. If you are using a laptop, switch it to
external display (see “Troubleshooting”). You can also connect an audio cable.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2To raise the image, adjust the front feet as shown below.
HDMI Port
Connect one end of an HDMI cable to the projector’s HDMI port and the other
end to an HDMI port on your computer.
Camera or USB Device
Turn projector on
3
Connect a digital camera, USB flash drive, or USB storage device to the
projector’s�
USB
���������
port.
Turn projector off
Choose which source
to display
Turn the zoom ring to reduce or enlarge the image.
Switch between
2D and 3D
Navigate projector
menus
60º
Access projector
menus
16.5 ft (5 m)
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature to project images. See the online User’s
Guide for details.
13 ft (4 m)
Use the optional external 3D emitter if the projector is located over
16.5 feet (5 m) from the viewing area. See “Optional accessories” on the back
of this sheet for ordering information, and the online User’s Guide for more
information on where to place your projector.
Connect the projector
4Turn the focus ring to sharpen the image.
Turn off projector
display
Turn on your equipment
1
Turn on your video source or computer.
2
Plug in the projector. The
power button on the projector turns blue.
Choose from the following connections. See the sections below or the online
User's Guide for details.
For more information on using the remote control, see the online User’s
Guide.
5If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Use the horizontal keystone slider on
the projector to correct it. Or place the projector directly in front of the
center of the screen, facing the screen squarely.
Project wirelessly
(PowerLite Home Cinema 3010e only)
Follow these steps to use the included WirelessHD Transmitter (PowerLite
Home Cinema 3010e only) to wirelessly transmit HD content to your projector.
Video Device
Connect up to 5 video devices and use the Source buttons on the projector or
remote control to switch between them.
HDMI cable
3
Remove the lens cap.
6Your projector automatically adjusts images that look like
RCA Video cable
but if necessary you can press the
correct this.
or
or
,
buttons on the projector to
1Place the transmitter within 30 feet (10 m) of the projector. Make sure
the front of the transmitter faces the front of the projector. See the
online User’s Guide for more information on the WirelessHD transmission
range.
Audio cable
Note: Do not place the transmitter on a metal surface, as this may
interfere with the signal.
Component video cable
4Press the
power button on the projector or On button on the remote
control. The power light flashes blue, and then stays on.
2
Plug the AC adapter into the transmitter and a wall outlet.
3Connect an HDMI cable to your video device and the HDMI port on the
Audio cable
side of the transmitter.
Note: To shut down the projector, press the
power button on the
projector twice or the Standby button on the remote control, then
unplug it. You don’t have to wait for the projector to cool down.
5The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select Extended
and press Enter. Select Language and press Enter. Select your language
and press Enter. Press the Menu button to exit the menu system.
*412153700*
*412153700*
4
Turn on the power switch on the back of the transmitter.
5
Turn on your video device and begin playback.
6
Turn on the projector.
7
Press the
button on the projector remote control.
See the online User’s Guide for more information on adjusting and configuring
the WirelessHD connection.
PowerLite Home Cinema 3010/3010e
®
Quick Setup
Computer
HDMI cable
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Choose a location
Keep the projector level and place it at a height where its lens is centered
between the top and bottom of the screen. If this isn’t possible, use the
horizontal keystone slider and keystone correction buttons to reposition the
image (see “Adjust the image”).
In order to view 3D images correctly, 3D glasses must be worn within proper
range of the projector. Use the image below to determine the ideal distance for
3D projection (the shading represents the 3D viewing area):
Adjust the image
Using the remote control
1If you don’t see an image, press the Source buttons on the projector or
Make sure the batteries are installed as shown (two AA batteries).
the remote control to select the image source.
VGA cable
Monitor Port
Connect one end of a VGA cable to the projector’s PC port, and the other end
to your computer’s
monitor port. If you are using a laptop, switch it to
external display (see “Troubleshooting”). You can also connect an audio cable.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2To raise the image, adjust the front feet as shown below.
HDMI Port
Connect one end of an HDMI cable to the projector’s HDMI port and the other
end to an HDMI port on your computer.
Camera or USB Device
Turn projector on
3
Connect a digital camera, USB flash drive, or USB storage device to the
projector’s�
USB
���������
port.
Turn projector off
Choose which source
to display
Turn the zoom ring to reduce or enlarge the image.
Switch between
2D and 3D
Navigate projector
menus
60º
Access projector
menus
16.5 ft (5 m)
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature to project images. See the online User’s
Guide for details.
