Zanussi ZHC 951 Instruction Manual

INSTRUCTION BOOKLET
COOKER HOOD
ZHC 951
Thank you for buying a Zanussi product.
To enable you to use your appliance effectively and safely, please read this instruction
book carefully before using the appliance and retain for future reference. If you require
guidance in the use of the appliance or require further information on Zanussi Products,
please contact our Customer Care Department, at the address below or visit our website
at www.zanussi.co.uk
Customer Care Department
Zanussi
55 - 77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727 727*
*calls to this number may be recorded for traing purposes.
To register ownership, please ensure you complete and return the guarantee card
supplied with the appliance.
For the User
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
IMPORTANT SAFETY INFORMATION
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
These warnings are provided in the interests of safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance. If you are
unsure about any of the meanings of these warnings contact the Customer Care Department.
•
•
Installation
•
This hood must be installed in accordance
with the installation instructions and all
measurements must be adhered to.
•
If the cooker hood is installed for use above
a gas appliance then the provision for
ventilation must be in accordance with the
Gas Safety Codes of Practice BS.6172,
BS.5440 and BS.6891 (Natural Gas) and
BS.5482 (LP Gas) 1994, the Gas Safety
(Installation & Use) Regulations, the
Building Regulations issued by the
Department of the Environment, the
Building Standards (Scotland)
(Consolidated) Regulations issued by the
Scottish Development Department.
For the Installer
Important Safety Information
Technical Information
Electrical Connection
Your Appliance
Electrical Requirements
Electrical Connection
Operating Instructions
Cooker Hood Controls
To Operate
Recirculation
Extraction
Installing the Cooker Hood
Maintenance and Cleaning
External Cleaning
Metal Grease Filters
Charcoal Filters
To Remove/Replace the Charcoal
Filters
Changing the Light Bulb
Something Not Working
Installation Requirements
Unpacking
Clearance Heights
Fitting the Wall Brackets
Fitting the Canopy Hood
Venting
Recirculation
Fitting the Chimney Stack
•
To register ownership, please ensure you
complete and return the guarantee card
supplied with the appliance.
Service and Spare Parts
Guarantee Conditions
Safety instructions
Step by step instructions
1
The fan motor of this cooker hood
incorporates a cut-out device which will
operate if the cooker hood is installed
below the minimum height recommended
under the section ‘Clearance Height’, or if
the motor becomes overheated. If the cutout device is activated, switch off the fan
motor and allow the cooker hood to cool.
The cut-out device will reset itself when the
fan motor has cooled significantly.
It is dangerous to alter the specifications or
modify this product in any way.
•
When installed between adjoining wall
cabinets the wall cabinets must not
overhang the hob.
•
If the room where the cooker hood is to be
used contains a fuel burning appliance
such as a central heating boiler then its flue
must be of the room sealed or balanced
flue type.
•
If other types of flue or appliances are fitted
ensure that there is an adequate supply of
air to the room.
Guide to use the instruction book
The ducting system for this appliance must
not be connected to any existing ventilation
system which is being used for any other
purpose.
•
Do not install above a cooker with a high-level
grill.
•
•
Child Safety
•
•
During Use
•
Never leave frying pans unattended during
use as overheated fats and oils might catch
fire.
•
Never do flambé cooking under this cooker
hood.
•
Do not leave naked flames under the cooker
hood.
•
•
Maintenance and Service
•
Under no circumstances should you attempt
to repair the appliance yourself. Repairs
carried out by inexperienced persons may
cause injury or more serious malfunction.
Refer to your local Zanussi Service Force
Centre. Always insist on genuine spare
parts.
Any installation work must be undertaken
by a qualified electrician or a competent
person.
•
The following Symbols will be found in the text to guide you through the instruction book
•
2
This appliance is designed to be operated by
adults. Children should not be allowed to
tamper with the appliance.
This product is for domestic use only.
This appliance can be a hazard if the grease
filters and charcoal filters are not cleaned and
replaced as recommended.
Thank you for buying a Zanussi product.
To enable you to use your appliance effectively and safely, please read this instruction
book carefully before using the appliance and retain for future reference. If you require
guidance in the use of the appliance or require further information on Zanussi Products,
please contact our Customer Care Department, at the address below or visit our website
at www.zanussi.co.uk
Customer Care Department
Zanussi
55 - 77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727 727*
*calls to this number may be recorded for traing purposes.
To register ownership, please ensure you complete and return the guarantee card
supplied with the appliance.
For the User
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
IMPORTANT SAFETY INFORMATION
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
These warnings are provided in the interests of safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance. If you are
unsure about any of the meanings of these warnings contact the Customer Care Department.
•
•
Installation
•
This hood must be installed in accordance
with the installation instructions and all
measurements must be adhered to.
•
If the cooker hood is installed for use above
a gas appliance then the provision for
ventilation must be in accordance with the
Gas Safety Codes of Practice BS.6172,
BS.5440 and BS.6891 (Natural Gas) and
BS.5482 (LP Gas) 1994, the Gas Safety
(Installation & Use) Regulations, the
Building Regulations issued by the
Department of the Environment, the
Building Standards (Scotland)
(Consolidated) Regulations issued by the
Scottish Development Department.
For the Installer
Important Safety Information
Technical Information
Electrical Connection
Your Appliance
Electrical Requirements
Electrical Connection
Operating Instructions
Cooker Hood Controls
To Operate
Recirculation
Extraction
Installing the Cooker Hood
Maintenance and Cleaning
External Cleaning
Metal Grease Filters
Charcoal Filters
To Remove/Replace the Charcoal
Filters
Changing the Light Bulb
Something Not Working
Installation Requirements
Unpacking
Clearance Heights
Fitting the Wall Brackets
Fitting the Canopy Hood
Venting
Recirculation
Fitting the Chimney Stack
•
To register ownership, please ensure you
complete and return the guarantee card
supplied with the appliance.
Service and Spare Parts
Guarantee Conditions
Safety instructions
Step by step instructions
1
The fan motor of this cooker hood
incorporates a cut-out device which will
operate if the cooker hood is installed
below the minimum height recommended
under the section ‘Clearance Height’, or if
the motor becomes overheated. If the cutout device is activated, switch off the fan
motor and allow the cooker hood to cool.
The cut-out device will reset itself when the
fan motor has cooled significantly.
It is dangerous to alter the specifications or
modify this product in any way.
•
When installed between adjoining wall
cabinets the wall cabinets must not
overhang the hob.
•
If the room where the cooker hood is to be
used contains a fuel burning appliance
such as a central heating boiler then its flue
must be of the room sealed or balanced
flue type.
•
If other types of flue or appliances are fitted
ensure that there is an adequate supply of
air to the room.
Guide to use the instruction book
The ducting system for this appliance must
not be connected to any existing ventilation
system which is being used for any other
purpose.
•
Do not install above a cooker with a high-level
grill.
•
•
Child Safety
•
•
During Use
•
Never leave frying pans unattended during
use as overheated fats and oils might catch
fire.
•
Never do flambé cooking under this cooker
hood.
•
Do not leave naked flames under the cooker
hood.
•
•
Maintenance and Service
•
Under no circumstances should you attempt
to repair the appliance yourself. Repairs
carried out by inexperienced persons may
cause injury or more serious malfunction.
Refer to your local Zanussi Service Force
Centre. Always insist on genuine spare
parts.
Any installation work must be undertaken
by a qualified electrician or a competent
person.
•
The following Symbols will be found in the text to guide you through the instruction book
•
2
This appliance is designed to be operated by
adults. Children should not be allowed to
tamper with the appliance.
This product is for domestic use only.
This appliance can be a hazard if the grease
filters and charcoal filters are not cleaned and
replaced as recommended.
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
YOUR APPLIANCE
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
To Operate
Select the required fan speed and light if required.
The appliance can be installed to recirculate or
extract contaminated air. The cooker hood is more
effective when used in the extraction mode.
Recirculation
The cooker hood is supplied specified for use in the
recirculation mode with the charcoal filter fitted.
In the recirculation mode the contaminated air is
passed through the charcoal filters to be purified
and recirculated into the kitchen through the
recirculation grilles in either side of the chimney
stack.
Extraction
In the extraction mode the contaminated air enters
the cooker hood passing through the grease filters
and is passed out through the ducting into the
atmosphere.
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
OPERATING INSTRUCTIONS
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
Never leave frying pans unattended during
use as overheated fats and oils can catch
fire.
Cooker Hood Controls
The cooker hood functions are controlled by
four push button switches located centrally in
the control fascia.
V1
V2
V3
When used in the extraction mode the
charcoal filters are not required.
Never do flambé cooking under this
cooker hood.
This cooker hood is designed to extract
unpleasant odours from the kitchen, it
will not extract steam.
L
S
To obtain the best performance when cooking it is
advisable to switch the cooker hood on for a few
minutes before you start cooking and leave it
running for about 15 minutes after finishing.
Do not leave naked flames under the cooker
hood.
L
Turns the worktop lighting On and Off
Mains light - illumination indicates fan
motor is running
Turns the fan motor On and Off at low
speed, suitable for one pan or when
simmering.
Medium fan speed, suitable for use
when cooking with a number of pots
and pans.
Maximum fan speed, suitable for
cooking foods with strong odours.
S
3
V1
V2
Ensure heating areas on your hob are
covered with pots and pans when using the
hob and cooker hood simultaneously.
V3
4
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
YOUR APPLIANCE
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
To Operate
Select the required fan speed and light if required.
The appliance can be installed to recirculate or
extract contaminated air. The cooker hood is more
effective when used in the extraction mode.
Recirculation
The cooker hood is supplied specified for use in the
recirculation mode with the charcoal filter fitted.
In the recirculation mode the contaminated air is
passed through the charcoal filters to be purified
and recirculated into the kitchen through the
recirculation grilles in either side of the chimney
stack.
Extraction
In the extraction mode the contaminated air enters
the cooker hood passing through the grease filters
and is passed out through the ducting into the
atmosphere.
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
OPERATING INSTRUCTIONS
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
Never leave frying pans unattended during
use as overheated fats and oils can catch
fire.
Cooker Hood Controls
The cooker hood functions are controlled by
four push button switches located centrally in
the control fascia.
V1
V2
V3
When used in the extraction mode the
charcoal filters are not required.
Never do flambé cooking under this
cooker hood.
This cooker hood is designed to extract
unpleasant odours from the kitchen, it
will not extract steam.
L
S
To obtain the best performance when cooking it is
advisable to switch the cooker hood on for a few
minutes before you start cooking and leave it
running for about 15 minutes after finishing.
Do not leave naked flames under the cooker
hood.