13 ft (4 m)
Use the optional external 3D emitter if the projector is located over
16.5 feet (5 m) from the viewing area. See “Optional accessories” on the back
of this sheet for ordering information, and the online User’s Guide for more
information on where to place your projector.
Connect the projector
4Turn the focus ring to sharpen the image.
Turn off projector
display
Turn on your equipment
1
Turn on your video source or computer.
2
Plug in the projector. The
power button on the projector turns blue.
Choose from the following connections. See the sections below or the online
User's Guide for details.
For more information on using the remote control, see the online User’s
Guide.
5If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Use the horizontal keystone slider on
the projector to correct it. Or place the projector directly in front of the
center of the screen, facing the screen squarely.
Project wirelessly
(PowerLite Home Cinema 3010e only)
Follow these steps to use the included WirelessHD Transmitter (PowerLite
Home Cinema 3010e only) to wirelessly transmit HD content to your projector.
Video Device
Connect up to 5 video devices and use the Source buttons on the projector or
remote control to switch between them.
HDMI cable
3
Remove the lens cap.
6Your projector automatically adjusts images that look like
RCA Video cable
but if necessary you can press the
correct this.
or
or
,
buttons on the projector to
1Place the transmitter within 30 feet (10 m) of the projector. Make sure
the front of the transmitter faces the front of the projector. See the
online User’s Guide for more information on the WirelessHD transmission
range.
Audio cable
Note: Do not place the transmitter on a metal surface, as this may
interfere with the signal.
Component video cable
4Press the
power button on the projector or On button on the remote
control. The power light flashes blue, and then stays on.
2
Plug the AC adapter into the transmitter and a wall outlet.
3Connect an HDMI cable to your video device and the HDMI port on the
Audio cable
side of the transmitter.
Note: To shut down the projector, press the
power button on the
projector twice or the Standby button on the remote control, then
unplug it. You don’t have to wait for the projector to cool down.
5The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select Extended
and press Enter. Select Language and press Enter. Select your language
and press Enter. Press the Menu button to exit the menu system.
*412153700*
*412153700*
4
Turn on the power switch on the back of the transmitter.
5
Turn on your video device and begin playback.
6
Turn on the projector.
7
Press the
button on the projector remote control.
See the online User’s Guide for more information on adjusting and configuring
the WirelessHD connection.
Viewing 3D images
Where to get help
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector. You will also need a pair of Epson or
Epson-compatible 3D active shutter glasses.
Manual
1
Turn on and begin playback on the 3D-compatible video device.
2
Press the
3
For more information about using the projector, click the icon on your desktop
to access the online manual (requires an Internet connection). If you don’t have
a User's Guide icon, you can install it from the projector CD or go to the Epson
website, as described below.
button on the projector remote control, if necessary.
Press and hold the power button on your 3D glasses for at least one
second.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter the
PIN on the Epson PrivateLine Support card included with your projector. This
service is available 6 am to 6 pm, Pacific Time, Monday through Friday, for the
duration of your warranty period. You may also speak with a projector support
specialist by dialing:
US: (562) 276-4394, 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday
See the online User’s Guide for more information on adjusting the 3D images.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
Canada: (905) 709-3839, 6
am
to 8
pm,
Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
•Make sure the power light on the projector is blue and not flashing.
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
•
Registration
•
•
Press the Source buttons on the projector or the remote control to
switch to the correct image source, if necessary.
If you’re using a Windows® laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
If you’re using a Mac® laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays check box.
If 3D images aren’t displaying properly, check the following:
•
Press the
•
Make sure that you are within the 3D viewing range. See “Choose a
location” on the front of this sheet or the online User’s Guide for more
information.
•
•
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens or other accessories from an Epson authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you
can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca
(Canadian sales).
button to switch to 3D viewing mode, if necessary.
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option is
selected.
Check that your video device and media are both 3D compatible. Refer
to the documentation that came with your video device for more
information.
Notices
Declaration of Conformity
According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals;
and/or CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at: Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein, complies
with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each
product marketed, is identical to the representative unit tested and found
to be compliant with the standards. Records maintained continue to reflect
the equipment being produced can be expected to be within the variation
accepted, due to quantity production and testing on a statistical basis as
required by 47CFR 2.909. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Epson America, Inc. Limited Warranty
In Canada, warranties include both warranties and conditions.
Two-Year Projector Limited Warranty and 90-Day Lamp Limited Warranty
Some jurisdictions do not allow limitations on how long an implied warranty
lasts and some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights, which vary from jurisdiction to jurisdiction.