L
Turns the worktop lighting On and Off
Mains light - illumination indicates fan
motor is running
Turns the fan motor On and Off at low
speed, suitable for one pan or when
simmering.
Medium fan speed, suitable for use
when cooking with a number of pots
and pans.
Maximum fan speed, suitable for
cooking foods with strong odours.
S
3
V1
V2
Ensure heating areas on your hob are
covered with pots and pans when using the
hob and cooker hood simultaneously.
V3
4
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
MAINTENANCE AND CLEANING
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
Before carrying out any maintenance
or cleaning isolate the cooker hood
from the mains supply.
The cooker hood must be kept clean,
as a build up of grease or fat can be a
fire hazard.
External Cleaning
Wipe the cooker hood frequently with warm soapy
water using a mild detergent.
Position the new charcoal filter in the
position marked and while holding the
filter replace the fixing hooks as
illustrated.
This appliance can be a possible fire
hazard if the grease and charcoal
filters are not cleaned and replaced as
recommended.
Changing the Spot Lamps
Remove the two screws fixing the
lighting support.
Remove the spot lamp from the holder
by pulling the lamp downwards.
Replace the spot lamp by inserting the
two pins at the base of the lamp into
the holes in holder and pushing into
position.
Never use scouring pads or abrasive
cleaners.
Never use excessive amounts of water
when cleaning particularly around the
control panel.
Replace the lighting support, ensuring it
is located correctly and fix back into
position using the two screws.
Metal Grease Filters
The grease filters absorb grease and dust during
cooking to help keep the cooker hood clean inside.
Cleaning
The filters must be washed once every
month, using a normal household
detergent; their compact dimension also
enables them to be washed in a
dishwasher. Allow to dry completely
before replacing.
If one of the spot lamps has failed to function
check that the lamp is fully seated into the lamp
holder. If lamp failure has occurred then it
should be replaced with a 12V 20W M262
halogen spot lamp.
Replacement filters and lamps can be
obtained from your local Service Force
Centre.
Removing and replacing the filters
Remove the filters one at a time, press
against the metal actuator to release the
spring catch as illustrated. When
replacing, ensure that the handles face
outwards.
Charcoal Filter
In the recirculation mode the charcoal filter
absorbs smells and unwanted odours.
The charcoal filter cannot be cleaned or
regenerated, and must be replaced approximately
every 4 months, or more frequently if the hood is
subjected to heavy usage.
Replacing the charcoal filter
First remove the metal grease filters.
Remove the saturated activated charcoal
filter by releasing the fixing hooks as
illustrated.
5
6
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
MAINTENANCE AND CLEANING
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
Before carrying out any maintenance
or cleaning isolate the cooker hood
from the mains supply.
The cooker hood must be kept clean,
as a build up of grease or fat can be a
fire hazard.
External Cleaning
Wipe the cooker hood frequently with warm soapy
water using a mild detergent.
Position the new charcoal filter in the
position marked and while holding the
filter replace the fixing hooks as
illustrated.
This appliance can be a possible fire
hazard if the grease and charcoal
filters are not cleaned and replaced as
recommended.
Changing the Spot Lamps
Remove the two screws fixing the
lighting support.
Remove the spot lamp from the holder
by pulling the lamp downwards.
Replace the spot lamp by inserting the
two pins at the base of the lamp into
the holes in holder and pushing into
position.
Never use scouring pads or abrasive
cleaners.
Never use excessive amounts of water
when cleaning particularly around the
control panel.
Replace the lighting support, ensuring it
is located correctly and fix back into
position using the two screws.
Metal Grease Filters
The grease filters absorb grease and dust during
cooking to help keep the cooker hood clean inside.
Cleaning
The filters must be washed once every
month, using a normal household
detergent; their compact dimension also
enables them to be washed in a
dishwasher. Allow to dry completely
before replacing.
If one of the spot lamps has failed to function
check that the lamp is fully seated into the lamp
holder. If lamp failure has occurred then it
should be replaced with a 12V 20W M262
halogen spot lamp.
Replacement filters and lamps can be
obtained from your local Service Force
Centre.
Removing and replacing the filters
Remove the filters one at a time, press
against the metal actuator to release the
spring catch as illustrated. When
replacing, ensure that the handles face
outwards.
Charcoal Filter
In the recirculation mode the charcoal filter
absorbs smells and unwanted odours.
The charcoal filter cannot be cleaned or
regenerated, and must be replaced approximately
every 4 months, or more frequently if the hood is
subjected to heavy usage.
Replacing the charcoal filter
First remove the metal grease filters.
Remove the saturated activated charcoal
filter by releasing the fixing hooks as
illustrated.
5
6
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
SOMETHING NOT WORKING
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
If, having followed these instructions carefully, your cooker hood fails to work properly please carry
out the following checks.
Solution
Symptom
The cooker hood will not start
•
•
•
•
•
•
•
The cooker hood has switched off during
operation
If after all these checks, the fault persists,
contact your local Service Force Centre, quoting
the model and serial number.
Please note that it will be necessary to provide
proof of purchase for any in-guarantee service
calls.
•
•
Check the hood is connected to the electricity
supply.
Make sure the switch is in the ‘ON’ position.
The fan speed is set high enough for the task.
The grease filter is clean.
08705 929929
Your telephone call will be routed to your local
Service Force Centre.
For the address of your local Service Force
Centre and further information about Service
Force, please visit the website at
www.serviceforce.co.uk
We, Zanussi, undertake that if within twenty four months of the date of the purchase this
Electrolux built-in product or any part thereof is proved to be defective by reason only of faulty
workmanship or materials, the company will, at our option repair or replace the same FREE OF
ANY CHARGE for labour, materials or carriage on condition that:
•
•
•
The kitchen is adequately vented to allow the
entry of fresh air.
•
If set up for recirculation, check that the
charcoal filter is still effective.
•
If set up for extraction, check that the ducting
outlets are not blocked.
The safety cut-out device has been tripped.
Turn off the hob and then wait for the device
to reset.
In-guarantee customers should ensure that
the above checks have been made as the
engineer will make a charge if the fault is not
a mechanical or electrical breakdown.
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
SERVICE AND SPARE PARTS
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
If you require an engineer or spare parts
contact your local Service Force Centre by
telephoning:
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
GUARANTEE CONDITIONS
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
For general assistance with your appliance or for
further information on Zanussi products please
contact our Customer Care Department at the
address below or visit our website at:
www.zanussi.co.uk
Customer Care Department
Zanussi
55 - 77 High Street
Slough
Berkshire
SL1 1DZ
Telephone: 08705 727 727*
* calls to this number may be recorded for training
purposes.
7
The appliance has been correctly installed and used only on the electrical supply stated on the
rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer’s operating and maintenance instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by
any person not authorised by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force
Centre.
Any appliance or defective part replaced shall become the property of this company.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available
outside these hours in which case a premium will be charged.
EXCLUSIONS
This Guarantee does not cover:
•
•
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of
any lamps or removable parts of glass or plastic.
Costs incurred for calls to put right appliances improperly installed or calls to appliances
outside the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are the
subject of rental agreements.
• Products of Zanussi manufacture which are not marked by Zanussi.
This guarantee is in addition to your statutory and legal rights.
ZANUSSI EUROPEAN GUARANTEE
If you should move to another country within Europe then your guarantee moves with you to your
new home subject to the following qualifications:
•
•
•
•
•
The guarantee starts from the date you first purchased the product.
The guarantee is for the same period and to the same extent for labour and parts as exists in
the new country of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used
domestically, i.e. a normal household.
Before you move please contact your nearest Customer Care Centre, listed below,
to give them detailsof your new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after you and your appliances.
France
Germany
Italy
Sweden
United Kingdom
Senlis
Nurnberg
Pordenone
Stockholm
Slough
+33
+49
+39
+46
+44
(0)3 44 62 22 22
(0)911 323 2600
(0)1678 47053
(0)20 78 77 50
(0)1753 219897
8
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
SOMETHING NOT WORKING
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
If, having followed these instructions carefully, your cooker hood fails to work properly please carry
out the following checks.
Solution
Symptom
The cooker hood will not start
•
•
•
•
•
•
•
The cooker hood has switched off during
operation
If after all these checks, the fault persists,
contact your local Service Force Centre, quoting
the model and serial number.
Please note that it will be necessary to provide
proof of purchase for any in-guarantee service
calls.
•
•
Check the hood is connected to the electricity
supply.
Make sure the switch is in the ‘ON’ position.
The fan speed is set high enough for the task.
The grease filter is clean.
08705 929929
Your telephone call will be routed to your local
Service Force Centre.
For the address of your local Service Force
Centre and further information about Service
Force, please visit the website at
www.serviceforce.co.uk
We, Zanussi, undertake that if within twenty four months of the date of the purchase this
Electrolux built-in product or any part thereof is proved to be defective by reason only of faulty
workmanship or materials, the company will, at our option repair or replace the same FREE OF
ANY CHARGE for labour, materials or carriage on condition that:
•
•
•
The kitchen is adequately vented to allow the
entry of fresh air.
•
If set up for recirculation, check that the
charcoal filter is still effective.
•
If set up for extraction, check that the ducting
outlets are not blocked.
The safety cut-out device has been tripped.
Turn off the hob and then wait for the device
to reset.
In-guarantee customers should ensure that
the above checks have been made as the
engineer will make a charge if the fault is not
a mechanical or electrical breakdown.
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
SERVICE AND SPARE PARTS
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
If you require an engineer or spare parts
contact your local Service Force Centre by
telephoning:
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
GUARANTEE CONDITIONS
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
For general assistance with your appliance or for
further information on Zanussi products please
contact our Customer Care Department at the
address below or visit our website at:
www.zanussi.co.uk
Customer Care Department
Zanussi
55 - 77 High Street
Slough
Berkshire
SL1 1DZ
Telephone: 08705 727 727*
* calls to this number may be recorded for training
purposes.
7
The appliance has been correctly installed and used only on the electrical supply stated on the
rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer’s operating and maintenance instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by
any person not authorised by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force
Centre.
Any appliance or defective part replaced shall become the property of this company.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available
outside these hours in which case a premium will be charged.
EXCLUSIONS
This Guarantee does not cover:
•
•
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of
any lamps or removable parts of glass or plastic.
Costs incurred for calls to put right appliances improperly installed or calls to appliances
outside the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are the
subject of rental agreements.
• Products of Zanussi manufacture which are not marked by Zanussi.
This guarantee is in addition to your statutory and legal rights.