What Is Covered: Epson America, Inc. ("Epson") warrants to the original retail
purchaser of the Epson projector product enclosed with this limited warranty
statement that the product, if purchased new and operated in the United
States, Canada, or Puerto Rico will be free from defects in workmanship and
materials for a period of two (2) years from the date of original purchase. This
limited warranty applies only to the projector and not to the projector lamp,
which carries a limited warranty period of ninety (90) days from the date of
original purchase. For warranty service, you must provide proof of the date of
original purchase.
What Epson Will Do To Correct Problems: If your product requires service
during the limited warranty period, please call Epson at the number on the
bottom of this statement and be prepared to provide the model, serial number,
and date of original purchase. Epson will, at its option, repair or replace
the defective unit, without charge for parts or labor. When warranty service
involves the exchange of the product or of a part, the item replaced becomes
Epson property. The exchanged product or part may be new or refurbished to
the Epson standard of quality, and at Epson’s option, the replacement may be
another model of like kind and quality. Epson’s liability for replacement of the
covered product will not exceed the original retail selling price of the covered
product. Exchange or replacement products or parts assume the remaining
warranty period of the product covered by this limited warranty. If Epson
replaces the lamp as part of the warranty service, the replacement lamp carries
the limited 90-day warranty stated above.
To find the Epson Authorized Reseller nearest you, please visit our website at:
www.epson.com.
To find the Epson Customer Care Center nearest you, please visit
www.epson.com/support.
To contact the Epson ConnectionSM , please call (800) 637-7661 + PIN or
(562) 276-4394 in the U.S. and (905) 709-3839 in Canada or write to
Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012.
What This Warranty Does Not Cover: This warranty covers only normal use in
the United States, Canada or Puerto Rico. Twenty-four hours per day or other
excessive continual use is not considered normal use. This warranty does not
cover consumables such as filters. This warranty is not transferable. Epson is not
responsible for warranty service should the Epson label or logo or the rating
label or serial number be removed. Epson is not responsible for warranty service
should the product fail to be properly maintained or fail to function properly
as a result of misuse, abuse, improper installation, neglect, improper shipping,
damage caused by disasters such as fire, flood, and lightning, improper
electrical current, software problems, interaction with non-Epson products,
or service other than by Epson or an Epson Authorized Servicer. Postage,
insurance, or shipping costs incurred in presenting your Epson product for carryin warranty service are your responsibility. Epson will pay for all freight charges
if you choose to send your unit to Epson for repair. If a claimed defect cannot
be identified or reproduced in service, you will be held responsible for costs
incurred.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN
LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED
WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE.
UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY
ANY OTHER PERSON OR FIRM ARE VOID. IN THE EVENT THE REMEDIES ABOVE
FAIL, EPSON’S ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE
PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS LIMITED WARRANTY.
EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA,
INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE,
OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON
PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER
LEGAL THEORY.
Trade Name: EPSON
Type of Product: LCD Projector
Model:
H421A/H450A
Marketing Name:PowerLite Home Cinema 3010/PowerLite Home Cinema 3010e
Trade Name:
EPSON
Type of Product: WirelessHD Transmitter
Model:
AW-WH036TU/AW-WH036TE/AW-WH036TT
Marketing Name:WirelessHD Transmitter
Epson and PowerLite are registered trademarks, and Epson Exceed Your Vision is a registered logomark of
Seiko Epson Corporation. PrivateLine is a registered trademark and Epson Connection is a service mark of Epson
America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2011 Epson America, Inc. 7/11
Printed in XXXXXX
CPD-34999
Viewing 3D images
Where to get help
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector. You will also need a pair of Epson or
Epson-compatible 3D active shutter glasses.
Manual
1
Turn on and begin playback on the 3D-compatible video device.
2
Press the
3
For more information about using the projector, click the icon on your desktop
to access the online manual (requires an Internet connection). If you don’t have
a User's Guide icon, you can install it from the projector CD or go to the Epson
website, as described below.
button on the projector remote control, if necessary.
Press and hold the power button on your 3D glasses for at least one
second.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter the
PIN on the Epson PrivateLine Support card included with your projector. This
service is available 6 am to 6 pm, Pacific Time, Monday through Friday, for the
duration of your warranty period. You may also speak with a projector support
specialist by dialing:
US: (562) 276-4394, 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday
See the online User’s Guide for more information on adjusting the 3D images.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
Canada: (905) 709-3839, 6
am
to 8
pm,
Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
•Make sure the power light on the projector is blue and not flashing.
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
•
Registration
•
•
Press the Source buttons on the projector or the remote control to
switch to the correct image source, if necessary.
If you’re using a Windows® laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
If you’re using a Mac® laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays check box.