ZANUSSI EUROPEAN GUARANTEE
If you should move to another country within Europe then your guarantee moves with you to your
new home subject to the following qualifications:
•
•
•
•
•
The guarantee starts from the date you first purchased the product.
The guarantee is for the same period and to the same extent for labour and parts as exists in
the new country of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used
domestically, i.e. a normal household.
Before you move please contact your nearest Customer Care Centre, listed below,
to give them detailsof your new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after you and your appliances.
France
Germany
Italy
Sweden
United Kingdom
Senlis
Nurnberg
Pordenone
Stockholm
Slough
+33
+49
+39
+46
+44
(0)3 44 62 22 22
(0)911 323 2600
(0)1678 47053
(0)20 78 77 50
(0)1753 219897
8
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
INSTALLATION INSTRUCTIONS
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
INSTALLING THE COOKER HOOD
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
Unpacking
It is dangerous to alter the specifications or attempt to modify this product in any way.
Technical information
DIMENSIONS
ELECTRICAL SUPPLY
SUITABLE FOR INSTALLATION ABOVE:
HEIGHT OF CANOPY: (incl glass visor)
HEIGHT OF CHIMNEY: (UPPER SECTION)
(LOWER SECTION)
46mm
215mm
740mm
WIDTH OF CANOPY:
DEPTH OF CANOPY:
898mm
700mm
(incl glass visor)
(incl glass visor)
VOLTAGE:
(~50Hz)
POWER CONSUMPTION:
FAN MOTOR:
LAMPS:
(4x20W)
ELECTRIC HOB:
GAS HOB:
SLOT-IN ELECTRIC COOKER:
SLOT-IN GAS COOKER:
230V
230W
150W
80W
7KW (MAX)
10KW (MAX)
12.4KW (MAX)
13.5KW (MAX)
Note: CE Marking certifies that this appliance complies with the
requirements laid down in EEC directive 89:336 (Electromagnetic
compatibility) and subsequent modifications and Low Votage directive
72/23/E.
DOUBLE INSULATED DO NOT EARTH
Electrical Requirements
This appliance is fitted with a 2 core mains
cable and must be permanently connected to
the electricity supply via a double-pole switch
having 3mm minimum contact gap on each
pole. A Switched Fuse Connection Unit to
BS.1363 Part 4, fitted with a 3 Amp fuse, is a
recommended mains supply connection
accessory to ensure compliance with the Safety
Requirements applicable to fixed wiring
instructions.
Any permanent electrical installation must
comply with the latest I.E.E. Regulations and
local Electricity Board regulations. For your own
safety this should be undertaken by a qualified
electrician e.g. your local Electricity Board, or a
contractor who is on the roll of the National
Inspection Council for Electrical Installation
Contracting (NICEIC).
Electrical Connection
Before connecting to the mains supply ensure
that the mains voltage corresponds to the
voltage on the rating plate inside the cooker
The hood is supplied with the following
components for installation as illustrated.
Item Qty
Description
1
1
Hood body, complete with:
Controls, lighting, blower and
filters
2
2.1
2.2
7.1
1
1
1
1
7.1a
7.1b
8a
8b
9a
9b
14
14.1
15
24
25
1
1
1
1
1
1
1
2
1
1
2
Item
12c
Qty
6
12e
2
12f
4
12g
4
12h
4
21
1
Item
Qty
1
21
23
Telescopic chimney comprising:
Upper section
Lower section
Telescopic frame complete with
extractor, consisting of:
Upper frame
Lower frame
Right-hand air outlet grille
Left-hand air outlet grille
Ø120-125mm Ducting collar
Ø150-120mm Ducting spigot
Recirculation extension ducting
Recirculation extension ducting
Recirculation spigot
Junction box
Jubilee Clips
12h
7.1a
15
12g
7.1
14.1
14
7.1b
9
12c
Installation Components
Ø2.9 x9.5mm Chimney fixing
screws
Ø2.9 x6.5mm Junction box
fixing screws
M6x10mm Hood body fixing
screws
M6x80mm Lower frame fixing
screws
Ø5.2x70mm Upper frame fixing
screws
Ceiling drilling template
25
2.1
2
2.2
8b
8a
12e
12c
Documents
Instruction Manual
12c
1
12f
This appliance conforms to BS.800:1988 and
EEC Directive No. 78 308 regarding
suppression of radio and television interference.
9
11
22
10
24
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
INSTALLATION INSTRUCTIONS
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
INSTALLING THE COOKER HOOD
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901
Unpacking
It is dangerous to alter the specifications or attempt to modify this product in any way.
Technical information
DIMENSIONS
ELECTRICAL SUPPLY
SUITABLE FOR INSTALLATION ABOVE:
HEIGHT OF CANOPY: (incl glass visor)
HEIGHT OF CHIMNEY: (UPPER SECTION)
(LOWER SECTION)
46mm
215mm
740mm
WIDTH OF CANOPY:
DEPTH OF CANOPY:
898mm
700mm
(incl glass visor)
(incl glass visor)
VOLTAGE:
(~50Hz)
POWER CONSUMPTION:
FAN MOTOR:
LAMPS:
(4x20W)
ELECTRIC HOB:
GAS HOB:
SLOT-IN ELECTRIC COOKER:
SLOT-IN GAS COOKER:
230V
230W
150W
80W
7KW (MAX)
10KW (MAX)
12.4KW (MAX)
13.5KW (MAX)
Note: CE Marking certifies that this appliance complies with the
requirements laid down in EEC directive 89:336 (Electromagnetic
compatibility) and subsequent modifications and Low Votage directive
72/23/E.
DOUBLE INSULATED DO NOT EARTH
Electrical Requirements
This appliance is fitted with a 2 core mains
cable and must be permanently connected to
the electricity supply via a double-pole switch
having 3mm minimum contact gap on each
pole. A Switched Fuse Connection Unit to
BS.1363 Part 4, fitted with a 3 Amp fuse, is a
recommended mains supply connection
accessory to ensure compliance with the Safety
Requirements applicable to fixed wiring
instructions.
Any permanent electrical installation must
comply with the latest I.E.E. Regulations and
local Electricity Board regulations. For your own
safety this should be undertaken by a qualified
electrician e.g. your local Electricity Board, or a
contractor who is on the roll of the National
Inspection Council for Electrical Installation
Contracting (NICEIC).
Electrical Connection
Before connecting to the mains supply ensure
that the mains voltage corresponds to the
voltage on the rating plate inside the cooker
The hood is supplied with the following
components for installation as illustrated.
Item Qty
Description
1
1
Hood body, complete with:
Controls, lighting, blower and
filters
2
2.1
2.2
7.1
1
1
1
1
7.1a
7.1b
8a
8b
9a
9b
14
14.1
15
24
25
1
1
1
1
1
1
1
2
1
1
2
Item
12c
Qty
6
12e
2
12f
4
12g
4
12h
4
21
1
Item
Qty
1
21
23
Telescopic chimney comprising:
Upper section
Lower section
Telescopic frame complete with
extractor, consisting of:
Upper frame
Lower frame
Right-hand air outlet grille
Left-hand air outlet grille
Ø120-125mm Ducting collar
Ø150-120mm Ducting spigot
Recirculation extension ducting
Recirculation extension ducting
Recirculation spigot
Junction box
Jubilee Clips
12h
7.1a
15
12g
7.1
14.1
14
7.1b
9
12c
Installation Components
Ø2.9 x9.5mm Chimney fixing
screws
Ø2.9 x6.5mm Junction box
fixing screws
M6x10mm Hood body fixing
screws
M6x80mm Lower frame fixing
screws
Ø5.2x70mm Upper frame fixing
screws
Ceiling drilling template
25
2.1
2
2.2
8b
8a
12e
12c
Documents
Instruction Manual
12c
1
12f
This appliance conforms to BS.800:1988 and
EEC Directive No. 78 308 regarding
suppression of radio and television interference.
9
11
22
10
24
Please ensure that when the appliance is
installed it is easily accessible to an engineer
in the event of a breakdown.
Drilling the Ceiling/Support
Shelf
Using a plumb line mark the centre point
of the hob on the ceiling or support
shelf.
All installations must comply with the local
authorities requirements for the discharge of
exhaust air.
Position the drilling template item 21 on
the ceiling or support shelf ensuring the
template is aligned correctly with the
angles of the hob.
Incorrect installation may affect the safety of
this cooker hood.
Installation Requirements
Mark the hole centres.
Before installation check that the wall to
which the cooker hood is to be fitted for
electric cables, water pipes and gas.
Pilot drill the fixing holes at the points
marked for the approprate size rawl
plugs and screws (not supplied).
This cooker hood is designed to be fixed to any
vertical surface over a cooking area, and can be
used in the extraction (ducted to the outside) or
recirculation mode.
The installation work must be undertaken by a
qualified and competent person.
It will also be necessary to drill a
Ø10mm hole for the mains cable and the
ducting if the hood is to be installed
ducted to the outside.
Fixing the Frame
The manufacturer disclaims any responsibility for
damage due to incorrect installation of the cooker
hood or if the hood is not installed in compliance with
relevant regulations controlling this type of installation.
Clearance Heights
The cooker hood is designed to be fitted over a
cooking appliance at the clearance heights stated,
providing the maximum output of the appliance
beneath does not exceed the maximums quoted in the
Technical Specifications.
If the output of the appliance below the cooker hood
exceeds the maximum outputs quoted, please refer to
the cooker manufacturer’s installation instructions.
A minimum clearance height of 650mm (25½ins) is
required when installed above a built-in electric hob,
or 700mm (27½ins) when installed above a built-in
gas hob.
A minimum clearance height of 685mm (27ins) is
required when installing above a slot-in electric
cooker, or 787mm (30½ins) when installed above a
slot-in cooker.
When installed between adjoining wall cabinets, the
wall cabinets must not overhang the hob and the
distance between the underside of the cabinet and
the worktop must be 450mmm (17¾ins), a gap of
50mm (2ins) must be maintained either side of the
hob.
This cooker hood must not be installed
above a cooking appliance with a high
level grill.
IMPORTANT: Before fixing, separate
the Upper Chimney section 2.1 and the
Lower Chimney section 2.2 from the
frame by removing the screws 12c.
Then separate the two sections of the
frame by unscrewing the 8 screws
located on each side of the frame.
Upper Frame
Feed the mains cable through the frame
and the hole in the ceiling or support
shelf.
Fix the Upper Frame 7.1a to the ceiling
(screws not supplied).
Lower Frame
Fix the lower frame using the 8
screws removed earlier and adjust the
length according to the installation
height (the minimum distance before
fitting the hood body 1 must be 710mm).
When the hood is to be installed in the
recirculation mode, position the frame in
the direction you want the recirculated
air to pass into the kitchen.