If 3D images aren’t displaying properly, check the following:
•
Press the
•
Make sure that you are within the 3D viewing range. See “Choose a
location” on the front of this sheet or the online User’s Guide for more
information.
•
•
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens or other accessories from an Epson authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you
can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca
(Canadian sales).
button to switch to 3D viewing mode, if necessary.
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option is
selected.
Check that your video device and media are both 3D compatible. Refer
to the documentation that came with your video device for more
information.
Notices
Declaration of Conformity
According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals;
and/or CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at: Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein, complies
with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each
product marketed, is identical to the representative unit tested and found
to be compliant with the standards. Records maintained continue to reflect
the equipment being produced can be expected to be within the variation
accepted, due to quantity production and testing on a statistical basis as
required by 47CFR 2.909. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Epson America, Inc. Limited Warranty
In Canada, warranties include both warranties and conditions.
Two-Year Projector Limited Warranty and 90-Day Lamp Limited Warranty
Some jurisdictions do not allow limitations on how long an implied warranty
lasts and some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights, which vary from jurisdiction to jurisdiction.
What Is Covered: Epson America, Inc. ("Epson") warrants to the original retail
purchaser of the Epson projector product enclosed with this limited warranty
statement that the product, if purchased new and operated in the United
States, Canada, or Puerto Rico will be free from defects in workmanship and
materials for a period of two (2) years from the date of original purchase. This
limited warranty applies only to the projector and not to the projector lamp,
which carries a limited warranty period of ninety (90) days from the date of
original purchase. For warranty service, you must provide proof of the date of
original purchase.
What Epson Will Do To Correct Problems: If your product requires service
during the limited warranty period, please call Epson at the number on the
bottom of this statement and be prepared to provide the model, serial number,
and date of original purchase. Epson will, at its option, repair or replace
the defective unit, without charge for parts or labor. When warranty service
involves the exchange of the product or of a part, the item replaced becomes
Epson property. The exchanged product or part may be new or refurbished to
the Epson standard of quality, and at Epson’s option, the replacement may be
another model of like kind and quality. Epson’s liability for replacement of the
covered product will not exceed the original retail selling price of the covered
product. Exchange or replacement products or parts assume the remaining
warranty period of the product covered by this limited warranty. If Epson
replaces the lamp as part of the warranty service, the replacement lamp carries
the limited 90-day warranty stated above.
To find the Epson Authorized Reseller nearest you, please visit our website at:
www.epson.com.
To find the Epson Customer Care Center nearest you, please visit
www.epson.com/support.
To contact the Epson ConnectionSM , please call (800) 637-7661 + PIN or
(562) 276-4394 in the U.S. and (905) 709-3839 in Canada or write to
Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012.
What This Warranty Does Not Cover: This warranty covers only normal use in
the United States, Canada or Puerto Rico. Twenty-four hours per day or other
excessive continual use is not considered normal use. This warranty does not
cover consumables such as filters. This warranty is not transferable. Epson is not
responsible for warranty service should the Epson label or logo or the rating
label or serial number be removed. Epson is not responsible for warranty service
should the product fail to be properly maintained or fail to function properly
as a result of misuse, abuse, improper installation, neglect, improper shipping,
damage caused by disasters such as fire, flood, and lightning, improper
electrical current, software problems, interaction with non-Epson products,
or service other than by Epson or an Epson Authorized Servicer. Postage,
insurance, or shipping costs incurred in presenting your Epson product for carryin warranty service are your responsibility. Epson will pay for all freight charges
if you choose to send your unit to Epson for repair. If a claimed defect cannot
be identified or reproduced in service, you will be held responsible for costs
incurred.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN
LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED
WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE.
UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY
ANY OTHER PERSON OR FIRM ARE VOID. IN THE EVENT THE REMEDIES ABOVE
FAIL, EPSON’S ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE
PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS LIMITED WARRANTY.
EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA,
INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE,
OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON
PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER
LEGAL THEORY.
Trade Name: EPSON
Type of Product: LCD Projector
Model:
H421A/H450A
Marketing Name:PowerLite Home Cinema 3010/PowerLite Home Cinema 3010e
Trade Name:
EPSON
Type of Product: WirelessHD Transmitter
Model:
AW-WH036TU/AW-WH036TE/AW-WH036TT
Marketing Name:WirelessHD Transmitter
Epson and PowerLite are registered trademarks, and Epson Exceed Your Vision is a registered logomark of
Seiko Epson Corporation. PrivateLine is a registered trademark and Epson Connection is a service mark of Epson
America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2011 Epson America, Inc. 7/11
Printed in XXXXXX
CPD-34999