The frame mountings must be secure
enough to withstand the weight of the
cooker hood and any knocks the hood
may get through normal ware and tear.
The hood can be installed above these heights but for
optimum performance it should be installed at the
distances quoted for the appropriate heat source.
11
12
Please ensure that when the appliance is
installed it is easily accessible to an engineer
in the event of a breakdown.
Drilling the Ceiling/Support
Shelf
Using a plumb line mark the centre point
of the hob on the ceiling or support
shelf.
All installations must comply with the local
authorities requirements for the discharge of
exhaust air.
Position the drilling template item 21 on
the ceiling or support shelf ensuring the
template is aligned correctly with the
angles of the hob.
Incorrect installation may affect the safety of
this cooker hood.
Installation Requirements
Mark the hole centres.
Before installation check that the wall to
which the cooker hood is to be fitted for
electric cables, water pipes and gas.
Pilot drill the fixing holes at the points
marked for the approprate size rawl
plugs and screws (not supplied).
This cooker hood is designed to be fixed to any
vertical surface over a cooking area, and can be
used in the extraction (ducted to the outside) or
recirculation mode.
The installation work must be undertaken by a
qualified and competent person.
It will also be necessary to drill a
Ø10mm hole for the mains cable and the
ducting if the hood is to be installed
ducted to the outside.
Fixing the Frame
The manufacturer disclaims any responsibility for
damage due to incorrect installation of the cooker
hood or if the hood is not installed in compliance with
relevant regulations controlling this type of installation.
Clearance Heights
The cooker hood is designed to be fitted over a
cooking appliance at the clearance heights stated,
providing the maximum output of the appliance
beneath does not exceed the maximums quoted in the
Technical Specifications.
If the output of the appliance below the cooker hood
exceeds the maximum outputs quoted, please refer to
the cooker manufacturer’s installation instructions.
A minimum clearance height of 650mm (25½ins) is
required when installed above a built-in electric hob,
or 700mm (27½ins) when installed above a built-in
gas hob.
A minimum clearance height of 685mm (27ins) is
required when installing above a slot-in electric
cooker, or 787mm (30½ins) when installed above a
slot-in cooker.
When installed between adjoining wall cabinets, the
wall cabinets must not overhang the hob and the
distance between the underside of the cabinet and
the worktop must be 450mmm (17¾ins), a gap of
50mm (2ins) must be maintained either side of the
hob.
This cooker hood must not be installed
above a cooking appliance with a high
level grill.
IMPORTANT: Before fixing, separate
the Upper Chimney section 2.1 and the
Lower Chimney section 2.2 from the
frame by removing the screws 12c.
Then separate the two sections of the
frame by unscrewing the 8 screws
located on each side of the frame.
Upper Frame
Feed the mains cable through the frame
and the hole in the ceiling or support
shelf.
Fix the Upper Frame 7.1a to the ceiling
(screws not supplied).
Lower Frame
Fix the lower frame using the 8
screws removed earlier and adjust the
length according to the installation
height (the minimum distance before
fitting the hood body 1 must be 710mm).
When the hood is to be installed in the
recirculation mode, position the frame in
the direction you want the recirculated
air to pass into the kitchen.
The frame mountings must be secure
enough to withstand the weight of the
cooker hood and any knocks the hood
may get through normal ware and tear.
The hood can be installed above these heights but for
optimum performance it should be installed at the
distances quoted for the appropriate heat source.
11
12
Recirculation
On completion check that the base is stable
even if the frame is subject to movement.
The cooker hood is supplied specified for use in the
recirculation mode, with the charcoal filter fitted.
The installer must provide ample
support where the ceiling or support
shelf is not strong enough by
installing cross beams over the joists
or above the shelf to ensure the
frame is quite rigid at its mounting
point.
In the recirculation mode contaminated air is passed
through the charcoal filter to be purified and
recirculated into the kitchen through the grille outlets
on either side of the chimney.
Recirculation Connection
Assemble the two halves of the round
recirculation extension duct 14.
Extraction
The cooker hood is more effective when used in the
extraction mode (ducted to the outside).
15
Push fit the assembled extesion duct 14
on to Ø150mm ducting spigot on top of
the motor housing.
Venting kits may be purchased through your
retailer or DIY store, and must be ducted to an
outside vent of Ø125mm (5”) or Ø150mm (6”).
14.1
Push fit the recirculation spigot 15 onto
the other end of the extension duct 14.
For the best performance use the shortest possible
duct run and the minimum number of bends.
Where flexible ducting is fitted it should not be turned
through very tight bends as this may impair the
performance of the hood.
It is recommended a maximum length of 3 metres
with one bend, to be installed, to be reduced metre
for each 90o bend.
If a distance is greater than 3 metres the efficiency
of the hood could be impaired.
14
Insert the extension ducts item 14.1 into
either side of the recirculation spigot 14
ensuring the connections are vertically
and horizontally aligned with the outlets
in the chimney.
ø 150
Chimney Stack
ø120
25
The ducting used must be manufactured
from fire retardent material conforming to the
relevant British Standard or DIN 4102-B1.
25
9
The chimney consists of two sections. The lower
chimney measures 740mm (with the recirculation
grilles on either side) and the upper chimney
measures 215mm. The overall installed
measurement is min. 740-940mm max.
Fitting the Chimney
When the cooker hood is ducted to the outside the
charcoal filter must be removed.
Ducting Connection
Connect the ducting chosen to:
the Ø150mm ducting spigot on top of the
motor housing, or the Ø150-120mm ducting
spigot 9 and secure using the jubilee clips
25.
A Ø120-125mm collar 10 is provided
to fit over the Ø120mm ducting spigot
when 125mm ducting is fitted.
Position the upper chimney section 2.1 and
fix the chimney to the upper frame using two
Ø2.9x9.5mm screws 12c.
12c
Slide the lower chimney section 2.2 up over
the upper chimney and fix the chimny to the
lower frame using two Ø2.9x9.5mm screws
12c.
8b
When installed in the recirculation mode the
ducting outlet extension pieces 14.1 should
align with the rectangular holes in each side
of the chimney.
If the room where the cooker hood is to
be used contains a fuel burning
appliance such as a central heating
boiler, then its flue must be of the room
sealed or balanced flue type.
8a
12c
Position the recirculation grilles 8a and 8b so
the slats face in a forwards and upwards
direction.
Fitting the Hood Body 1
If other types of flue or appliances are fitted
ensure that there is an adequate supply of
air to the room.
12f
Before fixing the hood body to the frame:
Remove the grease filters from the hood
body.
Remove the activated charcoal filter.
Using the four M6x10 12f fix the hood body
1 to the frame 7.1b.
The cooker ducting (extraction mode) must
never be connected to central heating flues,
radiators or water heaters etc.
13
14
Recirculation
On completion check that the base is stable
even if the frame is subject to movement.
The cooker hood is supplied specified for use in the
recirculation mode, with the charcoal filter fitted.
The installer must provide ample
support where the ceiling or support
shelf is not strong enough by
installing cross beams over the joists
or above the shelf to ensure the
frame is quite rigid at its mounting
point.
In the recirculation mode contaminated air is passed
through the charcoal filter to be purified and
recirculated into the kitchen through the grille outlets
on either side of the chimney.
Recirculation Connection
Assemble the two halves of the round
recirculation extension duct 14.
Extraction
The cooker hood is more effective when used in the
extraction mode (ducted to the outside).
15
Push fit the assembled extesion duct 14
on to Ø150mm ducting spigot on top of
the motor housing.
Venting kits may be purchased through your
retailer or DIY store, and must be ducted to an
outside vent of Ø125mm (5”) or Ø150mm (6”).
14.1
Push fit the recirculation spigot 15 onto
the other end of the extension duct 14.
For the best performance use the shortest possible
duct run and the minimum number of bends.
Where flexible ducting is fitted it should not be turned
through very tight bends as this may impair the
performance of the hood.
It is recommended a maximum length of 3 metres
with one bend, to be installed, to be reduced metre
for each 90o bend.
If a distance is greater than 3 metres the efficiency
of the hood could be impaired.
14
Insert the extension ducts item 14.1 into
either side of the recirculation spigot 14
ensuring the connections are vertically
and horizontally aligned with the outlets
in the chimney.
¿ 150
Chimney Stack
¿ 120
25
The ducting used must be manufactured
from fire retardent material conforming to the
relevant British Standard or DIN 4102-B1.
25
9
The chimney consists of two sections. The lower
chimney measures 740mm (with the recirculation
grilles on either side) and the upper chimney
measures 215mm. The overall installed
measurement is min. 740-940mm max.
Fitting the Chimney
When the cooker hood is ducted to the outside the
charcoal filter must be removed.
Ducting Connection
Connect the ducting chosen to:
the Ø150mm ducting spigot on top of the
motor housing, or the Ø150-120mm ducting
spigot 9 and secure using the jubilee clips
25.
A Ø120-125mm collar 10 is provided
to fit over the Ø120mm ducting spigot
when 125mm ducting is fitted.
Position the upper chimney section 2.1 and
fix the chimney to the upper frame using two
Ø2.9x9.5mm screws 12c.
12c
Slide the lower chimney section 2.2 up over
the upper chimney and fix the chimny to the
lower frame using two Ø2.9x9.5mm screws
12c.
8b
When installed in the recirculation mode the
ducting outlet extension pieces 14.1 should
align with the rectangular holes in each side
of the chimney.
If the room where the cooker hood is to
be used contains a fuel burning
appliance such as a central heating
boiler, then its flue must be of the room
sealed or balanced flue type.
8a
12c
Position the recirculation grilles 8a and 8b so
the slats face in a forwards and upwards
direction.
Fitting the Hood Body 1
If other types of flue or appliances are fitted
ensure that there is an adequate supply of
air to the room.
12f
Before fixing the hood body to the frame:
Remove the grease filters from the hood
body.
Remove the activated charcoal filter.
Using the four M6x10 12f fix the hood body
1 to the frame 7.1b.
The cooker ducting (extraction mode) must
never be connected to central heating flues,
radiators or water heaters etc.
13
14
Electrical Connection
Push fit the Cmd connecter on the cable
from the motor housing to the one from the
control box.
Place the Cmd connector in the junction box
24 and clamp it together using two
Ø2.9x6.5mm screws 12e.
24
12e
Fix the junction box 24 to the hood body 1
using the two Ø2.9x9.5mm screws 12c.
Working Test
When the electrical connection has been made, test
the three speed fan and worktop illumination.
Cmd
12c
15
© Electrolux plc 2002
436001739 01 - 030415